Suprema BEPMTC FINGERPRINT SYSTEM User Manual 1 of 2

Suprema Inc. FINGERPRINT SYSTEM 1 of 2

Contents

User manual 1 of 2

(ver1.0)Installation GuideIP based Fingerprint Access Controlwww.supremainc.com
2ⒸCopyright 2007Suprema Inc.ContentsSafety precautions 3Basics of fingerprint recognition 5How to place a finger 6Product Contents 8Front Side 10Bottom and Back Side 11Product Dimension 12Cables and Connectors 13Installation of Wall-mount Bracket 14Power Connection 15Ethernet Connection 16RS485 Connection 18Relay Connection 20Digital Input Connection 23WiegandOutput 25Installation Reference 26Electrical Specification 29Troubleshooting 30Device cleaning 31FCC Rules 32
3ⒸCopyright 2007Suprema Inc.Safety precautionsnThe list below is to keep user’s safety and prevent any loss. Please read carefully before use.Do not install the device in a place subject to direct sun light, humidity, dust or soot.Do not place a magnet near the product. Magnetic objects such as magnet, CRT, TV, monitor or speaker may damage the device.Do not place the device next to heating equipments.Be careful not to let liquid like water, drinks or chemicals leak inside the device. Clean the device often to remove dust on it.In cleaning, do not splash water on the device but wipe it out with smooth cloth or towel.
4ⒸCopyright 2007Suprema Inc.Safety precautionsnThe list below is to keep user’s safety and prevent any loss. Please read carefully before use.Do not drop the device. Do notdamage the device. Do not disassemble, repair oralterthe device.Do not let children touch the devicewithout supervision.Do not use the device for any other purpose than specified.Contact your nearest dealer in case of a trouble or problem.
5ⒸCopyright 2007Suprema Inc.Basics of fingerprint recognitionnWhat is fingerprint recognition?lFingerprint is an individual’s own biometric information and does not change throughout his/her life. Fingerprint recognition is a technology that verifies or identifies an individual using such fingerprint information.lFree from the risk of theft or loss, fingerprint recognition technology is being widely used in security systems replacing PIN or cards. nProcess of fingerprint recognitionlFingerprint consists of ridges and valleys. Ridge is a flow of protruding skin in a fingerprint while valley is a hollow between two ridges. Each individual has different pattern of ridges and valleys and finger recognition makes use of such originality and uniqueness of these patterns.lFingerprint sensor generates 2-dimentional fingerprint image using different technology. According to the sensing technology, fingerprint sensors are classified into optical, capacitive, or thermal. lFingerprint template is a collection of numeric data representing the features of a fingerprint. Fingerprint templates are saved inside the memory of BioStation and used for identification. nSecure way to protect personal information lTo avoid privacy concern, Suprema’s fingerprint products do not save fingerprint images itself. Itis impossible to reconstruct a fingerprint image from a fingerprinttemplate which is just numeric data of the features of a fingerprint.
6ⒸCopyright 2007Suprema Inc.How to place a fingerSuprema’sfingerprint products show an outstanding recognition performance regardless of the user’s fingerprint skin condition or the way of fingerprint positioning. However, following tips are recommended to get more optimal fingerprint recognition performance.nSelect a finger to enrolllIt is recommended to use an index finger or a middle finger. lThumb, ring or little finger is relatively more difficult to place in a correct position.nHow to place a finger on a sensorlPlace a finger such that it completely covers the sensor area with maximum contact. lPlace core part of a fingerprint to the center of a sensor.§People tend to place upper part of a finger.§The core of a fingerprint is a center where the spiral of ridgesis dense. §Usually core of fingerprint is the opposite side of the lower part of a nail. §Place a finger such that the bottom end of a nail is located at the center of a sensor.lIf a finger is placed as in the right picture, only a small areaof a finger is captured. So it is recommended to place a finger as shown in the left picture.
7ⒸCopyright 2007Suprema Inc.How to place a fingernTips for different fingerprint conditionslSuprema’sfingerprint products are designed to scan fingerprint smoothly regardless of the conditions of a finger skin. However, in case a fingerprint is not read well on the sensor, please refer to the followings tips. §If a finger is stained with sweat or water, scan after wiping moisture off.§If a finger is covered with dust or impurities, scan after wiping them off.§If a finger is way too dry, place after blowing warm breath on the finger tip.nTips for fingerprint enrollmentlIn fingerprint recognition, enrollment process is very important. When enrolling a fingerprint, please try to place a finger correctly with care. lIn case of low acceptance ratio, the following actions are recommended.§Delete the enrolled fingerprint and re-enroll the finger.§Enroll the same fingerprint additionally.§Try another finger if a finger is not easy to enroll due to scaror worn-out.lFor the case when an enrolled fingerprint cannot be used due to injury or holding a baggage, it is recommended to enroll more than two fingers per user.
8ⒸCopyright 2007Suprema Inc.Product ContentsnBasic ContentsBioEntryPlus Wall-mounting metal bracketWall mounting screws –2 ea Star-shaped screwsStar-shaped small wrench3 pin, 4 pin, 5 pin, 7pincables –each1 eaSoftware CD
9ⒸCopyright 2007Suprema Inc.Product ContentsnOptional accessoriesUSB fingerprint scanner for enrollment on PC12V power adaptor Plastic standSecure I/O
10ⒸCopyright 2007Suprema Inc.nFrontFront SideRF card reading partPlace an RF card over the pictureLEDDisplay current status using seven different colorsFingerprint sensing partPlace a finger on a sensor surfaceLED Status per ColorlGreen : Authorization SuccesslRed : Authorization FaillPink : On Processing lFlicker Blue/Sky-Blue Color per 2sec : NormallFlicker Red/Pink Color per 2sec : LockedlFlicker Blue/Red Color per 2sec : Initialized Time due to the Internal Battery DischargelFlicker Blue/Yellow Color per 2sec : DHCP FaillFlicker Red Color per 2sec : Failed. Please contact to your distributor or SupremalFlicker Yellow Color per 2sec : Waiting InputlFlicker Yellow Color per 1sec : Receiving IP Address from DHCP server
11ⒸCopyright 2007Suprema Inc.Bottom and Back SidenBottomnBackStar-shaped screw hole for fixing a body to a metal bracket3 pin connector –wiegandoutput5 pin connector –power and RS4854 pin connector –ethernet(TCP/IP)7 pin connector –digital input and relay outputDIP switch –RS485 termination setting(Refer to “RS485 Connection”pages for details)

Navigation menu