Siemens RF380R02 RFID Reader 13.56 MHz User Manual SIMATIC RF300

Siemens AG RFID Reader 13.56 MHz SIMATIC RF300

Contents

SYH_RF300_76_Part 2

Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 157 5.4.2 SIMATIC RF350R 5.4.2.1 Features SIMATIC RF350R Characteristics Design ① Antenna connection ② RS-422 interface ③ Status display Area of application Identification tasks in assembly lines in harsh industrial environments; for external antennas (ANT 1, ANT 3, ANT 12, ANT 18, ANT 30) Note Reader requires external antennas Note that the RF350R reader is designed only for operation with external antennas and only works in conjunction with the antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30. 5.4.2.2 Ordering data for RF350R Table 5- 14 Ordering data for RF350R Article number RF350R with RS-422 interface (3964R) 6GT2801-4AB10
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 158 System Manual, 07/2017, C79000-G8976-C345-07 5.4.2.3 Pin assignment of RF350R RS422 interface Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.4.2.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 15 LED operating display on the reader LED Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the cur-rent error. You will find more information on error messages in the section "System diagnostics (Page 413)". 5.4.2.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window. 5.4.2.6 Metal-free area The RF350R reader does not have an internal antenna. Operation is not affected by mounting on metal or flush-mounting in metal. For information about the metal-free area required by the external antennas, refer to the corresponding section of the chapter AUTOHOTSPOT.
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 159 5.4.2.7 Technical specifications Table 5- 16 Technical specifications of the RF350R reader 6GT2801-4AB10 Product type designation SIMATIC RF350R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range • ANT 1 • 140 mm • ANT 3 / ANT 3 S • 50 mm / 20 mm • ANT 12 • 16 mm • ANT 18 • 35 mm • ANT 30 • 55 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 140 years Interfaces Electrical connector design M12, 8-pin Antenna connector design M8, 4-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna External, antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30 Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 160 System Manual, 07/2017, C79000-G8976-C345-07 6GT2801-4AB10 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 100 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 75 x 75 x 41 mm Weight 250 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex approval
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 161 5.4.2.8 Approvals FCC information Siemens SIMATIC RF350R (MLFB 6GT2801-4AA10); FCC ID NXW-RF350R Siemens SIMATIC RF350R (MLFB 6GT2801-4AB10); FCC ID NXW-RF350R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 162 System Manual, 07/2017, C79000-G8976-C345-07 5.4.2.9 Dimension drawing Figure 5-17 RF350R dimension drawing Dimensions in mm
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 163 5.4.3 Use of the reader in hazardous areas TÜV NORD CERT GmbH as accredited test center and certification body, no. 0044 as per Article 9 of the Directive 94/9/EC of the European Council of 23 March 1994, has confirmed the compliance with the essential health and safety requirements relating to the design and construction of equipment and protective systems intended for use in hazardous areas as per Annex II of the Directive. The essential health and safety requirements are satisfied in accordance with the following standards: Document Title EN 60079-0: 2006 Electrical equipment for hazardous gas atmospheres - Part 0: General requirements EN 60079-15: 2005 Electrical equipment for hazardous gas atmospheres - Part 15: Design, testing and identification of electrical equipment with type of protection "n" IEC 61241 -0: 2006 Electrical apparatus for use in the presence of combustible dust - Part 0: General requirements IEC 61241 -1: 2004 Electrical apparatus for use in the presence of combustible dust - Part 1: Protection through enclosure WARNING EXPLOSION HAZARD DO NOT CONNECT OR DISCONNECT EQUIPMENT WHEN A FLAMMABLE OR COMBUSTIBLE ATMOSPHERE IS PRESENT. Identification The identification of the electrical equipment as an enclosed unit is: II 3 G Ex nA nC IIB T5 II 3 D Ex tD A22 IP6x T80 °C -25 °C to +70 °C Un = 20 to 30 VDC The equipment also has the following additional markings: XXXYYYZZZ [= serial number, is assigned during production] TÜV 10 ATEX 556039 [= certificate number]
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 164 System Manual, 07/2017, C79000-G8976-C345-07 5.4.3.1 Use of the readers in hazardous areas for gases Temperature class delineation for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 °C to +70 °C T5 WARNING Ignitions of gas-air mixtures When using the RF340R/RF350R readers, check to ensure that the temperature class is observed in respect of the requirements of the area of application. Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures. 5.4.3.2 Use of the readers in hazardous areas for dusts The equipment is suitable for dusts whose ignition temperatures for a dust layer of 5 mm are higher than 80 °C (smoldering temperature). With the ignition temperature according to type of protection iD specified here in compliance with IEC 61241-0 and IEC 61241-11, the smoldering temperature of the dust layer is referenced in this case. Temperature class delineation for dusts Ambient temperature range Temperature value -25 °C < Ta < +70 °C T80 °C WARNING Ignitions of dust-air mixtures When using the RF340R/RF350R readers, check to ensure that the temperature values are observed in respect of the requirements of the area of application. Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of dust-air mixtures.
Readers 5.4 SIMATIC RF340R/RF350R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 165 5.4.3.3 Installation and operating conditions for the hazardous area NOTICE Device may be damaged Note the following conditions when installing and operating the device in a hazardous zone to avoid damage: • Making and breaking of circuits is permitted only in a de-energized state. • The maximum surface temperature, corresponding to the marking, applies only for operation without a cover of dust. • The device may only be operated in such a way that adequate protection against UV light is ensured. • The device may not be operated in areas influenced by processes that generate high electrostatic charges. • The equipment must be installed so that it is mechanically protected. • The device sockets must be protected with a shrink-on tube. • The 8 pin connector must be grounded via its supply line. • The device may only be operated with accessories specified or supplied by the manufacturer. All the points above also apply to the accessories (cables and connectors) and to the antennas (exception: the housing of antenna 1 does not need to be installed with impact protection).
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 166 System Manual, 07/2017, C79000-G8976-C345-07 5.5 SIMATIC RF340R/RF350R - 2nd generation 5.5.1 SIMATIC RF340R - 2nd generation 5.5.1.1 Features SIMATIC RF340R Characteristics Design ① RS-422 interface ② LED operating display Area of application Identification tasks on assembly lines in harsh industrial environments 5.5.1.2 Ordering data Table 5- 17 Ordering data for RF340R Article number RF340R with RS-422 interface (3964R) 6GT2801-2BA10
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 167 5.5.1.3 Pin assignment of the RS-422 interface Table 5- 18 Pin assignment Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.5.1.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 19 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flickers or is lit permanently. The reader has received a "RESET" command. The reader is turned on, the antenna is turned off. • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 413)". 5.5.1.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 168 System Manual, 07/2017, C79000-G8976-C345-07 5.5.1.6 Metal-free area The RF340R can be flush-mounted in metal. Allow for a possible reduction in the field data. To avoid any influence on the field data, the distance "a" should be kept to. a ≥ 20 mm Figure 5-18 Metal-free area for RF340R 5.5.1.7 Minimum distance between RF340R readers RF340R side by side D ≥ 350 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-19 Minimum distance between RF340R readers
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 169 RF340R face-of-face D ≥ 500 mm Figure 5-20 Face-of-face distance between two RF340Rs 5.5.1.8 Technical specifications Table 5- 20 Technical specifications of the RF340R reader 6GT2801-2BA10 Product type designation SIMATIC RF340R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 140 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder (MDS D) ISO tran-sponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 260 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna integrated Mechanical specifications Enclosure
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 170 System Manual, 07/2017, C79000-G8976-C345-07 6GT2801-2BA10 • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 60 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 75 x 75 x 41 mm Weight 210 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA (IEC 61010), Ex approval
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 171 5.5.1.9 Approvals FCC information Siemens SIMATIC RF340R (MLFB 6GT2801-2BA10); FCC ID NXW-RF340R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 172 System Manual, 07/2017, C79000-G8976-C345-07 UL information (IEC 61010-1 / IEC 61010-2-201) This standard applies to equipment designed to be safe at least under the following conditions: ● a) indoor use; ● b) altitude up to 2 000 m; ● c) temperature -25 °C to 70 °C; ● d) maximum relative humidity 80 % for temperature up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C; ● e) TRANSIENT OVERVALTAGES up to the levels of OVERVALTAGE CATEGORY II, NOTE 1: These levels of transient overvoltage are typical for equipment supplied from the building wiring. ● f) using a "NEC Class 2" power supply is required ● g) the device is categorized as pollution degree 3/4 5.5.1.10 Dimension drawing Figure 5-21 Dimension drawing for RF340R Dimensions in mm
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 173 5.5.2 SIMATIC RF350R - 2nd generation 5.5.2.1 Features SIMATIC RF350R Characteristics Design ① Antenna connection ② RS-422 interface ③ LED operating display Area of application Identification tasks in assembly lines in harsh industrial environments; for external antennas (ANT 1, ANT 3, ANT 12, ANT 18, ANT 30) Note Reader requires external antennas Note that the RF350R reader is designed only for operation with external antennas and only works in conjunction with the antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30. 5.5.2.2 Ordering data Table 5- 21 Ordering data for RF350R Article number RF350R with RS-422 interface (3964R) 6GT2801-4BA10
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 174 System Manual, 07/2017, C79000-G8976-C345-07 5.5.2.3 Pin assignment of the RS-422 interface Table 5- 22 Pin assignment Pin Pin Device end 8-pin M12 Assignment 1 + 24 V 2 - Transmit 3 0 V 4 + Transmit 5 + Receive 6 - Receive 7 Unassigned 8 Earth (shield) 5.5.2.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 23 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flickers or is lit permanently. The reader has received a "RESET" command. The reader is turned on, the antenna is turned off. • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 413)". 5.5.2.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 175 5.5.2.6 Metal-free area The RF350R reader does not have an internal antenna. Operation is not affected by mounting on metal or flush-mounting in metal. For information about the metal-free area required by the external antennas, refer to the corresponding section of the chapter "Antennas (Page 221)". 5.5.2.7 Technical specifications Table 5- 24 Technical specifications of the RF350R reader 6GT2801-4BA10 Product type designation SIMATIC RF350R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range • ANT 1 • 140 mm • ANT 3 • 50 mm • ANT 12 • 16 mm • ANT 18 • 35 mm • ANT 30 • 55 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder (MDS D) ISO tran-sponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 260 years Interfaces Electrical connector design M12, 8-pin Antenna connector design M8, 4-pin Standard for interfaces for communication RS-422 (3964R protocol) Antenna External, antennas ANT 1, ANT 3, ANT 12, ANT 18 or ANT 30
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 176 System Manual, 07/2017, C79000-G8976-C345-07 6GT2801-4BA10 Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • TI-Grey Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 60 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP65 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 75 x 75 x 41 mm Weight 250 g Type of mounting 2 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum 1000 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA (IEC 61010), Ex approval
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 177 5.5.2.8 Approvals FCC information Siemens SIMATIC RF350R (MLFB 6GT2801-4BA10); FCC ID NXW-RF350R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 178 System Manual, 07/2017, C79000-G8976-C345-07 UL information (IEC 61010-1 / IEC 61010-2-201) This standard applies to equipment designed to be safe at least under the following conditions: ● a) indoor use; ● b) altitude up to 2 000 m; ● c) temperature -25 °C to 70 °C; ● d) maximum relative humidity 80 % for temperature up to 31 °C decreasing linearly to 50 % relative humidity at 40 °C; ● e) TRANSIENT OVERVALTAGES up to the levels of OVERVALTAGE CATEGORY II, NOTE 1: These levels of transient overvoltage are typical for equipment supplied from the building wiring. ● f) using a "NEC Class 2" power supply is required ● g) the device is categorized as pollution degree 3/4 5.5.2.9 Dimension drawing Figure 5-22 RF350R dimension drawing Dimensions in mm
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 179 5.5.3 Using the readers in a hazardous area WARNING Explosion hazard In a flammable or combustible environment, no cables may be connected to or disconnected from the device. ATEX The SIMATIC Ident products meet the requirements of explosion protection acc. to ATEX. The products meet the requirements of the standards: Document Title EN 60079-0 Hazardous areas Part 0: Equipment - General requirements EN 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" EN 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" You will find the current versions of the standards in the currently valid ATEX certificates. ATEX mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the Ex mark is applied. The identification of the electrical equipment as an enclosed unit is: II 3 G Ex ec IIB T4 Gc II 3 D Ex tc IIIC T80°C Dc -25 °C ... +70 °C Un = 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production] DEMKO 17 ATEX 1767 X [= certificate number]
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 180 System Manual, 07/2017, C79000-G8976-C345-07 IECEx The SIMATIC Ident products meet the requirements of explosion protection acc. to IECEx. The products meet the requirements of the standards: Document Title IEC 60079-0 Hazardous areas Part 0: Equipment - General requirements IEC 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" IEC 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" You will find the current versions of the standards in the currently valid IECEx certificates. IECEx mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the IECEx mark is applied. The identification of the electrical equipment as an enclosed unit is: II 3 G Ex ec IIB T4 Gc II 3 D Ex tc IIIC T80°C Dc -25 °C ... +70 °C Un= 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production] IECEx ULD 17.0031 X [= certificate number]
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 181 UL HAZ. LOC. The SIMATIC Ident products meet the requirements of explosion protection acc. to UL HAZ. LOC. The products meet the requirements of the standards: Document Title UL 60079-0 Hazardous areas Part 0: Equipment - General requirements CSA C22.2 NO. 60079-0 UL 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" CSA C22.2 NO. 60079-7 UL 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" CSA C22.2 NO. 60079-31 You will find the current versions of the standards in the currently valid UL HAZ. LOC. certificates UL HAZ. LOC. mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the UL HAZ. LOC. mark is applied. The identification of the electrical equipment as an enclosed unit is: E223122 IND.CONT.EQ FOR HAZ.LOC. CL.I, DIV.2, GP.C,D T4 CL.II, DIV.2, GP.F,G T80°C AEx ec IIB T4, Ex ec IIB T4 AEx tc IIIC T80°C, Ex tc IIIC T80°C -25 °C ... +70 °C Un= 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production]
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 182 System Manual, 07/2017, C79000-G8976-C345-07 5.5.3.1 Using the reader in hazardous area for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 ℃ ... +70 ℃ T4 WARNING Ignitions of gas-air mixtures When using the reader, check to make sure that the temperature class is adhered to in keeping with the requirements of the area of application Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures. 5.5.3.2 Using the reader in hazardous area for dust The equipment is suitable for dusts whose ignition temperatures for a dust layer of 5 mm are higher than 80 °C (smoldering temperature). Ambient temperature range Temperature value -25 °C < Ta < +70 °C T80 °C WARNING Ignitions of dust-air mixtures When using the reader, check to make sure that the temperature values are adhered to in keeping with the requirements of the area of application. Non-compliance with the permitted temperature range while using the reader can lead to ignitions of dust-air mixtures.
