Shen Zhen WFLY Technology Development WFT09 Radio Control Transmitter User Manual manual

Shen Zhen WFLY Technology Development Co., Ltd. Radio Control Transmitter manual

Contents

Users Manual II

15. TIMER16. More setting(1). GYRO sens settingThis function is to control two electronic clocks used to keeptrack of time remaining in a competition time allowed, flying timeon a tank of fuel, amount of time on a battery, etc.A good gyro will totally eliminate the need for revo.mixing.The gyro wil sense and correct the unwanted motion for you,so you don’t have to spend time to get a complex curve operatingproperly. It simplifies adjusting/selecting the gyro sensitivity,and can provide more than 2 gyro gain settings. (The higher thegain, the more correction the gyro provides and the “softer” or less responsive the helicopter feels) This function makes thebest possible use of the infight adjustable gain of most gyros.18Setting MethodUse up or down button to select TIMER, OK button is to enter editing.Steps:1. Use direction buttons to select editing part.2. Use +/- button for proper adjustment,3. Press EXIT after setting.WFT09 INSTRUCTION
(2). Throttle hovering setting(3). Pitch hovering settingThis function is to set the throttle curve trim at the hovering point.Hovering throttle and hovering pitch are fine-tuning adjustments for the throttle and collectivepitch curves individually, affecting performance only around the center point and only in the normalcondition. They allow in-flight tweaking of the curves for ideal setup.Setting MethodUse up or down button to select Throttle hovering setting/ Pitch hover-ing setting, OK button is to enter editing.Steps:1. Use direction buttons to select editing part.2. Use +/- button for proper adjustment.3. Press EXIT after setting.19WFT09 INSTRUCTIONSetting MethodUse up or down button to select GYRO sens setting, OK button is to enter editing.Steps:1. Use direction buttons to select editing part.2. Use +/- button for proper adjustment,3. Press EXIT after setting
(5). Trim offset settingThis function is to adjust the servo trim at hovering state.Optional separate trims in addition to those for the normal condition.This function is used to automatically change the trim of a helicopter, for example, when transitioned from hover to flying at high speed. Aclockwise-rotation rotor helicopter tends to drift to the right at highspeed, so an aileron offset may be applied to offset the helicopter tothe left. The necessary elevator offset varies with model geometry, soit must be determined by noting collective pitch changes at high speed.The rudder offset is affected by both revo. Mixing and trim lever movementwhile in the offset function.(4). HI/LO PIT settingThis function is to set the high and low pitch position at di-fferent flying modes.20Set up separate trims for each of the three idle-up conditions.Adjust the idle-up 2 rudder trim to correct for torque at high speeds.Steps: 1. Open the OFFSET function.2.Change switch setting to COND.3. Select IDL24. Adjust trim settings as needed.(Ex: rudder to +8%)5. Close menus and confirm difference in trims between nornal and idle-up 2.WFT09 INSTRUCTION
(6). DELAY(7). Governor mixingThis function is to delay the aerobatics or throttle cut when the helicopter is in the air so that to avoid the big trim change.The Delay function provides a smooth transition between the trimpositions whenever OFFSET, REVO. MIXING, or THROTTLE HOLDfunctions are turned on and off.This function is to set the governor.The Governor mixing function is used to adjust the GV-1(Governor)speed settings(rS1,rS2,rS3) from the transmitter.Set up a delay on all 3 channels to ease the transition from one flight condition to another so there are“hard jumps”.Steps:1. Open the DELAY function.2. Adjust AIL response as needed. (Ex: aileron to +8%)3. Repeat for other channels.4. Close menus and confirm slowed transitions.Set up a Gv1 governor to use both channels into the reeiver and switch between the governor settings auto-matically when changing conditions.Consider setting the battery FailSafe settings and other helpful functions on the GV-1 itself.Steps:1. Open and activate the GOVERNOR function.2. Optional: change cut-off channel to channel 8 and assign switch and direction for on/off(channel 8).3. Optional: change switch assignment to select governor settings. Ex: select switch that selects the conditions.4. Adjust governor speed settings per switch position or condition as needed.(Ex: defaults are fine.) Allows headspeed adjustment from transmitter.5. Close the function.21WFT09 INSTRUCTION
(8). Swash and THR mixing22This function is to adjust throttle and pitch mix function.(9). Cur ve SettingWFT09 INSTRUCTIONThere are 2 kinds of setting, Normal and Advanced.
(10)-(16). PROG. NOR. MIX1-7(17)-(20). PROG. CUR. MIX1-4The mix program is to adjust the flying pose. There are 7series programs with the same set method.There are 4 serious curve mix program, the curve is made up by 2 to 11 point.WFT09 INSTRUCTION23
