Sharp NAR0051 Notebook Computer with WLAN User Manual safety av18

Sharp Corporation Notebook Computer with WLAN safety av18

Contents

Manual revised

 i  Notice for Users in the USA  FCC Statement  WARNING - FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.  Note:  This equipment has been tested and found to comply with the limits for a  Class B digital device pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation.  This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.  However, there is no guarantee that interference will not occur in a particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: •  Reorient or relocate the receiving antenna. •  Increase the distance between the equipment and receiver. •  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. •  Consult the dealer or an experienced radio/TV technician for help.  A shielded I/F cable and included ferrite core for LAN cable is required to insure compliance with FCC regulation for Class B computing equipment.  *  As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.  Declaration of Conformity SHARP PERSONAL COMPUTER, PC-AV Series This device complies with part 15 of the FCC rules.  Operation is subject to the following conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.  Responsible Party:  SHARP ELECTRONICS CORPORATION   Sharp Plaza, Mahwah, New Jersey 07430-2135  TEL: 1-800-BE-SHARP
 ii   About the Modem  This equipment complies with Part 68 of FCC rules.  On the bottom of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment.  If requested, this information must be provided to the telephone company.  The modem jack of this equipment complies with Sub-part F of Part 68 of FCC rules.  The REN is used to determine the quantity of devices which may be connected to the telephone line.  Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call.  In most, but not all areas, the sum of the RENs should not exceed five (5.0).  To be certain of the number of devices that may be connected to the line, as determined by the total RENs contact the telephone company to determine the maximum REN for the calling areas.  If the terminal equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required.  But if advance notice isn't practical, the telephone company will notify the customer as soon as possible.  Also, you will be advised of your right to file a complaint with the FCC if you believe it necessary.  The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of the equipment.  If this happens, the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service.  If trouble is experienced with this equipment, please contact Sharp Electronics Corp.  for repair and (or) warranty information (Refer to the provided Consumer Limited Waranty).  If the trouble is causing harm to the telephone network, the telephone company may request you remove the equipment from the network until the problem is resolved.  The equipment cannot be used on public coin service provided by the telephone company.  Connection to Party Line Service is subject to state tariffs.  (Contact the state public utility commission, public service commission or corporation commission for information.)
 iii  The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to use a computer or other electronic device, including fax machines, to send any message unless such message clearly contains in a margin at the top or bottom of each transmitted page or on the first page of the transmission, the date and time it is sent and an identification of the business or other entity, or other individual sending the message and the telephone number of the sending machine or such business, other entity, or individual.  (The telephone number provided may not be a 900 number or any other number for which charges exceed local or long-distance transmission charges.) To program this information, refer to the manual of the communication software.   Warning This product utilizes tin-lead solder, and fluorescent lamp containing a small amount of mercury.  Disposal of these materials may be regulated due to environmental considerations.  For disposal or recycling information, please contact your local authorities or the Electronics Industries Alliance: www.eiae.org   Copyright It is the intent of Sharp that this product be used in full compliance with the copyright laws of the United States and that prior permission be obtained from copyright owners whenever necessary.  Product Information and Customer Assistance For Product Information and Customer Assistance:    Call:  1-800-BE-SHARP (237-4277)    Sharp Systems of America     5901 Bolsa Avenue, Huntington Beach, CA 92647     Home Page: http://www.sharpsystems.com   E-mail address: ssa-support@sharpsystems.com
 iv   CAUTION:  TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE BATTERY BEFORE SERVICING.  CAUTION: FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN PLUG AND THE BATTERY.  VORSICHT: UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN.  ATTENTION: POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE COURANT SECTEUR ET LA BATTERIE.  VARNING: FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA UR BATTERIET.  PRECAUCION: PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA CLAVIJA DE LA RED Y LA BATERIA.
 v  Safety Precautions  General •  Follow all cautions and instructions, which may be marked, on your computer. •  Except as described elsewhere in this manual, refer all servicing to qualified personnel. Immediately shut off your computer and seek servicing under the following conditions: •  when the power cord or plug is damaged or frayed •  when liquid has been spilled on your computer •  when your computer has been dropped or the cabinet has been damaged  Location •  Do not expose your computer to direct sunlight. •  Try to avoid dusty environments. •  Keep your computer away from any magnetic devices and TVs. •  Keep your computer away from excessive humidity or fluids such as rain, snow, water spray, juice, coffee, steam, etc.  •  Do not move your computer from an extremely cold place to an extremely warm place.  A temperature difference of more than 10°C (18°F) will cause condensation inside the unit, which may cause damage.  •  Do not block or cover slots or openings on the cabinet. They protect your computer from overheating. •  Do not place your computer on an unstable or uneven work surface. •  Care should be exercised when using on heat sensitive surfaces or your lap as the base of your computer will get hot. •  Do not use your computer on your lap or any part of your body for an extended period during operation or charging to avoid injury from heat exposure.   Usage •  Never push any kinds of objects into cabinet openings. They may touch dangerous voltage points or short parts that could result in fire or electrical shock. •  Turn off your computer before installing or removing any peripheral devices except when connecting USB devices, an IEEE1394 device, a PC card, etc.
 vi  •  Check the AC power cord and power connectors periodically for damage. Change the power cord immediately if damage is found. •  Never subject your computer to sudden shocks or extreme vibration.  •  Do not drop your computer nor hit it with other equipment. •  Do not scratch the surface of the LCD screen.  •  Turn off your computer and disconnect the AC power cord before cleaning.   Battery Pack Precautions  CAUTION DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS.   Handling •  Never put the battery pack in a fire, as it could explode and cause injury. •  Do not attempt to open or alter the battery pack. •  Do not place the battery where it might get hotter than 60°C (140°F). •  The battery pack must be kept from metal objects such as jewelry and liquids. They might trigger a short circuit and consequently cause the battery pack to heat up and explode. •  Do not allow liquids to come in contact with the battery pack. •  Care must be taken not to drop the pack.  A violent shock damages the pack. •  Do not solder anything to the battery terminals.
 viii  About This Manual  Notice Information in this manual is subject to change without notice and does not represent a commitment on the part of SHARP Corporation and its sales subsidiaries. SHARP Corporation and its sales subsidiaries shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material. SHARP strongly recommends that separate permanent written records be kept of all important data.  Data may be lost or altered in virtually any electronic memory product under certain circumstances.  Therefore, SHARP assumes no responsibility for data lost or otherwise rendered unusable whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired, or any other causes. SHARP assumes no responsibility directly or indirectly, for financial losses or claims from third persons resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss of or alteration of stored data, etc.  Edition 1st Edition, July 2003.  Copyright © 2003 SHARP Corporation This document contains or refers to proprietary information which is protected by copyright.  All rights are reserved.  Copying or other reproduction of this document is prohibited without the prior written permission of SHARP Corporation.  Trademarks AMD, the AMD logo, AMD Athlon, and AMD PowerNow! are trademarks of Advanced Micro Devices, Inc.  IBM is a trademark of International Business Machines Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. Windows Media is a trademark of Microsoft Corporation in the United States and other countries.  WinDVD is a registered trademark of InterVideo, Inc.  Dolby and the double-D symbol are registered trademarks of Dolby Laboratories Licensing Corporation. Power Quest is a registered trademark and EasyRestore is a trademark of PowerQuest Corporation. BAPCo is a registered trademark of the Business Applications Performance Corporation. MobileMark is a trademark of the Business Applications Performance Corporation.
 ix  All other brand and product names are trademarks or registered trademarks of their respective holders.
 x  Recording Important Information  For future reference, please record the following information in the spaces provided below.  Model Number:     Serial Number:     Date of purchase:     Dealer’s Name:     Place of purchase:     Password:    The serial number is printed on a sticker located on the bottom of your computer.
 xi  Manual Conventions  This manual uses a set of style conventions described below.  Notes and Cautions are italicized with icons:  A note icon informs you of a special technique or information that may help you perform a task or better understand a process.   A caution icon alerts you to something that may cause problems or damage to hardware, software or data.  Key Labels on the Keyboard, when referred to in the instructions, are shown in boldface:  Press Enter to continue.  When two or more keys are pressed simultaneously, the key labels are separated by a plus (+) sign:   Restart your computer by pressing Ctrl+Alt+Delete. Sample Entries are shown in lower cases of different typeface.    c:\windows\system  Words/Texts on Screen, such as window titles or possible parameters, are italicized:    Double-click this icon to display the Power Options Properties window.   Set the item to Enabled.  Screens reproduced in this manual may differ slightly from the screens you see on your computer.  Section Titles in other parts of this manual are italicized:  Refer to Installing Battery Pack section of Chapter 1.
  xii Table of Contents  Notice for Users in the USA.......................................................................................i Safety Precautions .....................................................................................................v   About This Manual.................................................................................................viii Recording Important Information..............................................................................x Manual Conventions.................................................................................................xi Table of Contents.....................................................................................................xii Overview of Computer ...........................................................................................xiv  Quick Setup   Installing Battery Pack............................................................................................1-1 Connecting to AC Power Source............................................................................1-2 Setting Up Windows...............................................................................................1-4 Turning Off Your Computer...................................................................................1-6 Basic Operations   Choosing Power Source..........................................................................................2-1 Resetting System ....................................................................................................2-3 Using Glide Pad......................................................................................................2-4 Using Keyboard......................................................................................................2-6 Using Optical Drive................................................................................................2-7 Writing Data to CD-R/RW Disk...........................................................................2-10 Watching DVD Video ..........................................................................................2-11 Controlling Volume..............................................................................................2-15 Adjusting Display.................................................................................................2-16 Sharing Your Computer........................................................................................2-19 Battery and Power Management   Battery Pack............................................................................................................3-1 Optional Add-on Battery Pack................................................................................3-6 Power Management ..............................................................................................3-10
  xiii Peripherals  Using Peripherals....................................................................................................4-1 Optional External Floppy Disk Drive Unit.............................................................4-3 External Display .....................................................................................................4-5 Audio System .........................................................................................................4-7 USB Device..........................................................................................................4-11 PC Card.................................................................................................................4-12 Printer ...................................................................................................................4-14 IEEE 1394 Device ................................................................................................4-15 Communication Functions   Built-in Modem ......................................................................................................5-1 LAN Unit................................................................................................................5-4 Wireless LAN.........................................................................................................5-7 Network Setup Utility...........................................................................................5-11  Setup Utility   Running the Setup Utility .......................................................................................6-1 Main Menu .............................................................................................................6-3 Advanced Menu......................................................................................................6-4 Security Menu.........................................................................................................6-4 Boot Menu..............................................................................................................6-6 Exit Menu ...............................................................................................................6-6 Appendixes Memory Module....................................................................................................A-1 Installing Weight Saver .........................................................................................A-4 Maintenance and Care ...........................................................................................A-6 Re-installation Instructions..................................................................................A-11 Troubleshooting   Index
 xiv  Overview of Computer  Each number after an arrow indicates the page referring to the part. Actual appearance of your computer may be slightly different depending on the model.  Front            LCD Screen →2-16 Keyboard →2-6 Glide Pad →2-4 Power Button →1-3 Battery Indicator →2-1,3-3 Power Indicator →2-1 Antenna Indicator          Status Indicators ANHard DiskNum LockCaps LockScroll LockOptical Drive Antennas
 xv  Right           Left             Rear          Modem Jack →5-2 Volume Control →2-15 PC Card Slot →4-12 Audio Output Jack (S/PDIF Compliant) →4-7,8,9 Microphone Jack →4-10 Ventilation Openings →v USB Ports →4-3,11,14 Optical Drive →2-7 LAN Jack →5-5 IEEE1394 Connector →4-15 AC Adapter Jack →1-2 Security Slot →A-9 External Monitor  Port  →4-6 Ventilation Openings →v S Video Output Jack →2-13
 xvi  Bottom                                    Battery Pack →3-1 Speaker  Reset Switch →2-3
1  1-1  CHAPTER 1     Quick Setup  Your computer is designed and pre-configured for easy setup and use. This chapter describes the steps to set up and run your computer as quickly as possible.  Read this chapter first.  Installing Battery Pack  Your computer is powered with either the rechargeable battery pack or AC power source. See the next chapter for more information on the power sources. Before starting to use your computer for the first time, follow these instructions.  1.  Place your computer with the bottom up on a stable work surface. 2.  Insert the battery pack into your computer by matching the projected parts of the battery pack to the notched parts on your computer.   Notched Part Projected Part
 1-2  1 3.  Push the battery pack until you hear the clicking sound.  4.  Turn your computer over and go to the next section.  Connecting to AC Power Source   •  Always use the AC adapter and AC power cord included with your computer or the optional one (may not be available in some countries). Using others may damage your computer. •  Always hold the AC power cord by the plug when removing it from the wall outlet. Never pull on the cord.  •  Never plug in and out the AC power cord with your wet hands. •  When using your computer for the first time, be sure to operate it on AC power. On battery power instead, you may not be able to complete the Windows setup if the battery does not have enough power.  1.  Plug the AC adapter cable to the AC adapter jack on the rear side of your computer. 2.  Plug the AC power cord into the AC adapter. 3.  Plug the AC power cord into a wall outlet.                         AC Adapter AC Power Cord To Wall Outlet AC Adapter Jack
1  1-3  4.  Slide the display cover lock lever to the right until the display cover releases, and raise the cover.    5.  Press the power button to turn on your computer.      When you turn on your computer, the power indicator ( ) turns green, your computer goes through a self-test to detect any problems, and Windows setup process starts. See the next page.  Display Cover Lock Lever Power Indicator Power Button
 1-4  1 Setting Up Windows  To setup Windows, follow the instructions on the screen.  See also the Windows quick start guide.  It takes approximately 5-10 minutes to complete the entire setup process. The steps in the setup process are as follows:  •  Configuring your location, language and keyboard type •  Configuring your time zone •  Accepting license agreement •  Naming your computer •  Creating an account •  Completing configuration   •  Do not turn off your computer until completing Windows setup. If you turn it off, you may not be able to set up Windows later.   •  Be sure to connect your computer to AC power source. An undercharged battery may not be able to complete the Windows setup.  •  Do not connect any peripheral devices to your computer until the    Windows setup is completed. Otherwise your computer may malfunction.  •  If the display turns off, some power management may function. In this case, press any key to resume your computer from the power management. . (Refer to Power Management section of Chapter 3.) •  If you cannot operate the keyboard or the glide pad, press the power button for more than four seconds to turn off your computer. Be sure that the power indicator turns off; then, after more than 10 seconds, press the power button to turn on your computer again.  After completing the Windows XP setup: •  Confirm Time Zone is correctly selected and set the date and time by double-clicking the time appearing on the right of the taskbar to open Date and Time Properties dialog box. Press Fn+F1 (     ) keys to activate the integrated antennas for Wireless LAN communication.
