Scosche BT1200 Bluetooth Carkit User Manual IKQBT1200

Scosche Industries Inc Bluetooth Carkit IKQBT1200

IKQBT1200 User manual

• ElectronicsBox• KeypadControl• Microphone• Power/Speaker/Mute(ISOharness)• Low-levelconnectionharness• Instructionmanual• HardwarebagBEFORE BEGINNINGCheckallvehiclemanufacturercautionsandwarningsregardingelectricalservice(AIRBAGS,ABSBRAKES,ENGINE/BODYCOMPUTERANDBATTERY).PLAN OUT YOUR INSTALLATIONYoushouldpre-determinethelocationofthemicrophone,keypadcontrollerandelectronicsbox.Thiswillsavetimeandeasetheinstallationprocess.USE A VOLT/OHM METER WerecommendtheuseofaVolt/Ohmmetertotestandlocateallconnections.Testlightscouldpossiblydamageavehicle’scomputersystemorcauseanairbagtodeploy.DO NOT ROUTE ANY WIRING THAT MAY BECOME ENTANGLEDwiththebrake/gaspedals,steeringcolumn,oranyothermovingpartsinthevehicle.MICROPHONEForbestperformance,theBT1200microphonemustbepointedtowardthedirectionofthedriver’svoice.Werecommendchoosingalocationbetweentherear-viewmirrorandsunvisor.ThemicrophonecanalsobemountednearthetopoftheA-pillar(windshieldpost).ELECTRONICS BOXMounttheBT1200electronicsboxbehindthestereo.Donotmounttheelectronicsboxnearsourcesofhighheat,moistureormovingparts.HardwareisincludedtoattachtheBT1200boxtothevehicle.KEYPAD CONTROLLERThekeypadisdesignedtoeasilymountinablankswitchplate,dashpanelorcenterconsole.CarefullyINSTALLATION CAUTIONS & WARNINGSMICROPHONEELECTRONICS BOXKEYPAD CONTROLLERBT1200BLUETOOTHTM HANDS-FREE UNIVERSAL CAR KIT ©2010SCOSCHEINDUSTRIES,INC. 300BT120001/10PARTS INCLUDED
123FIGURE 12INSTALLATION OVERVIEWLEGEND:1. Handsfreemicrophone2. Controlkeypad3. ElectronicsboxCALLS HEARD THROUGHFACTORY SPEAKERSIMPORTANT: INSTALL THE ELECTRONICS BOX BEHIND THE GLOVE COMPARTMENT OR BEHIND THE FACTORY RADIO. MAKE ALL PROPER CONNECTIONS AND ROUTE ALL CABLES PRIOR TO HIDING THE ELECTRONICS BOX.
FIGURE 23WIRE CHART (20-pin MOLEX to ISO Power, Mute and Speaker In/Out) LOC. COLOR FUNCTION P1 Brown Negative(-)Muteoutput P2 Black Ground P3 Gray/Black FrontRightNegative(-)speakerinput(Fromcarstereo) P4 Gray FrontRightPositive(+)speakerinput(Tocarstereo) P5 White/Black FrontLeftNegative(-)speakerinput(Tocarstereo) P6 White FrontLeftPositive(+)speakerinput(Tocarstereo) P7 Violet/Black RearRightNegative(-)speakerinput(Tocarstereo) P8 Violet RearRightPositive(+)speakerinput(Tocarstereo) P9 Green/Black RearLeftNegative(-)speakerinput(Tocarstereo) P10 Green RearLeftPositive(+)speakerinput(Tocarstereo) P11 Red +12vSwitchedAccessory(Fused2A) P12 Yellow +12vBatteryConstant(Fused2A) P13 Gray/Black FrontRightNegative(-)speakeroutput(Tocarspeaker) P14 Gray FrontRightPositive(+)speakeroutput(Tocarspeaker) P15 