Selex ES 774-0850NB VS3000 GTW/ 806-870 User Manual VS3000 FPG3 MAN 0205 01 QRG A3 pm6

Selex ES SPA VS3000 GTW/ 806-870 VS3000 FPG3 MAN 0205 01 QRG A3 pm6

Contents

user manual

P/N MAN-0698/01.01P/N MAN-0698/01.01P/N MAN-0698/01.01P/N MAN-0698/01.01In the vehicular configuration: during normal operation theknob has the volume control function, turn it clockwise toturn up the volume (16 levels) of the audio output of theloudspeaker/earphone.Turn the knob counterclockwise to decrease the volume.If the knob is kept pressed until the alternate symbols Sand appear on the display it goes to group-channelselection function. Once in this modality turn the knob tochoose among the available groups and select the group-channel by pressing the knob. Once pressed the knob yougo back to volume control function. If, in group-channelselection modality, no operation on the knob is performed fora pre-defined time interval, the knob automatically changeoversto volume control function. Each changeover of knob functionis signalled to the operator by means of a confirmation beep.In the Motorcycle configuration: the triple pushbutton allowsthe same operativity of the knob.(“+” to increase the volume/scroll up the groups;“-” to decrease the volume/scroll down the groups;“•” to switch from volume control to group selection/OK).Lit while the radio is receiving.Lit while the radio is transmitting; blinking while the tran-smission is inhibited (only TETRA).When a symbol, or a writing, is present on the display nearthe key, by pressing the key you select the functionassociated to the relative symbol/writing.To scroll up/down the menu items, select the optionand escape.The off hook green key is used to accept/make (afterhaving typed in the address) an individual full duplex calland if pressed in idle status accesses the calls list.The on hook red key is used to end the connection. It isalso used to switch on/off the radio if kept pressed for afew seconds.Alphanumeric keypad for dialling numbers and/or strings.It is made up of 12 keys (10 digits plus and ).Clear/escape key.Only for TETRA: if a group is selected, by pressing theyellow key the writing "Dispatcher" on the display appears:now, by pressing PTT (if the network allows this function)the first available dispatcher of the selected group is called(not the group). By pressing again the yellow key the nameof the selected group appears on the display and bypressing PTT the selected group is called. If no group isselected the yellow key allows to make an (half duplex)individual/group call by pressing PTT (after having typedin the address) even if the PTT default modality is set (byPRP) for group/(half duplex) individual call.The key allows to switch the audio from the externalloudspeakers to handset accessory and viceversa. (Activeonly if the external loudspeaker and the handset areconnected to the radio).It lets the user send an emergency alarm.To be connected to audio accessories.To be connected to USB-A mass storage device (for FPG3software download).Push-To-Talk button, press it to talk during half duplexconversation.If pressed (in Idle status when a group-channel is se-lected, or after having typed in a group-channel address)it sends the call to the group-channel. See also the yellowkey function description.Signal level (TMO and GTW mode)Network, searching network (flashing)Direct Mode with Gateway equipment presence detectedFallback ModeDirect ModeRepeater Mode (Repeater only)Gateway Mode (Gateway only)Direct Mode with Repeater equipment presence detectedPacket Data ContextPacket Data ChannelE2E Crypto EnableCustom E2EE ErrorCustom E2EE EnableNo read Messages, Full queue with at least one message notread (flashing)Full Queue, each message is readActive Data CallBluetooth ActivatedEarphone Speech CallActive Speech CallKeypad Volume OffKeypad LockedGroup scanning EnabledGroup Attach FailureSDS and voice communication monitoring (Repeater only)Voice communication monitoring (Repeater and Gateway only)SDS