Siemens Canada Siemens Milltronics Process Instruments LR560 SITRANS LR560 Tank Level Probing Radar User Manual LY01 LR560FF

Siemens Canada Ltd. - Siemens Milltronics Process Instruments SITRANS LR560 Tank Level Probing Radar LY01 LR560FF

UserManual.wiki >

Siemens Canada Siemens Milltronics Process Instruments >

LR560 User Manual >

User Manual 3

Radar TransmittersOperating Instructions 10/2010SITRANS LR560 (Foundation Fieldbus)SITRANSDraft_Rev. 1.0-02Firmware 1.00.00-32

© Siemens AG 2010 Safety Guidelines: Warning notices must be observed to ensure personal safety as well as that of others, and to protect the product and the connected equipment. These warning notices are accompanied by a clarification of the level of caution to be observed. Qualified Personnel: This device/system may only be set up and operated in conjunction with this manual. Qualified personnel are only authorized to install and operate this equipment in accordance with established safety practices and standards. Unit Repair and Excluded Liability: • The user is responsible for all changes and repairs made to the device by the user or the user’s agent. • All new components are to be provided by Siemens Milltronics Process Instruments. • Restrict repair to faulty components only. • Do not reuse faulty components. Warning: Cardboard shipping package provides limited humidity and moisture protection. This product can only function properly and safely if it is correctly transported, stored, installed, set up, operated, and maintained. This product is intended for use in industrial areas. Operation of this equipment in a residential area may cause interference to several frequency based communications. Note: Always use product in accordance with specifications. Copyright Siemens AG 2010. All Rights Reserved Disclaimer of Liability This document is available in bound version and in electronic version. We encourage users to purchase authorized bound manuals, or to view electronic versions as designed and authored by Siemens Milltronics Process Instruments. Siemens Milltronics Process Instruments will not be responsible for the contents of partial or whole reproductions of either bound or electronic versions. While we have verified the contents of this manual for agreement with the instrumentation described, variations remain possible. Thus we cannot guarantee full agreement. The contents of this manual are regularly reviewed and corrections are included in subsequent editions. We welcome all suggestions for improvement. Technical data subject to change. MILLTRONICS®is a registered trademark of Siemens Milltronics Process Instruments. Contact SMPI Technical Publications European Authorized Representative at the following address: Technical Publications Siemens AG Siemens AG Industry Sector Siemens Milltronics Process Instruments 76181 Karlsruhe 1954 Technology Drive, P.O. Box 4225 Deutschland Peterborough, Ontario, Canada, K9J 7B1 Email: techpubs.smpi@siemens.com • For a selection of Siemens Milltronics level measurement manuals, go to: www. siemens.com/processautomation. Under Process Instrumentation, select Level Measurement and then go to the manual archive listed under the product family. • For a selection of Siemens Milltronics weighing manuals, go to: www. siemens.com/processautomation. Under Weighing Technology, select Continuous Weighing Systems and then go to the manual archive listed under the product family.

iiimmmmmTable of ContentsTrend ............................................................................................................................... 109Electronics Temperature............................................................................................ 109Peak Values................................................................................................................... 109Service...................................................................................................................................... 110Master Reset................................................................................................................. 110Remaining Device Lifetime ........................................................................................ 111Remaining Sensor Lifetime........................................................................................ 113Service Schedule ......................................................................................................... 115Calibration Schedule ................................................................................................... 117Powered Hours............................................................................................................. 119Power-on Resets.......................................................................................................... 119Menu Timeout............................................................................................................... 119LCD Backlight................................................................................................................ 119LCD Contrast.................................................................................................................. 119Secondary Value .......................................................................................................... 120Simulate Enable............................................................................................................ 120Demo Mode................................................................................................................... 120Communication....................................................................................................................... 120Tag ................................................................................................................................... 120Device Address............................................................................................................. 121Manufacturer ................................................................................................................ 121Device Type Identification.......................................................................................... 121Device Revision ............................................................................................................ 121ITK Version..................................................................................................................... 121Security..................................................................................................................................... 121Remote Access............................................................................................................. 121Local Access ................................................................................................................. 122Language.................................................................................................................................. 122Appendix A: Alphabetical Parameter List .................................................................. 123Appendix B: Troubleshooting ....................................................................................... 128Communication Troubleshooting ....................................................................................................128Device Status Icons ............................................................................................................................129General Fault Codes ...........................................................................................................................130Operation Troubleshooting ...............................................................................................................134 ..................................................................................................................................................................135Appendix C: Maintenance ............................................................................................ 136Unit Repair and Excluded Liability ..................................................................................................136Appendix D: Technical Reference ............................................................................... 137Principles of Operation ......................................................................................................................137Process Variables ......................................................................................................................137Echo Processing ..................................................................................................................................138Process Intelligence .................................................................................................................138Echo Selection ...........................................................................................................................138Measurement Range .........................................................................................................................143Measurement Response ...................................................................................................................144Damping .................................................................................................................................................144Loss of Echo (LOE) ...............................................................................................................................144

ivmmmmmTable of ContentsLoss of Echo (LOE) Timer (2.3.4.) ............................................................................................145Temperature derating curves ...........................................................................................................145Appendix E: Communications ..................................................................................... 147Foundation Fieldbus (FF) Protocol .........................................................................................147Field Communicator 375 (FC375) ............................................................................................147Appendix F: Firmware Revision History ..................................................................... 148Glossary ............................................................................................................................ 149Index .................................................................................................................................. 153LCD menu structure ....................................................................................................... 155

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 1mmmmmSITRANS LR560 (FF)Safety NotesSpecial attention must be paid to warnings and notes highlighted from the rest of the text by grey boxes.1)Safety marking symbolsFCC ConformityUS Installations only: Federal Communications Commission (FCC) rules WARNING symbol relates to a caution symbol on the product, and means that failure to observe the necessary precautions can result in death, serious injury, and/or considerable material damage.WARNING symbol, used when there is no corresponding caution symbol on the product, means that failure to observe the necessary precautions can result in death, serious injury, and/or considerable material damage.Note: means important information about the product or that part of the operating manual.1) This symbol is used when there is no corresponding caution symbol on the product.In manual On product DescriptionEarth (ground) TerminalProtective Conductor Terminal(Label on product: yellow background.) WARNING: refer to accompanying documents (manual) for details.WARNING: Changes or modifications not expressly approved by Siemens Milltronics could void the user’s authority to operate the equipment.Notes:• This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.• This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference to radio communications, in which case the user will be required to correct the interference at his own expense.

Page 2 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSITRANS LR560 (FF)CE Electromagnetic Compatibility (EMC) ConformityThis equipment has been tested and found to comply with the following EMC Standards:Industry Canadaa) Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.b) This device shall be installed and operated in a completely enclosed container to prevent RF emission which otherwise can interfere with aeronautical navigation. Installation shall be done by trained installers, in strict compliance with the manufacturer’s instructions.c) The use of this device is on a “no-interference, no-protection” basis. That is, the user shall accept operations of high-powered radar in the same frequency band which may interfere with or damage this device. On the other hand, level probing devices found to interfere with primary licensing operations will be required to be removed at the user’s expense.EMC Standard TitleCISPR 11:2004/EN 55011:1998+A1:1999&A2:2002, CLASS B Limits and methods of measurements of radio disturbance characteristics of industrial, scientific, and medical (ISM) radio-frequency equipment. EN 61326:1997+A1:1998+A2:2001+A3:2003 (IEC 61326:2002) Electrical Equipment for Measurement, Control and Laboratory Use – Electromagnetic Compatibility.EN61000-4-2:2001 Electromagnetic Compatibility (EMC) Part 4-2:Testing and measurement techniques – Electrostatic discharge immunity test. EN61000-4-3:2002 Electromagnetic Compatibility (EMC) Part 4-3: Testing and measurement techniques – Radiated, radio-frequency, electromagnetic field immunity test.EN61000-4-4:2004 Electromagnetic Compatibility (EMC) Part 4-4: Testing and measurement techniques – Electrical fast transient/burst immunity test.EN61000-4-5:2001 Electromagnetic Compatibility (EMC) Part 4-5: Testing and measurement techniques – Surge immunity test.EN61000-4-6:2004 Electromagnetic Compatibility (EMC) Part 4-6: Testing and measurement techniques – Immunity to conducted disturbances, induced by radio-frequency fields. EN61000-4-8:2001 Electromagnetic Compatibility (EMC) Part 4-8:Testing and measurement techniques – Power frequency magnetic field immunity test.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 3mmmmmSITRANS LR560 (FF)d) This level probing device is only permitted for installation inside enclosed containers. The installer/user of this device shall ensure that it is at least 10 km from the Penticton radio astronomy station (British Columbia latitude: 49° 19' 12" N, longitude: 119° 37'12" W). For devices not meeting this 10 km separation (e.g. the Okanagan Valley, British Columbia) the installer/ user must coordinate with and obtain the written concurrence of the Director of the Penticton radio astronomy station before the equipment can be installed or operated. The Penticton contact is Tel: 250-493-2277/ fax: 250-493-7767. (In case of difficulty, the Manager, Radio Equipment Standards, Industry Canada, may also be contacted.)The ManualThis manual will help you set up your SITRANS LR560 for optimum performance. Foundation Fieldbus for Level instruments (7ML19985MP01) manual provides details on FF communication. 1)We always welcome suggestions and comments about manual content, design, and accessibility. Please direct your comments to techpubs.smpi@siemens.com. For other Siemens Milltronics level measurement manuals, go to:www.siemens.com/level, and look under Level Measurement.Application ExampleThe application example used in this manual illustrates a typical installation using SITRANS LR560. (See Level application example on page 40.) Because there is often a range of ways to approach an application, other configurations may also apply. In all examples, substitute your own application details. If the example does not apply to your application, check the applicable parameter reference for the available options.Notes:• This product is intended for use in industrial areas. Operation of this equipment in a residential area may cause interference to several frequency based communications.• Please follow the installation and operating procedures for a quick, trouble-free installation and to ensure the maximum accuracy and reliability of your SITRANS LR560. • This manual applies to the SITRANS LR560 (FOUNDATION™ Fieldbus)1) only.1) FOUNDATION™ Fieldbus is a trademark of Fieldbus Foundation.

Page 4 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSITRANS LR560 (FF)Technical SupportSupport is available 24 hours a day. To find your local Siemens Automation Office address, phone number and fax number go to:www.siemens.com/automation/partner• Click on the tab Contact, select Service, then click Service again to find your product group (+Automation Technology > +Sensor Systems >+Process Instrumentation > +Level Measurement > +Continous). Select Radar.• Select the country followed by the City/Region. • Select Technical Support under Service.For on-line technical support go to:www.siemens.com/automation/support-request • Enter the device name (SITRANS LR560) or order number, then click on Search, and select the appropriate product type. Click on Next.• You will be prompted to enter a keyword describing your issue. Then either browse the relevant documentation, or click on Next to email a detailed description of your issue to Siemens Technical Support staff.Siemens IA/DT Technical Support Center: phone +49 (0)911 895 7 222Abbreviations and IdentificationsShort form Long Form Description UnitsAIFB Analog Input Function BlockCE / FM / CSAConformité Européenne / Factory Mutual / Canadian Standards Associationsafety approvalDCS Distributed Control System process controlDD See EDDDIAG TB Diagnostic Transducer BlockdK dielectric constantEDD Electronic Device Description (also referred to as DD)FF Foundation Fieldbus communication protocolFMCW Frequency Modulated Continous Wave radar principle

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 5mmmmmSITRANS LR560 (FF)H1 31.25 kbps 2-wire fieldbus protocolHSE High Speed Ethernet communication protocolITK Interoperability Test KitIiInput current mAIoOutput current mALAS Link Active SchedulerLCD Liquid Crystal DisplayLDI Local Display Interface removable display with push buttonsLTB Level Transducer BlockLUI Local User Interfaceview outputs via LCD display; make modifications via push buttons or handheld programmerμsmicrosecond 10-6 SecondPED Pressure Equipment Directive safety approvalPID FB Proportional Integral Derivative Function Blockppm parts per millionPV Primary Value measured valueRES Resource BlockSELV Safety extra low voltageSV Secondary Value equivalent valueTVT Time Varying Threshold sensitivity thresholdUiInput voltage VUoOutput voltage VShort form Long Form Description Units (cont’d)

Page 6 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSITRANS LR560 (FF)SITRANS LR560 OverviewSITRANS LR560 is a 2-wire, 78 GHz FMCW radar level transmitter for continuous monitoring of solids in vessels to a range of 100 m (329 ft). The plug and play performance is ideal for all solids applications, including those with extreme dust and high temperatures to +200 °C (+392 °F). The device consists of an electronic circuit coupled to a lens antenna and flange for quick and easy positioning. The main benefits of using 78 GHz over devices using lower frequency are:• very narrow beam, so device is insensitive to mounting nozzle interference and vessel obstructions.• short wavelength yields very good reflection properties on sloped solids, so aiming towards material angle of repose is usually not necessary.The technology is very tolerant of buildup on the lens antenna, however an air purge inlet is provided for periodic cleaning if required. SITRANS LR560 supports Foundation Fieldbus communication protocol, and AMS Device Manager software. Signals are processed using Process Intelligence which has been field-proven in over 1,000,000 applications worldwide (ultrasonic and radar). This device can be configured as an FF (H1) Link Master.ProgrammingSITRANS LR560 is very easy to install and configure via an optional graphical local display interface (LDI). You can modify the built-in parameters either locally, using the control buttons or the infrared handheld programmer, or from a remote location using one of the following options:•PROFIBUS PA [using SIMATIC PDM, or FDT (such as PACTware). See SITRANS LR560 (PROFIBUS PA) Instruction Manual for more information.]•HART [using handheld 375 Field Communicator, SIMATIC PDM, AMS, or FDT (such as PACTware). See SITRANS LR560 (mA/HART) Instruction Manual for more information.]•Foundation Fieldbus (FF) [using handheld 375 Field Communicator, an FF host system, or AMS]. Once programmed, the graphic Local Display Interface (LDI) can be removed if desired and used to transfer parameters to multiple SITRANS LR560s.

