Shinsei BP000002 Mobile Printer User Manual DP 2E Instruction Manual 3rd edition April 20 2010 CS 4 indd
Shinsei Industries Co., Ltd. Mobile Printer DP 2E Instruction Manual 3rd edition April 20 2010 CS 4 indd
Shinsei >
DP-2E Instruction Manual 4th edition. April 20. 2010.CS.4.
![* Read this manual thoroughly, and do not perform installation, operation, maintenance, or inspection unless you fully understand all of the contents. * Keep this manual in a safe place where you can refer to it easily while installing, operating, and carrying out maintenance or inspections.Mobile PrinterDP-2EMobile PrinterEInstruction ManualIMPORTANT](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-1.png)
![2■Preface...Thank you for selecting our model DP-2E.This product does not contain toxic substances specied bythe RoHS and WEEE Directives.This machine is a mobile printer developed based on a state-of-the-art electronics technology and accumulated experiences.For proper and safe use of this machine, read this instructionmanual thoroughly to become aware of the machine and therelated precautions before working for the installation and operation.After the installation, keep this manual at the place whereyou can refer to whenever it is necessary.SHINSEI INDUSTRIES Co., Ltd., 2010All rights are reserved. No part of this publication may be reproduced,stored in a retrieval system, or transmitted, in any form, or by anymeans, mechanical, electronic, photocopying, recording, or otherwise,without prior written permission of SHINSEI.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-2.png)
![3FCC WARNINGChanges or modications not expressly approved by the partyresponsible for compliance could void the user's authority to operate the equipment.NOTICEThis equipment has been tested and found to comply withthe limits for a Class A digital device, pursuant to part 15 ofthe FCC Rules. These limits are designed to provide reasonable protection against harmful interference when theequipment is operated in a commercial environment.This equipment generates, uses and can radiate radiofrequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radiocommunications. Operation of this equipment in a residentialarea is likely to cause harmful interference in which case theuser will be required to correct the interference at his own expense.This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.This equipment complies with FCC radiation exposure limitesset forth for controlled equipment and meets the FCC radiofrequency (RF) Exposure Guidelines in Supplement C to OET65.The product is mobile device, the separation distance between the user and the device's radiating element is greater than 20cm.The maximum E.I.R.P of the device is 3.523mW, which isless than RF Expo. This device complies with Part 15 of the FCC Rules. Operation issubject to the following two conditions: (1) this device may not causeharmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-3.png)
![4 IC This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operaton of this device. This equipment complies with IC radiation exposure limits set forth for uncontrolled equipment and meets RSS-102 of the IC radio frequency (RF) Exposure rules. The product is mobile device, the separation distance between the user and the device's radiating element is greater than 20cm. The maximum E.I.R.P of the device is 3.523mW, which is less than RF Expo. Europe - EU Declaration of Conformity We, Shinsei Industries Co., Ltd. hereby declare that this device, model DP-2E is in compliance with the essential requirements and other relevant provisions of the R&TTE Directive 1999/5/EC. ■ BluetoothTM Communications This device with built-in wireless telecommunication equipment conforms to the standards, required in the region where the device is used. This device assumes an interference distance of about ten meters or less. Using this device near microwave ovens, wireless LAN equipment, etc. may signicantly reduce the communication distance or make communication impossible. Do not disassemble or modify this device. This device is equipped with a Bluetooth module that obtained product certication. BluetoothTM is a trademark of Bluetooth SIG, Inc., U.S.A., and is used herein under license.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-4.png)
![51. Precaution Symbols ............................................................................ 72. For your longer use ............................................................................. 113. Conrmation of This Machine ............................................................. 13 3-1. Printer Unit .............................................................................. 13 3-2. Accessories ............................................................................. 144. Optional Accessories ..................... ................................................... 155. Names and Functions of Each Part .................................................... 166. When using this machine with the battery pack ................................. 20 6-1. Installing the battery pack .......................................................... 20 6-2. Removing the battery pack ........................................................ 227. Charging the battery pack ................................................................... 23 7-1. Battery charge is needed in one of the following cases ............. 23 7-2. Battery charging procedure ....................................................... 24 7-3. Before using the battery pack .................................................... 268. When charging the battery pack with the charger adapter (sold separately) ................................................. 28 8-1. Installing the charger adapter ...................................................... 28 8-2. Removing the charger adapter .................................................... 299. Setting the media roll ........................................................................... 30 9-1. In the case of printing labels in the Tear-Off mode ...................... 30 9-2. In the case of printing labels in the Peel-Off mode ...................... 33■ Table of Contents](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-5.png)
