Shure orporated ADX2FDG57 Digital Transmission System User Manual Exhibit D Users Manual per 2 1033 b3

Shure Incorporated Digital Transmission System Exhibit D Users Manual per 2 1033 b3

Contents

Exhibit D Users Manual per 2 1033 b3

ADX2FD Axient Digital Handheld TransmitterUSER GUIDE© 2017 Shure Incorporated27A36586 (Rev. Preliminary)Printed in U.S.A.AXIENT® DIGITAL
WARNING• Battery packs may explode or release toxic materials. Risk of fire or burns. Do not open, crush, modify, disassemble, heat above 140°F (60°C), orincinerate.• Follow instructions from manufacturer• Only use Shure charger to recharge Shure rechargeable batteries• WARNING: Danger of explosion if battery incorrectly replaced. Replace only with same or equivalent type.• Never put batteries in mouth. If swallowed, contact your physician or local poison control center• Do not short circuit; may cause burns or catch fire• Do not charge or use battery packs other than Shure rechargeable batteries• Dispose of battery packs properly. Check with local vendor for proper disposal of used battery packs.• Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the likeNote: Use only with the included power supply or a Shure-approved equivalent.Please follow your regional recycling scheme for batteries, packaging, and electronic waste.WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm.低功率電波輻射性電機管理辦法第十二條經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。 第十四條低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。IMPORTANT SAFETY INSTRUCTIONS1. READ these instructions. 2. KEEP these instructions. 3. HEED all warnings.4. FOLLOW all instructions. 5. DO NOT use this apparatus near water. 6. CLEAN ONLY with dry cloth. 7. DO NOT block any ventilation openings. Allow sufficient distances for adequate ventila-tion and install in accordance with the manufacturer’s instructions. 8. DO NOT install near any heat sources such as open flames, radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not place any open flame sources on the product. 9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replace-ment of the obsolete outlet. 10. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-nience receptacles, and the point where they exit from the apparatus. 11. ONLY USE attachments/accessories specified by the manufacturer.12. USE only with a cart, stand, tripod, bracket, or table specified by the manu-facturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.13. UNPLUG this apparatus during lightning storms or when unused for long periods of time. 14. REFER all servicing to qualified service personnel. Servicing is required when the ap-paratus has been damaged in any way, such as power supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. 15. DO NOT expose the apparatus to dripping and splashing. DO NOT put objects filled with liquids, such as vases, on the apparatus. 16. The MAINS plug or an appliance coupler shall remain readily operable. 17. The airborne noise of the Apparatus does not exceed 70dB (A). 18. Apparatus with CLASS I construction shall be connected to a MAINS socket outlet with a protective earthing connection. 19. To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. 20. Do not attempt to modify this product. Doing so could result in personal injury and/or product failure.21. Operate this product within its specified operating temperature range.This symbol indicates that dangerous voltage constituting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and mainte-nance instructions in the literature accompanying this unit.
4ADXFD2 Handheld Transmitter ADX series transmitters deliver impeccable audio quality and RF performance, and are equipped with ShowLink® remote control for real-time parameter adjustments and interference avoidance. This transmitter additionally features Frequency Diversity for seamless audio in even the most challenging en-vironments. Light-weight aluminum construction, AA or SB920 rechargeable power options (with dockable charging).Included ComponentsSB920 Shure Rechargeable Battery95A25763Zipper Bag 95B2313Euro-Threaded Adapter 31B1856Swivel Adapter, black 90F4046Choice of (1) of the following Shure microphone cartridges:SM58 (RPW112) KSM9 Nickel (RPW188)BETA 87C (RPW122) BETA 87A (RPW120)BETA 58A (RPW 118) KSM9 Black (RPW184)KSM8 Black (RPW174) KSM8 Nickel (RPW170)KSM9HS Black (RPW186) KSM9HS Nickel (RPW190) Optional AccessoriesRadome Color ID Kit for AD2 WA617MBattery Contact Cover for AD2 WA618Microphone stand adapter WA371Optional Shure microphone cartridges:SM58 (RPW112)SM86 (RPW114)SM87A (RPW116)BETA 58A (RPW118)BETA 87A (RPW120)BETA 87C (RPW122)VP68 (RPW124)KSM9 Nickel (RPW188)KSM9HS Nickel (RPW190)KSM9 Black (RPW184)KSM9HS Black (RPW186)Features Performance• 184 MHz tuning range• Frequency Diversity enables simultaneous transmission on two inde-pendent frequencies to ensure seamless, uninterrupted audio for mis-sion-critical applications. Single carrier mode is available if Frequency Diversity is not required.• 20 Hz to 20 kHz range with flat frequency response• Automatic input staging optimizes gain setting• Diversity ShowLink-enabled for remote transmitter control and automat-ic interference avoidance• AES 256-bit encryption-enabled for secure transmission• >120 dB, A-weighted, System Gain @ +10• Dante Output: >130dB, A-weighted, System Gain @ +10• 100 meter (300 feet) line-of-sight operating range• Selectable modulation modes optimize performance for spectral effi-ciency or audio quality:- Standard – optimal coverage, low latency- High density – dramatic increase in max system channel count• Switchable Power Levels in single carrier mode = 2/10/50 mW (region dependent)• Power Level 2x20 mW in frequency diversity mode (region dependent)• Built-in tone generator and RF markers to facilitate range-testing Design• Interchangeable Shure microphone cartridges• Backlit LCD with easy to navigate menu and controls• Rugged metal construction• Menu and power lockoutPower• Shure SB920 rechargeable batteries for up to 9 hours of runtime, preci-sion metering, and zero memory effect• AA-compatible battery sled available• External charging contacts for docked charging
5ADX2FD Transmitter Overview① Microphone CartridgeSee Optional Accessories for a list of compatible cartridges.② Display View menu screens and settings. Press any control button to activate the backlight.③ Infrared (IR) Port Align with the receiver IR port during an IR Sync for automated transmitter programming.④ Control Buttons Use to navigate through parameter menus and change values.⑤ Battery CompartmentRequires Shure rechargeable battery.⑥ On/Off SwitchPowers the unit on or off.⑦ HandleUnscrew to access controls and batteries. ⑧ Battery Charging ContactsCharging contacts for use with docking battery chargers.12345867Transmitter ControlsUse to navigate through parameter menus and change values.XExit: Acts as a 'back' button to return to previous menus or parameters without confirming a value changeOEnter: Selects menu screens and confirms parameter changes∨∧ Use to scroll through menu screens and to change param-eter valuesTip: Use the following control shortcuts for quick set up:• Hold the ∧ button while powering-on to lock the transmitter controls• Hold the X button while powering-on to set the transmitter RF output to muteHome Screen DisplayThe home screen shows transmitter information and status.Tip: There are four options to choose the information shown on the home screen. Use the arrow buttons to select one of the following choices:• Name• F1 and F2 Frequency Settings• F1 and F2 Group (G) and Channel (C)• Device IDShure470.200MHz7:45The following icons appear to indicate transmitter settings:Battery runtime in hours and minutes or bar displayKey: Displayed when encryption is enabledDisplayed when controls are locked. Icon will flash if access is attempted to a locked control (power or menu).ShowLink signal strength displays 0 to 5 barsSTD: Standard Transmission ModeHD: High Density Transmission ModeBox: When the box has an "x", Mute Mode is on and engaged. If the box is empty, Mute Mode is on, but not engaged.Locking the InterfaceLock transmitter interface controls to prevent accidental or unauthorized changes to parameters. The lock icon is shown on the home screen when the interface lock in enabled. 1. From the Utilities menu, navigate to Lock and select one of the following lock options: - None: The controls are unlocked - Power: The power switch is locked - Menu: The menu parameters are locked - All: The power switch and menu parameters are locked2. Press O to save.Tip: To quickly unlock a transmitter: Press O twice, select Unlocked, and press O.