Page 8 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSpecificationsSpecificationsPowerBus powered 9 to 32 V DC, per IEC 61158-2 (Foundation Fieldbus)Current consumed 13.5 mAPerformanceReference operating conditions according to IEC 60770-1• ambient temperature +15 to +25 oC (+59 to +77 oF)• humidity 45% to 75% relative humidity• ambient pressure 860 to 1060 mbar g (86,000 to 106,000 N/m2 g)Measurement Accuracy1) (measured in accordance with IEC 60770-1)• Maximum measured error Greater of 25 mm (1") or 0.25% of range from minimum detectable distance to full rangeFrequency 78 to 79 GHz FMCWMax. measurement range2)• 40 m version 40 m (131 ft) • 100 m version 100 m (328 ft) Min. detectable distance 300 mm (11.8") from sensor reference pointUpdate time3) Maximum 10 seconds, depending on setting for Response Rate (2.3.6.1.)Influence of ambient temperature <0.003%/K (average over full temperature range, referenced to maximum range)Dielectric constant of material measured• Minimum dK = 1.6 for ranges to 20 m (65.6 ft) range= 2.5 for ranges to 100 m (328 ft) rangeMemory• non-volatile EEPROM• no battery requiredNotes:• Siemens Milltronics makes every attempt to ensure the accuracy of these specifications but reserves the right to change them at any time. 1) Reference conditions: Position Detect (2.4.5.2.) set to Center and Algorithm (2.4.5.1.) set to True First Echo. 2) From sensor reference point.3) Reference conditions: Response Rate (2.3.6.1.) set to FAST.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 9mmmmmSpecificationsInterfaceCommunication• Foundation Fieldbus• ITK version 5 Blocks supported: RESOURCE, LTB, AIFB1, AIFB2, PID, LCD, DIAGBlock execution time: AIFB - 30 ms, PID - 100 msConfiguration• remote FF host system or Emerson AMS version 9.0 (PC)• local Siemens Milltronics infrared handheld programmer [seeProgrammer (infrared keypad) on page 11], or Field Communicator 375 [see Field Communicator 375 (FC375) on page 147], or local control buttonsOptional removablelocal display interface (LDI)1) graphic LCD, with bar graph representing levelMechanicalProcess Connections:• universal flat-faced flanges2) 3"/80 mm, 4"/100 mm, 6"/150 mm- materials stainless steel 316L (1.4404 or 1.4435), or 304• Aimer flanges2) 3"/80 mm, 4"/100 mm, 6"/150 mm- material polyurethane powder-coated cast aluminumEnclosure • construction 316L/1.4404 stainless steel• conduit entry M20x1.5, or ½" NPT • conduit entry connector M12 connector (shipped with M20 to M12 adaptor) (optional) or 7/8" connector (shipped with 1/2" NPT to 7/8" adaptor)• ingress protection Type 4X/NEMA 4X, Type 6/NEMA 6, IP68• lid with window polycarbonate (window material)Lens antenna material•construction - 40 m version PEI - 100 m version PEEK1) Display quality will be degraded in temperatures below –20 °C (–4 °F) and above +65°C (+149 °F).2) Universal flange mates with EN 1092-1 (PN16)/ASME B16.5 (150 lb)/JIS 2220 (10K) bolt hole pattern.

Page 10 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSpecificationsAir Purge Connection• equipped with female 1/8" NPT fittingWeight• 3" stainless steel flange model 3.15 kg (6.94 lb)Environmental• location indoor/ outdoor• altitude 5000 m (16,404 ft) max.• ambient temperature −40 to +80 °C (−40 to +176 °F)• relative humidity suitable for outdoor Type 4, 4X/NEMA 4, 4X, Type 6/NEMA 6, IP68 enclosure (see note above)• installation category I• pollution degree 4Process• temperature and pressure1)Approvals •General CSAUS/C, FM, CE• Radio R&TTE (Europe), FCC, Industry Canada, C-TICKNote: Use appropriate conduit seals to maintain IP or NEMA rating.Versions Stainless steel flangeAimer flange 0.5 bar max.Aimer flange 3.0 bar max40 m –40 to +100 °C (–40 to +212 °F)–40 to +100 °C(–40 to +212 °F)–40 to +100 °C(–40 to +212 °F)100 m –40 to +200 °C(–40 to +392 °F)–40 to +200 °C(–40 to +392 °F)–40 to +120 °C(–40 to +248 °F)1) Maximum and minimum process temperatures are dependent on the process con-nection, O-ring materials, and vessel pressure. Use of the Easy Aimer limits maximum temperature.Note: The device nameplate lists the approvals that apply to your device.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 11mmmmmSpecifications• Hazardous Non-sparking/ Energy Limited1) (Europe) ATEX II 3G Ex nA/nL IIC T4 Gc Dust Ignition Proof 1) (Europe/International) ATEX II 1D, 1/2D, 2D IECEx SIR 09.0149X Ex tD A20 IP67 T100 oC Dust Ignition Proof 2) (US/Canada) FM/CSA: Class II, Div. 1, Groups E, F, G Class III T4 Non-incendive 2) (US/Canada) FM/CSA Class I, Div. 2, Groups A, B, C, D, T4Programmer (infrared keypad)Siemens Milltronics Infrared IS (Intrinsically Safe) Hand Programmer for hazardous and all other locations (battery is non-replaceable) • approval FM/CSA Class I, II, III, Div. 1, Gr. A to G T6CEATEX II 1GD Ex ia IIC T4 Ga Ex iaD 20 T135 °C IECEx SIR 09.0073 Ex ia IIC T4 Ga Ex iaD 20 T135 °C INMETRO Br-Ex ia IIC T4• ambient temperature −20 to +50 °C (−5 to +122 °F)• interface proprietary infrared pulse signal• power 3 V lithium battery • weight 150 g (0.3 lb)• color black• Part Number 7ML1930-1BK1) See Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/International) on page 28 for more details.2) See Non-incendive and Dust Ignition Proof wiring (US/Canada) on page 28Notes: • Battery is non-replaceable with a lifetime expectancy of 10 years in normal use. • To estimate the lifetime expectancy, check the nameplate on the back for the serial number. The first six numbers show the production date (mmddyy), for example, serial number 032608101V.

Page 12 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSpecificationsDimensions SITRANS LR560 with stainless steel universal flat flange1)Notes: • Process temperature and pressure capabilities are dependent upon information displayed on the process device markings.• Refer to Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.1) Shipped with product, packed in a separate bag.grounding lugpurge inletprocess connection: flat flangecable gland1) 110 mm (4.33")176 mm (6.93")9.6 mm (0.38")lid locksensor reference point3": 200 mm (7.87")4": 229 mm (9.02")6": 285 mm (11.22")pressure-related informationdevice label

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 13mmmmmSpecificationsSITRANS LR560 with 3" Aimer FlangeNotes: • Process temperature and pressure capabilities are dependent upon information displayed on the process device markings.• Refer to Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.grounding lugpurge inletprocess connection: aimer flangecable gland110 mm (4.33")166.1 mm (6.54")200 mm (7.87")23.3 mm (0.92")sensor reference pointlid lockpressure-related informationdevice label

Page 14 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSpecificationsSITRANS LR560 with 4" and 6" Aimer FlangeC SpannerNotes: • Process temperature and pressure capabilities are dependent upon information displayed on the process device markings.• Refer to Universal Slotted Flange on page 16 for bolt hole pattern and dimensions.grounding lugpurge inletprocess connection: aimer flangecable gland110 mm (4.33")166.1 mm (6.54")sensor reference point9.6 mm (0.38")4": 229 mm (9.02")6": 285 mm (11.22")4": 53.2 mm (2.09")6": 60.0 mm (2.36)pressure-related informationlid lockdevice labelA C spanner, used to loosen the aimer locking ring, is shipped with the device.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 15mmmmmSpecificationsProcess Connection Label (Pressure Rated Versions)For pressure-rated versions only, the process connection label lists the following information:Item Sample Text Comments/ExplanationCONNECTION SERIES ASME B16.5 / EN 1092-1 / JIS B 2220Flange Series: dimensional pattern based on ASME B16.5/EN 1092-1/JIS B 2220 flange standardsNOM. PIPE SIZE (DN) 4 INCH / 100mm Nominal Pipe Size: based on 150#/PN16/10K flange pressure classesMAWP (PS) 3BAR Maximum Allowable Working Pressure at Design TemperatureDESIGN TEMP. (TS) 100 ºC Maximum Allowable Working TemperatureMIN. PROCESS 3BAR AT -40 ºC Minimum Wetted Process Conditions0F13589.5 Canadian Registration Number (CRN)TEST PRESSURE (PT) 5.2 BAR Production Test PressureTEST DATE 10/01/04 Date of Pressure Test (Year/Month/Day)PROCESS SERIES 25785 Pressure Tag Family SeriesWETTED NON-METALLIC PEI Sensor Lens MaterialWETTED METALLICS 304L Process Connection Material(s)WETTED SEALS FKM / VQM Seal Material(s)

Page 16 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmSpecificationsUniversal Slotted FlangeSlotted Flange Dimensions and Aimer1)WARNING: The user is responsible for the selection of bolting and gasket materials which will fall within the limits of the flange and its intended use and which are suitable for the service conditions.Pipe SizeFlange O.D.Thick-ness (s)Bolt Hole Circle Max ØBolt Hole Circle Min ØBolt Hole radiusNo. of Slotted Holes3" or 80 mm7.87"(200 mm)0.38" (9.65 mm)6.30" (160 mm)5.91" (150 mm)0.38" (9.65 mm)84" or 100 mm9.00"(229 mm)0.38" (9.65 mm)7.52" (191 mm)6.89" (175 mm)0.38" (9.65 mm)86" or 150 mm 11.22"(285 mm)0.38" (9.65 mm)9.53" (242 mm)9.45" (240 mm)0.45" (11.5 mm)81) Universal flange mates with EN 1092-1 (PN16)/ASME B16.5 (150 lb)/JIS 2220 (10K) bolt hole pattern.bolt hole circle max. diameterslotted bolt holesection A-Athicknessbolt hole radiusbolt hole circle min. diameterflange O.D.45 °

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 17mmmmmInstallationInstallationPressure Equipment Directive, PED, 97/23/ECSITRANS LR560 Radar Level Measurement instrument falls below the limits of Article 3, sections 1 & 2 of the Pressure Equipment Directive (PED, 97/23/EC) as a category I pres-sure accessory. However, in accordance with PED, 97/23/EC, Article 3, section 3, this equipment has been designed and manufactured in accordance with Sound Engineering Practice (SEP) (see EU Commission Guideline 1/5).WARNINGS: • Installation shall be performed only by qualified personnel and in accordance with local governing regulations.• SITRANS LR560 is to be used only in the manner outlined in this manual, otherwise protection provided by the device may be impaired.• Never attempt to loosen, remove, or disassemble process connection or instrument housing while vessel contents are under pressure.• The user is responsible for the selection of bolting and gasket materials which will fall within the limits of the flange and its intended use and which are suitable for the service conditions.• Improper installation may result in loss of process pressure.Notes:• For European Union and member countries, installation must be according to ETSI EN 302372.• Refer to the device nameplate for approval information.• Pressure rated versions of the SITRANS LR560 are pressure tested, meeting or exceeding the requirements of the ASME Boiler and Pressure Vessel Code and the European Pressure Equipment Directive.• The serial numbers stamped in each process connection body provide a unique identification number indicating date of manufacture.Example: MMDDYY – XXX (where MM = month, DD = day, YY = year, and XXX= sequential unit produced) Further markings (space permitting) indicate flange configuration, size, pressure class, material, and material heat code.