Readers 5.5 SIMATIC RF340R/RF350R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 183 5.5.3.3 Installation and operating conditions for hazardous areas: NOTICE Risk of explosion Risk of explosion of dust-air mixtures or gas-air mixtures and the device can be damaged. Note the following conditions when installing and operating the device in a hazardous area: • Making and breaking of circuits is permitted only in a de-energized state. • The maximum surface temperature, corresponding to the marking, applies only for operation without a cover of dust. • The device may only be operated in such a way that adequate protection against UV light is ensured. • The device may not be operated in areas influenced by processes that generate high electrostatic charges. • The device must be installed so that it is mechanically protected. • The grounding of the plug (8-pin) on the reader must be via its supply cable. • The device may only be operated with accessories specified or supplied by the manufacturer. All the points above also apply to the accessories (cables and connectors) and to the antennas (exception: the housing of ANT 1 does not need to be installed with impact protection). • The device sockets incl. the metal parts of the connecting cable must have a shrink-on sleeve pulled over them, in other words, all metal parts apart from the securing sockets of the housing must be fully covered and be inaccessible. • After disconnecting the connections (antenna cable, signal/supply cable), before the plugs are inserted again, they must be checked for contamination and if necessary cleaned.
Readers 5.6 SIMATIC RF380R SIMATIC RF300 184 System Manual, 07/2017, C79000-G8976-C345-07 5.6 SIMATIC RF380R 5.6.1 Features SIMATIC RF380R Characteristics Design ① RS-232 or RS-422 interface ② Status display Area of application Identification tasks on assembly lines in harsh industrial environments 5.6.2 RF380R ordering data Table 5- 25 RF380R ordering data Article number RF380R with RS-232/RS-422 interface (3964R) 6GT2801-3AB10 5.6.3 Pin assignment of RF380R RS-232/RS-422 interface You can connect the RF380R reader to a higher-level system via the internal RS-422 interface or via the RS-232 interface. After connection, the interface module automatically detects which interface has been used.
Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 185 Note correct assignment of the pins here: Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.6.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 26 LED operating display on the reader LED Meaning The reader is turned off. Operating voltage present, reader not initialized or antenna switched off Operating voltage present, reader initialized and antenna switched on • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the cur-rent error. You will find more information on error messages in the section "System diagnostics (Page 413)". 5.6.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Readers 5.6 SIMATIC RF380R SIMATIC RF300 186 System Manual, 07/2017, C79000-G8976-C345-07 5.6.6 Metal-free area The RF380R can be flush-mounted in metal. Allow for a possible reduction in the field data. Figure 5-23 Metal-free area for RF380R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.6.7 Minimum distance between RF380R readers RF380R side by side D ≥ 400 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-24 Minimum distance between RF380R readers
Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 187 RF380R face-to-face D ≥ 800 mm Figure 5-25 Face-to-face distance between two RF380R 5.6.8 Technical specifications Table 5- 27 Technical specifications of the RF380R reader 6GT2801-3AB10 Product type designation SIMATIC RF380R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 200 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read • approx. 8000 bytes/s • approx. 1500 bytes/s • Write • approx. 8000 bytes/s • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 109 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232/RS-422 (3964R protocol) Antenna integrated Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite
Readers 5.6 SIMATIC RF380R SIMATIC RF300 188 System Manual, 07/2017, C79000-G8976-C345-07 6GT2801-3AB10 Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 160 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 160 x 80 x 41 mm Weight 600 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio in accordance with R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex: II 3G Ex nC IIB T5
Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 189 5.6.9 Approvals FCC information Siemens SIMATIC RF380R (MLFB 6GT2801-3AA10); FCC ID NXW-RF380R Siemens SIMATIC RF380R (MLFB 6GT2801-3AB10); FCC ID NXW-RF380R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.
Readers 5.6 SIMATIC RF380R SIMATIC RF300 190 System Manual, 07/2017, C79000-G8976-C345-07 5.6.10 Dimension drawing Figure 5-26 Dimension drawing RF380R Dimensions in mm 5.6.11 Use of the reader in a hazardous 5.6.11.1 Use of the reader in a hazardous area The TÜV SÜD Automotive GmbH as approved test center as well as the TÜV SÜD Product Service GmbH as certification center, identification number 0123, as per Article 9 of the Directive of the European Council of 23 March 1994 (94/9/EC), has confirmed the compliance with the essential health and safety requirements relating to the design and construction of equipment and protective systems intended for use in hazardous areas as per Annex II of the Directive. The essential health and safety requirements are satisfied in accordance with the following standards: Document Title EN 60079-0: 2006 Electrical equipment for hazardous gas atmospheres - Part 0: General requirements EN 60079-15: 2005 Electrical equipment for hazardous gas atmospheres - Part 15: Design, testing and identification of electrical equipment with type of protection "n" DIN VDE 0848-5: 2001 (in parts) Safety in electrical, magnetic and electromagnetic fields - Part 5: Explosion protection ZLS SK 107.1 Central office of the states for safety; test components
Readers 5.6 SIMATIC RF380R SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 191 Identification The identification of the electrical equipment as an enclosed unit is: II 3G Ex nC IIB T5 -25°C to +70°C Um=30 V DC The equipment is assigned the following references: XXXYYYZZZ [= serial number, is assigned during production] TPS 09 ATEX 1 459 X [= certificate number] "No use of the equipment in the vicinity of processes generating high charges" "Do not disconnect plug on load" 5.6.11.2 Use of the reader in hazardous areas for gases Temperature class grading for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 °C to +70 °C T5 WARNING Ignitions of gas-air mixtures When using the RF380R reader, check to ensure that the temperature class is observed in respect of the requirements of the area of application Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures.
Readers 5.6 SIMATIC RF380R SIMATIC RF300 192 System Manual, 07/2017, C79000-G8976-C345-07 5.6.11.3 Installation and operating conditions for hazardous areas: NOTICE Explosion hazard Risk of explosion of gas-air mixtures and the device can be damaged. Note the following conditions when installing and operating the device in a hazardous area: • Making and breaking of circuits is permitted only in a de-energized state. • The maximum surface temperature, corresponding to the marking, applies only for operation without a cover of dust. • The device may only be operated in such a way that adequate protection against UV light is ensured. • The device may not be operated in areas influenced by processes that generate high electrostatic charges. • The device must be installed so that it is mechanically protected. • The grounding of the plug (8-pin) on the reader must be via its supply cable. • The device may only be operated with accessories specified or supplied by the manufacturer. All the points above also apply to the accessories (cables and connectors) and to the antennas (exception: the housing of ANT 1 does not need to be installed with impact protection). • The device sockets incl. the metal parts of the connecting cable must have a shrink-on sleeve pulled over them, in other words, all metal parts apart from the securing sockets of the housing must be fully covered and be inaccessible. • After disconnecting the connections (antenna cable, signal/supply cable), before the plugs are inserted again, they must be checked for contamination and if necessary cleaned.
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 193 5.7 SIMATIC RF380R with Scanmode You will find detailed information on the SIMATIC RF382R with Scanmode on the Industry Online Support - SIMATIC RF380R with Scanmode (https://support.industry.siemens.com/cs/ww/en/ps/15037). 5.7.1 Features RF380R Scanmode Characteristics Design ① RS-232 or RS-422 interface ② Status display Area of application Identification tasks on assembly lines in harsh industrial environments 5.7.2 Ordering data for RF380R with Scanmode Table 5- 28 Ordering data RF380R Scanmode Product Article number RF380R Scanmode 6GT2801-3AB20-0AX1
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 194 System Manual, 07/2017, C79000-G8976-C345-07 5.7.3 Pin assignment RF380R Scanmode RS-232 interface You can connect the RF380R Scanmode reader via the internal RS-232/RS-422 interface to a higher-level system. (See section "Basic rules (Page 111)") Make sure that the pin assignment is correct. In the factory settings, the reader is set to RS-232. Siemens can change the interface to RS-422. Table 5- 29 Connector and reader pin assignment Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.7.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 30 LED operating display on the reader LED Meaning The reader is turned off. Operating voltage present, reader ready for operation • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diagnostics (Page 413)". 5.7.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 195 5.7.6 Metal-free area The RF380R can be flush-mounted in metal. Allow for a possible reduction in the field data. Figure 5-27 Metal-free area for RF380R To avoid any impact on the field data, the distance a should be ≥ 20 mm. 5.7.7 Minimum distance between several RF380R Scanmode readers RF380R side by side D ≥ 400 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-28 Minimum distance between RF380R readers
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 196 System Manual, 07/2017, C79000-G8976-C345-07 RF380R face-to-face D ≥ 800 mm Figure 5-29 Face-to-face distance between two RF380R 5.7.8 Technical specifications Table 5- 31 Technical specifications of the RF380R Scanmode reader 6GT2801-3AB20-0AX1 Product type designation SIMATIC RF380R Scanmode Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 200 mm Maximum data transmission speed reader ↔ transponder RF300 transponder ISO transponder • Read approx. 8000 bytes/s approx. 1500 bytes/s Transmission speed 9.6, 19.2, 38.4, 57, 115.2 kBd Read distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 109 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232 / RS-422 Antenna integrated Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 197 6GT2801-3AB20-0AX1 Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 160 mA Permitted ambient conditions Ambient temperature • During operation -25 to +70 °C • During transportation and storage -40 to +85 °C Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 160 x 80 x 41 (without M12 device connector) Weight Approx. 600 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA 5.7.9 Approvals FCC information Siemens SIMATIC RF380R (MLFB 6GT2801-3AB20-0AX1); FCC ID NXW-RF380R01 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 198 System Manual, 07/2017, C79000-G8976-C345-07 Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. 5.7.10 Certificates and Approvals Certificates for USA and Canada Underwriters Laboratories (UL) acc. to standard UL 60950, Report E11 5352 and Ca-nadian standard C22.2 No. 60950 (I.T.E) or acc. to UL508 and C22.2 No. 142 (IND.CONT.EQ)
Readers 5.7 SIMATIC RF380R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 199 5.7.11 Dimension drawing Figure 5-30 Dimension drawing RF380R Dimensions in mm
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 200 System Manual, 07/2017, C79000-G8976-C345-07 5.8 SIMATIC RF380R - 2nd generation 5.8.1 Features SIMATIC RF380R Characteristics Design ① RS-232 or RS-422 interface ② Status display Area of application Identification tasks on assembly lines in harsh industrial environments 5.8.2 RF380R ordering data Table 5- 32 RF380R ordering data Article number RF380R with RS-232/RS-422 interface (3964R) 6GT2801-3BA10
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 201 5.8.3 Pin assignment of RF380R RS-232/RS-422 interface You can connect the RF380R reader to a higher-level system via the internal RS-422 interface or via the RS-232 interface. After connection, the interface module automatically detects which interface has been used. Note correct assignment of the pins here: Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.8.4 LED operating display The operational statuses of the reader are displayed by two LEDs. The LEDs can adopt the colors white green, red, yellow or blue and the statuses off , on , flashing : Table 5- 33 Display elements LED Meaning The reader is turned off. The reader is turned on and is searching for transponders. The reader is in the "Setup" mode, in the "Search for transponders" status and has not yet received a "RESET" command and is not ready. / There is transponder in the antenna field. The reader is in the "Setup" mode, in the status "Show quality", has not yet re-ceived a "RESET" command and is not ready. Depending on the signal strength, the LED flickers or is lit permanently. The reader has received a "RESET" command. The reader is turned on, the antenna is turned off. • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diag-nostics (Page 413)".