monitoring (Repeater only)Helmet detectedRotary Knob EnabledTx ActiveUHF Network ChannelUHF Simplex ChannelLoudspeaker Audio OutputEarphone Audio OutputMenu structure© 2010 SELEX Communications S.p.A. - All rights reserved.SELEX Communications S.p.A. reserves the right to change specifications, performance or features relevant to the product describedwithout notice. This is an unpublished work the copyright in which vests in SELEX Communications S.p.A. The information containedherein is confidential and the property of SELEX Communications S.p.A. and is supplied without liability for errors or omissions. Nopart may be reproduced, disclosed or used except as authorised by contract or other written permission.TETRA - Mobile Radio TerminalQuick Reference GuideControls, indicators and connectorsVS3000-FPG3Displayed symbols SELEX Communications S.p.A. A Finmeccanica CompanyVia Pieragostini, 80, 16151 - Genova, ItalyDRGMMVolumeController/Group -channelSelectorGreen LEDRed LEDFunction KeysMenunavigationkeysOff hook keyOn hook keyAlphanumerickeypadClear keyYellow keySwitch audiokeyEmergency key12 pinsconnectorUSB connector(only vehicular)PTT (Notlocated on theFPG3 frontpanel)Menu NOTES:- Some menus can be or not available according to the configuration ofthe radio terminal.- Choosing some options of WPS menus can cause the ending of activegroup calls.E2EE Status (enable/disable E2EE)E2EE KeyIn Box (TMO, DMO, REP, FM)Out Box (TMO, DMO, FM)Text Message (TMO, DMO, FM)Send Status (TMO, DMO, FM)Char Size (TMO, DMO)Messages (TMO, DMO, REP,FM)Change Mode (TMO, DMO,REP, GTW, FM)Encryption (TMO, and DMO only)Phone ListsSettingsMonitor (to check radio coverage,FM only)GPSInformationHelpPhone Book(user defined TMO andDMO only)Home TETRA(pre-configured phonebook TMO and DMO onlyNon TETRA(pre-configured phonebook, TMO only)Group(To see the configured groups, FM only)Group Management(TMO, DMO and GTW)Calls (TMO and DMO only)Delivery Options(to select the kind of messages deliveryreport, TMO and DMO)Tx Inhibit(to disable/enable the transmission, TMOand DMO only)PreferencesBluetooth (TMO only)Speech Monitor(to enable/disable the functionality; REP andGTW only)SDS Monitor(to enable/disable the functionality; REPonly)Auxiliary Microphone(to configure the kind of auxiliary microphone,TMO, DMO and FM)Full Duplex(to set the type of full duplex: real or pseudofull duplex, TMO only)Group Scanning(to enable/disable it, TMO and DMO only)WPS Selection (TMO, DMO and GTW)WPS Update (TMO, DMO and GTW)WPS Reconfigure (TMO, DMO and GTW)Active WPS(to change the configuration ofthe active WPS)Extra WPS(to move the groups assignedby DGNA in the current WPS)WPS Data(to modify the current WPS parameters)Group Data(to modify the groups parameters)Late Entry(to enable/disable the function)Communication(with/without ack, DMO only)Send TPNI(enable/disable, DMO only)Group Call(to select the type of group call, TMO only)Dial Mode(to select the dialling modality)Call Identification(to choose if send or hide its own radio identifier,TMO only)Gateway <0>, <9>(to select the default gateway from the gatewaylist, TMO only)Pin(to change/enable/disable it)LanguageSounds(to disable and to control the soundsvolume)Display(to configure display settings)Presence Signalling(to enable/disable the presence signaltransmission; REP only)Hands FreeLemoKey Access(direct access keys are shown)Dialling(dialling digits are shown; TMO andDMO only)Supplementary String(supplementary strings are shown;TMO and DMO only)Symbols(symbols meaning is shown)Activation/DeactivationDevicesActive ConnectionsOffered ServicesFind NewDevices ListBacklight(to change the display backlight modality)Zoom(to zoom in/zoom out the display)& FMBefore using the equipment, read all theinstructions contained in the manual and, withspecial care, those relative to safety.Two versions are available:• VS3000-FPG3 Vehicular configuration• VS3000-FPG3 Motorcycle configurationSee the Safety Recommendation guide for FCC Approval.