![610. Power ON-OFF ................................................................................... 37 10-1. Turn on the power ..................................................................... 37 10-2. Turn off the power ..................................................................... 3711. Contrast adjustment of the liquid crystal display ................................. 3812. Adjustment of the backlight lighting time ............................................. 4013. Test Printing ........................................................................................ 42 13-1. Test printing method 1 .............................................................. 42 13-2. Test printing method 2 .............................................................. 4414. Printing the Conguration List ............................................................ 4515. Printer Info........................................................................................... 4716. Conrmation of BluetoothTM communication set value ....................... 4917. Automtic adjustment of the sensor ..................................................... 53 17-1. Automatic adjustment of the label sensor ................................ 53 17-2. Automatic adjustment of the peel sensor ................................. 5618. Connecting the USB (mini-B) ............................................................ 5719. Using the BluetoothTM communications .............................................. 5720. Label issuing mode ........................................................................... 5821. Error messages .................................................................................. 5922. Daily Check and Cleaning Method .................................................... 61 22-1. Printing check (Test pattern printing) ....................................... 61 22-2. Execution of the head check ................................................... 62 22-3. Cleaning of the thermal print head .......................................... 62 22-4. Cleaning of the platen roller and the peel roller ...................... 64 22-5. Cleaning of each sensor .......................................................... 65 23. Specications of this machine .....,,..................................................... 6624. Important Notices ............................................................................... 69■ Table of Contents](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-6.png)
![7This product is manufactured for use according to properprocedures by a qualied operator and only for thepurposes described in this manual.Precaution symbols in this manual are divided into twocategories, depending on the level of danger, orseriousness of potential injury. The denition of each precaution is shown below. Failure to heed these precautions may result in bodily injury or damage to themachine.1. Precaution SymbolsThis machine is manufactured for use according to properprocedures by a qualied person and only for the purposesdescribed in this manual. The following symbols are used in this manual.Always heed the information provided in this manual.Failure to heed precautions can result in personal injury orproperty damage.Heed the following precautions information provided inthis manual for your safety.Indicates information that, if not heeded,could possibly result in loss of lie or seriousinjury.Indicates information that, if not heeded,could result in relatively serious or minorinjury, damage to the machine, or faultyoperation.CAUTIONWARNING](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-7.png)
![8Do not disassemble or modify the printer unit, battery pack, battery charger, charger adapter, etc.Doing so may result in injury or cause the machine to break down.∑ Doing so may cause damage, short-circuit, or ignition, and may result in electric shock, burn, or re.Do not keep the battery pack with metals. ∑ Doing so may cause a re or electric shock due to short-circuit.Do not allow the printer unit, battery pack, battery charger, or charger adapter to come in contact with water or get accumulation of dust.Doing so may result in re or cause the machine to break down.∑ Continued use may cause a re or electric shock.Do not give strong shock such as dropping and throwing the printer unit.∑ Doing so may cause damage, short-circuit, or ignition, and may result in electric shock, burn, or re.Do not charge anything other than the specied battery pack with the battery charger.∑ The battery pack may cause heat, burst, or ignition.WARNING・・・・Do not charge anything other than the speciedbattery pack with the battery charger.・ The battery pack may cause heat, burst, or ignition.・ Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-8.png)
![9Do not touch the thermal print head because it will be exposed when the cover is opened.∑ When replacing labels immediately after using the machine, be careful not to get burned due to overheating of the thermal print head.∑ Do not touch the thermal print head as your hand oil may cause the deterioration.Do not leave the battery pack charged for a long time.After the charge, make sure to pull out the plug of the power supply cord of the battery charger or the charger adapter from the AC outlet.The operation time may become less because the battery pack is naturally discharged and the power decreases. (It is not a breakdown).CAUTION・・ Change or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-9.png)
![10After using this machine or when not using it for a long time, take out the battery pack and pull out the power plug of the charger adapter from the AC outlet for safety.Do not charge anything other than the specied battery pack (lithium-ion battery).∑ Follow the local regulation when disposal.Do not place this machine on an unstable place.∑ Doing so may fall and injury.Remove dusts regularly after pulling out the power plug of the charger adapter from the AC outlet.∑ If dusts are accumulated around the AC outlet, it may cause leak current and re.CAUTION・・・](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-10.png)
