Spectrum 450248CBR Value Home Connect, Z-Wave Plus User Manual VHC KW VIVINT ENG indd

Spectrum Brands, Inc. Value Home Connect, Z-Wave Plus VHC KW VIVINT ENG indd

Contents

User Manual

1 / 466455001Rev 01VivintZWave® PlusInstallation and User GuideENGLISHIf drilling a new door, use the supplied template and the complete door drilling instructions available at www.kwikset.com/doorprep.Note: Additional door preparation may be required for doors with 11/2" (38 mm) holes. Consult the deadbolt drilling instructions at www.kwikset.com/doorprep.orbacksetMeasure to conirm that the hole in the door is either 21/8" (54 mm) or 11/2" (38 mm).Measure to conirm that the backset is either 23/8" or 23/4" (60 or 70 mm).23/8" or 23/4"60 or 70 mm 13/8" – 2"35 – 51 mmMeasure to conirm that the hole in the door edge is 1" (25 mm).Measure to conirm that the door is between 13/8" and 2" (35 mm and 51 mm) thick.A B C D21/8"54 mm11/2"38 mm1"25 mm1Prepare the door and check dimensionsRequired toolsRuler4 AA BatteriesHammer Wood blockPhillips head screwdriverAdditional Tools (depending on application)AN or P (2x)NPSQABBA DIs the door edge chiseled? Which latch are you installing?YES NOUse latch “A”. If the latch bolt is not already extended, extend the latch bolt as shown.wood blockactual sizeUse latch “B” (not included). If the latch bolt is not already extended, extend the latch bolt as shown.Latch “A” Latch “B”S (2x) CQ (2x)Longer screws install closest to the door jamb.door frameEInstall strike on the door frame. Make sure the hole in the door frame is drilled a minimum of 1" (25 mm) deep.orchiseled not chiseledor2Install the latch and strikeKwikset Technical Support1-866-863-6584www.kwikset.comABABBCIs the D-shaped hole centered in the door hole?Hold the latch in front of the door hole, with the latch face lush against the door edge.YES NONo adjustment is required. Proceed to next step.D-shaped hole D-shaped holeRotate latch face as shown to extend latch.orLatch“B” is not included. If needed, please contact Kwikset to order a drive-in latch for your lock.StrikeCKeysE A BExterior AssemblyAdapter Ring DMounting PlateParts in the boxFasteners03809 46780 N Q SP66128 64109 T V49191 UInterior AssemblySmartKey ToolHMFKLG
Uactual size21/8"54 mm11/2"38 mmKStatus LED will indicate success or failure.Success: LED lashes greenFailure: LED remains solid red2 / 4 U(2x)What is the diameter of the hole in the door?Remove battery cover and battery pack from interior assembly.Install 4 AA batteries in battery pack.Install interior assembly onto mounting plate.Make sure the door is open, and insert the battery pack.After a few seconds, the latch bolt will retract and extend on its own to learn the orientation of the door. This is called the door handing process, and it is crucial to lock operation.If the latch bolt does not move on its own, or if the Status LED indicates a door handing failure, make sure the cables are connected, the batteries are installed correctly, and attempt this procedure again.If the door handing process is still unsuccessful after a second attempt, perform the “Manual Door Handing” procedure on page 4.Locate screws for step 3C and keep them within reach. Install exterior keypad and mounting plate.AAABB CDBCDiameter is 21/8" (54 mm)Diameter is 11/2"(38 mm)or“D” is required for installation. Install “D” on “F”.“D” is not needed for installation. Discard “D”. Cable goes underneath latch. Support exterior assembly during mounting plate installation.Route cable through center hole, then push cable into bottom hole. Insert key and test latch. If latch does not extend or retract smoothly, adjust screws (T). Remove key when inished and make sure the latch bolt is fully extended.Keep parallel to edge of door.Tighten screws evenly.aaccbbddMake sure turnpiece is in the vertical position.Note: Latch bolt will only retract half way.Make sure turnpiece shaft is rotated as shown. Ensure correct polarity. For best results, use new, non-rechargeable Alkaline batteries only.Do not install batteries until step 5.Ensure tight cable connection.Lay excess cable lat inside the bottom of the interior housing.alignLacbdactual sizeTbottom holeDDFFGTT (2x)TEM LLLK3Install the exterior keypad4Install the interior assembly5Install the batteries and perform the door handing processThis step will teach your lock the orientation of your door and is crucial to lock operation.
