Scanreco G5CUR 2.4 GHz Transceiver User Manual

Scanreco AB 2.4 GHz Transceiver

User Manual

Instruction Manual66063 AEnglishDocument Revision LanguageG5 CU R
Attribute InformationDocument Type Instruction ManualTitle SCANRECO G5 CU RDocument No. 66063Language EnglishRelease date 2013-05-20Original EnglishRelease date (original) 2013-05-20Author SCANRECOCompany SCANRECO AB, SWEDENRevision Date NoteA 2013-05-20 First releaseDocument informationRevision historyAll rights reservedDesign, equipment, technical data and specications are subject to change or improvement without prior notice. The text in this instruction manual, or any part of it may not be reproduced or transmitted in any form or by any means, including electronic, mechanical, photocopying, recording, storage in an information retrieval system, or otherwise, without prior written permis-sion of SCANRECO AB, SWEDEN.Document type Document number PageRevInstruction Manual 66063 A2 of 8
G5 receiver Product description The Central Unit (CU) is manufactured in robust plastic housing and provides contacts for the connection of power supply and electro-hydraulic valves. Several of the outputs can also be used as digital inputs. Depending on the version of the G5 Central unit, it can either be equipped with MOSFET outputs and Deutsch connectors or can have relay outputs with terminal block.Since the central unit can be exposed to very tough environments, the box is encapsulated to give protection from damp, heat, cold, dust, vibration and corrosive environments.The Central unit has short circuit protected inputs and outputs and has protection against reverse polarity, over-voltage, large incoming voltage transients and EMC/RF.Label Relay output The Relay output connectors are separated from the rest of the electronics in thecentral unit to create an electrically isolated output. The maximum load for eachoutput is 10A. Through the terminal block, both the normally open and the normallyclosed connection points are available.Document type Document number PageRevInstruction Manual 66063 A3 of 8
171511 Terminal schematics G5 CU R5 and G5 CU R10 ATTENTION!After assembly make sure you tighten the housing screws with 0,8 Nm to avoid any water ingress.The main board may be used stand alone or together with one expansion board.There are several different expansion boards.All expansions boards have the same mechanical outline. They may have different funcionalities depending on customers application.The differnt functions are exemplied in the table below:Expansion boardsModels1 = GND2 = Power Supply +3 = REL1, common4 = REL1, normally closed5 = REL1, normally open6 = REL2, common7 = REL2, normally closed8 = REL2, normally open9 = REL3, common10 = REL3, normally closed11 = REL3, normally open12 = REL4, common13 = REL4, normally closed14 = REL4, normally open15 = REL5, common16 = REL5, normally closed17 = REL5, normally open1 = REL6, common2 = REL6, normally closed3 = REL6, normally open4 = REL7, common5 = REL7, normally closed6 = REL7, normally open7 = REL8, common8 = REL8, normally closed9 = REL8, normally open10 = REL9, common11 = REL9, normally closed12 = REL9, normally open13 = REL10, common14 = REL10, normally closed15 = REL10, normally openDocument type Document number PageRevExpansion board (49839)Main boardDescription of expansion functions Number of exspansion functionRelays 1-5Analog inputs 1-10Analog outputs 1-5Digital I/O 1-20PWM 1-5Model FunctionsG5CU R5 Two cable glands. 5 Relay outputs.G5CU R10 Two cable glands. 10 Relay outputs.Instruction Manual 66063 A4 of 8
127mm57mm186mm117mmSize: approx. ~ 127 x 117 x 57 mm / ~ 5,0 x 4,6 x 2,2 in. Technical Data Central Unit Attribute InformationHousing material Plastic PCIP-class IP67 (for versions with cable glands IP65)Ambient temperature -25˚C to +70˚CSupply voltage 9-36VDCFuse Not required.Current consumption at idle <30mARelay Output load Max 10 AHousing screw torque 0,8 NmWeight Approx. 0,35KgDocument type Document number PageRevInstruction Manual 66063 A5 of 8
Attribute InformationFrequency 2,400 - 2,4835 GHzChannels managementFHSSDSSSTHSSChannel order PseudorandomChannel capacityDuplexSystem address/ID<16777216 unique system addresses availableRedundancy CRC-16Range 100 meters Technical information The G5 system family incorporates an automated frequency jumping technology, a reliable radio transmission highly resistant to interference.The radio transmission takes place within the ISM-band used at pre-dened channels.The channel switching takes place multiple times per second following a pseudorandom se-quence. This ensures that transmission takes place on an optimal frequency at all times!No transmitter uses the same pseudorandom sequence order when switching channels; this minimizes the risk of two G5 systems interfering with each other.The G5 Pocket is approved to transmit on the ISM band. The radio is license free for the end user. Radio informationDocument type Document number PageRevInstruction Manual 66063 A6 of 8
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.CAN ICES-3 (A)/NMB-3(A)The antenna(s) used for this transmitter must be installed to provide a separationdistance of at least 20 cm from all persons and must not be co-located or operatingin conjunction with any other antenna or transmitter.L’antenne (s) utiliseé pour cet émetteur doit être installé pour fournir une distance de séparation d’au moins 20 cm de toute personne et ne doit pas être co-localisées ou opérant en conjonction avec une autre antenne ou émetteur.Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.Warning FCC information Industry Canada Information Document type Document number PageRevInstruction Manual 66063 A7 of 8

Navigation menu