Scosche BT102 Wireless Earbuds User Manual User manual

Scosche Industries Inc Wireless Earbuds User manual

User_manual

USER MANUAL Package contains a. Bluetooth/wireless headsetb. USB charging cablec. Replacement ear tipsd. User manualBT102 Wireless Earbuds
Control 1. Multifunctional Button(MFB)Answer/hang up/reject / redial, play/pause music, power on/off2.”+” Next song/Volume up“+” 3.”- “Previous song/Volume down“-” 4. Micro USB charging portMicro USBTurn on/off and reconnect 1. When the headset is power off, press the (MFB) key for about3-4 seconds until the blue and red light flash alternately. (Voice:The Bluetooth device is ready to pair). The Bluetooth headsetwill automatically connect to the device connected last timeafter you turn on the headset. ( Blue light flashes 1 time persecond).2. When the power is on, press and hold the (MFB) key 5-6seconds until the red light flash 1 second. (Voice: Power off)Pair the headset with a compatible phone 1. When the headset is power off, press the (MFB) key for about
3-4 seconds until the blue and red light flash alternately. (Voice:The Bluetooth device is ready to pair)2. Set the cell phone to search for Bluetooth devices, connect“Scosche BT102” device.3. If the pairing is successful, the headset’s blue light will flashevery 1 second. (Voice: Bluetooth connected)4. If pass code is requested by the cell phone, enter 0000 oncethe headset has paired with your device.Volume control Adjust volume: Momentarily press the “+” key to increase volume and momentarily press the “-” key to decrease volume. (When the volume is maximum or minimum, the headset will beep twice) Music control 1. Next song: press and hold the “+” key.2. Previous song: press and hold the “-” key3. Play/pause music: Momentarily press the (MFB) key while themusic is playing1.Answer/hang up/reject/redial a call 1. To answer or hang up a call: Press the (MFB) key, or use the
phone keys.(music will automatically pause during phone call)2. To reject a call: Press the (MFB) button twice quickly, or usethe phone keys.3. To redial the last phone number dialed out: Press the (MFB)button twice quickly.Charge the battery This headset has an internal rechargeable battery 1. When the battery low the red light flashes 1 time every 3seconds. 2. Connect the charging cable to the Micro USB charging porton the headset.3. Connect the headset cable to a USB power source. The redlight will be on during charging. If charging does not start,disconnect the charger, plug it in again, and retry. Charging thebattery fully may take up to 2~3 hours.4. When the battery is fully charged, the red light will turn blue.Disconnect the charger from the USB power source and theheadset.5. If the headset has not been used for a long time, you will needto charge it for about 30 minutes (the red light flashes 1 time persecond), then the red light will be on to indicate charging.
FCC StatementChanges or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-- Reorient or relocate the receiving antenna.-- Increase the separation between the equipment and receiver.-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.-- Consult the dealer or an experienced radio/TV technician for helpThis device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.IC StatementThis device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.Le présent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage,et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement

Navigation menu