P/N MAN-0698/01.01P/N MAN-0698/01.01P/N MAN-0698/01.01P/N MAN-0698/01.01How to...Access the send status menu, pressing the key associatedwith S when the radio is in idle status or selecting from mainmenu: Messages →→→→→ Send Status.Select the status to be sent, then select an user by means of thekey associated with or a group by means of the key asso-ciated with . To send the message use the key or selectthe Send option.Access the text messages selecting from main menu Mes-sages →→→→→ Text Message. Create a new message or select apredefined message then select OPT →→→→→ Send.Select an user ( ) or a group ( ) and send the message bymeans of key or selecting the option Send. During theediting of a message it is possible to change from uppercaseto lowercase pressing the key .Access the received messages list from main menu selectingMessages →→→→→ Inbox. Use the keys , to scroll the listof messages. The received messages can be status S or text messages. Select the message to be read (VIEW) andthen OPT to choose among Delete-Reply-Reply+History.From idle status press key to display the list of the last 20received/made individual calls. Scroll them by means of keys, . It is possible to recall the subscriber pressing thekey followed by the PTT pressing (Half-Duplex call) orfollowed by the pressing of the key (Full-Duplex call, TMOonly).It is possible to go back in a group call which is still active andfrom which you have disconnected: in TMO by pressing thePTT and in DMO by keeping pressed the key .From main menu select Settings →→→→→ Speech monitor, tochange the function status. If the speech monitor is active theuser will be asked to deactivate it and vice versa. By pressingthe key corresponding to YES the change is confirmed; by press-ing the key corresponding to NO or the key the user can exitthe menu without modification.From main menu select Settings →→→→→ SDS monitor, to changethe function status. If the SDS monitor is active the user will beasked to deactivate it and vice versa. By pressing the key cor-responding to YES the change is confirmed; by pressing thekey corresponding to NO or the key the user can exit themenu without modification.From main menu select Settings → → → → → Preferences →→→→→Presence Signalling To enable the transmission of presencesignal select PsOn; select PsOff to disable it.From main menu select GPS. The data relative to vehicleposition will be shown on the display.Activate Bluetooth functionality selecting Settings →→→→→Bluetooth →→→→→ Activation. Once Bluetooth is active the sym-bol appears on the radio display. Note: If the radio is turnedoff with the Bluetooth active, at the successive switch on theBluetooth is deactivated.With Bluetooth functionality active select the menu item FindNew from Settings →→→→→ Bluetooth →→→→→ Devices. Once the devicehas been found check if it is "Trusted" or "Untrusted" throughthe menu item Devices List from menu Settings →→→→→Bluetooth →→→→→ Devices, showing the device information. If thedevice is "Untrusted" select OPT from the display showing thedevice information, and then select Service Search.Menu main items NOTE:For what concerns technical characteristics, reference standard,maintenance and troubleshooting, refer to the relevant technical handbook.TETRA Operating modesThe vehicular radio terminal can work in four different TETRAoperating modes, depending on the protocol selected in menuChange Mode: Trunked Mode (TMO), Direct Mode (DMO), Repe-ater Mode (REP), Gateway Mode (GTW).TMODMOREPGTWFM* **Send a statusmessageSend a text mes-sageRead a receivedmessage (Inbox)Access last callslistGo back in a groupcallEnable/Disablethe speechmonitoringfunctionEnable/Disablethe SDSmonitoringfunctionEnable/Disablethe presencesignalVisualizeGPS dataActivate Bluetooth(*)Connect withBluetooth device(*)How to...See the relative accessories user’s guide.Keep pressed the key for a few seconds.PIN insertion at power on, can be:• Enable/disabled from menu• Always enabled• Always disabledIf PIN insertion is enabled, at power on the user must insert thecurrent PIN. In case of insertion of 3 consecutive wrong pin, thecurrent PUK must be inserted to unlock the radio. In case of 3consecutive wrong PUK insertion the radio must be repro-grammed to be unlocked.To adjust the volume of the various sounds access from mainmenu to Settings →→→→→ Preferences →→→→→ Sounds.In the vehicular configuration: to adjust the speech volume,use the volume knob; turn it clockwise to increase the volumeand counterclockwise to decrease it.In the Motorcycle configuration: the triple pushbutton al-lows the same operativity of the knob.(“+” and “-” to increase/decrease the volume;“•” to switch from volume control to group selection function).In the Vehicular configuration: keep pressed the knob untilthe alternate symbols S and appear on the display. Theradio is in group selection mode. Once in this modality turn theknob to choose among the available groups-channel and selectthe group by pressing the knob.In the Motorcycle configuration: the triple pushbutton al-lows the same operativity of the knob.