Sony Group BM153 Bluetooth Module User Manual SPEC BM153 V4 6 10012013

Sony Corporation Bluetooth Module SPEC BM153 V4 6 10012013

Contents

BM153_User Manual_REV3

Product Specification Spec-BM153-V4.6 Page 1 of 7 www.sunitec-cn.com ® Features: • Bluetooth Spec. V3.0 (V2.1+EDR)Compliant • Class 2 type Output Power • Support Firmware Upgrade • USB 1.1 and UART Host Interface • Multi-Configurable I2S, PCM or SPDIF Interface • Integrated Switched-Mode Regulator • Integrated Battery Charger • Integrated Microphone bias • Integrated LED Driver • Built in 16-bit Stereo Codec- 95dB SNR for DAC • Factory configurable to either 1.8V or 3.3V supply. • Supports up to 32Mbits of External Flash Memory (16Mbits Typical Requirement) • Enhanced Audibility and Noise Cancellation • PCB material:FR4 • PCB Surface treatment: Immersion gold • Size: 21mm x 13.5 mm x 2.35mm • Weight: 0.8g System Architecture BM153 Class 2 Multimedia Module CSR, BC57E687C Jan. 2013 Product Description: The BM153 is a Class 2 Bluetooth sub-system using BlueCore5-Multimedia External chipset from leading Bluetooth chipset supplier Cambridge Silicon Radio. BM153 interfaces to 8Mbit of external Flash memory When used with the CSR Bluetooth software stack, it provides a fully compliant Bluetooth system to V3.0 of the specification for data and voice communications The module and device firmware is fully compliant with the Bluetooth specification V3.0 Applications: • Hands-free Car Kit • Stereo Headset • AV Headphones • Echo Cancellation • High Performance Mono Headsets • Analogue and USB Multimedia Dongles •Wireless Speakers Specifications: Operating Frequency Band 2.4GHz ~ 2.48GHz unlicensed ISM band Bluetooth Specification BT V3.0 (V2.1+EDR) Output Power Class Class 2 Max. Output Power 2.5mW Date Rate 3Mbps Channel No. 79 Modulation Type GFSK π/4 DQPSK 8DPSK Operating Voltage 1.8V / 3.3V Host Interface USB 1.1 or UART Audio Interface PCM, I2S, SPDIF Flash Memory Size 8M,16M, or 32Mbits Dimension 21mm (L) x 13.5 (W) mm x 2.35mm (H) Specifications are subject to change without prior notice Qualified
Product Specification Spec-BM153-V4.6 Page 2 of 7 www.sunitec-cn.com ® Electrical Characteristics Absolute Maximum Rating Min Max Storage Temperature -40°C +85°C Supply Voltage, (V_CHG) -0.30V +6.5V Recommended Operating Conditions Min Max Operating Temperature Range -20°C +70°C Supply Voltage, (V_BAT) 2.5V 4.2V Supply Voltage, (V_CHG) 4.5V 5.75V Power Consumption Units Average SCO Connection HV3 (30ms interval sniff mode) mA 21 SCO Connection HV1 mA 40 ACL Data Transfer 115.2Kbps UART no traffic (Master) mA 4.4 ACL Data Transfer 115.2Kbps UART no traffic (Slave) mA 15 CODEC Microphone inputs and ADC/channel mA TBD DAC and loudspeaker driver, no signal/channel mA TBD Digital audio processing subsystem mA TBD VBAT = 4.2V; f = 2.441GHz; T=20°C RF Characteristics Receiver Units Min Typ Max Bluetooth Spec Sensitivity at 0.1% BER dBm - -90 -86 ≤-70 Maximum Receiver Signal dBm -20 -10 - ≥ -20 C/I Co-Channel dB - 6 11 ≤11 Adjacent Channel Selectivity C/I -1MHz dB - -6 0 ≤0 2nd Adjacent Channel Selectivity C/I -2MHz dB - -38 -30 ≤-30 3rd Adjacent Channel Selectivity C/I -3MHz dB - -45 -40 ≤-40 Image Rejection C/I dB - -16 -9 ≤-9 VBAT = 4.2V; f = 2.4441GHz; T=20°C Transmitter Units Min Typ Max Bluetooth Spec RF Output Power dBm 0 3 - -6 to +4 RF Power Control Range dB 16 24 - > 16 RF Power Range Control Resolution dB - 0.5 - - 20dB Bandwidth for Modulated Carrier KHz - 940 1000 <1000 2nd Adjacent Channel Power (+/- 2MHz) dBm - -36 -20 ≤-20 3rd Adjacent Channel Power (+/- 3MHz) dBm - -45 -40 ≤-40 VBAT = 4.2V; f = 2.4441GHz; T=20°C All specifications including pinouts and electrical specifications may be changed without prior notice
