Shen Zhen WFLY Technology Development WFT07 RADIO CONTROL SYSTEM User Manual

Shen Zhen WFLY Technology Development Co., Ltd. RADIO CONTROL SYSTEM Users Manual

UserManual.wiki >

Shen Zhen WFLY Technology Development >

WFT07 User Manual

User Manual

www.wflysz.comCHANNELS7INSTRUCTION MANUAL V1WFT07 2.4GHZ MULTI-LANGUAGE REMOTE CONTROL DEVICE▲ pls read the instruction before using the product ▲ Please keep this manualAttention

WFT07INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEThank you for purchasing the WFLY productFeatures1.The large dot matrix LCD display: multi-language, graphical display. simple design, easy operation.2.Original 2.4G technology : use of data transfer, greatly improve the handling agility. fully express the fast Lightning : (Note: is WFLY exclusive technology).3.Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries , 4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.4.Super anti-interference: the high spread spectrum (DSSS) + frequency hopping, can boot the 60 sets at same time without interfere.5.Optimization features into the design, operation .Service1.The WFLY warranty the quality of science and technology within a year (WFLY technology to bear the postage, the user must provide a warranty card and proof of purchase,Indispensable).2.Warranty card and proof of purchase effective by signed and sealed by the seller , and the information must be completed.3.Artificially damaged and over one year after the warranty period, the WFLY provide life long science and technology service,only the users pay return postage, materials fees and maintenance costs.4.This warranty is limited to China's remote control and accessories sales .5.Seller does not give warranty card or do not fill out required from the seller to bear all the after-sales service.

112345678991011131313141415151516161717181819191920202121222323ⅠWFT07 Remote control device contentsWFT07 Remote control device WFT07 RC device parts of the name(front)WFT07 RC device parts of the name( back) Instructions of the 2.4Ghz receiverWFT07 code match instructionsTrainer functionSpecial symbal instructionsWFT07 RC device characteristicsExpress of input and buttonsAdjustment of stick headReplacement throttle handHelicopter FunctionsSystem SettingsInput mode and Functions1.Model parameters2.Model Settings3.4.Control stick settings5.Control stick Calibration6.7.Tone settings8.Contrast settings9.Power supply scheme10.Version informationCoaching / SimulationRestore factory settingsPreferences1.Monitor2.Dual Rate 3.Servo Reverse4.End point5.Sub trim6.Trim settings7.Throttle curve settings8.Pitch curve settings9.Throttle cut settings10.Throttle holding settings11.Timer12.Swashplate13.Gyro sens mixing14.Advanced settingsCONTENTSINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

2627272727272727272727272727272727272828282929292929293030303131Ⅱ242425CONTENTSAdvanced settings1.Speeder mixing2.Fail safe3.code matchsystem settingsAirplane FunctionsInput mode and functions1.Model parameters2.Model settings3.4.Control stick settings5.Control stick calibration6.7.Tone settings8.Contrast settings9.Power supply scheme10.Version informationCoaching / SimulationRestore factory settingsPreferences1.Monitor2.Dual Rate3.Servo Reverse4.End point5.Sub trim 6.Trim settings7.Flaperon mixing8.Flap trim9.Aileron diff control10.Elev-flap11.Throttle curve settings12.Throttle cut settings13.Throttle holding settings14.Timer15.Advanced settingsAdvanced Settings1.Elevator mixing2.Ele-Aileron mixing3.V-tail5.Ail-26.Fail safe7.Code matchINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

11.WFT07 remote control device 2. WFR07S 2.4Ghz rece ive3.Simulat or switch cable 4.Transmitter 4cell battery case5.Manual 6.WFLY neck strap1.WFT07 remot e control device 2.WFR0 7S 2.4Ghz receive 3.Si mul ator switch cable Man ual4.Transmitter 4cell battery case 6.WFLY neck strapWFT07 Remote control device contentsWFT07 remote control device diagramINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE www.wflysz.comCHANNELS7INSTRUCTION MANUAL V1WFT07 2.4GHZ MULTI-LANGUAGE REMOTE CONTROL DEVICE▲ pls r ead the in struction befo re using the product ▲ Ple ase keep this manu alAttentio n5.Man ual/CD- ROM 1 set1 Root1 This/zhang1 Only1 A1 Article

K1 K2 K3 K4V12Antenna(rotatable)Power light RF lightBuzzerElevator trimRudder/elevator stickRudder trimThrottle trimAileron/throttle stick Power switchNeckstrap attachmentAileron trimLeftUpRightDownMenuExit Add Reduce LCD OKK1: 2 stalls. Throttle holding and throttle cut K2: 3 stalls. Timer , airplane 5channel and airplane Elev-flap mixing.K3: 2 stalls. Dual rate, Fight mode (normal,special IDLE) K4: Trainer. 7channelsWFT07 RC device parts of nameINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEWFT07 RC device Positive(Right hand throttle)

