Sunitec Enterprise BH004 Bluetooth Mono Headset User Manual Print

Sunitec Enterprise Co., Ltd. Bluetooth Mono Headset Print

Manual

4. Charging Your Bluetooth Headset IMPORTANT: (1) Charging indication will be delayed for a few minutes if the headset has not been used for a long period time or the battery is drained.(2) To prolong durability of battery, it is recommended to charge the headset whenever a low battery signal is encountered. When battery becomes low, the LED will flash red every 3 seconds. Under a low battery condition, if headset is continuously used, it will decrease the durability of battery as well as the standby time. This causes a longer charge time than the normal 2 hours and the headset will power off.(3) The red LED will flash on while charging, and blue LED will flash on whencharging is completed.The Bluetooth Headset comes with a built-in rechargeable battery. Prior to using the headset, it is recommended to charge the battery fully for the first time. Normal full charge time is 2 hrs. (approx.)5. Turning ON/OFF the HeadsetPOWER ON: When the headset is in off mode, press and hold the “MFB” for 3 seconds until you hear a short beep. The blue LED will flash 5 times, and then the headset will automatically re-connect to the last connected mobile phone.POWER OFF: When headset is in standby mode, press and hold the “MFB” button for 3 seconds until you hear a short beep. The red LED will flash 5 times before turning off.6. PairingPrior to using the headset for the first time, you must pair it with a Bluetooth-enabled mobile phone. The steps below describe pairing instructions for a typical Bluetooth-enabled mobile phone.(1) Place the headset and mobile phone no more than 1 meter apart.(2) Ensure the headset is in OFF mode.(3) Press and hold the “MFB” button for 6 seconds until the red and blue LED flashes. It is now ready for pairing.(4) Activate the Bluetooth function on your mobile phone. (Refer to your mobile phone owner’s manual).(5) Select : ”BT Headset” from the list.(6) Enter the pre-programmed code “0000” and press “OK” to pair the headset and the phone. When pairing is completed, the red LED will stop flashing and the headset is now in standby mode with the blue LED flashing every 3 seconds.-02-CRC#: 5279036Instruction ManualBefore using this product, read this manual carefully and retain itfor future reference.1. About Bluetooth Technology Bluetooth wireless technology is set to revolutionize the personal connectivity by providing freedom from wired connections-enabling links and connectivity between notebook/laptop, mobile phones,portable handheld devices and other Bluetooth enabled devices within10 meters. Utilizing global sound & digital data 2.4GHz ISM transmission, it makes global communication in the way you’ve neverdreamed of! 2. Getting to Know Your Bluetooth Headset To use your Bluetooth Headset, please follow these simple steps:(1) Charge your Headset. Prior to using the Headset, it is recommended to charge the battery fully for the first time. Normal full charge time is 2 hrs. (approx.)(2) Place your Headset and a Bluetooth-enabled mobile phone within 1 meter for pairing.(3) Ensure your Headset and mobile phone is placed within 10 meters Bluetooth sensing distance.(Obstruction could cause shorter sensing distance.) 3. Appearance and Function (1) Speaker(2) Microphone(3) Charging Socket(4) Multi-Function Button (MFB)(5) Volume Increase (V+)(6) Volume Decrease (V-) -01-(3)(1)(5)(6)(2)(2)(4) (7) Press “Return” to go back to your mobile phone’s main menu. Place the mobile phone and headset within 10 meters for recommended sensing distance. NOTE : If the pairing is not completed within 2 minutes after pairingmode is activated, the headset will power off automatically. You will have to repair the headset using the steps above.9. Using the Headset(1) ANSWERING CALL When receiving a phone call, press the “MFB” button to answer the call.(2) ENDING CALL Press the “MFB” button to end a call.(3) REJECT CALL When you hear the ringing tone, press and hold the “MFB” button for 3 seconds to reject the call.(4) VOICE DIALIf your mobile phone is voice dialing enabled, in standby mode, press the “MFB” button and say the voice tag after you hear a beep.NOTE : Please make sure to record voice tag into the mobile phone before using voice dial function. Functionality varies depending on the mobile phone models. (Refer to your mobile phone owner’s manual.)-03-7. Connection/Link between Headset and Mobile PhoneAfter pairing is completed, headset is always under standby mode. Before you place or answer a call, if the headset icon is not shown on phone screen, please follow the steps below to activate the Bluetooth connection/link through your mobile phone or headset until the headset icon is on the screen.(1) On phone: Select the “BT Headset” from the paired list on your phone screen.(2) On headset: Short press “MFB” and select “Accept” on phone screen to accept connection.8. Disconnection between Headset and Mobile PhoneWhen you need to connect your headset with another Bluetooth-enabled mobile phone, please follow the steps below to disconnect the headset with the pre-paired mobile phone.(1) Power off the Headset.(2) Select “Disconnecting” on the Bluetooth device list of your mobile phone to remove the connection.Note: When losing the connection/link, the headset will be automatically power off in 10 minutes. The blue LED will flash twice in every 3 seconds when the headset is not connected with mobile phone.Manufactured for your Military Exchanges©2012 ExchangeP.O.BOX 660202Dallas, TX 75266-0202Printed in Chinawww.shopmyexchange.com-07-14. Product SpecificationsBluetooth Compliance: Bluetooth V2.1 + EDR specificationsOperating Frequency Band: 2.4 GHz ~ 2.48 GHz unlicensed ISM bandOutput Power: Class 2 Power Output, up to 10 meters Support Profiles: HSP and HFP1.5 profilesSupport Multiple Paired Device: Up to 8 Bluetooth Phone can be paired Stand-by Time: Up to 150 hoursTalk Time: Up to 4 hoursBattery Charging Time: About 2 hoursCharger Voltage: DC5.0V, 300mABattery: 85 mAH, (Rechargeable Lithium-ion battery) (5) LAST NUMBER RE-DIALING In standby mode, press the “MFB” button twice for last number redial.