Shure orporated MXW1 BodyPack Transmitter User Manual

Shure Incorporated BodyPack Transmitter

User Manual

©2012 Shure Incorporated27WG20831 (Rev. 1)MXW Wireless Conference System10/02/12
10/02/12
IMPORTANT SAFETY INSTRUCTIONS1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-tion and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.21. Operate this product within its specified operating temperature range.This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte-nance instructions in the literature accompanying this unit. WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.INSTRUCCIONES IMPORTANTES DE SEGURIDAD1. LEA estas instrucciones. 2. CONSERVE estas instrucciones. 3. PRESTE ATENCION a todas las advertencias.4. SIGA todas las instrucciones. 5. NO utilice este aparato cerca del agua. 6. LIMPIE UNICAMENTE con un trapo seco. 7. NO obstruya ninguna de las aberturas de ventilación. Deje espacio suficiente para proporcionar ventilación adecuada e instale los equipos según las instrucciones del fabricante. 8. NO instale el aparato cerca de fuentes de calor tales como llamas descubiertas, radiad-ores, registros de calefacción, estufas u otros aparatos (incluyendo amplificadores) que produzcan calor. No coloque artículos con llamas descubiertas en el producto. 9. NO anule la función de seguridad del enchufe polarizado o con clavija de puesta a tierra. Un enchufe polarizado tiene dos patas, una más ancha que la otra. Un enchufe con pu-esta a tierra tiene dos patas y una tercera clavija con puesta a tierra. La pata más ancha o la tercera clavija se proporciona para su seguridad. Si el tomacorriente no es del tipo apropiado para el enchufe, consulte a un electricista para que sustituya el tomacorriente de estilo anticuado. 10. PROTEJA el cable eléctrico para evitar que personas lo pisen o estrujen, particularmente en sus enchufes, en los tomacorrientes y en el punto en el cual sale del aparato. 11. UTILICE únicamente los accesorios especificados por el fabricante.12. UTILICE únicamente con un carro, pedestal, trípode, escuadra o mesa del tipo especificado por el fabricante o vendido con el aparato. Si se usa un carro, el mismo debe moverse con sumo cuidado para evitar que se vuelque con el aparato.13. DESENCHUFE el aparato durante las tormentas eléctricas, o si no va a ser utilizado por un lapso prolongado. 14. TODA reparación debe ser llevada a cabo por técnicos calificados. El aparato requiere reparación si ha sufrido cualquier tipo de daño, incluyendo los daños al cordón o enchufe eléctrico, si se derrama líquido sobre el aparato o si caen objetos en su interior, si ha sido expuesto a la lluvia o la humedad, si no funciona de modo normal, o si se ha caído. 15. NO exponga este aparato a chorros o salpicaduras de líquidos. NO coloque objetos llenos con líquido, tales como floreros, sobre el aparato. 16. El enchufe de alimentación o un acoplador para otros aparatos deberá permanecer en buenas condiciones de funcionamiento. 17. El nivel de ruido transmitido por el aire del aparato no excede de 70 dB(A). 18. Los aparatos de fabricación CLASE I deberán conectarse a un tomacorriente de ALI-MENTACION con clavija de puesta a tierra protectora. 19. Para reducir el riesgo de causar un incendio o sacudidas eléctricas, no exponga este aparato a la lluvia ni a humedad. 20. No intente modificar este producto. Hacerlo podría causar lesiones personales y/o la falla del producto.21. Utilice este producto únicamente dentro de la gama de temperaturas de funcionamiento especificadas.Este símbolo indica que la unidad contiene niveles de voltaje peligrosos que representan un riesgo de choques eléctricos.Este símbolo indica que la literatura que acompaña a esta unidad con-tiene instrucciones importantes de funcionamiento y mantenimiento.ISTRUZIONI IMPORTANTI PER LA SICUREZZA1. LEGGETE queste istruzioni. 2. CONSERVATELE. 3. OSSERVATE tutte le avvertenze.4. SEGUITE tutte le istruzioni. 5. NON usate questo apparecchio vicino all'acqua. 6. PULITE l'apparecchio SOLO con un panno asciutto. 7. NON ostruite alcuna apertura per l'aria di raffreddamento. Consentite distanze sufficienti per un'adeguata ventilazione e installate l'apparecchio seguendo le istruzioni del costrut-tore. 8. NON installate l'apparecchio accanto a fonti di calore, quali fiamme libere, radiatori, aper-ture per l'efflusso di aria calda, forni o altri apparecchi (amplificatori inclusi) che generano calore. Non esponete il prodotto a fonti di calore non controllate. 9. NON modificate la spina polarizzata o con spinotto di protezione per non alterarne la funzione di sicurezza. Una spina polarizzata è dotata di due lame, una più ampia dell'altra. Una spina con spinotto è dotata di due lame e di un terzo polo di messa a terra. La lama più ampia ed il terzo polo hanno lo scopo di tutelare la vostra incolumità. Se la spina in dotazione non si adatta alla presa di corrente, rivolgetevi ad un elettricista per far eseguire le modifiche necessarie. 10. EVITATE di calpestare il cavo di alimentazione o di comprimerlo, specie in corrispon-denza di spine, prese di corrente e punto di uscita dall'apparecchio. 11. USATE ESCLUSIVAMENTE i dispositivi di collegamento e gli accessori specificati dal costruttore.12. USATE l'apparecchio solo con carrelli, sostegni, treppiedi, staffe o tavoli specificati dal produttore o venduti unitamente all'apparecchio stesso. Se us-ate un carrello, fate attenzione quando lo spostate con l'apparecchio collocato su di esso, per evitare infortuni causati da un eventuale ribaltamento del carrello stesso.13. Durante i temporali o in caso di inutilizzo prolungato dell'apparecchio, SCOLLEGATELO dalla presa di corrente. 14. Per qualsiasi intervento, RIVOLGETEVI a personale di assistenza qualificato. È neces-sario intervenire sull'apparecchio ogniqualvolta è stato danneggiato, in qualsiasi modo; ad esempio la spina o il cavo di alimentazione sono danneggiati, si è versato liquido sull'apparecchio o sono caduti oggetti su di esso, l'apparecchio è stato esposto alla piog-gia o all'umidità, non funziona normalmente o è caduto. 15. NON esponete l'apparecchio a sgocciolamenti o spruzzi. NON appoggiate sull'apparecchio oggetti pieni di liquidi, ad esempio vasi da fiori. 16. La spina ELETTRICA o l'accoppiatore per elettrodomestici deve restare prontamente utilizzabile. 17. Il rumore aereo dell'apparecchio non supera i 70 dB (A). 18. L'apparecchio appartenente alla CLASSE I deve essere collegato ad una presa elettrica dotata di messa a terra di protezione. 19. Per ridurre il rischio di incendio o folgorazione, non esponete questo apparecchio alla pioggia o all'umidità. 20. Non tentate di modificare il prodotto. Tale operazione può causare infortuni e/o il guasto del prodotto stesso.21. Utilizzate questo prodotto entro la gamma di temperatura operativa specificata.Questo simbolo indica la presenza di alta tensione all'interno dell'apparecchio, che comporta il rischio di folgorazione.Questo simbolo indica la presenza di istruzioni importanti per l'uso e la manutenzione nella documentazione in dotazione all'apparecchio.10/02/12
IMPORTANTES INSTRUÇÕES DE SEGURANÇA1. LEIA estas instruções. 2. GUARDE estas instruções. 3. PRESTE ATENÇÃO a todas as instruções.4. SIGA todas as instruções. 5. NÃO use este aparelho perto de água. 6. LIMPE SOMENTE com um pano seco. 7. NÃO bloqueie nenhuma das aberturas de ventilação. Deixe distâncias suficientes para ventilação adequada e instale de acordo com as instruções do fabricante. 8. NÃO instale próximo de nenhuma fonte de calor, tais como fogo aceso, radiadores, bocais de aquecimento, fornos ou outros aparelhos que produzam calor (inclusive ampli-ficadores). Não coloque fontes de chamas sobre o produto. 9. NÃO inutilize as características de segurança do conector polarizado ou com pino de aterramento. Um conector polarizado possui duas lâminas com uma mais larga do que a outra. Um conector com pino de aterramento possui duas lâminas e um terceiro pino de aterramento. É fornecida uma lâmina mais larga ou o terceiro pino para a sua segurança. Se por acaso o conector não se encaixar na tomada, chame um eletricista para substituir a tomada obsoleta. 10. PROTEJA o cabo de alimentação, evitando que seja pisado ou que enrosque, especial-mente nos conectores, nas tomadas elétricas de emprego geral e no ponto onde elas saem do aparelho. 11. USE SOMENTE acessórios/apetrechos especificados pelo fabricante.12. USE somente com um carrinho, pedestal, tripé, suporte ou mesa espe-cificados pelo fabricante ou vendidos com o aparelho. Quando utilizar um carrinho, tenha cuidado ao movimentar o conjunto aparelho/carrinho para evitar danos com a queda do mesmo.13. DESLIGUE este aparelho da tomada elétrica durante tempestades com relâmpagos ou quando não seja utilizado por longo período. 14. DEIXE toda a manutenção sob a responsabilidade de uma equipe de manutenção qualificada. É necessário realizar a manutenção quando por algum motivo o aparelho tiver sido danificado de alguma forma, como por exemplo por dano do cabo de alimen-tação elétrica ou do seu conector, por derramamento de líquido ou queda de objetos no aparelho, se o aparelho tiver sido exposto à chuva ou à umidade, não esteja operando normalmente ou tenha sofrido queda. 15. NÃO exponha o aparelho a respingos ou goteiras. NÃO coloque objetos cheios de líquidos, tais como vasos, sobre o aparelho. 16. O plugue MAINS (rede elétrica) ou um acoplador de aparelho deve estar sempre pronto para operação. 17. O ruído aéreo do Aparelho não ultrapassa 70 dB (A). 18. O aparelho com construção CLASSE I deve estar conectado à tomada da rede elétrica com ligação à terra. 19. Para reduzir o risco de incêndio ou choque elétrico, não exponha este aparelho à chuva ou umidade. 