Shure orporated UR2 Wireless Transmitter Held to Face User Manual UR en

Shure Incorporated Wireless Transmitter Held to Face UR en

Exhibit D Users Manual per 2 1033 c3

EnglishModel UHF-R™ Wireless User Guide©2004, Shure Incorporated27XX8849A (Rev. 1) Printed in U.S.A.ContentsFeature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2System Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3Receiver Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4Receiver LCD Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Receiver Parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5Automatic Frequency Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7Networking Receivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8Handheld and Bodypack Transmitter Controls and Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Transmitter LCD Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Transmitter Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Transmitter Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Setting Transmitter Gain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10RF Safety Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10Automatic Transmitter Sync. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11Tips for Improved Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13Replacement Parts and Accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2Shure UHF-R WirelessFeature OverviewThe UHF-R™ Wireless Microphone System uses the latest wireless technology, delivers outstanding audio clarity, and is rugged and reliable. It is easy to set up and operate with advanced features for professional installations requiring multiple wireless microphone systems. Frequency Band SelectionShure offers wireless systems in a selection of bands that conform to the different government regulations of specific nations or geo-graphic regions. These regulations help limit radio frequency (RF) interference among different wireless devices and prevent interfer-ence with local public communications channels, such as television and emergency broadcasts.The system’s band and frequency range are identified on the face of the receiver and transmitter. For example, “H4 518–578 MHz.” For information on bands available in your area, consult your local dealer or phone Shure. More information is also available at Shure’s website (www.shure.com).Groups and ChannelsTo transmit audio through a wireless system, the transmitter and receiver must be set to the same radio frequency, or channel. A wide selection of channels allows more microphones to be used at the same time, since each microphone must operate on a different chan-nel. It also provides a greater choice of open channels—those that are free from interference from television broadcasts, electronic devices, or other wireless systems. A group is a selection of compatible channels. Wireless microphones work better together when set to channels in the same group.Automatic Frequency SelectionThe following features scan the RF environment to find the best group and channel settings for a particular installation. •Group Scan—finds the group with the most open channels, then sets all networked receivers to channels in that group.•Channel Scan—finds the first open channel in the currently selected group and sets the receiver to that channel.Follow the steps on page 7 for instructions on using these features.Automatic Transmitter SyncThis feature automatically transfers the group and channel settings from a receiver to a transmitter. You can also program other trans-mitter settings on a receiver and transfer those settings too. See page 11.Interface LockThis feature locks the receiver and transmitters so that users cannot change settings. The transmitter power switch can also be dis-abled so that the transmitter remains on if the power switch is accidently toggled during a performance.Audio Gain StructureThe following settings allow you to adjust audio gain throughout the system:•Sensitivity (bodypack only). A 25 dB range of gain adjustment at the bodypack transmitter input. •Transmitter Gain. A 30dB range of audio gain adjustment within the transmitter (affects audio level at the receiver, as indicated bythe Audio LEDS.)•Output Level. 32 dB of attenuation at the receiver output, plus a mute setting. •Mic/Line switch. –30 dB pad for matching audio levels at the receiver XLR output.NetworkingEach receiver has an RJ-45 port on the back for connecting to other receivers over an Ethernet network. Networking receivers allows you to automatically set channels for all the receivers with a single group scan command. You can also control and monitor all net-worked receivers through the Shure Wireless Workbench PC software.Shure Wireless Workbench SoftwareThe Shure Wireless Workbench software on the supplied CD includes a variety of useful tools for installing and managing multiple wireless systems. Simply install the software on your computer and connect it to a network of receivers to monitor and control receivers and transmitters throughout the network. (See page 8 for more information on networking.)Instructions on using the Wireless Workbench software are available in the online help files after you install the software.