Page 18 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML1998KL01mmmmmInstallationMounting locationNozzle locationBeam angle• Beam angle is the width of the cone where the energy density is half of the peak energy density• Peak energy density is directly in front of and in line with the antenna.• Signal is transmitted outside the beam angle; therefore false targets may be detected.Emission cone• Keep emission cone free of interference from ladders, pipes, I-beams or filling streams. • Avoid central locations on tall, narrow vessels.• LR560 uses circular polarization. Rotation of device is not required to optimize signal.Environment• Provide easy access for viewing the display and programming via the handheld programmer.• Provide an environment suitable to the ambient temperature rating.• Use a sunshield if the instrument will be mounted in direct sunlight.Notes: • Correct location is key to a successful application.• Avoid reflective interference from vessel walls and obstructions by following the guidelines below.Notes: • For details on avoiding false echoes, see Auto False Echo Suppression (2.4.8.1.) on page 142.emission conemin. 1 m (39")4°ambient temperature –40 °C to +80 °C (–40 °F to +176 °F)process temperature–40 to +100 °C (–40 to +212 °F) or –40 to +200 °C (–40 to +392 °F) (version dependent)

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 19mmmmmInstallationSunshieldThe LR560 display can be protected by an optional sunshield if the instrument will be mounted in direct sunlight.Aimer Adjustment3" flange 4 and 6" flangeNote: Aiming will assist in measuring material in the cone.12310°5°

Page 20 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML1998KL01mmmmmInstallation1) For 4" and 6" Aimer: loosen the set screws in the locking ring. Holding the electronics enclosure firmly, loosen the Aimer locking ring using the C spanner supplied, until the LR560 drops down slightly. The enclosure can then be turned freely.2) Direct SITRANS LR560 so the antenna is pointed at an angle perpendicular to the material surface, if possible. 3) When the desired position is reached, re-tighten the locking ring using the C spanner, and tighten set screws.4) For the 3" Aimer flange, tapered split washers with pressure rated versions are provided to keep nuts and bolts perpendicular to the flange surface.Air Purging SystemFor convenient cleaning, a purging inlet is provided above the antenna. The system pro-vides an 1/8" inlet (female thread) above the antenna where clean, dry air passes to the face of the antenna lens to clean it. The customer will supply the purging air by a manual or automatic valve system.Notes: • Purge duration, pressure, and interval, will vary with each application. It is the user’s responsibility to determine the requirements depending on the application and cleaning required.• Short duration bursts of high pressure provide more effective cleaning than continuous low pressure air.• It is the customer’s responsibility to ensure that any vacuum or pressure in the measured vessel is maintained, considering the hole that passes through the process connection and SITRANS LR560 antenna system.Aiming is not required for signal optimization with 78 GHz frequency.Aiming will assist in measuring material in the cone.Aimer

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 21mmmmmInstallationPurge Connection• The purge connection is closed by the manufacturer, using a 1/8" plug. • When the plug is removed to connect a purging system, the operator is responsible for ensuring that the purging circuit conforms to "Ex" requirements: for example, by fitting an NRV valve. 1) Purge airflow• The purge airflow is designed to create a strong vortex of air that rapidly cleans the face of the lens. • The air purge system can clean both dust and moisture off the lens. • It can be used for periodic cleaning. Air Consumption (Flow rate versus applied pressure)Air Pressure (psi) Approx. inlet volume flow rate (SCFM)a)20 540 1050 1580 20100 25110 30Recommended 90 to 110 psi for effective cleaning..a) SCFM (standard cubic feet/minute) referenced to 14.7 psia, +68 °F and 36% rel-ative humidity (RH).1) Air pressure in vessel can affect purge operation. purged process connection with factory-installed 1/8" NPT plugangled holes direct air flow

Page 22 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML1998KL01mmmmmInstallationRemovable Display• The optional display can be rotated as required, to one of 4 positions, 90 degrees apart (see Connecting SITRANS LR560 on page 23 for instructions). • It can also be used to transfer parameters from one device to another (see Copy Parameters to Display1.3. on page 88.)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 23WiringWiringPower Connecting SITRANS LR5601) Loosen locking screw.2) Remove LR560 lid. 3) Remove optional display by gently turning the display a quarter turn counter-clockwise until it is free.4) Strip the cable jacket for approximately 70 mm (2.75") from the end of the shielded fieldbus cable, and thread the wires through the gland1).WARNINGS:The DC input terminals shall be supplied from a source providing electrical isolation between the input and output, in order to meet the applicable safety requirements of IEC 61010-1.All field wiring must have insulation suitable for rated voltages. WARNINGS: • Check the device label on your instrument, to verify the approval rating.• Use appropriate conduit seals to maintain IP or NEMA rating.•Read Wiring Setups for hazardous area installations on page 26.Notes: • Separate cables and conduits may be required to conform to standard instrumentation wiring practices or electrical codes.• The optional display can be rotated as required, to 1 of 4 positions at 90 degree intervals. 1) If cable is routed through conduit, use only approved suitable-size hubs for waterproof applications.1.2.3. ¼ turn

Page 24 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01Wiring5) Connect the wires to the terminals as shown (SITRANS LR560 FF is not polarity-sensitive).1) 2)6) Ground the instrument according to local regulations.7) Tighten the gland to form a good seal.8) Replace optional display. .9) After programming and device configuration, secure the locking screw and replace device lid.1) May be shipped with the device.2) The instrument shield connection is internally connected to the external ground lug.Notes: • Foundation Fieldbus (HI) must be terminated at both extreme ends of the cable for it to work properly.• Please refer to the Foundation Fieldbus System Engineering Guidelines (AG-181) Revision 2.0, available from www.fieldbus.org, for information on installing FF (H1) devices.cable gland1) (or NPT cable entry)cable shieldinstrument shield connection2)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 25WiringBasic Configuration with Foundation Fieldbus (H1)controllerRosemount 3420 HSE/H1 GatewayDeltaV and/or AMSLR560 FF LR560 FFPC/laptopFF (H1)Configuration via GatewayFF (HSE)FC375 FC375controllerHSE/H1 Linking DeviceNI-FBUS ConfiguratorLR560 FF LR560 FFPC/laptopFF (H1)Configuration via Linking DeviceFF (HSE)FC375FC375

Page 26 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01WiringWiring Setups for hazardous area installations The following wiring options are available for hazardous area installations:•Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/International) on page 28•Non-incendive and Dust Ignition Proof wiring (US/Canada) on page 28In all cases, check the nameplate on your instrument, and confirm the approval rating.Configuration with Foundation Fieldbus for hazardous areasH1 InterfaceLR560 FF LR560 FFPC/laptopFF (H1)Configuration via PCI/PCMCIA CardPCI/PCMCIA busFC375 FC375NI-FBUS ConfiguratorHazardous AreaNon-hazardous AreacontrollerHSE/H1 GatewayDeltaV and/or AMSLR560 FF LR560 FFPC/laptopFF (H1)Configuration via GatewayFF (HSE)FC375 FC375

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 27WiringConfiguration for hazardous areas (continued)Hazardous AreaNon-hazardous AreacontrollerHSE/H1 Linking DeviceAMS or NI-FBUS ConfiguratorLR560 FF LR560 FFPC/laptopFF (H1)Configuration via Linking DeviceHazardous AreaNon-hazardous Area H1 InterfaceNI-FBUSConfiguratorLR560 FF LR560 FFPC/laptopFF (H1)Configuration via PCI/PCMCIA CardFF (HSE)PCI/PCMCIA busFC375 FC375FC375 FC375

Page 28 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01Wiring1. Non-Sparking/Energy Limited wiring (Europe) and Dust Ignition Proof wiring (Europe/International)• For power demands see Temperature De-Rating on page 146. • For wiring requirements follow local regulations.•See also Instructions specific to hazardous area installations on page 29.2. Non-incendive and Dust Ignition Proof wiring (US/Canada)• For power demands see Temperature De-Rating on page 146.The ATEX certificate listed on the nameplate can be downloaded from the product page of our website at: www.siemens.com/LR560. Go to Support > Approvals/Certificates.The IECEx certificate listed on the nameplate can be viewed on the IECEx website. Go to: http://iecex.iec.ch and click on Ex Equipment Certificates of Conformity then enter the certificate number IECEx SIR 09.0149X. Device label (ATEX/IECEx/C-TICK)FM/CSA Class 1, Div 2 installation drawing number A5E02795836.can be downloaded from the product page of our website at: www.siemens.com/LR560 under Support.Device label (FM/CSA)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 29WiringInstructions specific to hazardous area installations(Reference European ATEX Directive 94/9/EC, Annex II, 1.0.6)The following instructions apply to equipment covered by certificate numbers Sira 09ATEX9356X and Sira 09ATEX4357X:1) For use and assembly and details of marking/coding, refer to the main instructions.2) The equipment is certified for use as Category 1D, 1/2D and 2D equipment per certificate Sira 09ATEX9356X and may be used in hazardous zones 20, 21 and 22. The equipment is also certified for use as Category 3G equipment per certificate Sira 09ATEX4357X and may be used in hazardous zone 2. 3) This equipment has a maximum surface temperature of 139 °C (in an 80 °C ambient). Refer to the applicable code of practice for selection of this equipment with respect to specific dust ignition temperatures.4) The equipment is certified for use in an ambient temperature range of –40 °C to 80 °C.5) The equipment has not been assessed as a safety related device (as referred to by Directive 94/9/EC Annex II, clause 1.5).6) Installation and inspection of this equipment shall be carried out by suitably trained and authorized personnel in accordance with the applicable code of practice.7) The equipment shall be installed such that the supply cable is protected from mechanical damage. The cable shall not be subjected to tension or torque. The equipment manufacturer is not responsible for providing the supply cable. 8) Repair of this equipment shall be carried out by suitably trained and authorized personnel in accordance with the applicable code of practice.Special Conditions for Safe Use The ‘X’ suffix to the certificate number relates to the following special condition(s) for safe use:• Parts of the enclosure may be non-conducting and may generate an ignition-capable level of electrostatic charge under certain extreme conditions. The user should ensure that the equipment is not installed in a location where it may be subjected to external conditions (such as high-pressure steam), which might cause a build-up of electrostatic charge on non-conducting surfaces.• The end user must ensure that an ingress protection of at least IP65 is maintained at each entry to the enclosure by use of a blanking element or cable entry device that meets the requirements of the protection concepts type ‘n’ or increased safety ‘e’ or flameproof ‘d’.• The supply to the equipment shall be rated for a prospective short-circuit current of not more than 10 kA and shall be protected by a suitably-rated fuseNote: Installation shall be performed only by qualified personnel and in accordance with local governing regulations.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 31mmmmmQuick Start: localThe LCD DisplayMeasurement modeNormal operation 1) 2)Fault presentProgram modeNavigation view• A visible menu bar indicates the menu list is too long to display all items.• The depth of the item band on the menu bar indicates the length of the menu list: a deeper band indicates fewer items.• The position of the item band indicates the approximate position of the current item in the list. A band halfway down the menu bar indicates the current item is halfway down the list. 1) Press UP or DOWN arrow to switch.2) In response to a key press request. For details, see Key functions in Measurement mode on page 32.M[]FB 121.40 °CNO DATA EXCH.18.91678134251 – toggle indicator1) to switch between AIFB 1/AIFB 2 (displayed as FB1/FB2)2 – identifies which block is source of displayed value3 – measured value (level, distance)4 – units5 – bar graph indicates level6 – secondary region indicates on request2) electronics temperature, echo confidence, or distance7 – text area displays status messages 8 – device status indicator7 – text area displays a fault code and an error message8 – service required icon appearsS: 0 LOEcurrent item numbercurrent itemcurrent menu item bandmenu bar parameter value/selectionparameter nameParameter view Edit viewparameter number

Page 32 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmQuick Start: localHandheld Programmer Key functions in Measurement modeProgramming SITRANS LR560Change parameter settings and set operating conditions to suit your specific application. (For remote operation see Operating via AMS Device Manager on page 41.)Key Function Displays internal enclosure temperature reading. New value is displayed in LCD secondary region.Displays echo confidence value2).Displays distance measure-ment. New value is displayed in LCD secondary regionMode opens PROGRAM mode.Opens the menu level last displayed in this power cycle, unless power has been cycled since exiting PROGRAM mode or more than 10 minutes have elapsed since PROGRAM mode was used. Then top level menu will be displayed.RIGHT arrowopens PROGRAM mode. Opens the top level menu. UP or DOWN arrowtoggles between AIFB 1 and AIFB 2.Identifies which AIFB is the source of the displayed value.Notes: • While the device is in PROGRAM mode the output remains active and continues to respond to changes in the device.• SITRANS LR560 automatically returns to Measurement mode after a period of inactivity in PROGRAM mode (between 15 seconds and 10 minutes, depending on the menu level). C(Part No. 7ML1930-1BK)The programmer is ordered separately.

