Symbol Technologies AP7562 802.11 abgn/ac Access Point User Manual Rev

Symbol Technologies Inc 802.11 abgn/ac Access Point Rev

User Manual Rev

AP-7562 ACCESS POINTINSTALLATION GUIDE
2AP-7562 Access Point Zebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark of Symbol Technologies, Inc., a Zebra Technologies company.© 2015 Symbol Technologies, Inc.
Installation Guide 31.0 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.1 Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51.2 AP-7562 Hardware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.3 AP-7562 Antenna Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61.3.1 AP-7562 Dual Band 2.4 GHz / 5 GHz Antennas - US and Canada . . . . . . . . 71.3.2 AP-7562 Single Band 2.4 GHz Antennas - US and Canada . . . . . . . . . . . . 71.3.3 AP-7562 Single Band 5 GHz Antenna - US and Canada . . . . . . . . . . . . . . . 71.3.4 Outdoor Elevation Gain Configuration for US SKUs . . . . . . . . . . . . . . . . . . 81.3.5 AP-7562 Dual Band 2.4 GHz / 5 GHz Antennas - EU . . . . . . . . . . . . . . . . . . 81.3.6 AP-7562 Single Band 2.4 GHz Antennas - EU . . . . . . . . . . . . . . . . . . . . . . . 81.3.7 AP-7562 Single Band 5 GHz Antenna - EU. . . . . . . . . . . . . . . . . . . . . . . . . . 81.4 Hardware and Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.5 AP-7562 Mounting Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.6 AP-7562 Weatherized Ethernet Accessory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91.7 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.8 Hardware Installation Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101.8.1 Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111.8.2 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121.9 Access Point Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.10 AP-7562 Hardware Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.10.1 AP-7562 Ports and Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131.10.2 AP-7562 Antenna Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141.10.3 AP-7562 Antenna Mouting Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . 151.10.4 AP-7562 Grounding Post . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161.11 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 172.0 AP-7562 Hardware Mounting and Installation . . . . . . . . . . . . . . . . . . . . . . . . 182.1 Mounting Bracket Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.1.1 Extension Arm Kit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 192.2 Pole Mounted Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
4AP-7562 Access Point 2.2.1 Vertical Pole Mount . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 212.2.2 Wall Mounted Installations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 272.3 AP-7562 Power Options Using Power over Ethernet . . . . . . . . . . . . . . . . . . . . . 293.0 Basic Access Point Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 304.0 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.1 Physical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.2 Environmental Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 414.3 Power Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 425.0 Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435.1 Wireless Country Approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 435.2 Frequency of Operation - FCC and IC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.3 Industry Canada Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.4 Health and Safety Recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.4.1 Warnings for the Use of Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . 445.4.2 Potentially Hazardous Atmospheres . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 445.5 RF Exposure Guidelines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455.6 Power Supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 455.7 Radio Frequency Interference Requirements - FCC . . . . . . . . . . . . . . . . . . . . . . 455.7.1 Radio Transmitters (Part 15) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 475.8 Radio Frequency Interference Requirements - Canada . . . . . . . . . . . . . . . . . . . 475.9 CE Marking and European Economic Area (EEA) . . . . . . . . . . . . . . . . . . . . . . . . 485.10 Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485.11 Other Countries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 485.12 Waste Electrical and Electrical Equipment (WEEE) . . . . . . . . . . . . . . . . . . . . . 525.13 Turkish WEEE Statement of Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 536.0 Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 547.0 Symbol Technologies End-User Software License Agreement . . . . . . . . . 558.0 AP-7562 Series ROHS Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Installation Guide 51 IntroductionDesigned for extending network coverage to outside areas, the AP-7562 brings the latest 802.11ac 3x3:3 Multiple Input Multiple Output (MIMO) dual radio design together with rugged outdoor performance. The AP-7562 is a 3x3:3 802.11ac Access Point utilizing one 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio. The AP-7562 is optimized with WiNG intelligence, extending QoS, security, and mobility services to the Access Point to support better capacity and performance.Deployments can be managed using WiNG architecture. WiNG architecture leverages the best aspects of independent and dependent architectures to create a smart network that meets the connectivity, quality, and security needs of each user and their applications based on the availability of network resources, including wired networks.Once adopted by a WLAN or Integrated Services Controller running WiNG firmware, the AP-7562 is managed as an Adaptive AP, running the WiNG network management protocol. WiNG networks extend the current differentiation that Adaptive APs offered to the next level by now having the services and security available at every point in the network. The traffic flow is optimized to prevent wired congestion. Traffic flows dynamically, based on user and application, and finds alternate routes to work around any possible network choke points. Mixed-media application optimization is the hallmark of WiNG 5 networks.1.1 Document ConventionsThe following graphical alerts are used in this document to indicate notable situations:NOTE Tips, hints, or special requirements that you should take note of.CAUTION Care is required. Disregarding a caution can result in data loss or equipment malfunction.WARNING! Indicates a condition or procedure that could result in personal injury or equipment damage.!
6AP-7562 Access Point 1.2 AP-7562 HardwareThere are currently three AP-7562 Access Points:1.3 AP-7562 Antenna AccessoriesThe AP-7562 antenna suite includes the following optional antenna accessories. The antennas do not ship with the AP-7562 Access Points and must be ordered separately.Model Part Number DescriptionAP-7562-67040-US AP-7562 Access Point outdoor IP67 dual radio 3x3:3 802.11 a/b/g/n/ac radio SKU: USAP-7562-67040-EU AP-7562 Access Point outdoor IP67 dual radio 3x3:3 802.11 a/b/g/n/ac radio SKU: EUAP-7562-67040-WR AP-7562 Access Point outdoor IP67 dual radio 3x3:3 802.11 a/b/g/n/ac radio SKU: WRNOTE All AP-7562 Access Points ship with one weatherized Ethernet adapter. AP-7562 Access Points do not ship with the Mounting Kit/Antenna and POE injector. These items must be ordered separately.NOTE Antennas must be ordered separately and are not included with the AP-7562.
Installation Guide 71.3.1 AP-7562 Dual Band 2.4 GHz / 5 GHz Antennas - US and Canada1.3.2 AP-7562 Single Band 2.4 GHz Antennas - US and Canada1.3.3 AP-7562 Single Band 5 GHz Antenna - US and CanadaPart Number Antenna Type 2.4 GHz Peak Gain 5.2 GHz Peak GainML-2452-HPAG4A6-01 Dipole 4.0 7.3ML-2452-HPA6X6-036 Dipole 4.0 7.3ML-2452-HPA6-01 Dipole 5.3 6.1ML-2452-PNA5-01R Panel 5.5 6.0ML-2452-PNL3M3-1 Polarized Panel 9.7 9.2Part Number Antenna Type 2.4 GHz Peak GainML-2499-FHPA5-01R Dipole 5.3ML-2499-HPA4-01 Dipole 4.5ML-2499-5PNL-72-N Panel 6.5Part Number Antenna Type 5.2 GHz Peak GainML-5299-HPA5-01 Dipole 5.6
8AP-7562 Access Point 1.3.4 Outdoor Elevation Gain Configuration for US SKUsPer FCC requirement, the use of the Access Point on UNII-1 band requires installers to input antenna elevation gain for dipole antennas during configuration. This information can be found in Zebra antenna guide document at www.zebra.com/support.The applicable outdoor antennas on 5GHz band are shown below:1.3.5 AP-7562 Dual Band 2.4 GHz / 5 GHz Antennas - EU1.3.6 AP-7562 Single Band 2.4 GHz Antennas - EU1.3.7 AP-7562 Single Band 5 GHz Antenna - EUIndex Antenna Type Part Number Elevation Gain1 Dipole ML-5299-HPA5-01 -2.532 Dipole ML-2452-HPAG4A6-01 5.73 Dipole ML-2452-HPA6X6-036 3.94 Dipole ML-2452-HPA6-01 4.09Part Number Antenna Type 2.4 GHz Peak Gain 5.2 GHz Peak GainML-2452-HPAG5A8-01 Dipole 7.5 8.0ML-2452-PNA7-01R Panel 8.0 12.0ML-2452-PNL3M3-1 Polarized Panel 9.7 9.2Part Number Antenna Type 2.4 GHz Peak GainML-2499-FHPA9-01R Dipole 10.5ML-2499-HPA8-01 Dipole 8.0Part Number Antenna Type 5.2 GHz Peak GainML-5299-HPA10-01 Dipole 10.5ML-5299-HPA5-01 Dipole 5.6
Installation Guide 91.4 Hardware and Mounting AccessoriesThe AP-7562 is a Power over Ethernet (PoE) device. When deployed, the use of an outdoor rated PoE power supply and mounting bracket may be required. The recommended PoE accessories are listed in the following table:1.5 AP-7562 Mounting AccessoriesThe AP-7562 has a flexible three piece mounting kit (KT-147407-01), together with an optional standoff extension arm (KT-150173-01) for pole mounting.1.6 AP-7562 Weatherized Ethernet AccessorysOne RJ45 weatherized connector plug is included with each AP-7562 Access Point. If additional plugs are required, they can be ordered using the part number listed in the following table:Refer to the installation instructions included with the RJ45 weatherized connector plug for proper procedure to form a drip loop with the cable.Part Number DescriptionAP-PSBIAS-7161-US Outdoor IP66 802.3AT gigabit Ethernet power injector, 100-240 VAC USAP-PSBIAS-7161-WW Outdoor IP66 802.3AT gigabit Ethernet power injector, 100-240 VAC InternationalKT-153143-01 Outdoor PoE mounting kitPart Number DescriptionKT-147407-01 Hardware Mounting KitKT-150173-01 12 inch extension arm for mounting kitPart Number DescriptionKT-153676-01 RJ45 weatherized connector plugCAUTION When connecting RJ45 cables, ensure that all cables are connected to the Access Point from the bottom, and include a drip loop to prevent moisture intrusion. Cover the Ethernet cable with self-healing weatherproofing tape.!
