Somfy Systems SRS Solar Rain Sensor SRS-10 9019617 User Manual RTS rain sensor instr full FCC

Somfy Systems Solar Rain Sensor SRS-10 9019617 RTS rain sensor instr full FCC

Users Manual

2.088”[53.04] 4.479”[113.77] 2.590”[65.79]Instructions Somfy Solar Rain Sensor (SRS) - RTSON1234RAINDEMOSUNPROG1 - Open the hatch by pressing the latch toward the hatch and pulling outward (Fig 1)2 - Inside the hatch you will see the Rain and Sun threshold adjustment pots, the DEMO and Program Buttons and the Mode Dip Switches (Fig 2).3 - Do not remove the sticker over dip switches 3 and 4. Only Dip switches 1 and 2 will be used to select the Mode for normal Awning use.4 - Select the desired mode using dip switches 1 and 2. Dips 3 and 4 should remain off.StickerHatchLatchFig 1Fig 2ON1234ON1234ON1234Awning Rain Awning Rain & SunAwning Sun5 - In Awning Rain mode (A), the SRS will run the awning in when the rain rate exceeds the set rain threshold.6 - In Awning Sun mode* (B), the SRS will run the awning in after about 15-30 min with the sun below the set sun threshold and out after about 2 min with the sun above the threshold.7 - In Awning Rain & Sun mode* (C), the rain and sun functions are both active but a rainevent will override the sun function until the rain rate falls below the set threshold for 5 min.8 - The Sun and Rain threshold adjustment pots can be turned 280 deg from the minimumsetting to the maximum. (Fig 3)9 - The Rain threshold (Fig 4) can be set from: Min (fully CCW) = Very Light Rain/Heavy Mist/Heavy Condensation Max (fully CW) = Very Heavy Rain. 10 - The Sun threshold (Fig 5) can be set from Min (fully CCW) = approx 0.5klux - Facing sun with heavy cloud cover Max (Fully CW) = approx 55klux - Facing direct summer sun with no cloud cover11- LED indicators, The rain and sun LEDs will blink when conditions are above thethreshold, continuously in DEMO mode and every 5 sec in normal mode. Factory Default settings:A CB+-SUNMaxMin+-RAINMin Max+-Min Max280 degPOTAdjRangeFig 4 Fig 5Fig 3ON1234Awning RainA+-SUNMaxMin+-RAINMin MaxApprox 9:00Light Rain Approx 12:00Facing Sun, Light Cloud CoverImportant: If the RTS Rain and Sun sensor is removed from a job site it must be deleted from the motor memory.(see next section) Sun LEDRain LEDMode and Threshold Selection - AwningON1234RAINDEMOSUNPROGStickerHatchLatchFig 1Fig 2ON1234ON1234ON1234Awning Rain Awning SunA CB+-SUNMaxMin+-RAINMin Max+-Min Max280 degPOTAdjRangeFig 4 Fig 5Fig 3ON1234Awning RainA+-SUNMaxMin+-RAINMin MaxApprox 9:00Light Rain Approx 12:00Facing Sun, Light Cloud CoverIMPORTANT - Read the entire instructions and ensure the unit is charged before starting installation (see installation section)Sun LEDRain LEDNote; In order for the SRS to activate a motor in response to sun, the sun function of the motor must be enabled. To enable this feature, a Soliris Transmitter must be used and therefore programmed to the motor.This device complies with Part 15 of the FCC Rules. Operation is subject to the following conditions- This device may not cause harmful interference and- This device must accept any interference received, including interference that may cause undesired operationWarning! Changes or modifications not expressly approved by the manufacturer could void the users authority to operate the equipment.
Mode and Threshold Selection - Shutter/Screen (S/S)ON1234RAINDEMOSUNPROG1 - Open the hatch by pressing the latch toward the hatch and pulling outward (Fig 1)2 - Inside the hatch you will see the Rain and Sun threshold adjustment pots, the DEMO and Program Buttons and the Mode Dip Switches (Fig 2).3 - Remove the sticker over dip switches 3 and 4. 