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 33mmmmmQuick Start: localParameter menusParameters are identified by name and organized into function groups, then arranged in a 5-level menu structure (seeLCD menu structure on page 155).1. Enter PROGRAM mode• Point the programmer at the display from a maximum distance of 300 mm (1 ft).•RIGHT arrow activates PROGRAM mode and opens menu level 1. •Mode opens the menu level last displayed in PROGRAM mode within the last 10 minutes, or menu level 1 if power has been cycled since then.2. Navigating: key functions in Navigation modeNote: For the complete list of parameters see Parameter Reference on page 86.Notes: • In Navigation mode, ARROW keys move to the next menu item in the direction of the arrow.• For Quick Access to parameters via the handheld programmer, press Home , and then enter the menu number. For example, to access parameter Temperature Units (2.3.3.), press 2.3.3. 1. QUICK START2. SETUP2.1. IDENTIFICATION2.2. DEVICE..................2.5. AIFB 12.5.1. STATIC REV. NO.2.5.2. MODE2.5.3. CHANNEL2.5.4. INPUT SCALING2.5.4. 1. LOWER VALUEdisplayhandheld programmer max. 300 mm(1.0 ft)

Page 34 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmQuick Start: local3. Editing in PROGRAM modeSelecting a listed optiona) Navigate to the desired parameter.b) Press RIGHT arrow to open parameter view.c) Press RIGHT arrow again to open Edit mode. The current selection is highlighted.d) Scroll to a new selection.e) Press RIGHTarrow to accept it. The LCD returns to parameter view and displays the new selection.Changing a numeric valuea) Navigate to the desired parameter.b) Press RIGHT arrow to open parameter view. The current value is displayed.c) Press RIGHT arrow again to open Edit mode. The current value is highlighted.d) Key in a new value.e) Press RIGHT arrow to accept it. The LCD returns to parameter view and displays the new selection.Key Name Menu level Function in Navigation Mode UP or DOWN arrowmenu or parameter Scroll to previous or next menu or parameter.RIGHT arrow menu Go to first parameter in the selected menu, or open next menu.parameter Open Edit mode.LEFTarrow menu or parameter Open parent menu.Mode menu or parameter Change to MEASUREMENT mode.Home menu or parameter Open top level menu: menu 1.parameter namecurrent selectionparameternumbercurrent valueparameter name parameternumber

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 35mmmmmQuick Start: localKey functions in Edit modeTo configure a device via the local user interfaceConfigure the device via the Quick Start Wizard.•See Quick Start Wizard via the LDI push buttons on page 36•See Quick Start Wizard via the handheld programmer on page 36Key Name Function UP or DOWN arrowSelecting options Scrolls to item.Alpha-Numeric editing - Increments or decrements digits- Toggles plus and minus signRIGHT arrowSelecting options- Accepts the data (writes the parameter)- Changes from Edit to Navigation modeNumeric editing - Moves cursor one space to the right- or with cursor on Enter sign, accepts the data and changes from Edit to Navigation modeLEFT arrow Selecting options Cancels Edit mode without changing the parameterNumeric editing - Moves cursor to plus/minus sign if this is the first key pressed- or moves cursor one space to the left.- or with cursor on Enter sign, cancels the entryClear Numeric editing Erases the display.Decimal pointNumeric editing- In Edit mode, enters a decimal point.- In Parameter View, press to store menu path to that parameter, and create custom Secondary Value to be dis-played in secondary region of LCD.Plus or minus signNumeric editing Changes the sign of the entered value. to Numeral Numeric editing Enters the corresponding character.Notes: • Completing the last step of the Quick Start via the local user interface places the RESOURCE block (RES) and Level Transducer Block (LTB) in Automatic mode. • AIFB 1 and AIFB 2 will remain Out of Service (as displayed on the LCD). These blocks can only be configured and scheduled using a network configuration tool. For more details, refer to manual Foundation Fieldbus for Level instruments (7ML19985MP01).

Page 36 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmQuick Start: localQuick Start Wizard via the LDI push buttons1) Press to enter Program mode. 2) Choose Quick Start (1.), and then Quick Start Wizard (1.1.). 3) Follow the steps then choose Finish to save Quick Start parameter changes and return to Program menu, or press to return to Measurement mode.To add or delete digits using the push buttons:1) Navigate to the parameter you wish to modify and press to edit it. The value will be highlighted.2) Press or to delete the highlighted value, or to modify the value from the left-most digit, starting with the plus/minus sign.3) With the plus or minus sign highlighted, press or to change it. Press to highlight the next digit to the right.4) Use or to modify the highlighted digit. Scroll past 9 to reach the decimal point.5) When the value is complete, press until the Enter icon is highlighted , then press to accept the value.To modify a text string:1) Navigate to the parameter you wish to modify and press to edit it. The string will be highlighted.2) Follow the same steps as above, to add, delete, or modify characters.Quick Start Wizard via the handheld programmerNote: When the Enter icon is highlighted, press to insert a digit on the right, to delete the right-most digit, to accept the value, or to cancel.Notes: • Default settings in the Quick Start Wizard are indicated with an asterisk (*) unless explicitly stated.• When using the handheld programmer, the Quick Start wizard settings are inter-related and changes apply only after you select FINISH in Wizard Complete.• Do not use the Quick Start wizard to modify individual parameters: see instead Parameter Reference on page 86. (Perform customization only after the Quick Start has been completed.)

7ML19985LY01 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS Page 37mmmmmQuick Start: local1. Quick Start1.1. Quick Start Wizarda) Point the programmer at the display from a maximum distance of 300 mm (1 ft) and press RIGHT arrow to activate PROGRAM mode and open menu level 1. b) Press RIGHT arrow twice, to navigate to menu item 1.1 and open the Quick Start Wizard. c) At each step, press DOWN arrow to accept default values and move directly to the next item, or RIGHT arrow to open Edit mode: the current selection is highlighted.d) Scroll to desired item and press RIGHT arrow to store the change, then press DOWN arrow to continue.e) At any time you can press UP arrow to go back, or LEFT arrow to cancel and return to Measurement mode.VesselSelect vessel construction material. • Selecting either STEEL or CONCRETE does a functional reset (see Master Reset (4.1.) on page 110).• Selecting STEEL changes the setting for Position Detect (2.4.5.2.) to Rising Edge, and for Algorithm (2.4.5.1.) to F. • Selecting CONCRETE changes the setting for Position Detect (2.4.5.2.) to Rising Edge and for Algorithm (2.4.5.1.) to ALF.Response RateUse a setting just faster than the maximum filling or emptying rate (whichever is greater). Options * STEELCONCRETEResponse Rate Fill Rate/Min (2.3.6.2.)/Empty rate/Min (2.3.6.3.)SLOW 0.1 m/min (0.32 ft/min)MED * 1.0 m/min (3.28 ft/min)FAST 10.0 m/min (32.8 ft/min)Parameter View Edit modeSets the reaction speed of the device to measurement changes in the target range.Selecting SLOW changes setting for Average amount (2.8.3.) to 0.9.

Page 38 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmQuick Start: localUnitsLow Calibration PointHigh Calibration PointWizard CompleteTo transfer Quick Start values to the device and return to Program menu, press DOWN arrow (Finish). Then press LEFT arrow to return to Measurement mode. Options BACK, CANCEL, FINISH (Display returns to 1.1 Quick Start Wizard menu when Quick Start is successfully completed.)Sensor measurement units.Options M, CM, MM, FT, INDefault: MDistance from Sensor Reference Point to Low Calibration Point: usually process empty levelValuesRange: 0.000 to 40.000 m or0.000 to 100.000 mDefault: 100.000 msensor reference point (flange face: see Dimensions on page 12)High Calibration PointLow Calibration PointDistance from Sensor Reference Point to High Calibration Point: usually process full level. ValuesRange: 0.000 to 40.000 m or0.000 to 100.000 mDefault: 0.000 m

Page 40 SITRANS LR560 (FF) – OPERATING INSTRUCTIONS 7ML19985LY01mmmmmQuick Start: localLevel application exampleThe application is a vessel that takes an average 3 hours (180 minutes) to fill and 3 weeks to empty.Fill rate = 0.08 m/minute [(Low Cal Pt. minus High Cal Pt.) / fastest of fill or empty time]= (15.5 m – 1 m) / 180 min. = 14.5 m /180 min. = 0.08 m/min.Therefore SLOW response rate (0.1 m/minute) can be selected. Quick Start Parameter Setting Description Vessel STEELResponse Rate SLOW Resets Fill Rate and Empty Rate to 0.1 m/minute.Units MLow Calibration Point 15.5 Process empty level.High Calibration Point 1.0 Process full level.Wizard Complete FINISH Save new settings and exit WizardSensor Reference Point level Low Calibration PointHigh Calibration Point15.5 m1.0 mSITRANS LR560

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 41mmmmmAMS Device ManagerOperating via AMS Device ManagerAMS Device Manager is a software package used to commission and maintain SITRANS LR560 and other process devices. Please consult the operating instructions or online help for details on using AMS Device Manager version 9.0. (You can find more information at http://www.emersonprocess.com/AMS/.)Functions in AMS Device ManagerAMS Device Manager monitors the process values, alarms and status signals of the device. It allows you to display, compare, adjust, verify, and simulate process device data.Device configuration and monitoring is performed via parameters organized into three function groups:• Configure/Setup• Device Diagnostics•Process VariablesThe way the device handles these parameters is described in terms of a Block Model. See the manual, Foundation Fieldbus for Level instruments (7ML19985MP01), for details.Four blocks have responsibility for handling these parameters: • Level Transducer Block (LTB)• LCD Transducer Block (LCD)• Diagnostic Transducer Block (DIAG)• Resource Block (RES)Within each function group, parameters are associated with a particular Function Block. button access to function groupsactive function group (highlighted)active function block (LTB)active parameter tab parameter dialog window

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 43mmmmmAMS Device ManagerProgramming via AMS Device ManagerNavigating through the parameters• A navigation window on the left-hand side of the screen allows you to navigate through the parameter menu structure (see AMS Menu Structure on page 75.) • Some parameters are accessed from within the dialog window that opens when you click on an icon in the navigation window.• In general, process parameters are accessed through the Level Transducer Block, and device parameters are accessed through the Resource Block.Pull-down menu accessA pull-down menu under Actions provides alternative access to several features.Changing parameter settings1) Modify parameter values in the parameter value field in Configure/Setup view, then click Apply to write the new values to the device. (The Apply button is activated when a parameter is modified.) The parameter field will display in yellow until the value has been written to the device.2) Click OK if you wish to update all parameters and exit to Device Connection View. Click CANCEL to exit without saving changes.Notes: • While the device is in PROGRAM mode the output remains active and continues to respond to changes in the device.• Do not use the handheld programmer at the same time as AMS Device Manager, or erratic operation may result. (To disable operation via the handheld programmer, see Local Operation (6.2.2.) on page 122.)Notes: • For a complete list of parameters accessible via AMS, see AMS Menu Structure on page 75.• For parameters followed by a reference number, additional information is available in Parameter Reference on page 86.Action menu items

Page 44 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerAdding a new deviceElectronic Device Description (EDD)Check the product page of our website at: www.siemens.com/LR560, under Support > Software Downloads, for the latest version of EDD: SITRANS LR560 FF - Foundation Fieldbus - AMS V9.0.1) Check that you have the latest version of the EDD for AMS Device Manager that matches the firmware revision of your device. (See Firmware Revision (2.2.2.) on page 90 to access it via the local user interface). If necessary download the EDD from the product page listed above.2) Save the files to your computer, and extract the zipped file to an easily accessed location. 3) Launch AMS Device Manager – Add Device Type, browse to the unzipped EDD file and select it.4) If desired, enter a new device tag. The device is shipped with a unique tag, consisting of a manufacturer id and serial number1). It is not necessary to change the device tag to make the device operational.To change Device Tag:a) Launch AMS Device Manager – AMS Device Manager.b) From Device Connection View, right click on the FF Network icon and select Rebuild Hierarchy.c) Right click on the device icon, and choose Rename from the menu.d) Enter a device tag and press Enter.Startup1) Launch AMS Device Managera) Launch AMS Device Manager – AMS Device Manager.b) From Device Connection View, right click on the FF Network icon and select Rebuild Hierarchy.c) If you wish to rename the device, right-click on the device icon and select Rename from the menu, enter a new device tag, and click Enter.d) Double-click the device icon. The Configure/Setup menu opens at the device Identification dialog window. At initial startup, the Block Status is Out of Service.Note: SITRANS LR560 requires the EDD for AMS Device Manager version 9.0.1) The device tag is read-only via local operation. Note: The Device Tag described above is distinct from the Tag that describes each block type (located in the Identification folder of each block).

