Sunbeam I85B Receiver Unit of the Remote Bedding Control User Manual

Sunbeam Products, Inc. Receiver Unit of the Remote Bedding Control

User Manual

1User ManualWARMING PRODUCTS
IMPORTANT INSTRUCTIONS-DO NOT DESTROYAs with all electrical products, misuse of product or failure toproperly follow the instructions may cause overheating, fire, orpersonal injury. Please read the product label and all of theinstructions before using your warming product.1 Do not use this warming product with an infant, a child, anincapacitated person, a paraplegic, a quadriplegic, a diabetic,one insensitive to heat such as a person with poor bloodcirculation, or anyone who cannot clearly understand theinstructions and/or operate the controls.2 Do not use with damaged cords. Damaged cords can lead tofire. Do not trap, fold, cross, or pinch cords between bed slats,mattress, or springs, or against walls, footboards, or bed frame.3 Do not dry clean this warming product. Cleaning liquid maydamage the insulation of the heating element. Improperlaundering may cause problems with the heating wire which canlead to fire.4 Do not pinch, flex, or expose the heating wire to rubbing. Adamaged heating wire may result in possible overheating or fire.5 Turn off the control for the warming product when not using.6 Keep control away from an open window.7 Do not use pins; they may damage the electric wiring.8 Be sure this blanket/mattress pad/throw is used only on an ACsupply current circuit of 110-120 volts. Do not use with anextension cord.9 Excissive heating may result from folding blanket, when inactual use.10 Keep all dogs, cats, and other pets away from this warmingproduct. This is an electrical appliance that they can damageor be injured by.11 Do not use blanket/mattress pad on a waterbed, sofa, bunkbed, or mechanically adjustable bed and do not use throw on awaterbed, bunkbed, or mechanically adjustable bed.12 Do not use another electronic heating device in conjunctionwith your warming product.13 Use the proper size blanket/mattress pad for your bed. Forexample, use a Twin Size warming blanket on a Twin Size bed.14 If the following Important Instructions are not followed thewarming product will not operate properly.15 If you see the warming product operating improperly, unplug itimmediately and call Sunbeam Consumer Service at the 800number listed under “How to Obtain Warranty Service”.Warnings and Safeguards
1WelcomeThank you for choosing a Sunbeam®warming product.With your purchase you’ve made a real investment inyour comfort and can look forward to staying warm andcozy for many cool days to come.With over 50 years of experience and over 25 millionhouseholds using a Sunbeam®warming product, youcan rest comfortably knowing that Sunbeam®is thebrand to trust…for quality and performance.So get ready for a more restful sleep.Table of contentsDD Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 2Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 3DD Convertible Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 4Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 5DD 2 Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-7Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 6Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 7DD Z Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9Warming Blanket . . . . . . . . . . . . . . . . . . . . . . . 8Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . . 9DD Gradient Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 10Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 11DDY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-13Warming Blanket . . . . . . . . . . . . . . . . . . . . . . 12Mattress Pad . . . . . . . . . . . . . . . . . . . . . . . . . 13LED Throw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14Auto-off feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15Care and cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17-18Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19How to obtain warranty service . . . . . . . . . . . . . 20