6Shure Rechargeable BatteriesShure lithium-ion batteries offer a rechargeable option for powering the transmitters. Batteries quickly charge to 50% capacity in one hour and reach full charge within three hours.Single chargers and multiple bay chargers are available to recharge the Shure batteries.Caution: Only charge Shure rechargeable batteries with a Shure battery charger.Checking Battery InfoWhen using a Shure rechargeable battery, the receiver and transmitter home screens display the number of hours and minutes remaining.Detailed information for the battery is displayed Battery menu of the transmitter: Utilities > Battery• Battery: The chemistry type of for the installed battery (Shure, Alkaline, Lithium, NiMH)• Bars: Indicates the number of bars displayed• Time: Battery runtime• Charge: Percentage of charge capacity• Health: Percentage of current battery health• Cycle Count: Total of the number of charging cycles for the installed batteryCharge85%Battery Installation① Accessing the Battery CompartmentUnscrew and remove the handle as shown.② Inserting the BatteryInsert the battery, contracts first into the battery compartment. Press down on the tab to fully seat the battery, and then reinstall the handle.Tip: To remove the battery, pull up on the tab on the bottom of the battery.Important Tips for Care and Storage of Shure Rechargeable BatteriesProper care and storage of Shure batteries results in reliable performance and ensures a long lifetime.• Always store batteries and transmitters at room temperature • Ideally, batteries should be charged to approximately 40% of capacity for long-term storage• Periodically clean the battery contacts with alcohol to maintain ideal contact• During storage, check batteries every 6 months and recharge to 40% of capacity as neededFor additional rechargeable battery information, visit www.shure.com.
7Menu ParametersMenu MapAudioOsetMuteTone GenLevelUtilitiesDevice IDLockMarkerAboutBatteryTalk SwReset AllRadioF2 CtrlF2 FreqF1 FreqPowerOutputThe Main menu organizes the avail-able transmitter parameters into three categories:• Radio• Audio• UtilitiesMainRadioTips for Editing Menu Parameters• To access the menu options from the home screen, press O . Use the arrow buttons to access addi-tional menus and parameters.• A menu parameter will blink when editing is enabled• To increase, decrease or change a parameter, use the arrow buttons• To save a menu change, press O• To exit a menu without saving a change, press XRadio MenuF1 FreqPress the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to adjust the values. To edit the frequency, press the O button once to edit the first 3 digits, or twice to edit the second 3 digits.F2 FreqPress the enter button to enable editing of a group (G:) channel (C:) or frequency (MHz). Use the arrow buttons to adjust the values. To edit the frequency, press the O button once to edit the first 3 digits, or twice to edit the second 3 digits.F2 CtrlTurns F2 (F2 Freq) On or Off. PowerHigher power settings can extend the range of the transmitter.Output - On: RF signal is active - Mute: RF signal is inactiveAudio MenuOffsetAdjust Offset level to balance mic levels when using two transmitters for frequency diversity or when assigning multiple transmitters to receiver slots. Adjustment range: -12 dB to +21 dB.MuteWhen enabled, the power switch is configured as a mute switch for the audio: - Power switch on: audio signal on - Power switch off: audio signal mutedTone GenTransmitter will generate a continuous test tone: - Freq: The tone can be set to 400 Hz or 1000 Hz. - Level: Allows for adjustment of the output level of the test tone.Utilities MenuDevice IDAssign a device ID of up to 9 letters or numbers.Locks - None: The controls are unlocked - Power: The power switch is locked - Menu: The menu parameters are locked - All: The power switch and menu parameters are lockedLocks the transmitter controls and power switch.Link InfoDisplays the following information about the link between a transmitter and receiver: - Not Linked: The transmitter is not linked to a receiver - Linked: The transmitter is linked to a receiver. Select Unlink? to free the transmitter from the receiver link. - Unlinked: The transmitter is not linked to a receiverSL TestShowLink test tool to measure the boundaries of ShowLink coverage.Talk SwIndicates the status of the talk switch.MarkerWhen enabled, press the enter button to drop a marker in Wireless Workbench.BatteryDisplays battery information: - Battery: The chemistry type of for the installed battery (Shure Rechargeable, Alkaline, Lithium, NiMH) - Bars: Indicates the number of bars displayed - Time: Battery runtime - Charge: Percentage of charge capacity - Health: Percentage of current battery health - Cycle Count: Record of the number of charging cycles for the installed batteryAboutDisplays the following transmitter information: - Model Displays the model number - Band Displays the tuning band of the transmitter - FW Version Installed firmware - HW Version Hardware version - Serial Num Serial numberReset AllRestores all transmitter parameters to factory settings.