1xgreen3xredMastercodeFor enhanced security, a mastercode may be used when adding and deleting user codes. For more information about the mastercode, download the Programming and Troubleshooting Guide on the SmartCode 888 page at kwikset.com.Add the lock to your smart home systemInitiate the process to add the lock to your system at your smart home controller. Refer to your smart home system instructions for more information. When prompted by your smart home system to add the lock, press button “A” on the lock interior one time. The red LED will illuminate when the lock enters Add Mode. If successful, re-name the lock in your system (if applicable).If unsuccessful, follow your system's instructions to remove the lock from the controller and any other network, then press button “A” on the lock one time. Perform steps 6A6C again.If still unsuccessful, consult the Programming and Troubleshooting Guide on the SmartCode 888 page at kwikset.com.A B CD3 / 4Conirm that the code(s) added in previous step can unlock the door.Lock button lashes green once with one beep Lock button lashes three times with three beepsorMake sure the door is open. Press the Program button once.Install the interior cover. Secure the interior cover with three (3) screws. Note: To access the battery pack or back panel, slide up the window on the interior cover.Locking the Door Unlocking the Door Re-Key with SmartKeyEnter user code. A total of 30 user codes may be programmed.Press Lock button once.AA BB CWhat lights and sounds does the lock produce?DEach user code must be a unique code between 4 and 8 digits, depending on your smart home system.Programming was successful. Programming was unsuccessful.Make sure not to pause for more than 5 seconds during programming.Make sure the user code is not a duplicate and that it is between 4 and 8 digits during your next attempt. Make sure the lock has room for an additional code. If all user code positions are illed, delete a code to make room for this one.Press Lock button once.Enter user code.It is recommended that you add and delete all user codes through your smart home control system. If your system does not allow this, codes may be added directly to the lock as shown here.Programming Timeout During programming, if no button is pressed for ive seconds, the system will time out (indicated by three beeps and a red lashing lock button), and you will need to restart the procedure.actual sizeV button “A”Please allow time for the controller to add the lock.HRe-key the lock to work with your existing key. See the supplied SmartKey Re-key instructions for more information.V (3x)M6789Add user codes (30 max)Install the interior coverTest the lock (review normal operation) and re-key the lock (if needed)
Alert Reason SolutionLock button lashes red once with one beep*.One incorrect code entered. Re-enter code.Lock button lashes red three times with three beeps*.No user code programmed.Program at least one user code.Programming timeout after ive seconds. Attempt programming procedure again.Unsuccessful programming.Lock button lashes red 15 times with 15 beeps*Three incorrect codes entered within one minute.Re-enter code after 60 second keypad lockout.Lock button lashes red with fast beeping sound for three to four seconds.Low battery. Replace batteries.Lock button lashes green with continuous beeping sound for two seconds.Door jammed while attempting to lock.Manually re-lock door. If needed, reposition strike.Factory ResetA factory reset will delete all codes associated with the lock, and it will remove it from your smart home system.Manual Door HandingIf needed, the door handing process can be initiated manually. This is useful if the lock is being moved to a di erent door.1. Remove battery pack.Status LED2. Press and HOLD the Program button while reinserting the battery pack.Release button once battery pack is installed. The status LED will lash red and green.3. Press the Program button once more. 4. The latch bolt will extend and retract to learn the orientation of the door. The Status LED will indicate success or failure.Success: LED lashes greenFailure: LED remains solid redIf the Status LED indicates a failure, see the online Programming and Troubleshooting Guide or call Technical Support.