Shure orporated PG1A Non-Broadcast Transmitter Worn on Body User Manual Exhibit D Users Manual per 2 1033 c3

Shure Incorporated Non-Broadcast Transmitter Worn on Body Exhibit D Users Manual per 2 1033 c3

Exhibit D Users Manual per 2 1033 c3

Congratulations on purchasing your Shure Performance Gear Wireless system. Shure professional audio products deliver legendary sound quality, stage-proven durability and hassle-free setup for worry-free performance.Performance Gear Wireless systems are available in a variety of configurations for handheld, guitar, headset, and presentation applications. Startup channelreadyaudioInternal DiverBusy Indicator When selecting channels, a flashing dash indicates interference from television broadcasts, electronic devices or other wireless systems. CHANNEL6MUTEchannelmutechannelreadyaudioInternal Antenna Diversity channelmutechannelmute Accessing Gain Switch channelmute Testing Audio Talk or sing into the microphone or play instrument. 0dB For instrument or quiet to normal vocal performance (default).–10dB Use if audio is distorted due to high vocal or instrument levels. mic Use for headworn or lavalier microphones (PG1 only).CHANNEL D"MICchannelreadyaudioInternal Diver ENGLISH Changing Channels Press and hold the channel button until the display starts flashing.Internal AntenchannelreadyaudioWhile the display is flashing, press the channel button.The channel is active once the display stops flashing. channelmutechannelreadyaudioInternal Antenna Diversity channelmuteReceiver and transmitter channels should match. Multiple gain settings are available on the PG1 and PG2 transmitters. To change gain settings, see below. Follow these simple steps to check for interference and to set your receiver and transmitter to the same channel . If you haven’t installed the battery, do it now and leave the cover off. Turn ON the handheld or bodypack transmitter by pressing the power button. The channel display should illuminate. The ready LED on the receiver should be illuminated.Replace battery cover. Check to see that the transmitter and the receiver display the same channel .channelreadyaudioInternal Diversity Antenna SystechannelmuteInternal Antenchannelreadyaudio©2006, Shure Incorporated 27EN8865 (Rev. 3)Printed in U.S.A.The audio LED on the receiver should flicker green or amber, if red, adjust the Gain Switch .If this occurs, change the channel. Lock system controls to prevent accidental muting. To lock controls: Turn transmitter off. Remove Battery Cover. Press and hold Channel Button. Press and release Power/Mute button. Power/Mute LED will flash red and green. To unlock controls: Press and hold Power/Mute button down until Power/Mute LED flashes red and green. Locking and Unlocking Transmitter ControlsIt turns off after ten seconds to conserve battery. Wearing the Bodypack Transmitter Clip the transmitter to belt or guitar strap as shown. Make sure the antenna is unobstructed. Changing Battery Expected life for a 9 volt alkaline battery is approximately 8 hours.When the Power/Mute LED glows red, the battery should be replaced immediately. System Componentsaudio ready channelDiversity Antenna SystemPG4audio ready channelaudio ready channel PG1BodypackTransmitter PG2 Handheld Transmitter PG4 Wireless Receiver PG88 Dual Wireless Receiver PS20 Power Supply PG185Lavalier Mic Features PG30Headworn Mic Turn OFF the microphone or bodypack.If left on, it will create a false busy indicator.Plug in the power supply.  There is no power switch. The channel display should illuminate. If you see the Busy Indicator (a flashing dash) change the channel. Press and hold down the channel button until the display begins flashing.Wait for the channel display to stop flashing.    