White/Black FrontLeftNegative(-)speakeroutput(Tocarspeaker) P16 White FrontLeftPositive(+)speakeroutput(Tocarspeaker) P17 Violet/Black RearRightNegative(-)speakeroutput(Tocarspeaker) P18 Violet RearRightPositive(+)speakeroutput(Tocarspeaker) P19 Green/Black RearLeftNegative(-)speakeroutput(Tocarspeaker) P20 Green RearLeftPositive(+)speakeroutput(Tocarspeaker)WIRE CHART (8-pin Preamp Line-Level Audio 2CH In/Out) P1 Gray/Black RightChannelNegative(-)output(Tocaramplifier) P2 Gray RightChannelPositive(+)output(Tocaramplifier) P3 White LeftChannelPositive(+)output(Tocaramplifier) P4 White/Black LeftChannelNegative(-)output(Tocaramplifier) P5 Gray/Black RightChannelNegative(-)input(Tocarstereo) P6 Gray RightChannelPositive(+)input(Tocarstereo) P7 White LeftChannelPositive(+)input(Tocarstereo) P8 White/Black LeftChannelNegative(-)input(Tocarstereo)CONNNECTIONS
FIGURE 34INSTALLATIONSTANDARD INSTALLATION UsetheSpeakerInput/Outputconnectionsonthe20-PINSpeaker/Power/MuteISOconnector.NOTE:OptionISO-to-VehiclespecificharnessconnectorkitsareavailabletomaketheBT1200aplugandplayinstallation.TheseharnessconnectorkitssoldseparatelyandnotincludedwiththeBT1200 (See T-Harness section on page 5).1. Locatethe4speakersoutputsofthevehiclesstereo.2. CutandconnectinputwiresoftheBT1200(Pin#3-#10)tothevehicle’sspeakeroutputs comingdirectlyfromthestereoside.3. ConnecttheBT1200speakeroutputwires(Pin#13-#20)totheremainingspeakerleadsthat godirectlytothevehiclesfrontandrearspeakers.OPTIONAL MUTE CONNECTIONTheBT1200providesaNegative(-)Muteoutputforusewithstereo’sthathaveacompatibleNegative(-)“Mute”inputtoattenuatetheAudioduringHands-freekituse.SeetheDIAGRAMfortypicalconnec-tiontypes.TheBROWNMutewireprovidesaNegative(-)outputwhenthereisanactiveincomingoroutgo-ingcall.MUTE FUNCTION (BrownNegativeTriggerWire)TheBT1200supportsmutefunc-tionalityensuringthatthestereowillnotplayaudioduringcellularuse.Ifyou’veinstalledtheBT1200inthestandardmethodusingtheinput/outputspeakerwiresprovided,thenyourstereoshouldautomati-callybemutedbytheBT1200.IfyouhaveaPremiumsoundsystemwithadditionalspeakerslikeoneormoresubwoofers,youmaybeabletoutilizetheNegativeMUTEoutputprovidedbytheBT1200.CheckyourStereo’sdocumentationtodeterminewhetherithasadesignatedNegativeMuteINPUT.Ifthisisthecase,thentaptheBrownwireoftheBT1200totheMUTEwireofyourstereo.DuringphonecallstheBT1200willsendaNegativeGroundsignaltotheBROWNwire.MUTEWIRE