![112. For your longer usePrecautions for use1. Do not print the paper with the paper not installed. 2. Issue labels after conrming the print contents are correct, as set values of a built-in program might be changed or destroyed by an excessive power supply noise.3. Avoid use of this machine under the conditions of extreme temperature or humidity.4. Do not leave or keep the machine in the place where an air conditioner is installed near the machine or direct sunlight is received. [Environment] Operating environmental temperature: +5o ~ +35oC Operating environmental humidity: 25 ~ 80%RH (No condensation) Storage environmental temperature: -10o ~ +60oC Storage environmental humidity: 10 ~ 80%RH (No condensation)5. When glue or dust adheres to the label path, wipe it off with a soft cloth wrung after being soaked in neutral detergent.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-11.png)
![126. Use the battery pack after full charge when using it for the rst time.7. In the case of using this machine with the battery pack, turn off the power even when interrupting the use temporarily. This will save the battery pack power.8. Clean the thermal print head regularly and perform test printing. Contact our dealer if a white line appears on the test pattern. Normal pattern Abnormal pattern9. Inspection at the beginning of a working day Perform test printing at the beginning of a working day. Refer to Section 13 "Test Printing".10. Use our specied media to maintain good print quality and performance.Contact our dealer if an abnormal pattern should be printed.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-12.png)
![133. Conrmation of This MachineThis machine is composed of the printer unit and accessories. 3-1. Printer UnitYou can select one of two types, either DP-2E (for a small label roll) that can contain the media roll with small diameter or DP-2E (for a large label roll) that can contain the media roll with large diameter.The following pages are described by using gures of the DP-2E(for a small label). (for a small label roll) (for a large label roll)Mobile PrinterDP-2EDP-2EMobile Printer](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-13.png)
![14 3-2. AccessoriesHead cleanerBrushInstruction manual CD-ROMThey are attached to the printer unit.Instruction manualMobile Printer DP-2E](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-14.png)
![154. Optional AccessoriesFollowing optional accessories need to be purchased separately.*Contact our dealer for other optional accessories.Charger adapter(CV-74)Battery pack(BH-74)Battery charger(CH-74)Protector(DP-74)USB cable(mini-B)Belt hook(DH-74B)Portable holster(DH-74)Rainproof case(DH-74R)Auxiliary case(HH-74)](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-15.png)
![165. Names and Functions of Each PartMobile Printer DP-2E](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-16.png)
![17](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-17.png)
![18No. Name Function① Power switch Turn on and off the power supply.② FEED key Press this key when feeding paper or moving the cursor on the menu screen.③ MENU key Press this key when changing the screen.④ Power LED The green LED lights up when the power supply is turned on.⑤ Status LED The red LED lights up if an error display appears.⑥ Charge LED This LED lights up while charging with the charger adapter (option).⑦ Liquid crystal display The remaining battery level and various statuses are displayed.⑧ Cover Open or close this cover when removing or installing the media roll.⑨ Cover lock release lever Press to release the cover lock when opening the cover.⑩ Label holder This holder guides the media.⑪ Stopper This stopper keeps the label holder opened.⑫ Thermal print head This head performs printing on the media.⑬ Platen roller This roller holds the media with the thermal print head and transports the media.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-18.png)
![19No. Name Function⑭ Peeling frame This frame peels off labels from the backing paper.⑮ Peel frame release lever Open the peel off frame with this lever.⑯ Peel roller This roller guides the backing paper to the issuing slot.⑰ Peel sensor This sensor detects a peeled label presence.⑱ Label sensor This sensor detects a label transportation.⑲ USB connector cover Open this cover to connect a PC with the USB cable. Use in a commercial, industrial or business environment, exclusive of a device which is marketed for use by the general public or is intended to be used in the home.⑳ DC input terminal cover Connect the charger adapter (option). Auto/Manual switch Press to select "auto issue" or "manual issue" in the Peel-Off mode. Battery pack cover This covers the storage unit of the battery pack. Battery pack release lever Use this lever when taking out the battery pack.㉑㉒㉓](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-19.png)
![206. When using this machine with the battery pack 6-1. Installing the battery pack(1) Open the battery pack cover. ・ Slide the battery pack cover to the arrow direction.(2) Insert the fully-charged battery pack into the battery pack storage unit of this machine with its terminals inside until it clicks. Terminal](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-20.png)
![21(3) Close the battery pack cover. ・ Push to slide the battery pack cover until it clicks so that the protruding portions on both sides of the battery pack cover can be inserted into the slit of this machine.(4) Turn on the power. The green Power LED lights up, and the power is turned on.Protruding portion](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-21.png)