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 202 System Manual, 07/2017, C79000-G8976-C345-07 5.8.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window. 5.8.6 Metal-free area Figure 5-31 Metal-free space for RF380R - 2nd generation The RF380R can be flush-mounted in metal. Allow for a possible reduction in the field data. To avoid any impact on the field data, the distance a should be ≥ 20 mm.
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 203 5.8.7 Minimum distance between RF380R readers RF380R side by side D ≥ 400 mm (with 2 readers) D ≥ 500 mm (with more than 2 readers) Figure 5-32 Minimum distance between multiple RF380R - 2nd generation RF380R face-to-face D ≥ 800 mm Figure 5-33 Face-of-face distance between two RF380R - 2nd generation
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 204 System Manual, 07/2017, C79000-G8976-C345-07 5.8.8 Technical specifications Table 5- 34 Technical specifications of the RF380R reader 6GT2801-3BA10 Product type designation SIMATIC RF380R Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 240 mm Maximum data transmission speed reader ↔ transponder RF300 tran-sponder ISO tran-sponder (MDS D) ISO transponder (MDS E) • Read • ≤ 8000 bytes/s • ≤ 3300 bytes/s • ≤ 3400 bytes/s • Write • ≤ 8000 bytes/s • ≤ 1700 bytes/s • ≤ 800 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 172.6 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232/RS-422 (3964R protocol) Antenna integrated Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 130 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 205 6GT2801-3BA10 • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 160 x 80 x 41 mm Weight 600 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 2 LEDs, 5 colors Standards, specifications, approvals Proof of suitability Radio in accordance with R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA, Ex: II 3G Ex nC IIB T4 5.8.9 Approvals FCC information Siemens SIMATIC RF380R (MLFB 6GT2801-3BA10); FCC ID NXW-RF380R02 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 206 System Manual, 07/2017, C79000-G8976-C345-07 Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense. IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement.
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 207 5.8.10 Dimension drawing Figure 5-34 Dimension drawing SIMATIC RF380R - 2nd generation Dimensions in mm 5.8.11 Using the reader in hazardous area WARNING Explosion hazard In a flammable or combustible environment, no cables may be connected to or disconnected from the device.
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 208 System Manual, 07/2017, C79000-G8976-C345-07 ATEX The SIMATIC Ident products meet the requirements of explosion protection acc. to ATEX. The products meet the requirements of the standards: Document Title EN 60079-0 Hazardous areas Part 0: Equipment - General requirements EN 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" EN 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" You will find the current versions of the standards in the currently valid ATEX certificates. ATEX mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the Ex mark is applied. The identification of the electrical equipment as an enclosed unit is: II 3 G Ex ec IIB T4 Gc II 3 D Ex tc IIIC T80°C Dc -25 °C ... +70 °C Un = 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production] DEMKO 17 ATEX 1767 X [= certificate number]
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 209 IECEx The SIMATIC Ident products meet the requirements of explosion protection acc. to IECEx. The products meet the requirements of the standards: Document Title IEC 60079-0 Hazardous areas Part 0: Equipment - General requirements IEC 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" IEC 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" You will find the current versions of the standards in the currently valid IECEx certificates. IECEx mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the IECEx mark is applied. The identification of the electrical equipment as an enclosed unit is: II 3 G Ex ec IIB T4 Gc II 3 D Ex tc IIIC T80°C Dc -25 °C ... +70 °C Un= 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production] IECEx ULD 17.0031 X [= certificate number] UL HAZ. LOC. The SIMATIC Ident products meet the requirements of explosion protection acc. to UL HAZ. LOC. The products meet the requirements of the standards: Document Title UL 60079-0 Hazardous areas Part 0: Equipment - General requirements CSA C22.2 NO. 60079-0 UL 60079-7 Hazardous areas Part 7: Equipment protection by increased safety "e" CSA C22.2 NO. 60079-7 UL 60079-31 Potentially explosive atmosphere Part 31: Equipment dust ignition protection by enclosure "t" CSA C22.2 NO. 60079-31
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 210 System Manual, 07/2017, C79000-G8976-C345-07 You will find the current versions of the standards in the currently valid UL HAZ. LOC. certificates UL HAZ. LOC. mark NOTICE Validity only when the devices are marked There is a corresponding approval only with devices to which the UL HAZ. LOC. mark is applied. The identification of the electrical equipment as an enclosed unit is: E223122 IND.CONT.EQ FOR HAZ.LOC. CL.I, DIV.2, GP.C,D T4 CL.II, DIV.2, GP.F,G T80°C AEx ec IIB T4, Ex ec IIB T4 AEx tc IIIC T80°C, Ex tc IIIC T80°C -25 °C ... +70 °C Un= 24 VDC The equipment also has the following additional information: XXXYYYZZZ [= serial number, is assigned during production] 5.8.11.1 Using the reader in hazardous area for gases The temperature class of the reader for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 ℃ ... +70 ℃ T4 WARNING Ignitions of gas-air mixtures When using the reader, check to make sure that the temperature class is adhered to in keeping with the requirements of the area of application Non-compliance with the permitted temperature ranges while using the reader can lead to ignitions of gas-air mixtures.
Readers 5.8 SIMATIC RF380R - 2nd generation SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 211 5.8.11.2 Using the reader in hazardous area for dust The equipment is suitable for dusts whose ignition temperatures for a dust layer of 5 mm are higher than 80 °C (smoldering temperature). Ambient temperature range Temperature value -25 °C < Ta < +70 °C T80 °C WARNING Ignitions of dust-air mixtures When using the reader, check to make sure that the temperature values are adhered to in keeping with the requirements of the area of application. Non-compliance with the permitted temperature range while using the reader can lead to ignitions of dust-air mixtures. 5.8.11.3 Installation and operating conditions for hazardous areas: NOTICE Risk of explosion Risk of explosion of dust-air mixtures or gas-air mixtures and the device can be damaged. Note the following conditions when installing and operating the device in a hazardous area: • Making and breaking of circuits is permitted only in a de-energized state. • The maximum surface temperature, corresponding to the marking, applies only for operation without a cover of dust. • The device may only be operated in such a way that adequate protection against UV light is ensured. • The device may not be operated in areas influenced by processes that generate high electrostatic charges. • The device must be installed so that it is mechanically protected. • The grounding of the plug (8-pin) on the reader must be via its supply cable. • The device may only be operated with accessories specified or supplied by the manufacturer. All the points above also apply to the accessories (cables and connectors) and to the antennas (exception: the housing of ANT 1 does not need to be installed with impact protection). • The device sockets incl. the metal parts of the connecting cable must have a shrink-on sleeve pulled over them, in other words, all metal parts apart from the securing sockets of the housing must be fully covered and be inaccessible. • After disconnecting the connections (antenna cable, signal/supply cable), before the plugs are inserted again, they must be checked for contamination and if necessary cleaned.
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 212 System Manual, 07/2017, C79000-G8976-C345-07 5.9 SIMATIC RF382R with Scanmode You will find detailed information on the SIMATIC RF382R with Scanmode on the Internet (https://support.industry.siemens.com/cs/ww/en/ps/15038). 5.9.1 Characteristics RF382R Scanmode Characteristics Design ① RS-232 or RS-422 interface ② Status display Operating range Suitable for high speeds, e.g. in • Suspension conveyor systems • Assembly lines • Production • Order picking 5.9.2 RF382R with Scanmode ordering data Table 5- 35 RF382R Scanmode ordering data Article number RF382R Scanmode 6GT2801-3AB20-0AX0
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 213 5.9.3 Pin assignment RF382R Scanmode RS232 interface You can connect the RF382R Scanmode reader via the internal RS-232/RS-422 interface or via a higher-level system. (See section "Basic rules (Page 111)") Make sure that the pin assignment is correct. In the factory settings, the reader is set to RS-232. Siemens can change the interface to RS-422. Table 5- 36 Connector and reader pin assignment Pin Pin Device end 8-pin M12 Assignment RS-232 RS-422 1 + 24 V + 24 V 2 RXD - Transmit 3 0 V 0 V 4 TXD + Transmit 5 not used + Receive 6 not used - Receive 7 not used not used 8 Ground (shield) Ground (shield) 5.9.4 LED operating display The operational statuses of the reader are displayed by the LEDs. The LED can adopt the colors green, red or yellow and the statuses off , on , flashing : Table 5- 37 LED operating display on the reader LED Meaning The reader is turned off. Operating voltage present, reader ready for operation • Operating mode "with presence": Transponder present • Operating mode "without presence": Transponder present and command currently being executed There is an error. The number of flashes provides information about the current error. You will find more information on error messages in the section "System diagnostics (Page 413)". 5.9.5 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 214 System Manual, 07/2017, C79000-G8976-C345-07 5.9.6 Mounting on metal The RF382R can be mounted directly on metal. Flush mounting on metal is not permitted. 5.9.7 Minimum distance between several RF382R Scanmode readers Figure 5-35 Minimum distance between several RF382R Scanmode readers Minimum distance D from RF382R to RF382R D ≥ 200 mm 5.9.8 Transmission window Orientation of fields of the SIMATIC RF382R Scanmode For many applications it may be best to operate the reader so that the tags move from left to right (or from right to left) at a certain distance in front of the narrow edge of the reader. With this direction of movement, the horizontal reader field is used, see figure below. You also have the option of moving the tags up and down (or down and up) past the narrow edge of the reader. With this direction of movement, uses the vertical reader field is used.
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 215 Figure 5-36 Definition of horizontal and vertical reader field Maximum field strength The reader creates the maximum field approximately 13 mm below the upper reader edge. For the largest possible reading range the tags you want to read should move in this range. This applies regardless of whether the horizontal or the vertical field is used. Figure 5-37 Line of maximum magnetic field strength The area of the maximum field strength and, therefore, the maximum range is identified by a laser icon: Figure 5-38 Laser labeling
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 216 System Manual, 07/2017, C79000-G8976-C345-07 Transmission window horizontal field Figure 5-39 Distance definition horizontal field Green Main field (processing field) Blue Secondary fields, horizontal field Lx Maximum length of the main field, horizontal field d Distance from the reader edge at which maximum horizontal main field length L exists Sa Operating range in the main field Sg Limit distance ① Level 1 ② Level 2 ③ Level 3 ⇒ Direction of motion of the transponder Operating range (Sa) The operating range lies between Level ① and Level ③. The operating range between Levels ① and ② includes secondary fields. The recommended operating range therefore lies in the green main field between Level 2 and Level 3.