FACTORY AMPINPUTOUTPUTWhite: Audio Left +White/Black: Audio Left -Grey: Audio Right +Grey/Black: Audio Right -White: Audio Left +White/Black: Audio Left -Grey: Audio Right +Grey/Black: Audio Right -FACTORY RADIOFACTORYSPEAKERSBT12008-PIN PRE-AMP LINE LEVELINSTALLATION HARNESSFIGURE 4INSTALLATION (cont’d)5LOW-LEVEL AUDIO INSTALLATION UsetheLine-LevelInput/Outputcon-nectionsonthe8-PINconnector.NOTE:ThisoptionisforusewithexistingFactory-amplifiedsoundsystems.TheBT1200providesa2-channelLow-levelinputoutputswitchingforpre-amplifierinstallation.1. Locatethepre-ampaudiooutputsofthevehiclestereo.2. CutandconnectinputwiresoftheBT12008-Pinharness(Pin#5-#8)tothevehicle’saudiooutputscomingdirectlyfromthestereoside.3. ConnecttheBT1200low-levelout-putwires(Pin#1-#4)totheremainingaudiosignalleadsthatgodirectlytothevehicle’samplifier.“T”-HARNESS ACCESSORY(Soldseparately)TosimplifyBT1200installation,vehiclespecificT-HarnessesareavailabletoadapttheBT1200ISOconnectorstoyourvehicle’sFactorywireharnessconnectors.T-harnessallowsyoutoeas-ilyinstalltheBT1200systeminyourvehiclewithouttheneedforcuttingandsplicingwiring.THarnessesaresoldseparatelyandavailableformostpopularvehiclemakesandmodelsincludingGM,Ford,Chrysler,Toyota,Honda,Nissanandmore.CallScosche(800)621-3695orgotowww.scosche.comtofindtherightharnessforyourvehicle.TO RADIOTO VEHICLET-HARNESS(Sold separately)BT1200HARNESSFUSE FUSE
DRILL HOLE PRECISELYFOR BEST FIT.FIGURE 6or other at surface6INSTALLATION (cont’d)KEYPAD CONTROLLER INSTALLATION STEPSTheBT1200keypadcontrollerisdesignedtoeasilymountinablankswitchplate,dashpanelorcenterconsole.Carefullychoosealocationthatiswithineasyreachofthedriver.Drillingisrequiredtomountthekeypad.Checkforclearanceorobstructionsbehindtheswitchlocationtoensuretherearenovitalvehiclecomponentsorwiringthatmightbecomedamagedbeforedrilling!Whenchoosingalocation,considerthe10ft.(3m)lengthofthecontrollercable.1. Usea9/16''(15mm)drillforthekeypadcontroller.Drillaholeinthechosenlocation. Thecontrollerkeypadisdesignedtolockitselfintoaproperlydrilledmountinghole.2. Cleanthemountingsurfaceofdirtorgreasebeforemountingthecontroller.3. Feedcablethroughthehole,peelthebackingpaperfromthecontrollerandpressthe controllerintoplace.MICROPHONE INSTALLATION STEPSForbestperformance,theBT1200microphonemustbepointedtowardthedirectionofthedriver’svoice.Werecommendchoosingalocationbetweentherear-viewmirrorandsunvisor(seeFig.1,page2).Whenchoosingalocation,considerthe10ft.(3m)lengthofthemicrophonecable.Forbestresults,themountingsurfaceshouldbeflatandpreferablysmooth.Themicrophoneholderhasaself-adhesivestripontheback.1. Separatethemicfromitsholder(gentlypullapart)2. Cleanthemountingsurfaceofdirtorgreasebeforemountingthemicholder.3. Peelthebackingpaperfromtheadhesivestripandpressthemicholderontothemounting surfaceandholdfor30seconds.4. Pushthemicbackontotheroundpegandpoint(aim)towardsthedriver’sseat.