Issue LED Status Solution No sound or faint sound Transmitter Power/Mute LED on, receiver LEDs on • Perform transmitter setup. • Verify all sound system connections. • Adjust transmitter gain.Receiver Channel Display off • Make sure AC adapter is securely plugged into electrical outlet and into POWER connector on rear panel of receiver.• Make sure AC electrical outlet works and is supplying proper voltage. Transmitter LED glowing or flashing red• Replace transmitter battery. Transmitter LED off • Turn transmitter on. • Make sure the +/– indicators on battery match transmitter terminals. • Insert fresh battery. Distortion or unwanted noise bursts • Remove nearby sources of RF interference (CD players, computers, cell phones, digital effects, in-ear monitor systems, etc.) • Select a new channel for both receiver and transmitter. • Reduce transmitter gain. • Replace transmitter battery. • If using multiple systems, change the channel of one of the active systems. Sound level different from cabled guitar or microphone, or when using different guitars • Adjust transmitter gain as necessary. Cannot turn transmitter on Transmitter LED flashing red• Replace transmitter battery. TroubleshootingRegulatory InformationReplacement PartsTechnical SpecificationsAudio Input Level –10 dBV maximum at “mic” gain position +10 dBV maximum at 0dB gain position +20 dBV maximum at –10dB gain positionGain Adjustment Range 30 dBInput Impedance 1mΩRF Transmitter Output 10 mW typical (dependent on applicable country regulations)Dimensions 110 mm H x 64 mm W x 21 mm D (4.3 x 2.5 x 0.8 in.)Weight 75 grams (2.6 oz.) without batteryHousing Molded ABSPower Requirements One 9V alkaline or rechargeable batteryBattery Life >8 hours (alkaline)Working Range 75m (250 ft.) Note: actual range depends on RF signal absorption, reflection, and interference. Audio Channel Response Minimum: 45 Hz. Maximum: 15 kHz (overall system channel depends on microphone element).Total Harmonic Distortion 0.5%, typical Ref. +/– 33 kHz deviation, 1 kHz tone Dynamic Range >100 dB A-weighted, typicalOperating Temperature Range–18°C (0°F) to +57°C (+135°F) Note: battery characteristics may limit this rangeTransmitter Audio Polarity Positive pressure on microphone diaphragm (or positive voltage to tip of WA302 phone plug) produces positive voltage on pin 2 (with respect to pin 3 of low impedance output) and the tip of the high impedance 1/4-inch output.Audio Input Level +2 dBV maximum at –10dB position –8 dBV maximum at 0dB position Gain Adjustment Range 10dBRF Transmitter Output 10 mW typical (dependent on applicable country regulations)Dimensions 223.52 L x 53.34 Dia. (8.8 in. x 2.10 in.)Weight 218 grams (7.7 oz.) without battery Housing Molded ABS handle and battery cupPower Requirements One 9V alkaline or rechargeable batteryBattery Life >8 hours (alkaline)Output Impedance XLR connector: 200 Ω 1/4 inch connector: 1kΩAudio Output Level Ref. +/– 33 kHz deviation with 1 kHz toneXLR connector (into 100K Ω load): –19 dBV, typical 1/4 inch connector (into 100K Ω load): –5 dBV, typical Sensitivity –105 dBm for 12 dB SINAD, typical Image Rejection >50 dB, typicalDimensions 188 mm L x 103 mm W x 40 mm D (7.4 in. x 4.0 in. x 1.5 in.) Dimensions - PG88 388 mm L x 116 mm W x 40 mm D (15.3 in. x 4 in. x 1.5 in.) Weight 241 grams (8.5 oz)Weight - PG88 429 grams (15.1 oz)Housing Molded ABSPower Requirements 12–18 Vdc at 160 mA (PG4), 320mA (PG88), supplied by external power supply SystemPG1 Bodypack TransmitterPG2 Handheld TransmitterRegulatory Information for North America, Europe, and Australia PG1 & PG2 Transmitters: Certified to FCC Part 74 (FCC ID: “DD4PG1” and “DD4PG2”). Certified by IC in Canada under RSS-123 and RSS-102 (“IC: 616A-PG1” and “IC: 616A-PG2”). Meets the essential requirements of the European R&TTE Directive 99/5/EC (ETSI EN 300-422 Parts 1 & 2, EN 301 489 Parts 1 & 9) and are eligible to carry the CE marking. PG4 and PG88 Receiver: Authorized under Declaration of Conformity (DoC) provision of FCC Part 15. Certified under Industry Canada to RSS-123 (“IC: 616A-PG4”). This class B digital apparatus complies with Canadian ICES-003. Meets the essential requirements of the European R&TTE Directive 99/5/ EC (EN 301 489 Parts 1 & 9, EN 300 422 Parts 1 & 2) and is eligible to carry the CE marking. Conforms to Australian EMC requirements and is eligible for C-Tick marking. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio channel energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help.PS20 Series Power Supplies: Conform to Safety Standard IEC 60065.PS20E and PS20UK are eligible to bear CE marking.N108Z5400978Technical Specifications cont’dPG4 and PG88 ReceiverSHURE Incorporated http://www.shure.comUnited States, Canada, Latin America, Caribbean:5800 W. Touhy Avenue, Niles, IL 60714-4608, U.S.A.Phone: 847-600-2000 U.S. Fax: 847-600-1212 Int’l Fax: 847-600-6446Europe, Middle East, Africa:Shure Europe GmbH, Phone: 49-7131-72140 Fax: 49-7131-721414Asia, Pacific:Shure Asia Limited, Phone: 852-2893-4290 Fax: 852-2893-4055Changes or modifications not expressly approved by Shure Incorporated for compliance could void the user’s authority to operate the equipment. Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.Caution!System ComponentsAll SystemsPG4 or PG88 Receiver Internal Diversity Antenna SystemOne 9 volt battery AC Power supply User guide Vocalist SystemMicrophone Head PG2 handheld transmitter Microphone clipInstrument SystemPG1 bodypack transmitter4-pin mini connector (TA4F) to 1/4” connector cableLavalier and Headworn System PG1 bodypack transmitter Microphone (choice of PG185, PG30)PatentsPatent numbers 6,597,301 and 6,296,565All Systems Microphone Stand Adapter (PGX2) WA371System-Specific AC Adapter (120 VAC, 60 Hz) PS20AC Adapter (220 VAC, 50 Hz), Argentina PS20ARAC Adapter (230 VAC, 50/60 Hz, Europlug) PS20EAC Adapter (230 VAC, 50/60 Hz, UK) PS20UKAC Adapter (100 VAC, 50/60 Hz) PS20JAC Adapter (220 VAC, 50 Hz, China) PS20CHNAC Adapter (230 VAC, 50 Hz,, Australia) PS20AZAC Adapter (220 VAC, 60 Hz, Korea PS20KPG58 Head with Grille RPW108Belt Clip 44A8035Optional Universal Rack Tray URT4-pin mini connector (TA4F) to 1/4” connector cableWA302A ministerial license may be required to operate this equipment in certain areas. Consult your national authority for possible requirements.This radio equipment is intended for use in musical professional entertainment and similar applications. LED Status TRANSMITTER LED COLOR STATUSGreen ReadyAmber Mute on Red Battery lowFlashing Red on startup Battery is dead Flashing Green and Red Controls lockedFlashing Amber and Red Mute on, battery lowRECEIVERAUDIO LED COLOR INDICATESGreen Normal signal strengthAmber Strong signalRed Peak signalREADY DISPLAY COLOR INDICATESGreen System is ready To set up multiple systems, repeat the previous steps for each transmitter and receiver pair. Once transmitters have been set, leave them on. Be sure to set each transmitter and receiver pair to a different channel. For information about frequencies and compatibility, refer to channel guide.Multiple System Setup
©2007 Shure Incorporated Printed in USA27A8898 (Rev. 1)PG Wireless User Guide Supplement:X1 INTER-GROUP AVAILABILITY: PG Wireless X1 944-952MHzThe following table describes Frequency and Channel availablility.ChannelGroup 11 944.600 Compatible Frequencies2 946.275 3 947.475 4 949.800 5 944.300 Compatible Frequencies6 945.975 7 947.175 8 949.500 9 951.825 Alternate Frequencies10 951.525 COMPLIANCE INFORMATIONType accepted under FCC Part 74, FCC ID DD4PG2A. Type accepted under FCC Part 74, FCC ID DD4PG1A.

Navigation menu