Smart Device Technology DS830 DS830 User Manual Manual

Shenzhen Smart Device Technology Co., LTD DS830 Manual

Manual

Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 DS-830 V3.0 3G datasheet Doc. Modification History Version Description Date V1.0 Creation 2015-11-27
FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Chapter 1. Production General Description 1.1 General Description DS-830 control board combines multimedia decoding, LCD driver,Ethernet,HDMI,WIFI,3G, and TVin in one, supporting most current fashionable video and image format decoding, HDMI output and double eight LVDS driver ,which can drive variable TFT LCD panels ,greatly simplify system design of whole machine, SD card and locker SIM card booth, having stronger stability and suitable for high-definition network broadcast box, video advertising machine and frame advertising machine. 1.2 Features ◆ High integration density: Integrating USB/LVDS/Ethernet/HDMI/WIFI in one and simplifying design of whole machine. SD card can be inserted. ◆ Built-in PCI-E 3G module. Supporting Huawei, ZTE and multiple PCI-E 3G/4G module, more suitable for remote maintenance of advertising all-in-one machine, saving labor cost.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 ◆ Ample extended interfaces. 6 USB ports (4 pins,2 standard USB ports),3 extensible serial ports and GPIO/ADC ports, satisfying requirement of variable peripherals in the market. ◆ High definition. Maximum supporting 1080P decoding and variable LCD screens with LVDS signal. ◆ Completed function. Supporting function of portrait and landscape mode playing, video multi-screen, scrolling caption, timing switch, USB data input and so on. ◆ Convenient management.：Humanized playlist maker software, easy for advertising play management and control. Play log, easy for knowing the play. 1.3 Appearance and Interface Sketch Front/Back： ：
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Chapter 2. Basic Function List Main Hardware Index CPU A83T , Octa-Core，main frequency 2GHz Internal Memory 1/2G(optional) Built-in Memory EMMC 4/8/16/32G(optional) Built-in ROM 2KB EEPROM Decoding Definition maximum support 1080P Operating System Above Android 4.X Play Mode support loop, timing, inter-cut and variable play modes Network Support Ethernet、support WiFi、wireless peripheral extension Video Playing Support wmv、avi、flv、rm、rmvb、mpeg 、ts、mp4 etc. Image Format Support BMP、JPEG、PNG、GIF USB2.0 Ports 2 USB HOST、4 USB ports Serial Ports 3 serial ports GPS External GPS（optional）
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 WIFI、BT built-in WIFI，BT4.0（optional） 3G built-in WCDMA,EVDO,4G NetMosa,support voice call Ethernet 1，10M/100M self-adapting Ethernet SD Card Support SD card LVDS output 1 single/dual channel，can drive 50/60Hz LCD panel directly HDMI output 1, support 1080P output Audio And Video Output support left and right channels output, built-in dual 4R/20W,8R/10W amplifier RTC Real Time Clock Support Timing Switch Support System Upgrade Support local SD,USB upgrade The producted have external antenna, The max antenna gain is 5dBi. if youused other antenna, the FCC will be apply again.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Chapter 3.PCB Measurement And Interface Layout 3.1 PCB Measurement Chart
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 PCB：6 layers Measurement：146mm*100mm, thickness 1.6mm Screw hole specification：∮3.2mm x 4 3.2 Interface Parameter Definition ◆Power Input Port Use 12V DC power supply，only allowed from the DC power supply and power socket to power the board system，the plug of the power adapter DC IN specifications is D6.0, d2.0. without in a peripheral empty load cases,12V dc power supply to support the minimum current 600 mA.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Power socket interfaces are defined as follows，can use power panel power supply，the socket specifications is 6 pin 2.54 mm spacing. NO. Definition Property Description 1 VCC input 12V input 2 VCC input 12V input 3 GND ground electrode ground electrode 4 GND ground electrode ground electrode 5 VCC-5V input standby 5V input 6 STB output standby signal output ◆ Standby 5V input & standby signal output is used as standby power supply board，if want to do low standby power consumption，the standby 5V input & standby signal output signal respectively connected with the 5 v power supply board STB and PS_ON（the description of the two signals might be different from different suppliers of power supply board，Please refer to the actual）， If you don't need to do low standby power consumption,then no need to connect the 2 pins. ◆ BAT1 RTC Battery Port Used to install the clock battery，supply power to the system clock when power outages.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Images of welding is a 1.25 mm spacing of 2 pin wafer socket，to reduce the overall height of board，can choose welding standard 2032 battery socket NO. Definition Property Description 1 RTC input 3V input 2 GND ground electrode ground electrode ◆ MIC Port Please note that the MIC is positive negative connection，not reverse. NO. Definition Property Description 1 MIC- input MIC- 2 MIC+ input MIC+ ◆ Port Of Receiving Remote Control