2DD RemoteFeatures:• REMOTE CONTROL – sends heat level control commands to the base unitand adjusts the blankets warmth accordingly.• ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD• AUTO-OFF – 10 hour independent auto-off (see page 15)• 10 TEMPERATURE SETTINGS – select your personal comfort• PRE-HEAT – for cozy warmth before bedtime• SOLID STATE – for accurate and consistent heat control• EASY OPERATION – Electronic digital controller for easy operation• EASY GRIP – ergonomic control for easy operation• CORDLESS – no more wires to tangle• AUDIBLE BEEP – when changing heat settings, on/off setting andautomatic programming selections.Pre-heat1To use the preheat feature, simply press the round “On/Off” button andthen press the “Preheat” button. The preheat function will heat the bed fora period of 30 minutes.2To reset the preheat feature, simply press the “On/Off” button OFF.3To turn back ON repeat step1.CAUTION: Do not plug main power cord into the wall outlet until you have completely setup your warming blanket per the instructions.IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK.• Disconnect power cord from wall before detaching control from warming blanket• Always make sure cords are NOT trapped or pinched between bed slats, mattress,springs, against wall, foot board or bed frame. 1Place the warming blanket on the bed with the label side facing outward.2Plug cord into the module at the bottom of the warmingblanket until the plastic hinges click into place. CAUTION:Cord must be COMPLETELY CONNECTED. A risk of fire couldresult from a loose connection.3Run the cord under the bed, not between the mattress and boxsprings. Avoid any tangling or pinching.4Place the base unit on the floor under the bed.5Place the remote control where it is convenient for you.6Plug warming blanket power cord into a 110-120 volt walloutlet. CAUTION: This appliance has a polarized plug (one blade is wider thanthe other). To reduce the risk of electrical shock, this plug is intended tofit only one way into an outlet. If the plug does not fit in the outlet, reversethe plug. Do not attempt to force the plug.62IMPORTANT 2123456Set Up WARMING BLANKET
3Using your Control:1To turn the control on, simply press the “On/Off” button. The backlit display light will illuminate and begin to warmat the comfort setting last used.CAUTION: ALWAYS turn the warming blanket “Off” when not in use.2To turn the warming blanket OFF simply press the “On/Off” a second time.Setting the control side (Queen or King blankets only)The “left” control can operate the left or both sides, and the “right” control can operate the right or both sides. (Ifyou have a Twin or Full size blanket, the remote control operates the entire blanket.) Each person has completecontrol over his/her temperature comfort level for the ultimate in individualized comfort.You can use one remote control to operate both sides of the blanket (both sides of the blanket will have the sameheat level). Or, you can use two remote controls to set separate heat levels for each side of the blanket.Installing the Batteries1Remove the battery compartment door from the back ofthe remote control2Insert three AAA batteries, matching the +and -markingsin the battery compartment to the markings on thebatteries3Replace the battery compartment door4If your blanket has two remote controls, repeat steps 1 – 3 to install batteries in the second remote control.132CAUTION: Do not plug main power cord into the wall outlet until you have completely setup your warming blanket per the instructions.IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAD WILL NOT WORK.• Disconnect power cord from wall before detaching control from warming mattress pad• Always make sure cords are NOT trapped or pinched between bed slats, mattress,springs, against wall, foot board or bed frame. 1Place the warming mattress pad on the bed with the label side facing outward.2Plug cord into the module at the bottom of the warmingmattress pad until the plastic hinges click into place.CAUTION: Cord must be COMPLETELY CONNECTED. A risk of firecould result from a loose connection.3Run the cord under the bed, not between the mattress and boxsprings. Avoid any tangling or pinching.4Place the base unit on the floor under the bed.5Place the remote control where it is convenient for you.6Plug warming mattress pad power cord into a 110-120 voltwall outlet. CAUTION: This appliance has a polarized plug (one blade is wider thanthe other). To reduce the risk of electrical shock, this plug is intended tofit only one way into an outlet. If the plug does not fit in the outlet, reversethe plug. Do not attempt to force the plug.62IMPORTANT 2Set Up WARMING MATTRESS PAD12356WARNING: Changes or modifications to this unit not expressly approved by theparty responsible for compliance could void the user's authority to operateequipment.4