(21). Throttle needle mixing24Throttle needle is a pre-programmed mix that automaticallymoves an in-flight mixture servo in response to the ThrottleStick imputs for perfect engine tuning at all throttle settings.This function is particularly popular with contest pilots who flyin a large variety of locations, needing regular engine tuningadjustments, and requiring perfect engine response at all timesand in all maneuvers. Also popular to minimize flooding at idleof inverted engine installations or installations with a high tankposition. Not need for fuel injection engine, which do thisautomatically.17. LanguageSetting MethodUse up or down button to select Throttle needle mixing, OK button is to enter editing.Steps:1. Use direction buttons to select editing part.2. Ajust the travels as needed to match your engine by slowly moving the stick to each of the points, then adjusting the percentage at that point until the engine is properly tuned.3.Set curves for other conditions.4. Press EXIT after setting.This function is to select the language, Simplified Chinese and English can be selected.WFT09 INSTRUCTION
1.Model selecttingThere are 10 helicopter models.Setting MethodUse up or down button to select Model selecting, OK button is to enter editing.Steps:1. Use direction buttons to select the model.2. Press OK button.3. Press EXIT after setting.2. Model nameSYS SETTING25This function is to make new names by users.Setting MethodUse up or down button to select Model selecting, OK button is to enter editing.Steps:1. You can edit the underlined letter2. Press OK button to choose the word you like.3. Press EXIT after setting.WFT09 INSTRUCTION
Because of the different receiver modulation PPM/PCM, the transmitter should be accordance with the receiver modulation.Setting MethodUse up or down button to select Modulation setting, OK button is to enter editing.PPM and PCM is selectable.4.Modulation settingAdjustable travel limit (ATL) makes the channel 3 TRIM LEVER (THROTTLE TRIM) effective only at low throttle, disabling the trim at high throttle. This prevents pushrod jamming due to idling trim changes. This function defaults to ON. If you are not using channel 3 for throttle, youmay want trim operation the same as on all other channels. To do so, set ATL to OFF.Setting MethodUse up or down button to select Model selecting, OK button is to enter editing.Steps:1. Use direction buttons to select the model.2. Press OK button.3. Press EXIT after setting.3.ATL26WFT09 INSTRUCTION
5.Swash select27Setting MethodUse up or down button to select Model selecting, OK button is to enter editing.Steps:1. Use +/- buttons to select the model.2. Press OK button to choose.3. Press EXIT after setting.There are 6 kinds of swash. You can select the swash you preferred.WFT09 INSTRUCTION
6.Stick settingThere are 4 kinds of model, you can use up and down direction button to select the model you preferred.Setting MethodUse up or down button to select Stick setting, OK button is to enter editing.Steps:1. Use up and down direction buttons to select the model.2. Press OK button to choose.3. Press EXIT after setting.28WFT09 INSTRUCTION
This function is to back default.Setting MethodUse up or down button to select Reset setting, OK button is to enter editing.You can select cancel or OK.8.Rest settingThis function is to set responses in case of loss of signal or low RX battery.Setting MethodUse up or down button to select Fail safe, OK button is to enter editing.Steps:1. Use direction buttons to select editing part.2. Choose Channel to change.3.Set and confirm fail safe conmmand.4. Press EXIT after setting.7.Fail safe29WFT09 INSTRUCTION
9. Send dataThis function is to send the model parameter to another transmitter. By using a trainer cord, one transmitter cansend the data to another transmitter.Setting MethodUse up or down button to select Send data, OK button is to enter editing.Steps:1. Select the model data you need to send out.2. Press OK to send.30WFT09 INSTRUCTION
10.Receive dataThis function is to receive the model parameter to another transmitter. By using a trainer cord, one transmitter canreceive the data from another transmitter.Setting MethodUse up or down button to select Receive data, OK button is to enter editing.Steps:1. Press OK to receive data.2. Restart the transmitter after receiving the data.WFT09 INSTRUCTION31
14.LanguageThis function is to select the language, Simplified Chinese and English can be selected.13.About12.Engineer modelThis function is to adjust the LCD brightness by increasing or decreasing the contrast value.Setting MethodUse up or down button to select Contrast setting, OK button is to enter editing.Steps:1. Use +/- button to increase or decrease the value.2. Press OK button for a while is to back default. 3. Press EXIT after setting.11.Contrast setting32WFT09 INSTRUCTION
TO THE PILOT33 WFT09 is the first version. Thank you for using theradio. We welcome your valuable advice and we will make progress of the radio. Welcome to contact us! www.wflysz.com sales@wflysz.com Tel: 0086 755 26581817 Fax: 0086 755 26581821WFT09 INSTRUCTION

Navigation menu