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 217 Limit distance (Sg) The limit distance lies on Level ③. Transmission window vertical field Figure 5-40 Distance definition vertical field Green Main field (processing field) Ly Maximum length of the main field, vertical field d Distance from the reader edge at which maximum vertical main field length Ly exists Sa Operating range in the main field Sg Limit distance Dopt = 13 mm ⇓ Direction of motion of the transponder
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 218 System Manual, 07/2017, C79000-G8976-C345-07 5.9.9 Technical specifications Table 5- 38 Technical specifications of the RF382R reader with Scanmode 6GT2801-3AB20-0AX0 Product type designation SIMATIC RF382R Scanmode Radio frequencies Operating frequency, rated value 13.56 MHz Electrical data Maximum range 75 mm Maximum data transmission speed reader ↔ transponder ISO transponder • Read • approx. 1500 bytes/s Transmission speed 19.2, 57.6, 115.2 kBd Read/write distances of the reader See section "Field data for transponders, readers and antennas (Page 51)." MTBF (Mean Time Between Failures) 115 years Interfaces Electrical connector design M12, 8-pin Standard for interfaces for communication RS-232 (factory setting, can be changed to RS-422) Antenna integrated Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal 0 mm Supply voltage, current consumption, power loss Supply voltage 24 VDC Typical current consumption 140 mA Permitted ambient conditions Ambient temperature • During operation • -25 to +70 ℃ • During transportation and storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 219 6GT2801-3AB20-0AX0 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 160 x 80 x 41 mm Weight 550 g Type of mounting 4 x M5 screws; 1.5 Nm Cable length for RS-422 interface, maximum RS-422 RS-232 1000 m 30 m LED display design 3-color LED Standards, specifications, approvals Proof of suitability Radio to R&TTE directives EN 300330, EN 301489, CE, FCC, UL/CSA 5.9.10 Approvals FCC information Siemens SIMATIC RF382R (MLFB 6GT2801-3AB20-0AX0); FCC ID NXW-RF382R This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
Readers 5.9 SIMATIC RF382R with Scanmode SIMATIC RF300 220 System Manual, 07/2017, C79000-G8976-C345-07 IC information This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d`Industrie Canada applicables aux appareils radio exempts de licence. L`exploitation est autorisée aux deux conditions suivantes : (1) L`appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l`appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d`en compromettre le fonctionnement. Certificates for USA and Canada Underwriters Laboratories (UL) acc. to standard UL 60950, Report E11 5352 and Ca-nadian standard C22.2 No. 60950 (I.T.E) or acc. to UL508 and C22.2 No. 142 (IND.CONT.EQ) 5.9.11 Dimensional diagram Figure 5-41 Dimension drawing
SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 221 Antennas 6 6.1 Features For the RF350R and RF350M readers, you can use the following plug-in antennas: Antenna Product photo Limit distance Sg 1) Dimensions ANT 1 Up to 140 mm 75 x 75 x 20 mm (L x W x H) ANT 3 Up to 50 mm 50 x 75 x 10 mm (L x W x H)
Antennas 6.1 Features SIMATIC RF300 222 System Manual, 07/2017, C79000-G8976-C345-07 Antenna Product photo Limit distance Sg 1) Dimensions ANT 3S Up to 5 mm 50 × 28 × 10 mm (L x W x H) ANT 8 2) Up to 4 mm M8 x 1.0 x 39 mm (∅ x thread x L) ANT 12 Up to 16 mm M12 x 1.0 x 40 mm (∅ x thread x L) ANT 18 Up to 35 mm M18 x 1.0 x 55 mm (Ø x thread x L) ANT 30 Up to 55 mm M30 x 1.5 x 61 mm (Ø x thread x L) 1) Depending on the transponder used 2) only released with RF350M und RF350R - second generation
Antennas 6.1 Features SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 223 Note Use of the antennas in hazardous areas The antennas ANT 1, ANT 12, ANT 18 and ANT 30 are approved for use in hazardous locations. For more information, refer to the section "Use of the reader in hazardous areas (Page 163)". ANT 1 The ANT 1 is an antenna in the mid performance range and can be used to the customer's advantage in production and assembly lines due to its manageable housing shape. The antenna dimensions make it possible to read/write large quantities of data dynamically from/to the transponder during operation. The antenna cable can be plugged in. ANT 3 The ANT 3 is designed for use in small assembly lines. The extremely compact design of the antenna allows extremely accurate positioning. The antenna cable can be plugged in. ANT 3S Due to its slimline and compact design, the ANT 3S can still be precisely positioned in cramped conditions. Areas of application are, for example, tool identification. The antenna cable can be plugged in. ANT 8 The ANT 8 is primarily envisaged for tool identification applications. The extremely small design of the antenna allows extremely accurate positioning. The antenna cable can be connected at the reader end and screwed to the antenna. The antenna ANT 8 has currently only been tested and released for use in conjunction with the mobile reader RF350M and the reader RF350R - second generation. ANT 12 The ANT 12 is primarily envisaged for tool identification applications. The very small size of the antenna means that highly exact positioning is possible using the plastic nuts included in the scope of delivery. The antenna cable can be plugged in. ANT 18 The ANT 18 is designed for use in small assembly lines. Due to its small, compact construction, the antenna can be easily positioned for any application using two plastic nuts (included in the package). The antenna cable can be connected at the reader end.
Antennas 6.2 Ordering data SIMATIC RF300 224 System Manual, 07/2017, C79000-G8976-C345-07 ANT 30 The ANT 30 is designed for use in small assembly lines. In comparison to ANT 18, the maximum write/read distance is approximately 60 % larger. Due to its compact construction, the antenna can be easily positioned for any application using two plastic nuts (included in the package). The antenna cable can be connected at the reader end. 6.2 Ordering data Table 6- 1 Ordering data for antennas Article number ANT 1 incl. integrated antenna cable 3 m 6GT2398-1CB00 ANT 3 without antenna connecting cable 6GT2398-1CD30-0AX0 incl. plug-in antenna cable 3 m 6GT2398-1CD40-0AX0 ANT 3S without antenna connecting cable 6GT2398-1CD50-0AX0 incl. plug-in antenna cable 3 m 6GT2398-1CD60-0AX0 ANT 8 without antenna connecting cable 6GT2398-1CF00 incl. plug-in antenna cable 3 m 6GT2398-1CF10 ANT 12 incl. plug-in antenna cable 3 m 6GT2398-1CC00 ANT 18 incl. plug-in antenna cable 3 m 6GT2398-1CA00 ANT 30 incl. plug-in antenna cable 3 m 6GT2398-1CD00 Table 6- 2 Antenna accessories ordering data Article number Antenna connecting cable 3 m 6GT2398-0AH30 6.3 Ensuring reliable data exchange The "center point" of the transponder must be situated within the transmission window.
Antennas 6.4 Metal-free area SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 225 6.4 Metal-free area The antennas ANT 1, ANT 8, ANT 12, ANT 18 and ANT 30 can be flush-mounted in metal. Please allow for a possible reduction in the field data values. During installation, maintain the minimum distances (a and b) on/flush with the metal. Note Reduction of range if the metal-free space is not maintained At values lower than a and b, the field data changes significantly, resulting in a reduction in the limit distance and operating distance. Therefore, during installation, maintain the minimum distances (a and b) on/flush with the metal. Metal-free space for flush-mounted installation of ANT 1 a = 40 mm Figure 6-1 ANT 1 flush-mounted in metal
Antennas 6.4 Metal-free area SIMATIC RF300 226 System Manual, 07/2017, C79000-G8976-C345-07 Metal-free space for flush-mounted installation of ANT 3 and ANT 3S ① ANT 3 ② Metal a = 10 mm Figure 6-2 ANT 3 and ANT 3S flush-mounted in metal Flush-mounting of ANT 8 Figure 6-3 ANT 8 flush-mounted in metal The ANT 8 can be flush-mounted in metal. Flush-mounting of ANT 12 Figure 6-4 ANT 12 flush-mounted in metal The ANT 12 can be flush-mounted in metal.
Antennas 6.4 Metal-free area SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 227 Metal-free space for flush-mounted installation of ANT 18 a = 10 mm b = 10 mm Figure 6-5 ANT 18 flush-mounted in metal Metal-free space for flush-mounted installation of ANT 30 a = 20 mm b = 20 mm Figure 6-6 ANT 30 flush-mounted in metal
Antennas 6.5 Minimum distance between antennas SIMATIC RF300 228 System Manual, 07/2017, C79000-G8976-C345-07 6.5 Minimum distance between antennas Table 6- 3 Minimum distance between antennas Diagram (example) Minimum distance [mm] Antennas next to each other ANT 1 D ≥ 300 mm ANT 3 D ≥ 150 mm ANT 3S D ≥ 20 mm ANT 8 D ≥ 50 mm ANT 12 D ≥ 70 mm ANT 18 D ≥ 100 mm ANT 30 D ≥ 100 mm Antennas face to face ANT 1 D ≥ 500 mm ANT 3 D ≥ 200 mm ANT 3S D ≥ 50 mm ANT 8 D ≥ 50 mm ANT 12 D ≥ 100 mm ANT 18 D ≥ 100 mm ANT 30 D ≥ 200 mm The reader electronics can be mounted directly alongside each other.
Antennas 6.6 Technical specifications SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 229 6.6 Technical specifications Table 6- 4 Technical specifications of the antennas ANT 1, ANT 3 , ANT 3S and ANT 8 ANT 1 ANT 3 ANT 3S ANT 8 Max. write/read distance antenna ↔ transponder (Sg) 140 mm 50 mm 5 mm 4 mm Housing dimensions 75 x 75 x 20 mm (L x W x H) 50 x 28 x 10 mm (L x W x H) 50 x 28 x 10 mm (L x W x H) M8 x 1.0 x 39 mm (Ø x thread x L) Color Anthracite Black Black silver-metallic Material Plastic PA 12 Plastic PA6-V0 Plastic PA6-V0 Stainless steel Plug connection M8, 4-pin; (pins on antenna side) M8, 4-pin; socket on antenna side M8, 4-pin; socket on antenna side M8, 4-pin; (pins on antenna side) Degree of protection to EN 60529 IP67 IP67 (front) Shock-resistant acc. to EN 60721-3-7, Class 7M21) Vibration-resistant to EN 60721-3-7, Class 7M21) 500 m/s2 200 m/s2 (3...50 Hz) Attachment of the antenna 2 x M5 screws 2 x M4 screws 2 x M4 screws 2x stainless steel nuts M8 x 1.0 mm Ambient temperature • During operation • During transportation and storage • -25 ℃ ... +70 ℃ • -40 °C ... +85 °C Approx. weight • without antenna cable • with antenna cable (3.0 m) • -- • 225 g • 35 g • 160 g • 35 g • 160 g • 10 g • 140 g 1) Warning: The values for shock and vibration are maximum values and must not be applied continuously. Table 6- 5 Technical specifications of the antennas ANT 12, ANT 18 and ANT 30 ANT 12 ANT 18 ANT 30 Max. write/read distance antenna ↔ transponder (Sg) 16 mm 35 mm 55 mm Housing dimensions M12 x 1.0 x 40 mm (Ø x thread x L) M18 x 1.0 x 55 mm (Ø x thread x L) M30 x 1.5 x 61 mm (Ø x thread x L) Color Pale turquoise Material Plastic Crastin Plug connection M8, 4-pin; (pins on antenna side)
Antennas 6.7 Dimensional drawings SIMATIC RF300 230 System Manual, 07/2017, C79000-G8976-C345-07 ANT 12 ANT 18 ANT 30 Degree of protection to EN 60529 IP67 (front) Shock-resistant acc. to EN 60721-3-7, Class 7M21) Vibration-resistant to EN 60721-3-7, Class 7M21) 500 m/s2 200 m/s2 (3...50 Hz) Attachment of the antenna 2 plastic nuts M12 x 1.0 mm 2 plastic nuts M18 x 1.0 mm 2 plastic nuts M30 x 1.5 mm Ambient temperature • During operation • During transportation and storage • -25 ℃ ... +70 ℃ • -40 °C ... +85 °C Approx. weight • without antenna cable • with antenna cable (3.0 m) • -- • 145 g • -- • 130 g • -- • 180 g 1) Warning: The values for shock and vibration are maximum values and must not be applied continuously. 6.7 Dimensional drawings The cable length is 3 m. All dimensions are in mm. ANT 1 Figure 6-7 Dimension drawing for ANT 1
Antennas 6.7 Dimensional drawings SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 231 ANT 3 / ANT 3S Figure 6-8 Dimension drawing ANT 3 7 ANT 3S ANT 8 Figure 6-9 Dimension drawing for ANT 8 ANT 12 Figure 6-10 Dimension drawing for ANT 12
Antennas 6.7 Dimensional drawings SIMATIC RF300 232 System Manual, 07/2017, C79000-G8976-C345-07 ANT 18 Figure 6-11 Dimension drawing for ANT 18 ANT 30 Figure 6-12 Dimension drawing for ANT 30
SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 233 RF300 transponder 7 Features of the RF300 transponders The RF300 transponders (RF3xxT) stand out particularly for their extremely fast data exchange with the RF300 readers (RF3xxR). With the exception of the RF320T transponder, all of the RF300 transponders have 8 to 64 KB of FRAM memory, which has an almost unlimited capacity for reading and writing.