4DD ConvertibleFeatures:• ELECTRONIC DIGITAL CONTROL – for easy setting with backlit LCD• AUTO-OFF – 10 hour independent auto-off (see page 15)• 10 TEMPERATURE SETTINGS – select your personal comfort• PRE-HEAT – for cozy warmth before bedtime• SOLID STATE – for accurate and consistent heat control• EASY OPERATION – Electronic digital controller for easy operation• EASY GRIP – ergonomic control for easy operation• ROOM TEMPERATURE COMPENSATION – • INTERCHANGEABLE TOP – Pre-heat1To use the preheat feature, simply press the round “On/Off” button andthen press the “Preheat” button. The preheat function will heat the bed fora period of 30 minutes.2To reset the preheat feature, simply press the “On/Off” button OFF.3To turn back ON repeat step1.On/OffOn/OffOn/OffOn/OffCAUTION: Do not plug main power cord into the wall outlet until you have completely set upyour warming blanket per the instructions.IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING BLANKET WILL NOT WORK.• Disconnect power cord from wall before detaching control from warming blanket• Always make sure cords are NOT trapped or pinched between bed slats, mattress, springs,against wall, foot board or bed frame. 1Place the warming blanket on the bed with the label side facing outward.2Plug cord into the module at the bottom of the warmingblanket until the plastic hinges click into place. CAUTION:Cord must be COMPLETELY CONNECTED. A risk of fire couldresult from a loose connection.3Run the cord under the bed, not between the mattress and boxsprings. Avoid any tangling or pinching.4For dual control warming blankets, place primary control (labelon back of control) on the same side of the bed as the blanketlabel side.5For single control warming blankets, the control can be placedon either side of the bed.6Plug warming blanket power cord into a 110-120 volt walloutlet. CAUTION: This appliance has a polarized plug (one blade is wider thanthe other). To reduce the risk of electrical shock, this plug is intended to fit only one way into anoutlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug.62IMPORTANT 2123456Set Up WARMING BLANKET
5Using your Control:1To turn the control on, simply press the “On/Off” button. The backlit display light willreset itself by flashing “FF” and then will light showing the previous setting the unitwas set during the last use and will begin to warm.CAUTION: ALWAYS turn the warming blanket/warming mattress pad “OFF” whennot in use.2To turn the warming blanket/warming mattress pad OFF simply press the “On/Off”button.CAUTION: Do not plug main power cord into the wall outlet until you have completely setup your warming blanket per the instructions.IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING MATTRESS PAS WILL NOT WORK.• Disconnect power cord from wall before detaching control from warming mattress pad• Always make sure cords are NOT trapped or pinched between bed slats, mattress,springs, against wall, foot board or bed frame. 1Place the warming mattress pad on the bed with the label side facing outward.2Plug cord into the module at the bottom of the warmingmattress pad until the plastic hinges click into place.CAUTION: Cord must be COMPLETELY CONNECTED. A risk of firecould result from a loose connection.3Run the cord under the bed, not between the mattress and boxsprings. Avoid any tangling or pinching.4For dual control warming mattress pads, place primary control(label on back of control) on the same side of the bed as theblanket label side.5For single control warming mattress pads, the control can beplaced on either side of the bed.6Plug warming mattress pad power cord into a 110-120 voltwall outlet. CAUTION: This appliance has a polarized plug (one blade is wider thanthe other). To reduce the risk of electrical shock, this plug is intended to fit only one way into anoutlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt to force the plug.62IMPORTANT 2Set Up WARMING MATTRESS PADOn/OffOn/OffOn/OffOn/Off123456
6DD 2
7
8DD Z
9
10DD Gradient
11
12DD Y
13
14LED ThrowFeatures:• 3 TEMPERATURE SETTINGS – select your personalcomfort level• SILENT OPERATION – no clicking• SOLID STATE – for accurate and consistent heat control• EASY OPERATION – electronic controller for easyoperation• EASY GRIP – ergonomic control for easy operation• AUTO-OFF – 3 hour independent auto-offUsing your Warming Throw Control:1To turn the throw on simply press the round gray button. Theindicator light will glow, depending on which setting the warmingthrow is set, and the warming throw will begin to warm.CAUTION: ALWAYS turn the warming throw “OFF” anddisconnect the power cord from the outlet when not in use.2To turn the warming throw OFF simply press the round gray buttonthrough the different settings until the temperature setting lightsare not glowing.Auto-off controlCAUTION: Do not plug main power cord into the wall outlet until you have completely setup your warming blanket per the instructions.IF YOU DO NOT FOLLOW THIS SEQUENCE, THE WARMING THROW WILL NOT WORK.