8IR SyncUse IR Sync to form an audio channel between the transmitter and receiver.Note: The receiver band must match the band of the transmitter.1. Select a receiver channel.2. Tune the channel to an available frequency using group scan or manually turn to an open frequency.3. Power on the transmitter.4. Press the SYNC button on the receiver.5. Align the IR windows between the transmitter and the receiver so that the IR LED illuminates red. When complete, Sync Success! appears. The transmitter and receiver are now tuned to the same frequency.<15 cm (6 in.) AD4QAxient Digital Wireless ReceiverPOWERPUSHCONTROLNAVIGATEIR RFA BOLAUDIOSYNC4RX 4RFA BOLAUDIOSYNC3RX 3RFA BOLAUDIOSYNC2RX 2RFA BOLAUDIOSYNC1RX 1ULXD4Digital Wireless ReceiversyncSync Success!Note: Any change to the encryption status on the receiver (enabling/disabling encryption) requires a sync to send the settings to the transmitter. New encryption keys for the transmitter and receiver channel are generated on every IR sync, so to request a new key for a transmitter, perform an IR sync with the desired receiver channel.Setting the Frequency ManuallyThe transmitter can be manually tuned to a specific frequency, group, or channel.1. Navigate to the Radio menu and select F1 Freq or F2 Freq.2. Scroll to select G: and C: to edit the group and chan-nel, or select the frequency parameter (MHz). When ed-iting the frequency, press O one to enable editing of the first three digits, or twice to edit the last three digits.3. Use the ∧∨ buttons to adjust the group, channel, or frequency.4. Press O to save, and then press X when finished.F1 FreqG: 1 C:1470.450 MHzRF MuteRF Mute prevents transmission of the audio by suppressing the RF signal, while allowing the transmitter to remain powered-on. The home screen displays RF MUTED in this mode.RF OutputMute1. From the Radio menu, navigate to Output.2. Choose one of the following options: - On: RF signal is active - Mute: RF signal is disabled3. Press O to save.Turning the transmitter off and on, or replacing the battery will restore Output to On.Power-on RF MutePower-on RF Mute places the transmitter in RF Mute mode immediately when turned on.• Starting with the transmitter off, press and hold the X button, and then switch on the power• Continue to hold the X button until the RF Muted message appears on the home screenTip: To turn the RF Output on, navigate to Radio > Output and select On.Operating in Frequency Diversity ModeOperating the AXDFD2 in frequency diversity mode with an Axient Digital receiver enables simultaneous transmission of audio on 2 inde-pendent frequencies.1. Select a channel and navigate to the Frequency Diversity setting: Advanced > Frequency Diversity .2. Use the control wheel to select the Combining option.3. Press ENTER to confirm and save.4. Perform an IR sync to link the transmitter to the receiver.In Frequency Diversity, the transmitter will operate on two adjacent re-ceiver channels (1 and 2 or 3 and 4).Turning Off Frequency 2 (Freq 2)If a problem develops with one of the frequencies being used by the transmitter, you can lock on to a single frequency by turning off frequen-cy 2. Turning off one frequency allows the transmitter to continue pass-ing audio while a clear frequency can be found for the second channel.1. From the Radio menu navigate to F2 Ctrl.2. Use the controls to set F2 to On or Off. When set to On, the transmitter will pass audio using Freq 2.