10 AP-7562 Access Point 1.7 Package ContentsCarefully remove all protective packing material around the AP-7562 Access Point and save the container for storage. Refer to AP-7562 Hardware on page 6 when verifying all AP-7562 hardware has been received. Record the serial numbers on the shipping cartons and AP-7562 for warranty claims and reference during software download procedures.When opening the shipping cartons, inspect the equipment for damage. If you find any damaged equipment or any equipment is missing, contact Support immediately.Each AP-7562 Access Point (see AP-7562 Hardware on page 6) includes the following parts:• AP-7562 Access Point• Weatherproof RJ45 plug kit•AP-7562 Access Point Installation Guide (this document)1.8 Hardware Installation GuidelinesNOTE Record the serial numbers on the shipping cartons and AP-7562 Access Points for warranty claims and reference during software download procedures.CAUTION All device wiring must comply with the National Electric Code (NEC) or regulations and procedures defined by the regulatory bodies of the country or region where the devices are being deployed. All local building and structure codes must be observed.WARNING! Strictly observe safety precautions and warnings when installing an AP-7562 Access Point.!
Installation Guide 111.8.1 PrecautionsBefore installing an AP-7562 Access Point, verify the following grounding and lightning protection guidelines:• The installation professional should be familiar with all grounding requirements and regional codes and ensure the Access Point and mounting asset are properly grounded. The grounding cable for an AP-7562 must be at a minimum a #10 gauge wire cross section. The cable can be attached to the unit using one of the following methods:• Loosen the grounding screw, insert the grounding cable into the hole below it, and tighten the screw.• Loosen the grounding screw, wind the grounding cable around it, and tighten the screw.• Attach a ring lug to the grounding cable and secure it to the unit using the grounding screw.• To properly attach the grounding cable to the Access Point, refer to AP-7562 Grounding Post on page 16.• For Ethernet and lightning protection, it is recommended that a commercially available off-the-shelf Lightning Protection Unit (LPU) be used on all shielded CAT5E Ethernet connections. The LPU should be rated for outdoor use.• For the best possible protection, each Access Point requires an LPU be installed adjacent to the Access Point. If there is a LAN connection to an indoor network, a second LPU is required at the cable entry point to the building.• Verify the deployment environment has a continuous temperature range compatible with the operating temperature range of the device.CAUTION Lightning damage is not covered under the conditions of a standard product warranty. When installed correctly, Lightning Protection Units (LPUs) provide the best protection from the harmful effects of lightning. Observe all regional and national codes that apply for lightning protection.!
12 AP-7562 Access Point 1.8.2 Warnings• Read all installation instructions and site survey reports, and verify correct equipment installation before connecting the Access Point to its power source.• Remove jewelry and watches before installing this equipment.• Verify the unit is grounded before connecting it to the power source.• Verify any device connected to this unit is properly wired and grounded.• Connect all power cords to a properly wired and grounded electrical circuit. Verify the electrical circuits have appropriate overload protection.• Attach only approved power cords to the device.• Verify the power connector and socket are accessible at all times during the operation of the equipment.• Do not hold any component containing a radio such that it is very close to or touching any exposed parts of the body, especially the face or eyes, while transmitting.• Do not work with power circuits in dimly lit spaces.• Do not install this equipment or work with its power circuits during thunderstorms or other weather conditions that could cause a power surge.• Verify there is adequate ventilation around the device, and that ambient temperatures meet equipment operation specifications.• Avoid contact with overhead power lines.• Take precautions to avoid injury from falling tools and equipment. Crews should wear hard hats in and around the installation work site.• Be aware of vehicular traffic in and around the installation work site.• Do not operate a portable transmitter near unshielded blasting caps or in an environment where explosives are present unless the transmitter is especially certified for such use.• Refer to your site survey and network analysis reports to determine specific requirements for each deployment.• Assign installation responsibility to the appropriate personnel.• Identify and document where all installed components are located.• Identify and prepare Ethernet and console port connections.• Verify cable lengths are within the maximum allowable distances for optimal signal transmission.CAUTION The maximum length allowed for PoE cables is 100 meters.CAUTION When connecting RJ45 cables, ensure that all cables are connected to the Access Point from the bottom, and include a drip loop to prevent moisture intrusion.!!
Installation Guide 131.9 Access Point PlacementObserve the following recommended guidelines:• Identify each piece of the mounting bracket and mounting extension arm hardware and ancillary hardware.• Mount the device with the black gore vent down.• Mounting height for network devices should not exceed 30 to 35 feet. Mounting height should vary to accommodate the topography of the deployment area, foliage, and other obstructions.• Devices can be deployed using any of the recommended outdoor deployment procedures.•Line of Sight (LoS) guidelines should be given special consideration when deploying devices.1.10 AP-7562 Hardware OverviewThe AP-7562 is a 3x3:3 802.11ac Access Point utilizing one 2.4 GHz 802.11n radio and one 5 GHz 802.11ac radio.An AP-7562 must be installed by trained professionals familiar with RF planning and regulatory limits defined by the regulatory bodies of the country where the devices are being deployed. All common precautions for grounding and Electrostatic Discharge (ESD) protection should be observed during deployment and installation. AP-7562 Access Points must be installed such that no harmful interference results from device operation.1.10.1 AP-7562 Ports and ConnectionsThe AP-7562 Access Point has the following port designations:• Antenna ports R1-A, B and C, R2-A, B and C• Console port• GE1/POE - LAN port• GE2 - WAN port
14 AP-7562 Access Point 1.10.2 AP-7562 Antenna ConnectorsAP-7562 Access Points (AP-7562-67040-US, AP-7562-67040-EU and AP-7562-67040-WR) are configured with six N type connectors to support two active WLAN data radios.WARNING! Antenna ports where no antenna is mounted must be properly terminated using an approved IP67 terminator.WARNING! All antenna connectors should be covered with weatherproofing tape.
Installation Guide 151.10.3 Antenna Mounting GuidelinesThe following are examples of acceptable mounting for dipole antenna deployments:The following are examples of acceptable mounting methods for panel antenna deployments:
16 AP-7562 Access Point 1.10.4 AP-7562 Grounding PostThe grounding post is located on the bottom of the Access Point above the GND symbol.The grounding cable can be attached to the unit using one of the following methods: • Use a grounding screw to securely attach the grounding cable to the grounding post. Use an 8mm socket and driver to tighten the grounding screw to 30 inch pounds (lbf-in).• Attach a ring lug to the grounding cable and use a grounding screw to securely attach the ring lug to the Access Point. Use an 8mm socket and driver to tighten the grounding screw to 30 inch pounds (lbf-in).WARNING! The grounding cable for an AP-7562 must be at a minimum a #10 gauge wire cross section.
Installation Guide 171.11 LED IndicatorsAP-7562 Access Points have LED activity indicators on the front of the enclosure. The LEDs provide a status display indicating error conditions, transmission, and network activity for the 2.4 GHz radio (green) and the 5 GHz radio (amber). Task 2.4 GHz Activity LED (Green) 5 GHz Activity LED (Amber)Unconfigured RadioOn OnNormal Operation• If this radio band is enabled: Blink at 5 second interval• If this radio band is disabled:Off• If there is activity on this band:Blink interval at 1 time per second• If this radio band is enabled: Blink at 5 second interval• If this radio band is disabled:Off• If there is activity on this band:Blink interval at 1 time per secondFirmware UpdateOff OnLocate AP ModeLEDs blink in an alternating green, red and amber pattern using an irregular blink rate. This LED state in no way resembles normal operating conditionsLEDs blink in an alternating green, red and amber pattern using an irregular blink rate. This LED state in no way resembles normal operating conditions.