© 2016 Spectrum Brands, Inc.1. Read all instructions in their entirety.2. Familiarize yourself with all warning and caution statements.3. Remind all family members of safety precautions.4. Protect your user codes and mastercode.5. Dispose of used batteries according to local laws and regulations. CAUTION: Prevent unauthorized entry. Since anyone with access to the back panel can change the user codes, you must restrict access to the back panel and routinely check the user codes to ensure they have not been altered without your knowledge. The use of a mastercode can help protect your system’s settings. WARNING: This Manufacturer advises that no lock can provide complete security by itself. This lock may be defeated by forcible or technical means, or evaded by entry elsewhere on the property. No lock can substitute for caution, awareness of your environment, and common sense. Builder’s hardware is available in multiple performance grades to suit the application. In order to enhance security and reduce risk, you should consult a qualiied locksmith or other security professional.Important SafeguardsIf unsuccessful: Make sure to enter the same valid code in steps 3 and 5. Test code: While the door is open, test the user code to make sure it no longer unlocks the door.If no button is pressed for ive seconds, the system will time out, and you will need to restart the procedure.Network InformationZWave System NotesThis product is a security enabled Z-wave Plus product and must be used with a Security Enabled ZWave controller to be fully utilized. ZWave is a “Wireless mesh network,” and results may vary based on building construction and communication path.To assure interoperability, each ZWave product must pass a stringent conformance test to assure that it meets the ZWave standard for complete compliance with all other devices and controls. The ZWave identity mark assures consumers, integrators, dealers and manufacturers that their products will reliably perform with any other ZWave device. And, regardless of the vendor, always powered nodes may act as a repeater for Kwikset/Weiser/Baldwin products.ZWave Coniguration and Association Parameters are available on the SmartCode 888 page at www.kwikset.com.Removing the lock from the networkFollow your smart home system’s instructions to remove the lock from the network. When prompted by the system, press button A” on the lock interior once.4 / 4SmartCode 888 at a Glance1. Press Program button once. 2. Press button “A” once. 1. Press Program button once. 2. Press button “A” once.1. Press Program button once. 2. Press button “A” once.Reference GuideStatus LEDThe Status LED blinks every 6 seconds to communicate whether the door is locked or unlocked. This feature is on by default.Blinking Green: UnlockedBlinking Amber: LockedBlinking Red: Low batterySolid Red: Unsuccessful door handing process. See online Programming and Troubleshooting Guide.Auto-LockAuto-lock automatically re-locks the door after unlocking. This feature is set to 30 seconds and is turned o by default.Turn Auto-Lock On/O Change Auto-Lock Time DelayTroubleshootingMute/Unmute AudioAudio is on by default.Deleting a single user codeNote: All codes may be deleted at once if the mastercode is enabled. For more information about the mastercode, consult the Programming and Troubleshooting Guide.Status LEDSystem AlertsExteriorKeypadLock buttonKeywaySmartKey tool holeBack panelProgram buttonStatus LEDTurnpiece shaftNote: When the cover is removed, the turnpiece shaft can be used to manually lock and unlock the door.Interior (cover removed)Button “A”A complete Programming and Troubleshooting Guide is available on the SmartCode 888 page at www.kwikset.com.3. Press button “34” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once. 3. Press button“90” once.4. Press button once that corresponds to desired time delay:“12” – 30 sec.“34” – 60 sec.“56” – 90 sec.“78” – 120 sec.“90” – 180 sec. 5. Press Lock button once.1. Press Program button once. 2. Press button “A” once.Turn Status LED On/O 3. Press button “12” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once.3. Press button “56” multiple times if needed to reach desired state.Green Lock Button: Feature is enabled.Red Lock Button: Feature is disabled.4. Press Lock button once.1. Press Program button once. 2. Press Lock button once.3. Enter user code to be deleted. 4. Press Lock button once.5. Re-enter user code. 6. Press Lock button once.1. Remove battery pack.Status LED2. Press and HOLD the Program button while reinserting the battery pack.Keep holding the button for 30 seconds until the lock beeps and the status LED lashes red.3. Press the Program button once more. When the LED lashes green and you hear one beep, the lock has been reset.4. After a few seconds, the lock will initiate the door handing process, and the latch bolt will extend and retract to learn the orientation of the door.

Navigation menu