Sony Group DWTP01F DIGITAL WIRELESS TRANSMITTER User Manual

Sony Corporation DIGITAL WIRELESS TRANSMITTER

User manual

4-142-337-01 (1)© 2009 Sony CorporationDigital WirelessTransmitterOperating InstructionsBefore operating the unit, please read this manual thoroughly and retain it for future reference.DWT-P01F
WARNINGBatteries shall not be exposed to excessive heat such as sunshine, fire or the like.You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment.All interface cables used to connect peripherals must be shielded in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.For the customers in the U.S.A.If you have any questions about this product, you may call;Sony Customer Information Service Center 1-800-222-7669 or http://www.sony.com/This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Use of Sony wireless devices is regulated by the Federal Communications Commision as described in Part 74 subpart H of the FCC regulations and users authorized thereby are required to obtain an appropriate license.IMPORTANT NOTE: To comply with the FCC RF exposure compliance requirements, no change to the antenna or the device is permitted,Any change to the antenna or the device could result in the device exceeding the RF exposure requirements and void user’s authority to operate this device.This device complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65. This device has very low levels of RF energy that it is deemed to comply without testing of specific absorption radio (SAR).This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help. Declaration of ConformityTrade Name: SONYModel: DWT-P01(F)Responsible Party: Sony Electronics Inc.Address: 16530 Via Esprillo, San Diego, CA 92127 U.S.A.Telephone Number: 858-942-2230This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
For the customers in CanadaOperation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.Use of Sony wireless devices is regulated by the Industry Canada as described in their Radio Standard Specification RSS-123.A licence is normally required. The local district office of Industry Canada should therefore be contacted. When the operation of the device is within the broadcast band, the licence is issued on no-interference, no-protection basis with respect to broadcast signals.This model has an RF module of the FCC/IC approval built-in.BUILT IN MODULE RM-215This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This Class B digital apparatus complies with Canadian ICES-003.For the customers in EuropeIf the transmitter develops an abnormally high temperature, a burning odor or smoke during use, remove the battery holder and stop using the transmitter immediately.Take care not to burn your fingers when removing the battery holder as the batteries may be very hot at this time.For the customers in EuropeHereby, Sony Corporation, declares that this DWT-P01 is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.For details, please access the following URL: http://www.compliance.sony.de/ This product is intended to be used in the following countries : United Kingdom, Germany, Norway, Luxembourg, Belgium, Denmark, France, Italy, Sweden, Switzerland, Finland, Iceland, Turkey, and Czech Republic.Voor de klanten in EuropaHierbij verklaart Sony Corporation dat het toestel DWT-P01 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Nadere informatie kunt u vinden op:http://www.compliance.sony.de/ Dit product is bedoeld om in volgende landen gebruikt te worden: Verenigd Koninkrijk, Duitsland, Noorwegen, Luxemburg, België, Denemarken, Frankrijk, Italië, Zweden, Zwitserland, Finland, IJsland en Turkije.FCC ID: AK8RM215IC: 409B-RM215U.K. 470 - 862 MHzGermany 470 - 606 MHz, 614 - 862 MHzNorway 800 - 820 MHzLuxembourg 470 - 862 MHzBelgium 470 - 862 MHzDenmark 800.100 - 819.900 MHzFrance 470 - 830 MHzItaly 470 - 854 MHzSweden 470 - 862 MHzSwitzerland 790 - 862 MHzFinland 790.100 - 821.900 MHz, 854 - 862 MHzIceland 470 - 862 MHzTurkey 470 - 862 MHzR-16 OKR-E OK削除移動
FeaturesThe DWT-P01(F) is a digital wireless transmitter for a UHF synthesized wireless microphone system to be used for broadcast or movie production purpose. This transmitter is suitable for Electronic News Gathering (ENG).What are the strengths of a Digital Wireless Microphone System?This system has the following special features and qualities:• High-quality audio signal transmission approaching to the quality of wired microphone• Extremely tolerant to interference waves and secure wireless transmission• Simultaneous multi-channel operation• Encrypted transmission• Metadata transmission.Note that the DWT-P01(F) Digital Wireless Transmitter cannot be used to transmit to analog wireless receivers.The features of this transmitter are described below.Wide RF carrier frequency rangeThe DWT-P01(F) transmitter covers an extremely wide RF carrier frequency range. US modelscan cover a 66-MHz band and 60-MHz band respectively — much wider