18 AP-7562 Access Point 2 AP-7562 Hardware Mounting and InstallationThe AP-7562 mounting bracket kit (KT-147407-01) is recommended for most deployments.. When a standoff distance is required for a pole mounted or wall mounted installation, use the extension arm kit (KT-150173-01).2.1 Mounting Bracket KitThe AP-7562 mounting bracket kit (KT-147407-01) includes the Access Point bracket (left), angle adapter bracket (center), and pole mount bracket (right) sections:The Access Point bracket and angle adapter bracket can be rotated (plus or minus 15 degrees) and tilted (up to 45 degrees) to orient the unit for optimal positioning.The following ancillary hardware to assemble the mounting bracket is included in the kit:A torque wrench or ratchet with a 10mm adapter, or an adjustable wrench, can be used to assemble the mounting brackets.Description QuantityM6 serrated hex flanged screws 71/2 inch hex head nut 21/2 inch x 3/4 inch hex head bolt 2
Installation Guide 192.1.1 Extension Arm KitWhen mounting an AP-7562 on poles more than 3 inches in diameter, use the extension arm kit (KT-150173-01) to provide a minimum standoff distance of twelve inches to avoid interference with the antennas. The extension arm kit can also be used in combination with the any of the brackets from the mounting bracket kit.
20 AP-7562 Access Point The following ancillary hardware to attach the extension arm to the mounting bracket kit is included in the extension arm kit:2.2 Pole Mounted InstallationsThe mounting hardware kit and extension arm can be used in various combinations to properly install the AP-7562 on a pole. For poles of up to 3 inches in diameter, attach the pole mount bracket of the mounting hardware kit at the desired position on the pole using band clamps up to 3/4 inch width, or a 1/2 inch x 4 inch wide U-bolt and nuts. For poles greater than 3 inches in diameter, attach the pole mount bracket using band clamps.Description Quantity1/2 inch hex head nut 21/2 inch x 3/4 inch hex head bolt 2CAUTION Always mount the AP-7562 with the black gore vent facing down.NOTE The U-bolt and band clamps are not included in the mounting bracket kit.NOTE Use of the extension arm is recommended for installations on poles greater than 3 inches in diameter.!
Installation Guide 212.2.1 Vertical Pole MountUse the following procedure for vertical pole mount installations. The extension arm is recommended when mounting the Access Point to poles greater than 3 inches is diameter.For poles up to 3 inches in diameter when using a U-bolt:1. Thread two 1/2 inch nuts onto the U-bolt.2. Position the U-bolt on the pole and place the pole mount bracket on the U bolt. Adjust the two 1/2 inch inner nuts until the pole mount bracket is against the pole and the U-bolt can be secured tightly to the pole at the desired mounting location.3. Place the angle adapter bracket on the U-bolt with the open slot connections on the bottom and align it with the pole mount. Attach with two 1/2 inch nuts. Tighten all nuts to 300 inch pounds (lbf-in).
22 AP-7562 Access Point 4. Position the Access Point bracket so the bottom of the section with the straight (not bevel cut) side is oriented toward the bottom side of the AP with the gore vent. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the Access Point bracket to the AP-7562 with the four M6 flange screw.5. Insert two M6 hex flange screws into the bottom holes on the sides of the Access Point bracket.
Installation Guide 236. With the Access Point positioned so the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the Access Point bracket into the open slot connections on the bottom of the angle adapter bracket.7. Rotate the Access Point bracket upward and align the top holes on the sides with the top holes on the angle adapter bracket. Insert two M6 hex flange screws into the top holes on the angle adapter bracket.
24 AP-7562 Access Point 8. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the Access Point bracket to the angle adapter bracket with the M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket. Do not tighten the screws until all rotation and tilt adjustments are complete.9. To adjust the position of the Access Point, rotate the Access Point bracket (plus or minus 15 degrees) and tilt the angle adapter bracket (up to 45 degrees).10. Tighten all hex flange screws to 60 inch pounds (lbf-in).For mounting with band clamps:1. Attach the pole mount bracket at the desired mounting location using band clamps.2. With the angle adapter bracket positioned so the open connector slots are on the bottom, attach the angle adapter bracket to the pole mount bracket using two 1/2 inch bolts and nuts. Tighten the nuts to 300 inch pounds (lbf-in).3. Position the Access Point bracket so the bottom of the with the straight (not bevel cut) sides is oriented toward the bottom side of the AP with the gore vent. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the Access Point bracket to the AP-7562 with the four M6 hex flange screws.4. Insert two M6 hex flange screws into the bottom holes on the sides of the Access Point bracket.5. With the Access Point positioned so the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the Access Point bracket into the open slot connections on the bottom of the angle adapter bracket.
Installation Guide 256. Rotate the Access Point bracket upward and align the top holes on the sides with the top holes on the angle adapter bracket. Insert two M6 hex flange screws into the top holes on the angle adapter bracket. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the Access Point bracket to the angle adapter bracket with the M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket. Do not tighten the screws until all rotation and tilt adjustments are complete.7. To adjust the position of the Access Point, rotate the Access Point bracket (plus or minus 15 degrees) and tilt the angle adapter bracket (up to 45 degrees).8. Tighten all hex flange screws to 60 inch pounds (lbf-in).To use the extension arm with the mounting hardware kit:1. Attach the pole mount at the desired mounting location using a U-bolt or band clamps.2. Complete the steps for assembling and positioning the mounting bracket sections for poles less than or greater than 3 inches. See Vertical Pole Mount on page 21.
26 AP-7562 Access Point 3. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach the extension arm to the Access Point bracket with four M6 hex flange screws. The two oval holes must be positioned on the short sides of the Access Point. Tighten the hex flange screws to 60 inch pounds (lbf-in) the unit.4. With the Access Point positioned so the gore vent is facing down, attach the extension arm to the Access Point bracket with two 1/2 inch bolts and nuts. Tighten the nuts to 300 inch pounds (lbf-in).
Installation Guide 272.2.2 Wall Mounted InstallationsFor wall mounted installations, use only the Access Point bracket and angle adjust bracket if required.1. With the open slot connections facing down, attach the angle adjust bracket at the desired mounting location using four #10/32 lag bolts.2. Using a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, attach (but don’t tighten) the Access Point bracket to the AP-7562 with four M6 hex flange screws and insert two M6 hex flange screws into the bottom holes on the sides of the Access Point bracket.CAUTION Always mount the AP-7562 with the black gore vent facing down.NOTE The U-bolt and band clamps are not included in the mounting bracket kit.NOTE The lag bolts are not included in the mounting bracket kit.!
28 AP-7562 Access Point 3. With the Access Point positioned so the gore vent is facing down, insert the two M6 hex flange screws in the bottom holes on the sides of the Access Point bracket into the open slot connections on the bottom of the angle adapter bracket. Rotate the Access Point bracket upward and align the top holes on the sides with the top holes on the angle adapter bracket. Insert two M6 hex flange screws into the top holes on the angle adapter bracket.4. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to finish attaching the angle adapter bracket to the Access Point bracket with the four M6 hex flange screws in the open slot connections and the top holes on the angle adapter bracket. Do not tighten the screws until all rotation and tilt adjustments are complete.5. To adjust the position of the Access Point, rotate the Access Point bracket (plus or minus 15 degrees) and tilt the angle adapter bracket (up to 45 degrees).6. Use a torque wrench or a ratchet and a 10mm socket, or an adjustable wrench, to tighten all screws when all adjustments are complete.7. Tighten all hex flange screws to 60 inch pounds (lbf-in).To use the extension arm with the mounting hardware kit:1. With the open slot connections facing down, attach the angle adjust bracket at the desired mounting location using four #10/32 lag bolts.2. Complete the steps for assembling and positioning the angle adapter bracket and Access Point bracket sections outlined above. See Vertical Pole Mount on page 21.3. With the Access Point positioned so the gore vent is facing down, attach the extension arm to the Access Point bracket with two ½ inch bolts and nuts. Tighten bolts to 300 inch pounds (lbf-in).
