Silverlit Toys TX0002G4-1208 Remote Controller for Toy User Manual 84602a EN 6L R14

Silverlit Toys Manufactory Ltd. Remote Controller for Toy 84602a EN 6L R14

Manual

EI-4097aTroubleshootingPhotos taking/ Video recordingPress the photographing button to take photo through the camera on the helicopter. The Photo taking indicator will flash when a photo is taken.Press the video recording button to start recording video. Press the button again to stop recording. The Video recording indicator will turn on during recording.When the memory card is full, the icon on the upper right corner of the screen will be changed to . Move/ remove the saved data from the internal memory before taking photos again. Symptom Cause CorrectionThe helicopter does not response. - The helicopter and/ or the transmitter is switch off ("OFF").- The battery of the helicopter is weak.- Set the power switch to "ON"- Recharge the battery of the helicopter.The video/ photo was not recorded.The icon on the upper right corner of the screen will be changed to .- The battery of the helicopter is weak.- The memory card is full.- Recharge the battery of the helicopter.- Move/ remove some photos/ videos.4 ENGLISHThe helicopter does not react, or react poorly to operation by transmitter.- PAIRING / SYNC Procedure is not yet completed or done.- Out of the control range of distance.- Tail rotor blade is deformed or distorted.- The transmission range is up to 50 meters in open space.- Replace the tail rotor blade with the spare one provided.Loss of control.- Reset by switch off both helicopter and transmitter then switch both on again.Transferring files to computerInserting and removing the MicroSDOpening stored photos and videos1. Be sure your Helicopter has been switched OFF. Remove MicroSD card from helicopter. Insert it into adaptor and then connect with computer. A pop-up window will appear.2. Enter the camera folder, find the image files to needed location. Copy the images or videos to your computer. OFF/CHGON34File and Folder TasksAddressI:\BackFile Edit View Favorites Tools HelpSearch FoldersOther placesMy ComputerMy DocumentsWhat do you want Windows to do?Removable Disk (I:)Copy DiscPlayMake a muvee with videoOpen folder ti view filesusing Windows Explorerusing muvee Reveal Seagate Editionusing Windows Media Playerusing Roxio Creator CopyOKCancelOFF/CHGON12MicroSD card(not included)1. Open the cover.2. Insert the MicroSD card (not included) with the gold-colored contacts facing up.3. Push gently the card until the card disengages from the Helicopter, and then pull it out of the slot.123 4&OFF/CHGONTransmitterHelicopterBattery Installation & ChargingPart Identification2 ENGLISHNote: 1. The helicopter can operate for about 4 - 5 minutes per every 60 - 80 minutes charging. 2. Before recharging the battery, wait 10 - 15 minutes for it to cool down.Note: When the power indicator on the transmitter starts blinking, replace the batteries.Transmitter Battery Installation (*Make sure the power switch is set to "OFF".)Charging Helicopter2. Insert 8 AA batteries in the battery compartment with correct polarity.3. Close the battery compartment.3. Switch on the transmitter. The charging process will begin automatically and the green helicopter low battery indicators (helicopter and transmitter) will light up. Unplug the charging plug after both charging indicators turn off, charging is completed.1. Open the battery compartment by loosening the screw.2. Switch off the helicopter. Insert the charging plug into the charging socket on the helicopter.Battery compartment cover Battery compartment coverST.TRIMPRESS TO OPENVIDEOPOWERAEROPLANELOW BATTERYPHOTOL ROFF/CHGONOFF/CHGONPower switchCharging SocketMain rotor bladesCameraTail rotorMicro SD SlotST.TRIMVIDEODISPLAY MODEPAIR ON OFFHELICOPTERLOW BATTERYPHOTOL RVideo recording indicatorDisplay on/off buttonPower/Pair indicatorPhoto taking indicator Helicopter Low battery indicatorPower switchTrimmer L and R buttonPhoto taken buttonENTER buttonMENU/BACK buttonDOWN buttonUP buttonVideo recording buttonST.TRIMPRESS TO OPENVIDEOPOWERHELICOPTERLOW BATTERYPHOTOL ROR1. Pull out the cover and take the charging plug from the transmitter or connect the USB recharge cable to a USB socket.ST.TRIML Rfig. 6ST.TRIML Rfig. 3- For controlling the sticks on transmitter, try not to push the sticks immediately any extreme positions. It should be like steering a bicycle rather than pressing computer game sticks.