than 24-MHz of the analog wireless microphone system.This remarkably wide coverage on a single model offers cost efficiency and operational convenience, because it allows one transmitter to be operated in many different areas.Switchable mic or line input level and adjustable attenuatorFor details, see “Setting the audio input level (INPUT LEVEL)” .Selectable RF output power: 1 mW, 10 mW, and 50 mWFor details, see “Setting the RF output power (RF POWER)” .Power sleep modeFor details, see “Power save setting (POWER SAVE)” .Digital low-cut filterFor details, see “Low-cut filter setting (LCF)”.Easy-to-see, full dot-matrix OLED (Organic Light-Emitting Diode) DisplayThe quick response of the OLED display enables real-time operating conditions to be displayed clearly and accurately.+48 V power supply for a microphoneFor details, see “+48 V power supply setting (+48V)” .
PartsIdentificationaAudio input connector (XLR-3-11C)Connects a microphone with an XLR-3-12C-type output connector or an audio cable with an XLR-3-12C-type connector.Be sure that the transmitter is turned off before connecting a microphone or cable to the transmitter.To connect a microphone or a cablebAF (audio input level) /PEAK indicatorLights up green when the signal input is stronger than the reference level.Lights up red when the signal input is 3 dB below the level at which distortion begins. cPOWER indicatorLights up green when the transmitter is turned on. When the battery is exhausted, the indicator starts flashing.d+48V indicatorLights up when INPUT LEVEL is set to MIC and +48 V power is being supplied to a connected microphone or other device.CautionFrontBottomMicrophone or a cable (optional)Turn the connector ring clockwise (1)and insert the microphone or cable connector into the audio input connector until it is fully engaged (2). Then turn the connector ring counterclockwise to secure the latch (3).
eDisplay sectionARF transmission indicationIndicates the current transmission status.:Currently transmitting—: Transmission stoppedBRF (radio frequency) transmission power indicationIndicates the current transmission power setting. You can change the setting with the RF POWER function.H: Transmitting at 50 mWM: Transmitting at 10 mWL: Transmitting at 1 mWCAudio input level meterIndicates the input signal level of the audio input connector.DReference level gaugeIndicates the reference input level. When the attenuation is 0 dB with INPUT LEVEL set to MIC, –58 dBu (–60 dBV) is indicated. When LINE is selected for INPUT LEVEL, +4 dBu is indicated.EPeak indicatorWarns of excessive input by lighting up when the signal is 3 dB below the level at which distortion begins.FPOWER switch lock indicatorIndicates that the POWER switch is locked, preventing the transmitter from being accidentally turned off or on.For details, see “Locking the POWER switch (POWER SW LOCK)”.GWireless remote control condition indicationIndicates the signal transmission condition of the wireless remote control function (4 levels).: Good transmission: Somewhat good transmission: Somewhat poor transmission: Poor transmission: Unable to communicate with paired receiverWhen the wireless remote control function is off, this indication does not appear.HBattery indicationShows the battery condition.For details, see “Battery indication”.IMenu display sectionThe status of 17 different functions are displayed here. To select the function, press the + or – button repeatedly.For details, See “Setting Menus”.f + or – buttonSelects functions or values shown on the display.Holding down the – button while switching on the transmitter activates the pairing operation for the wireless remote control function.gSET buttonAdjusts displayed function settings and enters the value.Holding down the SET button while switching on the power turns the transmitter on without sending a signal.hUSB connector (Micro USB)Use this connector to connect an optional USB keyboard to carry out menu functions using key operations. By connecting the digital wireless receiver to this connector with the supplied USB cable, you can
exchange the encryption key for encrypted transmission function.iPOWER switchTurns the transmitter ON or OFF.jBattery compartmentAccommodates two LR6 (size AA) alkaline batteries.For details on how to insert the batteries, see “Power Supply”.Power SupplyThe transmitter can operate on two LR6 (size AA) alkaline batteries continuously for about 3.5 hours at 25°C (77°F).Installing the batteries1Squeeze the battery-holder tabs inward (in the direction of the arrows) and slide out the battery holder.2Insert new batteries, making sure the polarities are correct, and then return the battery holder to its original position.Battery indicationThe power status is indicated by eight level indications. Replace both batteries when the battery indication starts to flash.Be sure to check the expiration date printed on the new batteries before using them.