![22 6-2. Removing the battery pack(1) Turn off the power supply. ・ Conrm that the Power LED is turned off.(2) Open the battery pack cover. ・ Pull to slide the battery pack cover in the arrow direction to release the lock, and open the cover.(3) Remove the battery pack. ・ Slide the battery pack release lever in the arrow direction until the lock is released.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-22.png)
![237. Charging the battery pack 7-1. Battery charge is needed in one of the following cases(1) When using the battery pack for the rst time, or not using it for a long time.(2) When nothing appears on the liquid crystal display at the time of power-on, or when the display turned off soon though the remaining battery level had been displayed once.(3) When the remaining battery level becomes 1/4 or less. (4) When the display turned off while each item was being input.(5) When operation stopped while printing and the "low battery" message is displayed.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-23.png)
![24 7-2. Battery charging procedure(1) Insert the output side of the power cable into the input side of the battery charger and insert the cable plug into the AC outlet. ・ The Power LED (red) lights up.(2) Insert the battery pack and slide it in the arrow direction to lock the pack until it clicks. ・ The Charge LED (red) lights up when the charge starts. The Charge LED (red) turns off when the battery is fully charged.(3) Remove the battery pack when the charge ends. ・ Charge time: 3 hours ・ Number of charge times: 300 times * Use the charge time and the number only as a guide. They may vary according to status of use.If the Charge LED blinks, stop charging because the battery pack trouble is presumed.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-24.png)
![25 ・ Do not disassemble or modify the battery pack. Doing so may cause a damage, short-circuit, or ignition, and may result in an electric shock, burn, or re. ・ Do not allow the machine to come in contact with water or get accumulation of dusts. Doing so may result in a re or cause the machine to break down. ・ Do not keep the battery pack with metals. Doing so may cause a re or electric shock due to short-circuit. ・Do not leave the battery pack charged for a long time. ・ After the charge, make sure to pull out the plug of the power supply cord of the battery charger or the charger adapter from the AC outlet. ・ The operation time may become less because the battery pack is naturally discharged and the power decreases. (It is not a breakdown). ・ Do not charge the battery pack when the pack is still high in temperature. ・ Charge the battery pack after the temperature drops. ・ Caution should be exercised because the battery pack is still in high in temperature immediately after the charge.WARNINGCAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-25.png)
![26 7-3. Before using the battery pack(1) About the battery pack Note that the deterioration speed (life time) of the battery pack depends greatly on overcharge and over-discharge. ・ Notes not to cause overcharge Do not charge the battery pack many times in a short period of time without discharging electricity. ・Notes not to cause over-discharge Charge the battery pack promptly when the warning appears on the display indicating that the remaining battery level is low. There is a possibility that the battery pack is in the over-discharge state when the pack has been connected with the machine over an extended time period (The pack is discharged even in the power-off state), or when the pack has been left for a long time. ・ Optimizing the change It is the best to charge the battery pack when the remaining battery level becomes 1/4 or less for prolonging the battery life.If the lithium-ion battery is over-discharged, it cannot be normally charged.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-26.png)
![27(2) Others ・ The battery pack might be high in temperture shortly after a large amount of printing has been made with this machine.・ The lithium-ion battery capacity remarkably decreases under the low-temperature environment. Early charging is recommended.・ Replace with a new battery pack when the pack cannot be fully charged or the operating time decreases.Charge the battery pack after the temperature falls.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-27.png)
![288. When charging the battery pack with the charger adapter (sold separately) 8-1. Installing the charger adapter(1) Install the battery pack in this machine.(2) Remove the DC input terminal cover of this machine in the power-off state, and connect the DC output terminal of the charger adapter with the DC input terminal of this machine.(3) Connect the power plug of the charger adapter with the AC outlet.(4) The Charge LED lights up and the battery charge starts. ・ Charge time: 5 hours ・ Number of charge times: 300 times.* Use the charge time and number only as a guide. They may vary according to status of use.(5) The Charge LED turns off when the battery pack is fully charged. ・ Remove the charger adapter by using the method of "8-2" on the next page.Charge LEDMobile Printer DP-2E](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-28.png)
![29 8-2. Removing the charger adapter(1) Remove the power plug of the charger adapter from the AC outlet.(2) Remove the DC output terminal of the charger adapter from the DC input terminal of this machine, and close the DC input terminal cover of this machine.Make sure to turn o the power of this device when removing the DC output terminal of the charger adapter from the DC input terminal of this machine, or removing the plug of the charger adapter from the AC outlet.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-29.png)
![309. Setting the media roll 9-1. In the case of printing labels in the Tear-Off mode (1) Open the cover by pressing the cover lock release lever. (2) Lift up the stopper and adjust the label holder to the media width. After conrming that the holder ts the media width, lower the stopper.Cover lockrelease leverLabel holderStopperMoving the label holder without raising the stopper may cause damage.CAUTIONMobile Printer DP-2E](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-30.png)