9Input OverloadThe OVERLOAD message is displayed when the audio input experiences a high-level signal. The power LED will turn red as an additional indicator of an overload. Reduce the input signal or enable the input pad to remove the overload.Tip: To enable the input pad, navigate to Audio > Pad and select -12 dB.ShureOVERLOAD7:45Tone GeneratorThe transmitter contains an internal tone generator that produces a contin-uous audio signal. The tone is helpful when conducting a sound check or for troubleshooting the audio signal chain. The level of the tone is adjust-able from -60 dB to 0 dB and the frequency can be set to 400 Hz or 1000 Hz.1. From the Audio menu select Tone Gen.2. Set the frequency to 400 Hz or 1000 Hz.3. Select Level and use the arrow buttons ad-just the value between -60 dB and 0 dB.Tip: Always start with the level set to -60 dB to avoid overloading speakers or headphones.Turn off the tone by selecting Off from the menu or by cycling the trans-mitter power.Tone GenTone: 400HzLevel: -60dbMatching Audio Levels with Mic OffsetWhen linking two or more transmitters to a receiver, there may be a differ-ence in volume levels between microphones or instruments. If this occurs, use the Offset function to match the audio levels and eliminate audible volume differences between transmitters. If using a single transmitter, set Offset to 0 dB.1. Turn on the first transmitter and perform a sound check to test the audio level. Turn off the transmitter when finished.2. Turn on the second transmitter and perform a sound check to test the audio level. Repeat for any additional transmitters.3. If there is an audible difference in the sound level be-tween the transmitters, navigate to the Offset menu (Audio > Offset) in the transmitter to increase or decrease the Offset in realtime to match the audio levels.Mic Offset+3 dBShowLink TestThe ShowLink Test is a tool to find the boundaries of the ShowLink cov-erage area. When the ShowLink test is activated, a five-bar display indi-cating level of the signal quality is shown on the screen. As the transmit-ter moves away from the access point, the number of bars will decrease. ShowLink control is maintained as long as 1 bar is displayed. If the transmitter is beyond the coverage range, ShowLink control will not be possible; however, the audio signal will not be affected or inter-rupted as long as the transmitter is within range of the RF signal. To improve coverage, adjust the location of your access points or place ad-ditional access points to extend coverage.To activate the ShowLink Test: 1. From the Utilities menu, navigate to SL Test.2. Press the O button to start the test and walk the transmitter around the coverage area. Monitor the number of bars displayed and the state of the ShowLink icon. Coverage boundaries are indicated by 0 bars displayed or the ShowLink icon is empty.3. Press the X button to exit the ShowLink test.Tip: During a ShowLink test, press O (enter) to drop a marker in Wireless Workbench.Updating FirmwareFirmware is embedded software in each component that controls functionality. Periodically, new versions of firmware are developed to incorporate additional features and enhancements. To take advantage of design improvements, new versions of the firmware can be uploaded and installed using the Shure Update Utility. The Shure Update Utility is available for download from http://www.shure.com/.Firmware VersioningWhen performing an update, download firmware to the receiver first, and then update transmitters to the same firmware version to ensure consis-tent operation.The firmware numbering for Shure devices uses the following format: MAJOR.MINOR.PATCH (e.g., 1.2.14). At a minimum, all devices on the network (including transmitters), must have the same MAJOR and MINOR firmware version numbers (e.g., 1.2.x).Updating the Transmitter1. Download the firmware to the receiver.2. Access the following menu from the receiver: Device Conguration > Tx Firmware Update.3. align the IR ports between the transmitter and the re-ceiver. IR ports must be aligned for the entire down-load, which can take 50 seconds or longer.Tip: The red alignment LED will turn on when the alignment is correct. 4. Press ENTER on the receiver to begin the download to the transmitter. The receiver will display the progress of the update as a percentage.
10SpecificationsMic Offset Range-12 to 21 dB (In 1 dB steps)Battery TypeShure SB920 Rechargeable Li-IonBattery Runtime@ 10 mWShure SB920up to 9 hoursDimensions256 mm x 51 mm (10.1 in. x 2.0 in.) L x Dia.Weight340 g (12.0 oz.), without batteriesHousingCast AluminumAudio InputConfigurationUnbalancedMaximum Input Level1 kHz at 1% THD145 dB SPL (SM58), typicalNote: Dependent on microphone typeRF OutputAntenna TypeIntegrated Single Band HelicalOccupied Bandwidth<200 kHzModulation TypeShure Axient Digital ProprietaryPower2 mW, 10 mW, 50 mW in single carrier mode. Powel level 2x20 mW in frequency diversity mode.See Frequency Range and Output Power table, varies by regionModeFrequency DiversityDual CarrierSingle CarrierSingle CarrierShowLinkNetwork TypeIEEE 802.15.4Frequency Range2.40 to 2.4835 GHz (16 Channels)RF Output Power10 dBm (ERP)Frequency Bands and Transmitter RF PowerBand Frequency Range (MHz)RF Power (mW)***G53 470 to 510 2/10/40G54 479 to 565 2/10/20G55† 470 to 636* 2/10/40G56 470 to 636 2/10/40G57 470 to 616* 2/10/50G62 510 to 530 2/10/40H54 520 to 636 2/10/40K53 606 to 698* 2/10/40K54 606 to 663** 2/10/40K55 606 to 694 2/10/40 K56 606 to 714 2/10/40 K57 606 to 790 2/10/40 K58 622 to 698 2/10/40 L54 630 to 787 2/10/40 R52 794 to 806 2/10/40 JB 806 to 810 2/10 X51 925 to 937.5 2/10 X55 941 to 960 2/10/40 Note: *with a gap between 608 to 614 MHz.Note: **with a gap between 608 to 614 MHz and a gap between 616 to 653 MHz.Note: ***power delivered to the antenna port.Note: †operation mode varies according to region. In Brazil, High Density mode is used.
