Sony Group S445C Sony Remote Card System Reader/Writer RC-S445C User Manual

Sony Corporation Sony Remote Card System Reader/Writer RC-S445C

User Manual

Sony ConfidentialFeliCa Reader/Writer RC-S441C and RC-S445C- Users Manual - (Version 2.10) Sony Corporation19 November 1999 “FeliCa” is a trademark of Sony CorporationContents1 Definition 12 General 12.1 Basic Specification 12.1.1 Dimensions 1
FeliCa: Reader/Writer RC-S441,445 Users Manual Sony Confidential ii2.1.2 Specification Table 12.1.3 Encryption Technique 23 Reader/Writer Operation 33.1 Connection with Controller 33.2 Transaction Overview 33.2.1 Communication Protocol 33.2.2 Re-sending Protocol 33.2.3 ACK/NACK Packet 33.2.4 Mutual Authentication 33.2.5 Encryption and Decryption 44 Communication Commands 44.1 General 44.2 Reader/Writer Internal Operation Commands 44.2.1 Attention Command 44.2.2 Authentication 1 Command 44.2.3 Authentication 2 Command 44.2.4 Disconnect Command 44.2.5 Change Reader/Writer Access Key Command 44.2.6 Self-Diagnosis Command 64.2.7 Check Firmware Version Command 64.2.8 Change Communication Mode Command 64.2.9 Kill Module Command 64.2.10 Reader/Writer Reset Command 64.2.11 Firmware Maintenance Command 64.3 Card Operation Command 64.3.1 Polling Command 64.3.2 Request Service Command 64.3.3 Request Response Command 64.3.4 Mutual Authentication Command 64.3.5 Read Block Command 64.3.6 Write Block Command 74.3.7 Release Command 74.3.8 Read Without Encryption Command 74.3.9 Write Without Encryption Command 74.4 Card Management Command 84.4.1 Register Issue ID Command 84.4.2 Register Area Command 84.4.3 Register Service Command 84.4.4 Register Manufacture ID Command 84.4.5 Card Self-Diagnosis Common Security Key Command 85 Fundamental Specifications 95.1 Operating Temperature 95.2 Storage Temperature 95.3 Humidity 95.4 Cold and Heat Shock 95.5 Shock 95.6 Vibration 95.7 Spurious Emissions 95.8 Bump 95.9 Electrostatic Discharge 95.10 Multiple cards 95.11 Anti-Collision 9
FeliCa: Reader/Writer RC-S441,445 Users Manual Sony Confidential iii6Reader/Write Specification Table 106.1 Type C Reader/Writer 106.1.1 Type C Reader/Writer Specification Table 10•Model No. 10•Operating Distance 10•Interface Connector 11•External Interface 12•Dimensions 13•Mounting Holes 13•Power 136.1.2 Type C Reader/Writer Schematic Drawing 136.2 Type E Reader/Writer 156.2.1 Type E Reader/Writer Specification Table 15•Model No. 15•Operating Distance 15•Interface Connector 15•External Interface 15•Dimensions 16•Mounting Holes 16•Power 166.2.2 Type E Reader/Writer Schematic Drawing 17
FeliCa: Reader/Writer RC-S441,445 Users Manual Sony Confidential ivList of TableTable 1 Reader/Writer RC-S44x Models 1Table 2 Reader/Writer Internal Operation Command 4Table 3 Card Operation Command 4Table 4 Card Management Command 4Table 5 Pin Assignment of Interface Connector CN2 12List of FiguresFig.1 Communication Protocol and Packet Structure 3Fig.2 Printed Model No. (type C) 10Fig.3 Example of Antenna Placement (type C) 11Fig.4 Pin Assignment of Connectors CN1-3 11Fig.5 Placement of Parts for RS-232C Interface 12Fig.6 Antenna Board (type C) 13Fig.7 RF/Control Board 14Fig.8 Printed Model No. (type E) 15Fig.9 Antenna Board (type E) 17