3WFT07 RC device back WFT07 RC device parts of nameTrainer/DSCHandleBattery coverINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

4Instruction of 2.4Ghz receiverModel:WFR07SType: 7channel 2.4Ghz receiver,4096 resulotion(in the PCMS 4096 resolution) (Adaptation WFLY 2.4Ghz series),ORGANIC 2.4GVoltage :4.8V-6VCurrent:30mAWeight:9.6g Size: 40.42mm x27.27mm x11.88mmFrequency: 2.400GHz-2.483GHz1．AIL：Aileron2．ELE：Elevator3．THR：Throttle4．RUD：Rudder5．GRY： Landing Gear/Gyro 6．PIT： Pitch7．Auxiliary channel(Channel 1)----------(Channel 2)----------(Channel 3----------(Channel 4)----------(Channel 5)----------(Channel 6)----------(Channel 7)----------WFLY PCMS receiver cam compatible with PCMS 4096, PCMS 1024 and PPM modulation(Adaptive), and have fail safe function.ORGANIC 2.4G(Note: Any channel can be used as power input)INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

5WFT07 instructions of the code match1.Remote control device settings●unction instruction:The remote control for the 2.4G spread spectrum, address identification code information, Before frequency hopping systems, have high anti- use the remote control,pls match the code with the interference. The remote control has unique 2.4Ghz receiver.●SettingsInto the "Advanced Settings" menu item under the process needs within a short distance. 2.4G "Preferences" . Press confirm button to enter the module system in the closed state is not available, "code" interface in the "Advanced Settings" . As please refer to “ Once Code above. The specific settings as follows: 1. The successfully will return to the menu. Also can press first use the button to select on the code, the code "exit”button to return.Coaching / Simulation”WarningWhen using this function, please ensure that no other remote control operating!2.Receiver SettingsRemote control device into this interface:Then going receiver settings: receiver hold "SET" button until the STATUS indicator light flashes slowly, waiting for the transmitter of the code instructions. (WFR07S/WFRO9S operating are same)LED Slow flashing After the success of the code ,the LED light is off, you can normally using.Note: The code required in a short distance.INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

6Trainer FunctionInstruction of the Training functionThe same two re mote contro l devices WFT07 can do the Trai ner functio n:INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE1. Using the simulator cable to connect two WFLY equipment.2. Trainer settings: Press MENU key to boot into the "System Settings" function, enter " Training / simulation "menu,selected the" trainer mode ", (effect after re-boot ).3. Student machine setting: Press MENU key of the another radio into the "System Settings" function, entry "Training / simulation "menu,selected the " Simulator Mode ", (effect after re-boot ).4. Release Trainer switch K4, this time the student machine does not sending signal, the operation completed by the trainer.Advance push the trainer switch K4, then operation completed by the Student machines now.Settings:

● Large graphic dot matrix LCD display, easy to operate. ● Multi-language● WFT07 RC device is the multi-function proportion of 7ch remote control . ● The original 2.4G technology , with data transfer , which greatly improve the handling agility Fully explain the fast as lightning. (Note: The is the WFLY exclusive technology).● Low-voltage design, lower battery consumption, a variety of battery available:such as 4S alkaline batteries , 4S NiMH(Nickel Metal Hydride),1S lithium-ion battery ,1S lithium polymer battery . Voltage range 3.7V-6V.● joystick of elastic, are free to adjust the hength of the head. The new shape of the head makes a good Feel. ● Digital electronic tuning, 250 steps adjustable.● Complete the timer function to ensure flight foolproof● Monitor function can more intuitive operation. ● Training function● Perfect timing function● Up to 11 groups of curves, easy to deal with difficult moving actions.● Multiple mixing control system , adjustable 9 point of the curve .● A variety of flight patterns,ease flight.7Note the special symbolFor the safe use of this product, pls pay attention to The marks have the following description of symbols.Dangers:Warnings:Warning:Notices:Note: If you use in without a proper operation,it is possible to hurt user seriously injury or may even cause death .If you use it without proper operation, it may make the user or others to hurt badly or may even cause death,and it may cause slight hurt or damage to things Children under 14 must be accompanied by an adult using If you use it without a proper operation, it may cause user to hurt slightly or damage things,but it won't hurt you seriourly normally. Turn on theTransmitter first, then turn on the receiver; after play pls turn off the Receiver first, then the TransmitterFlight Precautions Prohibitions Compulsory Items Warning※Do not fly in the evening, rain,or strong wind.Possible damage to equipment or aircraft accidents.The Feature of WFT07 Remote control deviceINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