11K55 606-694 MHzCountry CodeCode de PaysCodice di paeseCódigo de paísLänder-KürzelFrequency RangeGamme de frequencesGamme di frequenzaGama de frequenciasFrequenzbereichA, B, BG, CH, CY, CZ, D, DK, EST, F *FIN, GB, GR, H, HR, I, IRL, IS, L, LT *M, N, NL, P, PL, RO, S, SK, SLO, TR *all other countries ** This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.G56 470-636 MHzCountry CodeCode de PaysCodice di paeseCódigo de paísLänder-KürzelFrequency RangeGamme de frequencesGamme di frequenzaGama de frequenciasFrequenzbereichA, B, BG, CH, CY, CZ, D, DK, EST, F *FIN, GB, GR, H, HR, I, IRL, IS, L, LT *M, N, NL, P, PL, RO, S, SK, SLO, TR *all other countries ** This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.K57 606-790 MHzCountry CodeCode de PaysCodice di paeseCódigo de paísLänder-KürzelFrequency RangeGamme de frequencesGamme di frequenzaGama de frequenciasFrequenzbereichA, B, BG, CH, CY, CZ, D, DK, EST, F *FIN, GB, GR, H, HR, I, IRL, IS, L, LT *M, N, NL, P, PL, RO, S, SK, SLO, TR *all other countries ** This equipment may be capable of operating on some frequencies not authorized in your region. See Licensing Information.
12CertificationsCertified under FCC Part 74 and Part 15. Certified in Canada to RSS-210. FCC ID: DD4ADX2FDG57This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélec-trique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. Meets essential requirements of the following European Directives: • WEEE Directive 2002/96/EC, as amended by 2008/34/EC • RoHS Directive 2011/65/EU Note: Please follow your regional recycling scheme for batteries and electronic wasteThis product meets the Essential Requirements of all relevant European directives and is eligible for CE marking. Hereby, Shure Incorporated declares that the radio equipment is in compliance with Directive 2014/53/EU. The full text of the EU declaration of confor-mity is available at the following internet address: http://www.shure.com/europe/complianceAuthorized European representative:Shure Europe GmbHHeadquarters Europe, Middle East & AfricaDepartment: EMEA ApprovalJakob-Dieffenbacher-Str. 1275031 Eppingen, GermanyPhone: +49-7262-92 49 0Fax: +49-7262-92 49 11 4Email: EMEAsupport@shure.deLICENSING INFORMATIONLicensing: A ministerial license to operate this equipment may be required in certain areas. Consult your national authority for possible requirements. Changes or modifications not expressly approved by Shure Incorporated could void your authority to operate the equipment. Licensing of Shure wireless microphone equipment is the user’s responsibility, and licensability depends on the user’s classification and application, and on the selected frequency. Shure strongly urges the user to contact the appropriate telecommunications authority concerning proper licensing, and before choosing and ordering frequencies. Information to the userThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna.• Increase the separation between the equipment and the receiver.• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.Australia Warning for WirelessThis device operates under an ACMA class licence and must comply with all the conditions of that licence including operating frequencies. Before 31 December 2014, this device will comply if it is operated in the 520-820 MHz frequency band. WARNING: After 31 December 2014, in order to comply, this device must not be operated in the 694-820 MHz band.This device complies with Industry Canada licence-exempt RSS standard(s). Operation of this device is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
PT. GOSHEN SWARA INDONESIAKompleks Harco Mangga Dua Blok L No. 35 Jakarta PusatI.16.GSI31.00501.0211Europe, Middle East, Africa:

Navigation menu