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 45mmmmmAMS Device Manager2) Master Reseta) Navigate to Configure/Setup > Resource Block > Operation and click Methods to open the dialog window.b) In the General field, click Master Reset then click Next to perform a reset to factory defaults. Click Next to accept the default reset to Factory Defaults.c) Click FINISH, then scan the device (see step 3).After a master reset is performed, the device will stop measuring, the Resource and Level Transducer Blocks will go to Out of Service, and the LCD will display the Quick Start Wizard until the device is configured.3) Scan Device Scan Device uploads parameters from the device to AMS Device Manager. This synchronizes parameters between the device and AMS.a) From the menu bar, open the pull-down menu Actions – Scan Device. b) If you are adding a new device, configure the device via the Quick Start wizard.Notes: • We recommend performing a Master Reset before configuring a new device.• RESOURCE and LTB Blocks must be in Out of Service Mode before a Master Reset can be performed.Master Reset

Page 46 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerConfiguring a new deviceConfigure a new device using the Quick Start Wizard. The Quick Start Wizard provides an easy step-by-step procedure that configures the device for a simple application.Please consult the operating instructions or online help for details on using AMS Device Manager.Quick Start Wizard via AMS Device ManagerQuick Start Wizard stepsLaunch AMS Device Manager and double-click the device icon from Device Connection View to open the startup screen.1) Navigate to Configure/Setup > Resource Block > Wizards > Quick Start. • In the navigation window, click on the Quick Start steps in order. • At each step, if you do not wish to change the default values in the dialog window that opens, click on the icon for the next Quick Start step. • If you modify a parameter in any step, the Apply button is activated. Click Apply to write changes to the device. Notes:• The LR560 FF is shipped with RESOURCE and LTB blocks in Out of Service mode. • If you complete the Quick Start Wizard via local operation the first time it is used, it will automatically put the RESOURCE and LTB blocks into AUTO mode. (See Quick Start Wizard via the LDI push buttons on page 36.)• Except for the first time it is used, after completing the Quick Start wizard via local operation, you must manually put the RESOURCE and LTB blocks into AUTO mode.• After completing the Quick Start Wizard via AMS, you must manually put the RESOURCE and LTB blocks into AUTO mode.Notes: • When performing a Quick Start via AMS, the Resource and LTB blocks must be in Out of Service mode before any configuration changes1) can be written. (See Changing Block Modes on page 49.)• After completing the Quick Start wizard via AMS, you must manually place the RESOURCE block in Automatic mode. This will also change LTB to Automatic mode.• Values set using the Quick Start Wizard via AMS are saved and recalled each time it is initiated.1) Changes to parameters that affect the block output.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 47mmmmmAMS Device ManagerStep 1 – IdentificationClick Step 1 - Identification.If you wish to accept the default values, go directly to Step 2 (Descriptor, Message, and Date fields can be left blank). Or if desired, make changes then click Apply. Step 2 – ApplicationClick Step 2 - Application. If you wish to accept the default values, go directly to Step 3.Or select a different vessel type (steel or concrete). [This changes the setting for Position Detect (2.4.5.2.) to Rising Edge.] Then click Apply.Notes: • Selecting either STEEL or CONCRETE does a functional reset (see Master Reset (4.1.) on page 110).• Selecting STEEL changes the setting for Position Detect (2.7.3.3.) to Rising Edge. and for Algorithm (2.7.3.1.) to F.• Selecting CONCRETE changes the setting for Position Detect (2.7.3.3.) to Rising Edge and for Algorithm (2.7.3.1.) to ALF.

Page 48 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerStep 3 – RangesClick Step 3 - Ranges. If you wish to accept the default values, go directly to step 4. Or make changes as desired, then click Apply. Step 4 – SummaryClick Step 4 - Summary. Check parameter settings. Return to individual steps if further changes are necessary. The Quick Start is now complete. Put Resource Block into Automatic Mode (see Changing Block Modes on page 49.)Note: Selecting SLOW Response Rate changes setting for Average amount (2.8.3.) to 0.9.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 49mmmmmAMS Device ManagerChanging Block ModesTo change any block mode follow the same procedure as for changing Resource Block mode.To change Resource Block mode1) Navigate to Configure/Setup > Resource Block > Operation > Block Mode and click Block Mode to open the dialog window.2) Select the desired Target mode and deselect the other option. Click Apply (the Apply button is activated when a change is made).3) Return to the main menu.Configure/Setup ParametersTransducer Block ParametersIdentification and Operation are common to all three Transducer Blocks: Level Transducer Block, LCD Transducer Block, and Diagnostic Transducer Block.Identification (LTB, LCD, DIAG)Navigate to Configure/Setup > LTB and click Identification to open the dialog window for access to:Identification:•TAGRead only. Description for the associated block: device tag prefixed by block type.Note: Resource Block overrides Level Transducer Block. Changing Resource Block mode will also change Level Transducer Block mode.Target Mode deselect edTarget Mode selectedApply

Page 50 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device Manager• Descriptor Text that can be used in any way. Limited to 32 ASCII characters. No specific recommended use. • Transducer Block TypeRead only. Identifies the type of transducer block.• StrategyUsed to identify grouping of blocks.• Plant UnitThe identification number of the plant unit. For example, can be used in the host for sorting alarms.Operation (LTB, LCD, DIAG)Navigate to Configure/Setup > LTB > Operation and click Block Modes to open the dialog window for access to:Block Modes: • Actual Mode (read only)This is the current mode of the block, which may differ from the target based on operating conditions. Its value is calculated as part of the block execution.• Target ModeUsed to request an operating mode.• Permitted ModeDefines the modes that are allowed. The permitted mode is configured based on application requirements.• Normal ModeThis is the mode that the block should be set to during normal operating conditions.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 51mmmmmAMS Device ManagerLevel Transducer Block ParametersOperation (LTB)Navigate to Configure/Setup > LTB > Operation and click Simulation to open the dialog window for access to:Simulation (Input)Allows you to simulate the sensor value which is input to the Level Transducer Block. This tests everything between the Level Transducer Block and Output.• Simulation • Simulation Value1) Set Simulation to Fixed value or Ramp, and click Apply.2) If you select Fixed value, enter a Simulation Value and click Apply.3) Or select Ramp, enter the RAMP start, end, number of steps, and step length, and click Apply.4) After simulation is complete, set Simulation to OFF and click Apply.Notes: • To activate simulation via AMS Device Manager or the 375 Field Communicator, simulation must also be set to Enabled on the device. See Simulate Enable (4.12.) on page 120.• Before enabling or disabling Simulation, put LTB Block into OOS mode (see Changing Block Modes on page 49).• After changes have been made, LTB must be returned to AUTO mode.Ramp start Range: –999999 to 999999. Default: 0 mRamp end Range: –999999 to 999999. Default: 0 mNumber of steps Range: 1 to 65535. Default: 10Step length Range: 1 to 65535. Default: 5 s

Page 52 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerSetup (LTB)Sensor (LTB)Navigate to Configure/Setup > LTB > Setup and click Sensor for access to:General•Unit • Level Units • Temperature Unit • Loss of Echo TimerCalibration • Low Calibration Point • High Calibration Point • Sensor Offset • Low Level Point • High Level Point • Level Offset Rate • Response Rate • Fill Rate per Minute •Empty Rate per MinuteNote: See AMS Menu Structure on page 75 and for parameters followed by a reference number, more detailed descriptions can be found in Parameter Reference on page 86.Note: Selecting SLOW Response Rate changes setting for Average amount (2.8.3.) to 0.9.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 53mmmmmAMS Device ManagerSignal Processing (LTB)GeneralNavigate to Configure/Setup > LTB > Setup > Signal Processing and click on General for access to:Range• Near Range • Far Range • Minimum Sensor Value• Maximum Sensor Value Echo Select• Algorithm •Position Detect• Echo Threshold • CLEF Range•Echo MarkerSampling •Echo Lock • Sampling Up• Sampling Down • Echo Lock Window Echo Quality • Confidence • Echo StrengthFiltering • Narrow Echo Filter• Reform EchoNote: See AMS Menu Structure on page 75 and for parameters followed by a reference number, more detailed descriptions can be found in Parameter Reference on page 86.

Page 54 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerTVT A custom Time Varying Threshold (TVT) allows you to screen out false echoes, for example, in a tank with obstructions. See Auto False Echo Suppression (2.4.8.1.) on page 142 for more information.There are two options: • Auto False Echo Suppression automatically calculates the position of the TVT.• TVT shaper breakpoints allow you to manually modify the TVTTVT (Auto False Echo Suppression)Navigate to Configure/Setup > LTB > Setup > Signal Processing > TVT. TVT SetupClick TVT Setup to access:• Auto False Echo SuppressionFor more details see TVT (Auto False Echo Suppression) Setup (2.4.8.) on page 100.• Auto False Echo Suppression Range• Hover Level • Shaper Mode Allows you to modify breakpoints under the TVT Shaper tabs, and view Manual TVT-Curve.1) Turn Shaper Mode On and turn Auto False Echo Suppression Off.2) Click the appropriate TVT Shaper tab and modify breakpoints as desired. 3) Click Apply.Notes: • We recommend using the Auto False Echo Suppression Wizard. See AFES (Auto False Echo Suppression) Wizard on page 87.• Put LTB Block into OOS Mode before changing settings, then back into AUTO mode to display TVT.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 55mmmmmAMS Device ManagerTVT Shaper 1• Shaper breakpoints 1 to 40TVT Shaper 2• Shaper breakpoints 41 to 80TVT Shaper 3• Shaper breakpoints 81 to 120Manual TVT-Curve Displays the effects of the TVT shaper modifications. (Shaper Mode must be On.)Navigate to Configure/Setup > LTB > Setup > Signal Processing > Manual TVT-Curve.Note: Put LTB Block into OOS Mode before changing settings, then back into AUTO mode to display TVT.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 57mmmmmAMS Device Manager• Click Sensor Replaced to reset Time in Operation to 0 hours• Click Snooze for 1 Year to add a year to the Expected Sensor Lifetime.• Click Apply to write changes to the device.Service Schedule Navigate to Configure/Setup > LTB > Maintenance and Diagnostics > Service Schedule.Service ScheduleClick Service Schedule tab for access to•Service Interval • Time Since Last Service• Time Until Next Service • Activation of Reminders • Reminder 1 before Lifetime (Required)• Reminder 2 before Lifetime (Demanded)• Click on Service Performed to reset Time Since Last Service to 0 hours.• Click Apply to write changes to the device.

Page 58 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerElectronics Temperature • Electronics Temperature Displays the current internal temperature of the device• Minimum Value •Maximum Value Communication (LTB)Navigate to Configure/Setup > LTB > Communication for access to:Communication:• Static Revision No.[see Static Revision Number (2.5.1.) on page 103]

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 59mmmmmAMS Device ManagerConfigure/Setup (Liquid Crystal Display Block-LCD)Identification (LCD)(see Identification (LTB, LCD, DIAG) on page 49):Operation (LCD)(see Operation (LTB, LCD, DIAG) on page 50):Block ModesNavigate to Configure/Setup > LCD > Operation and click Block Modes to open the dialog window for access to:• Actual Mode (read only)• Target Mode• Permitted Mode• Normal ModeSee Block Modes: on page 50 for more detail. To remotely disable updating of the LCD:LCD Transducer Block must be put into Out of Service mode. 1) Select Target Mode Out of Service and deselect Automatic.2) Click Apply.Setup (LCD)Navigate to Configure/Setup > LCD > Setup for access to: Local Display•Language •LCD Contrast • LCD Backlight(continued on next page)

Page 60 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerLocal Display (continued)• Local Operation If local operation is disabled remotely and no communication activity exists for 30 seconds, the parameter is made visible again locally.Communication (LCD)Navigate to Configure/Setup > LCD > Communication for access to: Communication:• Static Revision No.[see Static Revision Number (2.5.1.) on page 103]

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 61mmmmmAMS Device ManagerConfigure/Setup (Diagnostic Transducer Block-DIAG)Identification (DIAG)Navigate to Configure/Setup > DIAG > Identification.Identification (see Identification (LTB, LCD, DIAG) on page 49):Operation (DIAG)Navigate to Configure/Setup > DIAG > Operation. (See Operation (LTB, LCD, DIAG) on page 50.)Communication (DIAG)Navigate to Configure/Setup > DIAG > Communication. Communication:• Static Revision No. [see Static Revision Number (2.5.1.) on page 103]Configure/Setup (Resource Block - RESOURCE)Identification (RESOURCE)Navigate to Configure/Setup > RESOURCE > Identification for access to: Identification•TAG Read only. Description for the associated block: device tag prefixed by block type.• Descriptor• Message • Date (Installation Date)The user entered date on which the device was installed in the system.• StrategyUsed to identify grouping of blocks.• Plant UnitThe identification number of the plant unit. For example, can be used in the host for sorting alarms.Note: Parameters in the Diagnostic Transducer Block used solely by factory personnel.Notes: • For a complete list of parameters accessible via AMS, see AMS Menu Structure on page 75.• For parameters followed by a reference number, additional information is available in Parameter Reference on page 86.

Page 62 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerDevice (read only)• Manufacturer •Product NameThe manufacturer’s product name for this device.• Order NumberThe manufacturer’s order number (MLFB) for this device.•Range ModeMeasuring range of the device.• Serial NumberThe manufacturer’s unique serial number for this device.• Hardware Revision • Firmware Revision •Loader Revision • EDD VersionRevision of the EDD associated with this device.• Date of Manufacturing Wizards (RESOURCE)Navigate to Configure/Setup > RESOURCE > Wizards > Quick Start for access to Quick Start steps (see Quick Start Wizard via AMS Device Manager on page 46 .)Operation (RESOURCE)Navigate to Configure/Setup > RESOURCE > Operation.Click on Block Modes to open the dialog window for access to:Block Modes

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 63mmmmmAMS Device ManagerBlock Modes (continued) [see Block Modes: on page 50]• Actual Mode• Target Mode• Permitted Mode• Normal ModeMethodsClick Methods to open the dialog window for access to:Master Reset1)(continued on next page)NOTE: If the RESOURCE block is set to Out of Service, the LTB, and AIFB blocks are forced to Out of Service also, but the LCD and DIAG blocks remain in Automatic mode.Notes: • RESOURCE and LTB Block Status must be Out of Service before a Master Reset can be performed (see Changing Block Modes on page 49).• The following parameters are not reset by any reset type: Write Protection, Auto False Echo Suppression Range, Learned TVT.• While an FF Object Dictionary Reset is in progress, the Master Reset Parameter View showing PREVIOUS/NEXT/BACK/EDIT options will be displayed. Do not perform an action using the local display interface until the reset is complete1). This could cause a temporary loss of communications.1) FF Object Dictionary reset completes with an automatic power cycle.