RF300 transponder 7.1 Memory configuration of the RF300 transponders SIMATIC RF300 234 System Manual, 07/2017, C79000-G8976-C345-07 7.1 Memory configuration of the RF300 transponders 1) Physically identical memory When the OTP area is used, the corresponding user area (FF00-FF13) can no longer be modified (read only). Figure 7-1 Memory configuration of the RF300 transponders
RF300 transponder 7.1 Memory configuration of the RF300 transponders SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 235 EEPROM area The memory configuration of an RF300 transponder always comprises an EEPROM that has 20 bytes for user data (read/write) and a 4-byte unique serial number (UID, read only). For reasons of standardization, the UID is transferred as an 8 byte value through a read command to address FFF0 with a length of 8. The unused 4 high bytes are filled with zeros. Note Write speed The EEPROM user memory (address FF00-FF13, or FF80-FF90) requires significantly more time for writing (approx. 11 ms/byte) than the high-speed FRAM memory. For time-critical applications with write functions, it is advisable to use FRAM transponders (e.g. RF330T, RF340T, RF350T, RF360T, RF370T, RF380T). FRAM area Depending on the tag type, high-speed FRAM memory is available. (8 KB, 32 KB, 64 KB). This area does not exist for the RF320T. In the case of RF3xxT transponders with FRAM memory, the data carrier initialization command (INIT) is only effective on this memory area but not on the EEPROM area (FF00-FF13). OTP area The EEPROM memory area (address FF00-FF13) can also be used as a so-called "OTP" memory (One Time Programmable). The 5 block addresses FF80, FF84, FF88, FF8C and FF90 are used for this purpose. A write command to this block address with a valid length (4, 8, 12, 16, 20 depending on the block address) protects the written data from subsequent overwriting. Note Seamless use of the OTP area When the OTP area is used, it must be ensured that the blocks are used starting from Block 0 consecutively. Examples: • 3 blocks (with write command), Block 0, 1, 2 (FF80, length = 12): valid • 2 blocks (consecutive), Block 0 (FF80, length =4), Block 1 (FF84, length = 4): valid • 2 blocks (consecutive), Block 0 (FF80, length =4), Block 2 (FF88, length = 4): Invalid • 1 Block, Block 4 (FF90, length = 4): Invalid
RF300 transponder 7.2 SIMATIC RF320T SIMATIC RF300 236 System Manual, 07/2017, C79000-G8976-C345-07 Note Use of the OTP area is not reversible If you use the OPT area, you cannot undo it, because the OPT area can only be written to once. 7.2 SIMATIC RF320T 7.2.1 Features RF320T Characteristics Area of application Identification tasks on small assembly lines in harsh industrial environments Memory size 20 bytes of EEPROM user memory Write/read range See section Field data of RF300 transponders (Page 52) Mounting on metal Yes, with spacer Degree of protection IP67/IPx9K 7.2.2 Ordering data Table 7- 1 Ordering data RF320T Article number RF320T 6GT2800-1CA00 Table 7- 2 Ordering data for RF320T accessories Article number Spacer 6GT2690-0AK00
RF300 transponder 7.2 SIMATIC RF320T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 237 7.2.3 Mounting on metal Mounting on metal h ≥ 15 mm Figure 7-2 Mounting the MDS D124/D324/D424/D524/E624 and RF320T on metal with spacer Flush-mounting h ≥ 15 mm a ≥ 25 mm Figure 7-3 Flush-mounting of the MDS D124/D324/D424/D524/E624 and RF320T in metal with spacer
RF300 transponder 7.2 SIMATIC RF320T SIMATIC RF300 238 System Manual, 07/2017, C79000-G8976-C345-07 Note Going below the distances If the distances (a and h) are not observed, a reduction of the field data results. It is possible to mount the MDS with metal screws (M3 countersunk head screws). This has no tangible impact on the range. 7.2.4 Technical data Table 7- 3 Technical specifications for RF320T 6GT2800-1CA00 Product type designation SIMATIC RF320T Memory Memory organization Byte-oriented, write protection possible in 4-byte blocks Memory configuration • UID • 4 bytes EEPROM • User memory • 20 bytes EEPROM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 105 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1800 years Mechanical specifications Enclosure • Material • Epoxy resin • Color • Black Recommended distance to metal ≥ 20 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +125 ℃ • outside the read/write field • -40 ... +140 °C
RF300 transponder 7.2 SIMATIC RF320T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 239 6GT2800-1CA00 • during storage • -40 to +140 ℃ Degree of protection to EN 60529 • IP67 • IPx9K Shock-resistant acc. toEN 60721-3-7, Class 7 M31) 1000 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (Ø x H) 27 x 4 mm Weight 5 g Type of mounting • 1 x M3 screw 2) ≤ 1.0 Nm • Glued 3) 1) The values for shock and vibration are maximum values and must not be applied continuously. 2 ) To prevent it loosening during operation, secure the screw with screw locking varnish. 3) The glue manufacturer's processing instructions must be observed. 7.2.5 Dimension drawing Figure 7-4 RF320T dimension drawing Dimensions in mm
RF300 transponder 7.3 SIMATIC RF330T SIMATIC RF300 240 System Manual, 07/2017, C79000-G8976-C345-07 7.3 SIMATIC RF330T 7.3.1 Features Table 7- 4 RF330T Characteristics Area of application In production automation for identification of metallic workpiece holders, workpieces or containers. Memory size 32 KB EEPROM user memory Write/read range See section "Field data of RF300 transpond-ers (Page 52)" Mounting on metal Yes flush mounted on/in metal Degree of protection IP68/IPx9K 7.3.2 Ordering data Table 7- 5 Ordering data RF330T Article number RF330T 6GT2800-5BA00 Table 7- 6 Ordering data for RF330T accessories Article number Fixing hood RF330T / MDS D423 6GT2690-0AE00 7.3.3 Mounting on/in metal Direct mounting of the RF330T on metal is permitted.
RF300 transponder 7.3 SIMATIC RF330T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 241 Mounting of the RF330T on metal Figure 7-5 Mounting of the RF330T on metal Flush-mounting of RF330T in metal a ≥ 10 mm Figure 7-6 Mounting of the RF330T in metal with 10 mm clearance Figure 7-7 Mounting of the RF330T in metal without clearance
RF300 transponder 7.3 SIMATIC RF330T SIMATIC RF300 242 System Manual, 07/2017, C79000-G8976-C345-07 Note Reduction of the write/read range Note that when the device is flush-mounted in metal without a surrounding clearance ≥ 10 mm, the write/read range is significantly reduced. 7.3.4 Technical specifications Table 7- 7 RF330T technical specifications 6GT2800-5BA00 Product type designation SIMATIC RF330T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 8 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 1014 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1200 years Mechanical specifications Enclosure • Material • Plastic PPS • Color • Black Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 ... +100 °C • during storage • -40 to +100 ℃
RF300 transponder 7.3 SIMATIC RF330T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 243 6GT2800-5BA00 Degree of protection to EN 60529 • IP68 2 hours, 2 m, 20 ℃ • IPx9K steam jet: 150 mm; 10 to 15 l/min; 100 bar; 75 °C Pressure resistance • Low pressure resistant vacuum dryer: up to 20 mbar • high pressure resistant (see degree of protec-tion IPx9K) Shock-resistant acc. toEN 60721-3-7, Class 7 M31) 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (Ø x H) 30 x 8 mm Weight 10 g Type of mounting 1 x M4 screw 2) ≤ 1.5 Nm 1) The values for shock and vibration are maximum values and must not be applied continuously. 2 ) To prevent it loosening during operation, secure the screw with screw locking varnish. 7.3.5 Dimension drawing Figure 7-8 RF330T dimension drawing Dimensions in mm
RF300 transponder 7.4 SIMATIC RF340T SIMATIC RF300 244 System Manual, 07/2017, C79000-G8976-C345-07 7.4 SIMATIC RF340T 7.4.1 Features Table 7- 8 RF340T Characteristics Area of application Identification tasks on small assembly lines in harsh industrial environments Memory size • 8 KB FRAM user memory • 32 KB FRAM user memory Write/read range See section Field data of RF300 tran-sponders (Page 52) Mounting on metal Yes Degree of protection IP68/IPx9K 7.4.2 Ordering data Table 7- 9 Ordering data RF340T Article number RF340T 8 KB FRAM user memory 6GT2800-4BB00 RF340T 32 KB FRAM user memory 6GT2800-5BB00
RF300 transponder 7.4 SIMATIC RF340T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 245 7.4.3 Mounting on metal Direct mounting of the RF340T on metal is permitted. Mounting of RF340T on metal Figure 7-9 Mounting of RF340T on metal Flush-mounting of RF340T in metal: Figure 7-10 Flush-mounting of RF340T in metal The standard value for a is ≥ 20 mm. At lower values, the field data change significantly, resulting in a reduction in the range.
RF300 transponder 7.4 SIMATIC RF340T SIMATIC RF300 246 System Manual, 07/2017, C79000-G8976-C345-07 7.4.4 Technical specifications Table 7- 10 Technical specifications for RF340T 6GT2800-4BB00 6GT2800-5BB00 Product type designation SIMATIC RF340T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 8 KB FRAM / 32 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1010 Write cycles (at < 40 ℃) > 1010 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1200 years Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 to +85 ℃ • during storage • -40 to +85 ℃ Degree of protection to EN 60529 • IP68 • IPx9K Shock-resistant acc. toEN 60721-3-7, Class 7 M31) 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M31) 200 m/s2 Torsion and bending load Not permitted
RF300 transponder 7.4 SIMATIC RF340T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 247 6GT2800-4BB00 6GT2800-5BB00 Design, dimensions and weights Dimensions (L x W x H) 48 x 25 x 15 mm Weight 25 g Type of mounting 2 x M3 screws ≤ 1.0 Nm 1) The values for shock and vibration are maximum values and must not be applied continuously. 7.4.5 Dimension drawing Figure 7-11 RF340T dimension drawing Dimensions in mm
RF300 transponder 7.5 SIMATIC RF350T SIMATIC RF300 248 System Manual, 07/2017, C79000-G8976-C345-07 7.5 SIMATIC RF350T 7.5.1 Features RF350T Characteristics Area of application Identification tasks on small assembly lines in harsh industrial environments Memory size 32 KB FRAM user memory Write/read range See section Field data of RF300 tran-sponders (Page 52) Mounting on metal Yes Degree of protection IP68 7.5.2 Ordering data Table 7- 11 Ordering data RF350T Article number RF350T 6GT2800-5BD00
RF300 transponder 7.5 SIMATIC RF350T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 249 7.5.3 Mounting on metal Direct mounting of the RF350T on metal is permitted. Mounting of RF350T on metal Figure 7-12 Mounting of RF350T on metal Flush-mounting of RF350T in metal: Figure 7-13 RF350T flush-mounted in metal
RF300 transponder 7.5 SIMATIC RF350T SIMATIC RF300 250 System Manual, 07/2017, C79000-G8976-C345-07 The standard value for a is ≥ 20 mm. At lower values, the field data change significantly, resulting in a reduction in the range. 7.5.4 Mounting options Mounting with fixing frame The RF350T transponder can be mounted as shown with the fixing frame: Figure 7-14 Installation diagram Dimensions of the fixing frame Figure 7-15 RF350T fixing frame
RF300 transponder 7.5 SIMATIC RF350T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 251 7.5.5 Technical data Table 7- 12 Technical specifications for RF350T 6GT2800-5BD00 Product type designation SIMATIC RF350T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 32 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1010 Write cycles (at < 40 ℃) > 1010 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1200 years Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 to +85 ℃ • during storage • -40 to +85 ℃ Degree of protection to EN 60529 IP68 Shock-resistant acc. toEN 60721-3-7, Class 7 M31) 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 50 x 50 x 20 mm
RF300 transponder 7.5 SIMATIC RF350T SIMATIC RF300 252 System Manual, 07/2017, C79000-G8976-C345-07 6GT2800-5BD00 Weight 25 g Type of mounting 2 x M4 screws ≤ 1.5 Nm 1) The values for shock and vibration are maximum values and must not be applied continuously. 7.5.6 Dimension drawing Figure 7-16 RF350T dimension drawing Dimensions in mm
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 253 7.6 SIMATIC RF360T 7.6.1 Features RF360T Characteristics Area of application Identification tasks on small assembly lines in harsh industrial environments Memory size • 8 KB FRAM user memory • 32 KB FRAM user memory Write/read range see section Field data of RF300 tran-sponders (Page 52) Mounting on metal Yes, with spacer Degree of protection IP67 7.6.2 Ordering data Table 7- 13 Ordering data RF360T Article number RF360T 8 KB FRAM user memory 6GT2800-4AC00 RF360T 32 KB FRAM user memory 6GT2800-5AC00 Table 7- 14 Ordering data for RF360T accessories Article number Spacer (in conjunction with fixing pocket 6GT2190-0AB00) 6GT2190-0AA00 Fixing pocket (in conjunction with spacer 6GT2190-0AA00) 6GT2190-0AB00
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 254 System Manual, 07/2017, C79000-G8976-C345-07 7.6.3 Mounting on metal Direct mounting of the RF360T on metal is not allowed. A distance ≥ 20 mm is recommended. This can be achieved using the spacer 6GT2190-0AA00 in combination with the fixing pocket 6GT2190-0AB00. Mounting of RF360T on metal Figure 7-17 Mounting of RF360T with spacer The standard value for h is ≥ 20 mm. Flush-mounting of RF360T in metal: Figure 7-18 Flush-mounting of RF360T with spacer
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 255 The standard value for a is ≥ 20 mm. At lower values, the field data change significantly, resulting in a reduction in the range.