- For the novice pilot (after the trimming procedure is completed), it is highly recommended to focus exclusively on learning to control the throttle stick first. If the helicopter turns around by itself there is no need to keep it straight. For the first flight, it is important to learn to keep the helicopter at a constant altitude of around 1 meter with very gentle inputs on the throttle stick. Once the pilot masters this, he may start learning to take control with the direction stick.Flying Your HelicopterTip! Piloting hints2. Trimming the helicopter: - Gently push the throttle up to raise your helicopter about 0.5 to 1 meter high. - When the helicopter spirals (fig. 4) or keeps turning anticlockwise (fig. 5), press the right side of the yaw trim button ("R") repeatedly until the helicopter flies straight (fig.6).Spiral anticlockwiseKeep turning anticlockwiseSpiral clockwise- When the helicopter spirals (fig. 1) or keeps turning clockwise (fig. 2), press the left side of the yaw trim button ("L") repeatedly until the helicopter flies straight (fig. 3).Keep turning clockwise3. Flight control:- Put the helicopter on a smooth surface. Uneven floor surface will affect its lifting off.- Slowly increase the throttle.- Do not look at the transmitter but focus on the helicopter.- As soon as the helicopter leaves ground, reduce the throttle slightly. (In the worst case, helicopter will go back to the floor but that is better than crashing against the ceiling.)- Very gently add the throttle if the helicopter descends.- Very gently reduce the throttle if the helicopter ascends.- For turning, give short and small inputs to the direction stick. (Most beginners will easily overcontrol the helicopter.)4. Lift-off procedures (after trimming procedure):ENGLISH 3Hover upHover downForward BackwardST.TRIMPRESS TO OPENVIDEOPOWERHELICOPTERLOW BATTERYPHOTOL RWhen the helicopter flies steadily, slowly push the throttle stick up to make helicopter fly higher, or lower the stick a bit to make helicopter fly lower. Only small amounts of stick position change are required for smooth flying.Maintain the helicopter at a certain height. Push the direction stick toward left to turn the helicopter anticlockwise, and push the direction stick toward right to turn it clockwise.Maintain the helicopter at a certain height. Push the direction stick upward to fly the helicopter forward. Push it downward to fly the helicopter backward.Forward and backward flight:Hover up and down:Turn left and right:- If the helicopter is crashed, switched off the helicopter and the transmitter. Examine the helicopter and ensure it has no damage before switching them on again.- Don’t operate the helicopter under the direct bright light it will affect the control system of your helicopter.- Don’t cover the IR diodes of the transmitter as it will block the IR signal.- Don’t stick any other label onto the helicopter as it will affect receiving of IR signal.Tip! Operation hintsfig. 1fig. 2fig. 5fig. 4ST.TRIMPRESS TO OPENVIDEOPOWERHELICOPTERLOW BATTERYPHOTOL RST.TRIMPRESS TO OPENVIDEOPOWERHELICOPTERLOW BATTERYPHOTOL RProcedure for PAIR / SYNC the Helicopter and Transmitting2.4 GHz technology allows for many helicopters to run without signal interference. A connection, or pairing, must be made between the helicopter and the transmitter to function. Sometimes, the pairing will happen automatically. If it does not, or if the connection is lost then follow these steps to sync the helicopter and the transmitter. 1. Place the helicopter on the ground with the tail point towards you and the nose pointing away.Make sure the throttle stick is at the minimum position. 2. Turn the Power Switch button to 'ON' position both on the Helicopter and Transmitter, Red LED will then flash. 3. The Synchronize/Pairing procedure is automatically COMPLETED when you can see the Red LED light up solid (not blinking) on both Helicopter and Transmitter.Choose the place which meets the following condition:1. Indoor environment with calm air. Beware of the air circulation from the air-conditioner.2. Caution: There must not be any dangerous objects (electric fan, air-conditioner, reading lamp, etc) on the flight path.1. Flight environmentDelivery contentsENGLISH 1For ages 15+Ab 15 JahreA partir de 15 ansLeeftijd vanaf 15 jaarA partir de 15 añosDai 15 anni in suTransmitterST.TRIMPRESS TO OPENVIDEOPOWERHELICOPTERLOW BATTERYPHOTOL RInstructions manualThis helicopter is equipped with a LiPo rechargeable battery, please pay attention to the following cautions for safety use:- Do not dispose the battery in fire or heat.- Do not use or leave the battery near a heat source such as fire or heater.- Do not strike or throw the battery against hard surface.- Do not immerse the battery in water, and keep the battery in a cool dry environment.- When recharging, only use the battery charger specifically for that purpose.- Do not over-discharge the battery.- Do not connect the battery to an electrical outlet.- Do not directly solder the battery and pierce the battery with a nail or other sharp object.- Do not disassemble or alter the battery.