The indication is based on the use of new LR6 (size AA) Sony Alkaline batteries. An incorrect indication may result when a different kind of batteries, a different brand of batteries or old batteries are used. If you plan to use the transmitter for a long period of time, it is recommended that you replace the batteries with brand new ones.Setting the Transmission ChannelThe transmitter provides groups of interference-free channels. When using multiple microphones and transmitters at the same time (simultaneous multi-channel operations) within the same area, selecting the same group and using a channel within that group can prevent signal interference.To set the transmission channel on the transmitter, first you select the group and channel using the RF indicator and scanning functions on the receiver. Next you set the group and channel parameters to match the setting on the receiver.Selecting the group/channel• Before doing this procedure, use the BAND function to set the transmitter to the bandwidth of the receiver you are using.• The setting for this function cannot be changed during actual signal transmission. Set the transmitter group (GP) and channel (CH) as follows:For details on groups and channels, refer to “Sony Digital Wireless Microphone System Frequency Lists” on the supplied CD-ROM.For details on menu operation, see “Basic Menu Operations”.NoteNotes
1Turn off the power, and then while holding down the SET button, turn the power on.The signal transmission stops.2Press the + or – button repeatedly until the GP/CH indication is displayed.3Hold down the SET button until the group indication flashes.4Press the + or – button repeatedly to select a group.5Press the SET button to enter the group.The channel indication starts flashing.6Press the + or – button repeatedly to select a channel.7Press the SET button to enter the channel.To set the group/channel using the pairing mode of the wireless remote control functionWhen the transmitter is paired with the receiver, the transmission channel of the transmitter is set to the receiving channel on the receiver automatically.For details, see“Pairing with a receiver”.Using the Wireless Remote Control FunctionThis transmitter is equipped with a wireless remote control function that can be used to set the parameters (low-cut filter, attenuation operation, power save mode, etc.) of the transmitter through the receiver or other devices. This function makes it easier to operate and manage the microphone system while in the field.This wireless control is 2.4 GHz IEEE802.15.4 compliant and has no effect on the RF band of digital wireless audio.This function is activated when pairing is established between the transmitter and the receiver using the RF REMOTE function. Pairing must be done first before the wireless remote control function can be used.Pairing with a receiverPairing links the transmitter with the receiver which the wireless remote control function is to be used.When the transmitter has been paired with a receiver through the receiver operation, turning on the transmitter while holding down the – button establishes the pairing immediately.To carry out pairing through menu operations on the transmitter, do the following.1Set the receiver to be used for controlling the transmitter to pairing mode.