FIGURE 77OPERATIONEASY PAIRINGNote:TheBT1200mustbepairedwithyourmobilephonebeforeuse.TheBT1200includesan“Easy”pairingfeaturethatwillautomaticallyre-connectittothemostrecentlypaireddevice.Ifthemostrecentdeviceisnotpresentwithin10seconds,thentheBT1200willAUTOMATICALLYgointopairingmodeandyouwillheartheannouncement”Poweron”followedbytheannouncement“Pairingphone,pleaseplaceyourphoneinpairingmodeandenterPINcode0000”.TheblueLEDwithflashevery(1)second.MANUAL PAIRING1.PowerofftheBT1200.2.PressandholdtheMulti-FunctionButton[MFB]for6secondsuntilyouhearthe announcement“Pairingphone-pleaseputyourphoneinpairingmodeandenterPINcode “0000”.TheblueLEDwillflasheverysecond.3.ActivatetheBluetoothfeaturefromyourphone’smenu.ThephonewillsearchallBluetooth deviceswithin10meters(30ft.)anddisplaythemasalist.4.Select“BT1200”fromthelist.Enter“0000”topairandconnecttheBT1200toyourphone.If youareusinganAppleiPhone,youcanjusthit“OK”topairtotheBT1200.5.TheblueLEDwillblinkwhenbothdevicesaresuccessfullypaired,andyouwillheartheBT1200announce:“Pairingsuccessful”.Note:Ifthepairingcannotbecompletedwith2 minutesofpairingmodeactivationtheBT1200willpowerdown.TheBT1200willannounce “Pairingfailed-pleaseputyourphoneinpairingmodeandtryagain.”Pleaserepeatsteps1 through4.POWERING ON/OFFThe BT1200 will switch onautomaticallywhenyouturnONtheIgnitionkey.Youwillhearthesystemspeak:  “Power on”andthe Blue LED indicator in thecenterbuttonwillbegintoflash.To turn off the Car kit, it willturn off automatically when theignitionisoff.TomanuallypowerofftheBT1200presstheMulti-function button continuously for10 Seconds.  You will hear thesystemspeak:“Poweroff”.TomanuallyturnONtheBT1200presstheMFBfor3seconds.
OPERATION (cont’d)8CONNECTIONIftheBT1200andthemobilephonearedisconnected,theconnectionmayberestoredbythefollowing:1. IftheBT1200hasbeenswitchedoff,turnonpowerandtheconnectionwillberestored automaticallyifsetasatrusteddeviceonyourmobilephone.2. Ifthemobilephonehasbeenswitchedoff,turnonthemobilephoneandrestorethe connectioneitherthroughthephone’smenuorbypressingtheMulti-FunctionButton[MFB]once.3. IftheBT1200andphoneareoutofrange,makesurethedevicesarewithinworkingrange (30Feet/10Meters)andpresstheMulti-FunctionButton[MFB]once.Note:Oncethe connectionissuccessfultheBT1200willannounce“Phoneisreadyforuse,”andtheblue LEDwillflashonceevery3seconds.Thisisknownas“STANDBYMODE”.DISCONNECTIONIftheBT1200needstobedisconnectedfromthephoneconnection(Example:Toconnectyourphonetoanotherdevice)thephonemaybedisconnectedusinganyofthefollowing:1.TurnofftheBT1200orvehicle.2.DisconnecttheBT1200usingthephone’sBluetoothmenu.Note:OncedisconnectissuccessfultheBT1200willannounce“Disconnectcomplete.”TheBT1200willautomaticallyshutoffafterbeingdisconnectedfromapaireddeviceformorethan10minutes.PLACING CALLSYoucaninitiatecallsfromyourmobilephone,ordirectlyfromyourBT1200Carkitusingvoicedialingcommands(ifthisfeatureissupportedbyyourmobilephone)Makingcallsusingvoicedialing:Ifyourmobilehandsetisvoicedialingenabled,pressandholdthe“FWD[Rightdirectionalsymbol]”buttononthecontrollerfor3seconds.Youhearabeep,saythevoicetag.IMPORTANT:Pleasemakesuretorecordvoicetagintothemobilehandsetbeforeusingvoicedialingfunction.ThisfunctionisonlyapplicabletomobilehandsetswithBluetoothHands-FreeProfileANDVoiceDialingcapability.VoicedialingTAGSarestoredonyourphoneandNOTbytheBT1200system.Functionalityvariesdependingonthemobilehandsetmodelsyouhave.Pleaserefertoyourmobilehandsetuserguideforadditionalinformation.Scoschehighlyrecommendsusingthevoicedialfeature(ifyourphoneisequipped)toreducehandsetusewhiledriving.Insomestateshandsetusagewhiledrivingisillegal.(Checkyourlocalorstatemotorvehiclecode)CALLING FROM YOUR MOBILE PHONEDialdirectlyfromyourmobilephone.ThecallisautomaticallyconnectedtotheBT1200handsfreekit.RECEIVING CALLSUponanincomingcall,youwillhearthecallerIDinformationannouncedthroughyourcarstereosystem:”Callfrom(NameorDigits)”;pressthe“FWD[Rightdirectionalsymbol]”buttonontheCarkittoanswerthecall.ENDING CALLSDuringthecall,pressthe“BACK[Leftdirectionalsymbol]”buttonendthecall.YouwillheartheBT1200systemannounce:”Endcall”.REJECTING CALLSUponanincomingcall,pressthe“BACK[Leftdirectionalsymbol]”buttontorejectthecallandsendtoyourphone’svoicemail.TheBT1200systemwillannounce:”Rejectcallsuccessful”.LAST NUMBER RE-DIALINGPresstheMulti-FunctionButton[MFB]twicetoredialthelastnumber;TheBT1200systemwillannounce:“Redialing”.