Installation Guide 292.3 AP-7562 Power Options Using Power over EthernetPower over Ethernet (PoE) is the power source for an AP-7562 Access Point. For optimal performance, an AP-7562 can be powered by the following injectors and RFS controllers that support 802.AT PoE.For installations requiring an outdoor PoE injector, the following options are recommended:• AP-PSBIAS-7161-US• AP-PSBIAS-7161-WWThe AP-PSBIAS-7161 is a 1-Port 802.3at PoE Gigabit Ethernet injector. The injector is IP66 rated for outdoor deployments when used with the weatherproof kit supplied.There are two power cord options. The AP-PSBIAS-7161-US comes equipped with a cable with a standard three prong power plug. This plug can be removed by the installer if required when connecting to an AC source. The AP-PSBIAS-7161-WW comes equipped with a cable with open leads. Mounting kits are not supplied (see Hardware and Mounting Accessories on page 9 for mounting kit part numbers).If located within 100 meters of the controller and a PoE port is available, the AP-7562 Access Point can also be connected directly to a WLAN or Integrated Services Controller running WiNG 5.6 or higher.A standard CAT5E cable can be used to provide the connection to the AP-7562. The GE1/POE port on the AP-7562 is where the standard CAT5E cable will connect to the Access Point and use of the weatherproof RJ45 plug kit that comes with the unit will maintain a weatherproof seal for outdoor installation at the ethernet port.If a CAT5E cable is used to connect the Access Point to an RFS controller through a building egress, a suitable lightning protection system should be considered. A professional installer should be consulted to identify an appropriate system.NOTE Product installation and mounting instructions are provided with the outdoor power injector.
30 AP-7562 Access Point 3 Basic Access Point ConfigurationOnce the Access Point is installed and powered on, complete the following steps to get the device up and running and access management functions:1. Attach an Ethernet cable from the Access Point to a controller with an 802.3af compatible power source to supply power to the AP-7562 (once fully cabled).If your host system is a DHCP server, an IP address is automatically assigned to the AP-7162 and can be used for device connection. However, if a DHCP server is not available, you’ll need to derive the IP address from the AP MAC address. Using this method, the last two bytes of the MAC address become the last two octets of the IP address. For example:MAC address - 00:C0:23:00:F0:0A Zero-Config IP address - 169.254.240.10To derive the Access Point’s IP address using its MAC address:a. Open the Windows calculator be selecting Start > All Programs > Accessories > Calculator. This menu path may vary slightly depending on your version of Windows.b. With the Calculator displayed, select View > Scientific. Select the Hex radio button.c. Enter a hex byte of the Access Point’s MAC address. For example, F0.2. Select the Dec radio button. The calculator converts F0 into 240. Repeat this process for the last Access Point MAC address octet.Point the Web browser to the Access Point’s IP address. The following login screen displays:
Installation Guide 313. Enter the default username admin in the Username field.4. Enter the default password admin123 in the Password field.5. Click the Login button to load the management interface. 6. If this is the first time the management interface has been accessed, the Initial Setup Wizard automatically displays.The Introduction screen displays the various actions that can be performed using the wizard under the Function Highlight field.NOTE When logging in for the first time, you’re prompted to change the password to enhance device security in subsequent logins.NOTE If you get disconnected when running the wizard, you can connect again with the Access Point’s actual IP address (once obtained) and resume the wizard.
32 AP-7562 Access Point Use the Choose One type to Setup the Access Point field options to select the type of wizard to run. The Typical Setup is the recommended wizard. This wizard uses the default parameters for most of the configuration parameters and sets up a working network with the least amount of manual configuration. The Advanced Setup wizard is for administrators who prefer more control over the different configuration parameters. A few more configuration screens are available for customization when the Advanced Setup wizard is used.The first page of the Initial Setup Wizard displays the Navigation Panel and Function Highlights for the configuration activities comprising the Access Point's initial setup. This page also displays options to select the typical or advanced mode for the wizard.The Navigation Panel for the Typical Setup Wizard displays the basic configuration options.A green checkmark to the left of an item in the Navigation Panel defines the task as having its minimum required configuration set correctly. A red X defines a task as still requiring at least one parameter be defined correctly.
Installation Guide 337. Select Save/Commit within each page to save the updates made to that page's configuration. Select Next to proceed to the next page listed in the Navigation Panel without saving your updates.For the purposes of this guide, use the Typical Setup (Recommended) option to simplify the process of getting the Access Point up and running quickly with a minimum number of changes to the Access Point’s default configuration.For information on using the Access Point’s Advanced Setup option, refer to the WiNG Access Point System Reference Guide to familiarize yourself with the feature set supported by the WiNG operating system. The guide is available at www.zebra.com/support.To configure the Access Point using the Typical Setup Wizard:8. Select Typical Setup from the Choose One type to Setup the Access Point field on the Initial Setup Wizard.9. The Typical Setup Wizard displays the Access Point Settings screen to define the Access Point's Standalone versus Virtual Controller AP functionality. This screen also enables selection of the country of operation for the Access Point.NOTE While you can navigate to any page in the navigation panel, you cannot complete the Initial AP Setup Wizard until each task in the Navigation Panel has a green checkmark.
34 AP-7562 Access Point 10. Select an Access Point Type from the following options: •Virtual Controller AP - When more than one Access Point is deployed, a single Access Point can function as a Virtual Controller AP. Up to 24 Access Points can be connected to, and managed by, a single Virtual Controller AP of the same Access Point type. These connected Access Points must be the same type as the Virtual Controller AP.•Standalone AP - Select this option to deploy this Access Point as an autonomous fat Access Point. A Standalone AP isn't managed by a Virtual Controller AP, or adopted by a controller.11. Select the Country Code of the country where the Access Point is deployed. Selecting a proper country is a critical task while configuring the Access Point, as it defines the correct channels of operation and ensures compliance to the regulations of the selected country. This field is only available for the Typical Setup Wizard.12. Select Next to set the Access Point’s network mode.NOTE If wanting to adopt the Access Point to a controller or service platform, use the controller or service platform’s resident UI to connect to the Access Point, provision its configuration and administrate the Access Point’s configuration.NOTE If designating the Access Point as a Standalone AP, it is recommended the Access Point’s UI be used exclusively to define its device configuration, and not the CLI. The CLI provides the ability to define more than one profile and the UI does not. Consequently, the two interfaces cannot be used collectively to manage profiles without an administrator encountering problems.NOTE Access Point AP-7562-67040-US lists US as the only option in the list of country codes.
Installation Guide 3513. The Typical Setup Wizard displays the Network Topology screen to define how the Access Point handles network traffic.14. Select an Access Point Mode from the available options.•Router Mode -In Router Mode, the Access Point routes traffic between the local network (LAN) and the Internet or external network (WAN). Router mode is recommended in a deployment supported by just a single Access Point.•Bridge Mode - In Bridge Mode, the Access Point depends on an external router for routing LAN and WAN traffic. Routing is generally used on one device, whereas bridging is typically used in a larger density network. Select Bridge Mode when deploying this Access Point with numerous peer Access Points supporting clients on both the 2.4GHz and 5GHz radio bands. NOTE When Bridge Mode is selected, WAN configuration cannot be performed and the Typical Setup Wizard does not display the WAN configuration screen.
36 AP-7562 Access Point 15. Select Next. The Typical Setup Wizard displays the LAN Configuration screen to set the Access Point's LAN interface configuration.16. Set the following DHCP and Static IP Address/Subnet information for the LAN interface:•Use DHCP - Select the checkbox to enable an automatic network address configuration using the Access Point’s DHCP server.•Static IP Address/Subnet - Enter an IP Address and a subnet for the Access Point's LAN interface. If Use DHCP is selected, this field is not available. When selecting this option, define the following DHCP Server and Domain Name Server (DNS) resources, as those fields will become enabled on the bottom portion of the screen.•Use on-board DHCP server to assign IP addresses to wireless clients - Select the checkbox to enable the Access Point’s DHCP server to provide IP and DNS information to clients on the LAN interface.•Range - Enter a starting and ending IP Address range for client assignments on the LAN interface. Avoid assigning IP addresses from x.x.x.1 - x.x.x.10 and x.x.x.255, as they are often reserved for standard network services. This is a required parameter.•Default Gateway - Define a default gateway address for use with the default gateway. This is a required parameter.