For details on receiver operations, refer to the operating instructions supplied with the receiver.2Press the + or – button repeatedly until the RF REMOTE indication is displayed.3Hold down the SET button until the item to be set flashes.4Press the + or – button repeatedly to select PAIRING.5Press the SET button to enter.The transmitter sends a pairing request to the receiver which is on pairing mode.Before established pairing, if you press any operation key on the transmitter, pairing mode will be cancelled.When pairing has been established, the wireless remote control condition level (indicated by ) goes up, the RF REMOTE function turns on, and the remote control function becomes operative.To use the wireless remote control function with a previous pairingIn the RF REMOTE indication, select ON.• When you set RF REMOTE to ON, the transmitter will communicate with the receiver to which it was previously paired. To use the wireless remote control function with another receiver, you must perform the pairing procedure for that receiver.• Multiple transmitters cannot be paired with the same receiver. The following transmitter settings can be done from the wireless remote control:• Group/channel/BAND setting• RF transmission power setting• Attenuator for the audio input setting• Low-cut filter setting• Power save setting• +48 V power supply settingFor details on menu operation, see “Setting Menus”.To cancel the wireless remote control functionIn the RF REMOTE indication, select OFF.Notes on the wireless remote control functionThe wireless remote control function on the transmitter uses the 2.4-GHz band and may thus be subject to interference from other devices.• When pairing fails (“Pairing fail” is displayed), successful communication between the transmitter and the receiver has not occurred within a given amount of time. Pairing may be harder to do when another receiver is engaged in pairing nearby. • When it becomes hard to use the remote control, the remote control may be improved by switching the wireless remote control function off, then on again in the RF REMOTE indication, then re-pairing with the transmitter (change to a channel with less interference).Notes
Using the EncryptedTransmission FunctionTo prevent hacking of the signal, the transmitter scrambles the signal during transmission. To use this function, select one of the following encrypted transmission modes:Secure key mode: An encryption key that is automatically generated by the transmitter is used by both the transmitter and receiver in this one-to-one encrypted transmission method.Password mode: You choose a password of up to eight characters that can be set for multiple transmitters and receivers. This enables encrypted transmission within a group. Make sure the same mode is set on the transmitter and receiver.Using secure key mode (SECURE KEY)Use this mode for one-to-one encrypted transmission between one transmitter and one receiver.An encryption key that cannot be read from the outside is automatically generated by the transmitter. This key is transmitted to the receiver through a USB connection or the RF REMOTE function, enabling encrypted transmission to take place.The encryption key used by the transmitter and receiver is newly generated for each key transmission, resulting in highly secure communication.The encryption key used between the transmitter and the receiver is saved when the power is turned off, so the encrypted transmission can be resumed the next time the power is turned on.1Preparing the transmitter (this unit)1Hold down the SET button until the item to be set flashes in the ENCRYPTION indication on the transmitter.2Press the + or – button repeatedly to select SECURE KEY, and then press the SET button.2Preparing the receiverSelect SECURE KEY on the receiver that receives the encryption key.For details on receiver operations, refer to the operating instructions supplied with the receiver.3Exchanging the encryption keyOn the receiver, select USB or REMOTE (wireless remote) as the method for encryption key exchange.When the RF REMOTE function is off, REMOTE cannot be selected.When you select USB: Connect the transmitter to the receiver with the supplied USB cable and USB adapter cable.Note