• Disconnect power cord from wall before detaching control from warming blanket• Always make sure cords are NOT trapped or pinched between furniture, walls or chairs.ModuleControlPower CordFlag TagThrow CordConnectorThrow CordLabelWhen setting up your warming throw, be sure to follow the stepsbelow in order.1Locate the warming throw’s information label, located near themodule.2Firmly plug the warming throw cord into the module until theplastic hinges on each side click into place. CAUTION: Cord must be COMPLETELY CONNECTED. A risk of firecould result from a loose connection.3Plug warming throw power cord into a 110-120 volt wall outlet.CAUTION: This appliance has a polarized plug (one blade is widerthan the other). To reduce the risk of electrical shock, this plug is intended to fit only oneway into an outlet. If the plug does not fit in the outlet, reverse the plug. Do not attempt toforce the plug.32IMPORTANT 2Set Up WARMING THROW123
15Auto-off featureAuto-off Feature:The “Auto-Off” feature is designed for safety and conservation of energy by automatically turning your warmingproduct off after 10 hours of continuous use.The Auto-off function engages 10 hours from the time the control is turned “On”.For Dual Control:Whichever control is turned On first that controls 10 hour Auto-off feature will be initiated. The controls Auto-off features work independently from each other.To restart after a power failure:Press the “On/Off” or “On” button, the blanket/mattress pad will begin to warm.Note: After a power outage, the “Auto-Off” feature automatically resets the timer.Auto-off Feature for Throw:The “Auto-Off” feature is designed for safety and conservation of energy by automatically turning your warmingproduct off after 3 hours of continuous use.The Auto-off function engages 3 hours from the time the control is turned “On”.(Three Hours forWarming Throw)
16Taking care of your warming product is easy and safe as long as you follow a fewsimple steps.Caution: Always disconnect the power cord and the blanket/mattress pad/throwconnection cord at the connection end before washing. Carefully follow all washinginstructions or your warming product may shrink and possibly cause a fire hazard.DO NOT• DO NOT dry clean your blanket/mattress pad/throw. Dry cleaning solvents may damage the warming element.• DO NOT use bleach or cleaning fluids.• DO NOT use a wringer.• DO NOT iron the blanket/mattress pad/throw.• DO NOT use mothballs or sprays of any kind.• DO NOT turn the blanket/mattress pad/throw on until it is completely dry.Machine Washing1Presoak the blanket/mattress pad/throw for 15 minutes in mild soap and lukewarm water.2Wash in mild soap and lukewarm water on the delicate or gentle cycle in thewasher for two minutes. Remember, do not use bleach.3Rinse in fresh, lukewarm water.4Spin dry in the washing machine. Then gently stretch to its original size. Machine DryingCaution: Do not use commercial dryers or the dryers at your local laundromat. Theyget too hot and would damage the wiring of the warming product.1Preheat the dryer on the low temperature setting for 2 minutes.2Place blanket/mattress pad/throw into the dryer and tumble dry for 10 minutes at a low temperature.3Remove the blanket/mattress pad/throw while it is still damp and gently stretch it to its original size.4Continue to air dry over a clothesline or a shower rod. DO NOT use clothespins.5Warming product must be completely dry before using.Hand Washing1Presoak the blanket/mattress pad/throw for 15 minutes in mild soap andlukewarm water.2Gently squeeze the soap suds through a few times.3Rinse in fresh, lukewarm water.Hand Drying1Gently stretch the blanket/mattress pad/throw back to its original size.2Air dry over a clothesline or hang over a shower rod. DO NOT use clothespins.3Warming product must be completely dry before using.Care and cleaningOF YOUR WARMING PRODUCT