Installation Guide 37•DNS Forwarding - Select this option to allow a DNS server to translate domain names into IP addresses. If this option is not selected, a primary and secondary DNS resource must be specified. DNS forwarding is useful when a request for a domain name is made but the DNS server, responsible for converting the name into its corresponding IP address, cannot locate the matching IP address. •Primary DNS - Enter an IP Address for the main Domain Name Server providing DNS services for the Access Point's LAN interface.•Secondary DNS - Enter an IP Address for the backup Domain Name Server providing DNS services for the Access Point's LAN interface.17. Select Next. The Typical Setup Wizard displays the Wireless LAN Setup screen to set the Access Point’s Wireless LAN interface configuration.18. Set the following WLAN1 Configuration parameters:•SSID - Configure the SSID for the WLAN. •WLAN Type - Configure the encryption and authentication to use with this WLAN.•No Authentication and No Encryption - Configures a network without any authentication. This option also configures the network without encryption. This means that any data transmitted through the network is in plain text. Any device between end points can see the information transmitted. This is the least secure of all network configurations.•Captive Portal Authentication and No Encryption - Configures a network that uses a RADIUS server to authenticate users before allowing them on to the network. Once on the network, no encryption is used for the data being transmitted through the network. Select this option to use a Web page (either internally or externally hosted) to authenticate users before access is granted to the network.•PSK authentication, WPA2 encryption - Configures a network that uses PSK authentication and WPA2 encryption. Select this option to implement a pre-shared key that must be correctly shared between the Access Point and requesting clients using this WLAN.
38 AP-7562 Access Point 19. Select Next. The Typical Setup Wizard displays the RADIUS Server Configuration screen if required.Otherwise, the Typical Setup Wizard displays the Summary and Commit screen.20. Use the Radius Server Configuration screen to configure the users for the onboard RADIUS server. Use the screen to add, modify and remove RADIUS users.
Installation Guide 3921. Select Add User to display the dialog to enter user information to add to the RADIUS server user database.22. Enter the following user information:•Username - Provide a user name used to authenticate the user.•Password - Provide a password used to authenticate the user.• Confirm Password - Confirm the password by entering the same password as entered in the Password field.• Description - Provide a description to identify the user created in the RADIUS server database.23. To create the entry in the RADIUS server database and add another user, select Create. To create the entry in the RADIUS server database and close the Add User dialog, select Create & Close.24. Select Modify User on the RADIUS Server Configuration screen to modify information for an existing user from the RADIUS database. Highlight the user entry then select Modify User.25. Select Delete User on the RADIUS Server Configuration screen to remove information for an existing user from the RADIUS database. Highlight the user entry and select Delete User.26. Select Confirm on the dialog displayed. The entry for the user is removed from the RADIUS database.27. To dismiss the dialog without adding, modifying or removing entries in the RADIUS server database, select Cancel.NOTE The Username cannot be modified with this dialog.
40 AP-7562 Access Point 28. Select Next. The Typical Setup Wizard displays the Summary and Commit screen to summarize the screens (pages) and settings updated using the Typical Setup Wizard.No user intervention or additional settings are required. Its an additional means of validating the Access Point’s updated configuration before it’s deployed. However, if a screen displays settings not intended as part of the initial configuration, then any screen can be selected again from within the Navigation Panel and its settings modified accordingly.29. If the configuration displays as intended, select Save/Commit to implement these settings to the Access Point’s configuration. If additional changes are warranted based on the summary, either select the target page from the Navigational Panel, or use the Back and Next buttons to scroll to the target screen.
Installation Guide 414 Specifications4.1 Physical Characteristics4.2 Environmental CharacteristicsDimensions 9.0 in. L x 10.0 in. W x 2.6 in. H22.8 cm L x 25.4 cm W x 6.6 cm HWeight (Unit) 5.6lbs / 2.54 KgHousing Outdoor IP67 rated, die-cast aluminum, corrosion resistant enclosure, salt, fog, rust perASTM B117LED activity indication 2 top mounted LEDsUplink 2 ports (GE1/GE2) auto-sensing 10/100/1000BaseT Ethernet; 802.3at on GE1 LAN portAntenna Connectors 6 N-Type console portsConsole Port Outdoor rated RJ45 console portMulti Band Security Sensor Outdoor 24x7 Wireless Intrusion Prevention System (WIPS)Operating Temperature -22° F to 140° F/-30° C to 60° CStorage Temperature -40° F to 140° F/-40° C to 60° COperating Humidity 5 to 95% RH non-condensingIP Sealing IP 67Operating Altitude 8,000 ft. at 12 °CStorage Altitude 30,000 ft. at 28 °CWind Rating 150 mphElectrostatic Discharge 15kV air, 8kV contactOperational Shock IEC60721-3-4, Class 4M3, MIL STD 810FOperational Vibration IEC60721-3-4, Class 4M3
42 AP-7562 Access Point 4.3 Power CharacteristicsOperating Voltage 36-57 VDCOperating Current 375mA at 48V in 802.3at modeIntegrated PoE 802.3af, 802.3at
Installation Guide 435 Regulatory InformationThis device is approved under Zebra Technologies Corporation.All Zebra devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required.Local language translations are available at the following website:www.zebra.com/supportAny changes or modifications to Zebra equipment, not expressly approved by Zebra Technologies, could void the user's authority to operate the equipment.Zebra devices are professionally installed, the Radio Frequency Output Power will not exceed the maximum allowable limit for the country of operation.Antennas: Use only the supplied or an approved replacement antennas. Unauthorized antennas, modifications, or attachments could cause damage and may violate regulations.5.1 Wireless Country ApprovalsRegulatory markings are applied to the device signifying the radio(s) are approved for use in the following countries: United States, Canada, Australia, and Europe.Please refer to the Declaration of Conformity (DoC) for details of other country markings. This is available at: www.zebra.com/doc.Note: Europe includes, Austria, Belgium, Bulgaria, Czech Republic, Cyprus, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Liechtenstein, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovak Republic, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.Operation of the device without regulatory approval is illegal.Country SelectionSelect only the country in which you are using the device. Any other selection will make the operation of this device illegal.
44 AP-7562 Access Point 5.2 Frequency of Operation - FCC and IC2.4 GHz OnlyThe available channels for 802.11bg operation in the US are Channels 1 to 11. The range of channels is limited by firmware.5.3 Industry Canada StatementCaution: The device for the band 5150-5250 MHz is only for indoor usage to reduce potential for harmful interference to co-Channel mobile satellite systems. High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LE-LAN devices.Avertissement: Le dispositive fonctionnant dans la bande 5150-5250 MHz est réservé uniquement pour une utilisation à l'intérieur afin de réduire les risques de brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux.Les utilisateurs de radars de haute puissance sont désignés utilisateurs principaux (c.-à-d., qu'ils ont la priorité) pour les bands 5250-5350 MHz et 5650-5850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL5.4 Health and Safety Recommendations5.4.1 Warnings for the Use of Wireless DevicesPlease observe all warning notices with regard to the usage of wireless devices.5.4.2 Potentially Hazardous AtmospheresWireless devices transmit radio frequency energy and may affect medical electrical equipment. When installed adjacent to other equipment, it is advised to verify the adjacent equipment is not adversely affected.PacemakersPacemaker manufacturers recommended that a minimum of 15cm (6 inches) be maintained between a handheld wireless device and a pacemaker to avoid potential interference with the pacemaker. These recommendations are consistent with independent research and recommendations by Wireless Technology Research.NOTE The EIRP for all outdoor antennas used in the 5.15 - 5.25 GHz band should not exceed a maximum 125 mW ERIP (21dBm) at any elevation angle above 30 degrees (21dBm).
Installation Guide 45Persons with Pacemakers:1.Should ALWAYS keep the device more than 15cm (6 inches) from their pacemaker when turned ON.2.Should not carry the device in a breast pocket.3.Should use the ear furthest from the pacemaker to minimise the potential for interference.4.If you have any reason to suspect that interference is taking place, turn OFF your device. Other Medical DevicesPlease consult your physician or the manufacturer of the medical device, to determine if the operation of your wireless product may interfere with the medical device.5.5 RF Exposure GuidelinesReduce RF Exposure - Use ProperlyOnly operate the device in accordance with the instructions supplied.InternationalThe device complies with internationally recognized standards covering human exposure to electromagnetic fields from radio devices. For information on "International" human exposure to electromagnet fields refer to the Declaration of Conformity (DoC) at www.zebra.com/doc.For further information on the safety of RF energy from wireless devices - see www.zebra.com/support.Located under Wireless Communications and HealthEuropeRemote and Standalone Antenna ConfigurationsTo comply with EU RF exposure requirements, antennas that are mounted externally at remote locations or operating near users at stand-alone desktop of similar configurations must operate with a minimum separation distance of 35 cm from all persons.
