Spin Master Toys Far East 20418RX2G4 ARH XSM HyprRacrsProAst User Manual Layout 1

Spin Master Toys Far East Ltd. ARH XSM HyprRacrsProAst Layout 1

Users Manual

®1. Open the battery door with ascrewdriver (not included).2. If used batteries are present, remove these batteries from theunit by pulling up on one end ofeach battery.3. Install new batteries as shown inthe polarity diagram (+/-) inside the battery compartment.4. Replace battery door securely.5. Check your local laws and regulations for correct recyclingand/or battery disposal.INSTALLING/REPLACING THE BATTERIESHOW TO CHARGE YOUR HYPER ACTIVES™USING THE REMOTE/CHARGERBatteryCompartmentCoverBatteryCompartment6 x1.5V AAAlkalineBatteries• Remote/charger requires 6 x 1.5VAA alkaline batteries (not included).• Batteries are small objects. • Replacement of batteries must bedone by adults.• Follow the polarity (+/-) diagram inthe battery compartment.• Promptly remove dead batteriesfrom the toy.• Dispose of used batteries properly.• Remove batteries for prolongedstorage.• Only batteries of the same or equivalent type as recommendedare to be used.• DO NOT incinerate used batteries.• DO NOT dispose of batteries in fire,as batteries may explode or leak.• DO NOT mix old and new batteries.• DO NOT mix different types of batteries, i.e.: alkaline/standard(carbon-zinc) or rechargeable batteries.• DO NOT use rechargeable batteries.• DO NOT recharge non-rechargeable batteries.• DO NOT short-circuit the supply terminals.• DO NOT store your car or controllernear heat or in direct sunlight.BATTERY SAFETY INFORMATION12 +YRSEXPERTO ICHG OFF ONCHG OFF ON1. Turn vehicle OFF.2. Turn remote/charger OFF.3. Remove charge plug from storage base.4. Remove charge cable from bottom storage groove.5. Remove vehicle charge port cover.6. Carefully insert the charge plugall the way into the vehicle’scharge port.7. Set the remote/charger switchto CHG.8. The red charging light will turnon and charging will begin whenit starts to flash. After 30 to 50minutes the charging will becomplete and the red chargelight and green power light willboth start to flash.9. When charging is complete, setthe charge switch to OFF.10. Remove charge plug from thevehicle charge port.11. Replace vehicle charge portcover.12. Store charge plug cable and charge plug in remote/charger base.CHG OFF ON15910 11 126 7 82 3 4Remote/ChargerForward/Reverse,Left/Right.1. Turn vehicle ON.2. Turn remote/charger ON.3. Pulling the throttle triggerback moves the vehicleforward. Pushing thethrottle trigger forward,brakes then reverses the vehicle.4. To move the vehicle to theright turn the directionalcontrol to the right.5. To move the vehicle to theleft turn the directionalcontrol to the left.OIO I451CHG OFF ON2NOTE: 1. If the charge light and power light are flashing alternatively whilecharging, there may be a bad cable connection. Check that cable and plugare connected correctly and repeat charging steps 1 to 6.2. The remote control will automatically shut off after idling for about 5 minutes. To reactivate turn off and on.3. When the remote control is in either ON status or CHARGE status andthe green power light is flashing, it means that the battery level is lowand the batteries need to be replaced.Hyper Actives™Contents:• 1 x Hyper Actives™• 4 x Rubber All Terrain Tires• 4 x Rubber Foam Indoor Tires• 1 x Pistol Grip Remote/Charger • 1 x Instruction GuideRollbarInterchangeableRubber and Foam Tiresfor Various TerrainsRubberAll Terrain TiresTMChargePortChargePlugDirectional ControlLeft/RightCHG/OFF/ONSwitchRedCharge LightGreenPower LightTrim DialSLOWFASTVariableSpeed DialThrottle TriggerPull – Proportional SpeedPush – Brake and ReverseINSTRUCTIONS3ForwardReverseRightLeft
Spin Master Ltd., 450 Front Street West, Toronto, ON M5V 1B6 CanadaSpin Master Inc., PMB #10053, 300 International Drive, Suite 100, Williamsville, NY 14221, USASpin Master Toys Far East Limited, Rm #1113, 11/F, Chinachem Golden Plaza, 77 Mody Rd., Tsimshatsui E., Kowloon, HKNorth American Consumer InformationPhone: 1-800-622-8339Email: customercare@spinmaster.comwww.spinmaster.comAir Hogs®, related trademarks & © 2011 Spin Master Ltd. All rights reserved. This product conforms to safety requirements of ASTM F-963 & CHPA. • Please retainthis information for future reference. • Please remove all packaging materials beforegiving to children. • An adult should periodically check this toy to ensure no damageor hazards exist, if so, remove from use. • Children should be supervised during play.• Keep addresses and phone numbers for future reference. • The item inside thispackage may vary from the photographs and/or illustrations. MADE IN CHINA.20043334, 20043335, 20049415, 20049426 REV 0T20418_0001_20043334_NEN_IS_R1TROUBLESHOOTING GUIDEVehicle is slow or will not move.Vehicle does not drive in a straight line.My vehicle and/or remote is dirty.Vehicle is not responding or drivingon it’s own.1. Batteries in the controller need to be replaced if green power light is flashing.2. Vehicle is out of range of controller.3. There is hair or debris stuck in the wheelsor wheel axles.4. Batteries are installed incorrectly.5. Improper surface for vehicle.6. Remote not aimed at vehicle or objects interfering with signal.7. Remote was inactive for 30 seconds or more and turned itself off to preserveyour batteries.Vehicle requires wheel alignment.1. Inappropriate driving surface.2. Dirty hands.1. Using another vehicle remote/charger of the same frequency.2. Infrared interference from another source.1. Replace batteries in the remote with new, fresh batteries.2. Move closer to the vehicle.3. With the vehicle and remote turned off, have an adult carefully remove the hairor debris from the wheels or wheel axles. Remove debris by blowing gently onthe wheel assembly area located on the bottom of the vehicle.4. With the vehicle and remote turned off, have an adult check that the batteriesare installed correctly in the remote.5. Examples of poor play surfaces are thick grass, sand or pebbly areas. Examplesof good play surfaces are tiles, concrete or asphalt.6. Point remote IR at the vehicle. Ensure there are no objects blocking the controller “line