1  1-5   Properties Dialog Box on Windows  In this manual, you will often see the expression “XXX Properties dialog box.” The dialog box is a window containing text boxes, check boxes, buttons, etc., with which you can send commands to Windows or other applications.  To open the properties dialog boxes, click start - Control Panel. The Control Panel has two types of views: Category View and Classic View. The Category View allows you to choose the category that may be related to what you want to do, then, choose your task by clicking it. The Classic View gives you the icons representing their components or features. Double-click one of the icons to open its dialog box or window. Some of the dialog boxes you will use often are:  •  Display  •  Phone and Modem Options •  Mouse •  Power Options •  System   Clicking Switch to XXX View string appearing at the upper left of the Control Panel window allows you to toggle between the two views.
 1-6  1 Turning Off Your Computer  When you’ve finished using your computer, turn it off with one of the following steps:  •  From the start menu  1.  Click start – Turn Off Computer. 2.  In the Turn off computer dialog box, click Turn Off.  •  With the power button  Before using this step, confirm that the power button is enabled to shut down your computer. Follow these instructions. 1. Open Power Options Properties dialog box. Select Advanced tab. 2. Confirm that Shut down is selected in the pull-down menu of When I press the power button on my computer.  Close the display cover to keep the screen and keyboard clean and protected.   If you have not saved the data, a dialog box will appear asking whether you want to save it.   •  Do not turn off or reset your computer while the hard disk indicator, optical drive indicator, or the indicator on the optional external floppy disk drive is lit. Doing so may damage or even wipe out the data. •  After turning off your computer you need to wait at least ten seconds before turning it back on. Turning the power off and on in rapid succession can damage your computer’s electrical circuitry.
 2-1  2 CHAPTER 2      Basic Operations  This chapter describes the basic operations of your computer.  Choosing Power Source  You can use your computer with one of the following power sources: •  AC power from a wall outlet Use AC power whenever possible; rely on the battery only when AC power is not available. •  Rechargeable battery  A standard battery pack is supplied with your computer. You can also use an optional add-on battery. See Chapter 3 for the battery information.   About Power Indicators The following indicators show the power status of your computer.  Indicator Light  Meaning Power On (green)  Operating Blinking (green)  In System Standby  Off  Powered off or in System Hibernate Battery   On (green)  Fully charged  On (orange)  Being charged  Connected to AC Power Source Blinking (orange) In abnormal state (Remove the battery pack and install it again.)   Off   Has power    Powered by Battery  Blinking (red)  Almost completely discharged (The warning beep sounds.)
 2-2  2 The battery indicator is always off when your computer is turned off and not connected to AC power source.   •  When the battery is hot, the battery indicator may turn off and stay off until the battery becomes cool. •  For more information on System standby/hibernate, see Chapter 3.  Using AC Adapter When connected to a wall outlet, the AC adapter provides power for operation and charges the battery pack. The AC input voltage can range from 100 to 240 volts so that you can use your computer with the appropriate plug adapter.    The AC power cord included with your computer is appropriate for the voltage used in the area in which you purchased your computer. If you attempt to connect your computer to a wall outlet in other areas, check the voltage of the outlet and use an AC power cord appropriate for the outlet. Consult local service staff if you are not sure.
 2-3  2 Resetting System  You may need to restart the system if your computer becomes inoperable or after adding new hardware or software. When the message appears after the installation, click OK, Yes, etc. to restart Windows.  You can also restart Windows by clicking start – Turn Off Computer; then, Restart.   Resetting may cause data loss. Use the resetting process only if the normal Windows XP Shut Down does not work because of software malfunction. Although resetting will not damage the system, you may lose the data you are processing.  Warm Boot (Software Reset) If the system is locked up because of a software problem, you can reset or reboot the system by pressing the Ctrl+Alt+Del keys simultaneously and select Applications tab of Windows Task Manager dialog box. Click the name of the program hanging up, then, End Task. If this does not work, select Users tab and click Disconnect or Logoff, then, Yes.  Power Switch You can turn off your computer by pressing the power button if you encounter hardware or software problems locking up the system. In this case, press the power button for more than four seconds.   Reset Switch If you cannot turn off your computer with the power button, you can use the reset switch on the bottom of your computer. To reset the system, insert a narrow object into the small hole to press the switch.   RESET Reset Switch
 2-4  2 Using Glide Pad  Your computer is equipped with an integrated pointing device called glide pad.  Using the glide pad, you can move the pointer, select an item from a menu and perform other tasks in the same way you would with a mouse.      •  Do not hit or scratch the surface of the glide pad with pointed objects (such as a ballpoint pen). •  Do not operate the glide pad with a moist finger. This may cause the glide pad to operate incorrectly.  Using Glide Pad Take a moment to become familiar with how the glide pad works.  Place Your Fingertip Place your left or right hand next to the glide pad, resting your wrist naturally in a relaxed manner. Place your thumb or a finger(s) on the glide pad.  Move Your Fingertip The rectangular surface of the glide pad acts like a miniature duplicate of the display.  As you slide your fingertip across the pad, the pointer on the screen moves in the same direction across the screen. The glide pad is very sensitive, so you do not have to exert much pressure on the pad. The glide pad will respond to a light touch from your fingertip. Glide Pad Pointer
 2-5  2 Click, Double-click, and Right-click To click or double-click, you can use the left button just like that of a mouse. Instead of clicking the left button, you can also just tap gently anywhere on the rectangular pad. For right-clicking, you must use the right button.   Drag and Drop You can move icons or windows by using “drag and drop” below:  1.  Position the pointer over the object.  2.  Press the left button; do not release it.  3.  Holding down the button, move the pointer. The object moves together with the pointer. 4.  Release the button when the object reaches its destination.  Or you can tap the pad twice instead of pressing the left button in the step 2.  Scroll You can scroll through information in a list or in a document by using the glide pad. To view information vertically, place your finger on the most right part of the glide pad and slide your finger up and down. To view horizontally, place your finger on the bottom part of the glide pad and slide your finger to the left or the right. This procedure works only in limited applications.  Changing Configuration In the Mouse Properties dialog box, you can change the configuration of the glide pad, such as swapping left and right buttons, changing the pointer size, etc. Double-click Touch Pad icon ( ) on the taskbar to open the Mouse Properties dialog box.
 2-6  2 Using Keyboard  Your computer, equipped with the Windows Enhanced Keyboard, provides all the functionality of a full-sized desktop keyboard.    Special Keys Windows Key Opens the Windows start menu.   Application Key Opens an application-specific short-cut menu. Equivalent to right-clicking.  System Function Keys When pressed together with the Fn key, function keys set specific system parameters. This combination is sometimes referred to as “hot keys”.  Fn + F1 () Turns the wireless LAN antenna on and off. (for built-in wireless LAN model only )   Fn + F5 () Rotates display mode between the LCD only, an external monitor only, and both.  (when connecting an external monitor)   Fn + F6 () Decreases the LCD screen brightness.   Fn + F7 () Increases the LCD screen brightness.   Fn + F11 () Turns on and off the LCD screen.   Fn + F12 () Forces your computer into System standby/System hibernate/Shut down. (See Power Management of Chapter 3 for more information.)   Do not use the function keys Fn+F5 during watching DVD videos or animation, or playing a video game.
 2-7  2 Using Optical Drive  Your computer is equipped with an optical drive allowing you to read from DVD and CD and write onto CD-R/RW.    CAUTION FOR LASER  Use of controls or adjustments or performance of procedures other  than those specified herein may result in hazardous radiation exposure. Maximum output and wavelength of the laser:  108mW, 784nm(CD-R/RW) 6mW, 662nm(DVD-ROM)  CLASS 1LASER PRODUCTLASER KLASSE 1   Handling Disk •  Do not write on either side of the disk, particularly the non-label side.  Data is read/written from/onto the non-label side.  Do not mark this surface. •  Keep your disks away from direct sunlight, heat and excessive moisture. •  Always hold the disks by the edges.  Fingerprints, dirt or water on the disks can cause noise or mistracking. If a disk is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius.
 2-8  2 Inserting Disk 1.  Make sure the optical drive indicator is not lit on; then, press the eject button. The drive tray will pop out.   2.  Gentry pull out the tray.  3.  Place your disk, label side up, onto the tray and slightly press the center of the disk until it is locked into the place.  Optical Drive Indicator Eject Button
 2-9  2 4.  Gently push the tray back into your computer.   •  Do not leave the tray pulled out.  Also, avoid touching the lens in the tray.  If the lens becomes dirty, the disk may malfunction. •  Do not wipe the lens with materials with rough surface (such as paper towels).  Instead, use a cotton swab to gently wipe the lens.  Removing Disk 1.  Make sure the optical drive indicator is not lit and press the eject button. The optical drive tray will pop out.   Make sure the optical drive indicator is not lit or blinking before pressing the eject button.  2.  Gently pull out the tray. 3.  Remove the disk from the tray by holding its edge.  4.  Gently push the tray back into your computer.
 2-10  2 Writing Data to CD-R/RW Disk  You can use CD-R or CD-RW discs to write data on. CD-RW is an erasable disc onto which you can write data and from which you can erase data. CD-R is non-erasable disc onto which you can write data only once. If free space remains, you can add data until the disc is full.  To write data, run the application called Drag’n Drop CD+ DVD installed on your computer. See the online help of Drag’n Drop CD+ DVD for the details. To run the application, click start – All Programs - Drag’n Drop CD+ DVD - Drag’n Drop CD+ DVD.    •  Before writing to CD-R/RW, follow the instructions below: •  Connect the AC adapter. If the battery is discharged, writing process will stop and fail. •  Disable the power management. See Power Management of  Chapter 3. •  Close all of the unnecessary or the automatic start-up applications. •  Disable the screen saver. (Refer to Changing Wallpaper and Setting Screen Saver section later in this chapter.) •  You cannot add data onto music CDs even if they are not full.
 2-11  2 Watching DVD Video  You can enjoy watching a DVD video on your computer using the application called WinDVD. See online help of WinDVD for more details. To run the application, click start – All Programs – InterVideo WinDVD4 - InterVideo WinDVD4.   •  Before watching DVD videos, follow the instructions below: •  Connect the AC adapter. If the battery is discharged, the operation will stop. •  Disable the power management. See Power Management of Chapter 3. •  Close all of the unnecessary or the automatic start-up applications.  •  Disable the screen saver. (Refer to Changing Wallpaper and Setting Screen Saver section later in this chapter.) •  When playing a DVD video, you may experience a picture with an irregular motion, or frame dropouts, depending on videos. •  Set the display mode to LCD only or external monitor only.  When set to simultaneous display, the DVD video will not be displayed properly. •  This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.  (Apparatus Claims of U.S. Patent Nos. 4,631,603; 4,577,216;, 4,819,098 and 4,907,093 licensed for limited viewing uses only.)  Make sure to remove the DVD video from the drive when you finish watching it. If you turn off your computer with the disc left in the drive, the drive may not be recognized when your computer is turned on again.  Changing Region Code   A DVD video has a region code which prevents playback of the disc in certain regions. The region code appears on the top of the disc.  When shipped from the factory, your optical drive is set to a region code applicable to your area.
 2-12  2   Your DVD drive region code can be changed. Code change is limited. Once the limit is reached, it cannot be changed any more. To confirm the limit, click Region tab of Setup dialog box and check bottom line in the window. (Refer to Using Parental Control section on the next page to open the Setup dialog box.)  Make sure to log on your computer as a member of the Computer administrators group. Otherwise you cannot change the region code. Available region codes are: Region Code  Area 1 U.S.A, Canada 2  West Europe, Japan, South Africa 3  South East Asia (including Hong Kong) 4  Australia, Spanish America  5  Former Soviet Union, Indian Subcontinent, Africa 6 China  To change the region code: 1.  Insert a DVD video into the drive. If the region code of the DVD video is different from that of your drive, Confirm Region dialog box appears. 2.  The region code currently selected is checked in the left box. Region code of your DVD video is checked in the right box. If you want to change the drive code and play the DVD video, click OK.    On some DVD videos, plural region codes are selectable in the right box of Confirm Region dialog box. Carefully choose an appropriate one.  When Confirm Region dialog box does not appear: 1. Click start  - My Computer – View system information. 2. In System Properties dialog box, select Hardware tab and click Device Manager button. 3. In Device Manager dialog box, double-click DVD/CD-ROM drives string and MATSHITA xxxxxx.(xxxxxx is your optical drive name.) 4. Select DVD Region tab, choose the listed distribution area of the DVD video, then, confirm the region code shown in the New Region field is correct and click OK. 5.  Read the message on the screen, then, click OK.