3EnglishSystem ComponentsAll systems include:Handheld Systems Include:쐃Microphone Head (choice of SM58®, SM86, Beta 58A®, Beta 87A™, or Beta 87C™)쐇UR2 handheld transmitter쐋Microphone clip Bodypack Systems Include: Shure’s Wireless Workbench SoftwareUR4S or UR4D Receiver(UR4D pictured)IEC Power Extension CableTransmitter Carrying CaseTwo Antenna Cables2 Antenna hole plugs4 Rack Mount Screws with WashersTwo 1/2 Wave AntennasAA Batteries Ethernet Network Cable with “Ruggedized” plugIEC Power Cable쐃쐇쐋UR1 Bodypack TransmitterThreaded TA4F Adapter
4Shure UHF-R WirelessReceiver Controls and Connectors쐃SYNC Infrared (IR) port. Transmits group, channel, and other settings to a transmitter. See page 11.쐇Squelch LEDs. •Blue (On)=Transmitter signal detected• Off = no signal or signal squelched because of poor receptionor no tonekeyNOTE: The receiver will not output audio unless at least one blue LED is illuminated.쐋RF LEDs. Indicate RF signal strength from the transmitter at each antenna and diversity condition. •Amber=normal• Red = overload (greater than –20 dBm)쐏Audio LEDs. Indicate audio signal strength from transmitter. • Green = signal present• Yellow = normal peak•Red=overloadTo correct this level, adjust the transmitter gain.쐄Indicates the name and range of receiver frequency band.쐂LCD Interface. Provides a convenient way to program the receiver from the front panel (see detail on next page). 쐆Monitor. 1/4” output jack and volume knob for headphones.•Monitor Clip LED indicates headphone audio is clipping.•Dual models: Push the knob to switch from receiver one to re-ceiver two. 쐊Power switch. Powers the unit on and off.쐎AC mains power input, IEC connector. 100–240 Vac.쐅AC mains power passthrough (unswitched). Use with an IEC extension cable to supply AC power to another device.쐈Diversity antenna inputs A and B.쐉Mic/Line switch. Changes output level –30 dB (XLR output only).씈Electrically balanced XLR output jack씉Lift/GND switch. Lifts ground from Pin 1 of the XLR connec-tor (default = GND).씊Impedance balanced 1/4” output jack (200Ω)씋USB jack for computer interface.씌RJ-45 jack for Ethernet network interface. Accepts both regu-lar and “ruggedized” RJ-45 plugs.쐃쐇쐏쐋쐄쐂쐆 쐊쐎쐅 쐈쐉씈씉씊씋씌 쐈
5EnglishReceiver LCD InterfaceReceiver ParametersUse the following instructions to set parameters through the LCD interface.NOTE: After adjusting a parameter, you must press the flashing ENTER button to accept the change.Group and ChannelMenu: Radio•Push the Control wheel to move the cursor to the Group (G)or Channel (Ch) parameter. •Turn the Control wheel to change the parameter.FrequencyMenu: Radio•Push the Control wheel to move the cursor to the integervalue (741.000 MHz) or fractional value (741.025). •Turn the Control wheel to change the value.Automatic Transmitter SyncMenu: Sync• See page 11.Receiver NameMenu: Util•Turn the Control wheel to change the letter.•Push the Control wheel to move to the next letter.Output LevelMenu: AudioThis setting adjusts the signal level at the XLR and 1/4” audio output jacks.•Turn the Control wheel to change the relative level in dB.(0 dB to –32 dB). • Turn the wheel all the way down to mute the outputs.SquelchMenu: Radio > Squelch•Turn the Control wheel to change the parameterReceiver LockWhen locked, the receiver settings cannot be changed from the front panel. However, you can still navigate the LCD menu to view the settings (and turn the lock off).Menu: Util > Lock•Turn the Control wheel to toggle the lock on or off (ON orOFF).LCD ViewMenu: Util > Title•Turn the Control wheel to mark an item for display.•Push the Control wheel to move to the next item.LCD ContrastMenu: Util > Contrast•Turn the Control wheel to increase or decrease contrast.TonekeyMenu: Radio > Squelch > TonekeyTonekey squelch mutes the outputs unless the receiver detects a transmitter. Tonekey should be left on (On) except for certain troubleshooting operations.RadioAudioUtilSHUREG: 3 Ch: 1 Out: -0dB+12 dB+100 mW524-025 MHz TV: 32SyncAccept ChangesAfter changing a parameter, the ENTER button flashes. Press it to save the value.Cursor ControlPush the Control wheel to move the cursor to the next item. Turn the Control wheel to change a parameter value.Exit/CancelPress the Exit button to cancel changes and return to the previous menu.Menu AccessPress the Navigate key next to themenu item you want to select.Transmitter Status DisplayEverything under the dotted line reflects the settings for the transmitter, if present. (main title screen only).