9StickAdjust the height higher:First make the top thread loose with the allen key,then twist the stick head up,then make the top head tighten with allen key.the stick head was turned up.Put the stick head cover the control rod on the left and right sides,don't twist down the stick head to the bottom,and then put top thread with allen key to adjust the height you needed.Adjust the height lower:First make the top thread loose with the allen key,then twist the stick head down,then make the top head tighten with allen key.the stick head was turned down.Twist the top thread down from here,the height of the stick head depends on the depth of the top thread.Steps:1.Put the stick head on the stick.2.Put the top thread in the stick head with allen key.3.Addjust top thread in the stick head with allen key to fix the height of the stick head.Allen KeyTop threadStick Head INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAdjustment of stick head

10Replacement the throttle of mode 1 or 2Bolt 1.Bolt 2.Bolt 3.Bolt 4.Set up release link and springer,according your habit to adjust the tightness of screw 2 to adjust the control felling.Put on the matel chip,according your habit to adjust the elasticity of screw 3 and screw 4 to adjust the damp of throttle control felling.Tak e the metal chip and screw down,and put it on the similar position of the right side.Tak e release link and springDown,and put it on the left side of the location of corresponding,then twist bolt1 down until withstand the adjust nail ,in case adjust nsil will move away.INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICERight-hand man will lose their own free replacement warranty program

122.Function Menu-There are “System settings”,”Preferences”and “Adcanced settings”A. System Settings In close state, hold down the MENU key, then turning on the power, you can enter the "System Settings" menu page, the interface as shown. In this state, all functions can be set one by one. As follows: 1. Use the arrow keys on the screen to select the functions you needed, use up and down keys to select function items. With the left and right arrow keys to flip. 2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific configuration, please refer the next chapter. 3. When Settings finished, press EXIT key to return to superior menu,it will automatically store the Settings value.B. Parameter Settings In the boot screen, press the MENU button on the left screen, you can enter the "settings" menu page, the interface as shown. In this state, the machine can be set one by one the various functions. As follows: 1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to select function items. With the left and right arrow keys to flip. 2. In the functional state ,press OK key to enter sub-menu of the function. The function of specific configuration, please refer the next chapter. 3.When Settings finished, press EXIT key to return to superior menu,it will automatically store settings Value.C. Advanced Settings Into the "Preferences" menu, use the left and right arrow keys to flip, can see the "Advanced Settings" function key. Click OK key to enter. In this state, the machine can be set one by one the various functions. As follows: 1. Use the arrow keys on the screen to select the functions you needed, use up and down arrow keys to select function items. With the left and right arrow keys to flip. 2. In the functional state , press OK key to enter sub-menu of the function. The function of specific configuration, please refer the next chapter. 3.When Settings finished, press EXIT key to return to superior menu, it will automatically store settings Value.Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

13System Settings Menu Introduction1.Model Parameters●FunctionModel parameters function totally have three any of them model to settings.machines for the user to choose, you can select ●SettingsPress the MENU button to boot into the “System The steps of setting is as follows:Settings" menu, use Up / Down keys to 1. Using the up / down keys to select different select the "model parameter settings", and models.press the “OK ” key into the function interface, 2. Selected the options, press OK key to select .as shown above. 3. Settings successfully, press EXIT key to exit.2.Model SettingsModel settings can be used to set to the helicopters, airplane as you needed.●Function●Settings Press the MENU button to boot into the "System The steps of setting is as follows:Settings" menu, use Up / Down keys to select 1. Up / Down keys to select the model."Model Settings", press the OK key into this 2. Click OK key to confirm.function interface, as shown above. 3. Settings finished, press EXIT key to return to 3.Coaching / Simulation◆Normal: normally use the model, RF 2.4GHz the switch K4 is sending the student machine work, do not support the trainer. signal.◆Trainer mode: use the unit as a trainer, use the ◆Simulator Mode: This mode will turn off RF 2.4G training cable connect the other one as a student in order to facilitate learning with other remote machine. through the unit RF 2.4G machine control. Or connect with the computer to simulate control,with the K4 switch. Not switch K4 is the flight to reduce power consumption to increase sending the trainer machine signal, when push the use of time.●FunctionNote: For security, the above mode switch to take e ffect after reboot.Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