17Frequently asked questionsOF YOUR WARMING PRODUCTQI have heard that some warming products have Electromagnetic Fields (EMFs).What is this?AEMF stands for Electromagnetic Field. This is an electrical field that surrounds anywire that has current flowing along its length. Although several studies have beenconducted to evaluate the impact, EMFs have not been proven to be harmful. Inany event, Sunbeam has reduced the strength of EMFs in its blankets/mattresspads/throws to very low levels.QWhat do I do if my pet chews the cord, I lose my controller, or the controller doesnot operate properly?APlease stop using the warming product immediately. Call our Consumer Servicenumber listed under How to Obtain Warranty Service and ask for instructions onhow and where to send the warming product.QMy control feels warm to the touch: Is this a problem?ANo. The control will feel warm to the touch when functioning properly.QMy warming product doesn’t operate.AFollow instructions on the flag tag. Unplug the system from wall outlet. Check thatthe control is well connected to the module. Plug the power cord into the walloutlet to reset the control. Press “On/Off” or “On” and set at the highest settingand wait 20 minutes. Try this twice. If the system still does not operate, disconnectthe power cord and contact consumer service at the 800 number listed under Howto Obtain Warranty Service.QWho should NOT use the warming blanket, warming mattress pad, or warmingthrow?AThe following people should NOT use the warming blanket, warming mattress pad,or warming throw:• An infant• A child• An incapacitated person• A paraplegic• A quadriplegic• A diabetic• Anyone insensitive to heat• Anyone who cannot clearly understand the instructions and/or operate the controlsQWhat do the Underwriters Laboratories (UL) or (ETL) labels mean? What do eitherof these labels mean about safety of Sunbeam warming products?AUnderwriters Laboratories (UL) develops product safety standards for a large rangeof products and performs independent tests based on these standards. Productstested by UL and which have passed all the safety standards are permitted to bearthe UL label. Intertek Testing Services (ETL) is a certified, independent testingorganization that tests products in accordance with UL safety standards and issuesthe ETL label for those products that meet the relevant UL standards. All Sunbeamproducts are tested to UL standards and bear either the UL or ETL label to indicatethat the product meets or exceeds UL/ETL safety standards for warming products.
18QMy warming blanket/warming mattress pad/warmingthrow doesn’t heat properly.ACheck to make sure the cord is plugged into the moduleand the power cord is firmly connected to the wall outlet.Check that the control is “On”. If the system still fails to heat, try the followingtest to see if it is operating.1Fold the warming blanket, warming mattress pad, or warming throw 3 times over.2Connect the control to the module and plug the power cord into an outlet.3Turn the control to the highest setting and wait five to seven minutes.4Put your hand between the folds and you should feel the blanket/ mattresspad/throw warming. Note: Remember, the warming product is not a heating pad. It will not feel hot to the touch when laid out flat in a normal manner.Caution: Do not continue the test for more than seven minutes. DO NOT attempt tomake any internal adjustments to this appliance. If you have tried all of thesolutions above and the warming product still doesn’t work, stop using itimmediately, disconnect the power cord and contact our consumer service at the 800number listed under How to Obtain Warranty Service.QWhat does “FF” mean on my Electronic Digital Control?AThe digital controls are designed to notify you in the event thata problem has been discovered by flashing “FF” on the display.Follow instructions on the flag tag to reset control. First, checkthe blanket/mattress pad for visual damage. If no visualdamage is found, unplug the system from wall outlet. Checkthat the control is well connected to the module. Plug thepower cord into the wall outlet. Set the control to “On.” If thesystem still does not operate after 2 or 3 times trying to reset, disconnect thepower cord and contact consumer service at 800-892-7684.QWhat does a flashing light mean on my throw LED control or DD Gradient control?AThe throw control and DD Gradient control is designed to notify you in the eventthat a problem has been discovered by flashing the light on the display. Followinstructions on the flag tag to reset control. First, check the blanket/mattresspad/throw for visual damage. If no visual damage is found, unplug the systemfrom wall outlet. Check that the control is well connected to the module. Plug thepower cord into the wall outlet. Set the control to “On.” If the system still does notoperate after 2 or 3 times trying to reset, disconnect the power cord and contactconsumer service at 800-892-7684.QI have experienced some shedding of the fabric fibers of my warmingblanket/warming throw, what do I do?AShedding is normal. If it becomes bothersome, follow the use and care instructionsto wash and dry your warming blanket/warming throw.FFModels DD3, DD2, DDZ, DDWOn/Off