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 256 System Manual, 07/2017, C79000-G8976-C345-07 Dimensions of spacer and fixing pocket for RF360T Figure 7-19 Dimensions of spacer and fixing pocket for RF360T
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 257 7.6.4 Technical data Table 7- 15 Technical specifications for RF360T 6GT2800-4AC00 6GT2800-5AC00 Product type designation SIMATIC RF360T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 8 KB FRAM / 32 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1010 Write cycles (at < 40 ℃) > 1010 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1200 years Mechanical specifications Enclosure • Material • Epoxy resin • Color • Anthracite Recommended distance to metal ≥ 20 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +75 ℃ • outside the read/write field • -40 to +85 ℃ • during storage • -40 to +85 ℃ Degree of protection to EN 60529 IP67 Shock-resistant to EN 60721-3-7, Class 7 M3 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M3 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 86 x 55 x 2.5 mm
RF300 transponder 7.6 SIMATIC RF360T SIMATIC RF300 258 System Manual, 07/2017, C79000-G8976-C345-07 6GT2800-4AC00 6GT2800-5AC00 Weight 25 g Type of mounting • 2 x M3 screws ≤ 1.0 Nm • Fixing pocket (6GT2190-0AB00) 7.6.5 Dimension drawing Figure 7-20 RF360T dimension drawing Dimensions in mm
RF300 transponder 7.7 SIMATIC RF370T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 259 7.7 SIMATIC RF370T 7.7.1 Features The SIMATIC RF370T transponder is a passive (i.e. battery-free) data carrier in a square type of construction. RF370T Characteristics Area of application Identification tasks on assembly lines in harsh industrial environments, due to high resistance to oils, lubricants and cleaning agents, and suitable for larger ranges, e.g. automotive industry Memory size • 32 KB FRAM user memory • 64 KB FRAM user memory Write/read range see section Field data of RF300 transpond-ers (Page 52) Mounting on metal Yes Degree of protection IP68/IPx9K 7.7.2 Ordering data Table 7- 16 Ordering data RF370T Article number RF370T 32 KB FRAM user memory 6GT2800-5BE00 RF370T 64 KB FRAM user memory 6GT2800-6BE00
RF300 transponder 7.7 SIMATIC RF370T SIMATIC RF300 260 System Manual, 07/2017, C79000-G8976-C345-07 7.7.3 Mounting on metal Direct mounting of the RF370T on metal is permitted. Mounting of RF370T on metal Figure 7-21 Mounting of RF370T on metal Flush-mounting of RF370T in metal: Figure 7-22 RF370T flush-mounted in metal The standard value for a is ≥ 20 mm. At lower values, the field data change significantly, resulting in a reduction in the range.
RF300 transponder 7.7 SIMATIC RF370T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 261 7.7.4 Mounting instructions It is essential that you observe the instructions in the Section Installation guidelines (Page 67). Properties Description Type of installation Screw fixing (two M5 screws) Tightening torque < 1.2 Nm (at room temperature) 7.7.5 Technical specifications Table 7- 17 Technical specifications RF370T 6GT2800-5BE00 6GT2800-6BE00 Product type designation SIMATIC RF370T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 32 KB FRAM / 64 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1010 Write cycles (at < 40 ℃) > 1010 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1200 years Mechanical specifications Enclosure • Material • Plastic PA 12 • Color • Anthracite Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions
RF300 transponder 7.7 SIMATIC RF370T SIMATIC RF300 262 System Manual, 07/2017, C79000-G8976-C345-07 6GT2800-5BE00 6GT2800-6BE00 Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 to +85 ℃ • during storage • -40 to +85 ℃ Degree of protection to EN 60529 IPx9K Shock-resistant acc. toEN 60721-3-7, Class 7 M31) 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weights Dimensions (L x W x H) 75 x 75 x 41 mm Weight 200 g Type of mounting 2 x M5 screws ≤ 1.5 Nm 1) The values for shock and vibration are maximum values and must not be applied continuously. 7.7.6 Dimensional drawing Figure 7-23 RF370T dimension drawing Dimensions in mm
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 263 7.8 SIMATIC RF380T 7.8.1 Features The SIMATIC RF380T transponder is an extremely rugged and heat-resistant round data carrier suitable e.g. for applications in the automotive industry. SIMATIC RF380T transponder Characteristics Area of application Identification tasks in applications (e.g. automotive industry) with cyclic high temperature stress > 85 °C and < 220 °C Highly resistant to mineral oils, lubricants and cleaning agents Typical applications: • Primer coat, electrolytic dip area, cataphoresis with the associated drying furnaces • Top coat area with drying furnaces • Washing areas at temperatures > 85°C • Other applications with higher temperatures Memory size 32 KB FRAM user memory Write/read range see section "Field data of RF300 transponders (Page 52)" Mounting on metal Yes, flush-mounted in metal Degree of protection IP68 7.8.2 Ordering data Table 7- 18 Ordering data RF380T Article number RF380T User memory 32 KB FRAM (read/write) and 4 bytes EEPROM 6GT2800-5DA00 Table 7- 19 Ordering data for RF380T Article number Holder (short version) 6GT2090-0QA00 Holder (long version) 6GT2090-0QA00-0AX3 Shrouding cover 6GT2090-0QB00 Universal holder 6GT2590-0QA00
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 264 System Manual, 07/2017, C79000-G8976-C345-07 7.8.3 Installation guidelines for RF380T It is essential that you observe the instructions in the Section Installation guidelines (Page 67). The following section only deals with features specific to the SIMATIC RF380T. 7.8.3.1 Mounting instructions Note Only use tag with original holder You are strongly recommended to only use the tag with the original holder specified. Only this holder guarantees that the data memory observes the listed values for shock, vibration and temperature. A protective cover is recommendable for applications in paint shops. Data memory holder Short version (6GT2 090-0QA00) Long version (6GT2090-0QA00-0AX3) Material: V2A sheet-steel with thickness 2.5 mm BI 2.5 DIN 59382 1.4541
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 265 Assembly of data memory with holder Figure 7-24 Assembly of tag with holder Scope of supply The holder is provided with all mounting parts and a mounting diagram. Mounting screws for securing the holder are not included. The mounting screws are of diameter M 10. The minimum length is 25 mm. The optional cover can be used for the long and short versions of the holder.
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 266 System Manual, 07/2017, C79000-G8976-C345-07 Universal holder Figure 7-25 Universal holder 6GT2590-0QA00
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 267 7.8.3.2 Metal-free area Direct mounting of the RF380T on metal is permitted. Mounting of RF380T on metal Figure 7-26 Mounting of RF380T on metal Flush-mounting of RF380T in metal: Figure 7-27 RF380T flush-mounted in metal The standard value for a is ≥ 40 mm. At lower values, the field data change significantly, resulting in a reduction in the range.
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 268 System Manual, 07/2017, C79000-G8976-C345-07 7.8.4 Configuring instructions 7.8.4.1 Temperature dependence of the transmission window The guidelines in the section "Planning the RF300 system" apply to configuration of heat-resistant data memories, with the exception of the limit distance and field length at temperatures above 85 °C. At temperatures above 85 °C, the length of the transmission window is reduced by up to 10%. 7.8.4.2 Temperature response in cyclic operation At ambient temperatures (Tu) up to 110 °C, cyclic operation is not necessary, i.e. up to this temperature, the transponder can be in constant operation. Note Calculation of the temperature curves Calculation of the temperature curves or of a temperature profile can be carried out on request by Siemens AG. Exact knowledge of the internal temperature facilitates configuration for time-critical applications. You can also carry out the calculation with the aid of the "SIMATIC RF Temperature Calculator" on the "Ident Systems Software & Documentation" DVD (refer to the section "DVD "Ident Systems Software & Documentation" (Page 435)"). Ambient temperatures > 110 °C Note Cancellation of warranty The internal temperature of the data memory must not exceed the critical threshold of 110 °C. Each heating phase must be followed by a cooling phase. No warranty claims will otherwise be accepted. Some limit cycles are listed in the table below: Table 7- 20 Limit cycles of data memory temperature Tu (heating up) Heating up Tu (cooling down) Cooling down 220 °C 0.5 h 25 °C > 2 h 200 °C 1 h 25 °C > 2 h 190 °C 1 h 25 °C > 1 h 45 min 180 °C 2 h 25 °C > 5 h 170 °C 2 h 25 °C > 4 h
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 269 The internal temperature of the tag follows an exponential function with which the internal temperature and the operability of the tag can be calculated in advance. This is particularly relevant to temperature-critical applications or those with a complex temperature profile. Ambient temperatures > 220°C Note Cancellation of warranty The data memory must not be exposed to ambient temperatures > 220 °C. No warranty claims will otherwise be accepted. However, the mechanical stability is retained up to 230 °C! Example of a cyclic sequence Table 7- 21 Typical temperature profile of an application in the paint shop Start of tag at initial point Duration (min) Ambient temperature (°C) Electrolytic dip 20 30 Electrolytic dip dryer 60 200 Transport 60 25 PVC dryer 25 170 Transport 60 25 Filler dryer 60 160 Transport 60 25 Top coat dryer 60 120 Transport 60 25 Wax dryer 25 100 Transport 150 25
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 270 System Manual, 07/2017, C79000-G8976-C345-07 Figure 7-28 Graphic trend of temperature profile from above table The simulation results in the following: Following a simulation time of 36.5 hours, a total of 3 cycles were carried out, and an internal temperature of 90 degrees Celsius was reached. Figure 7-29 Complete temperature response due to simulation
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 271 7.8.5 Use of the transponder in the Ex protection area The TÜV SÜD Automotive GmbH as approved test center as well as the TÜV SÜD Product Service GmbH as certification center, identification number 0123, as per Article 9 of the Directive of the European Council of 23 March 1994 (94/9/EC), has confirmed the compliance with the essential health and safety requirements relating to the design and construction of equipment and protective systems intended for use in hazardous areas as per Annex II of the Directive. The essential health and safety requirements are satisfied in accordance with the following standards: Table 7- 22 Approvals Document Title EN 60079-0: 2006 Electrical equipment for hazardous gas atmospheres - Part 0: General requirements EN 60079-15: 2005 Electrical equipment for hazardous gas atmospheres - Part 15: Design, testing and identification of electrical equipment with type of protection "n" DIN VDE 0848-5: 2001 (in parts) Safety in electrical, magnetic and electromagnetic fields - Part 5: Explosion protection ZLS SK 107.1 Central office of the states for safety; test components Identification Table 7- 23 The identification of the electrical equipment as an encapsulated unit II 3G Ex nC IIB T5 -25°C to +70°C Um=30Vdc The equipment is assigned the following references: XXXYYYZZZ [= serial number, is assigned during production] TPS 09 ATEX 1 459 X [= certificate number] "No use of the equipment in the vicinity of processes generating high charges"
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 272 System Manual, 07/2017, C79000-G8976-C345-07 7.8.5.1 Use of the transponder in hazardous areas for gases Temperature class delineation for gases The temperature class of the transponder for hazardous areas depends on the ambient temperature range: Ambient temperature range Temperature class -25 °C to +70 °C T5 WARNING Ignitions of gas-air mixtures • When using the RF380T transponder, check that the temperature class is kept to in conjunction with the requirements of the area of application. If the temperature ranges are exceeded during use of the transponder, gas-air mixtures may be ignited. • The maximum transmit power of the transmitter used to operate the transponder must not exceed 2 W. If the transmit power id not kept to, gas-air mixtures may ignite. 7.8.5.2 Installation and operating conditions for the hazardous area a) Use of the equipment in the vicinity of processes generating high charges is not allowed. b) The equipment must be mechanically protected when installed. 7.8.6 Cleaning the mobile data memory Note Do not clean the transponder with mechanical tools, sand-blasting or pressure hose. These cleaning methods result in damage to the transponder. Clean the transponder only with the chemical cleansing agents listed in Chapter Chemical resistance of the readers and transponders (Page 97).