14图3●SettingsPress the MENU key to boot into the "System 1, first to use the up / down arrow keys to edit the Settings" menu,use Up / Down arrow keys to selected item.select the "trainer / Simulator", press OK key to 2. Press OK button to confirm, then press the right enter the function interfacet, as shown above. arrow keys to determine. Reboot to take effect.The steps of setting is as follows:4.Control Stick Settings●Function●SettingsControl stick settings function allows users Totally have four models to choose .to freely setting the higher of the stick according to personal preferences . As shown. This machine Press the MENU key to boot into the "System 1. First to use the arrow keys to select the edited Settings" menu,use Up / Down keys item .to select the "stick settings" and press OK key to 2 Use Up / Down key to implementation Stick Mode . enter this function interface, as shown above 3. Set successfully, press EXIT key to exit. The steps of settings is as follows: 5.Stick CalibrationJoystick calibration function allows users to preferences .change the throttle side according to personal ●Function●SettingsPress the MENU key to boot into the "System (throttle /elevator on the top edge, aileron / rudder on the Settings" menu,use Up / Down keys to select right edge), press the OK key (in this case the maximum "Stick calibration" and press OK key to enter the value has been calibrated), into the stick minimum (low) function interface, as Shown above. Specific calibration. 5.When the "low" highlighted, put the stick settings, follow these steps: 1.First to use the arrow gently leaned on the left (throttle / elevator on the lowest, keys to select the edited item, (example aileron Aileron / rudder on the left edge), press the OK key (while calibration). 2.Put the calibrate joystick placed in the the stick minimum calibrated OK). 6.At this memont the midpoint of the channel position, options Up / Down - bottom of the screen displays "confirmation / reset" and key implementation the control calibration . 3.Selection press to OK key ,all the calibration is completed, into the Figure 3. When the "middle" highlighted, press automatically return to the superior menu, use the OK key (this time the Point calibrated is OK), into the arrow keys selected to re-enter Calibrationstickmaximum (high) calibration. 4.When the "high" Procedures.highlighted, put the stick gently leaned on the right 1---ileron2---evator3---hrottle4---RudderHelicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

156.Restore factory settings●Function●SettingsReset function is to present the model all the Comprehensive settings of re-work.data back to the initial default settings, so can do Procedures.Press the MENU key to boot into the "System 1. First to use the arrow keys to select the Settings" menu, use Up / Down keys to select Edited item."reset ", press Confirm key into the function 2. With + / - key to implementation the reset.interface.As above: 3. Set successfully, press EXIT key to return.The steps of settings is as follows:7.Tone Settings●Function●SettingsTone settings allows users to freely set all the Preference.sounds on or off according to personalPress the MENU key to boot into the "System The steps of settings is as follows:Settings" menu, use Up / Down keys to select 1. Into the items, press OK key to select the sound "Sound", press the OK key to enter the function on or off.interface, as above. 2. Automatically saved after confirmation.8.Contrast Settings●Function●SettingsThe contrast setting function can increase or decrease the contrast value to adjust the brightness of the display , change the brightness of the screen.Press the MENU key to boot into the 1. Using the + / - keys to set the value of "System Settings" menu,use Up / Down increase / decrease.keys to select "Contrast settings" and 2.Long time press OK key restore the default press OK key to enter the function value.interface ,as above. 3. Set successfully, press EXIT key to return.The steps of settings is as follows:Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

169.Power supply scheme●Function●SettingsThe machine can use a variety of power options: If ordinary alkaline AA batteries 4S, Ni-MH / Ni-Cd battery 4S, Li-Ion / Li-polymer battery 1S. Different battery in different low-battery voltage alarm, in order to extend battery life, select the corresponding power supply plan.Press the MENU key to boot into the "System 1. The first to use the arrow keys to edit the selected Settings" menu,use Up / Down arrow keys to item.select "Power Information", press OK button to 2. Select the power scheme with the + / - key to enter the function interface. As shown above. The implementation.steps of setting is as follows: 3. Set successfully, press EXIT key to exit.10.Power supply schemeNote:Voltage range 3.7V-6V.Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

Introduction of the Parameters Settings Menu1.Monitor●Function●SettingsThe monitor function is to monitor and confirm the channel operation state.In the "Preferences" interface, use Up / down keys each channel action conditionto select the "Monitor", press OK key to enter the function interface, as above.Then can monitor 2.Dual Rate Settings ●Function●SettingsDual Rate function is by setting the switch to control rate.change the aileron, elevator, and rudder of the In the "Preferences" interface, use Up / down keys 3. Settings the D / R, Use the arrow keys to select to select the "Dual rate ", press OK key to enter the the "D / R 'in screen, when the screen light off, the function interface . As above.then enter the edit mode of this function. The steps of settings is as follows (You can choose settings single parameter or two 1. Select the required channel (eg, aileron, parameters at the same time ), then press + / - keys elevator etc.). Use the + / - key to select the to change the values ,long press OK key can be required channel, confirmed with OK key. recovered to the default value. 2. Select the K3 switch position (position 0 or position 2). Use the + / - button to select the required location . Cur ve poi nt and Cur so r lineSel ec t ac tion(Ai leron, Elevator,Rudder )Switch K3End poi ntExpon ent ialCur ve poi nt displayCur ve17CH 1CH 2CH 3CH 4CH 5CH 6CH 7Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