For details on receiver operations, refer to the operating instructions supplied with the receiver.When you select REMOTE: The transmitter searches for a receiver that it has been paired with. After the transmitter detects the receiver, the transmitter exchanges the encryption key with receiver and encrypted transmission begins.Using password mode (PASSWORD)Set this mode when multiple transmitters are paired with multiple receivers for encrypted transmission.If both transmitters and receivers are set with the same user-designated password, the audio signal can be decoded. This mode is useful when multiple transmitters and receivers are used as a single group, or when the audio signal from one transmitter is received by multiple receivers at the same time.1Hold down the SET button until the item to be set flashes in the ENCRYPTION indication on the transmitter.2Press the + or – button repeatedly to select PASSWORD, and then press the SET button.3Input a password of up to eight characters on the transmitter.To enter a password, use the procedure described in “Naming of transmitter (NAME)” on page 25.4Set the encrypted transmission function setting on the receiver to PASSWORD.5Set the same password that was set on the transmitter.For details on receiver operations, refer to the operating instructions supplied with the receiver.It is recommended that you change the password periodically.USB cable (supplied)USB adapter cable (supplied)Note
Using a USB KeyboardConnecting an optional USB keyboard to the transmitter allows you to perform menu operations and enter your name and password for the encrypted transmission function from the keyboard.A Micro USB connector is used on the transmitter. For this reason, use the supplied USB adapter cable.Menu operations with a USB keyboardYou can use a USB keyboard to perform the same menu operations that you do on the transmitter.The transmitter buttons correspond to the following keys on a USB keyboard:To enter a textWith a USB keyboard, you can enter names and passwords for encrypted transmissions.Characters that can be entered from a USB keyboard: (space), 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, B, C, D, E, F, G, H, I, J, K, L, M, N, O, P, Q, R, S, T, U, V, W, X, Y, Z, !, #, &, $, @, +, -, =, _, (, ), [, ](Passwords may consist of the numbers 0 to 9 and letters A to Z only.)Special key: Backspace (BS) and Delete (DEL) keys. • The number keys on the keyboard cannot be used.• This transmitter is compatible with English-language keyboards only.• USB keyboards with multiple functions, such as USB hub and pointing device, cannot be used.• Power to the connected keyboard is supplied by the USB connector on the transmitter. The power rating is 100 mA. Keyboards that consume more power than that cannot be used.• Do not leave the transmitter connected to the keyboard when not in use. If you do, the batteries in the transmitter will be drained more quickly.• Text editing should be done with the alphabet, BS, DEL, and Enter keys.Buttons on the transmitterUSB keyboardSET ENTER+R–rUSB adapter cable (supplied)Notes
Basic Menu Operations1Press the + or – button repeatedly until the function to be set appears.2Hold down the SET button until the item to be set flashes.3Press the + or – button to change the setting.4Press the SET button to enter the setting.Types of menu:• NAME (transmitter name) setting • BAND (frequency band) selection• GP/CH (group/channel) selection• RF POWER (RF transmission power) setting• INPUT LEVEL (audio input level) setting• LCF (low-cut filter) setting• POWER SAVE setting• TIME (accumulated use time) indication• +48V (+48 V power supply) setting• ENCRYPTION (encrypted transmission function) setting• INTERNAL SG (internal signal generator)• POWER SW LOCK (POWER switch lock) function• RF REMOTE (wireless remote control) function• BRIGHTNESS (display brightness) setting• DIMMER MODE (automatic dimming of the display) setting• FACTORY PRESET (factory setting) function• VERSION (software version) indicationFunction nameItem to be set
Setting MenusThe functions and parameters of the settings menu are explained here. Underlined items are the factory setting.Naming of transmitter (NAME)You can specify a transmitter name of up to 16 characters. The factory setting for the transmitter name is the model name and serial number. The transmitter name is sent to the receiver as metadata and is used by the receiver to distinguish between different transmitters.+: The first press on the + button displays the character set. You can then use the + and – buttons to select the desired character. And then, pressing the SET button adds the selected character to the end of the current name.– : Deletes the last character in the current name.SET: Enters the character or edited name.You cannot insert or delete a character in the middle of the name.To edit with a keyboardYou can enter data from an optional keyboard connected to the USB connector.For details, see “Using a USB Keyboard”.Selecting the group/channel (GP/CH)The factory settings are as follows:00 GpFor details, see “Selecting the group/channel”.Selecting the frequency band (BAND)Match the frequency range on this transmitter to that of the Sony digital wireless receiver.The frequency range that can be set for the optional receiver combined with this transmitter differs as follows: ExampleTV30-33, TV34-36, TV38-41Not available for TV376267CETV62-64, TV67-69Not available for TV65 and TV66For details on the frequency range of each band, refer to “Sony Digital Wireless Microphone System Frequency Lists” on the supplied CD-ROM.Using wireless remote control, this function can be controlled from the receiver and other devices.For details on wireless remote control function, see “Using the Wireless Remote Control Function” on page 19.Note
