Somfy Systems SWF Sunis RTS Wirefree Sun Sensor 9020412 User Manual SUNIS RTS 9020412 Draft 3 6 17

Somfy Systems Sunis RTS Wirefree Sun Sensor 9020412 SUNIS RTS 9020412 Draft 3 6 17

User Manual

☆★Fig4SOMFY NA HEADQUARTERS(800) 22-SOMFY (76639)6100 Broken Sound Pkwy. N.W.(800) 22-SOMFY (76639)(800) 22-SOMFY (76639) Mississauga, Ontario L4W2R4(800) 66-SOMFY (76639)Copyright © 3/2017 Somfy Systems Inc./SAS. All rights reserved.OUTDOOR SUNIS RTS WIREFREE9020412GETTING STARTEDSafety:Before installing and using this product, please read these instructions carefu lly.and legislation in the country in which the product is being installed, and inform his customers of the operating and maintenance conditions for this product.Any use outside the field of application specified by Somfyinvalidates the warranty and discharges Somfy of all liability, as does any failure to comply with the instructions given herein.Before installing please check the compatibility of this product with the associated equipment and accessories. Specific safety advice: Never drop, knock, drill or submerge the SUNIS. Do not use abrasive products or solvents to clean the SUNIS RTS Do not clean it using a water spray or high pressure cleaning methods. Ensure that the receiver is kept clean and regularly check if it is operating correctly. ....■Wirefree, no electrician required ■Easily select from 8 levels for sun threshold setting■Long battery life ■ LED feed back for all functions■Compatible with full range of RTS exterior motors ■Ideal for new and existing installationsOverviewSUNIS RTS Specifications:Power In: AA Alkaline BatteryMaximum Range: 65 ft. under optimal conditionso o o oOperating Temperature: -4 F to 104 F (-20 C to +40 C)Introduction:The SUNIS RTS sun sensor provides control of yourRTS motorized products based on current sun lightlevels. It can provide maintenance free service for 5+years from 2 AA batteries. The precise sun level caneasily be selected with 8 possible levels of lightsensitivity. The sun function can be enabled/dis-abled via a Somfy Soliris RTS transmitter or MyLink.A Somfy Soliris RTS transmitter or MyLink must beprovided with each installation to enable/disable thesun function. Moreover, the installer must comply with current standards ■ DEMO mode for fast and easy testingWhat is in the box:1. Sunis RTS sensor with built in mounting base2. 2 AA alkaline batteries3. 2 mounting screwsOpening the Sunis RTS:Rotate the top clockwise to align the arrows on the base and sensor top Fig1. This will allow you to open thesensor by lifting the sensor top from the mounting base Fig 2.Batteries:Two AA AlkalineInstall the batteries paying attention to the polarityshown on the base Fig 2.If the batteries are good and installed correctly, theRED battery LED will blink just after the batteries areinstalled. Hint: You can also check if batteries are still good byremoving them and reinstalling and confirming thebattery LED blinks.Installation:For exterior use, the Sunis RTS must be mounted to avertical wall.Drill 2 holes 17mm apart Fig 3.1.Mount the Sunis RTS base with the up arrow facing upand the drain hole facing directly down Fig 3.2.IP34 rated for direct weather exposure (Must be mountedcorrectly as per mounting instructions)15291 Barranca ParkwayCALIFORNIAIrvine, CA 92618-2201P: F: (949) 727-3775SOMFY ULCEN Installer Manualwww.somfysystems.comwww.somfysystems.com SOMFY SYSTEMS INC121 Herrod Blvd.Dayton, NJ 08810P: NJ: (609) 395-1300F: (609) 395-1776 FLORIDASuite 14Boca Raton, FL 33487P: F: (561) 995-7502SOMFY Canada Division5178 Everest DriveP: CN: (905) 564-6446F: (905) 238-1491Fig 1Fig 2Fig 2BatteryRed LED1 2Fig 3.GreenProg LEDRedBatt LEDProg Button -Sun Level +Sun LevelGreen LEDLevel 5-8Red LEDLevel 1-4The mounting location is critical Fig 4. Mount the Sunis RTS facing the direction the awning/screen protectsfrom sun. Ensure it is clear from obstruction that couldshade it through out the day.Programming:Programming ButtonAdding the Sunis RTS to the motor(s):Step 1: Press the programming button on the RTS transmitter for 3+ sec until the motor jogs. Fig 5Step 2: Press the Prog button on the Sunis RTS. Fig 6The green Prog LED will light and the motor will jog. The Sunis RTS has been added to the motor.Deleting the sensor - Repeat steps 1 and 2 above.Hints:A Soliris transmitter or MyLink must be programmed to the motor(s) to allow the user to Enable/Disable the sun Function.If a sensor is removed or damaged, it must be cleared from the motor memory.To delete all sensors when adding a new sensor, followsteps 1 and 2 above except on step 2 hold the prog button until the motor jogs twice (approx 7 sec). This Will clear all sensors. Repeat steps 1 and 2 normally toadd the new sensor.Setting Sun Threshold Level:The Sun Threshold level can be adjusted up or down bya short press of the + or - button. For levels 1-4 the orange LED will blink 1 - 4 times to confirm the level.For levels 5-8 the green LED will blink.DEMO Mode:Demo mode allows the Sunis RTS to be more easily tested by reducing the delay times. Pressing the + & -together will cause the Sunis to cycle in or out of Demo.The Red and Green LEDs will alternate when enteringDemo mode and blink together when exiting. The SunisWill automatically time out of Demo mode in 3 min. Fig 5 Fig 6Thresholds 12345678Sunlight intensity (kLux)1 5 10 20 40 55 75 100LED active Red GreenNumber of flashes ☆☆ ☆☆ ☆ ☆☆ ☆ ☆ ☆★★ ★★ ★ ★★ ★ ★ ★IncreaseThresholdDecreaseThresholdTime Delays No Sun SunDemo Mode 15 sec 10 secNormal Mode 15-30 min 2 minThis device complies with Part 15 of the FCC Rules. Operation is - This device may not cause harmful interference and- This device must accept any interference received, including Warning! Changes or modifications not expressly approved by the subject to the following conditions:interference that may cause undesired operationmanufacturer could void the users authority to operate the equipment.FCC:IC statements:- This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesiredOperation of the device.- Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.Sun Sensor

Navigation menu