46 AP-7562 Access Point US and CanadaCo-located statementTo comply with FCC RF exposure compliance requirement, the antenna used for this transmitter must not be co-located or operating in conjunction with any other transmitter/antenna except those already approved in this filling.To satisfy US and Canadian RF exposure requirements, a transmitting device must operate with a minimum separation distance of 35 cm or more from a person's body. Pour satisfaire aux exigences Américaines et Canadiennes d'exposition aux radiofréquences, un dispositif de transmission doit fonctionner avec une distance de séparation minimale de 35 cm ou plus de corps d'une personne.5.6 Power SupplyThis device must be powered from a 802.3af or 802.3at compliant power source which has been certified by the appropriate agencies, or by a LISTED Type no. PWRS-14000-247R or AP-PSBIAS-2P3-ATR, direct plug-in power supply, marked Class 2 or LPS (IEC60950-1,SELV). Use of alternative Power Supply will invalidate any approvals given to this unit and may be dangerous5.7 Radio Frequency Interference Requirements - FCCThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna• Increase the separation between the equipment and receiver• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.
Installation Guide 475.7.1 Radio Transmitters (Part 15)This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.5.8 Radio Frequency Interference Requirements - CanadaFor RLAN Devices:The use of 5 GHz RLAN's, for use in Canada, have the following restrictions:• Restricted Band 5.60 - 5.65 GHzThis device complies with RSS 210 of Industry Canada. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation.Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada applicable aux appareils radio exempts de licence. Son fonctionnement est sujet aux deux conditions suivantes: (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable.Label Marking: The Term "IC:" before the radio certification only signifies that Industry Canada technical specifications were metTo reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that permitted for successful communication.The device could automatically discontinue transmission in case of absence of information to trans-mit, or operational failure. Note that this is not intended to prohibit transmission of control or signaling information or the use of repetitive codes where required by the technology.In compliance with respective local regulatory law, Access Point software provides professional installers the option to configure the antenna type and antenna gain for approved antennas.This radio transmitter MODEL: AP-7562 has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.Le présent émetteur radio MODEL: AP-7562 a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés ci-dessous et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de l'émetteur.Refer AP-7562 Antenna Accessories on page 6 of this guide for a listing of the 2.4 and 5 GHz antennas initially approved for use with the AP-7562.
48 AP-7562 Access Point 5.9 CE Marking and European Economic Area (EEA)The use of 2.4 GHz RLAN’s, for use through the EEA, have the following restrictions:• Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 -2.4835 GHz• Italy requires a user license for outside usage.5.10 Statement of ComplianceZebra hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A Declaration of Conformity may be obtained from www.zebra.com/doc.5.11 Other CountriesAustraliaUse of 5 GHz RLAN’s in Australia is restricted in the following band: 5.50 – 5.65 GHz.Brazil (UNWANTED EMISSIONS - ALL PRODUCTS)Regulatory Declarations for AP-7562 - BRAZILFor more information consult the website http://www.anatel.gov.br.Declarações Regulamentares para AP-7562 - BrasilNota: A marca de certificação se aplica ao Transceptor, modelo AP-7562. Este equipamento opera em caráter secundário, isto é, não tem direito a proteção contra interferência prejudicial, mesmo de estações do mesmo tipo, e não pode causar interferência a sistemas operando em caráter primário. Para maiores informações sobre ANATEL consulte o site: http://www.anatel.gov.br.ChileEste equipo cumple con la Resolución No 403 de 2008, de la Subsecretaria de telecomunicaciones, relativa a radiaciones electromagnéticas.Chinawww.zebra.com/supporthttp://www.tenaa.com.cn/
Installation Guide 49Hong Kong In accordance with HKTA1039, the band 5.15GHz - 5.35GHz is for indoor operation only.MexicoRestrict Frequency Range to: 2.450 – 2.4835 GHz.La operación de este equipo está sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no deseada.S. KoreaFor a radio equipment using 2400~2483.5MHz or 5725~5825MHz, the following two expression should be displayed;
50 AP-7562 Access Point Taiwan「電磁波曝露量 MPE 標準值 1mW/cm2，本產品使用時建議應距離人體：35 cm」。
Installation Guide 51UkraineThailand
52 AP-7562 Access Point 5.12 Waste Electrical and Electronic Equipment (WEEE)English: For EU Customers: All products at the end of their life must be returned to Zebra for recycling. For information on how to return product, please go to: www.zebra.com/weee.Français: Clients de l'Union Européenne: Tous les produits en fin de cycle de vie doivent être retournés à Zebra pour recyclage. Pour de plus amples informations sur le retour de produits, consultez: www.zebra.com/weee.Español: Para clientes en la Unión Europea: todos los productos deberán entregarse a Zebra al final de su ciclo de vida para que sean reciclados. Si desea más información sobre cómo devolver un producto, visite: www.zebra.com/weee.Бъгаи: З   ЕС: С я  я     я     Zebra  . З я    , я   : www.zebra.com/weee.Deutsch: Für Kunden innerhalb der EU: Alle Produkte müssen am Ende ihrer Lebensdauer zum Recycling an Zebra zurückgesandt werden. Informationen zur Rücksendung von Produkten finden Sie unter www.zebra.com/weee.Italiano: per i clienti dell'UE: tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Zebra al fine di consentirne il riciclaggio. Per informazioni sulle modalità di restituzione, visitare il seguente sito Web: www.zebra.com/weee.Português: Para clientes da UE: todos os produtos no fim de vida devem ser devolvidos à Zebra para reciclagem. Para obter informações sobre como devolver o produto, visite: www.zebra.com/weee.Nederlands: Voor klanten in de EU: alle producten dienen aan het einde van hun levensduur naar Zebra te worden teruggezonden voor recycling. Raadpleeg www.zebra.com/weee voor meer informatie over het terugzenden van producten.Polski: Klienci z obszaru Unii Europejskiej: Produkty wycofane z eksploatacji nale¿y zwróciæ do firmy Zebra w celu ich utylizacji. Informacje na temat zwrotu produktów znajduj¹ siê na stronie internetowej www.zebra.com/weee.Čeština: Pro zákazníky z EU: Všechny produkty je nutné po skonèení jejich životnosti vrátit spoleènosti Zebra k recyklaci. Informace o zpùsobu vrácení produktu najdete na webové stránce: www.zebra.com/weee.Eesti: EL klientidele: kõik tooted tuleb nende eluea lõppedes tagastada taaskasutamise eesmärgil Zebra 'ile. Lisainformatsiooni saamiseks toote tagastamise kohta külastage palun aadressi: www.zebra.com/weee.Magyar: Az EU-ban vásárlóknak: Minden tönkrement terméket a Zebra vállalathoz kell eljuttatni újrahasznosítás céljából. A termék visszajuttatásának módjával kapcsolatos tudnivalókért látogasson el a www.zebra.com/weee weboldalra.Svenska: För kunder inom EU: Alla produkter som uppnått sin livslängd måste returneras till Zebra för återvinning. Information om hur du returnerar produkten finns på www.zebra.com/weee.Suomi: Asiakkaat Euroopan unionin alueella: Kaikki tuotteet on palautettava kierrätettäväksi Zebra-yhtiöön, kun tuotetta ei enää käytetä. Lisätietoja tuotteen palauttamisesta on osoitteessa www.zebra.com/weee.Dansk: Til kunder i EU: Alle produkter skal returneres til Zebra til recirkulering, når de er udtjent. Læs oplysningerne om returnering af produkter på: www.zebra.com/weee.Εηνά: Γα π  Ε.Ε.: Όα α ποα, ο ο  α  ου, ππ α πφοα  Zebra γα αα. Γα π ποφο χ   ποφ  ποο, πφ  υ www.zebra.com/weee ο ∆αυο.