6Shure UHF-R WirelessNetwork ParametersNOTE: • The receiver reboots after you press ENTER to accept net-work parameter changes• In dual models (UR4D), these settings affect both receivers(the dual receiver is treated as a single network device).Set the Receiver Network ModeMenu: Util > Network1.Push the Control wheel to move the cursor to the Mode parameter.2.Turn the Control wheel to set the receiver to one of the following values: •Default: sets the receiver to a unique IP address basedon its MAC address•DHCP: use this setting when connecting the receiver to aDHCP server.•Manual: allows you to set the receiver to a specific IP ad-dress, subnet, or gatewayIP Address, Subnet and GatewayMenu: Util > NetworkNOTE: To change these settings, the network mode must be set to Manual.1.Push the Control wheel to move the cursor to any of the following parameters:•IP (IP address)•Gate (Gateway)•Sub (Subnet mask)2.Turn the Control wheel to change the value.Device IDAssists in identifying receivers through the Wireless Work-bench Software (has no affect on network identification).Menu: Util > Network1.Push the Control wheel to move the cursor to the DevID parameter.2.Turn the Control wheel to set the receiver to change the value. Custom GroupsThis feature allows you to select and create your own groups of frequencies.Selecting existing custom groups...Menu: Radio > Custom•Push the Control wheel to move the cursor to the Groupparameter. •Turn the Control wheel to select a custom group number(C1, C2, C3, etc.)Creating new groups...Menu: Radio > Custom1.Turn the Control wheel to select a custom group number (C1, C2, C3, etc.)2.Push the Control wheel to move to the Channel parameter and turn it to select a channel (01, 02, 03, etc.)3.Push the Control wheel to move to the Freq parameter and select a frequency for that channel.4. Push the NEXT menu key to select a frequency for the next channel in that group.
7EnglishAutomatic Frequency SelectionFollow these steps to use the channel scan and group scan features.Before you begin...• Install the receivers in the location where they will be used and power them on. • Mute all inputs on mixing devices connected to receivers.• Turn off all bodypack or handheld transmitters for the systems you are setting up. •Turn on potential sources of interference such as other wireless systems or devices, computers, CD players, effects processors, anddigital rack equipment so they are operating as they would be during the presentation or performance. Single Receiver1. Select Radio > Scan > Chan Scan using the Navigate keys on the receiver LCD interface. 2.Turn the Control wheel to select a group. 3. Press Chan Scan. The display indicates that the receiver is searching. Once it has finished, it displays the selected channel.4. Press the flashing ENTER button to accept the suggested channel.5. Sync the transmitter (see page 11).Networked or Dual ReceiversWith networked or dual receivers, you can take advantage of the group scan feature to set group and channel settings for all the re-ceivers at the same time. (See page 8 for instructions on networking.)Perform a group scan from any receiver...1. Select Radio > Auto > Grp Scan using the Navigate keys on the receiver LCD interface. The display indicates that the receiver is searching (Scan In Progress). Once it has finished, it displays the group with the most open channels.2. If you wish, turn the Control wheel to change groups. The number of open channels for each group is displayed. 3. Press the flashing ENTER button to set all receivers to open channels in that group.NOTE: The group scan feature only works for receivers in the same frequency band. For example, if you did a group scan on a “H4” band receiver, all “H4” band receivers would be set up, but not “J5” band receivers.Multiple Receivers—Not NetworkedIf your receivers are not networked (or in different bands), the group scan cannot automatically set their group and channel settings. However, you can still take advantage of the group scan feature to find the group with the most open channels and the channel scan feature to find open channels in that group.Find the group with the most open channels...Perform a group scan using the steps for a networked receiver (above). However, make a note of the selected group before pressing the flashing ENTER button to accept it.Set the receivers to open channels in that group...Perform a channel scan on the remaining receivers using the steps for a single receiver (above). Make sure to select the same group for each receiver before performing the channel scan.IMPORTANT: After setting the channel for the first receiver, immediately sync the transmitter for that receiver and leave it on so that the next receiver detects that channel during its channel scan. Otherwise, all the receivers will be set to the same open channel. NOTE: Receivers in different bands (H4, J5, L3, etc.) do not need to be set to the same group.