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 11 DefinitionIn this document, following words are used in the following sense.Controller - An external computer, a gate controller or an equivalent equipment directlyconnected to Reader/Writer through specified wired interface.Reader/Writer - The equipment, specified in this document, for Sony Remote CardSystem : FeliCa.Card - A Contactless Smart Card for Sony Remote Card System : FeliCa2 General2.1 Basic SpecificationTable 1 shows Reader/Writer “RC-S44x” models. RC-S445 has dual CPUs andexternal memories for sub CPU. RC-S441 is a single CPU type same as the modelsRC-S430 and RC-S480.Reader/Writer consists of 3 parts – an antenna board, an RF/control board and thecable that connects the antenna board and the RF/control board. There are 2 antennatypes called Type C and E (see Chapter 6).Model No. CPU Memory AntennaTypeSerialInterface ConnectorTypeRC-S445C/6L Dual Flash 4MbyteSRAM 0.5Mbyte CRS485ARS232C Right angleRC-S441C/6L C StraightRC-S441E/6L Single - ERS485ACMOS Right angleTable 1 Reader/Writer RC-S44x models2.1.1 DimensionsThe dimension of each type are described in Chapter 6.The tolerance is ±0.5mm.2.1.2 Specification TableCommunication with Card( Common )carrier frequency: 13.56MHz (±50ppm)modulation bandwidth: ±300kHz (-30dB relative to carrier level)radiation level: less than 4500µV/m at 10m (Type C Antenna) 1000µV/m at 10m (Type E Antenna) 300µV/m at 10m (Type B Antenna)Communication method: half-duplex, CRC16( ISO type C )data transfer rate : 211.875kbpsmodulation: Receive - ASK, Manchester Coding Transmit - ASK(8-14%), Manchester Codingmodulation bandwidth: ±300kHz (-30dB relative to carrier level)( ISO type B )[Note] ISO/IEC document 14443 on the type B protocol was notpublished at the design stage of these Reader/Writer. The design wasmade according to then the newest available documents as describedbelow.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 2 ISO/IEC JTC1/SC17 CD 14443-2 document N1433 (22.10.1998) ISO/IEC JTC1/SC17 2nd CD 14443-3 document N1475R (28.2.1999)data transfer rate : 106 kbpsmodulation: Receive - ASK, BPSK( sub carrier 847.5kHz) Transmit - ASK(8-14%), NRZmodulation bandwidth: ±100kHz (-30dB relative to carrier level, 106 kbps)Power Supply (see Chapter 6)Digital Processing Unit (DPU)Main: CXD8680R (designed by Sony)Clock Frequency = 13.56MHzCXD8680R has a 32 bit CPU core, 8 kbyte ROM, 3 kbyte SRAM, 2 kbyte BlockErasable Flash Memory and 4×32 kbyte Flash Memory inside.Sub: 32 bit CPU MC68340 (RC-S445)Clock Frequency = 13.56MHzExternal MemoryRC-S445: 4 Mbyte Flash Memory and 500 kbyte SRAMController Interface (serial interface)number of ports : 1 (one)signal level : RS485 and CMOS logic level (5V) for RC-S441C/E: RS485 and RS232C for RC-S445Cbaud rate for operation: 7.2kbps ∼ 1.2288Mbps(7.2, 8.192, 9.6, 14.4, 16.384, 19.2, 28.8, 32.768, 38.4,57.6, 65.536, 76.8, 115.2, 131.072, 153.6, 230.4, 262.144,460.8, 524.288, 921.6, 1048.576, 1228.8 kbps): 50bps ∼ 115.2kbps (Sub CPU)communication method : half-duplex, check sum2.1.3 Encryption TechniqueAll communications to and from the Card, with the exception of Polling Command,are encrypted.All the communications to and from the Controller, with the exception of theAttention Command, are encrypted.Two kinds of Encryption algorithm, Single-DES 56bit and Triple-DES 56bit can beapplied.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 33Reader/Writer Operation3.1 Connection with ControllerThe pin assignment is described in Chapter 6.3.2 Transaction Overview3.2.1 Communication ProtocolThere are two communication protocols, namely, data link level and application levelprotocol.Either ACK or NACK packet is returned in every packet transfer. ACK indicates asuccessful transfer, NACK means unsuccessful.Fig. 1 : Communication Protocol and Packet Structure3.2.2 Re-sending ProtocolReader/Writer supports the re-sending procedure in Controller interface. Re-sendinghandling is triggered or required in the two cases below :1. NACK packet is returned.2. Neither ACK nor NACK response comes. (time out)Controller should re-send the same packet within 5ms after receiving NACK ordetecting time out.3.2.3 ACK / NACK PacketACK / NACK packet format is as follows :ACK : LEN = 00h & LCS = ffh without Packet Data part and DCSNACK : LEN = ffh & LCS = 00h without Packet Data part and DCS3.2.4 Mutual AuthenticationMutual Authentication is a process that is performed between Controller andReader/Writer to authenticate each other mutually in order to avoid the fraud usage.Reader/WriterControllerMax. 2msCommand PacketACKACKMax. 2msResponse Packet 00 FF00 LEN LCS PD0PDnPD1DCS 00…PostamblePacket Data ChecksumPacket DataPacket Length ChecksumStart of Packet CodePacket LengthPreambleCommand or Response Code