185. Use the arrow keys to select the curve point, + / 6. Set successfully, you can press EXIT key to - key to changing the value of curves point. return.4. Settings exponential EX, can change the combinations and settings, with the arrow keys to aileron, throttle and rudder these three channels' select the "EX" in the screen, settings way are same joystick sensitivity near the neutral. Dual rate and as "D / R" . curve exponential are match, will have a lot of 3.Servo Reverse●Function●SettingsServo reverse function can adjust the direction of movement is normal or reversed.the servo moves to make the direction of servo In the "Preferences" interface,use Up / Down keys item.to choose "Servo reverse", press OK key to 2. with + / - keys to switch the action is normal or confirm enter the function interface.As above.The reverse and use the OK keys to implement.steps of settings is as follows: 3. Set successfully, press EXIT key to return.1. First to use the arrow keys to select the edited 4.End Point●Function●SettingsEnd point function can determine the end point of route of servo movements, the adjustment range is the servo's initial value, adjusting the largest between 0% -120%.In the "Preferences" interface,use up / down keys keys to select the edited items.to select the "End point" and press OK key to enter 2.Set the value of the route with + / - key. Long press the function interface, as above. The steps of OK key to restore the default values.3. Set successfully, press EXIT key to return.settings is as follows: 1.First use the arrow Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

●FunctionThrottle curve with the throttle stick position to with the pitch can achieve the best effect. Stunt adjusted the engine flight in the best state. This Curve is maintaining a certain engine speed,make throttle curve can set to normal and stunt curves the throttle with the pitch to complete the stunts in and so on.The operation of those curves can the flying .carried out by the switch.The throttle curve of normal curve is basic on hovering, the engine rpm 195.Sub Trim●Function●SettingsWhen the electronic trim can not make the servo ideal angle which user wanted. When set this to achieve a satisfactory angle, be corrected by function , please place the trim in the central the function, can make the servo to reached a location, then start settingIn the "Preferences" interface,use Up / Down keys 2. Set the amount of the sub trim of movement with to select the "Sub trim", press the OK key to the + / - keys or used the OK key to implement, long confirm you access in this interface, as above. press the OK kay can restore the default value.The steps of settings is as follows: 3. Set successfully, press EXIT key to return.1. First to use the arrow keys to select the edited item.6.Trim Settings●Function●SettingsTrim settings function is adjustment for each trim be 1-250.to change the trim sensitivity, settings amount can In the "Preferences" interface, use Up / Down item.keys to select the "Trim" and press OK key to 2. Set the amount of Trim with the + / - key,use OK confirm access in this function interface, as key to implement. If "reset", can set the trim location above The steps of settings is as follows: value to zero.1. First to use the arrow keys to select the Edited 3. Set successfully, press EXIT key to return.7.Throttle Curve SettingsCurve pictureFlight ModeDual rateExponentia Curve point Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

20●SettingsIn the "Preferences" interface,use Up / Down keys choose individual settings on one or setting on both to select the "throttle curve settings", press OK sides ), Press the + / - keys to set the values,long key to confirm enter the function interface, as press the OK key to return to the default value.above. 3. Use left and right arrow keys to select curve The steps of settings is as follows: points, + / - keys to change the value of curve points.1. Flight status (normal or stunt). Use the arrow 4. Set successful, you can press EXIT key to return.keys to enter edit state, you use + / - keys to select one of the curve, then enter the following settings.2. Set the D / R, Use the arrow keys to select the "D / R"in the screen, when the screen light off, then enter the edit state of this function(you can 8.Pitch Curve SettingsCurve pictureFlight ModeDual rateExponentia Curve point ●Function●SettingsPitch curve with the throttle stick position can curve is based on hovering, as a certain engine rpm adjusted the engine rpm flight in the best state, to adjust the pitch to the best place . Stunt pitch This pitch curve can be set normal, stunt and lock curve is maintaining a certain engine rpm, make the curve and so on. The operation of those curve can pitch with the throttle to complete stunts in flying.carried out by the switch.Pitch curve of normal Pitch curve with the throttle stick position can curve is based on hovering, as a certain engine rpm adjusted the engine rpm flight in the best state, to adjust the pitch to the best place . Stunt pitch This pitch curve can be set normal, stunt and lock curve is maintaining a certain engine rpm, make the curve and so on. The operation of those curve can pitch with the throttle to complete stunts in flying.carried out by the switch.Pitch curve of normal 9.Throttle Cut Settings●FunctionThrottle cut settings function is to make the when implement the action. So when moving the engine off when the flight finished. Switch K1 is for throttle trim,have to check the throttle closed action opening and closing the throttle. Throttle trim position .adjustment will affect the throttle closed position Settings and Notes:When the throttle closed the throttle turn off the function of the best range of switch move to open, can adjust the value until the motion is to set near the engine speed .carburetor valve fully closed (engine shutdown). To prevent the error in the adjustment operation, Warning:●SettingsIn the "Preferences" interface,use Up / Down keys a + / - key to implement.3.Under the throttle cut to select the "throttle cut settings", press OK key condition, the rate of value and trim amount can to confirm enter the function interface, as above. settings with + / - key to the implement (adjustable The steps of settings is as follows: range of ± 45%).4. Set successfully, press EXIT key 1, the first to use the arrow keys to select Edit to return.Item2. Throttle cut settings function on or off with Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