 2-13  2 Using Parental Control If you want to set the parental control to prevent your children from watching an inappropriate movie, follow the steps below: 1. Run the InterVideo WinDVD4. 2.  Right-click somewhere in the InterVideo WinDVD4 window and click Setup…. Setup dialog box will appear. 3. In Preferences tab, click Set Password button in Parental Playback Control section.  4.  Type your password. See online help of WinDVD for more details.  Displaying Video on TV Set You can connect a television set with S-Video input to your computer and enjoy DVD video on a big display.   •  Before connecting the television set, disconnect the external monitor. •  Connect the television set to your computer directly. Otherwise, the screen may be distorted.  Connecting TV Set 1.  Turn off your computer and the television set. 2.  Connect the television set to your computer.      3.  Turn on the television set, then, your computer. Audio Output Jack Stereo Mini Plug S-VideoOutput Jack To S-Video Input Jack To Audio Input Jacks:    White Plug to Left    Red Plug to Right
 2-14  2 4. Click start – Control Panel – Appearance and Themes in Category view. 5. Click Change the screen resolution string. 6. Set the Screen resolution to 800 by 600 pixels and set the Color quality back to Medium (16 bit).     Make sure to set the Screen resolution to 800 by 600 pixels and the Color quality to Medium (16 bit) when you display the image on TV. Otherwise, the image cannot be displayed properly.  7. Click Advanced button and select S3Display tab. 8.  Check the box of TV and click OK twice.  9.  If you can see the screen image on the television set, click Yes. 10. Click OK and close the Display Properties dialog box.    Disconnecting TV Set 1.  Turn off your computer and the television set. 2.  Disconnect the television set from your computer.   •  Before disconnecting the television set, be sure to turn off your computer and the television set. •  After disconnecting the television set, set back the display property. (Refer to Adjusting Display later in this chapter.)  Enjoying Dolby Digital Audio Your computer is Dolby Digital compliant.  With Dolby Digital compliant audio equipment or headphones, you will have an audio output similar to a big theater.  Follow the steps below. (Refer to Audio System of Chapter 4 for connection.) 1. In Setup dialog box, click Audio tab. (Refer to the steps in Using Parental Control section to open the Setup dialog box.) 2. Select Digital (S/PDIF) out to External Processor, then, click OK.   WinDVD allows you to enjoy virtual surround sound through your speakers or headphones. To enable this function, follow the steps on the next page. When you listen to the movie through speakers: 1.  Connect your speakers to your computer and click the subpanel
 2-15  2 button ( ) and Audio Mode.  2. Select Speakers from the Listen on pull-down menu. 3. Click OFF button to enable this function. It turns ON. When you use headphones: 1.  Connect your headphones to your computer and click the subpanel button ( ) and Audio Mode. 2.  Select Headphones from the Listen on pull-down menu. 3.  Click OFF button to enable this function. It turns ON.  Refer to the online help of WinDVD for more information.   Controlling Volume  You can adjust the output volume of your computer with one of the following volume controls that interact with each other.  With Volume Control Turn the volume control on the left side of your computer backward you to increase the volume. Turn it toward you to decrease the volume.    On Windows Increases the volume Decreases the volume Subpanel Button
 2-16  2 1. Click start – Control Panel. 2. Click Sounds, Speech, and Audio Devices; then, Sounds and Audio Devices. If Classic view is selected, double-click Sounds and Audio Devices icon.  3. In Sounds and Audio Devices Properties dialog box, slide the lever to adjust the output volume.  4. Click OK and close the dialog box, then the Control Panel window.   You can also easily adjust the volume in the window that will open when clicking the speaker symbol on the taskbar. When the symbol is not on the taskbar, check the box of Place volume icon in the taskbar in the step 3.  If you want to control the output volume of each source individually: 1. Click start – Control Panel. 2. Click Sounds, Speech, and Audio Devices, then, Sounds and Audio Devices. If Classic view is selected, double-click Sounds and Audio Devices icon. 3. In Sounds and Audio Devices Properties dialog box, click Advanced of Device volume field. 4.  Slide the lever of the source that you want to adjust. 5.  Close the dialog box, then; click OK and close the Control Panel window. If you control: Wave    Controlling the volume of CD/DVD or WAVE file SW Synth    Controlling the volume of MIDI file  Adjusting Display   You can adjust the brightness, resolution, and number of colors of the internal LCD display for more comfortable viewing.   Changing Brightness of Display Press and hold Fn key and then press F6 ( ) key to decrease the brightness of the internal LCD display. Press and hold Fn key and then press F7 (  key to increase the brightness of the internal LCD display.
 2-17  2 Changing Resolution and Number of Colors When shipped, your computer is set to the default resolution and color. The default resolution is 1024 x 768 at 64K colors. To change the resolution and the number of colors, follow the instructions below: 1.  Right-click anywhere on the Windows desktop except icons or folders. 2. Select Properties from the pop-up menu. 3. In the Display Properties dialog box, select Settings tab. 4.  Select the number of the colors in the Color quality, and select the resolution in Screen resolution.  Refer to the table below for possible resolutions and colors. 5. Click OK; then, Yes.   Available Resolutions and Colors   Resolution Number of Colors 800 x 600  64K, 16M(*2) 1024 x 768  64K, 16M(*2) 1280 x 1024(*1) 64K, 16M 1600 x 1200(*1) 64K, 16M   (*1) Can be chosen for an external monitor only when it is capable of the listed        resolution modes. Cannot be set when displaying on the LCD monitor only or        on both of the LCD and the external monitor simultaneously.   (*2) On the internal LCD screen, the number of colors in this mode is made using                  a dithering algorithm.    •  You cannot switch to a display resolution and number of colors that are not available.  •  In the Color Quality, Medium (16 bit) means 65,536 (64K) colors and Highest (32 bit) means about 16,770,000 (16M) colors. •  If you select Highest; •  Drawing speed may be delayed. •  When playing animation, the screen may be distorted.
 2-18  2 Changing Wallpaper and Setting Screen Saver You can enjoy various desktop patterns or screen savers. Changing Wallpaper 1. In the Display Properties dialog box, select Desktop tab. 2. Select appropriate wallpaper listed in Background field.  3. Click OK. Setting Screen Saver  1. In the Display Properties dialog box, select Screen Saver tab.  2.  Select an appropriate screen saver from the pull-down menu in Screen saver field and set time when screen saver starts. 3. Click OK.   To disable the screen saver, select [None] from the Screen saver pull-down menu.
 2-19  2 Sharing Your Computer   If you are sharing your computer with your colleagues or family members, set a user account for each person. Every user can choose his/her favorite desktop setting, web site lists, or make his/her own My Documents folder etc., and save them to his/her user account. When you turn on your computer, select your user account.    Set New User Account  1. Click start – Control Panel. 2. Click User Accounts. If Classic view is selected, double-click User Accounts icon. 3. Click Create a new account string. 4.  Type a name for the new account and click Next. 5.  Select the account type; then, click Create Account. If you have selected a Limited account, then that user account has limits for using your computer. See Help and Support Center in start menu for more details. 6. Close the User Accounts dialog box; then, the Control Panel window. If more than one user accounts are set to your computer, you must select which user account you will log in when you turn on your computer.  Log off Your Computer  “Log off” is useful because you do not have to turn off your computer when you finish your task and pass your computer to another person. There are two ways to log off your computer, Switch User and Log Off. If you select Switch User, you can pass your computer to another person without closing your current applications. For example, if you are viewing a Web site, and your colleague needs to open a program on your computer, use Switch User. You can then view the same Web site by just switching users after your colleague finishes with your computer. If you select Log Off, the system will close all your session and you need to save your files before logging off your computer. 1. Click start – Log Off.   2. Select Switch User or Log Off. If you select Log Off, the dialog box that asks you to save your data may appear. 3.  Select another account to start Windows again.
 2-20  2   If you cannot see Switch User in Log Off Windows dialog box, click Change the way users log on or off string in User Accounts dialog box, and check Use Fast User Switching and click Apply Options.    Set Password to User Account You can set a password to each user account to avoid unauthorized use of your computer. Once you set the password, you need to enter it when you log on to its account.  If the entered password is not correct, you cannot start your computer with that user account, so unnecessary password setting can cause trouble in starting the system.  Setting Password 1. Click start – Control Panel. 2. Click User Accounts. If Classic view is selected, double-click User Accounts icon. 3.  Select the account you want to set a password to. You will only have this option if you log onto your computer as a member of the Computer administrators group.  If you log on your computer with a limited user account, go to the next step. (You cannot set a password to another user account.) 4. Select Create a password string.   •  If the password has been already set, Create a password will not appear. •  Only the members of the Computer administrators group can set a password to another user account.  5.  Type a new password. 6.  Type the new password again to confirm it. 7.  If necessary, type a password hints word to remember the password you set. 8. Click Create Password. 9.  If you are asked whether you want to make your files and folders private, click Yes, Make Private or No. If not, go to the next step. 10. Close the User Accounts dialog box; then, the Control Panel window.
 2-21  2 Changing Password 1.  Follow the steps 1-2 on Setting Password section. 2.  Select the account you want to change, if you log on to your computer as a member of the Computer administrators group.  If you log on your computer with a limited account, go to the next step. (You cannot change the password of another user account.) 3. Select Change the password string or Change my password string.   •  If the password has not been set yet, Change the password or Change my password will not appear. •  Only the members of the Computer administrators group can change the password of another user account.  4.  Type the current password. If you are changing another user’s password, skip this step. 5.  Type a new password. 6.  Type the new password again to confirm it. 7.  If necessary, type a password hints word to remember the password you set. 8. Click Change Password. 9.  If  you are asked whether you want to make your files and folders private, click Yes,  10. Close the User Accounts dialog box; then, the Control Panel window.  Deleting Password 1.  Follow the steps 1-2 on Setting Password section. 2.  Select the account you want to delete its password, if you log on to your computer as the members of the Computer administrators group.  If you log on your computer with a limited account, go to the next step. (You cannot delete the password of another user account.) 3. Select Remove the password string or Remove my password string.   •  If the password has not been set yet, Remove the password or Remove my password will not appear. •  Only a member of the Computer administrators group can delete the password of another user account.
 2-22  2 4.  Type your password and click Remove Password. If you log on to your computer as a member of the Computer administrators group and want to delete the password of another user account, just click Remove Password. 5. Close the User Accounts dialog box; then, the Control Panel window.
 3-1  3 CHAPTER 3      Battery and Power Management  This chapter explains how to manage your computer’s power effectively and use the battery pack.   In this section, you often see the expression “Power Options Properties dialog box”. To open the dialog box: 1. Click start – Control Panel.        2. Click Performance and Maintenance – Power Options in Category view or double-click Power Options icon in Classic view.   Battery Pack  When not connected to an external power source, your computer operates with the rechargeable battery pack. The duration of the battery life may be longer if your computer’s power management is active. See the next section for power management.  To keep the battery life long:  •  Condition the battery pack if the actual remaining power in your battery is less than what Windows Power Meter indicates. (See Conditioning Battery Pack section in this chapter.) •  Turn off your computer when you are not using it.  •  The duration of the battery will depend on your computer usage. Using applications, which heavily use the optical drive or external peripherals, will result in shorter battery life. •  When using your computer for several hours with battery packs, enable power management and set System hibernate. Refer to the Power Management section in this chapter. •  When the battery has not been charged, your computer may not operate properly. Connect your computer to the AC power source for the battery changing.
 3-2  3 Charging Battery Pack 1.  Connect the AC adapter to your computer. While the battery is being charged, the battery indicator lights orange. 2.  When the battery is fully charged, the battery indicator turns green. Charging time may vary according to the status of your computer.    •  The battery indicator may turn off even while the battery pack is being charged. This is because the battery pack is hot, and the charging stops temporarily. When the battery becomes cool, the charging will start and the battery indicator will turn on again. •  The battery pack may not be installed correctly if the battery indicator blinks orange. In this case, turn off your computer, remove the AC adapter and the battery pack; then, install the battery pack and connect the AC adapter again. If the battery indicator still blinks orange, ask your local dealer for assistance. •  When the battery pack is hot (for example, after a long usage), it may take longer to be fully charged.  Checking Battery Level You can check the battery level by placing the pointer on the battery icon (    : powered on battery) or AC plug icon (      : powered on AC power and charging the  battery pack) on the taskbar, or double-clicking one of these icons (     ,       or      : powered on AC power) to open the Power Meter dialog box. If the battery is fully charged, remaining capacity level will not appear even if you point to the icon. If you cannot see the battery or AC plug icon, follow these instructions:  1. In the Power Options Properties dialog box, select Advanced tab. 2. Check Always show icon on the taskbar and click OK. 3. Close the Control Panel window.   •  The remaining operating time depends on the power you are consuming.  If you are using the audio system, PC card slot, hard disk drive, media cards, peripherals or optical drive, your computer may consume more battery life. •  If the actual remaining power in your battery is less than what Power Meter indicates, you should condition the battery pack as per the procedure on Conditioning Battery Pack section in this chapter.
 3-3  3 Low Battery Indication When the battery power becomes significantly low, the battery indicator () blinks red and the warning beep sounds. Save your data and turn off your computer, or connect your computer to AC power source immediately. Otherwise, your computer will be shut down and the unsaved data may be lost.    On Windows, a beep sound or an on-screen message will tell you when the battery drops to the specified level and your computer will go on System standby/System hibernate or shut down automatically.  To set Windows battery alarm:  1. In the Power Options Properties dialog box, select Alarms tab. 2.  Set the battery level at which the alarms are activated. We recommend you set Critical battery alarm to 5 % or more and Low battery alarm to more than the value of Critical battery alarm. 3. Set the Alarm Action… to the appropriate settings. 4. Click OK twice.  5. Close the Control Panel window.   Battery Indicator
 3-4  3 Conditioning Battery Pack When the actual remaining power in your battery is less than what Windows Power Meter indicates, you need to condition the battery pack or buy a new one. 1.  Make sure your computer is powered off. Connect your computer to AC power and fully charge the battery. The battery indicator turns orange first; then, green when the battery pack is fully charged.   When the battery is fully charged, the battery indicator turns green.   2.  Turn on your computer. 3.  When the message Press <F2> to enter SETUP appears, press F2 to open the Setup Utility.  4.  Disconnect the AC adapter, and leave your computer on until the battery is completely discharged and the system shuts down automatically. 5.  Connect your computer to AC power and let the battery fully charged again.    •  Do not turn on your computer while charging the battery pack. •  Do not connect your computer to a wall outlet while discharging the battery. The conditioning will be cancelled.  Repeated charging and discharging or long-term storage of the battery pack cause battery deterioration. In this case, replace the battery pack with a new one.  Changing Battery Pack When repeatedly charged and discharged the battery pack or stored for a long term, it will deteriorate (the deterioration rate depends on the operating environment).  The battery deterioration will result in declining its capacity and power. If the battery life becomes extremely short even after the conditioning, you should buy a new battery pack. Ask your local dealer for a new battery pack.  When you replace the battery pack with a new one: 1.  Turn off your computer and disconnect the AC adapter from your computer. 2.  Close the display cover and turn your computer over on a stable surface.