![31・ (3) Place the label roll so that the print face directs downward (thermal print head side). See the machine specications about the size of the label that can be placed.∑ Do not touch the thermal print head because it will be exposed when the cover is opened. When replacing labels immediately after using the machine, be careful not to get burned due to overheating of the thermal print head.∑ Do not touch the thermal print head as your hand oil may cause the deterioration. Print faceLabel rollLabel holderCAUTION・・](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-31.png)
![32 (4) Pull out the label roll and gently close both ends of the cover until they click as indicated by an arrow. (5) Press the FEED key. The label is fed to the xed position. A mark error will occur if the label size or the sensor type is different.∑ Closing the cover strongly may cause trouble or damage.∑ Caution should be exercised so as not to get your hand caught.Label rollCoverLabel rollMobile Printer DP-2EWARNING・・](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-32.png)
![33 9-2. In the case of printing labels in the Peel-Off modeWhen issuing labels in the Peel-Off mode, it is necessary toset the main body setting to the Peel-Off mode from a personal computer etc. (not possible to set it with this machinealone).(1) Open the cover by pressing the cover lock release lever.(2) Lift up the stopper and adjust the label holder to the label width. After conrming that the holder ts the label width, lower the stopper.Cover lockrelease leverLabel holderStopperMoving the label holder without raising the stopper may cause damage.CAUTIONMobile Printer DP-2E](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-33.png)
![34(3) Place the label roll so that the print face directs downward (thermal print head side). See the machine specications about the size of the label that can be placed.(5) Slide the peel frame release levers on both sides inward and lift it to open the peel frame. Mobile Printer DP-2EMobile Printer DP-2EBacking paperPeel framePeel framerelease leverCoverPrint faceLabel holderLabel roll(4) Peel off one label at the top of the label roll, pull the backing paper to front, and gently close both ends of the cover until they click as indicated by an arrow.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-34.png)
![35(6) Thread the backing paper from which one label was peeled off between the peel frame and the cover. (7) Close the peel frame gently until it clicks. The peel frame is xed.Closing the peel frame strongly may cause trouble or damage.Backing paperPeel framePeel frameCoverWARNING](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-35.png)
![36(8) Slide the switch to either "Auto issue" or "Manual issue" position. 1. "Auto issue" setting Slide the switch to front to set the automatic label issuing mode. ・In "Auto issue" mode, the label's presence is detected by the peel sensor. Therefore, the next label is automatically peeled off from the backing paper, and fed out of the label outlet every time current label is removed. 2. "Manual issue" setting Slide the switch to rear to set the manual label issuing mode. ・ The next label is peeled off from the backing paper and fed out of the label outlet every time the [FEED] key is pressed.ModechangeswitchModechangeswitch](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-36.png)
![3710. Power ON-OFF 10-1. Turn on the power Hold down the POWER key for about one second and release it when the green Power LED lights up. ・ The following standby screen appears as shown in the gure below after the logo mark is displayed for a few seconds, and the version of the machine continues to be displayed till the rst operation. *Here, the remaining battery level is displayed to indicate the charging state. 10-2. Turn off the power Hold down the POWER key and release it after the Power LED turns off.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-37.png)
![3811. Contrast adjustment of the liquid crystal display(1) Turn on the power. The standby screen appears.(2) Press the MENU key for about one second to display the Menu 1/4 screen. Conrm the cursor is located on the [next] button, and press the FEED key.(3) Conrm that [1. contrast] is selected and press the MENU key. menu 1/4 exit1. contrast2. backlightnext menu 1/4 next exit 2. backlight 1. contrast](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-38.png)
![39(4) Each time you press the FEED key under this condition, [-], [+], or [exit] is selected in this order. Select [+] to increase the contrast, or [-] to decrease the contrast, and press the MENU key to change the numeric value for changing the contrast. (1 ~16)(5) After completing the setting, select [exit] by using the FEED key and press the MENU key.(6) The display returns to the Menu 1/4 screen. Press the MENU key for about one second to return to the standby screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-39.png)
![4012. Adjustment of the backlight lighting time(1) Turn on the power. The standby screen appears.(2) Press the MENU key for about one second to display the Menu 1/4 screen. Conrm the cursor is located on the [next] button, and press the FEED key.(3) Select [2. backlight] by using the FEED key, and press the MENU key. menu 1/4 exit1. contrast2. backlightnext menu 1/4 next exit1. contrast 2. backlight](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-40.png)
![41(4) Each time you press the FEED key under this condition, [-], [+], or [exit] is selected in this order. Select [+] to lengthen the lighting time, or [-] to shorten the time, and press the MENU key to change the numeric value (0 - 90 seconds).(5) After completing the setting, select [exit] by using the FEED key and press the MENU key.(6) The display returns to the Menu 1/4 screen. Press the MENU key for about one second to return to the standby screen.backlightbacklight](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-41.png)