9OPERATION (cont’d)ADJUSTING CURRENT CALL VOLUMEToincreasethevolumeduringthecall,pressthe“+”buttontoincreasevolumebyonelevel,repeatthisprocedureuntilyouhavereachedthedesiredlevel.Todecreasethevolumeduringthecall,Press“-”buttontodecreasethevolumebyonelevel,repeatthisprocedureuntilyouhavereachedthedesiredlevel.MUTE MICROPHONEDuringacall,pressandholdthe“BACK[Leftdirectionalsymbol]”buttonfor3secondstomutethemicrophone.Pressandholdthe“BACK[Leftdirectionalsymbol]”buttonAGAINfor3secondstoturntheMICbackON.ANSWER or REJECT SECOND CALLSToanswerasecondincomingcall:Duringacall,whenanothercalloccurs,shortpressthe“FWD”[Rightdirectionalsymbol]buttontopickupthecallandthefirstcallwillbeplacedonhold.Torejectasecondincomingcall:Duringacall,whenanothercalloccurs,shortpressthe“BACK[Leftdirectionalsymbol]”buttontorejectthecallandsendittoyourphone’svoicemail.SWAPPING CALLSDuringaThree-waycall(youandtwoothers),pressthe“FWD”[Rightdirectionalsymbol]for3secstoswapthecallDuringaThree-waycall,shortpressthe“BACK[Leftdirectionalsymbol]”buttontoendthecur-rentcallandanothercallwillbeactiveautomaticallyTRANSFERRING CALLSHandsfreekittoMobilePhone:Duringacall,presstheMulti-FunctionButton[MFB]twice,andthecallisroutedtoyourmobilephone.MobilePhonetoHandsfreekit:Pressthe“Multi-FunctionButton[MFB]”buttononcetoroutethecalltotheBT1200handsfreekit.TEXT-TO-SPEECH (Voice Announce) LANGUAGEWhileNOTonaphonecall,pressandholdthe“+”buttonfor3secondsandtheHandsfreekitannounces“SelectLanguage”.Repeattheprocesstoselectthedesiredlanguageinthefollow-ingorderofEnglish,French,Italian,GermanandSpanish.ADJUSTING TEXT-TO-SPEECH (Voice Announce) VOLUMEToincreasethevolume(Notduringaphonecall),Pressthe“+”buttontoincreaseText-To-Speechvoicevolumeyouwillhear“Activated“.Todecreasethevolumepressthe“-”buttontodecreaseText-To-Speechvoicevolumeyouwillehear“Activated“.Theword“Activated”meansnothing.Itisjustanannouncementprovidedtodeterminethevolumeoutput.TURNING ON/OFF TEXT-TO-SPEECH (Voice Announce)Pressandholdthe“+”for6seconds(notduringaphonecall).“VoicePromptOn”or“VoicePromptOff”isannouncedtodenotethecurrentstatus.TRANSFERRING MOBILE PHONEBOOK TO HANDSFREE KITMakesuretohaveyourphoneconnectedtotheBT1200systembeforethisoperation.1. Pressthe“-”buttonfor3secondsandtheBlueLEDlightindicatorcomeson.TheBT1200systemwillannounce”Loadingphonebook.Pleasewait”,whenitbeginstoreceivephonebookinformationfromyourphone.2. Icantakesometimetoloadyourphonescontacts.DuringtheprocesstheBT1200willan-nounce:“Pleasewait”every30seconds.3. Whentheprocessiscompleted,theBT1200systemsannounces“ContactsSaved”andstatesthenumberofcontactsreceivedfromyourmobilephonememoryorSIMmemory.