 3-5  3 3.  Unlock the battery stopper of your computer to the left and hold it; then, unlock the battery release lever of the battery pack to the left and hold it; then, pull out the battery pack.     4.  Insert a new battery pack into your computer by matching the projected parts of the battery with the notched parts on your computer.  5.  Press down the battery pack until you hear the clicking sound.  6.  Turn your computer over. Battery Stopper Notched Part Battery Release Lever Projected Part
 3-6  3 Optional Add-on Battery Pack  The optional add-on battery pack (CE-BL30) allows you to operate your computer for extended period.     Never attach any add-on batteries but the optional ones (CE-BL30).  Attaching Add-on Battery Pack Follow the steps below:  1.  Turn off your computer and disconnect the AC adapter from your computer. 2.  Close the display cover and turn over your computer on a flat place. 3.  Open the cover of the add-on battery pack socket on the bottom of your computer.    Cover
 3-7  3 4.  Hook the projected parts of the battery pack up to the notched parts of your computer.  5.  Softly press down the battery pack.  6.  Slightly press the two levers of the battery pack inwards and hold them; then, press down the battery pack and release the levers.   Make sure the triangle logos on the battery pack go with the line marks of your computer.  Notched Part Projected Part Levers Triangle Logo Line Mark
 3-8  3 Removing Add-on Battery Pack Follow the steps below: 1.  Turn off your computer and disconnect the AC adapter from your computer. 2.  Close the display cover and turn over your computer on a stable surface. 3.  Slightly press the two levers of the battery pack inwards and hold them.  4.  Slightly lift up the front of the battery pack and release the levers.   Make sure to lift up the battery pack softly and slightly. Lifting it up with excessive force may damage the projections of the battery. 5.  Push out the battery backward and remove it.   Levers
 3-9  3 6.  Close the cover on the bottom of your computer.    Be sure to close the cover when the add-on battery pack is not attached. Otherwise some objects may damage inside your computer.   Checking Battery Level of Add-on Battery  You can check the add-on battery level with one of the following ways.  On Windows Refer to Checking Battery Level section in this chapter.  With battery level lamp When you press the battery level button, the battery level lamps light up.    Conditioning Add-on Battery Pack  1.  Connect the add-on battery pack. 2. Refer to Conditioning Battery Pack in this chapter.  Cover Battery Level Button Battery Level Lamps
 3-10  3 Power Management  Power management saves electricity and extends battery life by controlling power supply to built-in devices. You can set the following power management properties on Windows.  •  Stopping power supply to the hard disk •  Stopping power supply to the display •  Controlling CPU speed  •  Using System standby/hibernate To open Power Options Properties dialog box, click start – Control Panel, and click Performance and Maintenance; then, Power Options.  If Classic view is selected, double-click Power Options icon.   Note that the power management may not seem to function when you are using an application program that accesses the hard disk periodically.    Stopping Power Supply to Hard Disk 1. In Power Options Properties dialog box, select Power Schemes tab. 2. Set Turn off hard disks to an appropriate value, and click OK. 3. Close the Control Panel window.  Stopping Power Supply to Display   This procedure is also effective for an attached external monitor complying with power management.   1. In Power Options dialog box, select Power Schemes tab. 2. Set Turn off monitor to an appropriate value, and click OK. 3. Close the Control Panel window.
 3-11  3 Controlling CPU Speed  Windows XP controls the processor performance to reduce power consumption.   Do not control the processor performance, or connect/disconnect the AC adapter while communicating, or reading/writing data. Otherwise your computer may malfunction.  1. In the Power Options Properties dialog box, select Power Schemes tab. 2.  Select an appropriate power scheme from the pull-down menu in Power schemes field according to the table below, and click OK. 3. Close the Power Options Properties dialog box, then the Control Panel window.  Power Scheme  Processor Performance Using AC Power Always runs at highest performance state Home/Office Desk Using Battery  Performance state will be chosen based on CPU demand Using AC Power Performance state will be chosen based on CPU demand Portable/Laptop Using Battery  Performance state will be chosen based on CPU demand Using AC Power Performance state will be chosen based on CPU demand Presentation Using Battery  Always runs at the lowest performance state Using AC Power Always runs at highest performance state Always On Using Battery  Always runs at highest performance state Using AC Power Performance state will be chosen based on CPU demand Minimal Power Management Using Battery  Performance state will be chosen based on CPU demand Using AC Power Performance state will be chosen based on CPU demand Max Battery Using Battery  Always runs at the lowest performance state
 3-12  3  •  Note that Power schemes includes other power management settings (such as a timer for System standby, etc.) appearing on Power Schemes tab. Confirm those settings are set to an appropriate value when you select the processor performance using power schemes facility. •  You can set your own Power scheme. Set all power management settings to your suitable ones, and click Save as…; then, type an appropriate name and click OK. •  Once the preinstalled Power scheme settings listed on the previous page are deleted, there is no way but re-installation to resume them.  Using System Standby/Hibernate System standby/hibernate is a very useful power management tool. For example, you can restart your computer from stand by mode more quickly than shut down mode. When your computer resumes from System standby/hibernate, the system restores the exact last state of your computer. On Windows, you can set the conditions under which the system enters System standby or System hibernate.   •  System standby stores the current condition of your computer in RAM and stops power supply to all but a few essential components. Your system enters and resumes from System standby per the conditions mentioned later. In System standby, the power indicator blinks green. To resume from System standby, operate your computer again. •  System hibernate saves the current condition of your computer in part of the hard disk and turns off your computer. Your system enters and resumes from System hibernate per the conditions mentioned later. In System hibernate, the power indicator turns off. To resume from a System hibernate, press the power button.   When entering/resuming from System standby/System hibernate, follow the instructions below: •  Finish communications, printing, and playing music or video before entering System standby/System hibernate.  •  Do not operate your computer or peripheral devices, or connect/disconnect peripheral devices, while entering/resuming from System standby/System hibernate. •  While operating on battery power that does not have enough power, your computer may not resume from System standby/hibernate. In this case, connect the AC adapter to your computer. •  Save the data before your computer enters System standby. If the power supply to your computer is stopped, the RAM contents will be lost. •  Select your user account if Windows requires when your computer has resumed from System standby/hibernate.
 3-13  3 Supporting System Hibernate    If your battery becomes completely discharged during System standby, you will lose unsaved data and will need to reboot your computer. Therefore, if you are planning to leave your computer powered by battery for long periods of time, we recommend System hibernate.  Confirm that System hibernate is supported with the following steps. 1. In the Power Options Properties dialog box, select Hibernate tab. 2. Confirm Enable hibernation is checked in Hibernate field. 3. Click OK, then, close the Control Panel window.  Set Timer to Enter System Standby/Hibernate Automatically Your computer will enter System standby/hibernate automatically when the specified time has passed without any operation. To set the time: 1. In the Power Options Properties dialog box, select Power Schemes tab. 2.  From the pull-down menus in System standby or/and System hibernate, select the elapsed time before your computer automatically enters System standby/hibernate. 3. Click OK, then, close the Control Panel window.  Entering System Standby/Hibernate  Your computer enters System standby/hibernate in each of the following cases: •  You select Stand By or Hibernate (which replaces Stand By when you press Shift key) in Turn off computer dialog box. To open the dialog box, click start – Turn Off Computer. •  The specified time in System standby or System hibernate in Power Schemes tab of Power Options Properties dialog box has passed without any operation (See the previous section). •  The screen cover is closed. The above functions if you perform the following: 1. In the Power Options Properties dialog box, select Advanced tab.  2. Select Stand by or Hibernate in When I close the lid of my portable computer.  3. Click OK , then, close the Control Panel window.
 3-14  3   •  You press the power button. The above functions if you perform the following: 1. In the Power Options Properties dialog box, select Advanced tab.  2. Select Hibernate or Stand by in When I press the power button on my computer.  3. Click OK , then, close the Control Panel window.  •  You press Fn + F12 (   ) . The above functions if you perform the following: 1. In the Power Options Properties dialog box, select Advanced tab.  2. Select Hibernate or Stand by in When I press the sleep button on my computer.  3. Click OK, then, close the Control Panel window.   If Ask me what to do is selected in the step 2 of You press the power button or You press Fn+F12 (    ) , the Turn off computer dialog box will appear when you press the power button or Fn+F12 (     ) key combination. You can select System standby or System hibernate at that timing.  •  The battery level is low. The above functions if you set the alarm in Windows. See Low Battery Indication earlier in this chapter.  Disabling Power Management 1. In the Power Options Properties dialog box, select Power Schemes tab. 2. Set Turn off monitor, Turn off hard disks, System stand by, and System hibernate to Never, and click OK.    3. Close the Control Panel window.
 4-1  4 CHAPTER 4      Peripherals  This chapter describes how to use peripheral devices with your computer. You can connect a floppy disk drive unit, a printer, an external monitor, an IEEE1394 device, or other devices to your computer. To ensure proper use, be sure to read the instructions for each peripheral device before connecting it to your computer.   Using Peripherals   You can use the peripheral devices shown on the next page. For the details, refer to the section explaining each device, or contact your dealer.    •  Be sure to turn off your computer and the peripheral devices before connecting them (except when connecting/inserting USB devices, an IEEE1394 device, a PC card, etc.).  •  Confirm the peripheral device you will connect is Windows XP compatible. •  When you connect some of the devices, you may have to turn on your computer before powering on the devices.  •  Some devices require that you install their drivers before use. (You may need to connect an optional external floppy disk drive unit to install the drivers.)
 4-2  4 Peripheral Connection Overview           Video Equipment with S video  USB Devices Headphone / Audio Equipment Microphone External Monitor  IEEE1394 Device PC Card
 4-3  4 Optional External Floppy Disk Drive Unit  You can use double-density (2DD) 720KB or high-density (2HD) 1.44MB floppy disks with the provided external floppy disk drive unit (CE-FD05).  Connecting Optional External Floppy Disk Drive Unit   •  Do not place the floppy disk drive unit on its side or upside down. •  Do not press on the floppy disk drive unit. It may damage the drive or cause malfunction. •  Do not place the AC adapter on the floppy disk drive unit. It may cause the drive to malfunction.  Connect the floppy disk drive unit cable to either of the USB ports on your computer. Be sure to let the USB mark side up when connecting the cable to your computer.     Handling Floppy Disk •  Do not open the shutter and touch the disk inside; otherwise, you will not be able to read or write data from/to the disk. •  Do not place floppy disks near magnets or heat source, in direct sunlight or in a dusty place, etc. •  Never subject a disk to sudden shocks or extreme vibration. Do not drop, bend, or place heavy objects on a disk. •  Do not spill liquid onto a disk. USB Mark USB Port
 4-4  4  Inserting a Floppy Disk Hold the floppy disk with the arrow facing up and towards the drive. Slide the disk into the drive until it is locked into place.     •  Always insert a floppy disk straight into the floppy disk drive. •  When inserting the disk, make sure it is not upside down. •  Do not use excessive force when inserting the floppy disk. If you have difficulty inserting or removing disks, seek the assistance of an authorized service technician. •  Do not touch the disk while reading/writing data. It may cause malfunction of your computer and the drive.  Ejecting Floppy Disk   Before ejecting the floppy disk, make sure the indicator of the floppy disk drive unit is not lit.  Press the eject button firmly. The disk will pop out slightly. Remove it and store it properly.  Indicator Arrow Facing Up Eject Button
 4-5  4 Formatting Floppy Disk 1.  Make sure the floppy disk is not write-protected, and insert it into the floppy disk drive. 2. Click start – My Computer. 3. Right-click 3 ½ Floppy (A:) icon; then, click Format… from the pop-up menu. 4.  Select the appropriate formatting options.  5. Click Start to start formatting.    •  When you format a floppy disk, all data previously stored on the disk is lost. •  You cannot format a double-density (2DD) 720KB floppy.   Removing External Floppy Disk Drive Unit To remove the unit, you need to perform the following steps before you remove it:  1. Click Safely Remove Hardware icon ( ) on the taskbar. If you cannot find the icon, click   to show all kinds of icons. 2. Click on Safely Remove Mitsumi USB Floppy – Drive (A:) string. Safe To Remove Hardware dialog appears. 3.  Remove the unit from your computer.  External Display  You can use an external monitor with your computer. To display the same images on both displays simultaneously, use the 1024x768 resolution.    •  Some monitors, which are not compatible with your computer, may not display properly. •  In this section, you often see the expression “Display Properties dialog box.” To open the dialog box, right-click somewhere on the Windows desktop and select Properties from the pop-up menu. •  To display the image on an external monitor, you may need to install its driver. Before using the external monitor, refer to the manual included with it.
