Suprema BLNOC BioLite-NET User Manual

Suprema Inc. BioLite-NET

User manual

www.supremainc.comBioLite NETInnovative Fingerprint TerminalUser Guide (ver 1.0)User guide( ver 1.0 )
Product ContentsBasic ContentsProduct ContentsProduct ContentsEE--ringringMain BodySub bracket DefaultWall-mounting metal bracketMain BodySub b c e(optional) Default zRecommended power supply12V ±10%, at least 2500mA for BioLite-NETShrinking Tubealone installation.Comply with standard IEC/EN 60950-1(CE Certification).To share the power with other devices, use a power supply with higher current ratings.2ⒸCopyright 2008 Suprema Inc.Before Start12V power adaptor(optional)Shrinking Tube
Cable spec.PIN POWER + 485 WIRE1POWER (12Vd )RED1POWER + (12Vdc)RED2 POWER GND BLACK3 485 GND WHITE(Black String)4 485 + BLUE(Black String)5 485 - YELLOW(Black String)Power & 485PINRELAYWIRERelayPINRELAYWIRE1 NORMAL CLOSE ORANGE(White String)2 COMMON GREEN(White String)3 NORMAL OPEN GRAY(White String)PIN SWITCH WIREEthernet1ERX - YELLOW2ERX + BLUE3ETX - ORANGE4ETX + PINKSwitch & WiegandPIN SWITCH&WIEGAND WIRE1WGND BLACK2WDATA 1 WHITE3WDATA 0 GREEN4GND GRAY5SWIN 1 BROWN6GND GRAY7SWIN 0 PURPLE3ⒸCopyright 2008 Suprema Inc.Before Start
Power Connection Recommended power supplyz12V ±10%, at least 1000mA.zTo share the power with other devices, use a power supply with higher current ratings.4ⒸCopyright 2008 Suprema Inc.
Relay Connection – Fail safe lock5ⒸCopyright 2008 Suprema Inc.
Relay Connection – Fail secure lock6ⒸCopyright 2008 Suprema Inc.
Relay Connection - Automatic door7ⒸCopyright 2008 Suprema Inc.
Door switch connectionBioLite NET(1)SW0Input(PURPLE)1Door Status(1) SW0 Input (PURPLE)(2) SW0 GND (GRAY)(3) SW1 Input (BROWN)(4) SW1 GND (GRAY)4Request To qExit8ⒸCopyright 2008 Suprema Inc.
Switch connection (Alarm, Emergency switches)9ⒸCopyright 2008 Suprema Inc.
RS485 connection for host communication10ⒸCopyright 2008 Suprema Inc.Before Start
RS485 connection for Secure I/O(2) Power GND (Black)(1) Power 12V (Red)Power(2) Power GND (Black)(1) Power 12V (Red) PowerBioLite NET (Master) BioLite NET (Slave)*Eblt iti(5) TRX- (Yellow)(4) TRX+ (Blue)(3) Signal GND (White)()()(5) TRX- (Yellow)(4) TRX+ (Blue)(3) Signal GND (White)*Enable termination (ti lNt1)TRX-TRX+TRX GND*Enable termination (optional, see Note1)Secure I/OTRX-TRX+TRX GNDSecure I/O...(optional, see Note1)As short as possible (Note 2)Important Notes1. For bus termination, only the devices at both ends of the bus should be terminated. Tbltiti thRS232485tftth t’lTo enable termination on the RS232-485 converter, refer to the converter’s manual.2. The stubs should be as short as practical11ⒸCopyright 2008 Suprema Inc.
Installation Reference - Stand alone12ⒸCopyright 2008 Suprema Inc.
Installation Reference – Using Secure I/O, 2 doorRTE switchSwitch 0Switch 0RTE switchSecure I/ODoor 1Relay 0Door0InternalRelay RS485Door 0Door StatusSwitch 1Door Status Switch 113ⒸCopyright 2008 Suprema Inc.
14ⒸCopyright 2008 Suprema Inc.
Installation Reference – Using RFID carditem contentModel BioLite-NET(BLN-OC)()Transmit 13.56MHzReceive 13.56MHzModulation ASKCommunication Single propagationChannel Single channelMode 1:1 Using RFID card (13.56MHz = Mifare model only)zIn case 1:1 mode is set as RF Card zIf the 1:1 mode is set as Card Only, user can access just by placing the card to BioLite-NET without any additional procedure. 15ⒸCopyright 2008 Suprema Inc.