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 273 7.8.7 Technical specifications Table 7- 24 RF380T technical specifications 6GT2800-5DA00 Product type designation SIMATIC RF380T Memory Memory organization in bytes Memory configuration • UID • 4 bytes EEPROM • User memory • 32 KB FRAM • OPT memory • 20 bytes EEPROM Read cycles (at < 40 ℃) > 1010 Write cycles (at < 40 ℃) > 1010 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of RF300 transponders (Page 52)" MTBF (Mean Time Between Failures) 1177 years Mechanical specifications Enclosure • Material • PPS • Color • Anthracite Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 … +110 °C > 110 °C °C: cyclic operation possible • outside the read/write field • -40 ... +220 °C • during storage • -40 to +110 ℃ Degree of protection to EN 60529 IP68 Shock-resistant acc. to EN 60721-3-7, Class 7 M31)2) 500 m/s2 Vibration-resistant to EN 60721-3-7, Class 7 M32) 50 m/s2 Torsion and bending load Not permitted
RF300 transponder 7.8 SIMATIC RF380T SIMATIC RF300 274 System Manual, 07/2017, C79000-G8976-C345-07 6GT2800-5DA00 Design, dimensions and weights Dimensions (Ø x H) 114 x 83 mm Weight 900 g Type of mounting Holder (must be ordered separately) 1) Applies only in conjunction with the original support 2) The values for shock and vibration are maximum values and must not be applied continuously. 7.8.8 Dimensional drawing Figure 7-30 Dimension drawing RF380T Dimensions in mm
SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 275 ISO transponder 8 Features of the ISO transponders The transponders (MDS D) that are compatible with ISO 15693 represent a cost-effective alternative to RF300 transponders. The performance that can be achieved with this (transmission speed, memory size), however, is considerably less than with RF300 transponders. You will find more information on transmission speeds in the section "Communication between communications module, reader and transponder (Page 50)".
ISO transponder 8.1 Memory configuration of ISO the transponders SIMATIC RF300 276 System Manual, 07/2017, C79000-G8976-C345-07 8.1 Memory configuration of ISO the transponders Figure 8-1 Memory configuration of ISO the transponders
ISO transponder 8.1 Memory configuration of ISO the transponders SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 277 Memory areas Depending on the manufacturer of the transponder chip, the memory configuration of an ISO transponder consists of varying sizes of user memory. The typical sizes are 112 bytes, 256 bytes, 992 bytes EEPROM or 2000 bytes FRAM. Each ISO transponder chip has an 8-byte long unique serial number (UID, read only). This UID is transferred as an 8 byte value through a read command to address FFF0 with a length of 8. OTP area For the OTP area, a 16-byte address space is always reserved at the end of the memory area. The blocks are divided up depending on the chip (see technical specifications). Note that the corresponding addresses for the user data are therefore not available to the application when the OTP area is used. A total of 4 block addresses ("mapped" addresses) are provided: ● FF80 ● FF84 ● FF88 ● FF8C A write command to this block address with a valid length (4, 8, 12, 16 bytes depending on the block address) protects the written data from subsequent overwriting. Note Exception Fujitsu chip (MDS D4xx and MDS D5xx) The Fujitsu chip MB89R118 (MDS D4xx) has 8-byte blocks, which means that only 2 block addresses have to be addressed: FF80 and FF88 with the length 8 and 16 bytes). The Fujitsu chip MB89R112 (MDS D5xx) has 32 byte blocks and can therefore not be addressed in the OTP area. Note Restriction to the use of the OTP Observe the following restrictions when using OTP: • The OTP write/lock command can only be sent in static operation. • The OTP write/lock command can not be sent as a chained command. The Fujitsu chip MB89R112 (MDS D5xx) has 32 byte blocks and can therefore not be addressed in the OTP area. Note Use of the OTP area is not reversible If you use the OPT area, you cannot undo it, because the OPT area can only be written to once.
ISO transponder 8.2 MDS D100 SIMATIC RF300 278 System Manual, 07/2017, C79000-G8976-C345-07 8.2 MDS D100 8.2.1 Characteristics MDS D100 Characteristics Area of application From simple identification such as electronic barcode replacement/supplementation, through warehouse and distribution logistics, right up to product identification. Memory size 112 bytes of EEPROM user memory Write/read range See section Field data of ISO transponders (MDS D) (Page 56). Mounting on metal Yes, with spacer ISO standard ISO 15693 Degree of protection IP68 8.2.2 Ordering data Table 8- 1 Ordering data for MDS D100 Article number MDS D100 6GT2600-0AD10 Table 8- 2 Ordering data for MDS D100 accessory Article number Spacer (in conjunction with fixing pocket 6GT2190-0AB00) 6GT2190-0AA00 Fixing pocket (in conjunction with spacer 6GT2190-0AA00) 6GT2190-0AB00 Fixing pocket (not suitable for fixing directly onto metal) 6GT2390-0AA00
ISO transponder 8.2 MDS D100 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 279 8.2.3 Metal-free area Direct mounting of the MDS D100 on metal is not allowed. A distance of ≥ 20 mm is recommended. This can be achieved using the spacer 6GT2190-0AA00 in combination with the fixing pocket 6GT2190-0AB00. Mounting on metal h ≥ 20 mm ① Transponder ② Metal ③ Non-metal Figure 8-2 Mounting of the MDS D100 on metal with spacer
ISO transponder 8.2 MDS D100 SIMATIC RF300 280 System Manual, 07/2017, C79000-G8976-C345-07 Flush-mounting a ≥ 20 mm h ≥ 20 mm ① Transponder ② Metal ③ Non-metal Figure 8-3 Flush-mounting of MDS D100 in metal with spacer Note If the minimum guide values (h or a) are not observed, a reduction of the field data results.
ISO transponder 8.2 MDS D100 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 281 8.2.4 Technical data Table 8- 3 Technical specifications for MDS D100 6GT2600-0AD10 Product type designation SIMATIC MDS D100 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PET • Color • White/black Recommended distance to metal ≥ 20 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +80 ℃ • outside the read/write field • -25 to +80 ℃ • during storage • -25 to +80 ℃ Degree of protection to EN 60529 IP68 Shock-resistant to EN 60721-3-7 class 7M3 ISO 10373 / ISO 7810 1) Vibration-resistant to EN 60721-3-7, class 7M3 ISO 10373 / ISO 7810 1) Torsion and bending load ISO 10373/ISO 7816-1 Design, dimensions and weight Dimensions (L x W x H) 85.6 x 54 x 0.9 mm
ISO transponder 8.2 MDS D100 SIMATIC RF300 282 System Manual, 07/2017, C79000-G8976-C345-07 6GT2600-0AD10 Weight 5 g Type of mounting • Fixing pocket • Glued 2) 1) The values for shock and vibration are maximum values and must not be applied continuously. 2) The processing instructions of the adhesive manufacturer must be observed. 8.2.5 Dimension drawing Dimensions in mm 1) Dimensions for mounting holes Figure 8-4 MDS D100 dimension drawing
ISO transponder 8.3 MDS D117 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 283 8.3 MDS D117 8.3.1 Features MDS D117 Characteristics Area of application Very compact data carrier that can be cemented into objects where precise positioning is necessary; e.g. tool identification, workpiece holders etc.. Memory size 112 bytes of EEPROM user memory Write/read range See section "Field data of ISO transponders (MDS D) (Page 56)." Mounting in metal Yes, flush-mounted in metal ISO standard ISO 15693 Degree of protection IP68/IPx9K 8.3.2 Ordering data Table 8- 4 Ordering data for MDS D117 Article number MDS D117 Pack of 10 6GT2600-0AG00
ISO transponder 8.3 MDS D117 SIMATIC RF300 284 System Manual, 07/2017, C79000-G8976-C345-07 8.3.3 Mounting in metal Flush-mounted in metal ① Transponder ② Metal 8.3.4 Technical specifications Table 8- 5 Technical specifications for MDS D117 6GT2600-0AG00 Product type designation SIMATIC MDS D117 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PPS • Color • Black
ISO transponder 8.3 MDS D117 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 285 6GT2600-0AG00 Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 to +125 ℃ • during storage • -40 to +125 ℃ Degree of protection to EN 60529 IP68 2 hours, 2 bar, +20 °C Shock according to EN 60721-3-7 Class 7M31) 1000 m/s2 Vibration according to EN 60721-3-7 Class 7M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (Ø x H) 4 x 5.2 mm Weight 1 g Type of mounting • Fixing pocket • Glued 2) 1) The values for shock and vibration are maximum values and must not be applied continuously. 2) The processing instructions of the adhesive manufacturer must be observed. 8.3.5 Dimension drawing Figure 8-5 Dimensions in mm
ISO transponder 8.4 MDS D124 SIMATIC RF300 286 System Manual, 07/2017, C79000-G8976-C345-07 8.4 MDS D124 8.4.1 Characteristics MDS D124 Characteristics Area of application Application areas in production automation (e.g. small paintshops up to +180 °C) Memory size 112 bytes of EEPROM user memory Write/read range See section "Field data of ISO transponders (MDS D) (Page 56)". Mounting on metal Yes, with spacer ISO standard ISO 15693 Degree of protection IP68/IPx9K 8.4.2 Ordering data Table 8- 6 Ordering data for MDS D124 Article number MDS D124 6GT2600-0AC10 Table 8- 7 Ordering data for MDS D124 accessories Article number Spacer 6GT2690-0AK00
ISO transponder 8.4 MDS D124 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 287 8.4.3 Mounting on metal Mounting on metal h ≥ 15 mm Figure 8-6 Mounting the MDS D124/D324/D424/D524/E624 and RF320T on metal with spacer Flush-mounting h ≥ 15 mm a ≥ 25 mm Figure 8-7 Flush-mounting of the MDS D124/D324/D424/D524/E624 and RF320T in metal with spacer
ISO transponder 8.4 MDS D124 SIMATIC RF300 288 System Manual, 07/2017, C79000-G8976-C345-07 Note Going below the distances If the distances (a and h) are not observed, a reduction of the field data results. It is possible to mount the MDS with metal screws (M3 countersunk head screws). This has no tangible impact on the range. 8.4.4 Technical specifications Table 8- 8 Technical specifications for MDS D124 6GT2600-0AC10 Product type designation SIMATIC MDS D124 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PPS • Color • Black Recommended distance to metal ≥ 15 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 … +140 °C • from +125 ℃: 20% reduction in the limit dis-tance • outside the read/write field • -40 to +180 ℃
ISO transponder 8.4 MDS D124 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 289 6GT2600-0AC10 • at +180 ℃: Tested up to 5000 hours or 3000 cycles • during storage • -40 to +125 ℃ Degree of protection to EN 60529 • IP68 2 hours, 2 bar, +20 °C • IPx9K steam jet: 150 mm; 10 to 15 l/min; 100 bar; 75 °C Shock according to EN 60721-3-7 Class 7M31) 1000 m/s2 Vibration according to EN 60721-3-7 Class 7M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (Ø x H) 4 x 5.2 mm Weight 5 g Type of mounting • 1 x M3 screw 2) ≤ 1 Nm • Glued 3) • With spacer 1) The values for shock and vibration are maximum values and must not be applied continuously. 2 ) To prevent it loosening during operation, secure the screw with screw locking varnish. 3) The processing instructions of the adhesive manufacturer must be observed. 8.4.5 Use of the MDS D124 in hazardous area The mobile data memory MDS D124, device group II, category 1G or 1D may be installed and operated in zones 0, 1 and 2 or in the zones 20, 21 and 22. The following requirements of the 94/9/EC directive are met: ● EN 60079-0:2009 ● EN 60079-11:2007 ● EN 61241-11:2006 ● EN 60079-26:2007 When used in hazardous areas, the MDS D124 must not be operated with field strengths > 5 A / m to avoid impermissible heating. This is not the case with readers from the SIMATIC RF range (MOBY D, RF200 and RF300).