 4-6  4 Connecting External Monitor 1.  Turn off your computer and the external monitor. 2.  Open the cover on the rear side of your computer.   3.  Connect one end of your external monitor cable to the external monitor port of the rear side of your computer and the other end to your external monitor.     Make sure to tighten the screws of the cable if it has.  4.  Turn on the external monitor; then, your computer.  Disconnecting External Monitor 1.  Turn off your computer and the external monitor. 2.  Loosen the screws of the monitor cable if it has, and remove the cable from your computer and the monitor.  Displaying on External Monitor To display the image on an external monitor, you may need to install the driver for the external monitor. Before using the external monitor, refer to the manual included with it.   External Monitor Port External Monitor Cable Cover
 4-7  4 Switching Display 1. In the Display Properties dialog box, select Settings tab; then, click Advanced.  2. Select S3Display. 3.  Select the output display and click OK twice.  4. Click Yes, then, OK. Close the Control Panel window.   •  You can also switch the display with Fn+F5 (). •  While playing video or animation, you may not be able to switch the display. •  The external display should be capable of 1024x768 resolution or more when displaying simultaneously. Otherwise, it cannot display properly.   Audio System  You can output sound to speakers, audio equipment or a headphone and also input sound through a microphone.  Connecting Speakers You can connect stereo speakers with an amplifier to the audio output jack on your computer.   Audio Output Jack Speakers with an Amplifier Stereo Mini Plug
 4-8  4 Connecting Digital Audio Equipment The audio output jack of your computer is compliant to S/PDIF (Sony/Philips Digital Interface). You can connect S/PDIF compliant audio equipment to your computer and output/record sound.   When recording sound with an audio equipment: •  Use AC adapter for your computer and the digital audio equipment. •  Exit other application programs. •  Disable Windows power management. •  Do not enter System standby/ hibernate. •  Do not operate your computer. •  Use the digital audio equipment compliantwith sampling rate of 48kHz. •  Sound may not be recorded correctly if you use the synchronized recording system of the digital audio equipment.  S/PDIF Compliant Audio Equipment Audio Output Jack S/PDIF Compliant Optical Audio Cable
 4-9  4 Connecting Analog Audio Equipment      You can adjust the output volume on Windows by sliding the volume lever appearing when clicking the speaker icon on the taskbar.  Connecting Headphone Use the headphone with an impedance of 8Ω or more. (32Ω is recommended).    Audio Output Jack White (L)  Red (R) Audio Output Jack Analog Audio Cable Stereo Mini Plug Stereo Mini Plug
 4-10  4 Connecting Microphone You can input sound using an external microphone connected to the microphone jack. Use an electret condenser microphone with an impedance of 2.2kΩ and an allowable voltage of 2V.    To record sound: 1. Click start; then, point All Programs  – Accessories – Entertainment. 2. Click Sound Recorder. 3. See Help for Sound Recorder for more information.  Microphone Jack Mini Plug
 4-11  4 USB Device  Your computer has an interface called Universal Serial Bus (USB) and its two USB ports support USB 1.1 and USB 2.0. With a USB connection, you can connect/ disconnect peripherals to/from the ports without turning off your computer.  Generally, when a device is connected to your computer, the necessary driver will be installed automatically. See also the manuals of peripheral devices supporting USB.    When a new device is correctly connected to your computer, the appropriate driver is automatically installed. If the driver is not installed correctly, a message will appear in the lower right of the screen. In this case, install the driver by following the instructions on the screen.       To remove USB devices, you may need to perform the following instructions before you remove them: 1. Click Safely Remove Hardware icon ( ) on the taskbar. If you cannot find the icon, click   to show all kinds of icons. If the icon does not appear, go to      Step 3. 2. Click on Safely remove xxxxx string (xxxxx is the name of your USB device). Safe To Remove Hardware dialog appears. 3.  Remove the device from your computer.  USB Ports
 4-12  4 PC Card   Your computer is equipped with a PC card  slot, which can accommodate a Type II card or a CardBus compliant card.  You can insert/eject a PC card without turning off your computer.   Inserting PC Card   When you insert a protruding PC card such as wireless networking card: •  Do not give force to the card. •  Do not store or carry your computer with the card inserted.   When a new card is correctly inserted, the appropriate driver is automatically installed. If not installed correctly, a message will appear on the lower right of the screen. In this case, install the PC card driver by following the instructions on the screen.   1.  Confirm the PC card eject button is inside your computer cabinet. If not, push it back into the cabinet.    Eject Button
 4-13  4 2.  Insert a PC card into the slot with the label face up until it is locked into place.   If the dialog box asking you What do you want Windows to do? appears, select the task you want.    Ejecting PC Card    •  Some PC cards may become hot after long use. •  Be sure to follow these instructions when ejecting a PC card. Otherwise, the system may not work properly. 1. Click the Safely Remove Hardware icon ( ) on the taskbar. If you cannot find the icon, click   to show all kinds of icons.  2. Click on Safely remove xxxxx string (xxxx is the name of your PC card.); then, Safe To Remove Hardware dialog appears.  3.  Push the PC card eject button so that it will pop out from the side of your computer.  Label Facing Up
 4-14  4 4.  Push the eject button until the inserted PC card pops out, then, remove the card.  5.  Confirm the eject button inside the cabinet. If not, push it back for safekeeping.   Printer   You can connect a USB printer to either of the USB ports.   •  Before using a USB printer, read the printer manual and install the printer driver.  •  Note that some printers may not use Found New Hardware Wizard to install the printer driver. •  You can connect the USB printer to your computer without turning off your computer.    USB Port USB Cable
 4-15  4 IEEE1394 Device     You can connect the IEEE1394 devices to the IEEE1394 port on the rear side of your computer. The IEEE1394 is digital interface for handling digital video, digital audio and other data in two directions between devices, and for controlling other equipment.    When two or more IEEE1394 compatible devices are connected to your computer in a daisy chain, operations and data transactions are possible with not only the equipment that is directly connected, but also with other devices via the directly connected device.   •  Confirm the IEEE1394 device you will connect is Windows XP compatible. •  Use AC power for your computer and the IEEE1394 device especially when reading/writing the data. •  Some IEEE1394 devices require that you install drivers before use.  Connecting IEEE1394 Device   •  You need not turn off your computer before connecting the device. •  Be sure to read the manuals of the IEEE1394 device before connecting it to your computer.   1.  Connect one end of the DV cable with the IEEE1394 connector of your computer.    IEEE 1394 Connector
 4-16  4  2.  Connect the other end of the DV cable with the DV connector of the IEEE1394 device.   3.  Install the driver according to the instructions on the screen. Generally when you connect the device to your computer, the necessary driver will be installed automatically. 4.  Start the appropriate application for handling your data.  Disconnecting IEEE1394 Device 1. Click the Safely Remove Hardware icon ( ) on the taskbar. If you cannot find the icon, click   to show all kinds of icon. If the icon does not appear, go to Step 3. 2.  If the name of your device appears, click on Safely remove xxxxx string. (xxxxx is the name of your IEEE1394 device.); then, Safe To Remove Hardware dialog appears. If your IEEE1394 device name does not appear, skip this step. 3.  Remove the DV cable from your computer.           IEEE1394 Connector (4 pin) To IEEE1394 Compliant Device  DV Cable
 5-1 5 CHAPTER 5     Communication Functions  This chapter explains how to use the built-in modem and the LAN unit.    •  When you use communications software: •  Connect your computer to the AC power source. •  Disable power management. (Refer to Disabling Power Management section of Chapter 3.) •  See also the manual or online help of the software you are using. •  The communication speed may vary depending on the traffic, local telecommunications infrastructure, and ISP (Internet Service Provider) infrastructure.  Built-in Modem   You can use the built-in modem for data transfer and fax communication.    •  The built-in modem on your computer is designed only for regular analog telephone lines. The modem may be damaged when connected to a digital ISDN terminal or a digital PBX. •  Use TA (terminal adapter) to connect the built-in modem to a digital telephone line. •  If an unusual device is attached to the line you are connecting to, the modem may not function properly. Remove the device or contact the dealer of the device. •  Before connecting to a PBX, consult the PBX maintenance staff or its service company. If the electric characteristics of your PBX are different from those of a regular analog line, the modem will not function properly. If you connect the modem to a digital PBX, both the modem and the PBX may be damaged.   •  Within the communications software you are using, set the COM port of the built-in modem to COM 3 if required. •  Before commencing with fax communication, it is recommended that you exit other application programs.
 5-2 5 Connecting Modem to Telephone Line 1.  Turn off your computer.  2.  Open the cover of the modem jack on the left side of your computer.                                     To avoid damaging the modem, close the modem cover after you finish using the built-in modem.   3.  Connect one end of the included modem cable to the modem jack and the other to the telephone line.    Be sure not to insert the modem cable into the LAN jack. It may damage the LAN jack and the modem cable.                 4.  Turn on your computer.    Connect the modem to the telephone line directly. Do not use a distributor or allotter.    Modem Jack To Telephone Line Modem Cover
 5-3 5 Configuring Modem You may have already configured your modem during Windows setup process. Otherwise, make the necessary adjustments as shown below.  Modem Configuration When you use the modem first time, you must type your location’s information. 1. Click start – Control Panel – Printers and Other Hardware; then, Phone and Modem Options. If Classic view is selected, double-click Phone and Modem Options icon. 2. In Location Information dialog box, select your country, type your area code, etc. and select your dial type; then, click OK.  After the configuration, click or double-click Phone and Modem Options (icon) to open Phone and Modem Options dialog box and double-click the location name in Locations field of Dialing Rules tab for the information you set above. Clicking Edit… or New….allows you to make a new location or change the settings.   Internet Connection Windows XP has a special Internet connection wizard to help you to connect to the Internet with ease.   1. Click start – Control Panel - Network and Internet Connections; then, Network Connections. If Classic view is selected, double-click Network Connections icon.  2. In Network Connections dialog box, click Create a new connection of Network Tasks section. The New Connection Wizard dialog box appears. 3.  Follow the instructions on the screen.   If you plan to connect into the Internet and dial an Internet Service Provider (ISP) through the modem, have your account information and dial-up number ready before you begin the wizard. Once you set your connection, you can see or edit the connection status by double-clicking the icon appearing on Dial-up of Network Connections dialog box.
 5-4 5 LAN Unit  You can connect to a LAN (Local Area Network) with the 100 Base-TX/10 Base-T LAN unit on your computer. To activate the LAN unit, perform the following steps.   Never insert any cables, but a LAN cable, which have different electric characteristics from those of the LAN cable. Otherwise, the LAN unit and the cables may be damaged.  Use a category 3 or a category 5 LAN cable when connecting to 10 BASE-T LAN, and the category 5 when connecting to 100 BASE-TX LAN.  Connect Your Computer to LAN 1.  Turn off your computer. 2.  Attach the provided core to one end of your LAN cable. Insert the cable into the core and close the core until it clicks.  3.  Open the cover of the LAN jack on the left side of your computer.                            To avoid damaging the LAN unit, close the LAN jack cover after you finish using the LAN unit. LAN Jack LAN Jack Cover
 5-5 5 4.  Connect the core end of the LAN cable to the LAN jack and the other end of the LAN cable to the network hub.       Do not insert into the modem jack (with      mark). It will damage the LAN cable and the modem jack.  You can also directly communicate with another computer using a cross LAN cable.  5.  Turn on your computer.  Configuring LAN Unit 1. Click start – Control Panel. 2. Click Network and Internet Connections; then, Network Connections.  If Classic view is selected, double-click Network Connections icon. 3. Right-click Local Area Connection. 4.  From the pop-up menu, select Properties. 5. In the Local Area Connection Properties dialog box, set the network setting according to the instruction of your network administrator.   •  Attach the provided core to your LAN cable to insure compliance with requirements of EMC regulations for computing equipment. •  Make sure to log on your computer as a member of your Computer administrators group. Otherwise, you cannot set or change some settings for the LAN unit.    LAN Jack Core  LAN Cable (Straight Cable) To Network Hub
 5-6 5 If you cannot access the network,  1. Click start – Control Panel. 2. Click Performance and Maintenance; then, System. If Classic view is selected, double-click System icon. 3. Click Hardware tab; then, Device Manager button. 4. Double-click on Network Adapters string, then, Realtek RTL8139 xxxxx string. 5. Click Advanced tab, and select Link Speed/Duplex Mode in Property list and select an appropriate value in Value pull-down menu. 6. Click OK and close the Device Manager window.  7. Click OK and close the Control Panel window.
 5-7 5 Wireless LAN   Your computer has an integrated wireless LAN function compliant with IEEE 802.11b standard. You can access the network by the wireless LAN. There are two kinds of wireless networks: a network using an access point and a peer-to-peer wireless network. You can connect your computer to a wired LAN or the Internet through an access point that is also compliant with IEEE 802.11b standard. Peer-to-peer wireless network consists of a number of computers each equipped with wireless networking interface. Each computer can communicate directly with other wireless enabled computers.   The range to give reliable performance and the quality of connection vary depending on the environment where you perform.  To communicate through the wireless LAN, activate the integrated antennas with the following steps.  Activate Antennas You can enable/disable the antennas by pressing Fn +F1 key combination. When the antenna indicator ( ) lights green, the antennas are enabled. When the indicator light is off, they are disabled.    Antenna Indicator Antennas
 5-8 5 Connecting to the Internet via an Access Point You can connect your computer to the Internet or a wired network via an access point supporting IEEE 802.11b. Refer to the manual of the access point or consult your network administrator if you are not sure.   Communicating with Other Computers    •  Confirm each computer is enabled for wireless LAN first. •  Make sure to log on the computer as a member of the Computer administrators group. Otherwise, you cannot set or change some settings for wireless LAN. 1. Click start – Control Panel. 2. Click Network and Internet Connections – Network Connections. If Classic view is selected, double-click Network Connections.  3. Select Wireless Network Connection; then, click Change settings of this connection of Network Tasks. 4. Double-click on Internet Protocol (TCP/IP) string in This connection uses the following items. 5. In Internet Protocol (TCP/IP) Properties dialog box, select Use the following IP address and set a unique IP address to 192.168.1.2 through 192.168.1.254 and the Subnet mask to 255.255.255.0; then, click OK.   •  The IP address of each computer should be unique. •  The Default gateway can be blank.  6. Click Wireless Networks tab; then, Advanced button in the lower right of the dialog box. Advanced dialog box appears. 7. Select Computer-to-computer (ad hoc) networks only; then, click Close button. 8. Click Add… button in Preferred networks section of Wireless Network Connection Properties dialog box. 9.  Type a name of the network in Network name (SSID) field of Wireless Network Properties dialog box.   Confirm your computer and other computers are connecting to the same network. 10. Click OK twice; then, close the Control Panel window.