10OPERATION (cont’d)IMPORTANT PHONEBOOK NOTES: The BT1200 can store up to 1000 contacts ONLY. When/if the memory is full, the system will announce: ”Phonebook is full”. If there is a failure during the process, the car kit will announce: ”Loading phonebook failed”. Please check your phone to find out if it has phonebook support or the ability to allow your contacts to be “pulled” from another Bluetooth device. The BT1200 system may NOT be compatible with your particular phonebook due to the wide range of contact and object profiles available in today’s mobile device market. DELETE CURRENT PHONEBOOKThe BT1200 does NOT support multiple phonebooks from more than one mobile phone. You may therefore choose to delete the current phonebook so that another mobile phone’s can connected to upload its phonebook. To Remove Phonebook Entries (not during a phone call), press “-”buttons for 6 seconds. The system will announce: “Phonebook Deleted”.Entire phonebook memory in the BT1200 will be deleted.RESTORE FACTORY DEFAULT SETTINGSLISTENING TO MUSICWIRELESS MUSIC (With supported A2DP/AVRCP devices)Listen to music from your mobile phone and/or other Bluetooth device is easy using the BT1200. Read the following notes to become more familiar with how your BT1200 system integrates between wireless music and phone operation. 3.5MM AUX INPUTYou can also listen to music via a wired connection from any portable device that has a standard 3.5mm headphone jack. (3.5mm cable is not included with BT1200) Note that a cable must be run from the BT1200 electronics box to a conveniently accessible location in your vehicle.A2DP/AVRCP NOTES:If your phone is paired to the BT1200 and supports BOTH Hands free HFP and Streaming Audio A2DP then playing music and handling call should operate seamlessly. If you choose to have a second separate A2DP device transmit audio to the BT1200, it must be paired separately. In the case of a second device for wireless audio, make sure your phone is not currently paired to the BT1200’s A2DP profile otherwise you will not hear music from the secondary device.CALLS DURING MUSICTo answer an incoming call while the music is playing press the “FWD” [Right directional symbol] to answer. Music is muted until you end the call.PLAY/PAUSE MUSICPress the Multi-Function Button [MFB] to Play or Pause music playingTRACK FF/RRTo track Forward Press the “FWD” [Right directional symbol] button to the next track (or tracks).To track Backward Press the “BACK” [Left directional symbol] button to the previous track (or tracks).ADJUSTING MUSIC VOLUMETo increase volume (during music play), Press the “+” button to increase until desired level. To decrease volume (during music play), Press the “-” button to decrease until desired level. To restore your Car kit to its original settings, press and hold “V-” button for 10 seconds until the blue LED light indication flashes rapidly. the Car kit will power off automatically. This process is complete when Car kit announces “Set Factory Default Complete”.