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Images of welding is a remote control receiving head，the default three pin socket weld 2.54 mm spacing when out of the factory. NO. Definition Property Description 1 IR input remote control signal input 2 GND ground electrode ground electrode 3 VCC Power 3.3V output ◆ Work Indicating Lamps NO. Definition Property Description 1 LED_B blue lamp work indicating lamp 2 VCC power 3.3V output 3 LED_R red lamp standby indicating lamp ◆ The default support gongyang red blue double LED lights. ◆ LED/IR Port The position of remote control receiving and indicating light is shared（can choose welding 2.54 mm spacing of 7 pins socket）。
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 NO. Definition Property Description 1 LED_B output work indicating lamp 2 VCC power 3.3V output 3 LED_R output standby indicating lamp 4 ADC ADC input ADC button input 5 IR input remote control signal input 6 GND ground electrode ground electrode 7 3.3V power 3.3V output ◆ Backlight Control Port Use for LVDS screen backlight control，the 12V power supply current is not more than 1.5A，When using more than 19 inch screen or screen backlight power in more than 20W，backlight power supply electricity is taken from the other power plate，so as not to cause system instability.Backlight can make voltage is 5V，if other voltage, please add IO level conversion circuit. The 12V power supply only as a backlight power output, don't as a power input supply system. NO. Definition Property Description 1 VCC power 12V output 2 VCC power 12V output
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 3 BL-EN output backlight enable control 4 BL-ADJ output backlight brightness adjust control 5 GND ground electrode ground electrode 6 GND ground electrode ground electrode ◆ I/O Control Port Used for provide control signal input/output of peripherals，Level of 3.3V，ADC signal can be used to button control。 NO. Definition Property Description 1 VCC power 3.3V output 2 I/O input GPIO-1 3 I/O input GPIO-2 4 I/O output GPIO-3 5 ADC input / output ADC signal 6 GND ground electrode ground electrode ◆ LVDS Port Commonly used LVDS interface definitions，support single/ double channels，6/8 bits 1080P LVDS screen. Screen voltage can be choose by jumper cap，can choose to support 3.3V/5V/12V screen power supply. In order to avoid burning board and screen, please pay attention to the following： 1. Please make sure the specifications and power supply voltage of the screen is correct,the power supply of the board can meet the maximum current screen work accordingly
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 2.Please confirm the power of the jumper cap is correct by multimeter. Using jumper cap to select the power of the screen above, from top to bottom,in order：12V/5V/3.3V. NO. Definition Property Description 1 PVCC power output LCD power output，+3.3v/+5V/ +12V optional 2 3 4 GND ground electrode ground electrode 5 6 7 0-VN0 output Pixel0 Negative Data (Odd) 8 0-VP0 output Pixel0 Positive Data (Odd) 9 0-VN1 output Pixel1 Negative Data (Odd) 10 0-VP1 output Pixel1 Positive Data (Odd) 11 0-VN2 output Pixel2 Negative Data (Odd) 12 0-VP2 output Pixel2 Positive Data (Odd) 13 GND ground electrode ground electrode 14 GND ground electrode ground electrode 15 0-VNC output Negative Sampling Clock (Odd) 16 0-VPC output Positive Sampling Clock (Odd) 17 0-VN3 output Pixel3 Negative Data (Odd) 18 0-VP3 output Pixel3 Positive Data (Odd) 19 1-VN0 output Pixel0 Negative Data (Even) 20 1-VP0 output Pixel0 Positive Data (Even) 21 1-VN1 output Pixel1 Negative Data (Even) 22 1-VP1 output Pixel1 Positive Data (Even) 23 1-VN2 output Pixel2 Negative Data (Even) 24 1-VP2 output Pixel2 Positive Data (Even)
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 25 GND ground electrode ground electrode 26 GND ground electrode ground electrode 27 1-VNC output Negative Sampling Clock (Even) 28 1-VPC output Positive Sampling Clock (Even) 29 1-VN3 output Pixel3 Negative Data (Even) 30 1-VP3 output Pixel3 Positive Data (Even) ◆ TTL double-wire serial interface socket*2 The board raises two groups of ordinary double-wire serial interface，can support general serial port devices on the market，level of the serial port is 0V to 3.3V.If the abutting serial level higher than 3.3 V，must have the isolating circuit or level conversion circuit, otherwise it will burn out master and equipment. Notice： 1.If TTL serial port voltage can match or not, can't directly access MAX232,485 devices. 2.TX，RX connection if is correct. NO. Definition Property Description 1 GND ground electrode ground electrode 2 UART- RX input / output RX 3 UART- TX input / output TX 4 VCC power 3.3V output ◆ TTL four-wire serial interface socket *1 The board raises one group of ordinary four-wire serial interface，can support general serial port devices on the market，level of the serial port is 0V to 3.3V.If the abutting serial level higher than 3.3 V，must have the isolating circuit or level conversion circuit, otherwise it will burn out master and equipment. Notice： 1.If TTL serial port voltage can match or not, can't directly access MAX232,485 devices.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 2.TX，RX connection if is correct. NO. Definition Property Description 1 UART-RTS input /output RTS 2 UART-CTS input / output CTS 3 GND ground electrode ground electrode 4 UART-RX input / output RX 5 UART-TX input / output TX 6 VCC power 3.3V output ◆ USB The board has 2 USB standard interface，4 built-in USB serial port，used for peripheral extended，the default is HOST，power supply current is not more than 500mA，for the USB OTG port，can select Host/Device by the jumper cap position as below picture.