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 4This authentication is based on the following elements :1. two 8byte (64bit) keys2. three pass authentication model (ISO 9758)3. cryptography algorithm mentioned in section 3.2.5. 3.2.5 Encryption and Decryption The cryptography algorithm is used for the following three stages :1. mutual authentication between Controller and Reader/Writer2. mutual authentication between Reader/Writer and Card3. commands and data encryption through Reader/Writer4 Communication Commands 4.1 General In this section, the communication commands between Controller and Reader /Writerare described. Table 2-4 shows all commands between Controller and general Reader/Writer. Allcommands are categorized into 3 groups as follows :1. Reader/Writer internal operation command2. Card operation command3. Card management command Card management command group is for issue Reader/Writer and not for generalReader/Writer . 4.2 Reader/Writer Internal Operation Command 4.2.1 Attention Command Attention Command enables Reader/Writer and Controller to recognize each otherand is the only command available before the authentication completes. The mainpurpose of this Attention Command is to recognize its partner before authenticationand to force Reader/Writer to be in the idle state. 4.2.2 Authentication 1 Command Authentication 1 Command enables Controller to authenticate Reader/Writer. 4.2.3 Authentication 2 Command Authentication 2 Command enables Reader/Writer to authenticate Controller. 4.2.4 Disconnect Command Disconnect Command is for Controller to terminate the communication withReader/Writer. 4.2.5 Change Reader/Writer Access Key CommandChange Reader/Writer Access Key Command performs alteration of the accesskeys, which are stored in Reader/Writer for the mutual authentication betweenController and Reader/Writer.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 5Command Command Code Response CodeAttention 00h 01hAuthentication 1 02h 03hAuthentication 2 04h 05hDisconnect 06h 07hChange Reader/Writer Access Key 20h 21hSelf-Diagnosis 40h 41hCheck Firmware Version 44h 45hChange Communication Mode 46h 47hKill Module 4ah 4bhReader/Writer Reset 4ch 4dhFirmware Maintenance 52h 53hTable 2 : Reader/Writer Internal Operation CommandCommand Command Code Response CodePolling 80h 81hRequest Service 82h 83hRequest Response 84h 85hMutual Authentication 86h 87hRead Block 88h 89hWrite Block 8ah 8bhRelease 8eh 8fhRead Without Encryption 98h 99hWrite Without Encryption 9ah 9bhTable 3 : Card Operation CommandCommand Command Code Response CodeRegister Issue ID c0h c1hRegister Area c2h c3hRegister Service c4h c5hRegister Manufacture ID e0h e1hCard Self-Diagnosis f0h f1hTable 4 : Card Management Command