 5-9 5 11.  Configure the network by setting the name of your computer and workgroup.   To communicate with other wireless enabled computers, set the computer name and the workgroup name. The computer name should be unique and the workgroup name should be same as others.   Confirming the Status of the Wireless Connection  Before performing the following instructions, confirm the devices that you want to communicate with are enabled for wireless LAN.  1. Click Wireless Network Connection icon (  or  ) on the taskbar. If you cannot find the icon click   to show all kinds of icon. Connect to Wireless Network dialog box appears. If Wireless Network Connection Status dialog box appears, go to Step 4. 2.  Select a network you want to access in Available networks in Connect to Wireless Network dialog box; then, click Connect button.   When the network name you want to access does not appear, click Advanced tab; then, Refresh button of Available networks in Wireless Network Connection Properties dialog box; then, click OK.     3. Click Wireless Network Connection icon ( ) on the taskbar. 4. In Wireless Network Connection Status dialog box, confirm your connection status.   •  The number of green signals ( ) shows the connection. The more signals light on, the better quality is given to the computer. •  When the quality of connection is poor, adjust the distance between the computer and other devices or the access point you are communicating with and/or the facing direction of the computer.  Connecting the WEP configured network Wireless communication has security issues. Some networks are configured with WEP (Wired Equivalent Privacy) keys or encryption keys to protect the transmitted data. To connect into the network configured with WEP keys, follow the steps below. 1. Right-click Wireless Network Connection icon ( ) on the taskbar and click View Available Wireless Networks.
 5-10 5 2.  Select the network you want to connect from Available networks of Connect to Wireless Network dialog box. 3.  Type the encryption key set to the network in Network key and click Connect.   •  When you select a network that is not configured for encryption settings in the step 2, the Network key field is grayed and you do not have to enter the key characters.  •  When the key index set to your computer is different from that of the network, you cannot access the network. Set the same key index with the following steps. Note that some access points have the key index options 0 through 3. Refer to the table below for matching.   1. Open the Wireless Network Connection Properties dialog box.       (Refer to the steps in Communicating with Other Computer        section.)  2.   Select the network you want to access in Preferred networks section       and click Properties button. 3.   Confirm the box of Data encryption (WEP enabled) is checked,        uncheck the box of The key is provided for me automatically and       set the key index.                                             Key index compatibility table Access Point 1  Access Point 2  Your Computer 1 0 1 2 1 2 3 2 3 4 3 4                               (ex. When your access point type is “Access Point 2” and its key                                       index is set to 0, set 1 to the key index of your computer.)
 5-11 5 Network Setup Utility  With the Network Setup Utility, you can set up your specific network settings adjusted for your environments such as work, home, etc. and select the appropriate one to the environment. You can also change the network settings.   •  Not every setting item can be stored.  •  The Network Setup Utility may not compliant with all network environments.   Loading Network Settings To set your specific network settings, confirm that your computer is connected into the network and has the proper settings for your current environment and follow the instructions below. 1. Click start – All Programs – SHARP Network Setup Utility – SHARP Network Setup Utility. 2. Click OK.  3. Click Set, select SHARP icon or Windows icon, and then, click Select icon button. 4.  Select an icon and click OK. Type a network name, then, click OK. The selected icon appears in the Network Setup Utility window.   It takes a moment to load the network settings.    Switching Network  To switch the network set above, confirm your computer is ready to connect into the network and follow the instructions below. 1. Click start – All Programs – SHARP Network Setup Utility – SHARP Network Setup Utility. 2. Click OK. 3.  Select the appropriate network icon in the Network Setup Utility window. 4. Click OK.
 5-12 5  •  Make sure your computer is connected to the proper environment. •  If your hardware or software configuration has been changed, you may not be able to switch to the network properly. In this case, you may need to reconfigure the settings.  Changing Network Settings To change the loaded network settings, right-click on the icon you want to change the settings in the Network Setup Utility window and click Edit settings in the pop-up menu. Then, edit the settings.  Deleting Network To delete the loaded network settings, right-click on the icon you want to delete in the Network Setup Utility window and click Delete setting in the pop-up menu. Then, click OK.
 6-1  6 CHAPTER 6         Setup Utility  This chapter describes how to run the Setup Utility to change settings on your computer.  Running Setup Utility  With the Setup Utility, you can customize the system configuration information, such as time and date, port assignments, or passwords.  The information you have specified is saved in a special area called CMOS RAM, which the system reads every time you turn on your computer. Your computer is shipped from the factory with the appropriate setting of the Setup Utility. Leave it as default in normal use.  Contents of Setup Utility The Setup Utility consists of five menu pages, as follows: •  Main:   Configures basic setting   •  Advanced: Configures device interface  •  Security: Sets passwords •  Boot:  Defines where the system boots from  •  Exit:  Exits the Setup Utility or returns to the default values
 6-2  6 Entering and Exiting the Setup Utility 1.  Turn on your computer. 2.  When the message Press <F2> to enter SETUP appears, press F2. 3.  Change to the desired settings. Refer to the next section. 4. In Exit menu select one of the exit methods, and press Enter. 5.  Confirm the message and press Enter again. The system restarts.   When the Setup Utility is opened, power management does not work. Do not close the display cover.   Changing the Setting of the Setup Utility To change the settings: 1. Use → or ← key to select the menu; then, press Enter. 2. Use ↑ or ↓ key to select the item. On item with     mark, press Enter to open its sub menu. Press Esc to close the sub menu and return to the previous menu. Most of the items without     mark can be changed their values or status by pressing Enter when selected. For date and time, press Enter on the item to select the value you want to change, then, use minus key or space bar to change the value. 3.  Close the Setup Utility by following the steps above.
 6-3  6 Main Menu System Time defines the system time, using the format hour:minute:second (24-hour format).  Use Tab key to move the cursor, and minus key or space bar to change numerals. System Date defines the system date, using the format month/day/year. Use Tab key to move the cursor, and minus key or space bar to change numerals. Hard Disk Type shows the type of the hard disk of your computer. Press Enter to show the details. Internal NumLock defines whether the numlock keys of the built-in keyboard are always disabled or not. (Num lock indicator will turn on when Fn+NumLk are pressed regardless of this setting. An external keyboard will be numlocked if connected. )   USB Emulation defines whether USB devices (a keyboard, a mouse or an external floppy disk drive) can be used in DOS mode. (When it is set to Disabled, you cannot boot your computer from a floppy disk.)  Quick Boot defines whether the system skips the check of the internal memory while booting, to shorten the boot time. Quiet Boot defines whether the SHARP logo appears on the screen while booting. Video RAM Size shows the minimum size of the video memory.  CPU Information shows the information on the CPU. System Memory shows the volume of the conventional memory used in DOS mode. Always set to 640KB. Extended Memory shows the volume of the extended memory more than 1MB. BIOS Version shows the BIOS version of the system. EC/KBC Version shows the EC or keyboard controller version of the system.
 6-4  6 Advanced Menu Internal Pointing Device enables or disables the built-in glide pad. Resolution Expansion defines whether the Setup Utility screen is expanded when the resolution is 640x480 or 800x600.  Enabled means that the screen is expanded. Plug&Play O/S enables or disables plug & play function. Normally this option has to be set as default. PCI Configuration normally has to be as default.   Security Menu   Set Supervisor Password defines the supervisor password (up to eight characters). See the next section about the supervisor password.  Set User Password defines the user password (up to eight characters). See the next section about the user password.   If you lose your password, you will be unable to access your computer or change the configuration. Make sure to select a password you will never forget, or write it down and protect it in a secure place. Otherwise, you will have to contact your dealer for assistance.  Password on boot defines whether you have to type the password for booting your computer.   Hard Disk boot Sector defines whether the boot sector of the hard disk is write-protected. When formatting the hard disk or reinstalling software, set to Normal.   Supervisor and User Password Setting a password will protect your computer against unauthorized access. Once a password is set, the system requires the password when entering to the Setup Utility. And if Password on boot is enabled, the system will require a password when your computer is turned on.    If you enter a wrong password three times, the message System Disabled appears. Press the power button to shut down your computer, and after 10 seconds, press the power button to turn it on again.
 6-5  6  Your computer supports two different levels of password security: Supervisor password and User password. You cannot set a user password unless you have set a supervisor password. If you share your computer with others, we recommend that you set both the supervisor and the user password, and let others know the user password only.  With the user password, you can set System Time and System Date of the Main menu, Resolution Expansion of the Advanced menu, and Set User Password of the Security menu only.  Setting Password 1. In the Security menu of the Setup Utility, select Set Supervisor Password or Set User Password and press Enter.  2.  Type your password (up to eight characters), and press Enter.    3.  Type the same password again, and press Enter twice.  4. Select Exit menu and confirm Exit Saving Changes is highlighted; then press Enter.  5. Confirm Yes is highlighted and press Enter. The system restarts.  Changing Password 1. In the Security menu of the Setup Utility, select Set Supervisor Password or Set User Password and press Enter. 2.  Type your current password, and press Enter. 3.  Type your new password, and press Enter.  4.  Type your new password again, and press Enter twice. 5. Select Exit menu and confirm Exit Saving Changes is highlighted; then press Enter.  6. Confirm Yes is highlighted and press Enter. The system restarts.  Deleting Password 1. In the Security menu of the Setup Utility, select Set Supervisor Password or Set User Password and press Enter. 2.  Type your current password, and press Enter. 3.  Without typing any characters, press Enter.
 6-6  6 4. Press Enter twice. 5. Select Exit menu and confirm Exit Saving Changes is highlighted; then press Enter 6. Confirm Yes is highlighted and press Enter. The system restarts.  Boot Menu  Boot Sequence specifies the order in which your computer is to make a check for a device to boot the system. Press Enter to open the sub menu. The system boots from the drive at the top of the list. If the system cannot find the drive, it will boot from the second one; then, third one. Use arrow keys to select the drive you want to move; then, use minus key or space bar to move it up and down.  LAN Boot defines whether the system boots from other server via the LAN unit of your computer.  Wake On LAN defines whether the system boots up or resumes from System Hibernate when the LAN unit of your computer becomes active. This setting functions only when your computer is connected to AC power.   Exit Menu  Exit Saving Changes saves the settings you have changed and exits the Setup Utility.  Exit Discarding Changes exits the Setup Utility without saving the settings you have changed.  Load Setup Defaults returns the values of all items to the default.  To exit, select one of the above items.  Discard Changes returns the values of all items to the values you last saved. To exit, select one of the above two items.  Save Changes saves the settings you have changed. To exit, select one of the above two items.
Appendixes  A-1  Appendixes  The appendixes contain additional information on the use and care of your computer.  Memory Module   You can upgrade the memory size of your computer up to 768MB by installing a memory module. For available memory modules, contact your local dealer.   Installing Memory Module   •  Do not handle the memory module in the location where static electricity is easily generated such as on the carpet. •  Before installing the memory module, carefully discharge static electricity from your body by touching an unpainted metal area. •  Avoid touching the integrated circuits on a memory module. Handle all components by the edges. •  Keep the memory module in the anti-static wrapping until you are ready to install it.  1.  Turn off your computer, and disconnect the AC adapter and remove the battery pack and peripheral devices. See Chapter 3 for removing the battery.   •  Make sure to turn off your computer and remove the AC adapter. Otherwise you may get an electrical shock. •  After a long usage of your computer, the temperature inside your computer may be hot. Wait until it becomes cool.  2.  Close the display cover and turn over your computer on a stable surface.
 A-2  Appendixes 3.  Loosen two screws and remove the memory slot cover.  4.  Turn over the sheet and align the memory module as shown below, matching the notched part of the module with the projected part of the memory socket of your computer.       Notched Part Projected Part 20° Memory Slot Cover Screws Memory Socket Memory Module Sheet
Appendixes  A-3  5.  Press the memory module slowly to place it into the memory socket, matching the notched parts of the module with the projected parts of the socket, until you hear the clicking sound.  6.  Replace the sheet and memory slot cover, matching the projected parts of the cover with the notched parts of your computer.  7.  Tighten the screws.  8.  Replace the battery pack, turn over your computer and connect the AC adapter.  See Chapter 3 for replacing the battery pack. Notched Parts Projected Part Notched Parts Projected Parts
 A-4  Appendixes 9.  Open the display cover; turn on your computer and check the memory size; by clicking start – My Computer – View system information of System Tasks. Your memory size appears at the bottom of the sentence in General tab. Share video memory size will not be included with the value. Uninstalling Memory Module 1.  Follow steps 1-3 of Installing Memory Module. 2.  Turn over the sheet and slightly bend both latches outwards until the memory module is released.  3.  Remove the memory module and follow steps 6-9 of Installing Memory Module.   Installing Weight Saver You can change the optical drive unit for the weight saver to make your computer lighter. With the weight saver installed instead of the optical drive unit you can get the better portability.   Always keep either of the optical drive unit or the weight saver installed into the optical bay. Leaving the optical drive bay empty may damage your computer.  Installing Weight Saver 1.  Turn off your computer and disconnect the AC adapter from your computer.   Make sure to turn off your computer and remove the AC adapter. Otherwise your computer may be damaged.  2.  Close the display cover and turn over your computer on a stable surface. Latches
Appendixes  A-5  3.  Slide the optical drive stopper backward you and pull out the optical drive unit from your computer.      Keep the optical drive unit wrapped and in a safe place to avoid any damage.  4.  Install the weight saver into the bay until it clicks.    Re-installing Optical Drive Unit 1.  Turn off your computer and disconnect the AC adapter from your computer.   Make sure to turn off your computer and remove the AC adapter. Otherwise your computer may be damaged.  2.  Close the display cover and turn over your computer on a stable surface. 3.  Slide the optical drive stopper backward you and pull out the weight saver from your computer. Optical Drive Stopper Optical Drive Unit Weight Saver
 A-6  Appendixes 4.  Install the optical drive unit into the bay until it clicks.   Maintenance and Care This appendix provides you with information on how to maintain your computer in excellent working condition. Replacing Backup Battery Your computer is equipped a backup battery for keeping the information of the Setup Utility, etc. If you see the message Press <F1> to resume, <F2> to Setup, replace it with a Lithium CR2032 Battery on the market.  1.  Turn off your computer, disconnect the AC adapter, and remove the battery pack from your computer.   Make sure to turn off your computer and remove the AC adapter and the battery pack from your computer. Otherwise your computer may malfunction.   2.  Loosen the screws and remove the cover of the backup battery box.  Optical Drive Unit Cover Screws
Appendixes  A-7  3.  Remove the backup battery with a pointed staff.    Never use a metallic material. If the material touches to the circuit, your computer may malfunction.   4.  Insert a new backup battery with the plus side (printed a part number) up. Press two hooks of the box with the edge of the battery and hold it; then, press down the battery.  5.  Replace the cover on your computer matching the projected parts of the cover with the notched parts of your computer.  Hooks Notched Parts Projected Parts
 A-8  Appendixes 6.  Tighten the screws.  7.  Insert the battery pack. 8.  Turn your computer over and connect the AC adapter. 9.  Turn on your computer. 10.  If you see the message Press <F2> to enter Setup, press F2. 11.  In the Exit menu, select Load Setup Defaults; then, press Enter. 12.  When the message Load default configuration now? appears, select Yes; then, press Enter. 13.  In the Exit menu, select Exit Saving Changes; then, press Enter. 14.  When the message Save configuration changed and exit now? appears, select Yes; then, press Enter.  15.  Click start – Control Panel. 16.  Click Date, Time, Language, and Regional Options in Category view; then, click on Change the date and time string. 17.  Set date and time; then, click OK. 18. Close the Control Panel window.