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 NO. Definition Property Description 1 VCC power 5V output 2 DM input / output DM 3 DP input / output DP 4 GND ground electrode ground electrode ◆ Touch Screen Port NO. Definition Property Description 1 VCC power 3.3V output 2 SCK input/output I2C clock 3 SDA input/output I2C data
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 4 INT input/output interrupt 5 RST input/output reset 6 GND ground electrode ground electrode ◆ LINE_IN interface NO. Definition Property Description 1 LIN input left channel audio input 2 RIN input right channel audio input 3 GND ground electrode ground electrode 4 NC empty unused ◆ Audio Port 1(External amplifier needed) NO. Definition Property Description 1 AL output audio output left 2 HS-MIC input detection of headset insert 3 GND ground electrode ground electrode
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 4 AR output audio output right ◆ Audio Port 2(can drive loudspeaker directly) NO. Definition Property Description 1 OUTP-R output audio output right+ 2 OUTN-R output audio output right+ 3 OUTN-L output audio output left- 4 OUTP-L output audio output left- ◆ Switch machine button interface NO. Definition Property Description 1 PWR-ON input a pin of an external light touch button 2 GND ground electrode another pin of an external light touch button ◆ Uboot update key
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 NO. Definition Property Description 1 Uboot input Connect uboot pin 2 GND gnd Connect uboot pin ◆ Other Standard Interfaces And Function: Memory Port SD/TF card data storage, maximum support 32G USB HOST port, support data storage, data input, USB, mouse keyboard, camera, touch screen etc. Ethernet Port RJ45 port support 100M wired network HDMI Port standard port support HDMI data output, maximum support 1080P Earphone Port standard port 3.5mmstandard port 3G Port PCI-E standard port support variable PCI-E 3G 4G module, Huawei, ZTE etc. SIM Card Port standard port support variable system（depend on 3G module）
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 Chapter 4. Electric Performance Project Min Typical Max Power voltage voltage -- 12V -- ripple wave -- -- 50mV Power voltage current 3A Power current (HDMIoutput,no other peripheral) working current -- 300mA 500mA standby current -- 17mA 20mA USB power supply current -- -- 500mA Power current(LVDS) 3.3V working current 400 mA 500 mA 5V working current 550 mA 1A 12V working current 580 mA 1A USB power supply current -- -- 500mA Total output current 3.3V 800mA Environment Relative -- -- 80%
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 humidity working temperature -20℃ -- 70℃ Remark 1：When connect the LVD screens，need to pay attention to select the right backlight working voltage 3.3V, 5V, 12V，the users cannot be applied to beyond the corresponding maximum current peripherals. Remark 2: When connect the LVD screens，the board of the whole working current and standby current depending on the connection screens，above form not listed. Chapter 5 Assembly Using Notice In the process of assembly use，please note the following points (and not limited to) problem. 一， Bare board and a peripheral short circuit problem. 二， In the process of installing fixed，avoiding the bare board deformation caused by fixed problems. 三， When connect the LVD screens，pay attention to the screen voltage, electric current if is coincident. Attention to the problem of screen socket 1 pin direction. 四， When connect the LVD screens，pay attention to the screen backlight voltage, electric current if is coincident.The backlight power is more than
Shenzhen smart device technology ,.LTD WEB: www.smdt.com.cn TEL: 0755-61662980 FAX:0755-26992201 20W, whether or not to use other power panel power supply. 五， Peripheral devices (USB, IO, etc) when installation，attention to the problem of peripheral IO level and current output。 六， A serial port when installation，pay attention to whether connect 232485 devices directly.TX，RX connection if is correct. 七， Whether the input power supply access on the power input interface，according to the total peripheral evaluation ，whether can meet the requirements of the input power supply voltage, electric current and so on. To eradicate facilitate the operation from a backlight socket for access to the power supply input power.

Navigation menu