- Charge the battery every 6 months.The crossed-out dustbin symbol indicates that batteries, rechargeable batteries, button cells, battery packs, etc. must not be put in the household waste. Batteries are harmful to health and the environment. Please help to protect the environment from health risks. Tell your children to dispose of batteries properly by taking them to the local collecting points. This way batteries are recycled safely.Waste Electrical and Electronic Equipment (WEEE)When this appliance is out of use, please remove all batteries and dispose of them separately. Bring electrical appliances to the local collecting points for waste electrical and electronic equipment. Other components can be disposed of in domestic refuse. Precautions, Warnings and StatementsWarning: Conversion or modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to operate the product.- The transmitter-charger is tailor-made for the LiPo rechargeable battery used in helicopter. Do not use it to charge any battery other than that in the helicopter.- Photographing or video recording should only take place with the consent from all involved parties.- Never take apart or attempt to modify the product. This could damage the product.- Helicopter piloting requires specific skills and should be learned under direct supervision of an experienced adult.- Never operate this product if it has damaged parts.- Attention! Do not fly the helicopter near persons and animals.- Do not fly the helicopter in the vicinity of water and power lines.- Always keep your eyes on the helicopter and prevent it from landing or crashing near your head, your body, or on other people.- Stand during operation in order to get out of the way of the helicopter quickly if necessary.- Always switch the helicopter and the transmitter off when not operating.- Warning! Do not touch the running rotors. Keep hands, hair and loose clothes away from moving parts to avoid injury.- Never hold or throw any objects into the running rotors.- Attention! Risk of eye injuries! Keep a safety distance of at least 1 metre.- Keep this instruction manual for future reference.Tip! Safety hintsThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:1)This device may not cause harmful interference, and2)This device must accept any interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equipment and receiver.- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.- Consult the dealer or an experienced radio/TV technician for help. FCC StatementsPower Supply : Rating : DC 12 V , 7.2 WBatteries : 8 x 1.5 V "AA"/LR6/AM3 (not included)Power Supply : Rating : DC 3.7 V , 24 WBatteries : 1 x 3.7 V LiPo Rechargeable Battery Pack (included)Capacity : 600 mAhSilverlit SAS, Espace Green Parc, Route de Villepecle, 91280 Saint Pierre du Perray / France.© 2012 Silverlit. All rights reserved.Battery requirement (Helicopter):Battery requirement (Transmitter):The normal function of the product may be disturbed by Strong Electro Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual.In case the function could not resume, please use the product in other location. HelicopterCare and Maintenance:- Always remove batteries from the product when it is not being used for a long period of time. (Transmitter only)- Regularly examine for damage to the plug, enclosure and other parts. In the event of any damage, the product must not be used with the transmitter charger until the damage has been repaired.- Wipe the product gently with a clean cloth.- Keep the product away from direct heat.- Do not submerge the product into water that can damage the electronic assemblies.Special notes:- Please read the operation instructions carefully prior to the first use.Notes:- Under the environment with electrostatic discharge, the product may malfunction and require user to reset the product.- New alkaline batteries are recommended to use in this product to obtain best and maximum performance.- This product must only be used with the recommended charger.Battery warnings:- Non-rechargeable batteries are not to be recharged.- Rechargeable batteries are to be removed before being charged. (Transmitter only) - Different types of batteries or new and used batteries are not to be mixed. (Transmitter only)- Only batteries of the same or equivalent type as recommended are to be used.- Batteries are to be inserted with correct polarity.- Exhausted batteries are to be removed from the product. (Transmitter only)- The supply terminals are not to be short-circuited.- Do not mix old and new batteries. (Transmitter only)- Do not mix alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium) batteries. (Transmitter only)This product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC.USB CableFor upload photo & video function of the plane may be disturbed by Strong Electro Magnetic Interference. If so, the plane need to do the steps again to re-connect to the PC. In case the function could not resume, please use the product in other location.Note: Memory card slot : MicroSD card (not included), up to 32GBFF

Navigation menu