Appendixes  A-9  Using Security Cable                                                                                                                       You can connect a security cable to the security slot on the right side of your computer to prevent theft.    Cleaning Computer  Cabinet Apply a small amount of mild cleaning solution to a dry, lint-free cloth and wipe the cabinet with the cloth.   •  Never clean your computer while it is powered on. •  Do not use alcohol, benzene, thinner or other strong chemical agents that may damage the cabinet.  Security Cable Security Slot
 A-10  Appendixes Screen The surface of the screen may become smeared and accumulate dust during use.  Avoid touching the screen with your fingers when using the system. Gently wipe the surface of the screen with a soft cloth that has been dipped in a mild detergent solution and squeezed dry.  Glide Pad Wipe the glide pad with a soft, dry cloth.  Ventilation Openings Dust on the ventilation openings may cause overheating of your computer. Wipe the ventilation openings with a soft, dry cloth.  Traveling with Your Computer  This computer is designed for portability. For safety and convenience when traveling, please follow these guidelines. •  Before traveling, back up your data onto floppy disks, optical disks or other external media. •  Do not travel with any peripherals such as an external floppy disk drive unit connected. •  Do not carry your computer powered on. This may result in loss of data and/or damage to the hard disk drive. •  Make sure the display cover is properly closed before traveling. Otherwise the cover may be opened unawares, and the display or the keyboard will be damaged. •  If you carry your computer in a bag, try to avoid unnecessary pressure, caused by the stuff of the bag, to your computer. •  Disconnect the AC adapter from your computer. •  Fully charge the battery pack, and bring the AC adapter and the AC power cord. •  Avoid sudden shocks or extreme vibration.
Appendixes  A-11  Re-installation Instructions  To recover your hard disk, you will use PowerQuest®EasyRestore™. Before starting re-installation, read the following End User License Agreement first.  PowerQuest(R) EasyRestore (TM) End User License Agreement  IMPORTANT:  Read this before using your copy of PowerQuest software.  This document is a legal agreement between you, the "end user," and PowerQuest Corporation. Use of the software indicates your acceptance of these terms. As used in this License Agreement, the term "Software" means the EasyRestore software included on the CD provided with this License Agreement.  1. PROPRIETARY RIGHTS. The Software is a proprietary product of PowerQuest Corporation ("PowerQuest") or its licensors and is protected under U.S. copyright laws and international treaty provisions. Ownership of the Software and all copies, modifications, and merged portions thereof shall at all times remain with PowerQuest or its licensors.  2. GRANT OF LICENSE. The Software is being licensed to you, which means you have the right to use the Software only in accordance with this License Agreement. The Software contains pre-installed software for disaster recovery purposes.  The Software is only authorized for distribution together with a specific computer. This License authorizes you to use the Software for disaster recovery purposes only, to restore the hard disk image contained on the CD to the computer with which the CD and Software were originally shipped.   3. NONPERMITTED USES. Without the express permission of PowerQuest, you may not (a) use, copy, modify, alter, or transfer, electronically or otherwise, the Software or documentation except as expressly permitted in this License Agreement, or (b) translate, reverse program, disassemble, decompile, or otherwise reverse engineer the Software.  4. TECHNICAL SUPPORT. PowerQuest is NOT responsible to provide technical support.  Any and all technical support questions, regarding the Software, should be referred to the place of purchase.  5. U.S. GOVERNMENT RESTRICTED RIGHTS. If you are acquiring the Software on behalf of any unit or agency of the United States Government, the following provision applies: It is acknowledged that the Software and the documentation were developed at private expense and that no part is in the public domain and that the Software and documentation are provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c)(1)(ii) of the Rights in
 A-12  Appendixes Technical Data and Computer Software clause at DFARS 252.227-7013or subparagraphs (c)(1) and (2) of the Commercial Computer Software-Restricted Rights at 48 CFR 52.227-19, as applicable. Contractor/manufacturer is PowerQuest Corporation/P.O. Box 1911/Orem, UT 84059.  6. NO WARRANTY. The Software is being provided to you AS IS.  PowerQuest does not warrant the Software to end users. If the Software fails to perform substantially in accordance with the documentation provided to your hardware supplier, PowerQuest will repair or replace the copy of the Software provided to your hardware supplier and will authorize your hardware supplier to provide such repaired or replaced Software to you without charge.  7. LIMITATION OF LIABILITY. NEITHER POWERQUEST NOR ITS SUPPLIERS SHALL IN ANY EVENT BE LIABLE FOR ANY DAMAGES WHATSOEVER ARISING OUT OF OR RELATED TO THE USE OF OR INABILITY TO USE THE SOFTWARE, INCLUDING BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, AND DAMAGES FOR LOSS OF BUSINESS PROFITS, BUSINESS INTERRUPTION, LOSS OF BUSINESS INFORMATION, OR OTHER PECUNIARY LOSS, EVEN IF POWERQUEST CORPORATION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES, WHETHER SUCH LIABILITY IS BASED ON CONTRACT, TORT, WARRANTY, OR ANY OTHER LEGAL OR EQUITABLE GROUNDS. BECAUSE SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO YOU.  8. NO WAIVER. Any failure by either party to this agreement to enforce a specific part of the agreement in a specific situation is not a waiver of rights under the agreement. The party may still enforce the rest of the agreement in that situation and may still enforce some or all of the  agreement in other situations.  9. This License Agreement constitutes the entire agreement between you and PowerQuest pertaining to its subject matter. This License Agreement is governed by the laws of the State of Utah. Any litigation arising from this license will be pursued only in the state or federal courts located in the State of Utah.  Copyright 1994-2003, PowerQuest Corporation. All rights reserved. U.S. Patents 5,675,769; 5,706,472; and 5,930,831; other patents pending in  the U.S.A. and elsewhere. PowerQuest is a registered trademark and  EasyRestore is a trademark of PowerQuest Corporation.
Appendixes  A-13   Preparation for Re-installation  You can format the hard disk and re-install the preinstalled software with the recovery CD-ROM, and set the status of your computer to the same configuration as shipped from the factory. The following items are necessary for re-installation: •    Product Recovery CD-ROMs •    Operation Manual   •  It will take about 15 minutes to complete the re-installation.  •  Use the Product Recovery CD-ROMs only for your computer.  •  The Product Recovery CD-ROMs are not for sale. Keep them in a secure place. •  Unless otherwise specified, the instructions in this booklet assume that you are installing Windows XP into the C:\WINDOWS directory.  Backing up the data Before formatting the hard disk, you should back up your data.  For details on how to back up your data, see the Windows Online Help.    Selecting the way to recover your system Your computer has two drives(C: and D:) in its hard disk when it was shipped from the factory. You can select the way to recover your system.  •  Recovers C: drive only. (Recommended) This process will format C: drive only and recover C: drive to the same status as shipped from the factory. Nothing will be done to D: drive. The volume of the drives will not be changed and current ones will be kept. •  Recovers both C: and D: drive.      This process will format both C: and D: drives, and contents of the hard disk are restored to its original state in C: drive. The volume of the drives will be back to the same as shipped from the factory. •  Formats hard disk and creates new partition. This process will format the whole hard disk drive and creates a new partition. You can select the volume of C: and D: drives. The contents of the hard disk are restored to its original state in C: drive.
 A-14  Appendixes Formatting the drives and re-installing Windows XP   1.  Make sure your computer is turned off. 2.  If any peripheral devices are connected to your computer, disconnect them.  3.  If the weight saver is installed in your computer remove it and install the optical drive. 4.  Connect the AC adapter; then, turn on your computer.    Be sure to connect the AC adapter. If the battery power becomes significantly low, the installation process will be canceled.  5.  When the message Press <F2> to enter SETUP appears, press F2. The Setup Utility opens. 6.  Insert the Product Recovery CD-ROM disk 1 into the optical drive.  7. In the Exit menu, select Load Setup Defaults; then, press Enter twice. 8. In Boot Sequence of the Boot menu, set CD-ROM Drive to the top of the list; then, press Esc. 9. In the Exit menu, confirm Exit Saving Changes is highlighted and press Enter twice. The system restarts.   10.  Read the message on the screen, and select the way to recover your system; then, press Enter. If you selected Formats hard disk and creates new partition, go to the next step. Otherwise, go to Step 12. 11.  Select the volume of C: drive and press Enter.  12.  Read the message and select Continue; then, press Enter.    Although the pointer may be shown on the screen, never touch the keyboard or the glide pad during recovery except when the message prompts you to. If you touch them, the re-installation will be canceled.  13.  If you see the message asking you to replace the CD-ROM, remove the Product Recovery CD-ROM disk 1 and insert the Product Recovery CD-ROM disk 2, then, click OK. 14.  If you see the message asking you to replace the CD-ROM, remove the Product Recovery CD-ROM disk 2 and insert the Product Recovery CD-ROM disk 3, then, click OK.
Appendixes  A-15  15.  When the message Press <F2> to enter SETUP appears, press F2. The Setup Utility opens. 16. In the Exit menu, select Load Setup Defaults; then, press Enter twice.  17. In the Exit menu, confirm Exit Saving Changes is highlighted and press Enter twice.  The system will restart again. 18.  Set up Windows XP by following the instructions on the screen. When you finish the setup, the recovery is completed. Make sure to set date and time.
 A-16  Appendixes
 T-1 Troubleshooting Troubleshooting  This chapter describes how to troubleshoot computer problems.  Common Problems Problems with your computer can be caused by something as minor as an unplugged power cord or as major as a damaged hard disk drive. The information in this troubleshooting section is designed to help you find and solve minor problems. If you still have a problem after trying all the suggested remedies in this chapter, contact your dealer.  The problems that you might encounter can be divided into two basic categories: hardware and software. Hardware problems can be further divided into being of an electrical or a mechanical nature. You will know you have a hardware problem if, for example, the screen is blank, or your computer cannot recognize the disk drives.  Software problems can occur at several levels. Both your operating system and your software application programs are capable of generating errors and error messages.  If you encounter a software error, try to determine if the error message is from your operating system or from an application program, and refer to the appropriate manual for possible remedies.  You can also refer to the Windows manual or Windows help program to solve the problem. To access the help program, click start – Help and Support. It also gives you troubleshooting tips and an index.  Successful troubleshooting is the result of careful observation, deductive reasoning, and an organized approach to solving the problem. If you encounter a problem, begin by performing a careful visual inspection. Check the exterior of your computer first. If no lights are displayed, check the battery charge or power outlet, the plug and power cord, and any power switches that may affect your computer. If your computer has been connected to any peripheral devices, look for loose or disconnected cables. You may also need to check the fuses and breakers in your electric box. A few common problems and suggested solutions are presented in the examples that follow.
Troubleshooting T-2  Trouble when Starting  Question: Why doesn't the power indicator or the battery indicator turn on? •  Make sure the AC adapter is correctly connected to the AC adapter jack of your computer. •  Make sure the AC power cable is correctly connected to a live wall outlet. Connect another electric equipment to the wall outlet and check whether it is live or not. •  Make sure the battery pack is correctly installed and charged. •  If the battery pack is discharged, connect the AC adapter. •  If all the steps above failed, follow the instructions on Why doesn't the keyboard or the glide pad function?  Question: Why do I get the message Invalid system disk? •  You may have inserted a non-bootable disk in the external floppy disk drive unit (either a defective disk or one without an installed operating system). Remove the disk.  Question: Why can’t I boot from the floppy disk? •  Make sure that the external floppy disk drive unit is correctly connected to your computer. •  Check whether the floppy disk set to the external floppy disk drive unit contains a system disk.   •  Check whether USB Emulation in Main menu of the Setup Utility is enabled. (Refer to Main Menu in Chapter 6.) •  Check whether Floppy Disk Drive in Boot Sequence in Boot menu of the Setup Utility is set to the top of the list. (Refer to Boot Menu in Chapter 6.)  Question: Why do I get the message Press  <F1> to resume, Press  <F2> to setup? •  The setting of the Setup Utility is deleted. Run the Setup Utility and get default value of the Setup Utility. Be sure to set the date and time correctly.
 T-3 Troubleshooting•  If you often see the message, the backup battery has no capacity left.  Replace the backup battery with the steps in Replacing Backup Battery of Appendixes.  Question: Why do I get the message Operating system not found? •  Run the Setup Utility and get default value of the Setup Utility. Be sure to set the date and time correctly.   Trouble with Display  See also the Display section in Chapter 2 and 4.   Question: Why is the screen blank? •  Press any key to see if any power management feature has turned off the screen to save power. •  See the power indicator to check whether your computer is turned on. •  If you are using a battery pack, make sure it is correctly installed and has a charge remaining.  •  Make sure the LCD screen is selected as the display by pressing Fn+F5 (). •  Check whether the display is on by pressing Fn+F11 (). •  If you still have the problem after trying the above, follow the steps in Why doesn't the keyboard or the glide pad function?  Question: Why does the external monitor display nothing or the image on it distorted? •  Confirm the monitor is turned on. •  Confirm the monitor is connected correctly. •  Make sure an external monitor is selected as the display by pressing Fn+F5 (). •  If you use Fn+F5 () to change the display, the image may be distorted. Press Fn+F5 () again to return the previous display and use Display Properties dialog box to change it again. •  Make sure the value of Screen resolution in Settings tab of Display Properties is same as or lower than the resolution of the external monitor.