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 6 4.2.6 Self-Diagnosis Command Self-Diagnosis Command activates self-diagnosis test of Reader/Writer. After theDiagnosis completion, Reader/Writer sends back the test result. 4.2.7 Check Firmware Version Command Check Firmware Version Command is used for checking the version ofReader/Writer firmware. 4.2.8 Change Communication Mode Command Change Communication Mode Command performs the following changes : baudrate, logic level interface(non-inverted or inverted), encryption on/off, time-out. 4.2.9 Kill Module Command Kill Module Command is used for killing the specified module within Reader/Writer. 4.2.10 Reader/Writer Reset Command Reader/Writer Reset Command executes the initialization routine. 4.2.11 Firmware Maintenance Command Firmware Maintenance Command is used for updating the firmware withinReader/Writer. 4.3 Card Operation Command 4.3.1 Polling Command Polling Command enables Reader/Writer to give a call to Card and to detectexistence of Card by the response from Card. 4.3.2 Request Service Command Request Service Command enables Reader/Writer to check whether the specifiedservice code is registered to Card or not. In case that the specified service isregistered to Card, key version of the service is available by the response from Card. 4.3.3 Request Response Command Request Response Command enables Reader/Writer to check which mode Card isin. There are 4 modes, ‘before Authentication’, ‘after Authentication 1’, ‘afterAuthentication 2’ and ‘after Register xxx Command (see 4.4 Card ManagementCommand)’. 4.3.4 Mutual Authentication Command Mutual Authentication Command activates the mutual authentication procedurebetween Reader/Writer and Card. 4.3.5 Read Block Command Read Block Command activates Reader/Writer to read the specified block data fromCard after the mutual authentication between the Reader/Writer and Card has beenestablished successfully. Read Block Command enables a Service Provider with successful mutualauthentication to read blocks that this Service Provider has the right to access. With one Read Block Command, up to 8 block can be read simultaneously. If morethan 8 blocks should be read, more than one Read Block Command shall be calledseparately. The response of Read Block Command is a 1byte Read result and Block Data thathas been read. In the Read result, a 1byte consequence of one block Read is givenin 1bit. As there are up to 8 blocks, 1byte is enough to record all the Readconsequence.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 7 4.3.6 Write Block Command Write Block Command activates Reader/Writer to write the specified block data toCard as new data after the mutual authentication between Reader/writer and Cardhas been established successfully. With one Write Block Command, up to 8 block can be written simultaneously. Ifmore than 8 blocks should be written, more than one Write Block Command shall becalled separately. The response of Write Block Command is a 1byte Write result. In the Write result, a1byte consequence of one block Write is given in 1bit. As there are up to 8 blocks,1byte is enough to record all the Write consequence. The purse operation can be performed with Write Block Command. 4.3.7 Release Command Release Command enables Card to be released from established communicationsequence with Reader/Writer. 4.3.8 Read Without Encryption Command Read Without Encryption Command activates Reader/Writer to read the specifiedblock data from Card without the mutual authentication between the Reader/Writerand Card. Read Without Encryption Command can be applied only to blocks whichservice code is registered security-free. The number of blocks that can be read simultaneously and the response of ReadWithout Encryption Command are the same as those for Read Block Command (see4.3.5). 4.3.9 Write Without Encryption Command Write Without Encryption Command activates Reader/Writer to write the specifiedblock data to Card without the mutual authentication between the Reader/Writer andCard, however can be applied only to blocks which service code is registeredsecurity-free. The number of blocks that can be write simultaneously and the response of WriteWithout Encryption Command are the same as those for Write Block Command (see4.3.6).