The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the transmitter first. Then, while holding down the SET button, turn the power on. And then, change the setting after the signal transmission has stopped.Setting the RF output power (RF POWER)You can set the RF output power.1 mW (LOW): Transmitted by 1 mW10 mW (MID): Transmitted by 10 mW50 mW (HIGH): Transmitted by 50 mW Using wireless remote control, this function can be controlled from the receiver and other devices.For details on wireless remote control function, see “Using the Wireless Remote Control Function”.The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the transmitter first. Then, while holding down the SET button, turn the power on. And then, change the setting after the signal transmission has stopped.Setting the audio input level (INPUT LEVEL) You can set the input level to an analog head amp.Select LINE or MIC, depending on the audio source connected to the audio input connecter.When MIC is selected, ATT (attenuation level) will flash next. With the microphone connected, speak into the microphone as you monitor the audio input level meter and press the + or – button repeatedly to select the appropriate attenuation level.The reference levels for the various settings are as follows:With the wireless remote control function, the attenuation level can be changed from the receiver and other devices.For details on wireless remote control function, see “Using the Wireless Remote Control Function”.Note NoteInput Attenuation (dB)Reference input level (dB)Maximum input level (dBu)Headroom (dB)MIC 0–58 –22 363–55 –196–52 –169–49 –133 dB step 3 dB step 3 dB step45 –13 +2348 –10 +24 34LINE –+4 +24 20
Low-cut filter setting (LCF)The frequency of the low-cut filter can be set.OFF:Turns off the low-cut filter.20 30 40 50 60 70 80 90 100120 140 160 180 200 220 (Hz): Low-cut filter is set according to the selected frequency.Using wireless remote control, this function can be controlled from the receiver and other devices.For details on wireless remote control function, see “Using the Wireless Remote Control Function”.Power save setting (POWER SAVE)To conserve power, this setting allows you to put all transmitter functions to sleep.ACTIVE:The transmitter operates normally.SLEEP: The sleep function is on. During sleep, the POWER indicator flashes at 2-second intervals.To change back to normal operationDuring sleep, press the SET, +, or – button.You can also use the wireless remote control to change the receiver back to normal operation.For details on wireless remote control function, see “Using the Wireless Remote Control Function”.Displaying the accumulated use time (TIME)You can display the accumulated battery use time as a rough estimate of total transmitter usage.The factory setting is “00:00”.To reset the accumulated time indication1Hold down the SET button until the time indication flashes.2Press the – button so “00:00 RESET” appears, and then press the SET button.+48 V power supply setting (+48V)You can turn the +48 V power supply on or off for microphones that require an external power supply.OFF:Power is not supplied to the connected microphone.ON: Power is supplied to the connected microphone.Using wireless remote control, this function can be controlled from the receiver and other devices.For details on wireless remote control function, see “Using the Wireless Remote Control Function”.The +48 V power supply can be turned on or off, regardless of INPUT LEVEL setting. Note, however, that the +48 V power is actually supplied only when INPUT LEVEL is set to MIC.Note
Setting the encrypted transmission function (ENCRYPTION)You can set the encrypted transmission function.SECURE KEY: Sets the secure key method.PASSWORD: Sets the password method.OFF: The encrypted transmission function is not used.For details, see “Using the Encrypted Transmission Function”.Generating an internal signal (INTERNAL SG)This transmitter generates a 1-kHz reference level sine wave that can be used to adjust or check the audio level of the receiver or the system that you are using. This internal signal is outside the control of the attenuator.1 kHz: A 1-kHz internal signal is generated.OFF: An internal signal is not generated.If the transmitter is turned off while INTERNAL SG is set to 1 kHz, the setting will revert to OFF automatically.Locking the POWER switch (POWER SW LOCK)The POWER switch can be locked to prevent the transmitter from being accidentally turned off or on.Even when the POWER switch is locked, all parts of the transmitter other than the POWER switch remain