Troubleshooting T-4  •  Make sure the external monitor is not near any electric devices having strong magnetic fields such as a TV set or radio. •  Do not share an outlet with a TV set or radio.   Question: Why does the TV set display nothing or the image on it distorted? •  Confirm the TV is turned on. •  Confirm the TV set is connected correctly. •  If an external monitor is connected to your computer, disconnect it. •  Make sure TV is selected as the output display by using Display Properties dialog box. (Refer to Displaying Video on Your TV Set section in Chapter 2.) •  Confirm the Screen resolution is set to 800 by 600 pixels and Color quality to Medium (16bit).  Question: Why can’t I change the display with Fn+F5 keys? •  When playing the animation or game, Fn+F5 () key combination may not work. Close the currently running application. •  When running DOS in the full screen mode, Fn+F5 () key combination may not work. •  Use Display Properties dialog box to change it. •  When connecting to a TV set, Fn+F5 () key combination does not work.   Trouble with Keyboard/Glide Pad  Question: Why doesn't the keyboard or the glide pad function? •  Try the following in this order: 1. Press Ctrl+Alt+Delete and select Users tab of Windows Task Manager dialog box. Click Disconnect or Log Off; then, Yes. 2.  If the step1 fails to work, press the power switch for more than four seconds to            turn off the system. Ten seconds later, turn your computer on.
 T-5 Troubleshooting3.  If you still cannot turn off the system with the power switch, press the reset            switch on the bottom of your computer to turn off the system (refer to Resetting System section of Chapter 2). Ten seconds later, turn on your computer by pressing the power switch.   Question: Why does the glide pad malfunction? •  The surface of the glide pad or your palm may be moist or dirty and grease. Wipe the glide pad with a soft, dry cloth.  Trouble with Floppy Disks  Question: Why can't I use a floppy disk? •  Confirm the external floppy disk drive unit is correctly connected.  •  Confirm the floppy disk is inserted correctly.  •  Confirm the drive or file name is correct. •  The floppy disk may not be formatted or could be corrupted. Format the disk or use another disk. •  If you cannot write to a floppy disk, the disk may be write-protected. Eject the disk and ensure that the write-protect tab covers the detection hole. •  If you cannot write to a floppy disk, the disk may be full. Use another disk.  Trouble with the Hard Disk  Question: Why can't I read or write data to/from the hard disk? •  Confirm the drive and file names are correct. •  Confirm the hard disk has sufficient free space.  Trouble with the Optical Drive  Question: Why can’t I read data from a compact disc or play files? •  Confirm the CD is inserted correctly. •  Confirm the drive and file names are correct. •  Confirm the CD is not stained or scratched. •  Confirm the CD or files are supported.  •  Confirm the optical drive unit is correctly installed to your computer.
Troubleshooting T-6   Question: Why the drive does not open? •  Confirm the optical drive unit is correctly installed to your computer. •  Confirm your computer is turned on.  •  When your computer is turned off, insert a fine rod into the drive tray ejection hole.  Question: Why can’t I read data from a disk or play files? •  Confirm your computer is turned on.  •  Confirm the disk is inserted correctly. •  Confirm the drive and file names are correct. •  Confirm the disk is not stained or scratched. •  Confirm the disk or files are supported.  Question: Why doesn’t the DVD video play smoothly? •  Ensure to use AC power. •  Set back the screen resolution, color quality, and screen refresh rate to the default value. See the specifications on the supplement for the default values of your computer. •  Power management may be working.  Disable it.  Question: Why isn’t the optical drive recognized? •  If your computer is turned on with some kinds of DVD disks inserted in the drive, the drive may not be recognized. In this case, turn off your computer and open the disk tray by the way on Question: Why does not the drive open? on the previous page. Remove the disk from the drive; then turn on your computer again.
 T-7 Troubleshooting Trouble with Communication  Question: Why can't I communicate through the built-in modem? •  If your computer is turned on with some kinds of DVD disks inserted in the drive, the drive may not be recognized. In this case, turn off your computer and open the disk tray by the way on Question: Why does not the drive open? on the previous page. Remove the disk from the drive; then turn on your computer again. •  Confirm the telephone line is properly connected to the modem jack. •  Confirm the dial setting (pulse or tone) of Windows XP and/or communication software is matched with the telephone line. •  If you set your connection status using New Connection Wizard, check Use dialing rules in the Properties dialog box of that connection status. Refer to Internet Connection section of Chapter 5.  •  Confirm the country/region setting is appropriate. •  Confirm the network configuration is appropriate. •  Confirm the user name or password is correct. •  Confirm the COM port in the communication software is set appropriately. •  Turn off the power management in the Windows.  •  If an unusual device is attached to the line you are connecting to, the modem may not function properly. Remove the device or contact the dealer of the device. •  If your computer is connected to a PBX, consult the PBX maintenance staff or its service company. If the electric characteristics of your PBX are different from those of a regular analog line, the modem will not function properly. If you connect the modem to a digital PBX, both the modem and the PBX may be damaged.  Question: Why is the access speed so slow? •  Close the applications currently opened. •  Try to connect another ISP (Internet Service Provider), or try to connect in some other time.   Question: Why can't I access the LAN? •  Confirm the cable is properly connected to the LAN jack and the network hub. •  Confirm the network configuration is appropriate. •  Confirm the user name or the password is correct.
Troubleshooting T-8   Question: How can I detect the MAC address? •  Follow the instructions bellow: 1. Click start – All Programs – Accessories – Command Prompt. 2. Type ipconfig/all; then, press Enter. The IP information appears. 3.  See the numbers of Physical Address in Ethernet adapter Network Adapters section. 4. Type exit; then, press Enter.  Question: Why can't I detect the access point on my computer? (for wireless LAN model only) •  Confirm the access point is powered on. •  Restart your computer. •  Confirm your computer is enabled for the wireless LAN.   •  Detect the access point by following the steps below 1. Click start – My Computer. 2. Select My Network Places in Other Places; then, View network connections in Network Tasks. Network Connections dialog box appears. 3. Right-click Wireless Network Connection; then, click Disable. 4. Right-click Wireless Network Connection; then, click Enable.  •  When you have more than one available access points, your computer may be connected to other than right one you want to access:     1. Right-click ( ) icon on the taskbar; then, click View Available Wireless Networks. 2.  Select the desired network in the Available networks list; then, click Connect button.  Question: Why can't I connect to the network via an access point? (for wireless LAN model only) •  Confirm Any available network (access point preferred) is selected in Networks to access of Advanced dialog box.
 T-9 Troubleshooting•  Confirm the ESSID of your computer matches the ESSID of the access point you want communicate with. •  Confirm the WEP key is correctly entered if the WEP security of the access point is enabled.  Question: Why can't I communicate with other computers through a wireless LAN (for wireless LAN model only)? •  Confirm each computer is enabled for wireless LAN. •  Confirm Computer-to-computer (ad hoc) networks only is selected in Networks to Access of Advanced dialog box of each computer. (To open Advanced dialog box, refer to Communicating with Other Computers section of Chapter 5.) •  Adjust the distance between the computers by bringing your computer closer to others and remove any obstructions that may impede the communication; then, try to connect again. (The distance between computers or access points should be less than approximately 60m (190 feet), in direct line of sight.) •  Confirm the IP address, the subnet mask and the default gateway of each computer are set correctly. •  Confirm the WEP key is correctly entered if the WEP security of other devices, which you want to communicate with, is enabled.   Trouble with Peripherals  Question: Why don't peripheral devices function? •  Confirm they are correctly connected to your computer. •  Confirm they are Windows XP compliant. •  Confirm drivers necessary for the devices are installed.
Troubleshooting T-10  Question: Why can't I print? •  Make sure the printer is turned on. •  Check whether your computer and the printer are connected correctly. •  Check whether the printer is ready to print. •  Check whether the printer has enough paper. •  Check whether the printer driver is installed. •  Click start - Control Pane - Printers and Other Hardware – Printers and Faxes. If Classic view is selected, double-click Printers and Faxes icon. Confirm your printer is installed. If not, click Add a printer of Printer Tasks to install it. •  See also the Windows help program by clicking start - Help and Support.  Question: Why don't peripheral devices function correctly? •  Set System standby/hibernate to Never in Power Options Properties dialog box. If this does not work, set Turn off hard disks to Never. •  Confirm they are Windows XP compliant. •  Confirm drivers necessary for the devices are installed.
 T-11 TroubleshootingOther Troubles  Question: Why is the battery pack discharged so quickly? •  Initialize the battery pack.  Question: Why is the date and/or time incorrect? •  Correct the date and time in Windows. Double-click the time appearing on the taskbar and set them in Date and Time Properties dialog box.  Question: Why can't I use a hardware device? •  Make sure the hardware device is not crossed out with an X mark using the following procedure.  1. Click start – Control Panel. Click Performance and Maintenance; then, System. If Classic view is selected, double-click System icon. 2. Click Hardware tab; then, Device Manager. 3.  Double-click the device you cannot use and confirm Use this device (enable) appears in Device usage.
Troubleshooting T-12  Question: Why can't I produce sound? •  Turn the volume control on the left side of your computer backward to increase the output volume. •  Click or double-click the speaker symbol on the taskbar and check the Windows volume.   Question: Why can't I turn off my computer? •  Follow the instructions on Why doesn't the keyboard or the glide pad function?  Question: Why my computer is so hot? •  When charging the battery pack, its surrounding area or the front of the keyboard may become hot, but this is not a problem.  Question: Why can’t I record the sound from the microphone? •  Follow the instructions below: 1.  Double-click the speaker symbol on the taskbar. 2. Click Options and select Properties. 3. Select Recording in Adjust volume and confirm Microphone is checked in Show the following volume controls, then click OK. 4. Confirm Select is checked in Microphone of Recording Control dialog box. 5. Close the Recording Control dialog box.   Question: Why can’t find the drivers and applications? •  You may accidentally remove them. They are stored on the last recovery disk. (i.e. when two recovery CDs are provided, they are stored on the “Disk 2”.) When you are not sure how to install them or the CD does not have the drivers or applications, consult local service staff.
  Index-1 Index  Index   A AC adapter connecting, 1-2 using, 2-2 Account creating, 2-19 switching, 2-19 Audio connecting audio equipment, 4-8, 4-9 connecting headphone, 4-9 connecting microphone, 4-10  connecting speakers, 4-7 controlling output volume, 2-15 B Backup battery, A-6 Battery pack Add-on battery pack, 3-6 changing, 3-4 charging, 3-2 checking level, 3-2, 3-9 conditioning, 3-4 indicator, 2-1 3-3 insralling, 1-1 low battery indication, 3-3 C Cleaning computer, A-9 CD handling, 2-7 inserting, 2-8 removing, 2-9 troubleshooting, T-5 CD-R/RW, 2-10   D Display changing brightness, 2-16 changing resolution, 2-17 changing number of colors, 2-17 switching the display, 2-6, 4-7 troubleshooting, T-3 turning off, 2-6 DVD-ROM parental control, 2-12 playing, 2-13 region code, 2-11  troubleshooting, T-6 E External monitor connecting, 4-6 disconnecting, 4-6 displaying, 4-6 switching the display, 2-6, 4-7 F Floppy disk ejecting, 4-4 formatting, 4-5 handling, 4-3 inserting, 4-4 troubleshooting, T-5 Floppy disk drive  connecting,  4-3 disconnecting,  4-5 troubleshooting, T-5
  Index-2   Index G Glide pad changing configuration, 2-5 clicking and double-clicking, 2-5 drag and drop, 2-5 scroll, 2-5 troubleshooting, T-4 H Hard disk drive troubleshooting, T-5 I IEEE 1394 device connecting, 4-15 disconnecting, 4-16 Indicators battery, 2-1 power, 2-1 status, xiv K Keyboard function keys, 2-6 special keys, 2-6 troubleshooting, T-4 windows key, 2-6 L LAN configuring, 5-5 connecting to network, 5-4 troubleshooting, T-8 M Memory module installing, A-1 uninstalling, A-4 Modem configuring, 5-3 connecting to telephone line, 5-2 troubleshooting, T-7 N Network setup utility changing, 5-12  deleting, 5-12 loading, 5-11 switching, 5-11  O Optical drive  troubleshooting, T-5 P Passwords changing, 2-21, 6-5  deleting, 2-21, 6-5 setting, 2-20, 6-5  PC cards ejecting, 4-13 inserting, 4-12 Peripherals  audio equipment, 4-8 connecting guidelines, 4-1 external floppy disk drive, 4-3 external monitor, 4-5 headphones, 4-9 IEEE 1394 device, 4-15 microphone, 4-10 PC cards, 4-12 printer, 4-14 speakers, 4-7 television set, 2-13 troubleshooting, T-9 USB device, 4-11 Power choosing AC or battery, 2-1 indicator, 2-1 Power management controlling CPU speed, 3-11 disabling, 3-14 stopping power supply to display, 3-10 stopping power supply to hard disk, 3-10 system hibernate, 3-12 system standby, 3-12 Printer, 4-14
  Index-3 Index R Resetting power switch, 2-3 reset switch, 2-3 S Screen Saver, 2-18 Setup utility advanced menu, 6-4 boot menu, 6-6 entering and exiting, 6-2 exit menu, 6-6 main menu, 6-3 running, 6-1 security menu, 6-4 Security cable, A-9 S/PDIF compliant digital audio,4-8 Status indicators, xiv System hibernate  about, 3-12 generating conditions, 3-13 resuming from, 3-12 supporting, 3-13 System standby about, 3-12 generating conditions, 3-13 resuming from, 3-12 T Television set, 2-13 Troubleshooting common problems, T-1 communications, T-7 display, T-3 external floppy disk drive, T-5 hard disk drive, T-5 keyboard or glide pad, T-4 LAN, T-7 optical drive, T-5 peripherals, T-9 U USB device, 4-11 W Wallpaper, 2-18 Weight saver, A-4 WEP key, 5-9 Windows XP first-time setup, 1-4 properties dialog boxes, 1-5 Wireless LAN activating, 5-7  communicating, 5-8 conflicting the status, 5-9 connecting to Access points, 5-8
FCC RF Exposure Requirements: This device complies with the FCC RF exposure requirements.

Navigation menu