20. Não tente alterar este produto. Isso poderá resultar em lesão pessoal e/ou falha do produto.21. Opere este produto dentro da faixa de temperatura de operação especificada.Este símbolo indica que existe nesta unidade tensão perigosa que apresenta risco de choque elétrico.Este símbolo indica que existem instruções operação e manutenção importantes na literatura que acompanha esta unidade.ВАЖНЫЕ ИНСТРУКЦИИ ПО ТЕХНИКЕ БЕЗОПАСНОСТИ1. ПРОЧИТАЙТЕ эти инструкции. 2. СОХРАНИТЕ эти инструкции. 3. ОБРАЩАЙТЕ ВНИМАНИЕ на все предупреждения.4. СЛЕДУЙТЕ всем инструкциям. 5. НЕ пользуйтесь этим прибором вблизи воды. 6. ЧИСТИТЕ ТОЛЬКО сухой тканью. 7. НЕ закрывайте никакие вентиляционные отверстия. Оставляйте расстояния, нужные для достаточной вентиляции, и выполняйте установку в соответствии с инструкциями изготовителя. 8. НЕ устанавливайте вблизи каких бы то ни было источников тепла — открытого пламени, радиаторов, обогревателей, печей или других приборов (включая усилители), выделяющих тепло. Не помещайте на изделие источники открытого пламени. 9. НЕ пренебрегайте защитными свойствами поляризованной или заземляющей вилки. Поляризованная вилка имеет два ножевых контакта, из которых один шире другого. Заземляющая вилка имеет два ножевых контакта и третий, заземляющий, штырь. Более широкий контакт или третий штырь предусматриваются для безопасности. Если вилка прибора не подходит к вашей розетке, обратитесь к электрику для замены розетки устаревшей конструкции. 10. ЗАЩИТИТЕ силовой шнур, чтобы на него не наступали и чтобы он не был пережат, особенно в местах подсоединения к вилкам, розеткам и в месте выхода из прибора. 11. ИСПОЛЬЗУЙТЕ ТОЛЬКО те принадлежности и приспособления, которые предусмотрены изготовителем.12. ИСПОЛЬЗУЙТЕ только с тележкой, стендом, штативом, кронштейном или столом, которые предусмотрены изготовителем или наглухо прикреплены к прибору. При использовании тележки будьте осторожны, когда передвигаете тележку вместе с прибором — переворачивание может привести к травме.13. ОТСОЕДИНЯЙТЕ прибор ОТ СЕТИ во время грозы или если он не используется длительное время. 14. ПОРУЧИТЕ все обслуживание квалифицированному техническому персоналу. Обслуживание требуется при каком-либо повреждении прибора, например, при повреждении шнура питания или вилки, если на прибор была пролита жидкость или на него упал какой-либо предмет, если прибор подвергся воздействию дождя или сырости, не функционирует нормально или если он падал. 15. НЕ допускайте попадания на прибор капель или брызг. НЕ ставьте на прибор сосуды с жидкостью, например, вазы. 16. Вилка электропитания или штепсель прибора должны быть легко доступны. 17. Уровень воздушного шума этого аппарата не превышает 70 дБ (A). 18. Аппараты конструкции КЛАССА I необходимо подсоединять к СЕТЕВОЙ розетке с защитным соединением для заземления. 19. Чтобы уменьшить риск возгорания или поражения электрическим током, не допускайте попадания на этот аппарат дождя или влаги. 20. Не пытайтесь вносить изменения в это изделие. Это может привести к травме и (или) выходу изделия из строя.21. Эксплуатируйте это изделие в указанном диапазоне рабочих температур.Этот знак показывает, что внутри прибора имеется опасное напряжение, создающее риск электрического удара. Этот знак показывает, что в сопроводительной документации к прибору есть важные указания по его эксплуатации и обслуживанию.10/02/12
WICHTIGE SICHERHEITSHINWEISE1. Diese Hinweise LESEN. 2. Diese Hinweise AUFBEWAHREN. 3. Alle Warnungen BEACHTEN.4. Alle Hinweise BEFOLGEN. 5. Dieses Gerät NICHT in Wassernähe VERWENDEN. 6. NUR mit einem sauberen Tuch REINIGEN. 7. KEINE Lüftungsöffnungen verdecken. Hinreichende Abstände für ausreichende Belüftung vorsehen und gemäß den Anweisungen des Herstellers installieren. 8. NICHT in der Nähe von Wärmequellen wie zum Beispiel offenen Flammen, Heizkörpern, Wärmespeichern, Öfen oder anderen Hitze erzeugenden Geräten (einschließlich Verstärkern) installieren. Keine Quellen von offenen Flammen auf dem Produkt platzieren. 9. Die Schutzfunktion des Schukosteckers NICHT umgehen. Ein Schukostecker verfügt über zwei Steckerzinken sowie Schutzleiter. Bei dieser Steckerausführung dienen die Schutzleiter Ihrer Sicherheit. Wenn der mitgelieferte Stecker nicht in die Steckdose passt, einen Elektriker mit dem Austauschen der veralteten Steckdose beauftragen. 10. VERHINDERN, dass das Netzkabel gequetscht oder darauf getreten wird, insbesondere im Bereich der Stecker, Netzsteckdosen und an der Austrittsstelle vom Gerät. 11. NUR das vom Hersteller angegebene Zubehör und entsprechende Zusatzgeräte verwenden.12. NUR in Verbindung mit einem vom Hersteller angegebenen oder mit dem Gerät verkauften Transportwagen, Stand, Stativ, Träger oder Tisch verwenden. Wenn ein Transportwagen verwendet wird, beim Verschieben der Transportwagen/Geräte-Einheit vorsichtig vorgehen, um Verletzungen durch Umkippen zu verhüten.13. Bei Gewitter oder wenn das Gerät lange Zeit nicht benutzt wird, das Netzkabel HERAUSZIEHEN. 14. ALLE Reparatur- und Wartungsarbeiten von qualifiziertem Kundendienstpersonal durchführen lassen. Kundendienst ist erforderlich, wenn das Gerät auf irgendwelche Weise beschädigt wurde, z. B. wenn das Netzkabel oder der Netzstecker beschädigt wurden, wenn Flüssigkeiten in das Gerät verschüttet wurden oder Fremdkörper hineinfielen, wenn das Gerät Regen oder Feuchtigkeit ausgesetzt war, nicht normal funktioniert oder fallen gelassen wurde. 15. Dieses Gerät vor Tropf- und Spritzwasser SCHÜTZEN. KEINE mit Wasser gefüllten Gegenstände wie zum Beispiel Vasen auf das Gerät STELLEN. 16. Der Netzstecker oder eine Gerätesteckverbindung muss leicht zu betätigen sein. 17. Der Luftschall des Geräts überschreitet 70 dB (A) nicht. 18. Das Gerät mit Bauweise der KLASSE I muss mit einem Schukostecker mit Schutzleiter in eine Netzsteckdose mit Schutzleiter eingesteckt werden. 19. Dieses Gerät darf nicht Regen oder Feuchtigkeit ausgesetzt werden, um das Risiko von Bränden oder Stromschlägen zu verringern. 20. Nicht versuchen, dieses Produkt zu modifizieren. Ansonsten könnte es zu Verletzungen und/oder zum Produktausfall kommen.21. Dieses Produkt muss innerhalb des vorgeschriebenen Temperaturbereichs betrieben werden.Dieses Symbol zeigt an, dass gefährliche Spannungswerte, die ein Stromschlagrisiko darstellen, innerhalb dieses Geräts auftreten.Dieses Symbol zeigt an, dass das diesem Gerät beiliegende Handbuch wichtige Betriebs- und Wartungsanweisungen enthält.CONSIGNES DE SÉCURITÉ IMPORTANTES1. LIRE ces consignes. 2. CONSERVER ces consignes. 3. OBSERVER tous les avertissements.4. SUIVRE toutes les consignes. 5. NE PAS utiliser cet appareil à proximité de l'eau. 6. NETTOYER UNIQUEMENT avec un chiffon sec. 7. NE PAS obstruer les ouvertures de ventilation. Laisser des distances suffisantes pour permettre une ventilation adéquate et effectuer l'installation en respectant les instructions du fabricant. 8. NE PAS installer à proximité d'une source de chaleur telle qu'une flamme nue, un radiateur, une bouche de chaleur, un poêle ou d'autres appareils (dont les amplificateurs) produisant de la chaleur. Ne placer aucune source à flamme nue sur le produit. 9. NE PAS détériorer la sécurité de la fiche polarisée ou de la fiche de terre. Une fiche polarisée comporte deux lames dont l'une est plus large que l'autre. Une fiche de terre comporte deux lames et une troisième broche de mise à la terre. La lame la plus large ou la troisième broche assure la sécurité de l'utilisateur. Si la fiche fournie ne s'adapte pas à la prise électrique, demander à un électricien de remplacer la prise hors normes. 10. PROTÉGER le cordon d'alimentation afin que personne ne marche dessus et que rien ne le pince, en particulier au niveau des fiches, des prises de courant et du point de sortie de l'appareil. 11. UTILISER UNIQUEMENT les accessoires spécifiés par le fabricant.12. UTILISER uniquement avec un chariot, un pied, un trépied, un support ou une table spécifié par le fabricant ou vendu avec l'appareil. Si un chariot est utilisé, déplacer l'ensemble chariot-appareil avec précaution afin de ne pas le renverser, ce qui pourrait entraîner des blessures.13. DÉBRANCHER l'appareil pendant les orages ou quand il ne sera pas utilisé pendant longtemps. 14. CONFIER toute réparation à du personnel qualifié. Des réparations sont nécessaires si l'appareil est endommagé d'une façon quelconque, par exemple : cordon ou prise d'alimentation endommagé, liquide renversé ou objet tombé à l'intérieur de l'appareil, exposition de l'appareil à la pluie ou à l'humidité, appareil qui ne marche pas normale-ment ou que l'on a fait tomber. 15. NE PAS exposer cet appareil aux égouttures et aux éclaboussements. NE PAS poser des objets contenant de l'eau, comme des vases, sur l'appareil. 16. La prise SECTEUR ou un coupleur d’appareil électrique doit rester facilement utilisable. 17. Le bruit aérien de l'appareil ne dépasse pas 70 dB (A). 18. L'appareil de construction de CLASSE I doit être raccordé à une prise SECTEUR dotée d'une protection par mise à la terre. 19. Pour réduire les risques d'incendie ou de choc électrique, ne pas exposer cet appareil à la pluie ou à l'humidité. 20. Ne pas essayer de modifier ce produit. Cela risque de causer des blessures et/ou la défaillance du produit.21. Utiliser ce produit dans sa plage de températures de fonctionnement spécifiée.Ce symbole indique la présence d'une tension dangereuse dans l'appareil constituant un risque de choc électrique.Ce symbole indique que la documentation fournie avec l'appareil con-tient des instructions d'utilisation et d'entretien importantes. 10/02/12