4 - Select the desired mode using dip switches 2, 3 and 4. Dip switch 1 should remain off.StickerHatchLatchFig 1Fig 2ON1234ON1234ON1234Shutter/Screen Rain S/S Rain & AutoS/S Rain & Sun5 - In S/S Rain mode (E), the SRS will send a down command when the rain rate exceeds the set rain threshold and will not send another rain command until the rain falls below therain threshold for 5 min and then goes above the threshold again..6 - In S/S Rain & Sun mode (F), Rain functions as per Mode E. A rain event will lock out the sun function until it falls below the threshold for 5 min. Sun light detected over the sun threshold for 2 min will cause a down (out) command. Sunlight under the threshold for 15min will cause an up (in) command7 - In S/S Rain & Auto mode (G), Rain functions as per Mode E. When the rain falls below the rain threshold for 5 min continuous, the sensor will send an automatic up command.8 - The Sun and Rain threshold adjustment pots can be turned 280 deg from the minimumsetting to the maximum. (Fig 3)9 - The Rain threshold (Fig 4) can be set from: Min (fully CCW) = Very Light Rain/Heavy Mist/Heavy Condensation Max (fully CW) = Very Heavy Rain. 10 - The Sun threshold (Fig 5) can be set from Min (fully CCW) = approx 0.5klux - Facing sun with heavy cloud cover Max (Fully CW) = approx 55klux - Facing direct summer sun with no cloud cover11- LED indicators, The rain and sun LEDs will blink when conditions are above thethreshold, continuously in DEMO mode and every 5 sec in normal mode. Factory Default settings:E GF+-SUNMaxMin+-RAINMin Max+-Min Max280 degPOTAdjRangeFig 4 Fig 5Fig 3ON1234Awning RainA+-SUNMaxMin+-RAINMin MaxApprox 9:00Light Rain Approx 12:00Facing Sun, Light Cloud CoverImportant: If the RTS Rain and Sun sensor is removed from a job site it must be deleted from the motor memory.(see next section) IMPORTANT - Read the entire instructions and ensure the unit is charged before starting installation (see installation section)Sun LEDRain LED 2.088”[53.04] 4.479”[113.77] 2.590”[65.79]Instructions Somfy Solar Rain Sensor (SRS) - RTS
ON1234RAINDEMODEMO Button-When the rain or sun condition passes a set threshold for the delay time listed above the command (XX) is given. Rain present locks out sun functions and normal transmitters.- In DEMO mode the LEDs will blink when conditions are above the threshold. In normalmode the LEDs will blink every 5 sec if conditions are above the threshold.Sun LEDSUNPROGRain LEDInstallation - Initial Charge - The Somfy Solar Rain Sensor (SRS) RTS is solar powered. Before installationensure the unit has an initial charge by placing the unit with the solar cell facing direct sun light. The initial charge will take about 10 min in direct outdoor sun light.- Mounting Bracket - The mounting is released by pushing the bracket clips gently towardsthe main body of the control. The bracket can be used to mount the SRS to a vertical wall usingscrews or to a 2 inch mast pole using zip ties. For a vertical wall the bracket is placed flat face towards the wall. For a mast pole mount the curved face is mounted to the pole.- Mounting Location - The Sensor should be mounted in a clear unobstructed location with thesensor facing the sun in the same facing as the awning. The sensor must be mounted with clear exposure to the rain in the same facing as the awning.The sensor must be mounted with the clear cover facing upward as shown (correct mount), with the sensor face at an angle. This allows excess moisture to run off and clear debris from the face.NOTE - If the sensor is removed from a job site, it must be deleted from the motor’s memory. 12Front tabs into top slot 1Back tabs intolower slot 2Mast pole orientationVertical wall orientationVertical WallCorrect mountMountingBracketBracketClip*Before programming ensure the sensor is set to the desired mode (Modeselection - Step 4 on page 1) and ensure the unit is charged (see below) Adding the sensor1- Put the motor into learning mode by pressing the programming button onan already programmed transmitter until the motor jogs.2- Open the hatch on the sensor and press the programming button. The motor will jog.Deleting the sensorRepeat steps 1 and 2 above.ProgrammingON1234RAINDEMOProgramming ButtonSUNPROGHatchLatchStep 2

Navigation menu