ISO transponder 8.4 MDS D124 SIMATIC RF300 290 System Manual, 07/2017, C79000-G8976-C345-07 Identification II 1 G Ex ia IIC T3 to T6 Ga or II 1 D Ex ia IIIC T80 °C to T180 °C Da TÜV 12 ATEX 084413 X The temperature class or the maximum surface temperature depends on the maximum ambient temperature. The relationship between temperature class (gas) or maximum surface temperature (dust) can be found in the following table. Table 8- 9 Ambient temperature Ambient temperature range Temperature class Max. surface temperature -25 ... +150 ℃ T3 T180 -25 ... +100 ℃ T4 T130 -25 ... +65 ℃ T5 T95 -25 ... +50 ℃ T6 T80 Note Safety markings for hazardous areas Since there is not enough space on the MDS D124 for the safety mark, this is supplied as a label with the device. This must be affixed immediately next to the MDS D124 so that the label clearly relates to the device. WARNING Gefahr durch elektrostatische Entladungen Potential electrostatic charging hazard Danger potentiel de charges électrostatiques
ISO transponder 8.4 MDS D124 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 291 Note Installation and operating conditions for hazardous areas: • Use of the device in the vicinity of processes generating high charges is not allowed. • The device must be installed so that it is mechanically protected. • For applications requiring devices of category 1, the device must be mounted on a grounded, conductive base. • It must only be cleaned with a damp cloth. • The device is suitable for use in atmospheres containing dust, however not for full immersion in dust. 8.4.6 Dimension drawing Figure 8-8 Dimension drawing of MDS D124 All dimensions in mm
ISO transponder 8.5 MDS D126 SIMATIC RF300 292 System Manual, 07/2017, C79000-G8976-C345-07 8.5 MDS D126 8.5.1 Characteristics MDS D126 Characteristics Area of application Compact and rugged ISO transponder; suitable for identification of transport units in production-related logistics; can also be deployed in harsh conditions Memory size 112 bytes of EEPROM user memory Write/read range See section Field data of ISO transponders (MDS D) (Page 56) Mounting on metal Yes, with spacer ISO standard ISO-15693 Degree of protection IP68 8.5.2 Ordering data Table 8- 10 Ordering data for MDS D126 Article number MDS D126 6GT2600-0AE00 Table 8- 11 Ordering data for MDS D126 accessories Article number Spacer 6GT2690-0AL00
ISO transponder 8.5 MDS D126 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 293 8.5.3 Mounting on metal Mounting on metal h ≥ 25 mm Figure 8-9 Mounting the MDS D126 / D426 / D526 on metal with spacer Flush-mounted in metal h ≥ 25 mm a ≥ 50 mm Figure 8-10 Flush installation of the MDS D126 / D426 / D526 in metal with spacer
ISO transponder 8.5 MDS D126 SIMATIC RF300 294 System Manual, 07/2017, C79000-G8976-C345-07 8.5.4 Technical specifications Table 8- 12 Technical specifications for the MDS D126 6GT2600-0AE00 Product type designation SIMATIC MDS D126 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PA6.6 GF • Color • Black Recommended distance to metal ≥ 25 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +85 ℃ • outside the read/write field • -40 to +100 ℃ • during storage • -40 to +100 ℃ Degree of protection to EN 60529 IP68 2 hours, 2 bar, +20 °C Shock according to EN 60721-3-7 Class 7M31) 500 m/s2 Vibration according to EN 60721-3-7 Class 7M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (Ø x H) 50 x 3.6 mm
ISO transponder 8.5 MDS D126 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 295 6GT2600-0AE00 Weight 13 g Type of mounting • 1 x M4 screw 2) ≤ 1 Nm • Glued 3) 1) The values for shock and vibration are maximum values and must not be applied continuously. 2 ) To prevent it loosening during operation, secure the screw with screw locking varnish. 3) The processing instructions of the adhesive manufacturer must be observed. 8.5.5 Dimension drawing Dimensions in mm Figure 8-11 Dimension drawing of MDS D126
ISO transponder 8.6 MDS D127 SIMATIC RF300 296 System Manual, 07/2017, C79000-G8976-C345-07 8.6 MDS D127 8.6.1 Features MDS D127 Characteristics Area of application Very compact data carrier that can be screwed into areas where precise positioning is necessary; e.g. tool identification, workpiece holders etc. Memory size 112 bytes of EEPROM user memory Write/read range See section "Field data of ISO transponders (MDS D) (Page 56)" Mounting on metal Yes, flush-mounted in metal ISO standard ISO 15693 Degree of protection IP68/IPx9K 8.6.2 Ordering data Table 8- 13 Ordering data for MDS D127 Article number MDS D127 Pack of 10 (A screw-in aid is supplied with each pack) 6GT2600-0AF00
ISO transponder 8.6 MDS D127 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 297 8.6.3 Mounting in metal Flush-mounted in metal ① Metal ② Transponders Note Damage to the transponder due to improper mounting To screw the MDS D127 into a suitable thread, use the supplied screw-in tool. This avoids damage to the MDS D127. Figure 8-12 Screw-in aid for mounting the MDS D127
ISO transponder 8.6 MDS D127 SIMATIC RF300 298 System Manual, 07/2017, C79000-G8976-C345-07 8.6.4 Technical specifications Table 8- 14 Technical specifications for MDS D127 6GT2600-0AF00 Product type designation SIMATIC MDS D127 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PA6 • Color • Black Recommended distance to metal ≥ 0 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 to +100 ℃ • outside the read/write field • -40 to +125 ℃ • during storage • -40 to +125 ℃ Degree of protection to EN 60529 • IP68 2 hours, 2 bar, +20 °C • IPx9K steam jet: 150 mm; 10 to 15 l/min; 100 bar; 75 °C Shock according to EN 60721-3-7 Class 7M31) 1000 m/s2 Vibration according to EN 60721-3-7 Class 7M31) 200 m/s2 Torsion and bending load Not permitted
ISO transponder 8.6 MDS D127 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 299 6GT2600-0AF00 Design, dimensions and weight Dimensions (Ø x H) M6 x 5.8 mm Weight 1 g Type of mounting • Glued 2) • 1 x M3 screw 1) The values for shock and vibration are maximum values and must not be applied continuously. 2) The processing instructions of the adhesive manufacturer must be observed. 8.6.5 Dimension drawing Figure 8-13 Dimensions in mm
ISO transponder 8.7 MDS D139 SIMATIC RF300 300 System Manual, 07/2017, C79000-G8976-C345-07 8.7 MDS D139 8.7.1 Characteristics MDS D139 Characteristics Area of application Applications in production logistics and in assembly lines subject to high temperatures (up to +220 °C) Typical application areas: • Paintshops and their preparatory treatments) • Primer coat, electrolytic dip area, cataphoresis with the associated drying furnaces • Top coat area with drying furnaces • Washing areas at temperatures > 85 °C • Other applications with higher temperatures Memory size 112 bytes of EEPROM user memory Write/read range See section Field data of ISO transponders (MDS D) (Page 56). Mounting on metal Yes, with spacer ISO standard ISO 15693 Degree of protection IP68/IPx9K Note Compatibility with SIMATIC RF300 depending on the article number The transponder MDS D139 with article number 6GT2600-0AA10 is compatible with the SIMATIC RF300 system. The transponder MDS D139 with article number 6GT2600-0AA00 is not compatible.
ISO transponder 8.7 MDS D139 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 301 8.7.2 Ordering data Table 8- 15 Ordering data for MDS D139 Article number MDS D139 6GT2600-0AA10 Table 8- 16 Ordering data for MDS D139 accessory Article number Spacer 6GT2690-0AA00 Quick change holder (Ø x H): 22 x 60 mm 6GT2690-0AH00 Quick change holder (Ø x H): 22 x 47 mm 6GT2690-0AH10 8.7.3 Mounting on metal Direct mounting of the MDS D139/D339 on metal is not allowed. A distance of ≥ 30 mm is recommended. This can be achieved using spacers (see "Ordering data (Page 441)"). Mounting on metal h ≥ 30 mm Figure 8-14 Mounting the MDS D139/D339 on metal with spacer
ISO transponder 8.7 MDS D139 SIMATIC RF300 302 System Manual, 07/2017, C79000-G8976-C345-07 Flush-mounting It is possible to mount the MDS D139/D339 in metal. With large antennas, for example ANT D5, this leads to a reduction of ranges. h ≥ 30 mm a ≥ 100 mm Figure 8-15 Flush-mounting of the MDS D139/D339 in metal with spacer Note Going below the distances If the distances (a and h) are not observed, a reduction of the field data results. It is possible to mount the MDS with metal screws (M5). This has no tangible impact on the range. It is recommended that a test is performed in critical applications. 8.7.4 Cleaning the mobile data memory Note Do not clean the transponder with mechanical tools, sand-blasting or pressure hose. These cleaning methods result in damage to the transponder. Clean the transponder only with the chemical cleansing agents listed in Chapter Chemical resistance of the readers and transponders (Page 97).
ISO transponder 8.7 MDS D139 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 303 8.7.5 Technical specifications Table 8- 17 Technical specifications for MDS D139 6GT2600-0AA10 Product type designation SIMATIC MDS D139 Memory Memory configuration • UID • 8 bytes • User memory • 112 bytes EEPROM • OTP memory • 16 bytes (EEPROM) Read cycles (at < 40 ℃) > 1014 Write cycles (at < 40 ℃) > 106 Data retention time (at < 40 ℃) > 10 years Write/read distance (Sg) Dependent on the reader used, see section "Field data of ISO transponders (MDS D) (Page 56)" MTBF (Mean Time Between Failures) 228 years Mechanical specifications Housing • Material • PPS • Color • Black Recommended distance to metal ≥ 30 mm Power supply Inductive, without battery Permitted ambient conditions Ambient temperature • during write/read access • -25 … +140 °C • from +125 ℃: 20% reduction in the limit dis-tance • outside the read/write field • -40 to +220 ℃ • at +200 ℃: Tested up to 5000 hours or 6000 cycles • at +220 ℃: Tested up to 2000 hours or 2000 cycles • during storage • -40 to +100 ℃
ISO transponder 8.7 MDS D139 SIMATIC RF300 304 System Manual, 07/2017, C79000-G8976-C345-07 6GT2600-0AA10 Degree of protection to EN 60529 • IP68 2 hours, 2 bar, +20 °C • IPx9K steam jet: 150 mm; 10 to 15 l/min; 100 bar; 75 °C Shock according to EN 60721-3-7 Class 7M31) 500 m/s2 Vibration according to EN 60721-3-7 Class 7M31) 200 m/s2 Torsion and bending load Not permitted Design, dimensions and weight Dimensions (Ø x H) 85 x 15 mm Weight 50 g Type of mounting 1 x M5 screw 2) 1.5 Nm 1 The values for shock and vibration are maximum values and must not be applied continuously. 2) For mounting with the spacer (6GT2690-0AA00), use a stainless steel M5 screw to avoid damag-ing the MDS in high temperatures (expansion coefficient). 8.7.6 Use of the MDS D139 in hazardous areas The MDS D139 mobile data memory is classed as a piece of simple, electrical equipment and can be operated in Protection Zone 2, Device Group II, Category 3G. The following requirements of the 94/9/EC directive are met: ● EN 60079-0:2006 ● EN 60079-15:2005 ● EN 61241-0:2006 ● EN 61241-1:2004
ISO transponder 8.7 MDS D139 SIMATIC RF300 System Manual, 07/2017, C79000-G8976-C345-07 305 Identification II 3 G Ex nA II T2 II 3 D Ex tD A22 IP68 T 220°C KEMA 09 ATEX 0133 X Ta: -25 ... +220°C WARNING Gefahr durch elektrostatische Entladungen Potential electrostatic charging hazard Danger potentiel de charges électrostatiques Note Installations- und Betriebsbedingungen für den Ex-Schutzbereich: a) Der Einsatz des Gerätes in der Nähe von stark ladungserzeugenden Prozessen ist untersagt. b) Das Gerät ist mechanisch geschützt zu montieren. c) Die Montage muss auf einem geerdeten, leitenden Untergrund erfolgen. d) Die Reinigung darf nur mit feuchtem Tuch erfolgen. Installation and operating conditions for hazardous areas: a) Use of the equipment in the vicinity of processes generating high charges is not allowed. b) The equipment must be mechanically protected when installed. c) Installation must be performed on a grounded and conductive mounting surface. d) Cleaning only with a wet cloth Conditions d'installation et de mise en oeuvre pour la zone de protection Ex : a) L'utilisation de l'appareil près de processus générant de fortes charges est interdite. b) L'appareil doit être monté de manière à être protégé mécaniquement. c) Le montage doit être effectué sur un socle conducteur mis à la terre. d) Nettoyage uniquement avec un chiffon humide
ISO transponder 8.7 MDS D139 SIMATIC RF300 306 System Manual, 07/2017, C79000-G8976-C345-07 8.7.7 Dimension drawings Dimensional drawing of MDS D139 Figure 8-16 Dimensional drawing of MDS D139 Dimensions in mm

Navigation menu