1 Table of ContentsUser Manual 3IMPORTANT SAFETY INSTRUCTIONS 3SAFETY PRECAUTIONS 3CAUTION 3WARNING 3WARNING 3WARNING 3System Overview 4General Description and Features 5Theory of Operation 6Groups and Audio Channels 6Network 6Wireless Audio 6System Setup 8Install and Power the Hardware 9Additional Equipment Requirements 9Rackmount the ANI 9Mount the APT 9Power the Hardware 9Connect the Components to Form a Network 10Single Group System (Automatic Configuration) 10Multiple Group System 10Access the MXW System Interface 11Assign Components to a Group 12Set Up Microphones 13Microphone Placement 15Hardware Interface Description 16Access Point Transceiver (APT) 17Audio Network Interface (ANI) 18Front Panel 18Back Panel 194-Port Network Interface 19Networked Charger (NCS) 20Microphones 21Description 21Microphone Types and Applications 22Microphone States 22Rechargeable Microphone Batteries 23Recharging the Battery 23Monitoring the Battery Information 23Replacing the Battery 23Networking 24Networking Best Practices 25Network Topologies 25Multiple Ethernet Switch Setup #1 25Multiple Ethernet Switch Setup #2 26Multiple Ethernet Switch (Wi-Fi) Setup #3 26Configuring Firewalls for Mac or Windows Operating Systems 27Mac OS Native Firewall 27Windows XP or Vista Firewall 27Windows 7 Firewall 27Configuring Wi-Fi for Wireless Networking 27Troubleshooting 28Factory Reset 28Set Appropriate Latency Settings 28Dedicate a Device for Master Clock 28Software Introduction 29Shure Device Discovery Application 30Opening the MXW GUI 30MXW System Graphical User Interface (GUI) 31GUI Description 31Control Bar 33Inputs/Outputs Tab 33Preferences Tab 33Dante Software by Audinate 34Dante Controller 34Dante Virtual Soundcard 34Optimizing the System 35Site Survey: RF Spectrum Scan 36Performing a Scan 36Setting RF Gain for Installation 37Dynamic RF Power Control 37Manually Setting RF Power 37Adjacent Room Freq. Coordination 37Average Battery Runtime per Power Level 37Removing/Exchanging a Component from the Group 38Firmware Updates 39Troubleshooting 40Audio 40Networking 40Control Software 40Control Command Strings 40Safety Information 41Certifications 41Specifications 4210/02/12
2 10/02/12
3 User ManualIMPORTANT SAFETY INSTRUCTIONS1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventilation and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that pro-duce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particu-larly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use cau-tion when moving the cart/apparatus combination to avoid injury from tip-over.13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is re-quired when the apparatus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this appara-tus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.21. Operate this product within its specified operating temperature range.SAFETY PRECAUTIONSThe possible results of incorrect use are marked by one of the two sym-bols—"WARNING" and "CAUTION"—depending on the imminence of the danger and the severity of the damage. WARNING: Ignoring these warnings may cause se-vere injury or death as a result of incorrect operation.CAUTION: Ignoring these cautions may cause moder-ate injury or property damage as a result of incorrect operation.CAUTION• Never disassemble or modify the device, as failures may result.• Do not subject to extreme force and do not pull on the cable or failures may result.• Keep the product dry and avoid exposure to extreme temperatures and humidity.WARNING• If water or other foreign objects enter the inside of the device, fire or electric shock may result.• Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.This device is able to produce sound volume higher than 85 dB SPL. Please check your maximum allowed continuous noise exposure level based on your national employment protection requirements. WARNINGLISTENING TO AUDIO AT EXCESSIVE VOLUMES CAN CAUSE PERMANENT HEARING DAMAGE. USE AS LOW A VOLUME AS POSSIBLE. Over exposure to excessive sound levels can damage your ears resulting in permanent noise-induced hearing loss (NIHL). Please use the following guidelines established by the Occupational Safety Health Administration (OSHA) on maximum time exposure to sound pressure lev-els before hearing damage occurs. 90 dB SPL at 8 hours95 dB SPL at 4 hours100 dB SPL at 2 hours105 dB SPL at 1 hour110 dB SPL at ½ hour115 dB SPL at 15 minutes120 dB SPL Avoid or dam-age may occurWARNING• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), or incinerate• Follow instructions from manufacturer• Never put batteries in mouth. If swallowed, contact your physician or local poison control center• Do not short circuit; may cause burns or catch fire• Do not charge or use battery packs with other than specified Shure products• Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the likeWARNING: Danger of explosion if battery incorrectly replaced. Operate only with Shure compatible batteries.Note: Use only with the included power supply or a Shure-approved equivalent. IMPORTANT SAFETY INSTRUCTIONS1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-tion and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.21. Operate this product within its specified operating temperature range.This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte-nance instructions in the literature accompanying this unit. WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.IMPORTANT SAFETY INSTRUCTIONS1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-tion and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or groundingtype plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.21. Operate this product within its specified operating temperature range.This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte-nance instructions in the literature accompanying this unit. WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.10/02/12
4System OverviewSystem Overview10/02/12
5System OverviewGeneral Description and FeaturesThe Microflex Wireless Series (MXW) is a complete solution for meeting room and presentation applications. Developed with Audinate's Dante technology, the system routes digital audio over standard IP equipment across a network of access points, digital-to-analog converters and computers. Access points mount to a ceiling or wall to communicate wirelessly with the microphones, distributing audio to the Dante network. RF coordination is automatic and continuous, offering worry-free wireless audio transmission for up to 32 channels.Dante Digital Audio NetworkingDigital audio is carried over standard Ethernet using shielded Cat5e (or higher) cables. Dante provides low latency, tight clock synchronization, and high Quality-of-Service (QoS) to provide reliable audio transport to a variety of Dante devices. Dante audio can coexist safely on the same network as IT and control data, or can be configured to use a dedicated network.EncryptionThe MXW transmits secure, encrypted audio using Advanced Encryption Standard (AES-256), which conforms to the US Government National Institute of Standards and Technology (NIST) publication FIPS-197.Automatic Frequency CoordinationThe MXW Series uses automatic frequency coordination to achieve worry-free, solid wireless communication. Frequencies are shared and time-divided between multiple transmitters. A highly accurate time-sync allows multiple APTs to work together for up to 32 channels of wireless transmitters.Microphones are assigned to channels by arranging them in the charger and pressing the link button. The APT assigns the microphones to a channel according to the charger slot number.Remote Control and MonitoringThe system can connect to a computer or 3rd party control system (AMX, Crestron, Extron, etc) for remote control and monitoring. The web browser-based graphical user interface (GUI) enables RF spectrum management, audio routing, and microphone behavior.Rechargeable MicrophonesThe MXW series microphones feature an internal rechargeable battery. Microphones charge directly in the charger without the battery removal. During a charging cycle, the GUI displays battery information (battery runtime, charge cycle count and battery capacity). Up to xx hours of continuous use.Built-In RF Spectrum ScannerThe MXW APT has the ability to scan the entire RF spectrum for a duration of time. The scan provides an accurate xx insight xx to a location's spectrum availability during typical event hours.Shure Legendary Audio Quality10/02/12
6System OverviewTheory of OperationGroups and Audio ChannelsThe MXW system uses Groups to organize the audio and control data transport between components. Each Group is comprised of a single access point, charger(s) and audio output device(s). Groups have four or eight channels, depending on the access point model. Once the group is formed, microphones can be linked to the channels from the charging station. Each slot on the charging station corresponds to channels in the group.Automatic GroupDante's self-discovery feature enables a Group to automatically form when the network is comprised of a single APT, ANI and charger. These components must be the same channel count for the automatic association to occur (forming a group of 4 or 8 channels). Setup through the GUI is not necessary for this configurationNetworkThe network is core communication pathway of the MXW system. It transports Dante digital audio with Shure control data over standard IP/Ethernet equipment. When an MXW device joins the network, it automatically configures to compatible IP settings.Gigabit Switch with DHCPFor systems with more than eight channels, a gigabit switch is required to create a network of additional access points, chargers and audio output devices. Connecting all components on the same network will ensure the most reliable RF management and digital clock synchronization.In some cases, computer settings or programs may interfere with the network. The majority of these connection issues can be solved by using a DHCP-enabled router. Most routers include a DHCP server, while switches do not.Wireless AudioMXW microphones transmit digital audio in the DECT In the US, wirelesss audio transmits in the unlicensed 1920-1930 MHz frequency band10/02/12