8Shure UHF-R WirelessNetworking ReceiversBasic NetworkSimply connect the receivers to a network hub, such as an Ethernet switch. No network configuration is required if the receiver is set to the default network setting (Util > Network > Mode = Default).Connecting a PCTo access receivers with the Wireless Workbench software, connect the PC to the USB port of any of the receivers in the network.Connecting a PC Using EthernetFor some installations, you may wish to connect a PC to a receiver network using an Ethernet connection instead of USB.1. Connect the PC to the receiver network at the network hub. 2.Set the computer’s IP address to 10.0.0.2 and the subnet mask to 255.0.0.0. To do this, go to Control Panel, open Network Connec-tions, right-click on Local Area Connection and select Properties. Select Internet Protocol (TCP/IP) and click Properties.DHCP NetworksTo add receivers to an existing DHCP network, set all the networked receivers to use DHCP (Util > Network > Mode = DHCP, see page 6). You can access the receivers from any computer on the network that is running the Wireless Workbench software. Other Network ConfigurationsUHF-R receivers operate on a network just like any other Ethernet device. Both static addressing and DHCP are supported. Each re-ceiver ships with a unique IP address based on its MAC address, so in most situations, you don’t need to change the receiver’s network settings to connect it to a network.NOTE: Dual receivers use a single IP address, which may be set through either LCD interface.Existing UHF Network InstallationsBoth Shure’s UHF-R receivers and legacy UHF receivers can be networked to the same PC and accessed using the latest Wireless Workbench software.Ethernet Hub/SwitchEthernet CableUSBETHERNETUSBRS-232U888UHFUHF-R
9EnglishHandheld and Bodypack Transmitter Controls and Connectors쐃Interchangeable microphone head (BETA 87A pictured).쐇LCD display Panel.쐋Power Switch.쐏Control buttons for LCD interface.쐄Infrared (IR) port. See page 11.쐂Battery compartment.쐆Detachable Flexible Antenna.쐊Power LED.쐎4-Pin Microphone Input Jack.쐅Belt Clip.Transmitter LCD InterfaceTransmitter BatteriesTransmitters operate on standard AA batteries. Turn off the transmitter before changing the batteries.The battery fuel gauge displayed on the transmitter LCD gives an approximate indication of remaining battery life, as shown below. 쐇쐆쐄쐏쐊쐋쐂쐎쐅Transmitter DisplayApproximate Hours Remaining (alkaline batteries)Normal Power High Power*7.5 to 9.5 5.5 to 6.55.75 to 7.5 5. to 5.54 to 5.75 4 to 52 to 4 2.5 to 415 minutes to 2 hours 15 minutes to 2.5 hours* High power setting not available with models sold in countries that prohibit its use.779.475MHzexit Key. Move to the left, or exitwithout saving changes.Down Arrow Key. Scroll down or decrease a value.enter Key. Press to select parameters and accept the selected value.Up Arrow Key. Scroll up or increase a value.Main Menu
10Shure UHF-R WirelessTransmitter ParametersSetting Transmitter GainAdjust the transmitter gain and input sensitivity so that the Audio LEDs on the receiver peak within the yellow range during use. On the bodypack transmitter, you can change the sensitivity setting to compensate for different audio levels when connecting different intruments or microphones to the input.To adjust gain, turn on the transmitter and press the enter button. Scroll down to the Gain parameter or the Sens parameter (body-pack only) and press enter again. Use the arrow keys to adjust the setting and press enter to save it (Exit cancels without saving).RF Safety ModeThis special feature temporarily mutes RF broadcast. This allows you to change frequency settings on a transmitter without accidentally “cutting in” on a channel being used by another transmitter.1. Turn the transmitter off.2. Hold down exit key while turning on the transmitter power (for handheld microphones, you need to pull the battery cover off the handle). The LCD flashes while the unit is in RF safety mode.3. Change group and channel settings as you normally would—the transmitter will not broadcast.4. Power the transmitter off and on to exit RF safety mode.Group (G) and Channel (Ch). Must match the receiver’s settings.Frequency (MHZ). Manual frequency selection in 0.025 MHz increments.Gain (Gain). Adjusts audio level from –10 dB to +20 dB.Sensitivity (Sens) (bodypack only). Sets audio input to +15 dB, 0 dB, or –10 dB. Name Display. 