Installation Reference – LAN Secure I/ORelay 0RS485RTE switchSwitch 0Network hub EthernetI/ODoor 1Door StatusSwitch 1If you select Network on initial UI menu, Network Setup menus appear on the display. If you select TCP/IP on network menu, following menus appear on the display. zSetting : Disable/EthernetzUsed when connected to PC via Ethernet using RJ45 connector on the rear of the device. LAN TYPEzSetting : 1/4/8/16zMax number of clients that can access the device at the same time.zSetting : Use/not use.zIt sets Use or Not Use of SSL between the TEST UI and BioLiteNETMax connSSLzIt sets Use or Not Use of SSL between the TEST_UI and BioLite-NET.zSetting : Use/not usezUsing DHCP, you can receive IP address and other necessary setting from server automatically. zCheck whether an appropriate DHCP server is available in your network environment before use. DHCP16ⒸCopyright 2008 Suprema Inc.zWithout using DHCP, IP address, gateway, and subnet need to be entered manually. Inquire necessary settings to network administrator. IP Address, gateway, subnet
Electrical SpecificationMin. Typ. Max. NotesPowerVoltage (V)10 81213 2Use regulated DC power adaptor onlyVoltage (V)10.81213.2Use regulated DC power adaptor onlyCurrent (mA) - 250RTC BatteryVoltage (V) 2.7 3 3.3 Lithium-ion rechargeable batteryCurrent (mAH) -11Switch InputVIH (V) -TBD -VIL(V)-TBDVIL(V)TBDPull-up resistance (Ω)- 4.7k - The input ports are pulled up with 4.7k resistorsTTL/Wiegand OutputVOH (V) -5 -VOL (V) -0.8 -Pull-up resistance (Ω)-4.7k -The outputs ports are open drain type, pulled up with 4.7k resistors internallyRelaySwitching capacity (A) -- 10.330V DC125V ACSwitching power (resistive) --30W37.5VADCAC17ⒸCopyright 2008 Suprema Inc.Switching voltage (V) --110125DCAC
18ⒸCopyright 2008 Suprema Inc.
TroubleshootingFingerprint can not be read well or it takes too long.zCheck whether a finger or fingerprint sensor is stained with sweet, water or dustggp ,zRetry after wiping off finger and fingerprint sensor with dry towel.zIf a fingerprint is way too dry, blow on the finger and retry.Fingerprint is entered but authorization keeps failing.zCheck whether the user is restricted by door zone or time zonezCheck whether the user is restricted by door zone or time zonezInquire of administrator whether the enrolled fingerprint has been deleted from the device for some reason Authorized but door is not opened.zCheck whether the time is set as lock timezCheck whether the time is set as lock time.zCheck whether an antipass back mode is in use. In antipass back mode, only who entered can exit.Device doesn’t operate though power is connected.zCheck whether a device and a bracket is well connected to each other. If not, a tamper switch is activated and the device doesn’tworkactivated and the device doesn t work.RTC Battery caution.zRisk of explosion if battery is replaced by an incorrect type.zDispose of used batteries according to the instructions.19ⒸCopyright 2008 Suprema Inc.
FCC Rules20ⒸCopyright 2008 Suprema Inc.
Tel : 82-31-710-2400Fax : 82-31-783-450621ⒸCopyright 2008 Suprema Inc.

Navigation menu