Product Specification Spec-BM153-V4.6 Page 3 of 7 www.sunitec-cn.com ® Pin Configurations PIN NO. NAME TYPE FUNCTION RE-MARK 1 AIO1 Bi-directional Programmable input/output line 2 AIO0 Bi-directional Programmable input/output line 3 RESET CMOS input with weak internal pull-up Reset if low. Input debounced so must be low for >5ms to cause a reset 4 GND GND Ground 5 PIO9 Bi-directional Programmable Input/Output Line 6 PIO10 Bi-directional Programmable Input/Output Line 7 PIO11 Bi-directional Programmable Input/Output Line 8 PIO12 Bi-directional Programmable Input/Output Line 9 PIO13 Bi-directional Programmable Input/Output Line 10 PIO14 Bi-directional Programmable Input/Output Line 11 PIO15 Bi-directional Programmable Input/Output Line 12 GND GND Ground 13 VDD Power +3.3V Supply For 3.3V Version VDD Power Connect to +1V8 For 1.8V Version 14 VDD_USB Power Positive supply for UART/USB ports, Connect to VDD 15 +1V8 Power +1.8V Supply 16 GND GND Ground 17 USB_DP Bi-directional USB Data Plus 18 USB_DN Bi-directional USB Data Minus 19 UART_RTS CMOS Output UART Request To Send (Active Low) 20 UART_CTS CMOS Input UART Clear To Send (Active Low) 21 UART_RX CMOS Input UART Data Input (Active High) 22 UART_TX CMOS Output UART Data Output (Active High) 23 PCM_IN CMOS Input Synchronous Data Input 24 PCM_SYNC Bi-directional Synchronous Data Sync 25 PCM_CLK Bi-directional Synchronous Data Clock 26 PCM_OUT CMOS Output Synchronous Data Output 27 SPI_CSB CMOS Input Chip Select For Synchronous Serial Interface (Active Low) 28 SPI_MISO CMOS Output Serial Peripheral Interface Data Output 29 SPI_CLK CMOS Input Serial Peripheral Interface Clock 30 SPI_MOSI CMOS Input Serial Peripheral Interface Data Input 31 VRE_IN Analogue Take high to enable switch-mode regulator 32 VDD_BAT Battery terminal +ve Lithium ion/polymer battery positive terminal. Battery charger output and input to switch-mode regulator 33 GND GND Ground 34 VDD_CHG Charger input Lithium ion/polymer battery charger input 35 LED1 Open drain output LED Driver 36 LED0 Open drain output LED Driver 37 GND GND Ground 38 SPK_L_N Analogue Speaker output negative, left 39 SPK_L_P Analogue Speaker output positive, left 40 SPK_R_N Analogue Speaker output negative, right 41 SPK_R_P Analogue Speaker output positive, right 42 GND_S GND_S Anlogue Signal Ground 43 MIC_BIAS Analogue Microphone bias 44 MIC_B_P Analogue Microphone input positive, right 45 MIC_B_N Analogue Microphone input negative, right 46 MIC_A_P Analogue Microphone input positive, left 47 MIC_A_N Analogue Microphone input negative, left 48 GND GND Ground 49 PIO0 Bi-directional Programmable Input/Output Line 50 PIO1 Bi-directional Programmable Input/Output Line 51 PIO2 Bi-directional Programmable Input/Output Line 52 PIO3 Bi-directional Programmable Input/Output Line 53 PIO4 Bi-directional Programmable Input/Output Line 54 PIO5 Bi-directional Programmable Input/Output Line 55 PIO6 Bi-directional Programmable Input/Output Line 56 PIO7 Bi-directional Programmable Input/Output Line 57 PIO8 Bi-directional Programmable Input/Output Line 58 GND GND Ground 59 RF-IN RF RF Interface 60 GND GND Ground