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 84.4 Card Management Command The commands described in this section are for issue Reader/Writer and not forgeneral Reader/Writer . 4.4.1 Register Issue ID Command Register Issue ID Command makes it possible to register Issue ID(IDi) , IssueParameter(PMi), System Code and Area 0000 Key to Card, and also makes it toerase other services and to initialize Memory Allocation Information in Card. 4.4.2 Register Area Command Register Area Command makes it possible to register new Area and the parametersof new Area to Card, which are Service Code Range, Available Block Number andArea Key. 4.4.3 Register Service Command Register Service Command makes it possible to register new Service and theparameters of new Service to Card, which are Service Code, Block Number andService Key. 4.4.4 Register Manufacture ID Command Register Manufacture ID Command makes it possible to register ManufactureID(IDm) , Manufacture Parameter(PMm), System Code, System Key and Area 0000Key to Card, and also makes it to clear Issue ID of Card. In order to execute Register Manufacture ID Command, Manufacture ID must be all00h. This means that Register Manufacture ID Command is effective to Card once forall. 4.4.5 Card Self-Diagnosis CommandCard Self-Diagnosis Command activates self-diagnosis test of Card. After theDiagnosis completion, Card sends back the test result.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 95 Fundamental Specifications 5.1 Operating Temperature -20 to 85°C Compliant to IEC 68-2-2 Part 2 Test Bd and IEC 68-2-1 Part 2 Test Ad, with duration16 hours. 5.2 Storage Temperature -40 to 85°C Compliant to IEC 68-2-2 Part 2 Test Bb and IEC 68-2-1 Part 2 Test Ab, with duration72 hours. 5.3 Humidity Compliant to IEC 68-2-3 Part 2 Test Ca, with duration 4 days. 5.4 Cold and Heat Shock Compliant to IEC 68-2-1 Part 2 Test Aa, with temperature -20°C and duration 2 hours,and IEC 68-2-2 Part 2 Test Ba, with temperature 70°C and duration 2 hours. 5.5 Shock Compliant to IEC 68-2-27 Part 2 Test Ea, severity 60g, duration 11ms. 5.6 Vibration Compliant to IEC 68-2-6 with respect to the following parameters :•Frequency Range : 10Hz to 500Hz•Vibration Severity : 3gn•Sweep rate : 1 octave per minute•Endurance by sweeping : 20 sweep cycles for each X,Y and Z axis. 5.7 Spurious Emissions Compliant to MPT 1339 clause 4.1.3 ; FCC Regulation Part 15.225 and Part 15.209 ;and EC(EU) I-ETS 300 330 clause 7.2.1.3. 5.8 Bump Compliant to IEC 68-2-29 Part 2 Test Eb, severity 40gn, duration 6ms and 4000bumps. 5.9 Electrostatic Discharge Compliant to IEC 801-2, with severity level 3 (Test Voltage Air discharge : 8kV ). 5.10 Multiple Card The Reader/Writer allows addressing and authentication of up to four Cards in thecommunication area. Each Card will only respond to commands intended for it and onlyone Card can be addressed in a single command. 5.11 Anti-Collision Reader/Writer supports anti-collision of multiple cards.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 10 6Reader/Writer Specification Table 6.1 Type C Reader/Writer 6.1.1 Type C Reader/Writer Specification Table•Model No. RC-S441C/6L and 445C/6LGeneral model No. “RC-S441” or “RC-S445” is printed on the RF/Control board(see Fig.2-1and 2-2). “Type C” means antenna type shown in Fig.6 and it ismarked on “C” as in Fig.2. A mark on numerals 1-6 (it is 1 in Fig.2-1 and 2-2)indicates the installed software version. Fig.2-1 Fig.2-2Fig.2 : Printed Model No. (Type C )•Operating Distance : 100mm (Card : RC-S832)- The Reader/Writer is adjusted by the combination of the RF/Control boardand the antenna board, both of which shall have the same serial number labelsto maximize the operating distance, and therefore, the operating distancecannot be assured by the different combination of the boards.