2110.Throttle holding Settings●Function●SettingsThrottle holding settings can set in when throttle adjustment within ± 75% .cut landing , fixed the throttle servo in the a low Switch K1 work for this function.speed position , throttle holding position can be In the "Preferences" interface,use Up / Down keys function , with + / - keys to implement.. 3. In the to select the "throttle holding settings", press OK "Location" item to set the throttle holding location, key to confirm enter the function interface, as with a + / - key to implement. Long press OK key to above. The steps of settings is as follows:1, the restore the default values. 4. Set successfully, press first to use the arrow keys to select Edited Item.2. EXIT key to return.. In the "mixing" item to set on or off this mixing 11.Timer●Function●SettingsAs the different of each Helicopter fuel tank size alert with short-ring ,when from 10 seconds to the and engine speed, will lead to vary different flight time,each second alert with long-ring, regular time.The Timer function can alert you in warning arrival will blew tips.tone landed the plane safely on the ground before ◆ can set the timing and countdown.you used up the fuel . ◆ Control way : K2 switch control, throttle control, ◆The maximum time of the timer is 99 minutes automaticel work after boot.and 59 seconds. In the work every 1 minute to tips time, from 20 seconds to the time, each second In the "Preferences" interface,use Up / Down key to restore the default value.keys to select the "Timer", press OK key to 4. In the "mode" item set mode. With a + / - key to confirm enter the function interface, as above. implement.The steps of settings is as follows: 5. In the "Control"item set the control switch, with + / 1, First to use the arrow keys to select Edited - key to implement.Item. 6. In the "position" item set the throttle control 2. In the "Timer" item set the timer. location. With a + / - key to implement.3. In the "minutes ..seconds .. " option to set the 7. Set successfully, press EXIT key to return.time, with a + / - key to implement. Long press OK Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

2212.SwashSwash type selection●Function●SettingsIf using a helicopter with CCPM, connecting a remote control device offers two modes: normal, cross-shaped piece of servo will automatic going and 3CH120 (CCPM) mode. As abovethe mixing action. Please use the helicopter swash according to the type of choice. This In the "Preferences" interface,use Up / Down keys press OK key to enter.to select the "Swash", press OK key to confirm 2. Selected swash type selection press OK key to enter the “Swash type selection “interface, as enter, with + / - key to implement the selection mode.above. 3.. Set successfully, press EXIT key to return.The steps of settings is as follows:1. First to use the arrow keys to select the Swash, Swash Parameter adjustment●Function●SettingsSwash parameter adjustment function is selected pitch three parts .the swash type for adaptation the aileron elevator, In the "Preferences" interface,use Up / Down keys to enter.to select the "Swash", press OK key to confirm 2. Selected the swash parameter adjustion press enter the “Swash type Adjustment“interface, as OK key to enter, with Up/down key to implement the above. selection.use +/ -- Key to adjust the parameters.The steps of settings is as follows:1. First to use 3.. Set successfully, press EXIT key to return. the arrow keys to select the Swash, press OK key Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

2313.Gyro Sens Mixing●Function●SettingsCan adjust the gyro sensitivity directly from the 5channel in front of the auxiliary channel setting is transmitter, you can choose AVCS gyro (GY) and temporarily non-functional,switch sensitivity by ordinary gyro (STD). Gyroscope sensitivity switch flight mode (Normal stunt lock) .plugs into the 5 channel of the receiver. This time Into the "Preferences" under the”Advanced function, use + / - key to implement. Long press OK Settings” menu,use Up / Down keys to select the" key to restore default.gyro sens mixing "function , press the OK key to 4. In the "position" option to set the control position enter the function interface. As above. Specific on or off this function, with a + / - key to implement.settings steps are as follows:1. First to use arrow 5. In the "ratio" option set the mixing value, with + / - keys to enter the edit mode. key to implement. Long press OK key to restore the 2. In the "mode" option set flight mode, With a + / - default value.key to implement. 4. Set successfully, press EXIT key to return.3. In the "mixing" options settings on or off this 14.Advanced Settings●Function●SettingsThis machine for allowing users to achieve more Interface as shown. The purpose of each function satisfactory flight effect, added some special will be introduced in the followingfeatures in the "Advanced Settings" function.In the "Preferences"interface,use Up / Down turn the pages, press the + / - keys to select the keys to select "Advanced Settings" and press OK function item. The specific function and setting key to enter the function interface, as above. method. Please refer below.In this state, press left and right arrow keys can Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