12-digit ASCII.SHURE INC.G:34 Ch:21779.475MHZGain +20dBSet BL FreqPress ENTER from the main menu to access the following parameters:holdhold LCD DisplayPanelChanges LCD Display PanelFrequency LockToggles setting. When enabled, frequency cannot be changed, and a transmitter sync will not overwrite the frequency setting.Power LockToggles power lock. When locked, power switch does not turn off transmitter.RF power level setting*Use the arrow keys to select normal (10 mW) or high power (50/100 mW**). Use the normal power setting to conserve batteries or prevent RF overload at the receiver.* High power setting not available with models sold in countries that prohibit its use.** High power value varies with model.tapholdtapholdhold holdUse the following key combinations to access additional features and parameters: Lock IndicatorsPower LockFrequency Lock
11EnglishAutomatic Transmitter SyncThis feature automatically updates a bodypack or handheld transmitter’s group and channel settings to match those of a selected receiver. To perform a transmitter sync...1.Open the transmitter battery cover to display the infrared (IR) port.2.With the IR port exposed to the receiver, select Sync > Send from the receiver LCD interface. The display on the receiver indicates whether the sync was successful. If the sync fails, try again, making sure that the IR port on the transmitter is exposed and directly faces the IR port on the receiver.NOTE: Close the battery door before performing a sync on other transmitters.To transfer other transmitter settings...Optionally, you can transfer other transmitter settings from a receiver when you perform a sync. Use the following steps:1.Select Sync > Setup from the receiver LCD interface. 2.Turn the Control wheel to change parameter settings.3.Push the Control wheel to move to the next parameter.4.Push the flashing ENTER button to save the settings.The transmitter settings you set on the receiver remain for future syncs.NOTE: If you don’t want the sync to send a setting, set the parameter to No ChangeAvailable Settings...The following settings are available from the Sync > Setup menu:• Sensitivity (Sens) bodypack only• Gain (Gain)•RF Power (Pwr)• Power and Frequency Lock (Lock), which has the following values:Power lock only: (Pwr Only)Frequency lock only: (Freq only)Both: (Freq and Pwr)Neither: (Unlock)Audio ABJ 779-810 MHz NavigateRFOL OLAudio ABJ 779-810 MHz NavigateRF®UR4DWireless Receiverwith Audio ReferenceCompandingsyncControl Monitor PowersyncMonitor ClipENTEREXITpush12
12Shure UHF-R WirelessTroubleshootingPowerMake sure that the transmitter and receiver are receiving suffi-cient voltage. The receiver requires at least 90 Vac. Check the battery indicator on the transmitter and replace battery if nec-essary.GainAdjust the transmitter gain and sensitivity settings (see page 10) or the receiver output level (page 5), or toggle the mic/line switch on the back of the receiver.CablesCheck that all cables and connectors are in working order.Ground LiftLifting the ground on pin 1 of the XLR output on the receiver can sometimes remove hum or buzz in the audio signal. Set the GND/LIFT switch on the receiver to LIFT if you are using the XLR connector.Interface LocksBoth the transmitter and receiver can be locked to prevent ac-cidental changes. On transmitters, look for a lock symbol on the LCD and use the key combinations illustrated on page 10 to turn it off.To turn off the receiver interface lock, see page 5.Radio Frequency (RF)Using the RF LEDsIf neither blue RF LED is illuminated, then the receiver is not de-tecting the presence of a transmitter. The amber RF LEDs indicate the amount of signal being re-ceived. This signal could be from the transmitter, or it could be from an interfering source, such as a television broadcast. Turn the transmitter off. If more than one or two of the amber RF LEDs are still illuminated, then that channel has too much inter-ference, and you should try a different channel.The red RF LED indicates RF overload. This will usually not cause a problem unless you are using more than one system at the same time, in which case, it can cause interference be-tween systems.Compatibility• Perform a transmitter sync, or make sure the transmitter andreceiver are set to the same group and channel.