Product Specification Spec-BM153-V4.6 Page 4 of 7 www.sunitec-cn.com ® Recommended Layout patterns:
Product Specification Spec-BM153-V4.6 Page 5 of 7 www.sunitec-cn.com ® Recommended Reflow Temperature Profile: Key features of the profile: -Initial Ramp=1-2.5℃/sec to 175℃ equilibrium -Equilibrium time=60 to 80 seconds -Ramp to Maximum temperature (250℃)=3℃/sec Max -Time above liquidus temperature(217℃): 45 - 90 seconds -Device absolute maximum reflow temperature: 250℃ MAC Address: Each Module has his MAC Address 001D DF XXXXXX Concerning the dimension of the tab，only printing the last six letters of the LAP on the module. xxxxxx5.0 mm13.0 mm The tab code pastes style:
Product Specification Spec-BM153-V4.6 Page 6 of 7 www.sunitec-cn.com ® QDL Certificate
Product Specification Spec-BM153-V4.6 Page 7 of 7 www.sunitec-cn.com ® Ordering Information No Items Ordering Code (Class 2) Description 1 BC05mm-ext Module-3V3 BM153 16Mbit Flash Operating Voltage is 3.3V 2 BC05mm-ext Module-3V3 BM153-08 8Mbit Flash Operating Voltage is 3.3V 3 BC05mm-ext Module-3V3 BM153-32 32Mbit Flash Operating Voltage is 3.3V 4 BC05mm-ext Module Test Kit BM153 TK Test kit base BM153 Document References References Version Specifications of the Bluetooth System V2.1+EDR, 26 July 2007 BlueCore5-Multimedia External Product Data Sheet CS-121064-DSP2 15 July 2008 Document History Revision Date HistoryDraft V0.1 2006-12-12 V1.0 2007-04-12 First release V2.0 2008-09-11 Update from Revision V1.0 V3.0 2008-09-19 Update from Revision V2.0 V4.0 2009-05-22 Update from V2.0+EDR compliant to V2.1+EDR compliant V4.1 2009-07-30 Update from printing MAC address “UAP” to “LAP” V4.2 2009-08-22 Remove BC57E687B-ITB-E4 from BOM V4.3 2009-12-02 Modify page 3 PIN OUT mistake (Swap AIO0 and AIO1) V4.4 2011-7-1 Add more order information V4.5 2011-12-19 Add more order information BM153-32 V4.6 2013-01-10 Add BM153 Test board Contact Information Sunitec Enterprise Co., Ltd. Head Office: 3F.,No.98-1,Mincyuan Rd Sindian City, Taipei County 231,Taiwan Tel: 886-2-82191696 Fax: 886-2-82191676 http://www.sunitec.com.tw China Factory: No.2,Qilin Road 2,Run Tang Ind., Dan-Keng Village Fu Ming Community, Guan-lan Town, BaoAn District, Shenzhen GuangDong China Tel: 86-755-29802983 Fax: 86-755-29802984 E-mail: sales@sunitec-cn.com or project@sunitec-cn.com Http://www.sunitec-cn.com
InterInterrnalPhotornalPhotoSPersoSPersoSonyCorporaonalAudioSy[Model:SRSonyCorporaonalAudioSy[Model:SRationystemS‐X5]ationystemRS‐X5
InterrnalPhotoSPersoSonyCorporaonalAudioSy[Model:SRationystemRS‐X5
AllisNextsok,fixedthet:fixedtheiroespeakerandonnetandbdfrontplasticackboard.asfccase.Asfolfollowphotolowphoto；
Noww，oneSRS‐‐x5isfixedOKK.asfollowpphoto.

FCC Statement Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The end host device should bear the label which indicate "Contains FCC ID:AK8BM153" or "Contains IC:409B-BM153".

Navigation menu