11LISTENING TO MUSIC (cont’d)LISTENING TO MUSIC FROM EXTERNAL AUDIO DEVICEConnectthe3.5mmjacktoyouraudiodeviceandtheBT1200electronicsbox.Pressandhold“BACK”[Leftdirectionalbutton]for3secondstoswitchon“Linein”function.ARedLEDwillilluminatefromtheBT1200controllerindicatingthatit’sin“Linein”mode.IfyoureceiveanincomingcallwhilelisteningtotheLineinsource,pressthe“FWD[Rightdirectionalsymbol]”toanswerthecall.Musicismuteduntilyouendthecall.Pressandholdthe“BACK”[Leftdirectionalsymbol]button3secondsagaintoswitchoffLineinfunction.TheRedLEDwillturnoff.WIRELESS MUSIC (With supported A2DP/AVRCP devices)Listentomusicfromyourmobilephoneand/orotherBluetoothdeviceiseasyusingtheBT1200.ReadthefollowingnotestobecomemorefamiliarwithhowyourBT1200systemintegratesbetweenwirelessmusicandphoneoperation.3.5MM AUX INPUTYoucanalsolistentomusicviaawiredconnectionfromanyportabledevicethathasastandard3.5mmheadphonejack.(3.5mmcableisnotincludedwithBT1200)NotethatacablemustberunfromtheBT1200electronicsboxtoaconvenientlyaccessiblelocationinyourvehicle.A2DP/AVRCP NOTES:IfyourphoneispairedtotheBT1200andsupportsBOTHHandsfreeHFPandStreamingAudioA2DPthenplayingmusicandhandlingcallshouldoperateseamlessly.IfyouchoosetohaveasecondseparateA2DPdevicetransmitaudiototheBT1200,itmustbepairedseparately.Inthecaseofaseconddeviceforwirelessaudio,makesureyourphoneisnotcurrentlypairedtotheBT1200’sA2DPprofileotherwiseyouwillnothearmusicfromthesecondarydevice.CALLS DURING MUSICToansweranincomingcallwhilethemusicisplayingpressthe“FWD”[Rightdirectionalsymbol]toanswer.Musicismuteduntilyouendthecall.PLAY/PAUSE MUSICPresstheMulti-FunctionButton[MFB]toPlayorPausemusicplaying.TRACK FF/RRTotrackForwardPressthe“FWD”[Rightdirectionalsymbol]buttontothenexttrack(ortracks).TotrackBackwardPressthe“BACK”[Leftdirectionalsymbol]buttontotheprevioustrack(ortracks).ADJUSTING MUSIC VOLUMEToincreasevolume(duringmusicplay),Pressthe“+”buttontoincreaseuntildesiredlevel.Todecreasevolume(duringmusicplay),Pressthe“-”buttontodecreaseuntildesiredlevel.
Scosche Industries Inc. warrants this product to be free from defects in material and workmanship for a period of 90 days from purchase. This Scosche product is sold with the understanding that the purchaser has independently determined the suitability of this product. This warranty is offered to the original purchaser of the product only. This warranty does not cover the product if physically damaged, subject to negligence or misuse, abuse, alteration, accident, or an act of GOD. This warranty does not apply to product which has water or physically damaged by accident or which has been misused, disassembled or altered.The original dated sales slip or proof of purchase will establish warranty eligibility. If the product should prove defective within the warranty period, return the product with proof of purchase to Scosche Industries Inc. Scosche, at its option, will replace or repair the product free of charge and return the product postage paid. In no event shall Scosche Industries, Inc. be responsible for claims beyond the replacement value of the defective product, or in any way be liable or responsible for consequential or incidental damages. No express warranties and no implied warranties, whether for fitness or any particular use or otherwise, except as set forth above (which is made expressly in lieu of all other warranties) shall apply to products sold by Scosche. Scosche Industries cannot be held responsible for discrepancies/inconsistencies that may occur due to automotive manufacturing changes or option.LIMITED WARRANTYFCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Any changes or modification not expressly approved by the party responsible could void the user’s authority to operate the device.This Category II radio communication device complies with Industry Canada Standard RSS-310 for RX Siren.This device complies with part 15 of the FCC Rules and RSS-210 for TX remote control. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.To comply with FCC RF exposure requirements, the device and the antenna for this device must be installed to ensure a minimum separation distance of 20 cm or more from a person's body. Other operating configurations should be avoided.12FCC ID: IKQBT1200changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.To comply with FCC RF exposure requirements, the device and the antenna for this device must be installed to ensure a minimum separation distance of 20 cm or more from a person's body. Other operating configurations should be avoided.

Navigation menu