Page 64 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerMaster Reset (continued)1) Click the Master Reset button, then click Next to perform a reset.2) Select the Reset Type:RESET TYPE RESULT Factory Defaultsa)a) The only difference between Factory Defaults and Functional reset is that Fac-tory Defaults resets maintenance parameters, such as device and sensor wear, calibration and maintenance timers. Functional reset does not reset these parameters.Default. Resets all user parameters to the manufacturer’s default settings. Following this type of reset, complete reprogramming is required.Standard DefaultsResets all parameters to standard default settings.Informational Resets parameters such as Block Descriptor, Strategy, Device Install Date, Device Message.Functionala) Resets parameters that control device behavior and functionality (such as Low Calibration Point).Warm Start Has the same effect as recycling power to the device.FF Object Dictionaryb)b) FF Object Dictionary reset completes with an automatic power cycle.Resets all user parameters except for calibration to Factory Defaults. This option also clears any function block parameters and device schedulec) set by the user.c) See the manual Foundation Fieldbus for Level instruments (7ML19985MP01), Data Transmission, for more details.Master Reset

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 65mmmmmAMS Device Manager3) Click Next, then FINISH to complete the Master Reset.After a master reset is performed, the device will stop measuring, the Resource and Level Transducer Blocks will go to Out of Service, and the LCD will display the Quick Start Wizard until the device is configured.Maintenance & Diagnostics (RESOURCE)Navigate to Configure/Setup > RESOURCE > Maintenance & Diagnostics for access to: Remaining Device Lifetime • Lifetime (Expected) • Remaining Lifetime (read only) • Time in Operation (read only) • Activation of Reminders • Reminder 1 before Lifetime (Required) • Reminder 2 before Lifetime (Demanded) 1) Open the window Remaining Device Lifetime2) After modifying values/units as required, click Apply to accept the change.3) Click on Snooze for 1 Year to add a year to the Total Expected Device Life

Page 66 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerCalibration Schedule • Calibration Interval • Time Since Last Calibration • Time Until Next Calibration • Activation of Reminders • Reminder 1 before Calibration (Required) • Reminder 2 before Calibration (Demanded) Click on Calibration Performed to reset Time Since Last Calibration to 0 hours. Click Apply to accept the change.Wear • Powered Days (read only) • Power-on resets (read only)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 67mmmmmAMS Device ManagerCommunication (RESOURCE)Navigate to Configure/Setup > RESOURCE > Communication to read the following: • Manufacturer • Device TypeManufacturer’s model number associated with the device• Device Revision •DD Revision Revision of the DD (also called EDD) associated with this device.•ITK Version • Static Revision No.[see Static Revision Number (2.5.1.) on page 103]Security (RESOURCE)Navigate to Configure/Setup > RESOURCE > Security to access:Security• Write Protection[see Security (continued) on page 68]See also Password Protection on page 74.(continued on next page)

Page 68 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerSecurity (continued)Device Diagnostics (Level Transducer Block - LTB)Alarms & Errors (LTB)Navigate to Device Diagnostics > LTB > Alarms & Errors.Block ErrorClick on Block Error to open the dialog window to read the following:Failures• Input Failure• Output Failure• Memory Failure• Lost Static Data• Lost Non-Volatile Data•Readback Check• Device Fault State• Block Configuration• Link Configuration• OtherMaintenance• Maintenance Required• Maintenance DemandedInformation• Simulation Active• Local Override• Power Up• Out of ServiceNote: For explanations of the alarms and errors listed below, see Parameter Description charts for the respective block in the manual Foundation Fieldbus for Level instruments (7ML19985MP01).

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 69mmmmmAMS Device ManagerXD Error• Transducer ErrorBlock AlarmClick on Block Alarm to open the dialog window to read the following:Unacknowledged• UnacknowledgedAlarm State•Alarm StateSubcode•SubcodeValue•Value1) From the Block Error tab, check the Maintenance window to display the level of maintenance alarm that is active.2) From the Block Alarm tab, check the Alarm State window to display the level of maintenance alarm that has been acknowledged.3) From the Block Alarm tab, in the Unacknowledged window, select Acknowledged to acknowledge an alert.Note: Acknowledging a maintenance reminder from the device [see Acknowledge (4.2.9.), Acknowledge (4.3.9.), Acknowledge (4.4.9.), Acknowledge (4.5.9.)], will not set the Block Alarm to Acknowledged in AMS. The maintenance alarm will cause an FF block alert, and the block alert can only be acknowledged via a remote host such as NI-FBUS-Configurator or AMS Device Manager (as in step 3 above).

Page 70 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerExtended Diagnostics (LTB)Navigate to Device Diagnostics > LTB > Extended Diagnostics to read the following:Detailed Error Info• Loss of Echo• No Tech Power• Sensor Lifetime Reminder 1• Sensor Lifetime Reminder 2• Service Schedule Reminder 1• Service Schedule Reminder 2• LTB Scale• Internal Temperature Sensor• Internal Temperature High• Internal Temperature Calibration• Velocity Calibration• Transducer Temperature Sensor• Transducer Temperature High• Transducer Temperature LowDevice Diagnostics (Level Control Device Block - LCD)Alarms & Errors (LCD)Navigate to Device Diagnostics > LCD > Alarms & Errors to read Block and Alarm errors. [Errors displayed are the same for each block (LTB, LCD, DIAG, RESOURCE). See Alarms & Errors (LTB) on page 68 for full listing.]Device Diagnostics (Diagnostic Transducer Block - DIAG)Alarms & Errors (DIAG)Navigate to Device Diagnostics > DIAG > Alarms & Errors to read Block and Alarm errors. [Errors displayed are the same for each block (LTB, LCD, DIAG, RESOURCE). See Alarms & Errors (LTB) on page 68 for full listing. See AMS Device Manager instruction manual to work with alarms and errors.]Device Diagnostics (Resource Block - RESOURCE)Alarms & Errors (RESOURCE)Navigate to Device Diagnostics > RESOURCE > Alarms & Errors.Block ErrorClick Block Error tab to read:Failures• Input Failure• Output Failure• Memory FailureFailures

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 71mmmmmAMS Device ManagerFailures (continued)• Lost Static Data• Lost Non-Volatile Data•Readback Check• Device Fault State• Block Configuration• Link Configuration• OtherMaintenance• Maintenance Required• Maintenance DemandedInformation• Simulation Active• Local Override• Power Up• Out of ServiceBlock AlarmClick Block Alarm tab to read:Unacknowledged• UnacknowledgedAlarm State•Alarm StateSubcode•SubcodeValue•ValueWrite AlarmValues available on Block Alarm tab are also available for Write Alarm with one exception: the Value parameter on the Write Alarm tab is a Discrete Value.Alarm SummaryClick on Alarm Summary tab to open the dialog window to read:Current• Discrete Alarm•Block AlarmUnacknowledged• Discrete Alarm Unacknowledged• Block Alarm UnacknowledgedUnreported• Discrete Alarm Unreported•Block Alarm UnreportedDisabled•Write Alarm Disabled•Block Alarm Disabled

Page 72 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerAlarm Summary (continued)Extended Diagnostics (RESOURCE)Navigate to Device Diagnostics > RESOURCE > Extended Diagnostics to read:Detailed Error Info• Device Lifetime Reminder 1• Device Lifetime Reminder 2• Calibration Schedule Reminder 1• Calibration Schedule Reminder 2• Internal Error •External RAM•Memory RAM• Memory EEPROM• Memory EEPROM Flags• Memory Flash• Invalid Loader

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 73mmmmmAMS Device ManagerProcess Variables (Level Transducer Block - LTB)To compare outputs in real time navigate to Process Variables > LTB > Process Variables. ValuesClick Values tab to view:• Primary Variable View a chart showing level value.•Value The primary variable and the channel 1 output from the transducer block as a number.For level applications, chart range is affected by High and Low Level Point values set in Configure/Setup > LTB > Setup > Sensor.Trend View Click Trend View tab to view:• Trend Values• Trend ViewThe primary variable and the channel 1 output from the transducer block.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 75mmmmmAMS Device ManagerAMS Menu Structure Note: Where a parameter number is listed, more information is available for that parameter in Parameter Reference on page 86. Configure/Setup Function Group parameter numberLEVEL TRANSDUCER BLOCKIDENTIFICATIONIdentificationIdentification (tab)TAGDescriptor 2.1.2Transducer Block TypeStrategyPlant UnitOPERATIONBlock ModesBlock Modes (tab)Actual ModeTarget Mode 2.5.2Permitted ModeNormal ModeSimulationSimulation (Input) (tab)Sensor Value SimulationSimulationSimulation valueRAMP startRAMP endRAMP No. of stepRAMP step lengthSETUPSensor 2.3Sensor (tab)GeneralUnit 2.3.1Level Units 2.3.2Temperature Unit 2.3.3Loss of Echo Timer 2.3.4Calibration 2.3.5Low Cal. Point 2.3.5.1High Cal. Point 2.3.5.2Sensor Offset 2.3.5.3

Page 76 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerLEVEL TRANSDUCER BLOCK (CONTINUED)Calibration (continued)Low Level Point 2.3.5.4High Level Point 2.3.5.5Level Offset 2.3.5.6Rate 2.3.6Response Rate 2.3.6.1Fill Rate per Minute 2.3.6.2Empty Rate per Minute 2.3.6.3Signal Processing 2.4GeneralGeneral (tab)RangeNear Range 2.4.1Far Range 2.4.2Min. Sensor Value 2.4.3Max. Sensor Value 2.4.4Echo Select 2.4.5Algorithm 2.4.5.1Position Detect 2.4.5.2Echo Threshold 2.4.5.3CLEF Range 2.4.5.4Echo Marker 2.4.5.5Sampling 2.4.6Echo Lock 2.4.6.1Sampling Up 2.4.6.2Sampling Down 2.4.6.3Echo Lock Window 2.4.6.4Echo Quality 2.4.7Confidence 2.4.7.1Echo Strength 2.4.7.2TVT 2.4.8TVT Setup (tab)Auto False Echo Suppression 2.4.8.1Auto False Echo Suppression Range2.4.8.2Hover Level 2.4.8.3Shaper Mode 2.4.8.4TVT Shaper 1 (tab)2.4.9Breakpoints 1-40TVT Shaper 2 (tab)Breakpoints 41 - 80Configure/Setup Function Group (continued) parameter number

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 77mmmmmAMS Device ManagerLEVEL TRANSDUCER BLOCK (CONTINUED)TVT Shaper 3 (tab)Breakpoint s 81 -120Manual TVT-CurveManual TVT-Diagram (tab)MAINTENANCE & DIAGNOSTICSRemaining Sensor Lifetime 4.3Sensor Lifetime (tab)Lifetime (Expected) 4.3.1Time in Operation 4.3.2Remaining Lifetime 4.3.3Activation of Reminders 4.3.4Reminder 1 before Lifetime (Required) 4.3.5Reminder 2 before Lifetime (Demanded) 4.3.6Service Schedule 4.4Service Schedule (tab)Service Interval 4.4.1Time Since Last Service 4.4.2Time Until Next Service 4.4.3Activation of Reminders 4.4.4Reminder 1 before Service (Required) 4.4.5Reminder 2 before Service (Demanded) 4.4.6Electronics Temperature 3.4Electronics Temperature (tab)Electronics TemperatureMinimum Value 3.4.1Maximum Value 3.4.2COMMUNICATIONCommunicationCommunication (tab)Static Revision No. 2.5.1Configure/Setup Function Group (continued) parameter number

Page 78 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerLCD TRANSDUCER BLOCKIDENTIFICATIONIdentificationIdentification (tab)TAGDescriptor 2.1.2Transducer Block TypeStrategyPlant UnitOPERATIONBlock ModesBlock Modes (tab)Actual ModeTarget ModePermitted ModeNormal ModeSETUPLocal DisplayLocal Display (tab)Language 7LCD Contrast 4.10LCD Backlight 4.9Local OperationCOMMUNICATIONCommunicationCommunication (tab)Static Revision No. 2.5.1DIAGNOSTIC TRANSDUCER BLOCKIDENTIFICATIONIdentificationIdentification (tab)TAGDescriptor 2.1.2Transducer Block TypeStrategyPlant UnitOPERATIONBlock ModesBlock Modes (tab)Actual ModeTarget ModePermitted ModeConfigure/Setup Function Group (continued) parameter number