of sight” to the vehicle.7. Press the ON/OFF button.Refer to Trim Adjustment guide above.Ensure the remote and vehicle are off. Have an adult remove the batteries first and replace the battery cover. Slightly dampen a clean cloth in water and wipe toyclean. DO NOT IMMERSE IN WATER and DO NOT USE ANY CHEMICALS. Let the toy completely dry before putting batteries back into clean, dry batterycompartment.1. Only use the remote/charger supplied with this vehicle.2. Do not operate vehicle around devices that emit other infrared signals.PROBLEM CAUSE SOLUTIONNOTE: If normal function of the product is disturbed or interrupted, strong electro-magnetic interference may be causing the issue. To reset product, turn itcompletely off, then turn it back on. If normal operation does not resume, move theproduct to another location and try again. To ensure normal performance, changethe batteries, as low batteries may not allow full function.Your Hyper Actives™ is equipped with a Lithium Polymer battery.SPECIAL LIPO BATTERY INSTRUCTIONS:- Never charge battery unattended. - Charge battery in isolated area. Keep away from flammable materials. - Do not expose to direct sunlight. - There is a risk of the batteries exploding, overheating, or igniting. Do not disassemble, modify heat, or short-circuit the batteries. Do not place them in fires or leave them in hot places. - Do not drop or subject to strong impacts. - Do not allow the batteries to get wet. - Only charge the batteries with the specified Spin Master™ battery charger. - Only use the batteries in the device specified by Spin Master™. - Carefully read the instruction guide, and use the batteries correctly. - In the unlikely event of leakage or explosion use sand or a chemical fire extinguisher for the battery.- Batteries must be recycled or disposed of properly.PRODUCT BATTERY REMOVAL INSTRUCTIONS: Internal battery is factory installed,product disassembly and battery removal must be performed by an adult. Do not puncture,cut, tear, compress or deform product during disassembly. Ensure product is turned off,then use a screw driver to remove all screws. Separate product body halves to expose internal electronics. When battery is visible in its entirety use scissors to cut a single batterywire, immediately wrap the cut wire end with tape to isolate it, repeat until all battery wiresare cut and isolated, and the battery is free from the rest of the product. Dispose of batteryin accordance with your local battery recycling or disposal laws. NOTE: Opening of product and/or removal of battery will render product inoperative and voids manufacturerwarranties, dispose of remaining product components in accordance with local laws.VEHICLE TRIM ADJUSTMENTCHANGING TIRES WHEN FINISHED PLAYINGSELF-RIGHTING ROLLBARIf the vehicle is not drivingstraight when you have the directional control wheel in theforward position, use the trimdial to correct the problem.1. If the vehicle turns to theright, slowly turn the trim dialto the left until the vehicledrives straight.2. If the vehicle turns to the left,slowly turn the trim knob tothe right until the vehicledrives straight.Before using yourHyper Actives™ outdoors, carefully remove the rubber foam indoor tires andreplace them with the rubber all terrainoutdoor tires!O ICHG OFF ONVARIABLE SPEED DIALMoving the variablespeed dial to the right will limit the throttle travel decreasing theamount of speedavailable. Moving the dial to the left willactivate full throttleand maximumspeed.SLOWFAST12Turn vehicle OFF.Turn remote/charger OFF.TMA fast, quick turn will causethe vehicle to roll over and theself-righting roll bar will returnthe vehicle onto its wheels!This product complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device mustaccept any interference received, including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digitaldevices pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference to radio communications. This equipment generates,uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. If this toy does causeinterference to radio or television reception (you can check this by turning the toy off and on while listening for the interference), one or more of the following measures may be useful: • Reorient or relocate the receiving antenna • Increase the separation between the toy and the radio or the TV • Consult the dealer or an experienced TV-radio technician for help. NOTE: Changes, adjustments or modifications to this unit, including but not limited to, replacement of any transmitter component (crystal, semiconductor, etc) could result in a violation ofFCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd. or they could void the user’s authority to operate the equipment.CANADIAN Class B statement: This Class B digital apparatus meets all of the requirements of the Canadian Interference-Causing Equipment Regulations.This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received,including interference that may cause undesirable operation. This equipment has been tested and found to comply with the limits for Class B digital devices pursuant to Part 15 of the FCC rules. These limits aredesigned to provide reasonable protection against harmful interference to radio communications. Because this toy generates, uses, and can radiate radio frequency energy, there can be no guarantee thatinterference will not occur. if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this toy does cause interference to radio or television reception(you can check this by turning the toy off and on while listening for the interference), one or more of the following measures may be useful: • Reorient or relocate the receiving antenna • Increase the separationbetween the toy and the radio or the TV • Consult the dealer or an experienced TV-radio technician for help. NOTE:Changes, adjustments or modifications to this unit, including but not limited to, replacement of anytransmitter component (crystal, semiconductor, etc.) could result in a violation of FCC rules under part 15 and/or 95 and must be expressly approved by Spin Master Ltd. or they could void the user’s authority tooperate the equipment.

Navigation menu