7System OverviewThe following is an overview of each component and its function in the MXW system:NetworkINPUT: SPLOUTPUT: Headphonepowerethernetnetwork audiolockout-18-240-6-12lineauxmicmutesig/cliplineauxmutesig/clipAudio Network InterfaceHEADPHONE-18-24-30-36-48-60-9 0INPUT OUTPUTpush to solo | hold to mute adjustA B 1 2 3 4 5 6 7 878651234APTNCSGUIANI①② ③ ④ ⑤① MXW Microphones•Convert audio into a digital RF signal that transmits wirelessly to the APT.•Available in a variety of form factors to accommodate any event.•Boundary and gooseneck models feature a headphone jack for monitoring audio from the network.② Access Point Transceiver (APT)•Transports encrypted, wireless audio between the microphones and the Dante network.•Maintains stable audio transmission through advanced interference detection and automatic frequency coordination.•Requires only a single Cat5e cable for power (via PoE), system time-sync management, and the communication of networked audio and control data.•Hosts the web browser-based GUI for remote system management.③ Audio Network Interface (ANI)•Converts 24-bit/48k digital audio from the network into analog direct outputs. •Four-port gigabit switch enables the ANI to be the networking hub of an eight-channel MXW system.•Network Port 4 (Uplink) can be configured to restrict audio and provide protected data uplink to a corporate network.•Input channels add audio to the network for monitoring at the microphone headphone output.Note: The ANI can be substituted with the Shure SCM820 Digital IntelliMix Mixer.④ Networked Charging Station (NCS)•Recharges microphone batteries by connecting to the USB port of the microphone.•Links up to eight microphones at a time to channels in a group.•Transmits detailed battery information to the network.•LEDs display microphone battery charge status.⑤ Graphical User Interface (GUI)The MXW System is managed from the graphical user interface (GUI). The computer must be networked to the APT to access the GUI from a web browser. Use the software interface for the following system functions:•Assign components to groups to determine the routing of digital audio and control data.•Perform an RF spectrum scan to accurately survey a site's spectrum activity over a duration of time.•Monitor microphone battery statistics during the charge.•Control microphone activity state, gain setting and EQ filters.•Customize the function of LED and mute/active button of the microphone.•Configure IP settings.10/02/12
8System SetupSystem Setup10/02/12
9System SetupInstall and Power the HardwareAUX INMASTERlockoutpowerethernetnetwork audioautomix linkdual mixerLIMAB-9-18-24-36-48-600gainlimiterL+R SUMgainlow cuthi shelfmeterpush to solo | hold to mute1 2 3 4 5 6 7 8ABHEADPHONERackmount the ANIUse the screws and washers supplied in the Hardware Kit to mount the ANI.Mount the APT① Position the Access PointThe access point contains multiple directional antennas to provide steady, reliable wireless communication. The cardioid radiation pattern is strongest from the top of the face plate.Use the following guidelines when mounting the access point:•Direct the antenna toward the intended coverage area.•Position access point so there is nothing obstructing a line of sight to the microphones. •Keep antennas away from large metal objects.•Mount access points at least four feet apart. Important: Always perform a "walk around" test to verify coverage before using a wireless system during a speech or performance. Experiment with antenna placement to find the optimum location. If necessary, mark "trouble spots" and ask presenters or performers to avoid those areas. ② Mount the UnitSecure the unit to a ceiling or wall using the supplied mounting screws.Power the Hardware① ANIConnect the IEC power cable from the back panel to an AC power source. Turn on the power switch.② APTThe APT requires PoE to operate. Use a Cat5e cable to connect the APT to the ANI port 1 or to a gigabit switch with PoE. There is no power switch.③ ChargerConnect the PS45 external power supply from the charger to an AC power source. Turn on the power switch.④ Gigabit Ethernet Router or SwitchConnect the router or switch to an AC power source. Turn on the power switch.21Additional Equipment Requirements ① Network CablesEnsure all network cables are shielded Cat5e or higher and do not exceed 100 m between network devices.② Audio CablesReference the guide supplied with the MXWANI Hardware Kit to assemble the output cables to the connectors and strain relief tabs.③ Gigabit DHCP RouterDHCP routers provide the most reliable networking hub for the system.++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1uplin k234Class 0 Po E1Class 0 Po E1②①②③①786512347865123415V 0.6Apower④③LinkPower10/02/12
10System SetupConnect the Components to Form a NetworkThe following are two setup examples for the MXW system. See Networking section for more details on Dante digital audio and networking best practices.Single Group System (Automatic Configuration)Use a Cat5e cable to connect the charger and APT to one of four ports of the ANI network interface. Reference the table for connecting to the ports:Port To Component① Port 1 (PoE) APT② Port 2 Charger④ Port 4 (Uplink) Computer (optional)Requirements: • Cat5e(orhigher)ShieldedEthernetCables(≤100m)++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1uplin k234Class 0 Po E1Class 0 Po E1②①②③①786512347865123415V 0.6Apower④③LinkPowerSingle-Group SystemMultiple Group SystemFollow these steps for connecting a multiple-group system:1. Connect a DHCP enabled router to a computer.2. Connect each charger and audio output device to the router with network cables3. Connect each access point to the network via a PoE source.Requirements: • Cat5e(orhigher)ShieldedEthernetCables(≤100m)• Gigabit Ethernet switch (DHCP-enabled router recommended)• ComputerFour-Group System++++++++ ++www.shure.comMXWANI8M XW AN I8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplinkInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E178651234786512347865123478651234ON OFFDHCPON OFFDHCPON OFFDHCPPoE10/02/12
11System SetupAccess the MXW System InterfaceThe MXW System is controlled and monitored on a graphical user interface (GUI) that opens in a web browser. The computer must be networked to the APT to access the GUI.1. Load and install the Discovery Application. This automatically installs the required Bonjour device discovery tool to the computer.2. Launch the application. The app displays all Shure devices on the network.3. Select and open the APT.The MXW System Interface opens in a web browser.4. Bookmark the device's DNS name.The DNS name is used to access the interface without the Discovery App.MXWANI8 mxwani-aa1.local 192-168-200-22 yesANI1MXWAPT8 mxwapt8-ffe761.local 192-168-200-23 yesConference1NameModel DNS name IP Address Dantemxwani-aa1.local 192-168-200-22ANI 1mxwapt8-ffe761.local 192-168-200-23APT 1Name DNS name IP Address10/02/12
12System Setup1. Select an APT for Group 1The pop-up menu will display all APTs on the network. This determines if the group has four or eight channels (APT4 or APT8).2. Select the charger(s). When using gooseneck microphones, it is necessary to use two chargers for 8 microphones. (Gooseneck microphones take up front and back slots.)3. Select the Audio Output Device(s). This can be an ANI4, ANI8 or SCM820 IntelliMix® Mixer.id? Button flashes the LEDs of the selected device for easy identification during setup.Assign Components to a GroupComponents must be assigned to a group to form the communication link of audio and control data. On the Configuration tab, select the following components to form a group of up to 8 channels:10/02/12
13System SetupSet Up Microphones1. Arrange microphones in the charger.Microphones are linked to channels according to the arrangement in the charger.Charger Slots Correspond to ChannelsConnecting the Microphone to the Charger SlotFor gooseneck mics2. Link the microphones to channels.The Link procedure can be done from two places:•Charger: Press and hold the Link button for 6 seconds. The LEDs flash during the process and turn solid green once the link is successful.•GUI: From the Configuration page, press the Link button in the group row.For bodypacks, handhelds and boundary mics.78651234 2 3 4 5 6 7 8 1LinkPowerLinkPower 2 3 4 178651234link78651234LinkPower786512348-Channel Charger (NCS8)4-Channel Charger (NCS4)10/02/12
14System Setup3. Remove mics from the charger.The microphone status LEDs will flash, and will remain steady once the audio is ready.++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1++++++++ ++www.shure.comMXWANI8M XW AN I8uplin kInput: 100-240V ~ 1A max. 50/60 Hz234Class 0 Po E1uplin k234Class 0 Po E1Class 0 Po E1②①②③①786512347865123415V 0.6Apower④③LinkPower4. Set mic gainMic gain is adjusted on the Monitor tab of the GUI.Monitor TabSignal indicatorGain adjustment10/02/12
15System SetupMicrophone PlacementFor best low-frequency response and rejection of background noise, place the microphone on a large, flat surface, such as a floor, table, or lectern.To reduce reverberance, avoid reflective surfaces above or to the side of the microphone, such as beveled sides of pulpits or overhanging shelves.10/02/12
16Hardware Interface DescriptionHardware Interface Description10/02/12