functional.UNLOCK:The POWER switch is not locked.LOCK: The POWER switch is locked.When LOCK is selected, the POWER switch lock indicator appears in the display.Wireless remote control function (RF REMOTE)This function must be set to allow the wireless remote control function to be used between the transmitter and receiver.OFF: Stops the wireless remote control function.ON: Starts the wireless remote control function with the previously paired receiver.PAIRING: Executes a new pairing.For details, see “Pairing with a receiver”.Setting the brightness of the display (BRIGHTNESS)Ten levels of brightness can be selected for the organic light-emitting diode display.The selectable settings are the following:(Dark) 1 2 3 4 5 6 7 8 9 10 (Bright)Automatic dimming of the display (DIMMER MODE)The organic light-emitting diode display can be set to dim or turn off after a certain amount of time.AUTO OFF: The display turns off after 30 seconds. The display goes on again when you press the SET, +, or – button.AUTO DIMMER: The display dims after 30 seconds. The display becomes bright again when you press the SET, +, or – button.Note
ALWAYS ON: The display stays on at the brightness level set with the BRIGHTNESS function.Resetting parameters to their factory settings (FACTORY PRESET)All parameter settings can be returned to their factory settings.Holding down the SET button until a message appears asking for confirmation. Press the + or – button repeatedly to select YES, and then press the SET button to enter. The transmitter parameters are reset to their factory settings. The setting for this function cannot be changed during actual signal transmission. To change the setting, turn off the power first. Then while holding down the SET button, turn the power on. And then, change the setting after the signal transmission has stopped.Displaying the software version (VERSION)The version of the transmitter software can be displayed.Note
TroubleshootingIf you encounter a problem using this transmitter, use the following checklist to find a solution. For any problems with the receiver or adapter, refer to the operating instructions supplied with the respective device. If the problem persists, consult your Sony dealer.Symptom Meanings RemedyThe transmitter does not turn on.The batteries are inserted backwards in the battery compartment.Reinsert the batteries with the correct orientation.The batteries are exhausted. Replace the batteries with new ones.The batteries drain quickly.Manganese batteries are being used.Use alkaline batteries.The transmitter is being used under cold conditions.The batteries drain quickly under cold conditions.Interruptions in the reception occurs.The transmitter is too far from the receiver.Decrease the distance to the receiver and check the reception. The RF output power setting is set to 1 mW (LOW).Increase the RF output power.There is no sound.The channel setting on the transmitter is different from that on the receiver.Use the same channel setting on both the transmitter and receiver.The setting of the encrypted transmission function on the receiver is different from that on the transmitter.Confirm that the setting of the encrypted transmission function is the same on both the transmitter and the receiver.The sound is weak. The audio input level of the transmitter is set to LINE or the attenuation level is too high. If a microphone is connected to the transmitter, set the audio input to MIC. While monitoring the audio input level meter, set the attenuator to an appropriate level.There is distortion in the sound. The attenuator is set too low for the audio input level of the transmitter. While monitoring the audio input level meter, set the attenuator to a level that does not produce distortion.The bass is weak.The frequency of the low-cut filter is set too high.While monitoring the sound, decrease the low-cut filter frequency to a level that produces the proper sound quality.
There is too much bass.The microphone connected to the transmitter produces excessive bass because the frequency response of the transmitter extends into the low 20-Hz range.Use the low-cut filter to cut the bass.The power does not turn off even though the POWER switch is turned to OFF.The POWER switch is locked. Turn off the POWER switch locking function.Wireless remote control is not possible.Pairing has not been established between the transmitter and receiver.Carry out pairing (see page 19).The receiver is too far from the transmitter for communication to occur.Check the wireless remote control condition level. If it is low, decrease the distance between the transmitter and the receiver.The transmitter that was paired with the receiver has been paired with another receiver.On the receiver, carry out pairing again with the transmitter that you want to control.The USB keyboard does not work.You are using a USB keyboard that is not compatible with the transmitter.Check the conditions for using a USB keyboard with the transmitter.The display is too dark.The display brightness is set to low.Adjust the brightness of the display.Symptom Meanings Remedy