• Look at the label on the transmitter and receiver to make surethey are in the same band (H4, J5, L3, etc...).Reducing Interference• Use a different channel or perform an automatic group orchannel scan (see page 7).• For multiple systems, check that all systems are set to chan-nels in the same group (systems in different bands do notneed to be set to the same group).• Maintain a line of sight between transmitter and receiver an-tennas• Move receiver antennas away from metal objects or othersources of RF interference (such as CD players, computers,digital effects, and Personal Stereo Monitor (PSM) wirelesssystems).• Eliminate RF overload (see below).Increasing RangeIf the transmitter is more than 6 to 60 m (20 to 200 ft) from the receiver antenna, you may be able to increase range by doing one of the following:• Reduce interference (see above)• Increase transmitter RF power level (see page 10).• Use an active directional antenna, antenna distribution sys-tem, or other antenna accessory to increase RF range (seepage 15).Eliminating RF OverloadIf you see the red RF LED on a receiver, reduce the transmitter RF power level (see page 10) or move the transmitter further away from the receiver—at least 6 m (20 ft). If you are using ac-tive antennas, reduce antenna or amplifier gain.Issue See Solution...No sound Power, Cables, or RFFaint Sound or Distortion GainLack of range, unwanted noise bursts, or drop outs RFCannot turn transmitter off or change frequency settings, or can’t program receiver Interface LocksExcessive hum or buzzing Ground lift
13EnglishSpecificationsFrequency Range and Transmitter Output PowerRF Carrier Frequency Range518-862 MHz, depending on regionWorking RangeUR1, UR2: 152.4 m (500 ft.) minimum, under typical conditions;487.6 m (1600 ft.) line of sightNOTE: Actual working range depends on RF signal absorption,reflection and interferenceAudio Frequency Response50-18,000 Hz, ±1 dB.NOTE: Overall system frequency response depends on the microphoneelementGain Adjustment RangeUR1: –20 to +35 dBUR2: –10 to +20 dBModulationFM (45 kHz max. deviation), compander system with pre- andde-emphasisRF Power OutputUR1, UR2: 10/50 mW, 10/100 mW maximum See table above.Dynamic Range>102 dB or >110dB, depending on region; A-weightedImage Rejection110 dB typicalRF SensitivitySpurious Rejection90 dB typicalUltimate Quieting (ref. 45 kHz deviation)>100 dB, A-weighted1/4 inch Output Signal PolarityPositive pressure on microphone diaphragm (or positive voltageapplied to tip of WA302 phone plug) produces positive voltageon XLR output pin 2 with respect to XLR pin 3 of low impedanceoutput and on the tip of the high impedance 1/4-inch output jack.outputSystem Distortion (ref. ± 45 kHz deviation, 1 kHz modulation)0.3% Total Harmonic Distortion typicalPower RequirementsUR1, UR2: Two 1.5V AA alkaline batteries rechargeable batter-ies optionalUR4: 90 100 to 230 240 Vac, 50/60 Hz Current DrainUR1, UR2: 180 mA max. (normal RF power setting) 240 mA max. (high RF power setting)UR4D: 0.8 Amps max.UR4S: 0.8 Amps max.Power ConsumptionUR4S: 9.6 W min., 13.2 W max. 0.8 A max,UR4D: 12 W min.,16 W max. 0.8 A max.UA845: 15 W min., 16 W max.Battery Life (Typical)UR1, UR2: 8 hours (low power)Operating Temperature Range–18° to +57° C (0° to +135° F) NOTE: Battery characteristics may limit this range changeNOTE: Electrical safety approval is based on a maximum ambient temperature of 35°C.Overall DimensionsUR1: 98 mm L x 60 mm W x 17 mm D (3.84 x 2.38 x 0.66 in.)UR2/SM58: 261 mm L x 51 mm Dia. (10.27 x 2 in.)UR2/SM86: 261 mm L x 49 mm Dia. (10.27 x 2 in.)UR2/SM87A: 254 mm x 49 mm Dia. (10 x 2 in.)UR2/BETA 58: 258 mm L x 53 mm Dia. (10.15 x 2 in.)UR2/BETA 87A, UR2/BETA 87C: 254 mm x 50 mmDia. (10 x 2 in.)UR4S/UR4D: 43.5 mm H x 482.6 mm W x 365.38 mm D(1.718 x 19.000 x 14.385 in.)Net Weight UR1: 94 g (3 1/4 oz.) without batteryUR2/SM58: 346 g (12 oz.) without batteryUR2/BETA 58: 306 g (11 oz.) without batteryUR2/SM86: 308 g (11 oz.) without batteryUR2/SM87A: 301 g (10.5 oz.) without batteryUR2/BETA 87A, U2/BETA 87C: 315 g (11 oz) without batteryUR4S: 4.34 kg (9.5 lbs)UR4D: 4.54 kg (10 lbs)Housing:UR1: Cast magnesiumUR2: Aluminum die-cast handle and aluminum machined bat-tery cupUR4S, UR4D: Galvanized steelWiringBand Range Transmitter power (mW)Handheld BodypackH4E, H4 518-578 MHz 10 mW / 50 mW 