17Hardware Interface Description① Power LEDIlluminates green when Power over Ethernet (PoE) is provided.② Network Audio LED•Solid Green: Sending or receiving a digital audio signal.•Flashing Green: Cannot establish a connection.③ RF Link LEDColor StatusGreen ≥1linkedmicrophoneispoweredonintheActive or Mute state.Solid Yellow ≥1linkedmicrophoneisintheStandbyorOffstate.Flashing Yellow The ID button in the GUI has been pressed.Solid Red Problem with RF connection ???Flashing Red No microphones are linked to the unit.④ Reset ButtonPress and hold the reset button for 10 seconds to hard reset the MXW system to factory default settings.Note: Performing a reset will delete system configurations made in the GUI, including device association and microphone link.⑤ Ethernet JackConnects a Cat5e (or higher) cable to a PoE source and the network.⑥ Network Status LED (Green)Off = no network linkOn = network link establishedFlashing = network link active⑦ Network Speed LED (Amber)Off = 10/100 Mbps On = 1 Gbps⑧ Cable Routing PathRoutes the Ethernet cable to enable a flush-mount to the surface.③④⑤⑥⑦⑧①②Access Point Transceiver (APT)10/02/12
18Hardware Interface DescriptionAudio Network Interface (ANI)Front Panel① Input ChannelsAdds analog line- or aux-level signals to the digital network. When associated to the APT, inputs are automatically routed to linked microphone channels (Input A to channels 1-4; Input B to 5-8). Typical applications include sending translated audio or a mix for personal monitoring at the microphone headphone jack. ② Output ChannelsSends analog audio out from the digital audio network. When connected to the MXW system, the outputs are automatically routed from the associated MXWAPT. ③ Channel Select ButtonSelects a channel and performs the following functions: Action FunctionSingle Press•Listen to the channel at the headphone jack•Display and adjust channel gain•Monitoroutputsignallevelonthe⑪LevelMeterPress and Hold (3 seconds)Mute/unmute a channel. Mute is indicated by the⑥MuteLED.④ Selected Channel LEDIlluminates when a channel is selected. ⑤ Signal Strength LED (sig/clip)Indicates audio signal strength for each channel:Green = NormalAmber = StrongRed = Clipping (to eliminate clipping, attenuate the signal level at the audio source)⑥ Mute LEDIlluminates red when the Channel Select button is held for 3 seconds, muting the channel. A muted channel is still routed to the HEADPHONE jack for monitoring or troubleshooting.⑦ Input Level Select ButtonsSet the selected channel to line- or aux-level to match the input signal.⑧ Output Level Select ButtonsSet the selected channel to an output level that matches the connecting device:line: +4 dBUaux: −10dBVmic: −30dBV⑨ Output Gain ControlUse the up/down buttons to adjust the channel gain attenuation from 0 dB (no attenuation) to -24 dB. ⑩ Output Gain SettingDisplays the attenuation made from the Output Gain Control.⑪ Level MeterDisplays a selected channel’s audio level in dBFS. It is good practice to use -18 dBFS on the output meter as an approximation of 0 VU on an analog meter.⑫ Hardware Status LEDsIlluminate to indicate the status of the hardware: powerethernetnetwork audiolockout-18-240-6-12lineauxmicmutesig/cliplineauxmutesig/clipAudio Network InterfaceHEADPHONE-18-24-30-36-48-60-9 0INPUT OUTPUTpush to solo | hold to mute adjustA B 1 2 3 4 5 6 7 8③③④ ④⑤ ⑤⑥⑥⑦ ⑧ ⑨⑩ ⑪ ⑫ ⑬ ⑭①②LED Color Statuspower Green Unit is powered on. Ethernet Green Connected to an Ethernet device. network audioGreen Sending or receiving a digital audio signal. Flashing Green Cannot establish a connection.lockout RedFront panel gain and mute controls are locked. The LED will blink when a button is pressed while the hard-ware is locked. A channel can still be selected for headphone monitoring.⑬ Headphone Volume KnobAdjusts the volume to the headphone output.⑭ Headphone Output1/4” (6.35 mm) output jack for monitoring a selected channel.10/02/12
19Hardware Interface DescriptionMXWANI8Input: 100-240V ~ TBD A max. 50/60 Hz Class 0 PoEuplink1234MXWANI8Input: 100-240V ~ TBD A max. 50/60 HzClass 0 PoEuplink1234①②③④⑤ ⑥ ⑦⑧① AC Power IEC connector 100 - 240 V AC.② Power SwitchPowers the unit on or off.③ Output Block Connectors (1-8)Three-pin, low-voltage connector provides a direct output for each channel.④ Chassis GroundUse to directly ground the cable shield to the chassis.⑤ Input Block Connectors (A,B)Three-pin, low-voltage connector adds line- or aux-level analog signals to the digital network. Back Panel⑥ Reset ButtonPress and hold the button for five seconds to reboot the device with factory default settings. ⑦ Network Status LED (Green)Off = no network linkOn = network link establishedFlashing = network link active⑧ Network Speed LED (Amber)Off = 10/100 Mbps On = 1 Gbps⑨ Network InterfaceDigital Audio connection and networking capabilities with shielded Cat-5e (or higher) cable. ⑨4-Port Network InterfacePort DescriptionPort 1 (PoE) Provides Power over Ethernet (PoE) for the Shure MXWAPT Access Point.Ports 2 and 3Connects to an additional ANI for clock syn-chronization, to an MXW charger, or to a con-trol system.Port 4 (Uplink)By default, this port functions the same as ports 2 and 3. However, it can be configured to provide password protected uplink to corporate LAN without network audio traffic. When Port 4 Uplink is enabled from the GUI, it only provides access to the GUI, blocking data to the Shure Discovery Application, Dante Controller and Dante Virtual Soundcard. 10/02/12
20Hardware Interface Description① Charging Slots (USB 2.0 Type A Plug)Store, recharge and link microphones in the USB slots. Slots are associated to channels in an APT according to the system setup in the GUI.② Power LEDIlluminates when the unit powered on.③ Link LEDIlluminates after a successful link.④ Link ButtonPress and hold for 10 seconds to link all microphones in the charger to channels of the associated APT.⑤ Battery Status LEDsMonitor microphone battery status during a charge, in increments of 10, 25, 50, 75, 100%⑥ Locking DC Power Supply JackScrew the PS45 power supply to the input, illuminating the POWER LED.⑦ Power Switch Powers the unit on or off⑧ Ethernet PortConnects to the MXW system using a Cat5e (or higher) cable.⑨ Network Status LED (Green)•Off = no network link.•On = sending or receiving digital audio over the network.•Flashing = cannot establish a connection.⑩ Network Speed LED (Amber)•Off = 10 Mbps •On = 100 MbpsNetworked Charger (NCS)78651234 2 3 4 5 6 7 8 1LinkPowerLinkPower 2 3 4 1Charger Slots Correspond to Audio Channels8-Channel Charger (NCS8) 4-Channel Charger (NCS4)78651234LinkPower③④⑤⑥⑦⑧⑨⑩①②10/02/12
21Hardware Interface DescriptionMicrophonesDescription① Power ButtonPress button to turn the microphone on; the microphone LED will flash green and red until turning a solid color (color depends on state specified in GUI). Press and hold for 3 seconds to power off.Note: The bodypack does not have a dedicated power button.② Mute/Active ButtonChanges the microphone state to Active or Mute. Each microphone type can be set to toggle or push-and-hold from the Preferences tab of the GUI. The following describes the function of each setting:•Toggle:Press and release the button to change the status to Active or Mute.•Push-to-talk:Hold button to pass audio.•Push-to-mute:Hold button to mute the audio.③ Microphone State LEDIndicates the microphone state. Pulsing Red = Standby mode; Off = microphone is off.Customize the indication of Active and Mute for each transmitter type from the Preferences tab of the GUI. These options are displayed in the following table:Mute ActiveSolid Red Solid GreenFlashing Red Solid RedSolid Red OffOff Solid RedFlashing Green Solid GreenStandby mode is always represented with a pulsing red LED.④ Low Battery LED (Gooseneck and Boundary only)Gooseneck and boundary microphones only. Color StatusOff >10% battery runtime remainsSolid Red ≤10%batteryruntimeremainsFlashing Red Battery is too low to transmit an RF signal. Recharge the microphone.⑤ Earphone Jack1/8" (3.5 mm) jack for monitoring the return channel signal, such as translated audio.⑥ Charge Connector (USB 2.0 Type A Jack)Connects to the NCS charger slot or to the optional (?? model) USB adapter cable.10/02/12
22Hardware Interface DescriptionMicrophone Types and ApplicationsChoosing a Microphone TypeFor each event, select microphones that will best serve the arrangement of participants and presenters. The following is a chart of each microphone and its primary use:Type Use Placement NotesGooseneck Sits on a desk or podium with an extended neck for close talkingBoundarySits flat on a table or desk to provide coverage for one or two people.BodypackConnects to a lavelier microphone for placement on a speaker's clothing. When no lavalier is con-nected, an internal omnidirectional microphone is activated.Microphone StatesAfter a microphone has been linked to the network, it is in one of four states (or, levels of activity). The follow-ing is a summary of each state:ActiveReady to pass audio to network.MuteAudio is muted.StandbyAudio is muted and the microphone is in a hibernation state to conserve the battery.OffNo connection to the network. The microphone must be turned on using the power button on the mic.Initial States After Removing from ChargerEach microphone type can be assigned to a specified state whenever it is removed from the charger. Go to the Preferences tab of the GUI to set the initial state for each microphone type.When the Initial State is set to Standby, pressing the microphone's mute button will return it to one of two states as defined in the Switch behavior:• Push-to-talk• Active toggleFor example, an installer may prefer to have the handheld microphones exit the charger with a Mute status to avoid transmitting any handling noise to the audience.10/02/12