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 79mmmmmAMS Device ManagerDIAGNOSTIC TRANSDUCER BLOCK (CONTINUED)OPERATION Block Modes (continued)Normal ModeCommunicationCommunication (tab)Static Revision No. 2.5.1RESOURCE BLOCKIDENTIFICATIONIdentificationIdentification (tab)IdentificationTAGDescriptor 2.1.2Message 2.1.3Date 2.1.4StrategyPlant UnitDeviceManufacturer 5.3Product NameOrder NumberRange ModeSerial NumberHardware Revision 2.2.1Firmware Revision 2.2.2Loader Revision 2.2.3EDD VersionDate of Manufacturing 2.2.4WIZARDSQuick StartStep 1 - IdentificationStep 2 - ApplicationStep 3 - RangesStep 4 - SummaryOPERATIONBlock ModesBlock Modes (tab)Actual ModeTarget ModePermitted ModeNormal ModeConfigure/Setup Function Group (continued) parameter number

Page 80 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerMethodsMethods (tab)GeneralMaster Reset 4.1RESOURCE BLOCK (CONTINUED)MAINTENANCE & DIAGNOSTICSRemaining Device Lifetime 4.2Device Lifetime (tab)Lifetime (Expected) 4.2.1Remaining Lifetime 4.2.3Time in Operation 4.2.2Activation of Reminders 4.2.4Reminder 1 before Lifetime (Required) 4.2.5Reminder 2 before Lifetime (Demanded) 4.2.6Calibration Schedule 4.5Calibration Schedule (tab)Calibration Interval 4.5.1Time Since Last Calibration 4.5.2Time Until Next Calibration 4.5.3Activation of Reminders 4.5.4Reminder 1 before Calibration (Required) 4.5.5Reminder 2 before Calibration (Demanded) 4.5.6WearWear (tab)Powered Days 4.6Poweron Resets 4.7COMMUNICATIONCommunicationCommunication (tab)Manufacturer 5.3Device TypeDevice Revision 5.5DD RevisionITK Version 5.6Static Revision No. 2.5.1SECURITYSecuritySecurity (tab)Write ProtectionWrite Protection 6.2.1Configure/Setup Function Group (continued) parameter number

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 81mmmmmAMS Device ManagerDevice Diagnostics Function Group LEVEL TRANSDUCER BLOCKALARMS & ERRORSBlock ErrorBlock Error (tab)FailuresInput FailureOutput FailureMemory FailureLost Static DataLost Non-Volatile DataReadback CheckDevice Fault StateBlock ConfigurationLink ConfigurationOtherMaintenanceMaintenance RequiredMaintenance DemandedInformationSimulation ActiveLocal OverridePower UpOut Of ServiceXD ErrorTransducer ErrorBlock AlarmBlock Alarm (tab)UnacknowledgedAlarm StateSubcodeValueEXTENDED DIAGNOSTICSExtended DiagnosticsExtended Diagnostics (tab)Detailed Error InfoLoss of EchoNo Tech PowerSensor Lifetime Reminder 1Sensor Lifetime Reminder 2Service Schedule Reminder 1Service Schedule Reminder 2LTB ScaleInternal Temp Sensor

Page 82 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerLEVEL TRANSDUCER BLOCK (CONTINUED)Detailed Error Info (continued)Internal Temp HighInternal Temperature CalibrationVelocity CalibrationTransducer Temperature SensorTransducer Temperature HighTransducer Temperature LowLCD TRANSDUCER BLOCK ALARMS & ERRORSBlock ErrorBlock Error (tab)FailuresInput FailureOutput FailureMemory FailureLost Static DataLost Non-Volatile DataReadback CheckDevice Fault StateBlock ConfigurationLink ConfigurationOtherMaintenanceMaintenance RequiredMaintenance DemandedInformationSimulation ActiveLocal OverridePower UpOut Of ServiceXD ErrorTransducer ErrorBlock AlarmBlock Alarm (tab)UnacknowledgedAlarm StateDevice Diagnostics Function Group (continued)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 83mmmmmAMS Device ManagerLCD TRANSDUCER BLOCK (CONTINUED)Block Alarm (tab) continuedSubcodeValueDIAGNOSTIC TRANSDUCER BLOCKALARMS & ERRORSBlock ErrorBlock Error (tab)FailuresInput FailureOutput FailureMemory FailureLost Static DataLost Non-Volatile DataReadback CheckDevice Fault StateBlock ConfigurationLink ConfigurationOtherMaintenanceMaintenance RequiredMaintenance DemandedInformationSimulation ActiveLocal OverridePower UpOut Of ServiceXD ErrorTransducer ErrorBlock AlarmBlock Alarm (tab)UnacknowledgedAlarm StateSubcodeValueRESOURCE BLOCKALARMS & ERRORSBlock ErrorBlock Error (tab)FailuresInput FailureOutput FailureDevice Diagnostics Function Group (continued)

Page 84 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmAMS Device ManagerRESOURCE BLOCK (CONTINUED)Failures (continued)Memory FailureLost Static DataLost Non-Volatile DataReadback CheckDevice Fault StateBlock ConfigurationLink ConfigurationOtherMaintenanceMaintenance RequiredMaintenance DemandedInformationSimulation ActiveLocal OverridePower UpOut Of ServiceBlock AlarmBlock Alarm (tab)UnacknowledgedAlarm StateSubcodeValueWrite AlarmWrite Alarm (tab)UnacknowledgedAlarm StateSubcodeValueAlarm SummaryAlarm Summary (tab)CurrentDiscrete AlarmBlock AlarmUnacknowledgedDiscrete Alarm UnacknowledgedBlock Alarm UnacknowledgedUnreportedDiscrete Alarm UnreportedBlock Alarm UnreportedDevice Diagnostics Function Group (continued)

Page 86 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParametersParameter Reference Parameters are identified by name and organized into function groups. See LCD menu structure on page 155 for a chart. Parameters noted as Read Only in this section of the manual cannot be written via the local user interface, however they may be accessible via other tools. For those accessible via AMS Device Manager, directions are shown in the section Operating via AMS Device Manager on the pages referenced.1. Quick StartWizards provide step-by step procedures to configure the device, filter out false echoes, and upload and download parameters and firmware to the optional display for easy configuration of multiple LR560s.Press RIGHT arrow twice to open the Wizards menu. Select a wizard, press RIGHT arrow to open the first step, and follow the instructions.1.1. Quick Start WizardThe Quick Start wizard provides an easy step-by-step procedure to configure the device for a simple application.•See Quick Start Wizard via the LDI push buttons on page 36.•See Quick Start Wizard via the handheld programmer on page 36.•See Quick Start Wizard via AMS Device Manager on page 46.Notes: • Most parameters are common to both local and remote operation, and are listed below. For a complete list of AMS parameters, see AMS Menu Structure on page 75.• Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated.• To enter Program mode using the device buttons, press . Press to return to Measurement mode. Do not use the handheld programmer or local control buttons at the same time as AMS Device Manager, or erratic operation may result.• For Quick Access to parameters via the handheld programmer, press Home , then enter the menu number, for example: 2.3.5.• In Navigation mode, ARROW keys navigate the menu in the direction of the arrow. • Press RIGHT Arrow to open Edit Mode, or to save a modification.

Page 88 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParametersg) Press DOWN arrow to initiate Learn. A transition screen appears, followed by the message Wizard Complete.h) Press DOWN arrow (Finish) to save AFES parameter changes and return to Program menu, then press LEFT arrow twice to return to Measurement mode.1.3. Copy Parameters to DisplayTransfers parameter settings from a device to the local display interface.PARAM UPLOAD is displayed, then the device returns to Measurement mode.1.4. Copy Parameters from DisplayTransfers parameter settings from the local display interface to a device.PARAM DOWNLOAD is displayed, then the device returns to Measurement mode.1.5. Copy Firmware to DisplayTransfers firmware from a device to the local display interface.SW UPLOAD is displayed, then the device returns to Measurement mode.See Connecting SITRANS LR560 on page 23 for instructions on removing the local display interface.Press RIGHT arrow to Edit.Press DOWN arrow to select Start and RIGHT arrow to begin the transfer.Press RIGHT arrow to Edit.Press DOWN arrow to select Start and RIGHT arrow to begin the transfer.Press RIGHT arrow to Edit.Press DOWN arrow to select Start and RIGHT arrow to begin the transfer.

Page 90 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.2. Device2.2.1. Hardware RevisionRead only. Revision corresponding to the electronics hardware of the Field Device.2.2.2. Firmware RevisionRead only. Revision corresponding to the software or firmware that is embedded in the LR560.2.2.3. Loader RevisionRead only. Revision corresponding to the software used to update the LR560.2.2.4. Manufacture DateRead only. The date of manufacture of the SITRANS LR560. (Local display format: YY-MM-DD hh:mm:ss)2.3. Sensor2.3.1. UnitSensor measurement unit.2.3.2. Level UnitThe engineering unit used for Level. High Level Point corresponds to High Calibration Point (2.3.5.2.) and Low Level Point corresponds to Low Calibration Point (2.3.5.1.).1)2.3.3. Temperature UnitsSelects the engineering unit to be displayed with the value representing temperature.Values m, cm, mm, ft, inDefault: mOptions m, cm, mm, ft, in, %*%1) The point on the sensor from which measurements are referenced (see Dimensions on page 12).Options K, DEGC, DEGF, DEGR*DEG CHigh Level Point(default: 100%)Low Level Point(default: 0%)Level Low Calibration PointHigh Calibration Pointsensor reference point1) (flange face)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 91mmmmmParameters2.3.4. Loss of Echo (LOE) TimerSets the time to elapse since the last valid reading, before a fault code is reported.2.3.5. Calibration2.3.5.1. Low Calibration PointDistance from sensor reference point1) to Low Calibration Point (corresponding to Low Level Point). Unit is defined in Unit (2.3.1.)2.3.5.2. High Calibration PointDistance from sensor reference point1) to High Calibration Point (corresponding to High Level Point). Unit is defined in Unit (2.3.1.).2.3.5.3. Sensor Offset A constant offset (negative or positive) that can be added to the sensor value2) to compensate if the sensor reference point has shifted. (For example, this could result from adding a thicker gasket or reducing the standoff/nozzle height.) The units are defined in Unit (2.3.1.). For more details see How the LTB works: in the manual, Foundation Fieldbus for Level instruments (7ML19985MP01).Note: See Loss of Echo (LOE) Timer (2.3.4.) on page 145 for more detail.Values Range: 0 to 720 sDefault: 100.000 s1) The point on the sensor from which measurements are referenced (see SITRANS LR560 with stainless steel universal flat flange on page 12 and SITRANS LR560 with 3" Aimer Flange on page 13).Values Range: 0.000 to 40.000 m or 0.000 to 100.000 m. Default: 100.00 mRelated parametersUnit (2.3.1.)Far Range (2.4.2.)Values Range: 0.000 to 40.000 m or 0.000 to 100.000 m. Default: 100.00 m2) See Minimum Sensor Value (2.4.3.) for an illustration.Values Range: -999999 to 999999 m. Default: 0.00 mRelated parametersUnit (2.3.1.)

Page 92 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.3.5.4. Low Level PointThe level when the material is at Low Calibration Point. The unit is defined in Level Unit (2.3.2.).2.3.5.5. High Level PointThe level when the material is at High Calibration Point. The unit is defined in Level Unit (2.3.2.). 2.3.5.6. Level OffsetA constant offset that can be added to Level. The unit is defined in Level Unit (2.3.2.).2.3.6. Rate2.3.6.1. Response RateSets the reaction speed of the device to measurement changes.Use a setting just faster than the maximum filling or emptying rate (whichever is faster). Values Range: -999999 to 999999Default: 0%Values Range: -999999 to 999999Default: 100%Values Range: -999999 to 999999Default: 0%Notes: • Changing Response Rate resets Fill Rate/Min (2.3.6.2.), and Empty rate/Min (2.3.6.3.).• Selecting SLOW Response Rate changes setting for Average amount (2.8.3.) to 0.9.Response Rate (2.3.6.1.)Fill Rate/Min (2.3.6.2.)/Empty rate/Min (2.3.6.3.)slow 0.1 m/min (0.32 ft/min)*medium 1.0 m/min (3.28 ft/min)fast 10.0 m/min (32.8 ft/min)

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 93mmmmmParameters2.3.6.2. Fill Rate/MinDefines the maximum rate at which the reported sensor value1) is allowed to increase. Allows you to adjust the SITRANS LR560 response to increases in the actual material level. Fill Rate is automatically updated whenever Response Rate (2.3.6.1.) is altered. Enter a value slightly greater than the maximum vessel-filling rate, in units per minute. 2.3.6.3. Empty rate/MinDefines the maximum rate at which the reported sensor value1)is allowed to decrease. Adjusts the SITRANS LR560 response to decreases in the actual material level. Empty Rate is automatically updated whenever Response Rate (2.3.6.1.) is altered.Enter a value slightly greater than the vessel’s maximum emptying rate, in units per minute.1) The value produced by the echo processing which represents the distance from sen-sor reference point to the target (see Minimum Sensor Value (2.4.3.) on page 95 for an illustration).OptionsRange: 0 to 999 999 m / min.Response Rate (2.3.6.1.) Fill Rate Slow 0.1 m/min (0.32 ft/min)*Medium 1.0 m/min (3.28 ft/min)Fast 10.0 m/min (32.8 ft/min)Related parametersLevel Unit (2.3.2.)OptionsRange: 0 to 999 999 m / min.Response Rate (2.3.6.1.) Empty RateSlow 0.1 m/min (0.32 ft/min)*Medium 1.0 m/min (3.28 ft/min)Fast 10.0 m/min (32.8 ft/min)Related parametersLevel Unit (2.3.2.)