10 mW / 50 mW 10 mW / 50 mW10 mW / 100 mWJ5E, J5 578-638 MHz(578-608, 614-638) 10 mW / 50 mW10 mW / 50 mW 10 mW / 50 mW 10 mW / 100 mWL3E, L3 638-698 MHz 10 mW / 50 mW10 mW / 50 mW 10 mW / 50 mW10 mW / 100 mWQ5 740-814 MHz 10 mW / 50 mW 10 mW / 50 mWR9 798-862 MHz 10 mW / 50 mW 10 mW / 50 mWQ6 740-752 MHz 10 mW 10 mW A24 779-788 / 797-806 MHz 10 mW 10 mW JBX 806-810 MHZ 10 mW 10 mW Q9 740-806 MHz 10 mW / 50 mW 10 mW / 50 mWQ10 740-798 MHz 10 mW / 50 mW 10 mW / 50 mWNOTEThis Radio equipment Is Intended for use In musical professionalentertainment and similar applications.This Radio apparatus may be capable of operating on some frequen-cies not authorized in your region. Please contact your national au-thority to obtain information on authorized frequencies and RF powerlevels for wireless microphone products.UR4S UR4D–110 dBm Typical12 dB SINAD –107 dBm Typical12 dB SINAD–105 dBm Typical30 dB SINAD –102 dBm Typical30 dB SINADdcMICROPHONE ELEMENT TA4FConnector TA4M ConnectorAudioGroundUR1 MIC JACK BOARDNOTE: LAVALIER MIC TIES PINS 3 AND 4 TOGETHER—GUITAR CABLE DOES NOT.Active Load
14Shure UHF-R WirelessInputs and OutputsUR1 Transmitter Audio InputUR1 Transmitter RF OutputUR2 Transmitter Audio InputUR2 Transmitter RF OutputReceiver Input* For remote antenna amplifiersReceiver Audio OutputComputer/Network InterfaceConnector: 4-Pin male mini connector (TA4M)Input Configuration: Unbalanced, activeActual Impedance: >1 MΩ (active load)Maximum Input Level:Nominal?????6 Vp-p (+7 dBV) for 1% THD at minimum gain setting using 1 kHz signal. TA4M Connector Pin Assignments:Pin 1: Tied to GroundPin 2: Tied to +5 Vdc biasPin 3: Tied to AudioPin 4: Tied through active load (on main board) to Ground. (On instrument adapter cable, Pin 4 floats)Connector: SMAActual Impedance: 50 ΩPin Assignments: Shell = GroundCenter = SignalInput Configuration: Unbalanced, activeActual Impedance: >1 MΩ (active load)Maximum Input Level: 3 Vp-p (0.5 dBV) for 1% THD at minimum gain setting using 1 kHz signal.Connector: SMAActual Impedance: 50 ΩPin Assignments: Shell = GroundCenter = SignalConnector: Antenna Power InputConnector Type: BNC IECActual Impedance: 50 Ω -Nominal Input Level: –95 to –30 dBm 100-240 VAC,50/60 HzMaximum Input Level:+6 dBm(–20 dBm recommended)?nominal?240 VAC, + 10%, 50/60 HzPin Assignments: Shell = GroundCenter = Signal IEC StandardBias Voltage* forRemote Power:12.2 Vdc @ 150 mA maximum N/AMonitor(1/4” Headphone) 1/4” Phone XLROutput Configuration: Unbalanced mono, 1/4 inch Impedance Balanced Electrically BalancedActual Impedance: 50 Ω200 Ω200 Ω(150 Ω mic)Maximum Output Level 1 Watt @ 63 Ω+18 dBu +24 dBu(–6 dBu mic)Pin Assignments: Tip = HotRing = HotSleeve = GndTip = HotRing = no signal Sleeve = Gnd1 = Ground2 = Audio +3 = Audio –Phantom Power Protection? No Yes YesEthernet USB RJ45 USB Series B ReceptacleXLR1/4” Monitor/headphone1/4” Phone
15EnglishReplacement Parts and AccessoriesFurnished AccessoriesOptional AccessoriesAntenna Combiners and Accessories• Antennas and receivers must be from the same frequencyband.• The supplied 1/2 wave antennas can be used when remotelymounted or mounted directly to the UA845. If antennas areremotely mounted, 1/2 wave antennas must be used.• Antennas and cables for use with the UA845 can also beused with stand-alone UHF-R receivers.Architects' and Engineers' SpecificationsThe wireless system shall operate in the UHF band between 518 MHz and 862 MHz, with the specific range being dependent on the user's locale. The system shall include the option of changing the operating frequency in order to avoid RF interference, enabling up to 140?? systems to operate simultaneously in the same location. Preconfigured group, channel and frequency setups shall be avail-able to ensure that multiple systems in use do not interfere with one another.All transmitters shall be powered by 2 AA alkaline batteries and shall have a power on/off switch. The bodypack will have an LED in-dicating that power is on. Available transmitters shall include: a body pack for use with electric guitars, basses, and other electric in-struments, and a handheld microphone for vocals. The transmitters shall have a DC/DC converter to ensure consistent performance, even if battery voltages change.The receiver shall have a user-programmable, menu-driven LCD showing group, channel, frequency, name, squelch