Installation Guide 53Malti: Għal klijenti fl-UE: il-prodotti kollha li jkunu waslu fl-aħħar tal-ħajja ta' l-użu tagħhom, iridu jiġu rritornati għand Zebra għar-riċiklaġġ. Għal aktar tagħrif dwar kif għandek tirritorna l-prodott, jekk jogħġbok żur: www.zebra.com/weee.Românesc: Pentru clienţii din UE: Toate produsele, la sfârşitul duratei lor de funcţionare, trebuie returnate la Zebra pentru reciclare. Pentru informaţii despre returnarea produsului, accesaţi: www.zebra.com/weee.Slovenski: Za kupce v EU: vsi izdelki se morajo po poteku življenjske dobe vrniti podjetju Zebra za reciklažo. Za informacije o vračilu izdelka obiščite: www.zebra.com/weee.Slovenčina: Pre zákazníkov z krajín EU: Všetky výrobky musia byť po uplynutí doby ich životnosti vrátené spoločnosti Zebra na recykláciu. Bližšie informácie o vrátení výrobkov nájdete na: www.zebra.com/weee.Lietuvių: ES vartotojams: visi gaminiai, pasibaigus jų eksploatacijos laikui, turi būti grąžinti utilizuoti į kompaniją „ Zebra“. Daugiau informacijos, kaip grąžinti gaminį, rasite: www.zebra.com/weee.Latviešu: ES klientiem: visi produkti pēc to kalpošanas mūža beigām ir jānogādā atpakaļ Zebra otrreizējai pārstrādei. Lai iegūtu informāciju par produktu nogādāšanu Zebra, lūdzu, skatiet: www.zebra.com/weee.Türkçe: AB Müşterileri için: Kullanım süresi dolan tüm ürünler geri dönüştürme için Zebra'ya iade edilmelidir. Ürünlerin nasıl iade edileceği hakkında bilgi için lütfen şu adresi ziyaret edin: www.zebra.com/weee.5.13 Turkish WEEE Statement of Compliance
54 AP-7562 Access Point 6 SupportIf you have a problem with your equipment, contact support for your region.Contact information is available at: www.zebra.com/support.When contacting support, please provide the following information:• Serial number of the unit• Model number or product name• Software type and version numberSupport responds to calls by e-mail, telephone, or fax within the time limits set forth in support agreements. If you purchased your product from a business partner, contact that business partner for support.Customer Support Web SitesThe Support site, located at www.zebra.com/support.provides information and online assistance including developer tools, software downloads, product manuals and online repair requests.Manualswww.zebra.com/support.
Installation Guide 557 Symbol Technologies End-User Software License AgreementThis End-User Software License Agreement ("End-User License Agreement") is between Symbol Technologies Inc. (herein "Symbol Technologies") and End-User Customer to whom Symbol Technologies' proprietary software or Symbol Technologies Products containing embedded, pre-loaded, or installed software ("Products") is made available. This End-User License Agreement contains the terms and conditions of the license Symbol Technologies is providing to End-User Customer, and End-User Customer's use of the Software and Documentation. By using, downloading or installing this software, you or the entity that you represent ("End-User Customer") are consenting to be bound by and are becoming a party to this End-User License Agreement..1. DEFINITIONS “Documentation” means product and software documentation that specifies technical and performancefeatures and capabilities, and the user, operation and training manuals for the Software (including allphysical or electronic media upon which such information is provided).“Open Source Software” means software with either freely obtainable source code license formodification, or permission for free distribution.“Open Source Software License” means the terms or conditions under which the Open SourceSoftware is licensed.“Software” (i) means proprietary software in object code format, and adaptations, translations,decompilations, disassemblies, emulations, or derivative works of such software; (ii) means anymodifications, enhancements, new versions and new releases of the software provided by SymbolTechnologies; and (iii) may contain items of software owned by a third party supplier. The term“Software” does not include any third party software provided under separate license or third partysoftware not licensable under the terms of this Agreement. To the extent, if any, that there is a separatelicense agreement packaged with, or provided electronically with, a particular Product that becomeseffective on an act of acceptance by the end user, then that agreement supersedes this End-User LicenseAgreement as to the end use of that particular Product.2. GRANT OF LICENSE2.1 Subject to the provisions of this End-User License Agreement, Symbol Technologies grants to End-UserCustomer a personal, limited, non-transferable (except as provided in Section 4), and non-exclusivelicense under Symbol Technologies’ copyrights and confidential information embodied in the Software touse the Software, in object code form, and the Documentation solely in connection with End-UserCustomer’s use of the Products. This End-User License Agreement does not grant any rights to sourcecode.
56 AP-7562 Access Point 2.2 If the Software licensed under this End-User License Agreement contains or is derived from Open SourceSoftware, the terms and conditions governing the use of such Open Source Software are in the OpenSource Software Licenses of the copyright owner and not this End-User License Agreement. If there is aconflict between the terms and conditions of this End-User License Agreement and the terms andconditions of the Open Source Software Licenses governing End-User Customer’s use of the Open SourceSoftware, the terms and conditions of the license grant of the applicable Open Source Software Licenseswill take precedence over the license grants in this End-User License Agreement. If requested byEnd-User Customer, Symbol Technologies will use commercially reasonable efforts to: (i) determinewhether any Open source Software is provided under this End-User License Agreement; (ii) identify theOpen Source Software and provide End-User Customer a copy of the applicable Open Source SoftwareLicense (or specify where that license may be found); and, (iii) provide End-User Customer a copy of theOpen Source Software source code, without charge, if it is publicly available (although distribution feesmay be applicable).3. LIMITATIONS ON USE 3.1 End-User Customer may use the Software only for End-User Customer’s internal business purposes andonly in accordance with the Documentation. Any other use of the Software is strictly prohibited and willbe deemed a breach of this End-User License Agreement. Without limiting the general nature of theserestrictions, End-User Customer will not make the Software available for use by third parties on a “timesharing,” “application service provider,” or “service bureau” basis or for any other similar commercialrental or sharing arrangement.3.2 End-User Customer will not, and will not allow or enable any third party to: (i) reverse engineer,disassemble, peel components, decompile, reprogram or otherwise reduce the Software or any portion toa human perceptible form or otherwise attempt to recreate the source code; (ii) modify, adapt, createderivative works of, or merge the Software with other software; (iii) copy, reproduce, distribute, lend, orlease the Software or Documentation to any third party, grant any sublicense or other rights in theSoftware or Documentation to any third party, or take any action that would cause the Software orDocumentation to be placed in the public domain; (iv) remove, or in any way alter or obscure, anycopyright notice or other notice of Symbol Technologies’ proprietary rights; (v) provide, copy, transmit,disclose, divulge or make the Software or Documentation available to, or permit the use of the Softwareby any third party or on any machine except as expressly authorized by this Agreement; or (vi) use, orpermit the use of, the Software in a manner that would result in the production of a copy of the Softwaresolely by activating a machine containing the Software. End-User Customer may make one copy ofSoftware to be used solely for archival, back-up, or disaster recovery purposes; provided that End-UserCustomer may not operate that copy of the Software at the same time as the original Software is being
Installation Guide 57operated. End-User Customer may make as many copies of the Documentation as it may reasonablyrequire for the internal use of the Software. 3.3 Unless otherwise authorized by Symbol Technologies in writing, End-User Customer will not, and will notenable or allow any third party to: (i) install a licensed copy of the Software on more than one unit of aProduct; or (ii) copy onto or transfer Software installed in one unit of a Product onto another device.3.4 If End-User Customer is purchasing Products that require a site license, End-User Customer mustpurchase a copy of the applicable Software for each site at which End-User Customer uses suchSoftware. End-User Customer may make one additional copy for each computer owned or controlled byEnd-User Customer at each such site. End-User Customer may temporarily use the Software on portableor laptop computers at other sites. End-User Customer must provide a written list of all sites whereEnd-User Customer uses or intends to use the Software.4. TRANSFERS 4.1 End-User Customer will not transfer the Software or Documentation to any third party without SymbolTechnologies’ prior written consent. Symbol Technologies’ consent may be withheld at its discretion andmay be conditioned upon transferee paying all applicable license fees and agreeing to be bound by thisEnd-User License Agreement. 5. OWNERSHIP AND TITLE 5.1 Symbol Technologies, its licensors, and its suppliers retain all of their proprietary rights in any form inand to the Software and Documentation, including, but not limited to, all rights in patents, patentapplications, inventions, copyrights, trademarks, trade secrets, trade names, and other proprietary rightsin or relating to the Software and Documentation. No rights are granted to End-User Customer under thisAgreement by implication, estoppel or otherwise, except for those rights which are expressly granted toEnd-User Customer in this End-User License Agreement. All intellectual property developed, originated,or prepared by Symbol Technologies in connection with providing the Software, Products, Documentationor related services remains vested exclusively in Symbol Technologies, and End-User Customer will nothave any shared development or other intellectual property rights.