![4213. Test Printing 13-1. Test printing method 1(1) Turn on the power. The standby screen appears.(2) Press the MENU key for about one second to display the Menu 1/4 screen. Conrm the cursor is located on the [next] button, and press the MENU key.(3) The Menu 2/4 screen appears. Select [3. test print] by using the FEED key, and press the MENU key.menu 2/4 next exit4. print setting 3. test printmenu 1/4 exit1. contrast2. backlightnext](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-42.png)
![43(4) Each time you press the FEED key under this condition, [NO], [YES], or [exit] is selected in this order. Select [NO] by using the FEED key for not printing, and press the MENU key. Then, the Menu 2/4 screen appears. Select [YES] by using the FEED key for printing, and press the MENU key. Then, the test pattern is printed. (5) When completing the operation, select [exit] by using the FEED key and press the MENU key.(6) The Menu 2/4 screen appears. Press the MENU key for about one second to return to the standby screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-43.png)
![44 13-2. Test printing method 2(1) Hold down the POWER key while holding down the FEED key to turn on the Power LED, and release both FEED and POWER keys when the test pattern is displayed.(2) Conrm that the normal pattern is printed. ・ Contact our dealer if the abnormal pattern should be printed.Normal patternAbnormal pattern](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-44.png)
![4514. Printing the Conguration List・ The set value list is printed in 200mm long and 48mm wide. The print might overow depending on labels. Receipt paper of 48mm or more in width is recommended.(1) Turn on the power. The standby screen appears. (2) Press the MENU key for about one second to display the Menu 1/4 screen. Conrm the cursor is located on the [next] button, and press the MENU key.(3) The Menu 2/4 screen appears. Select [4. print settings] by using the FEED key, and press the MENU key. menu 1/4 exit1. contrast2. backlightnext menu 2/4 next exit 3. test print 4. print settings](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-45.png)
![46(4) Each time you press the FEED key under this condition, [NO], [YES], or [exit] is selected in this order. Select [NO] by using the FEED key for not printing, and press the MENU key. Then, the Menu 2/4 screen appears. Select [YES] by using the FEED key for printing, and press the MENU key. Then, the test pattern is printed. (5) When completing the operation, select [exit] by using the FEED key and press the MENU key.(6) The Menu 2/4 screen appears. Press the MENU key for about one second to return to the standby screen. menu 2/4 exit 3. test print 4. print settingsnext](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-46.png)
![47menu 3/4 exit 5. Printer Info 6. bluetooth15. Printer Info menu 1/4 exit 1. contrast 2. backlightnext menu 2/4 exit 3. test print 4. print settingsnext(1) Turn on the power. The standby screen appears.(2) Press the MENU key for about one second and the menu 1/4 screen appears.(3) Conrm the cursor is located on the [next] button and press the MENU key, the menu 2/4 screen appears.(4) Conrm the cursor is located on the [next] button and press the MENU key, the menu 3/4 screen appears.next](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-47.png)
![48Printer Info exitSYSX. XXIPL_DP2_X.XXXXX.Xkmnext Printer Info exitEnglishANSI Latin 1next (5) To display the Printer Info, move the cursor to " 5. Printer Info" by using the FEED key. menu 3/4 next exit 5. Printer Info 6. bluetooth(6) Conrm the cursor is located on the " 5. Printer Info" and press the MENU key. The Printer Info screen below appears.(7) Press the MENU key and the following screen appears. To return to the menu screen Press the MENU key for about one second.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-48.png)
![49(1) Turn on the Power. The standby screen appears.(2) Press the MENU key for about one second to display the Menu 1/4 screen. Conrm the cursor is located on the [next] button, and press the MENU key.(3) The Menu 2/4 screen appears. Conrm the cursor is located on the [next] button, and press the MENU key. 16. Conrmation of BluetoothTM communication setting value(4) The Menu 3/4 screen appears. Select [6. bluetooth] by using the FEED key, and press the MENU key.menu 1/4 exit1. contrast2. backlightmenu 2/4 exit3. test print4. print settingsmenu 3/4 next exit5. Printer Infonextnext6. bluetooth](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-49.png)
![50(5) The selection screen for [1. print BDA] and [2. show settings] appears. Conrm the cursor is located on the [1.print BDA] button, and press the MENU key.bluetooth exit2. show settings1. print BDA(6) The [print BDA] screen appears.In case of [NO]bluetooth print BDA YESNO●In case of [NO], conrm the cursor is located on the [NO], and press the MENU key for about one second to return to the standby screen.※If the MENU key is pressed on this screen, the screen returns to the previous selection screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-50.png)
![51●When printing BDA, select [YES] by pressing the FEED key, and the Bluetooth authentication address (BDA) is printed.●After printing BDA, press the MENU key for about one second to return to the standby screen.※If the MENU key is pressed on this screen, the screen returns to the previous selection screen.In case of [YES](7) Select [2.show settings] on this screen by using the FEED key, and press the MENU key.bluetooth exit1. print BDA 2. show settings①The initial set values are displayed.bluetooth exitBDA/Name:000190E130A0SHINSEI PRINTERnext](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-51.png)
![52②Conrm the cursor is located on the [next] button, and press the MENU key to display the next set value.bluetooth exitPIN:0000000000000000Auth:nonenext③Conrm the cursor is located on the [next] button, and press the MENU key to display the last set value.bluetooth exitModuleVersion:0100next●Press the MENU key for about one second on this screen, and the screen returns to the standby screen.※Conrm the cursor is located on the [next] button and press the MENU key to return to the initial set value screen.※Selecting [exit] on this screen by using the FEED key and press the MENU key to return to the Menu 3/4 screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-52.png)