- The antenna board and the RF/Control board shall be placed more than30mm apart to prevent decrease of the operating distance more than 10mm,i.e. to obtain more than 90mm operating distance. In case of adjusting thevariable capacitor on the RF/Control board to maximize the output level, theminimum distance between the boards is improved to 15mm . (see Fig. 3)- In the effective operating scope of the antenna, there shall be nothing thatgenerates electric or magnetic noise. Neither shall there be an electric ormagnetic shield or reflection.- Emission from another Reader/Writer affects the operating distance. Inoperating plural Reader/Writers simultaneously, it is desirable for antennaboards to be separated more than 70cm each other in order to keep the100mm operating distance. However, Reader/Writers can be operated underless than 70cm separation each other with no problem except for decrease ofthe operating distance.RC-S445ABDCEF123456RC-S441ABDCEF123456
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 11Fig.3 : Example of Antenna Placement (Type C)•Interface ConnectorRC-S441C/6L: Methode 1100-12-110-01 (straight)RC-S445C/6L: Methode 1100-12-110-02 (right angle) The interface connector is a 10-pin connector located at the right edge of theRF/Control board which is shown in the schematic drawing of Fig.7. The pitch ofconnector pins is 2.54mm. The most upper connector pin is No. 1. Pinassignment of the connector is shown in Fig. 4 and Table 5. Fig.4 : Pin Assignment of Connectors CN1-3 Pin No. 12345678910Pin Assignment SHDN GND DCIN RX- RX+ TX- TX+ TXD GND RXD Table 5 : Pin Assignment of Interface Connector CN3 AntennaControl boardd > 15mmExternal I/OTX+TX-RX+RX-5VGNDOUTIN TXDRXDSISOModu., Demodu. & Power Amp.*R/WRD*WDGND5VCARRIER*CARRIER12VRFIN+RFIN-RFOUT+RFOUT-EN/*INHController1SISOMODE5V*TORI*R/WCARRIER*CARRIEREN/*INHGNDDA[0-7]DB[0-7]HS[0-3]PA[0-7]GPSELCLKSIESCLKECC/*DCDSCR/*W*RESETCACKGR/*WData Conv. & Sel.GDAT[0-3]GPSEL5VGNDTO_IRI_OSCLKE_OSIE_OGACKGRQGC/*DGTOGRIGDSCLK*RESETGR/*WO1I1O2I2MI1MI2MO1MO2SOSIController2SISOMODE5VCLKGNDPA[0-7]PB[5-7]*RESETCACKDC-DC12V5VGNDINH5V5V5V12V5V5V5V12V12VDB[0-7]HS[0-3]DB[0-7]DA[0-7]HS[0-3]DA[0-7]SHDNTX+(RS485)TX-(RS485)GNDRXD(RS232C/CMOS)RX-(RS485)12VRX+(RS485)TXD(RS232C/CMOS)GNDto Ant.PB6PB5PB[5-7]PB7PA[0-7]TXDDB7DB2DB6DA7RX-DA0DB7DB1DA6MODE1DB5DA3DB3DA1 MODE2SOSIDB[0-3]DA2RX+GNDHS2DA5HS0GNDHS1DA4RXDTX+TX-DB6DB0DB4DB4GNDHS3GPSELGNDSHDNDB512V12VCN312345678910CN11234CN2CON40A13579111315171921232527293133353739246810121416182022242628303234363840FUSE
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 12•External Interfaceserial 1 port: RS-485A and CMOS logic level (5V) for RC-S441C RS485A and RS232C for RC-S445Csoftware selectable, non-inverted or inverted, and baud rate(default setting : non-inverted, 115.2kbps) Common pins are assigned for RS-232C and CMOS logic level. CMOS logiclevel can be available instead of RS232C for RC-S445C by mounting 2 resistorsR46-47 and removing 2 resistors R52-53 which are located near the right, lowercorner of the RF/Control board as shown in Fig.5. Fig.5 : Placement of Parts for RS-232C or CMOS Interface•Dimensions (see Fig.6 and Fig.7) antenna: 104mm × 67mm × 6mm (PCB thickness 1mm, connector height 5mm) RF/Control board: 104mm × 67mm × 10.5mm (PCB thickness 1mm) cable: length 120mm•Mounting Holes (see Fig.6 and Fig.7) antenna : M3 × 4, clearance 8mm RF/Control board : M3 × 4, clearance 7mm•Power voltage: DC12V (shall be applied to DCIN of CN2)CN3IC10 Mounting HoleR47R46R53R52RF/Control Board (0-881-428-02)110123940CN3CMOS Logic Level R46,47 : < 10 ohm R52,53 : no mountingRS-232C R46,47 : no mounting R52,53 : < 10 ohm IC10 : MAX3221CAE