Page 94 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.4. Signal ProcessingIn AMS Device Manager, see the General tab under Signal Processing (LTB) on page 53.2.4.1. Near Range The range in front of the device (measured from the sensor reference point1)) within which any echoes will be ignored. (This is sometimes referred to as "Blanking" or "Dead Zone".)2.4.2. Far Range Allows the material level to drop below Low Calibration Point without generating a Loss of Echo (LOE) state. See CLEF Range (2.4.5.4.) for an illustration.Use this feature if the measured surface can drop below the Low Cal. Point in normal operation. For more detail see Far Range (2.4.2.) on page 143.1) See SITRANS LR560 with stainless steel universal flat flange on page 12.Values Range: Min = 0Max. = 45 m (40 m device) = 105 m (100 m device)Default: 0.278 m (0.91 ft)Related parametersUnit (2.3.1.)Notes: • Far Range can extend beyond the bottom of the vessel.• When Low Calibration is updated, Far Range will be updated to Low Calibration Pt. + 5 m (16.40 ft).Values Range: Min. = 0Max. = 45 m (40 m device) = 105 m (100 m device)Default = Low Calibration Pt. + 5 m (16.40 ft)Related ParametersUnit (2.3.1.)CLEF Range (2.4.5.4.)

Page 96 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.4.5.2. Position DetectDefines where on the echo the distance measurement is determined. (See Position Detect (2.4.5.2.) on page 139 for more detail.)If the vessel bottom is being reported as the level instead of the actual material level (at low level conditions), we recommend setting Position Detect to Hybrid and using it in combination with CLEF Range (2.4.5.4.).2.4.5.3. Echo Threshold Sets the minimum echo confidence that the echo must meet in order to prevent a Loss of Echo condition and the expiration of the LOE timer. When Confidence (2.4.7.1.) exceeds Echo Threshold (2.4.5.3.), the echo is accepted as a valid echo and is evaluated. Use this feature when an incorrect material level is reported. Note: Selecting Steel or Concrete vessel type in the Quick Start wizard changes the setting for Position Detect (2.4.5.2.) to Rising Edge.OptionsRising Edge (yields highest stability on sloped targets)*Center (yields higher accuracy on flat, non-sloped targets)Hybrid (Center and CLEF)CLEF (Constrained Leading Edge Fit)Related parametersCLEF Range (2.4.5.4.)Values Range: 0 to 99Default: 5Related ParametersLoss of Echo (LOE) Timer (2.3.4.)

Page 98 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.4.6. SamplingProvides a method of checking the reliability of a new echo before accepting it as the valid reading, based on numbers of samples above or below the currently selected echo.2.4.6.1. Echo LockSelects the measurement verification process. See Position Detect (2.4.5.2.) on page 139 for more details.For radar applications, Material Agitator is the most often used setting, to avoid agitator blade detection. 2.4.6.2. Sampling Up Specifies the number of consecutive echoes that must appear above the echo currently selected, before the measurement is accepted as valid. 2.4.6.3. Sampling Down Specifies the number of consecutive echoes that must appear below the echo currently selected, before the measurement is accepted as valid. Echo Lock Options0Lock Off (no verification)1Maximum Verification2*Material Agitator3Total LockRelated parametersFill Rate/Min (2.3.6.2.)Empty rate/Min (2.3.6.3.)Sampling Up (2.4.6.2.)Sampling Down (2.4.6.3.)Algorithm (2.4.5.1.)Values Range: 1 to 50Default: 5Values Range: 1 to 50Default: 2Related parametersEcho Lock (2.4.6.1.) If Echo Lock set to any value other than its default (2), then Down Sampling default = 5.

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 99mmmmmParameters2.4.6.4. Echo Lock WindowA “distance window” centered on the echo1) is used to derive the reading. When a new measurement is in the window, the window is re-centered and the reading is calculated.When the value is 0, the window is automatically calculated after each measurement.• For slower Measurement Response values, the window is narrow.• For faster Measurement Response values, the window becomes progressively wider.2.4.7. Echo Quality2.4.7.1. Confidence Read only. Indicates echo reliability: higher values represent better echo quality. The display shows the echo confidence of the last measurement. Echo Threshold (2.4.5.3.) defines the minimum criterion for echo confidence.2.4.7.2. Echo StrengthDisplays the absolute strength (in dB above 1 μV rms) of the echo selected as the measurement echo.1) See Echo Lock (2.4.6.1.) on page 118 for more detail.Values Range: 0 to 45 m (40 m device) or 0 to 105 m (100 m device)Default: 0 mNote: The Echo Lock window is stored as a standard sample, but displayed in sensor units. Any value entered for the Echo Lock window will be rounded to the nearest sample.Values (view only) 0 to 99----Related Parameters Echo Threshold (2.4.5.3.)Values (view only) –20 to 99

Page 102 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.4.8.4. Shaper ModeEnables/disables TVT Shaper (2.4.9.).2.4.9. TVT Shaper Adjusts the TVT (Time Varying Threshold) at a specified range (breakpoint on the TVT). This allows you to reshape the TVT to avoid unwanted echoes. There are 120 breakpoints arranged in 14 groups.To access TVT shaper via AMS Device Manager see TVT Shaper 1 on page 55.To use TVT shaper via local operation:a) Go to Shaper Mode (2.4.8.4.) and select option ON.b) In TVT shaper, go to Shaper 1-9 (2.4.9.1.).c) Open Shaper 1 and enter the TVT Offset value (between –50 and +50 dB).d) Go to the next Shaper point and repeat step (c) till all desired breakpoint values have been entered.2.4.9.1. Shaper 1-92.4.9.2. Shaper 10-182.4.9.3. Shaper 19-272.4.9.4. Shaper 28-362.4.9.5. Shaper 37-452.4.9.6. Shaper 46-542.4.9.7. Shaper 55-632.4.9.8. Shaper 64-722.4.9.9. Shaper 73-812.4.9.10. Shaper 82-902.4.9.11. Shaper 91-992.4.9.12. Shaper 100-1082.4.9.13. Shaper 109-1172.4.9.14. Shaper 118-120Options ON*OFFNotes: •Shaper Mode (2.4.8.4.) must be turned ON in order for TVT shaper breakpoints to be transferred• We recommend using AMS Device Manager to access this feature.• Put LTB Block into OOS Mode before changing settings, then back into AUTO mode to display TVT.Values Range: –50 to +50 dBDefault: 0

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 103mmmmmParameters2.5. AIFB 12.5.1. Static Revision NumberThe revision level of the static data associated with Analog Input Function Block 1. The Static Revision No. is updated whenever a configuration parameter is changed.2.5.2. ModeUsed to request an operating mode from the Analog Input Function Block. It allows you to put SITRANS LR560 into Manual mode (used in conjunction with Simulation) or Out-of-Service mode for maintenance purposes.Manual Mode can be used when simulating output.Notes: • All AIFB parameters are read only via local operation, and not visible to AMS Device Manager. They can be changed only by a remote host such as DeltaV or NI-FBUS-Configurator.• AIFB 1 and AIFB 2 are not active upon initial startup. These blocks will show Out of Service on the LCD at startup. If these blocks are needed for an FF application, use a tool such as DeltaV or NI-FBUS-Configurator to configure and schedule the blocks. See the manual Foundation Fieldbus for Level instruments (7ML19985MP01) for details.• Default settings in the parameter tables are indicated with an asterisk (*) unless explicitly stated.Note: Ensure that Mode is returned to AUTO when simulation or maintenance are completed.Setting Description Output valueAUTO automatic the automatically-recorded measured valueMAN manual a manually-set fixed simulation valueO/S function block disabledthe preset safety value

Page 104 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.5.3. ChannelUsed to select the Transducer Block output. See the manual, Foundation Fieldbus for Level instruments (7ML19985MP01) for more detail.2.5.4. Input ScalingInput scaling should match the XD_scale from the Level Transducer Block. See the manual Foundation Fieldbus for Level instruments (7ML19985MP01) for more detail.2.5.4.1. Lower ValueDefines the operational lower range value of the input value (Process Value Scale) in Level Units. Process Value Scale normalizes the input value to a customer-defined range.2.5.4.2. Upper ValueDefines the operational upper range value of the input value (Process Value Scale) in Level Units. Process Value Scale normalizes the input value to a customer-defined range.Options Reference Point* Level (SV1 - Secondary Value 1) Low Calibration PointDistance (SV2 - Secondary Value 2) sensor reference pointValues Range: -999999 to 999999Default: 0 %Values Range: -999999 to 999999Default: 100 %Low Calibration Point (process empty level)Level (SV1)Distance (SV2)sensor reference point1) High Calibration Point (process full level)Process Value Scale Input (typically 0 to 100%)Output ScaleProvides Output values (Out) to AIFB 1 or AIFB 2

7ML19985LY01 SITRANS LR560 (FF) – INSTRUCTION MANUAL Page 105mmmmmParameters2.5.4.3. UnitEngineering unit to be displayed with the output value.2.5.4.4. Decimal PointRead only. The number of digits to display after the decimal point (fixed to one).2.5.5. Output ScalingScales the Process Variable. The function block parameter OUT SCALE contains the values of the lower limit and upper limit effective range in AIFB 1 units.2.5.5.1. Lower ValueDefines the operational lower range value of the output value in AIFB 1 units.2.5.5.2. Upper ValueDefines the operational upper range value of the output value in AIFB 1 units.2.5.5.3. UnitEngineering unit to be displayed with the output value2.5.5.4. Decimal PointRead only. The number of digits to display after the decimal point (fixed to two).Options m, cm, mm, ft, in, %, Not Used, Unknown, Special*%Values Range: -999999 to 999999Default: 0 %Values Range: -999999 to 999999Default: 100 %Options m, cm, mm, ft, in, %, Not Used, Unknown, Special*%

Page 106 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.5.6. Alarms & Warnings2.5.6.1. High Limit AlarmThe setting for the upper alarm limit in AIFB 1 units. (Corresponds to HI_HI_ALM.)2.5.6.2. High Limit WarningThe setting for the upper warning limit in AIFB 1 units. (Corresponds to HI_ALM.)2.5.6.3. Low Limit WarningThe setting for the lower warning limit in AIFB 1 units. (Corresponds to LO_ALM.)2.5.6.4. Low Limit AlarmThe setting for the lower alarm limit in AIFB 1 units. (Corresponds to LO_LO_ALM.)2.5.6.5. Limit HysteresisHysteresis is used to adjust the sensitivity of the trigger for alarm messages. It is used to compensate when a process variable fluctuates around the same value as a limit. A high level alarm occurs when a value exceeds an upper limit. The alarm’s status remains true until the value drops below the limit minus the alarm hysteresis. The directions are reversed for low limit detection.Enter a value for the hysteresis here, to be used for all warnings and alarms. The units are always %.Options Range: -999999 to 999999Default: – – – – – –Options Range: -999999 to 999999Default: – – – – – –Options Range: -999999 to 999999Default: – – – – – –Options Range: -999999 to 999999Default: – – – – – –Options Range: 0 to 50%Default: 0.50%

$Page 108 SITRANS LR560 (FF) – INSTRUCTION MANUAL 7ML19985LY01mmmmmParameters2.8.2. Reform EchoSmooths jagged peaks in the echo profile. Reforms fragmented echoes into one echo.2.8.3. Average amountThe fraction of the old shot data that is kept for averaging purposes. A higher value will give a smoother profile at the expense of a slower echo profile response.3. Diagnostics3.1. Echo ProfileAllows you to request the current echo profile either via the handheld programmer, the local buttons, or via AMS Device Manager. For more detail see Echo Processing on page 138.(continued on next page)To request a profile via AMS Device Manager:• see Echo Profile on page 56.To request a profile via the handheld programmer or local control buttons: In PROGRAM mode, navigate to Echo Profile (3.1.). (See Requesting an Echo Profile on page 39 for more details.)Values Range: 0 to 255 samples. Default: 0 (reset to 10 after a Quick Start has been completed)0 = OFFgreater = widerRecommended: 5 to 20 samples. Wider is not recommended.Values 0.0 to 1.0Default: 0.75Notes: • LTB Block must be put back to AUTO mode to display Echo Profile.• Selected icon is highlighted.exit icon, selectedexit icon, deselectedexitpan up/downdistance from flange face to targetAlgorithm selection (trueFirst echo)TVT curvematerial levelconfidence valuedistance from Low Calibration Point to vertical cross-hairmeasurezoom in/outpan left/right - selected/highlightedMeasurement Range (0 to 50 m for example purposes)Echo Amplitude (dB)$