Sensys Networks FLEXSPP Traffic Sensor System User Manual Quick Start Guide

Sensys Networks, Inc. Traffic Sensor System Quick Start Guide

Contents

Quick Start Guide

1608 4th Street Suite 200 Berkeley CA 94710| info@sensysnetworks.com | P 510.548.4620 F 510.548.8264 1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com| P 510.548.4620 F 510.548.8264 Quick Start Guide: Access Point Controller Card (APCC) Set Up1Download the installation package from the Sensys Networks website: http://www.sensysnetworks.com/products/trafcdot. Double-click on TrafcDOT2.exe and click Run.Download & Install SoftwareCable the devices together with Cat5 cables. Turn on controller.Note: Until Master Mode is on, the Power and Link light will be off.Connect Cables• Internet access is required to download TrafcDOT2 and Adobe Air, or you need an ofine version of Adobe Air and TrafcDOT2 same subnet as AP/APCC.• You must be able to change network setting of your laptop.RecommendationsClick the checkboxes to select desired preferences. Click Continue to accept the default installation location. Note: Click the folder icon to select another location for TrafcDOT installation.Select Installation Preferences
1608 4th Street Suite 200 Berkeley CA 94710| info@sensysnetworks.com | P 510.548.4620 F 510.548.8264 1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com| P 510.548.4620 F 510.548.8264 ConnectClick the TrafcDOT icon to start the conguration program.Run TrafcDOTQuick Start Guide: Access Point Controller Card (APCC) 2Select an APCC IP Address and click Connect.Type in IP AddressCheck Master Mode for each installed SPP radio and then click Turn On Selected SPP(s).Note: Once Master Mode is on the Power LED on APCC isolator should be on and the Link light should blink about every second.Select Master ModeClick Yes to save to ash memory. Save Changes
1608 4th Street Suite 200 Berkeley CA 94710| info@sensysnetworks.com | P 510.548.4620 F 510.548.8264 1608 4th Street Suite 200 Berkeley CA 94710 | info@sensysnetworks.com| P 510.548.4620 F 510.548.8264 RunQuick Start Guide: Access Point Controller Card (APCC) Click the Radio window:1. Select RF Channel. The entries in the RF Channel drop-down list correspond to the 16 channels available for use. Select an entry from the list by clicking it. The factory default channel is zero.2. Click Apply.Set RF ChannelClick on the APCC to open the Access Point Conguration Panel.Open AP Cong Panel3Click Yes to save to ash memory. Save Changes
Sensys Networks and the Sensys Networks logo are trademarks of Sensys Networks, Inc. All other trademarks are the property of their respective owners.Information contained herein is believed to be reliable, but Sensys Networks makes no warranties as to its accuracy or completeness. Copyright © 2015 Sensys Networks, Inc. • ALL RIGHTS RESERVED • P/N 152-240-030-008 Rev DLocal DistributorQuick Start Guide: Access Point Controller Card (APCC) ManageClick the Other tab (a), specify Time Zone (b), click Save to AP(c).Click the System Cong tab to open the System Conguration Panel.Open System Cong Panel Start Controller Link & Set Time Zone• The default radio channel of the access point and sensors is Channel 0 (zero).• All sensors or repeaters on the APCC’s channel are found on the Map View Tray or Table windows. Unassigned devices will not show up on the map itself.• Green icons indicate normal, expected operation.• Use the conguration panel options to further congure the system.Note: Refer to the Sensys Networks Wireless Vehicle Detection TrafcDOT 2 Set Up and Operating Guide for more informationMain Windows4

Navigation menu