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 13 voltage allowance: +4V, -0.5V current: < 400mA voltage ripple allowance: 100mV (peak-to-peak) The Reader/Writer can be operated in the voltage range of 8-11.5V and thevoltage ripple > 100mV, however operating distance cannot be assured in suchcondition. 6.1.2 Type C Reader/Writer Schematic Drawing Fig.6 : Antenna Board (Type C)
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 14 Fig.7 : RF/Control Board
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 15 6.2 Type E Reader/Writer (Limited Model) 6.2.1 Type E Reader/Writer Specification Table•Model No. : RC-S441E/6LGeneral model No. “RC-S441” is printed on the RF/Control board (see Fig.8).“Type E” means antenna type shown in Fig.9 and it is marked on “E” as in Fig.8.A mark on numerals 1-6 (it is 1 in Fig.8) indicates the installed software version.Fig.8 : Printed Model No. (Type E )•Operating Distance : 40mm (Card : RC-S832)- The Reader/Writer is adjusted by the combination of the RF/Control boardand the antenna board, both of which shall have the same serial number labelsto maximize the operating distance, and therefore, the operating distancecannot be assured by the different combination of the boards.- The antenna board and the RF/Control board shall be placed more than30mm apart.- In the effective operating scope of the antenna, there shall be nothing thatgenerates electric or magnetic noise. Neither shall there be an electric ormagnetic shield or reflection. Type E antenna is affected by conductivematerial more easily than other antenna types because a ferrite block is notattached on the antenna board.- Emission from another Reader/Writer affects the operating distance. Inoperating plural Reader/Writers simultaneously, it is desirable for antennaboards to be separated more than 50cm each other in order to keep the40mm operating distance. However, Reader/Writers can be operated underless than 50cm separation each other with no problem except for decrease ofthe operating distance.•Interface Connector : Methode 1100-12-110-02 (right angle) The interface connector is a 10-pin connector located at the right edge of theRF/Control board which is shown in the schematic drawing of Fig.7. The pitch ofconnector pins is 2.54mm. The most upper connector pin is No. 1. Pinassignment of the connector is shown in Fig. 4 and Table 5.•External Interfaceserial 1 port : RS-485A, CMOS logic level (5V)software selectable, non-inverted or inverted, and baud rate(default setting : non-inverted, 115.2kbps)•Dimensions (see Fig.7 and Fig.9) antenna: 65mm × 40mm × 6mm (PCB thickness 1mm, connector height 5mm) RF/Control board: 104mm × 67mm × 10.5mm (PCB thickness 1mm) cable: length 120mmRC-S441ABDCEF123456
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 16•Mounting Holes (see Fig.7 and Fig.9) antenna : M3 × 4, clearance 8mm RF/Control board : M3 × 4, clearance 7mm•Power voltage: DC12V (shall be applied to DCIN of CN2) voltage allowance: +4V, -0.5V current: < 400mA voltage ripple allowance: 100mV (peak-to-peak) The Reader/Writer can be operated in the voltage range of 8-11.5V and thevoltage ripple > 100mV, however operating distance cannot be assured in suchcondition.
FeliCa : Reader/Writer RC-S441,445 Users Manual Sony Confidential 17 6.2.2 Type E Reader/Writer Schematic DrawingFig.9 : Antenna Board (Type E)

Navigation menu