23Hardware Interface DescriptionRechargeable Microphone BatteriesRecharging the BatteryThere are two ways to recharge the microphone battery:Using the NCS ChargerUse the charger slots to recharge and store the microphones. Handheld, bodypacks, and boundary microphones use the vertical slots; gooseneck mi-crophones use the back horizontal slots.?? Model USB Power AdapterThe USB adapter allows the microphone to charge during operation.Monitoring the Battery InformationCharge to Full IndicatorsWhen the microphone is charging in the NCS charging station, the charger LEDs display battery in increments of 10, 25, 50, 75, 100% For further detail, the Monitor page displays the time to full charge in hours:minutes.Battery Runtime RemainingWhen the microphone is out of the charger, the Monitor tab will display the runtime remaining in hours:minutes.Battery Life StatisticsOn the Utility tab of the GUI, two battery life statistics that are displayed: •% Battery Capacity: Percentage of charge capacity compared to a new battery•Cycle Count: Number of charge cycles logged by the battery.Replacing the BatteryCaution! Danger of exploding if battery is incorrectly replaced. Use only with the same or equivalent type. Use the following guidelines for replacing the battery:1. Unscrew and open the battery door.2. Disconnect the battery from the microphone. Properly dispose of the old battery.3. Plug the new battery to the jack on the microphone. 4. Replace the battery door and screw it shut.MXW microphones feature the Shure rechargeable Lithium-ion battery. Lithium-Ion chemistry and intelligent Shure battery circuitry results in a rechargeable battery with no memory effect. It can be recharged at any time; a complete discharge is not necessary.78651234786510/02/12
24NetworkingNetworkingDante technology uses standard IP over Ethernet and safely coexists on the same network as IT and control data. It provides an integrated solution to transport two types of data over the same network cable: Shure Control, and Dante Audio and Controller. Shure Control: GUI and 3rd Party ControlThe Shure Control carries data for the GUI operation, firmware updates and 3rd party control systems (AMX, Crestron, Extron). This data is transmitted over all MXW components connected to the network.Dante Audio and ControllerThis network carries both the Dante digital audio and the control data for Dante Controller. This data is transmitted between the APT and the ANI.10/02/12
25NetworkingNetworking Best PracticesUse the following best practices when setting up a network to ensure reliable communication:• Always use a "star" network topology• Use only 1 DHCP enabled server per network. Disable DHCP addressing on additional servers• When using an AXT620 Ethernet Switch, turn on the switch first before turning on additional components connected to the network• To expand the network, use multiple Ethernet switches in a star topology• Connect each device directly to the port of an Ethernet switch. Avoid "daisy-chaining" Ethernet port connections between devices for larger networks.• Do not loop network connections• All networked devices must be set to the same subnet mask• All devices must be at the same firmware revision level, with the exception of the AXT620 Ethernet SwitchNetwork TopologiesThere are several ways to configure a network of devices. In general, you should always use a "star" network topology where each device uses one connection to an Ethernet switch port. If multiple switches are used, each switch is individually connected to one connection to the next level of Ethernet switch.Below are three example configurations of large networks of devices.Multiple Ethernet Switch Setup #1• Any AXT620 switch (but only one) can be set as the DHCP server• Each networked device needs an individual connection to the switch• Connect them via any portAXT620 with front panel DHCP switch set to ONServer Client Client AXT620 with front panel DHCP switch set to OFFAXT620 with front panel DHCP switch set to OFFAXT610 ShowLink Access Point 10/02/12
26NetworkingMultiple Ethernet Switch Setup #2Each networked device needs an individual connection to the switch.AXT620 with front panel DHCP switch set to ONServer Client Ethernet Switch AXT610 ShowLink Access Point Multiple Ethernet Switch (Wi-Fi) Setup #3Each networked device needs an individual connection to the switch.Wi-Fi Router (DHCP enabled) Server Client Client AXT620 with front panel DHCP switch set to OFFAXT620 with front panel DHCP switch set to OFFAXT610 ShowLink Access Point 10/02/12
27NetworkingConfiguring Firewalls for Mac or Windows Operating SystemsMac OS Native Firewall1. Open System Preferences.2. Select Security, and then select the Firewall tab.3. To enable editing, make sure the lock icon at the bottom of the window is unlocked before entering your password.4. If the firewall is on, select Advanced. For each of the following applications, select "Allow Incoming Connections":• Wireless Workbench 6.app• slpd• snetDameon• acnproxyWindows XP or Vista Firewall1. From the Start menu, select Control Panel.2. Select Windows Firewall.3. In the Windows Firewall window, if the firewall is set to On, select the Exceptions tab and add the following applications to the exceptions list:• WWB6.exe• SLPD.exe• SNETDAMEON.exeWindows 7 Firewall1. From the Start menu, select Control Panel.2. Select Systems and Security.3. Select Windows Firewall.4. Select Allow a program or feature through Windows Firewall.5. To view the list of applications, select Change Settings.6. Select the following applications to allow them:• WWB6.exe• SLPD.exe• SNETDAMEON.exeConfiguring Wi-Fi for Wireless NetworkingWhen using Wireless Workbench over Wi-Fi, it’s important to set up the wireless router properly for best performance. Wireless Workbench employs ‘multicast’ data protocols to communicate to the Axient and PSM1000 devices. Wi-Fi treats broadcast and multicast packets differently than general packets for backward compatibility reasons. In some cases, the Wi-Fi router will limit the multicast packet transmission rate to a value that is too slow for Wireless Workbench to properly operate.By default, most Wi-Fi routers are configured to operate in ‘b/g-mode’, which tells the router to allow both 802.11g and older 802.11b devices to operate over the network. In this configuration, some routers will automatically limit the multicast data rates (or sometimes referred to as ‘basic rate’, or ‘management rate’) to 1-2Mbps. For small wireless microphone configurations of less than 20-30 channels, this Wi-Fi setting should not cause any problems with Wireless Workbench.Tip: For larger wireless microphone configurations of greater than 30 channels, it’s recommended to configure the Wi-Fi router to operate in ‘g-mode’ only. Most routers will increase the multicast transmission rate to 6Mbps when operating in ‘g-mode’ thereby providing adequate bandwidth to Wireless Workbench.Important: For best performance, use a Wi-Fi router that does not limit the multicast rate to 1-2 Mbps.Shure recommends the following Wi-Fi router brands:• Cisco• Linksys• Apple10/02/12
28NetworkingTroubleshootingFactory ResetIf a device isn't appearing on the network, perform a hard reset to return the device to default settings. Factory default settings are designed for automatic com-patibility with other Shure networked devices.Use following instructions to reset each device:Access Point TransceiverPress and hold the reset button for 10 seconds. The network audio status LED will briefly turn off to indicate the unit is rebooting.Note: Factory resets delete system configurations made in the GUI, including device association and microphone linking.Audio Network InterfacePress and hold the reset button for 5 seconds. The front panel LEDS will flash to indicate the unit is rebooting.Networked Charging StationPress and hold the link button while powering up the charger. Continue to hold the link button for 10 seconds. The LEDs will flash to indicate the unit is rebooting.Set Appropriate Latency SettingsLatency settings determine the amount of time that a device can spend processing data packets. When a receiver is overloaded with traffic, audible clicks and pops may occur. Increasing the latency setting will improve performance for large networks.Number of Switch Hops*Recommended Latency Setting* Each device is represents one switch hop.Dedicate a Device for Master ClockDante uses the IEEE 1588 Precision Time Protocol (PTP) to automatically determine a single access point to act as the master clock for the network. This is typically the first APT that connects to the network (if several connect simultaneously, the master defaults to the APT with the lowest MAC address). The remain-ing Dante audio components slave to the masterWhen a master device shuts down or goes offline, the system will automatically begin selecting another master. During this selection time (up to xx seconds), the entire system will NOT pass audio.If the network or building management requires that devices are periodically shut down, you can manually select an access point as the Preferred Master device from Dante Controller software. This allows the installer to set up the system to ensure that the master access point never shuts down during events.10/02/12