19Sunbeam Products Inc. (“Sunbeam”) warrants that for a period stated below fromthe date of purchase, this product will be free from defects in material andworkmanship. • Warming Blankets branded Sunbeam®Imperial Court™, Elite™, DynastyNights™, SlumberRest Arctic Dawn™, Nordic Dreams™, Winter Oasis™,Basic™ and Northern Illusions™, and Sunbeam®The Blanket with a Brain®willcarry a FIVE year limited warranty.• Warming Blankets branded Sunbeam®Select™ will carry a TWO year limitedwarranty.• Warming Blankets branded Arlington™ will carry a ONE year limited warranty.• Warming Mattress Pads branded Sunbeam®Palace Comfort™, Winter Sunrise™and Midnight Retreat™, SlumberRest®Midnight Sun™ and Glacial Retreat™,and Sunbeam®The Mattress Pad with a Brain®will carry a FIVE year limitedwarranty.• Warming Mattress Pads branded Arlington™ will carry a ONE year limitedwarranty.• Warming Throws branded Sunbeam®Select™, Cuddle-Up™, SlumberRest®Cuddler™, and Sunbeam®The Throw with a Brain® and Sunbeam®AmericanHeritage Collection™ will carry a TWO year limited warranty.• Warming Throws branded Arlington ™, will carry a ONE year warranty.Sunbeam, at its option, will repair or replace this product or any component of theproduct found to be defective during the warranty period. Replacement will be madewith a new or remanufactured product or component. If the product is no longeravailable, replacement may be made with a similar product of equal or greatervalue. This is your exclusive warranty. This warranty is valid for the original retailpurchaser from the date of initial retail purchase and is not transferable. Keep theoriginal sales receipt. Proof of purchase is required to obtain warranty performance.Sunbeam dealers, service centers, or retail stores selling Sunbeam products do nothave the right to alter, modify, or any way change the terms and conditions of thiswarranty. This warranty does not cover normal wear of parts or damage resultingfrom any of the following: negligent use or misuse of the product, use on impropervoltage or current, use contrary to the operating instructions, disassembly, repair oralteration by anyone other than Sunbeam or an authorized service center. Further, thewarranty does not cover Acts of God, or Nature, such as fire, flood, hurricanes andtornadoes. Sunbeam shall not be liable for any incidental or consequential damagescaused by the breach of any express or implied warranty. Except to the extentprohibited by applicable law, any implied warranty of merchantability or fitness for aparticular purpose is limited in duration to the duration of the above warranty. Somestates, provinces or jurisdictions do not allow the exclusion or limitation of incidentalor consequential damages or limitations on how long an implied warranty lasts, sothe above limitations or exclusion may not apply to you. This warranty gives youspecific legal rights, and you may also have other rights that vary from state to stateor province to province.Limited Warranty
20How to obtain warranty service:We’re Here to Help. For any questions you may have about your warming product, pleasecontact Sunbeam Consumer Service: 1-800-892-7684, or write with product questions to:SUNBEAM CONSUMER SERVICEP.O. Box 948389Maitland, FL 32794-8389or visit our web site at: www.sunbeambedding.com.To return your product for repair or replacement: Please attach a tag to the product (do not use pins) that includes your name, address,daytime telephone number, and description of the problem. Please include a copy of theoriginal sales receipt.Carefully package the product. Please use UPS or Parcel Post, with shipping and insuranceprepaid to: SUNBEAM PRODUCTS, INC.Blanket Service StationP.O. Box 469224 Russell DriveWaynesboro, MS 39367DO NOT RETURN THIS PRODUCT TO THE PLACE OF PURCHASE.©2003 Sunbeam® is a registered trademark of Sunbeam Products, Inc.Distributed by Sunbeam Products, Inc., 2381 Executive Center Drive, Boca Raton, FL 33431
PRODUCT REGISTRATION CARDComplete the attached registration card and return todayto receive these 3 important benefits:CONFIRM YOUR WARRANTY:Your prompt product registration confirms your right to the protection availableunder the terms and conditions of your Sunbeam warranty.PROTECT YOUR PRODUCT:We will keep the model number and date of purchase of your new Sunbeamproduct on file to help you refer to this information when necessary.HELP US DEVELOP NEW PRODUCTS:We value your input! Your responses will help us bring you new productsspecifically designed to meet your needs.▲▲▲PLEASE FOLD AND SEAL WITH TAPE BEFORE MAILING. DO NOT STAPLE.PLACEFIRST-CLASSSTAMPHEREPRODUCT REGISTRATION DEPARTMENTPO BOX 44236DENVER CO 80201-4236!802014236365!Please do not send products or othercorrespondence to this address.021 TREGISTER ONLINE AT: WWW.SUNBEAMBEDDING.COMRPOB 9/02
