SparkLAN Communications WMIR278GN 11GN mini-PCI User Manual WMIR 278GN FCC IC

SparkLAN Communications, Inc. 11GN mini-PCI WMIR 278GN FCC IC

UserMan_RYK-WMIR278GN

User’s Guide 1 Wireless Network Card Series User’s Guide
User’s Guide 2 Product Name 11Mbps/54Mbps/300Mbps 802.11b/g/n draft WLAN MIMO mini PCI card Model Number WMIR-278GN Host Interface Mini PCI type 3B Chipset solution Ralink, RT3062 ( MAC/BBP/RF) RF chain 2T2R for HT20, HT40 Guard interval ( GI ) Long/Short GI for both HT20 and HT40 Dimension 59.75mm*44.6mm*3.55mm Weight 7g Frequency Band 802.11b ISM band 2.400 ~ 2.484GHz (subject to local regulations) 802.11g ISM band 2.400 ~ 2.484GHz (subject to local regulations) 802.11n draft ISM band 2422 – 2452MHz (channel BW=40MHz) 2400 – 2483.5MHz (channel BW=20MHz) Number of Channel 802.11b USA and Canada – 11 Most European countries – 13 Japan – 14 France – 4 802.11g USA and Canada – 11 Most European countries – 13 Japan – 14 HT20 USA and Canada – 11 Most European countries – 13 WMIR-278GN 802.11b/g/n Mini-PCI Module  SPECIFICATION
User’s Guide 3Japan – 13 HT40 USA and Canada – 3~9 Most European countries – 3~9 Operating Voltage 3.3V ± 5% Spreading 802.11b Direct Sequence Spread Spectrum (DSSS) 802.11g Orthogonal Frequency Division Multiplexing (OFDM) HT20 Orthogonal Frequency Division Multiplexing (OFDM) Multiple-input/multiple-output (MIMO) HT40 Orthogonal Frequency Division Multiplexing (OFDM) Multiple-input/multiple-output (MIMO) Modulation 802.11g 64 QAM, 16 QAM, QPSK, BPSK 802.11b CCK, DQPSK, DBPSK HT20, HT40 64 QAM, 16 QAM, QPSK, BPSK Data Rate 802.11b 11, 5.5, 2, 1 Mbps per channel, auto fallback for extended range 802.11g 54, 48, 36, 24, 18, 12, 9, 6 Mbps per channel, auto fallback for extended range HT20 Refer to HT20 output power table HT40 Refer to HT40 output power table Antenna Two antenna connectors, Two antenna port for TX/RX. Transmitted power 802.11b 1Tx ~ 15 +/-1.5dBm@ch1~ch14 802.11g 1Tx ~ 14 +/-1.5dBm@ch1~ch14 HT20 please see the output power table for detail. tolerance: +/-1.5dBm HT40
User’s Guide 4please see the output power table for detail. tolerance: +/-1.5dBm Receive Sensitivity Nominal Temp Range: 802.11b (1Rx) Typ. 1Mbps, -93dBm Typ. 2Mbps, -93dBm Typ. 5.5Mbps, -92dBm Typ. 11Mbps, -90dBm 802.11g (2Rx) Typ. 6Mbps, -93dBm Typ. 9Mbps, -93dBm Typ. 12Mbps, -92dBm Typ. 18Mbps, -90dBm Typ. 24Mbps, -87dBm Typ. 36Mbps, -84dBm Typ. 48Mbps, -80dBm Typ. 54Mbps, -78dBm HT20 (2Rx) Typ. MCS=0, -93dBm Typ. MCS=1, -91dBm Typ. MCS=2, -88dBm Typ. MCS=3, -86dBm Typ. MCS=4. -83dBm Typ. MCS=5, -79dBm Typ. MCS=6, -77dBm Typ. MCS=7, -75dBm Typ. MCS=8, -91dBm Typ. MCS=9, -88dBm Typ. MCS=10, -86dBm Typ. MCS=11, -83dBm Typ. MCS=12, -80dBm Typ. MCS=13, -75dBm Typ. MCS=14, -74dBm Typ. MCS=15, -72dBm HT40 (2Rx) Typ. MCS=0, -90dBm Typ. MCS=1, -88dBm Typ. MCS=2, -85dBm Typ. MCS=3, -83dBm Typ. MCS=4, -80dBm
User’s Guide 5Typ. MCS=5, -76dBm Typ. MCS=6, -74dBm Typ. MCS=7, -72dBm Typ. MCS=8, -88dBm Typ. MCS=9, -85dBm Typ. MCS=10, -83dBm Typ. MCS=11, -80dBm Typ. MCS=12, -77dBm Typ. MCS=13, -72dBm Typ. MCS=14, -71dBm Typ. MCS=15, -69dBm Power consumption (Average) 802.11b Continue TX : 470mA@3.3V Continue RX : 250mA@3.3V 802.11g Continue TX : 420mA@3.3V Continue RX : 250mA@3.3V HT20 Continue TX : 530mA@3.3V Continue RX : 260mA@3.3V HT40 Continue TX : 550mA@3.3V Continue RX : 290mA@3.3V LED indicator N/A Supplied Driver Windows 2000/XP 32/Vista 32/Win7 32, please refer to software spec in detail. Standards IEEE 802.11b, IEEE 802.11g i3standard, Wi-Fi compliant ,EWC 802.11n draft Temperature Range 0 ~ 55°C (Operating); -20 ~ 80°C (Storing) Humidity Operating Humidity 10% to 85% Non-Condensing Storage Humidity 5% to 90% Non-Condensing Network Protocol TCP/IP, IPX, NDIS4, and NDIS5x Management Utility Monitor Internet Access Status via UI System Requirements Laptop containing  miniPCI slot  64MB memory or greater  300MHz processor or greater Microsoft Windows 2000/XP 32/Vista 32/Win7 32
User’s Guide 6 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.
User’s Guide 7This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains FCC ID: RYK-WMIR278GN”. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
User’s Guide 8Canadian Regulatory Wireless Notice This device complies with RSS-210 of the Industry Canada Rules. Operation is subject to the following two conditions: 1) this device may not cause interference and 2) this device must accept any interference, including interference that may cause undesired operation of the device IMPORTANT NOTE: Canada Radiation Exposure Statement: This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Navigation menu