29Software IntroductionSoftware IntroductionMXW hardware networks to a computer to operate with several software programs, augmenting the system with additional features and comprehensive remote management.The following software components are used with the MXW series:• Shure Device Discovery Application: Uses Bonjour networking technology to display all Shure devices on the network that include a graphical user interface (GUI).• MXW Series GUI: Hosted from the APT webserver and accessed from a typical web browser, this GUI is used to manage the network of MXW components.• MXWANI GUI: Hosted from the ANI webserver and accessed from a typical web browser, this GUI is used to monitor the ANI's analog inputs/outputs and network configuration.• Dante Controller: Dante Controller (DC) is a free software by Audinate that is used to configure and manage a network of Dante devices. • Dante Virtual Soundcard: An audio driver used to monitor and record digital audio without additional equipment. 10/02/12
30Software IntroductionShure Device Discovery ApplicationThe Device Discovery application finds all Shure devices on the same network that have an embedded web server. These devices network with a computer to access the The Discovery app is included on the CD-Rom supplied with the APT and can be downloaded from the Shure website.Device Discovery with Bonjour: Bonjour software is bundled with the installation of the Shure Device Discovery application. Bonjour technology provides zero configuration networking, allowing devices to automatically discover each other and configure to compatible settings.Opening the MXW GUITo access the MXW system GUI, follow these steps:1. Load the Shure Device Discovery CD to a computer and install the application. Bonjour will install automatically to the computer.2. Connect the PC to the same network as the APT.3. Turn off the PC's WiFi to force the wired network interface.4. Open the Discover app to view all Shure devices on the network.5. Double-click on a unit to open its GUI in a browser.Note: When Port 4 Uplink mode is enabled on the ANI, the Discovery app will not find the GUI. However, the GUI can still be opened by the bookmark or manually typing in the DNS name into the browser.Recommended: Bookmark the GUIThe Discovery app uses Bonjour technology to open a device's GUI using its DNS name (Domain Name System). The DNS name is unique for each device and will never change (unlike IP addresses). Bookmark the GUI using the DNS name allows reliable access to the GUI without going through the Device Discovery app.10/02/12
31Software IntroductionMXW System Graphical User Interface (GUI)A graphical user interface (GUI) is software that allows comprehensive system control and monitoring from a computer. It is hosted from an embedded server built into the APT, and is accessible when properly networked to a computer or 3rd party control device. All hardware functions can be adjusted using the GUI.GUI DescriptionThe following is a description of each tab of the GUI:Monitor Tab① APT SelectionSelects an APT for monitoring channel and RF spectrum information.② Spectrum MeterDisplays the RF spectrum availability from a scan from the APT. See Spectrum Scan section for more details.③ Global Mic ControlControls the status of all microphones linked to the APT.④ Microphone NameMicrophone names can be customized with up to 31 any characters in length except '=','.' or '@'.⑤ Identify ButtonWhen clicked, this commands the microphone to beep and its LED to flash. Microphones must be removed from the charger for this function.⑥ Battery StatusWhile charging: Displays the remaining time until the microphone battery is fully charged.Not charging: Displays the remaining battery runtime of the microphone.⑦ RF Signal Strength⑧ Audio Input MeterIndicate the average input signal level.LED Audio Signal Level DescriptionRed (6) -0.1 dBFS Overload Yellow (5) -6 dBFS Normal peaksYellow/ Green (4) -12 dBFSGreen (3) -20 dBFSSignal PresentGreen (2) -30 dBFSGreen (1) -40 dBFS⑨ Mic GainAdjusts microphone gain from -25 dB to +15 dB gain in 1 dB steps.⑩ High Pass FilterEngages a 6 dB-per-octave filter below 150 Hz for attenuating undesired low frequencies, sometimes caused by table vibrations or air-conditioning rumble.⑪ Low Pass FilterEngages a 6 dB-per-octave filter above 15 kHz for attenuating undesired high frequencies, sometimes caused by sibilant vocals or paper rustling.⑫ Microphone StateMicrophones are in one of four states: •Active: Microphone is on and passing audio to the network.•Mute: Microphone is on but the signal is muted.•Standby: Conserves battery charge and allows the GUI to change the state to Active or Mute.•Off (Inactive): The microphone is powered off. A microphone in this state cannot be controlled by the GUI (it can only be turned on using the power button on the mic). ⑬ Microphone TypeDisplays the microphone type:•Gooseneck•Bodypack•Boundary•Handheld⑭ Return ChannelsMonitor the signal level and mute/unmute the audio of the return channel.③④⑤⑥⑦⑧⑨⑩⑪⑫⑬⑭①②10/02/12
32Software IntroductionPreferences Tab① Switch BehaviorCustomize the switch for each microphone type.•Toggle: Press and release the button to change the status to Active or Mute.•Push-to-talk: Hold button to pass audio.•Push-to-mute: Hold button to mute the audio.•Disabled: The button does not affect the audio.② Initial State from ChargerAssigns the initial state for each microphone type after removal from the charger:•Active: Microphone is on and passing audio to the network.•Mute: Microphone is on but the signal is muted.•Standby: Conserves battery charge and allows the GUI to change the state to Active or Mute.•Off (Inactive): The microphone is powered off. A microphone in this state cannot be controlled by the GUI (it can only be turned on using the power button on the mic). ③ LED BehaviorSet the behavior of the mute/active LED for each microphone type:Mute ActiveSolid RedSolid GreenFlashing RedSolid RedSolid Red OffOff Solid RedFlashing GreenSolid GreenStandby mode is always represented with a pulsing red LED.④ Mute Preference•Local Mute - Individual: Each microphone is muted individually.•Local Mute - All: All microphones mute when any microphone is muted.•External Mute: Microphones are muted by a 3rd-party control device.⑤ RF Power MaxDetermines the maximum distance that an APT will transmit.•Low: ??'•Medium: ??'•Medium High: ??'•High: ??'⑥ Out of Range Alarm⑦ Back in Range Action⑧ Linking Preference⑨ Language⑩ Save/Load Preferences⑪ Password Setup⑫ Register the Product LinkConguration Tab① Device ListCustomize the switch for each microphone type.② Device NameDevice names can be customized with up to 31 any characters in length except '=','.' or '@'.③ Network Interface SelectionDetermines which network interface's IP settings are displayed.•Control: •Network Audio: ④ IP ModeSets IP mode of the selected network interface:•Auto (DHCP): For automatic DHCP or Link-Local IP addresses.•Manual (Static): For Static IP addresses.⑤ IP SettingsDisplays the IP Address, Subnet Mask, and Gateway for each network interface.⑥ MAC AddressThe network interface's unique identification.⑦ Group RowAssign APTs, chargers, and audio output devices to form each group. ⑧ id? ButtonCommands the selected device's LEDs to flash for easy identification.⑨ Link ButtonLinks microphones to channels for the selected charger.Utility Tab① ExportExports the data table to a text file that can be saved to a computer.② GroupIndicates to which group the device is assigned/linked.③ DeviceThe device type or microphone channel.④ TypeThe device model number.⑤ NameDisplays name as defined in ______??⑥ IP Address ControlDisplays the IP Address of the control network interface (Shure GUI control).⑦ IP Address Network AudioDisplays the IP Address of the Network Audio network interface (Dante audio and control).⑧ S/NDisplays the device's serial number.⑨ % Battery CapacityPercentage of charge capacity compared to a new battery.⑩ Cycle CountNumber of charge cycles logged by the battery.⑪ Current VersionDisplays the device's firmware version.10/02/12
33Software IntroductionControl Bar① Identify ButtonThis button sends a command to the hardware to flash front-panel LEDs for easy identification.② Log OffLogs the user out of the GUI. This appears only when a password has been set for Admin or Tech level.③ Language SelectionSelects the language for the GUI. This setting will be saved to the computer.Inputs/Outputs TabInputs (Return Channels)① Channel NameChannel name is customizable by clicking in the text box. Names can be up to 12 characters long. ② Input Gain Setting (A, B)Sets the analog input gain level.③ Audio MeterDisplays input audio levels prior to the analog-to-digital converter.④ Mute ButtonMutes or unmutes the channel's audio. The button illuminates red when a channel is muted.Outputs (1-8, or 1-4)⑤ Channel NameChannel name is customizable by clicking in the text box. Names can be up to 12 characters long. ⑥ Output GainSets the output gain level.⑦ Audio MeterDisplays output audio levels prior to the digital-to-analog converter.⑧ AttenuationOutput attenuation is adjustable in 1 dB increments.⑨ Mute ButtonMutes or unmutes the channel's audio. The button illuminates red when a channel is muted.Various⑩ Network Audio Status•Green = Sending or receiving a digital audio signal.•Flashing green = Cannot establish a connection.⑪ NotesSave project notes here, such as installation dates or IP information.Preferences Tab① LanguageSelects the language for the GUI when the ANI is in Standalone Network Mode. In Normal mode, this is defined in the APT GUI.② Device Serial NumberDisplays the devices serial number.③ Firmware VersionDisplays the current firmware version of the device.④ Reset ButtonReboots the device with factory default settings.⑤ Register This Product LinkClick to register the device at shure.com to receive product and software updates.⑥ Networking Mode•Normal: Enables automatic Dante channel routing with an APT.•Standalone: Channels must be routed manually with Dante Controller software.⑦ Device NameDevice name is customizable by clicking in the text box. Names can be up to 12 characters long (alphanumeric and a limited set of special characters are allowed). ⑧ Addressing ModeAuto: IP settings are Link-Local or automatically accepted from a DHCP server.Manual: IP settings (IP Address, Subnet Mask, and Gateway) are static and are entered manually.⑨ MAC Address⑩ Port 4 ModeConfigures the Port 4 of the network interface: •Switched (default): Full Ethernet support.•Uplink: Only control data for the GUI is transported. Multicast traffic for Dante and the Shure Device Discovery is restricted.⑪ Front Panel LockoutDisables the front panel controls on the hardware. Channels can still be selected for monitoring at the headphone jack.⑫ PasswordBy default, the GUI has no password or security levels. Setting a password for the Admin will automatically generate a Guest-level logon. An additional, Tech-level logon can be created. The following describes the access rights of each logon type:Admin: Full editing rights. The Admin can enable or disable a Tech-level logon.Tech: Rights are limited to the functions that are also editable from the hardware: gain, mute, solo, and reset.Guest: Monitoring only.10/02/12