24Introduction of Advanced Setting Menu1.Speeder Mixing Settings●Function●SettingsSpeeder mixing settings is under the case have state can set the output action servo.the speeder, uses and settings the speeder . In the Into the "Preferences" under the Advanced 2. In the "mixing" option to set the on/off of the Settings "menu.use Up / Down keys to select the" mixing functions, with + / - key to implement. Speeder mixing settings ", press the OK key to 3. In the "ratio" option set the mixing value, with + / - confirm enter the interface. The steps of settings key to implement. Long press OK key to restore the is as follows: default value. 1. First to use the arrow keys to enter the edit 4. Set successfully, press EXIT key to return.mode. 2.Fail Safe●Function●SettingsFail safe function is used for various reasons automatically return to the default values position or (such as interference,long distance), the receiver maintain the current value of the function.will lost the transmitter signal,and the receiver will Press the MENU key to boot into the item . "Preferences" menu, use Up / Down keys to 2. With a + / - key to maintain the settings / specific choose "Fail safe" and press OK key to enter the position. function interface, as above . Can not use this 3. Click OK key, can be deposited the current actual feature when the 2.4 G module in close state. channel parameters. The steps of settings is as follows: 4. Set successfully, press EXIT key to return.1.First to use the arrow keys to select the edited Warning :When using this feature, please ensure that no operation of other remote control!Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

253.Code Match●Function●SettingsThis remote control are the 2.4G spread identification code information, before you use the spectrum, frequency hopping systems, with a high remote control system pls matched with the 2.4G anti-interference. Each remote control only has an receiver which including in this device.Into the "Preferences" under "Advanced settings" the process of the code needed within a short menu. Press OK key to enter the “Code “interface distance. 2.4G module system in the closed state is under the "Advanced Settings" . As above. not available, please refer to "modulation type." Specific settings following these steps: Once the code successfully will initiative to return to 1. First to use the arrow keys to select the” code”, the menu. also can press "exit” Key to Quit.Warning When using this feature, please ensure that no operation of other remote control! Helicopter FunctionsINSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICE

Selection Refer the instroduction on page 17Selection Refer the instroduction on page 17Selection Refer the instroduction on page 18Selection Refer the instroduction on page 18Selection Refer the instroduction on page 19Selection Refer the instroduction on page 191 Monitor2 Dual rate 3 Servo reverse4 End point5 Sub trim6 Trim277.Flaperon mixing●Function●SettingsThis feature is to use two mixers in the aileron, to make aileron have a mixer like flap function.Press the power button to boot into the / down keys can choose to the edit item."Preferences" menu,use Up / Down arrow to 2. Selected the options, press the + / - key to edit the select the "Flaperon mixing", press OK key to data. Long press OK key to restore the default enter the function interface, as above. values. The steps of settings is as follows:1. Using the up 3. Set successfully, press EXIT key to retrun.Introduction of System Settings MenuIntroduction of Parameter Settings Menu1.Model parameters 2.Model Setting3.4.Stick settings5.Stick calibration6.7.Tone settings8.Contrast settings9.Power supply scheme10.Version InformationCoaching / SimulationRestore factory settingsSelection Refer the instroduction on page 16Selection Refer the instroduction on page 16Selection Refer the instroduction on page 15Selection Refer the instroduction on page 15Selection Refer the instroduction on page 15Selection Refer the instroduction on page 14Selection Refer the instroduction on page 14Selection Refer the instroduction on page 13Selection Refer the instroduction on page 13Selection Refer the instroduction on page 13INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAirplane Function