![5317. Automatic adjustment of the sensorPerforms the automatic sensitivity adjustment of the label sensor and the Peel sensor.17-1. Automatic adjustment of the label sensor(1) Conrm the cursor is located on the [next] button on the Menu 3/4 screen and press the MENU key, and the Menu 4/4 screen appears. To perform the automatic adjustment of the label sensor to x the label position, select [7. sensor Adjust] by using the FEED key and press the MENU key.menu 4/4 next exit7. sensor Adjust 8. peel Adjust(2) Selection screen for the label type appears. Select the label type either [1. mark Label] or [2. gap Label] by using the FEED key.In case of mark Label ①Conrm the cursor is located on the [1. mark Label] and press the MENU key.autoSensor exit2. gap Label 1. mark Label](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-53.png)
![54② The mark sensor adustment screen appears. Every time the FEED key is pressed, [NO] ⇒ [YES] ⇒ [exit] appears.mark exitsensor Adjust YESNO ③If the sensor adjustment is not required, conrm the cursor is located on the [NO] and press the MENU key to return to the previous selection screen. ④ If the sensor Adjust is required, select [YES] by using the FEED key and press the MENU key. ● If the sensor is adjusted normally, the following screen appears.autoSensor ENDexit ● Press the MENU key for about one second on this screen to return to the standby screen. ※ Conrm the cursor is located on the [exit] on this screen and press the MENU key to return to the previous selection screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-54.png)
![55In case of gap Label ①Select [2. gap Label] on the label type selection screen by using the FEED key and press the MENU key.autoSensor exit1. mark Label 2. gap Label Hereafter, follow the procedure described in the mark Label ②⇒③⇒④ on the Page 54.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-55.png)
![56(1) Conrm the cursor is located on the [next] on the Menu 3/4 screen and press the MENU key to display the Menu 4/4 screen. To adjust the sensitivity of the Peel sensor that detects label, select [8. peel Adjust] by using the FEED key and press the MENU key.17-2. Automatic adjustment of the Peel sensormenu 4/4 next exit7. sensor Adjust 8. peel Adjust(2) The threshold setting screen for the Peel sensor appears. +Peel exitthreshold 119 - ● To lower the threshold, select [-] and press the MENU key. The threshold is lowered one by one by pressing the MENU key. The Peel sensor sensitivity becomes lower if the threshold is lowered. ● To increase the threshold, select [+] by using the FEED key and press the MENU key. The threshold is increased one by one by pressing the MENU key. The Peel sensor sensitivity becomes higher if the threshold is increased.(3) After setting the threshold, press the MENU key for about one second to return to the standby screen. ※ Select [exit] by using the FEED key on this setting screen and press the MENU key to return to Menu 4/4 screen.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-56.png)
![5718. Connecting the USB (mini-B)(1) Open the connector cover for USB.(2) Connect the USB connection cable (option) with the connector for USB. ・ The USB sign on the USB terminal (mini-B) must face the arrow sign on the printer.(3) This port is only used for data transfer, no supply function.19. Using the BluetoothTM communicationsWhen printing by the use of BluetoothTM communications, the use distance is different according to the use environment or the hand-held portable data terminal.Caution should be exercised because communication distancemight shorten remarkably or communications might not be possibleparticularly around microwave oven, place where interference occurs,or wireless LAN equipment.Mobile Printer DP-2EUSB terminal (mini-B)USB sign](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-57.png)
![5820. Label issuing mode(1) Data is sent from the personal computer or the hand-held portable data terminal.(2) In the case of Tear-off mode The specied number of labels is printed and fed.(3) In the case of Peel-Off mode You can select "Automatic issue" or "Manual issue" using the change switch. Slide the switch to either "Auto issue" or "Manual issue" position. * Refer to 9-2-(8) for more information about "Auto issue" and "Manual issue".Mode changeswitch](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-58.png)
![5921. Error messagesIf an error occurs with this machine, the red Status LED lights up,and the state is displayed. Take measures according to the dealingprocess.No. LCD LED Status Measures 1 cancel / resume printing Off This indicates a suspended label issue state. Makes a selection using the FEED and MENU keys. 2 cool down (count down) Off This indicates a resting state due to over-heated motor at the normal issue. The label will be automati- cally issued after the motor is cooled. 3 head over heated Off This indicates a resting state for cooling due to overheated head. Intermittent operation: about 5 min. ON/ 20 min. OFF. The label will be automati- cally issued after the motor is cooled. 4 paper endOn (red) This indicates a label end detecting state. Replace with new labels.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-59.png)
![60No. LCD StatusLED Status Measures5 Cover open On (red) This indicates a cover opening state. Close the cover.6 low batteryOn (red)for about10seconds This indicates a battery low detecting state. The power will be turned off in 10 seconds. Charge the battery.7 head error Off This indicates a head failure state. Contact our dealer8 label error On (red) This indicates a mark un- detectable state. Replace with a correct label.9 BT Off This indicates a built-in Bluetooth failure state. Contact our dealerNo. LCD Charge LED Status Measures1(Nothing is displayed) BlinkingThis indicates a battery degradationstate. Replace with a new battery.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-60.png)