34Software IntroductionDante Software by AudinateAudinate software provides additional function and control of the Dante digital audio network. Visit Audinate's website for instructions for download and installation.Dante ControllerDante Controller (DC) is a free software by Audinate that is used to configure and manage a network of Dante devices. Use it to route channels between Dante-enabled devices and to monitor the status of the device, clock, and network. Note: DC software is not required for routing audio within the MXW system. Use caution when us-ing DC, as changing settings may interfere with MXW system functionality.Dante Virtual SoundcardDante Virtual Soundcard (DVS) acts as an audio driver used to monitor and record digital audio without additional equipment. DVS uses a computer's standard Ethernet ports to transmit and receive up to 64 channels from any Dante enabled device on the same network.10/02/12
35Optimizing the SystemOptimizing the System10/02/12
36Optimizing the SystemSite Survey: RF Spectrum ScanThe APT features a scanning tool to survey the RF spectrum prior to the installation. It should be conducted during typical hours of activity to identify the avail-ability of the RF spectrum. The channel count limit will be determined by the availability of clear spectrum.During a scan, the APT turns off all associated microphones in order to survey the spectrum of the room for interference from devices such as cordless phones, walkie-talkies, or intercoms.Performing a ScanThe following steps are used to perform the RF scan:1. Connect the APT and computer to the same network.2. Open the Monitor tab of the GUI and press the Start Scan button.3. Run the scan for the entire time that an event may take place.10/02/12
37Optimizing the SystemSetting RF Gain for InstallationDynamic RF Power ControlBy default, the MXW system automatically adjusts the RF power level based on the distance between an APT and the microphones. This prevents signal dropout if a microphone is taken outside of the radius of the coverage of the current RF level.Note: Greater RF coverage uses more battery power and decreases the battery runtime. Additionally it increases the required distance between systems.RF Level and Coverage AreaLevel 3: 100'Level 2: 50'Level 1: 25'Manually Setting RF PowerYou can limit the RF gain in order to maximize RF efficiency of a fixed space and save microphone battery life.There are three stages of RF gain in the APT for coverage over a range of installation sizes: Level 3: 100' radius, Level 2: 50' radius, Level 1: 25' radius. RF setting affects the microphone battery (higher level uses more power, reducing battery runtime) and the system ability to reuse channels in a space. Using a lower gain level decreases space the needed between systems to avoid conflicting DECT frequency allotment.Adjacent Room Freq. CoordinationAverage Battery Runtime per Power LevelThe following table displays the average runtime of the transmitter for each RF power level:RF Power Level Microphone RuntimeLow ? hoursMedium ? hoursMedium High ? hoursHigh ? hours10/02/12
38Optimizing the SystemRemoving/Exchanging a Component from the GroupTo exchange a microphone, place the new microphone in the charger slot that corresponds to the desired channel. Press and hold the link button for 10 seconds to link the microphone to the channel. The old microphone will no longer be a part of the system and no change will occur for the remaining channels.Important: Always note the charger slot and channel when replacing microphones. The link will immediately override the existing microphone's audio and RF connection to the system. 10/02/12
39Firmware UpdatesFirmware UpdatesFirmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional features and enhancements. To take advantage of design improvements, new versions of the firmware can be uploaded and installed using the Firmware Manager tool. Software is available for download from http://www.shure.com.Perform the following steps to update the firmware for the MXWANI:CAUTION! Ensure the device has a stable network connection during the update. Do not turn off the device until the update is complete. 1. Download Firmware Update Manager from http://www.shure.com and install the software.2. Open the software.3. Click Check Now to view new versions available for download.4. Select the updates and click download.5. Connect the device and computer to the same network. If Port 4 is used, ensure Port 4 Mode is set to Switched mode (default) on the Preferences tab.6. Download the latest firmware to the device.Once the download is complete, the device automatically begins the firmware update, which overwrites the existing firmware.10/02/12
40Firmware UpdatesTroubleshootingAudioNetworkingControl SoftwareControl Command Strings10/02/12
41Firmware UpdatesSafety InformationMXW1Bodypack Microphone Transmitters: These transmitters have been tested and found to comply with international radiation exposure limits set forth for an uncontrolled environment. This equipment is in direct contact with the body of the user under normal oper-ating conditions. These transmitters must not be co-located or operating in conjunction with any other antenna or transmitter.MXW6, MXW8, MXWAPT4, MXWAPT8Tabletop Gooseneck Microphone Transmitters, Tabletop Boundary Microphone Transmitters, Wireless Access Point Transmitters:These mobile transmitters are intended for use at distances greater than 20 centimeters from the human body. These mobile transmitters are exempt from the testing requirements of international radiation exposure standards due to their proximity to the body of the user in their intended use case and their low power output. These mobile transmitters shall be placed or installed at least 20 cm from any person and must not be co-located or op-erating in conjunction with any other antenna or transmitter.Important Product InformationThe equipment is intended to be used in professional audio applications. EMC conformance testing is based on the use of supplied and recom-mended cable types. The use of other cable types may degrade EMC performance. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate this equipment. Please follow your regional recycling scheme for batteries, packaging, and electronic waste.Note: This device is not intended to be connected directly to a public internet network. Information to the userThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.CertificationsThis device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est auto-risée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage ra-dioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.Conforms to electrical safety requirements based on IEC 60065. This product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. The CE Declaration of Conformity can be obtained from Shure Incorporated or any of its European representatives. For contact information please visit www.shure.com The CE Declaration of Conformity can be obtained from: www.shure.com/europe/complianceAuthorized European representative:Shure Europe GmbHHeadquarters Europe, Middle East & AfricaDepartment: EMEA ApprovalJakob-Dieffenbacher-Str. 1275031 Eppingen, GermanyPhone: 49-7262-92 49 0Fax: 49-7262-92 49 11 4Email: EMEAsupport@shure.deMXWNCS4, MXWNCS8Authorized under the FCC verification provision per Part 15b. This Class B digital apparatus complies with Canadian ICES-003. Cet appa-reil numérique de la classe B est conforme à la norme NMB-003 du Canada. Note: See the label located on the bottom side of the charger enclosure for the FCC marking, the CE marking, the C-Tick marking, and the elec-trical ratings. MXW1, MXW2, MXW6, MXW8, MXWAPT4, MXWAPT8Certified under FCC Part 15. FCC: DD4MXW1, DD4MXW2, DD4MXW6, DD4MXW8, DD4MXWAPT4, DD4MXWAPT8.Meets applicable requirements of RSS-213. IC: 616A-MXW1, 616A-MXW2, 616A-MXW6, 616A-MXW8, 616A-MXWAPT4, 616A-MXWAPT8.10/02/12
42Firmware UpdatesSpecifications10/02/12
www.shure.com ©2011 Shure IncorporatedAsia, Pacific:Shure Asia Limited22/F, 625 King’s RoadNorth Point, Island EastHong KongPhone: 852-2893-4290Fax: 852-2893-4055Email: info@shure.com.hkUnited States, Canada, Latin America, Caribbean:Shure Incorporated5800 West Touhy AvenueNiles, IL 60714-4608 USAPhone: 847-600-2000Fax: 847-600-1212 (USA)Fax: 847-600-6446Email: info@shure.comEurope, Middle East, Africa:Shure Europe GmbH Jakob-Dieffenbacher-Str. 12,75031 Eppingen, GermanyPhone: 49-7262-92490Fax: 49-7262-9249114Email: info@shure.de10/02/12

Navigation menu