288 Flap trim ●Function●SettingsThis feature is for 6 channels to do the trim stick action.Press the power key to boot into the "parameter item.settings" menu, use Up / Down keys to select the 2. Selected the options, press the + / - key to edit the "Flap trim", press OK key to enter the function data. Long press OK key to restore the default interface, as above. The steps of settings is as values.follows: 3. Set successfully, press EXIT key to return.1. Using the up / down keys can choose to the edit 9 Aileron diff control ●Function●SettingsThis feature is used in have two aileron servo, you can create the differential aileron movement.Press the power button to boot into the "parameter 1. Use the up / down key to select the Edit Itemsettings" menu,use Up / Down keys to select the 2. Selected the options, press the + / - key to edit the "Aileron diff control", press OK key to enter the data. Long press OK kry to restore the default value.function interface, as above. The step of settings 3. Set successfully, press EXIT key to return.is as follows:10 Ele-Flap Mixing●Function●SettingsThis feature is to make the flap, elevator doing the make the stunt movement more fluid . K2 controls corresponding action. Flap down, elevator up, the switch.Press the power button to boot into the 1. Using the up / down keys to choose the edit item."Parameter setting" menu, use Up / Down keys to 2. Selected the options, press the + / - key to edit the select the "Ele-flap mixing", press OK key to enter data. Long press OK key to restore the default the function interface. As above. values. The step of settings is as follows: 4. Set successfully, press EXIT key to return.INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAirplane Function

29Advanced Settings Menu1.Elevator Mixing●FunctionThis feature is generally applicable to the Elevon aileron, elevator action volume independently.mixed by aileron and elevator , Can adjust the Notes:The three of Elevon, V tail, elevator function can not be open simultaneously. Also Ele --Aileron, flaps, aileron diff is also only can use one function, can not be open when the other functions working, this feature will show " warning "Please forbid the other mixing, and then turn on this feature. As shown on the right●SettingsInto the "Preference Settings" under "Advanced 1. Using the up / down keys to choose the edit item. Settings" menu , use up / down keys to select the 2. Selected the options, press the + / - key to edit the "Elevator mixing", press OK key to enter the data. Long press OK key to restore the default function interface, as above. values. The step of settings is as follows: 2. Set successfully, press EXIT to return.11 Throttle Curve Settings12 Throttle Cut Settings13 Throttle Holding Settings14 TimerSelection Refer the instroduction on page 19Selection Refer the instroduction on page 20Selection Refer the instroduction on page 21Selection Refer the instroduction on page 21INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAirplane Function

302.Ele-Aileron Mixing●FunctionThis feature is to allow elevator to work in the aileron mixing function.Notes:Ele--aileron mixing, V-tail , Ele- flaps can not be "warning", please forbid the other mixing functions, opened simultaneously, if the screen displays then turn on this function.●SettingsInto the "Preferences settings" under "Advanced item.Settings" menu .use Up / Down keys to select "Ele 2. Selected the options, press the + / - key to edit the - aileron mixing", press OK key to enter the data. Long press OK key to restore the default function interface . As above. values.The steo of settings is as follows: 4. Set successfully, press EXIT key to return.1. Using the up / down keys to choose the edit 3.V-Tail Mixing●Function●SettingsThis feature is use for V-tail aircraft the elevator and rudder mixing function.Into the "Preferences Settings" under "Advanced down keys to choose the edit item.Settings" menu.use Up / Down keys to select "V- 2. Selected the options, press the + / - key to edit the tail mixing" and press OK key to enter the function data. Long press OK key to restore the default interface. As above. values.The step of settings is as follows:1. Using the up / 3. Set successfully, press EXIT key to return.INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAirplane Function

314.Aileron-2●Function●SettingsAileron -2 is aileron another channel 's distribution.Press the MENU key to boot into the "System The step of settings is as followsSettings" menu, use Up / Down keys to select the 1. Using the + / - keys to choose different models."aileron -2", press the OK key to enter this function 2. Selected the options, press OK key to confirm.interface, as above. 3. Set successfully, press EXIT key to return.6 Code Match ●Function●SettingsThis remote control is the 2.4G spread spectrum, identification code information, before you use the frequency hopping systems, with a high anti- remote control system pls matched with the 2.4G interference. Each remote control has unique receiver including in the device.Into the "Preference Settings" under "code" menu short distance. 2.4G module system can not use this . Click OK key to enter the state of the coding. As function in the closed state, please refer to above “" Once the code successfully The step of settings is as follows: will initiative to return the menu. Also Can press 1. First to use the arrow keys to select on the "Exit"key to quit.code, the process of the code needed within a Coaching / Simulation Warning :When using this function, please ensure that no other operation of remote control!5 Fail Safe Selection Refer the instroduction on page 24INSTRUCTION MANUAL WFT07 REMOTE CONTROL DEVICEAirplane FunctionFCC WARNNING Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment..

SHENZHEN WFLY TECHNOLOGY DEVELOPMENT CO.,LTDThank you for purchasing WFT07 remote control device, pls read the instructions carefully before use it.Room 618-619,6/F Chuangye Building, No.1 Qilin Road, Nanshan District, Shenzhen 518052, P.R.China Tel：+0755-26581815　 Fax：+86-755--26585126 http:// www.wflysz.com Email：sale2@wflysz.com

Navigation menu