(6) ADJUSTING THE VOLUME During a call, press the “V+” or “V-” buttons repeatedly until you reach the desired volume level.(7) MUTE & UN-MUTEa. Mute: During a call, press and hold the “V-” button for 3 seconds to mute the headset. The red LED will flash on during mute mode.b. Un-Mute: press and hold the “V-” button 3 seconds to un-mute the headset.(8) TRAN SFERRING CALLSa. Headset to Mobile Phone: During a call, press and hold the “V+” button for 3 seconds. The call is routed to your mobile phone.b. Mobile Phone to Headset: Press and hold the “V+” button for 3 seconds to route the call to the headset.(9) HOLD THE CALL During a call, press the “MFB” button twice to hold the phone call. Press “MFB” button twice again to resume conversation.(10) Answer the Second Calla. When receiving a second call, press “MFB” button twice to hold the first call on line and answer the second call.b. When receiving a second call, press “MFB” button once to end the first call and answer the second call.(11) Reject the Second Call When receiving a second call, press and hold the “MFB” button for 2 seconds to reject the second call.(12) Switch Between 2 Phone Callsa. When having 2 calls on the line, press “MFB” button twice to switch between these 2 phone calls.b. When having 2 calls on the line, press “MFB” button once to end the first call and stay with the second call.10. MultiPoint Feature (1) Activate Multipoint ConnectionThe default setting of headset’s multipoint function is off. Please activate the multipoint function for connecting with 2 mobile phones in the same time.-04-a. Multipoint On: Under standby mode, press and hold “V+” button for 6 seconds until you hear a beep. After turn on the multipoint function, the headset will automatically connect to the last 2 mobile phones that has been paired before.(2) Multipoint Pairinga. FIR ST MOBILE PHONE : Pair the headset with one of the Bluetooth-enabled mobile phones.b. SECON D MOBILE PHONE : Power off the headset. Press and hold the “MFB” button for 6 seconds to enter pairing mode again to pair and connect with the second mobile phone.c. Connect with the first paired mobile phone to the headset.(3) Multipoint Connection/Link with 2 Mobile Phones After the multipoint function is activated, please follow the steps below to connect with 2 Bluetooth enabled mobile phones at the same time.a. When power on the headset, it will automatically search and connect the last 2 mobile phones that have been connected before.b. In standby mode, press and hold “V+” button for 3 seconds until you hear a beep, then the headset will automatically connect the last 2 mobile phones that have been connected before.(4) Using the Secondary Mobile Phone through HeadsetWhen connected with 2 Bluetooth mobile phones, the first connected one is primary phone that can use “MFB” button for voice dial and redial. The second connected phone is the secondary phone that will use “V+” button for voice dialing and redialing.a. VOICE DIAL : Press “V+” button once to activate the secondary phone’s voice dialing function.b. RE-DIALING : Press “V+” button twice to redial the last outgoing number of secondary phone.NOTE :1. When the headset is in Multipoint off mode and connected with only one mobile phone, it can also enter voice dial function by pressing the “V+” button once, or make last outgoing number re-dialing by pressing “V+” button twice.-05-b. Multipoint Off: Under standby mode, press and hold “V-” button for 6 seconds until you hear a beep. The headset will turn off the multipoint function and power off automatically. When power on the headset again, it will only connect to the last connected Bluetooth device.11. Low Voltage Protection of BatteryWhen the voltage of the battery is decreased to 3.3 V, the red LED will flash every 3 seconds, and the headset will be powered off automatically when the voltage is less than 3.0 V.12. Restore to Default SettingFollow the steps below to reset the headset to its original setting and remove all previous pairings and connections.(1). Ensure the headset is under standby mode.(2). Press and hold both of “V+” and “V-” buttons for 6 seconds until the red LED and blue flashes 5 times, then the headset will resume instandby mode. The headset is now back to its original setting.After powering on the headset again, it will enter pairing mode automatically. NOTE S:If the headset is connected with a mobile phone before restoring to originalbefore restoring to originaldefault setting, it will enter pairing mode automatically after restored to default. If the headset is not connected to the mobile phone default setting, it will be in standby mode after restored to default setting.13. LED IndicationHeadset Status LED IndicationPower Off Mode OffPower On Blue LED flash 5 times rapidlyPower Off Red LED flash 5 times rapidlyStandby Mode Blue LED flash once every 3 secondsStandby (Disconnect Bluetooth device) Blue LED flash twice every 3 secondsStandby-Low Voltage Red LED flash once every 3 secondsTalk in progress Blue LED flash once every 6 secondsMute Red LED steady onPairing in progress The red and blue LED flash on alternativelyCharging in progress Red LED steady onCharging completed Blue LED steady on
Please also inform the grantee, that the regulatory text as shown in the manual provided, is not good. The correct content must be as given below. It is important that they correct this before placing the product on the US and Canadian market.FCC Information: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B Digital Device,pursuant to Part 15 of the FCC Rules. These limits are designed to this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the radio or television off and on, the user is encouraged to try to correct interference by one or more of the following measures:‐ Reorient or relocate the receiving antenna.‐ Increase the separation between the equipment and receiver.‐ Connect the equipment into an outlet on another circuit.‐ Consult the dealer or an experienced radio/TV technician for help.Caution: Any changes or modifications not expressly approved by the party responsible forcompliance could void the user's authority to operate this equipment.

Navigation menu