level, and locked/unlocked status. The system shall use technology such as MARCAD signal combining circuitry to improve reception, minimize signal dropouts, and achieve the best possible signal-to-noise ratio. An equalizer, tone key squelch, and noise squelch circuitry shall be built into the system to provide optimal sound quality and minimize unwanted noise. The receiver shall include dual RF meters (one for each antenna), an audio level meter, and a Networking Interface connector for computer control and monitoring. The receiver shall have a volume control and an adjustable noise squelch control.The system shall be the Shure UHF-R Wireless.Microphone Stand Adapter (UR2) WA371Zipper Bag (UR1) 26A13Zipper Bag (UR2) 26A14Antenna Extension Cables (2) 95A9023Hardware Kit, Locking Connector WA340Antenna (UR1), 518-578 MHz UA710Antenna (UR1), 578-638 MHz UA720Antenna (UR1), 638-862 MHz UA730Two Antennas (UR4), Band Dependent (see next page table)UA820Transmitter Carrying Case 95A9053SM58 Head with Grille RPW112SM86 Head with Grille RPW114BETA 58 Head with Grille RPW118BETA 87A Head with Grille RPW120BETA 87C Head with Grille RPW122SM87A Head with Grille RPW116Matte Silver Grille (SM58) RK143GMatte Silver Grille (SM86) RPM226Matte Silver Grille (BETA 58) RK265GBlack Grille (SM87) RK214Matte Silver Grille (BETA 87A) RK313Matte Silver Grille (BETA 87C) RK312Black Grille (BETA 58) RK323Black Grille (BETA 87A/BETA 87C) RK324GBelt Clip 44A8031Body-Pack Pouch (Black), UR1 WA580BBody-Pack Pouch (White), UR1 WA580WPassive Antenna/Splitter Combiner Kit (recommended for 2 receivers) UA221UHF Antenna Power Distribution Amplifier (recommended for 3 or more receivers) UA845WBU.S.A. UA845USEurope UA845EUK UA845UK1/2 Wave, Omnidirectional, Wideband Antenna UA860WBActive Directional Wideband Antenna UA870WBWideband In-Line RF Amplifier UA830WBPassive Unidirectional Wideband Antenna PA805WB1/2 wave antennas (2)H4E, H4 Band UA820H4J5E, J5 Band UA820JL3E, L3 Band UA820L3Q5, Q6,Q9 Bands UA820QR9, ABJ, Q10 Bands UA820A25’ Antenna Cable (RG-8/X) UA82550’ Antenna Cable (RG-8/X) UA850100’ Antenna Cable UA8100
16Shure UHF-R WirelessCertificationUR1, UR2: Type Accepted under FCC Parts 74. Certified by IC in Canada under TRC-78.UR1, UR2: Type Accepted under FCC Parts 74 (FCC ID: "DD4UR1" & "DD4UR2"). Certified by IC in Canada under RSS-123 and RSS-102 ("IC: 616A-UR1" and "IC: 616A-UR2"). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and is eligible to carry the CE marking. UR4S, UR4D: UL and cUL Listed to UL 813 and CSA C22.2 No. 1. VDE Certified to EN 60 950. Approved under the Notification provisionof FCC Part 15; Certified by IC in Canada under TRC-78.UR4S, UR4D: Authorized under the Declaration Of Conformity provision of FCC Part 15. Certified under Industry Canada to RSS-123("IC: 616A-UR4"). Meets the essential requirements of the European R&TTE Directive 99/5/EC (EN 301 489 Parts 1 & 9, EN 300 422Parts 1 and 2). Eligible to carry the CE marking. Conforms to Australian EMC requirements and is eligible for C-Tick marking.Have been granted the following Country Safety Approvals:cULus Mark for US and Canada: Meets UL6500 and CSA/CAN E60065. UL GS-Certified to EN60065.LICENSING INFORMATION:Licensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements.Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing ofShure wireless microphone equipment is the user's responsibility, and licensability depends on the user's classification and application,and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning properlicensing, and before choosing and ordering frequencies.Information to UserThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment gen-erates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.This apparatus complies with Canadian ICES-003. “Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Note: EMC conformance testing is based on the use of supplied and recommended cable types. The use of other cable types may degrade EMC performanceN108
17English
18Shure UHF-R WirelessSHURE Incorporated http://www.shure.comUnited States, Canada, Latin America, Caribbean:5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446Europe, Middle East, Africa:Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414Asia, Pacific:Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055

Navigation menu