![6122. Daily Check and Cleaning Method 22-1. Printing check (Test pattern printing)First of all, print the test pattern before issuing labels. Check that the thermal print head works normally and the pattern is printed correctly.(1) Turn on the power of this machine.(2) Print the test pattern according to the procedure described in Section 13 "Test Printing".(3) Check that there is no white line on the printed test pattern.Normal patternAbnormal pattern](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-61.png)
![62 22-2. Execution of the head checkThe head is automatically checked when the machine power is turned on. If the messge "head error" is displayed, contact our dealer.・Use this head check as a guide. Test printing can be normal if the message "head error" is displayed, or the message will not appear if test printing is abnormal. In this case, prioritize test printing. 22-3. Cleaning of the thermal print headNormal printing cannot be made when glue or dust adheresto the print head, clean the thermal print head.(1) Open the cover by lowering the release lever and take out the media roll.(2) Check that glue or dust does not adhere to the print head.(3) Carefully wipe off extraneous objects if any with the attached head cleaner.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-62.png)
![63(4) Use the head cleaner after cutting the dirty part when the cleaner gets dirty.∑ Do not use anything other than the specied head cleaner.∑ Do not remove extraneous objects with a sti-pointed thing such as a driver or pencil. Doing so may cause damage of the thermal print head.∑ Do not clean the machine when the thermal print head is still high in temperature. Doing so may cause a burn.Head cleanerThermal print headCAUTION・・・](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-63.png)
![64 22-4. Cleaning of the platen roller and the peel roller(1) Open the peel frame by sliding the peel frame release lever.(2) Open the cover by pressing the release lever. Then, take out the media roll.(3) Clean the platen and peel rollers with a soft cloth wrung after being soaked in neutral detergent.Mobile Printer DP-2EPlaten rollerPeel rollerPeel frame release leverDo not use organic solvents such as benzene and thinner may dissolve the machine or platen roller. Doing so may cause a trouble.CAUTION](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-64.png)
![65 22-5. Cleaning of each sensor(1) Open the cover by lowering the cover release lever, and take out the media roll.(2) Clean the label sensor and peel sensor with the attached brush. ・There is a possibility that dusts adhere to the label sensor if the red Status LED lights up even though labels are correctly set.Peel sensorLabel sensor](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-65.png)
![6623. Specications of this machineSpecications/Model name DP-2E Printer unit Print method Direct thermal Resolution 8 dots/mm (203 dpi) Print speed Max. 100mm/second (standard printing) Effective print range Width: 48mm Length: 100mm External dimensions ・DP-2E (for a small label roll) 123mm(L) x 85mm(W)x 64mm(H) (excluding protruding portions) ・DP-2E (for a large label roll) 146mm(L) x 85mm(W) x 76mm(H) (excluding protruding portions) Weight ・DP-2E (for a small label roll) 398g (including battery pack) ・DP-2E (for a large label roll) 411g (including battery pack) Power supply Battery Special lithium-ion battery (7.4V, 2500mAh)](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-66.png)
![67Display unitLCD 128 x 64 dots Dot matrix liquid crystal display (with backlight) LED 3 LEDs (Power, Status, Charge)Operationpanel Buttons 3 buttons (Power, MENU, FEED)Interfaces BluetoothTM BluetoothTM Conforming to Ver. 1.2 (Class 2)USB cable(mini-B) Use of exclusive use cableCommunicationmethod SPLM (command method using special protocols)Label printingmode Tear-off, Peel-offLabel(Outside woundlabel/paperonly)Labelbackingpaper width 24 - 58mm Media rolloutsidediameter 58mm or less (for a small label roll) ・DP-2E (for a large label roll) 70mm or less (desk-top standard label)Label marktype I mark/Black mark, Gap, No mark](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-67.png)
![68 Barcode type EAN 8, EAN 13, JAN 8, JAN 13, UPC-A, UPC-E, NW-7, Interleaved 2 of 5 (ITF), CODE 39, CODE 128, EAN 128, RSS Two-dimensional code QR Code, PDF 417 Font Bit map fonts: SSF1: 16 x 24 dots SSF2: 24 x 32 dots Outline fonts (scalable): A Gothic, F European, C European, Gothic, MINCHO, OCR-B Pop font Bit map Kanji fonts (JIS Level 1 & 2): Gothic: 16 x 16, 22 x 22, 24 x 24 dots MINCHO: 22 x 22, 24 x 24 dots Outline Kanji fonts (JIS Level 1 & 2): Gothic (Scalable within 127 dots)Functions Self- diagnosis Error message is displayed on the LCD. Power saving Sleep mode Auto power off Remaining battery level indication Optional accessories Charger adapter (CV-74) Battery charger (CH-74) Battery pack (BH-74) Protector (DP-74) Belt hook (DH-74B) USB cable (mini-B) Portable holster (DH-74) Auxiliary case (HH-74) Rainproof case (DH-74R)](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-68.png)
![6924. Important Notices1. No part of this manual may be reproduced in any form, or by any means, mechanical, electronic, photocopying, recording, or otherwise, without prior written permission.2. The information in this manual is subject to change without notice.3. The information in this manual has been carefully checked and is believed to be accurate; however, no responsibility is assumed for clerical, typographical or proofreading errors, or omissions.4. Please note neither is any liability assumed for damages resulting from the use of the information contained in this publication.](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-69.png)
![70Shinsei Industries Co., Ltd.Head ofce〒114-0004 4-12-15 Horifune, Kita-ku, TokyoTEL: 81-3-3913-0395 FAX: 81-3-3913-9607http://www.shinseiind.co.jpMM0501-2 (04152010)1st edition 2010.04](https://usermanual.wiki/Shinsei/BP000002/User-Guide-1269665-Page-70.png)