SparkLAN Communications WPEA352ACNRB 802.11ac/b/g/n Mini PCIe Module User Manual Contents

SparkLAN Communications, Inc. 802.11ac/b/g/n Mini PCIe Module Contents

UserManual.wiki >

SparkLAN Communications >

WPEA352ACNRB User Manual

User Manual

1 WPEA-352ACNRB WPEA-352ACNRBI Manual

2 1.PRODUCT INTRODUCTION Standard IEEE802.11ac/a/b/g/n Chipset solution QCA9880-BR4A Radio stream [Note1] 3T3R Antenna type / connector. External with IPEX connector Bus Interface PCI Express Form Factor Mini-PCIe Data Rate 802.11b: 11, 5.5, 2, 1 Mbps; 802.11g: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11a: 54, 48, 36, 24, 18, 12, 9, 6 Mbps 802.11n: MCS 0 to 15 for HT20MHz MCS 0 to 15 for HT40MHz 802.11ac: MCS 0 to 8 for HT20MHz MCS 0 to 9 for HT40MHz MCS 0 to 9 for HT80MHz 1. In HT (High Throughput) mode, the data rate depends on the MCS Index. 2. The MCS index for HT (High Throughput) mode is from 0 to 32 as described in the MCS table. Spreading /Modulation Techniques 802.11a: OFDM (BPSK, QPSK, 16-QAM, 64-QAM) 802.11b: DSSS (DBPSK, DQPSK, CCK) 802.11g: OFDM (BPSK,QPSK,16-QAM,64-QAM) 802.11n: OFDM (BPSK,QPSK,16-QAM,64-QAM) 802.11ac: OFDM (BPSK,QPSK,16-QAM,64-QAM, 256-QAM) Frequency Range [Note2] 11b/g/n: 2.412GHz ~ 2.484GHz 11ac/a/n: 5.15GHz ~ 5.85GHz

3 Transmit Output Power (Tolerance: +/-2dBm) 802.11a: 14dBm@54Mbps 802.11b: 20dBm@11Mbps 802.11g: 16dBm@54Mbps 802.11gn HT20: 15dBm@MCS7 802.11gn HT40: 15dBm@MCS7 802.11an HT20: 13dBm@MCS7 802.11an HT40: 13dBm@MCS7 802.11ac VHT80: 10dBm@MCS9 Receiver Sensitivity 802.11a: ≤-73dBm@54Mbps 802.11b: ≤-86dBm@11Mbps 802.11g: ≤-73dBm@54Mbps 802.11gn HT20: ≤-70dBm@MCS7 802.11gn HT40: ≤-67dBm@MCS7 802.11an HT20: ≤-71dBm@MCS7 802.11an HT40: ≤-68dBm@MCS7 802.11ac VHT80: ≤-58dBm@MCS9 Operating Voltage DC 3.3V Power Consumption TX:1360mA (Max) Temperature Range -20°C~ +65°C (Operating) /-30°C~ +75°C (Storing) Humidity (non-condensing) 10~85 % (Operating), 5~90 % (Storing) [Note3] Security WEP / WPA / WPA2,802.1X OS supported Linux (Linux supports have different versions based on different CPU platforms and O/S. Please contact SPK support group.) Note: 1. For Radio stream with diversity or MIMO design, all RF connectors on the module must be fitting antennas in order to guarantee the module performance. 2. The frequency range is subject to local regulations. 3. The storing condition is only for product functionality, no included for parts appearance.

4 2. HARDWARE SPECIFICATION 2.1 Hardware Dimension Dimension: 50.8mm * 29.85mm * 4.1mm(±0.5mm)

5 The following section illustrate signal pin-outs for the system connector. 2.3 Pin Assignment Pin# Pin Name Description Pin# Pin Name Description 1 WAKE_L(NA) Output and open Drain active Low signal. This signal is used to request that the system return from a sleep/suspended state to service a function initiated wake event. 2 +3.3V +3.3V 3 No Connection - 4 GND GND 5 No Connection - 6 No Connection - 7 CLKREQ_L Output for reference clock request signal 8 No Connection - 9 GND GND 10 No Connection - 11 REFCLK- Input signal for PCI Express differential reference clock (100 MHz) 12 No Connection - 13 REFCLK+ Input signal for PCI Express differential reference clock (100 MHz) 14 No Connection - 15 GND GND 16 No Connection - 17 No Connection - 18 GND GND 19 No Connection - 20 W_DISABLE_L Input and active low signal. This signal is used by the system to disable radio operation on add-in cards that implement radio frequency applications. When implemented, this signal requires a pull-up resistor on the card 21 GND GND 22 PERST_L Input signal for

6 * NA: No active functional reset to the card 23 PERn0 PCI Express x1 data interface: one differential receive pair 24 +3.3V +3.3V 25 PERp0 PCI Express x1 data interface: one differential receive pair 26 GND GND 27 GND GND 28 No Connection - 29 GND GND 30 No Connection - 31 PETn0 PCI Express x1 data interface: one differential transmit pair 32 No Connection - 33 PETp0 PCI Express x1 data interface: one differential transmit pair 34 GND GND 35 GND GND 36 No Connection - 37 GND GND 38 No Connection - 39 No Connection - 40 GND GND 41 No Connection - 42 No Connection - 43 GND GND 44 LED_WLAN_L (OPT) Output and open drain active low signal. This signal is used to allow the PCI Express Mini Card add-in card to provide status indicators via LED devices that will be provided by the system 45 No Connection - 46 No Connection - 47 No Connection - 48 No Connection - 49 No Connection - 50 No Connection - 51 No Connection - 52 +3.3V +3.3V

7 * OPT: Optional (Depends on S/W and H/W design of the module and customer platform main board, functionalities of end devices and drivers.)

8 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. This device is restricted to indoor use. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The module is limited to OEM installation ONLY. This module is intended for OEM integrators under the following conditions: 1. This module is restricted to installation in products for use only in mobile and fixed applications. 2. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. 3. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. 4. OEM integrator has be limited the operation channels in channel 1-11 for 2.4GHz band. 5. Fixed outdoor applications for point to multipoint operations are subject to the conditions in Part 15.407(a)(1)(i).

9 The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations The user manual of the end product should include 1. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 2. the restriction of operating this device in indoor could void the user’s authority to operate the equipment. 3. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. 4. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 5. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label of the end product: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: RYK-WPEA352ACNRB". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. If the labelling area is considered too small and therefore it is impractical (smaller than the palm of the hand) to display the compliance statement, then the statement may be placed in the user manual or product packaging. ISED Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage;

11 This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps Modular OEM Integrator Notice This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit être installée de telle sorte qu'une distance de 20cm est respectée entre l'antenne et les utilisateurs, et 2) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the ISED compliance requirement of the end product, which integrates this module. 3. Appropriate measurements and if applicable additional equipment authorizations of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations and different antenna configurations End Product Labeling The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: 6158A-WPEA352ACNB”. Contient le module d'émission IC: 6158A-WPEA352ACNB The Host Model Number (HMN) must be indicated at any location on the exterior of the end product or product packaging or product literature which shall be available with the end product or online.

Navigation menu