1Initial:State:First name: Last name:Zip code:Address: (number and street)City:Apt number:Date of your birth:Including yourself, what is the total number of people living in your household?(Examples: 01, 02, 03, 04...)Month Day YearDate of birth (month/year) of the other adults and children inyour household:Male Female1.2.  1.2. For your primary residence, do you:1. Own 2. Rent1619172018Month YearMale Female1.2.  1.2. Date of purchase:3Education: (Please check which category applies to you):1. Some high school 3. College degree2. Completed high school 4. Graduate degreeYour marital status: 1. Married 2. SingleYour gender: 1. Male 2. FemaleMonth YearMonth YearMonth YearMonth Day Year 15In the last six (6) months has anyone in your household purchased any of the following items through the mail and/orover the internet? A. Mail B. Internet1. Books/magazines 2. Children’s products 3. Clothes 4. Insurance/financial products 5. Music/video/DVD 6. Travel 7. Other 212224Please fill-out and return this card within 10 days! 021 TI use these credit cards: 1. American Express 4. Visa2. Gas/Retail 5. Other_____________3. Master Card 6. Do not have credit cards23▼▼▼Purchase price: $ .00PLEASE FOLD AND SEAL WITH TAPE BEFORE MAILING. DO NOT STAPLE.62E-mail address: (EXAMPLE: yourname@yourhost.com)1. Yes! I want to receive offers or communications from Sunbeam via e-mail.2. Yes! I want to receive offers or communications that may interest me from other companies via e-mail. I understand this e-mail addressmay be shared with and/or combined with information from other sources.Thank you! We appreciate your responses to this questionnaire. The information you choose to share with us will be used by us and our marketing partners to offer you product information and other communications that may interest you. If you prefer not to be contacted about these special offers, please check here Product purchased: 1. Warming blanket 3. Warming throw2. Warming mattress pad4Style number:5Store where purchased:7Please describe this purchase: 1. A first time purchase2. A replacement to this brand3. A replacement of another brand4. An additional purchase5. Received as a requested gift6. Received as a surprise gift8What do you consider the most important factors influencing your decision to purchase this warming product?1. Color/style 7. Warranty2. Replacement of existing 8. Auto-off feature3. Value for price 9. Large number of heat settings4. Friend/relative’s 10. Energy savingsrecommendation 11. Cold weather5. Advertising 12. Gift for someone else6. Brand name I trust 13. Other_______________10How often do you turn on/plan on turning on your warming product(using its heating capacity)? (Check all that apply)B. Once C. OnceA. Everyday a week a month1. In the winter  2. In the fall  3. In the spring  4. In the summer  11What is the approximate temperature your home thermostat is setto through out the night during winter? 1. Under 55 4. 66-702. 56-60 5. 71-753. 61-65 6. Over 7512How often do you purchase this type of product? 1. Received as a gift 4. Every 4-5 years2. First time purchase 5. Every 6-9 years3. Every 1-3 years 6. Every 10+ years13Which of the following products do you have or plan to own? 1. Warming blanket 3. Electric throw2. Warming mattress pad14We appreciate your responses to this questionnaire and the information you provide will be used by us and our marketing partners to offer you product information and other communication that may interest you. This information in no way will have an effect on your warranty terms.How did you first learn about this product?1. Inside the store 3. News story-public relations2. Advertisement 4. Trusted brand9Someone in my home participates in the following activities:(Check all that apply)1. Crafts 10. Outdoor activities2. Cultural arts/events 11. Own a pet3. Do-it-yourself 12. Personal computing4. Enter sweepstakes/contests 13. Read books5. Finance/investments 14. Self improvement6. Fitness/excercising/jogging 15. Sports7. Gardening 16. Travel8. Gourmet cooking 17. TV shopping9. Home decorating 18. Watch sports on TVRPOB 9/02
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help.

Navigation menu