(“+” and “-” to scroll the groups list;“•” to switch from volume control to group selection and toconfirm the choose).Press and then (associated to menu) keys to lock thekeypad; to unlock it press any key and follow the instructionsshown on the display.Keep pressed key for a few seconds. Otherwise selectChange mode from main menu and select the modality.Each WPS is composed of a set of different groups related tothe group selector knob positions. Changing WPS you changethe groups that can be selected by means of the knob. To changeWPS, keep pressed key for a few seconds. Otherwiseselect Settings →→→→→ Group Management →→→→→ WPS Select.Select the group by means of the relevant knob (in the vehicularconfiguration) or the triple push button (in the motorcycle configu-ration), then press PTT to talk; otherwise type in the group addressand press PTT (if the PTT default modality is set (by PRP) forindividual call, press the key before pressing the PTT).Select the group by means of the relevant knob and press thekey . Now by pressing PTT the first available dispatcher ofthe selected group is called (not the gorup). By pressing againthe key and then the PTT the selected group is called.Keep pressed key for a few seconds, then press PTT to talk.Type in the address or select a subscriber from phone bookthen press key .Type in the address or select a subscriber from phone bookthen press PTT (if the PTT default modality is set (by PRP) forgroup call, press the key before pressing the PTT).Keep pressed the emergency key at least for 2 seconds.In TETRA mode the radio can be programmed to: send a callrequest, send an SDS, send a call request and an SDS, at theemergency key pressing.In FM mode, the radio sends an alarm until another radio givesthe received alarm signal throught the key .* * * * *TMODMOREPGTWFM** * * *** *** *** * **Change accesso-ries configurationSwitch on/switchoff the radioManage the PIN(Personal Identifi-cation Number)Adjust theVolumeChange group -channelLock/unlockkeypadChange modalityTMO/DMO/REP/GTW/FM (*)ChangeWorking ProfileSubset (WPS)Call a group /ChannelCall the dispatcherof the selectedgroup (if the net-work allows thisfunction)Call the OPENGROUPMake an individualfull duplex speechcallMake an individualhalf duplex speechcallSend an emer-gency alarm**How to...Once the device is "Trusted" select OPT from the displayshowing the device information, and then select Service List.Choose the service scrolling the list through the keys and, select OPT and then Connect, to connect to the service.To remove a Bluetooth device it is first necessary to discon-nect it closing and removing the relative service:• select Settings →→→→→ Bluetooth →→→→→ Devices →→→→→ DevicesList;• scroll the device list till the device to be removed andselect OPT;• select the item Service List and scroll the Service List tillthe service to be close;• select OPT and then Disconnect. Then, from the samemenu select Remove to remove the service.Now it is possible to remove the device:• select Settings →→→→→ Bluetooth →→→→→ Devices →→→→→ DevicesList;• scroll the device list till the device to be removed andselect OPT;• select the item Remove Device• press the key associated with "YES" to confirm the opera-tion.To deactivate Bluetooth it is first necessary to remove all theBluetooth accessories, then select Settings →→→→→ Bluetooth→→→→→ Deactivation.Access the monitor menu keeping pressed the key for afew seconds from idle status, otherwise select item Monitorfrom main menu. Selecting Opt it is possible to choose among:•Add (to add an user to be monitored);•Delete (to remove an user to be monitored);•View (to visualize the details of the last three radio coveragechecks of the specific user).To make a call in FM mode (whether to a user or to a group)dial the user or the group address to be called, or select theaddress from the Phone lists and press the key . PressPTT to talk.TMODMOREPGTWFM*RemoveBluetooth device(*)DeactivateBluetooth (*)Check thecoverage of otherusersMake a call inFM mode (*)* * * * ** * * * ** * *** * * ** * **** * ** * ** * ** * ***** * ******* *MessagesBy means of this menu it is possible to send text and statusmessages, and to read received messages and sent messages thathave been saved. It is also possible to define the text char size.In Repeater mode with SDS Monitor active it is possible to readthe messages monitored by the radio.Change ModeBy means of this menu item it is possible to select the transmis-sion protocol TMO/DMO/REP/GTW/FM.Encryption (TETRA only)By means of this menu it is possible to enable/disable theencryption function.Phone ListsIn TETRA mode, by means of this menu you can access thephone books (whether user defined or predefined). In FM modeyou can directly access the FM users list.SettingsThrough the sub-menus of this item it is possible to configureseveral options of the radio terminal. For example (in TETRAmode) it is possible to inhibit the transmission (Tx Inhibit), tomanage the working profiles WPS (Group Management), to ac-cess the Bluetooth functionalities.Furthermore through the Preferences menu the user can person-alize the terminal, setting: language, sounds volume, backlight,zoom in/zoom out. It is also possible in REP mode, to enable ordisable the presence signal transmission.In REP or GTW mode it is also possible to enable or disable thespeech monitor function and only in REP mode the SDS monitorfunction. Monitor (FM only) (*)By means of menu Monitor it is possible to check the radiocoverage of other FM radio users. GPSThis menu allows to display the GPS data information. InformationThis menu allows to display the equipment information.HelpSelecting Help from main menu it is possible to visualize thedirect access keys function (direct access keys are available evenduring calls). Within the Help menu are also shown: the descrip-tion of the strings to be dialled to define the call priority, thegateways and the address composition method (for TETRA). It isalso possible to visualize a brief description of the symbols thatcan appear on the display.(*) Function not available for U.S. market

Navigation menu