Important Notes on OperationNotes on using the transmitter• The digital wireless microphone system product must be used within a temperature range of 0°C to 50°C (32°F to 122°F).• Operating the transmitter near electrical equipment (motors, transformers, or dimmers) may cause it to be affected by electromagnetic induction. Keep the transmitter as far from such equipment as possible.• The presence of the lighting equipment may produce electrical interference over the entire frequency range. Position the transmitter so that interference is minimized.• To avoid degradation of the signal-to-noise ratio, do not use the transmitter in noisy places or in locations subject to vibration, such as the following:- near electrical equipment, such as motors, transformers or dimmers- near air conditioning equipment or places subject to direct air flow from an air conditioner- near public address loudspeakers- where adjacent equipment might knock against the tunerKeep the transmitter as far from such equipment as possible or use buffering material.On cleaning• If the transmitter is used in a very humid or dusty place or in a place subject to an active gas, clean its surface as well as the connectors with a dry, soft cloth soon after use. Lengthy use of the transmitter in such places or not cleaning it after its use in such places may shorten its life.• Clean the surface and the connectors of the transmitter with a dry, soft cloth. Never use thinner, benzene, alcohol or any other chemicals, since these may mar the finish.Notes on simultaneous multi-channel operation• Keep the transmitter at least 30 centimeters (11 7/8inches) away from another transmitter.• When only digital wireless microphones are being used, keep the transmitter at least 4 meters (13 feet) away from the antenna of a receiver for up to 10 channels, and at least 6 meters (20 feet) away for 11 or more channels.• When a mixture of digital and analog wireless microphones is being used, keep the transmitter at least 6 meters (20 feet) away from the antenna of a receiver.• This system should be kept at least 100 meters (328 feet) away from any analog wireless systems using the same frequency when both are being used in a wide area with no walls or obstructions.• If you experience noise, increase the distance between the transmitter and receiver or decrease the transmission power on the transmitter.Note on microphone and transmitter combinationsIt is recommended that you use the Sony ECM-673/674/678 Electret Condenser Microphone with this transmitter. The transmission signal may cause noise on some microphones. If you experience noise,
you may be able to reduce it by lowering the transmission power. SpecificationsTransmitting sectionOscillator typeCrystal-controlled PLL synthesizerCarrier frequencies 470.125 to 607.875 MHz 614.125 to 697.875MHzU4250: 638 to 698 MHz (TV-42 to TV-51 channels)European model: CE6267: 798 to 822 MHz (TV-62 to TV-64 channels); 838 to 862 MHz (TV-67 to TV-69 channels)Channel step : 125kHzEuropean model: CE6267: 25 kHzRF power output1 mW/10 mW/50 mW (e.r.p) selectableOccupied RF bandwidth192 kHz or lessAudio delay1.5 msTransmission frequency stability level±6.5 ppmType of emissionG1E or G1DModulation methodπ/4 Shift QPSKAudio sectionMaximum input levelMIC: –22 dBu (with 0 dB attenuator)LINE: +24 dBuTo prevent electromagnetic interference from portable communication devicesThe use of portable telephones and other communication devices near the DWT-P01 may result in malfunction and interference with audio signals. It is recommended that portable communication devices near the DWT-P01 be turned off.
Audio attenuator adjustment range (pad) 0 to 48 dB (3-dB steps, MIC input mode only)Microphone input connectorXLR-3-11C (female)Input impedance4.7 kohms or moreFrequency response20 Hz to 22 kHzT.H.D 0.03% or lessDynamic range106 dB or more0 dBu = 0.775 VGeneralOperating voltage3 V DC, with two LR6 (AA) alkaline batteriesBattery lifeContinuous operating time 3.5 hours (at 25 °C (77 °F), 10-mW output using Sony LR6 (AA)-size alkaline batteries with the wireless remote control function off, DIMMER MODE set to AUTO OFF, and +48V set to OFF)Operating temperature0 to 50 °C (32 to 122 °F)Storage temperature–20 to +60 °C (–4 to +140 °F)Wireless remote control2.4-GHz 1EEE802.15.4 compliantDimensions (unit: mm (inches))Mass Approx. 245 g (8.6 oz) including batteriesSupplied accessoriesSpare battery case (1)Soft case (1)USB adapter cable (1)USB cable (1)Operating Instructions (1)CD-ROM (1)Optional accessoriesECM-673/674/678 Electret Condenser MicrophoneDesign and specifications are subject to change without notice.

Navigation menu