58 AP-7562 Access Point 6. CONFIDENTIALITY 6.1 End-User Customer acknowledges that the Software contains valuable proprietary information and tradesecrets and that unauthorized dissemination, distribution, modification, reverse engineering,disassembly or other improper use of the Software will result in irreparable harm to SymbolTechnologies for which monetary damages would be inadequate. Accordingly, End-User Customer willlimit access to the Software to those of its employees and agents who need to use the Software forEnd-User Customer’s internal business 7. MAINTENANCE AND SUPPORT 7.1 No maintenance or support is provided under this End-User License Agreement. Maintenance or support,if available, will be provided under a separate Software maintenance and support agreement. 8. LIMITED WARRANTY AND LIMITATION OF LIABILITY8.1 Unless otherwise specified in the applicable warranty statement, the Documentation or in any othermedia at the time of shipment of the Software by Symbol Technologies, and for the warranty periodspecified therein, for the first 120 days after initial shipment of the Software to the End-User Customer,Symbol Technologies warrants that the Software, when installed and/or used properly, will be free fromreproducible defects that materially vary from its published specifications. Symbol Technologies doesnot warrant that End-User Customer’s use of the Software or the Products will be uninterrupted orerror-free or that the Software or the Products will meet End-User Customer’s particular requirements.8.2 SYMBOL TECHNOLOGIES’ TOTAL LIABILITY, AND END-USER CUSTOMER’S SOLE REMEDY, FOR ANYBREACH OF THIS WARRANTY WILL BE LIMITED TO, AT SYMBOL TECHNOLOGIES’ OPTION, REPAIR ORREPLACEMENT OF THE SOFTWARE OR PAYMENT OF END-USER CUSTOMER’S ACTUAL DAMAGES UPTO THE AMOUNT PAID TO SYMBOL TECHNOLOGIES FOR THE SOFTWARE OR THE INDIVIDUALPRODUCT IN WHICH THE SOFTWARE IS EMBEDDED OR FOR WHICH IT WAS PROVIDED. THISWARRANTY EXTENDS ONLY TO THE FIRST END-USER CUSTOMER; SUBSEQUENT TRANSFEREES MUSTACCEPT THE SOFTWARE “AS IS” AND WITH NO WARRANTIES OF ANY KIND. SYMBOLTECHNOLOGIES DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE IMPLIEDWARRANTIES OF MERCHANTABILITY, NON-INFRINGEMENT, AND FITNESS FOR A PARTICULARPURPOSE. 8.3 IN NO EVENT WILL SYMBOL TECHNOLOGIES BE LIABLE FOR SPECIAL, INCIDENTAL ORCONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOSS OF USE, TIME OR DATA,INCONVENIENCE, COMMERCIAL LOSS, LOST PROFITS, OR SAVINGS, TO THE FULL EXTENT SUCH MAY
Installation Guide 59BE DISCLAIMED BY LAW, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THELIMITATIONS IN THIS PARAGRAPH WILL APPLY NOTWITHSTANDING ANY FAILURE OF ESSENTIALPURPOSE OF ANY LIMITED REMEDY.9. TERM AND TERMINATION 9.1 Any use of the Software, including but not limited to use on the Products, will constitute End-UserCustomer’s agreement to this End-User License Agreement. End-User Customer’s right to use theSoftware will continue for the life of the Products with which or for which the Software andDocumentation have been provided by Symbol Technologies, unless End-User Customer breaches thisEnd-User License Agreement, in which case this End-User License Agreement and End-User Customer’sright to use the Software and Documentation may be terminated immediately by Symbol Technologies. Inaddition, if Symbol Technologies reasonably believes that End-User Customer intends to breach thisEnd-User License Agreement Symbol Technologies may, by notice to End-User Customer, terminateEnd-User Customer’s right to use the Software.9.2 Upon termination, Symbol Technologies will be entitled to immediate injunctive relief without provingdamages and, unless End-User Customer is a sovereign government entity, Symbol Technologies willhave the right to repossess all copies of the Software in End-User Customer’s possession. Within thirty(30) days after termination of End-User Customer’s right to use the Software, End-User Customer mustcertify in writing to Symbol Technologies that all copies of such Software have been returned to SymbolTechnologies or destroyed.10. UNITED STATES GOVERNMENT LICENSING PROVISIONS10.1 This Section applies if End-User Customer is the United States Government or a United StatesGovernment agency. End-User Customer’s use, duplication or disclosure of the Software andDocumentation under Symbol Technologies’ copyrights or trade secret rights is subject to the restrictionsset forth in subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights clauseat FAR 52.227-19 (JUNE 1987), if applicable, unless they are being provided to the Department ofDefense. If the Software and Documentation are being provided to the Department of Defense, End-UserCustomer’s use, duplication, or disclosure of the Software and Documentation is subject to the restrictedrights set forth in subparagraph (c)(1)(ii) of the Rights in Technical Data and Computer Software clause atDFARS 252.227-7013 (OCT 1988), if applicable. The Software and Documentation may or may notinclude a Restricted Rights notice, or other notice referring to this End-User License Agreement. Theprovisions of this End-User License Agreement will continue to apply, but only to the extent that they are
60 AP-7562 Access Point consistent with the rights provided to the End-User Customer under the provisions of the FAR and DFARSmentioned above, as applicable to the particular procuring agency and procurement transaction.11. GENERAL11.1 Copyright Notices. The existence of a copyright notice on the Software will not be construed as anadmission or presumption that public disclosure of the Software or any trade secrets associated with theSoftware has occurred. 11.2 Compliance with Laws. End-User Customer acknowledges that the Software is subject to the laws andregulations of the United States and End-User Customer will comply with all applicable laws andregulations, including export laws and regulations of the United States. End-User Customer will not,without the prior authorization of Symbol Technologies and the appropriate governmental authority ofthe United States, in any form export or re-export, sell or resell, ship or reship, or divert, through direct orindirect means, any item or technical data or direct of indirect products sold or otherwise furnished toany person within any territory for which the United States Government or any of its agencies at the timeof the action, requires an export license or other governmental approval. Violation of this provision is amaterial breach of this Agreement.11.3 Third Party Beneficiaries. This End-User License Agreement is entered into solely for the benefit ofSymbol Technologies and End-User Customer. No third party has the right to make any claim or assertany right under this Agreement, and no third party is deemed a beneficiary of this End-User LicenseAgreement. Notwithstanding the foregoing, any licensor or supplier of third party software included inthe Software will be a direct and intended third party beneficiary of this End-User License Agreement.11.4 Waiver. No waiver of a right or remedy of a Party will constitute a waiver of another right or remedy ofthat Party. 11.5 Assignments. Symbol Technologies may assign any of its rights or sub-contract any of its obligationsunder this End-User License Agreement or encumber or sell any of its rights in any Software, withoutprior notice to or consent of End-User Customer. 11.6 Causes of Action. End-User Customer must bring any action under this End-User License Agreementwithin one year after the cause of action arises except that warranty claims must be brought within theapplicable warranty period. 11.7 Entire Agreement and Amendment. This End-User License Agreement contains the parties’ entireagreement regarding End-User Customer’s use of the Software and may be amended only in a writingsigned by both parties, except that Symbol Technologies may modify this End-User License Agreement asnecessary to comply with applicable laws and regulations.
Installation Guide 6111.8 Governing Law. This End-User License Agreement is governed by the laws of the the State of Delawarein the United States to the extent that they apply and otherwise by the internal substantive laws of thecountry to which the Software is shipped if End-User Customer is a sovereign governmental entity. Theterms of the U.N. Convention on Contracts for the International Sale of Goods do not apply. In the eventthat the Uniform Computer information Transaction Act, any version of this Act, or a substantially similarlaw (collectively “UCITA”) becomes applicable to a Party’s performance under this Agreement, UCITAdoes not govern any aspect of this End-User License Agreement or any license granted under thisEnd-User License Agreement, or any of the parties’ rights or obligations under this End-User LicenseAgreement. The governing law will be that in effect prior to the applicability of UCITA.11.8 Dispute Resolution. Unless End-User Customer is a sovereign governmental entity, any dispute arisingfrom or in connection with this End-User License Agreement shall be submitted to the sole and exclusiveforum of the state and federal courts sitting in New Castle County, Delaware (the "Delaware Courts"),and each Party irrevocably submits to the jurisdiction of the Delaware Courts for the litigation of suchdisputes. Each Party hereby irrevocably waives, and agrees not to assert in any suit, action or proceedingbrought in the Delaware Courts, any claim or defense that the Party is not subject to the jurisdiction ofthe Delaware Courts, that the Delaware Courts are an inconvenient forum, or that the Delaware Courtsare an improper venue.
62 AP-7562 Access Point 8 AP-7562 Series ROHS Compliance本表格依据 SJ/T 11364 的规定编制。O:表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限量 要求以。X:表示该有害物质至少在该部件的某一均质材料中的含量超出GB/T 26572 规定 的限量要求。(企业可在󰢛处，根据实际情况对表中打×的技术原因进 行进一󰢜说明。）This table was created to comply with China RoHS requirements.
Installation Guide 63
Zebra Technologies CorporationLincolnshire, IL 60069 USAZebra and the Zebra head graphic are registered trademarks of ZIH Corp. The Symbol logo is a registered trademark ofSymbol Technologies, Inc., a Zebra Technologies company.© 2015 Symbol Technologies, Inc.MN001745A01 Revision A April 2015

Navigation menu