Satellite Electronic 18003 CEILING FAN REMOTE CONTROLLER User Manual TR256A MR181A AC120V FCC

Satellite Electronic(Zhong Shan)Ltd. CEILING FAN REMOTE CONTROLLER TR256A MR181A AC120V FCC

User Manual

CEILING FAN REMOTE CONTROLLEROPERATION AND INSTALLATION INSTRUCTIONS(Please keep this instruction pamphlet.)IMPORTANT POINTS TO REMEMBER:1. Read and save these instructions.2. Please note that all fixed wiring appliances should be installed by a qualified electrician.3. The supply to the remote control receiver should be connected through a mains switch, i.e.existing wall switch.4. Disconnect from power supply at wall switch before working on remote control receiver orceiling fan.5. Install receiver into the ceiling fan canopy of the fan to ensure proper protection.6. This unit is to be used for the control of ceiling fan and in an AC110V/120V 60Hz powersupply only.7. Do not install in damp locations or immerse into water. (For indoor use only.)8. Do not pull on or cut leads shorter.9. Do not drop or bump the unit.10. PLEASE NOTE: The battery will weaken with age and should be replaced before leakingtakes place as this will damage the transmitter. Dispose of used battery properly, keep thebattery out of reach of children.11. CAUTION: To reduce the risk of fire or injury, do not use this product in conjunction with anyvariable (rheostat) wall control.INSTALLATION INSTRUCTIONS1. Ceiling fan must be set at HIGH speed and light kit (If any) at ON position by pulling the“Pull Switch” after installation.2. Once the connection has been made, the receiver inserts into the drop rod hanging bracket.The canopy comes up to cover the receiver and bracket.IMPORTANTYOU MUST SET CEILING FAN MANUAL SWITCH TO HIGH SPEED AND LIGHTKIT (IF ANY) TO ON POSITION BEFORE OPERATING REMOTE CONTROL.CAUTION: INCORRECT WIRE CONNECTION WOULD DAMAGE THIS RECEIVER.
LEARNING PROCESS1. After installing the unit and power on, open battery cover (withbatteriy, DC3V/CR20321pc, installed), press remote’s LEARNkey to control ceiling fan for learning process. Please note thatpress any button within 1 minute after power on. If just replacebatteries, no need to re-learn.2. Please note that the transmitter can learn in multiple receiver,when doing learning process please make sure not learn in otherreceiver.CHANNELSETTING0: All handsets and receivers are factory pre-set to the same channel. You can operate the fan withoutdoing a channel setting above but we recommend that you set an individual channel for your fan.1: This is to allow for each handset and receiver to be set on an individual channel.LIGHT FUNCTION SELECT SWITCHIf installed energy light onto ceiling fan, please set the “light function select switch” “light function select switch” toon/off position,” O”. If installed tungsten light onto ceiling fan, please set the “light function select switch” to dimmerposition,” D”.FUNCTIONS OF TRANSMITTER:Turn on the fan at high speed: Turn on the fan at medium speed: Turn on the fan at low speed: Turn off the ceiling fan.:ON/OFF- Press and release immediately to turn on or off the lightDIMMER- Press and hold on to dimmer or brighten the light. (For the tungsten bulb and “light function selectswitch” is at D position.)To assure continued FCC compliance:FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna. --Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consultthe dealer or an experienced radio/TV technician for help.Installation of transmitter wallmount holder with two screws.
To assure continued FCC compliance:Any changes or modifications not expressly approved by the grantee of this device could void the user's authorityto operate the equipment.FCC ID：2AQZU-18003This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) Thisdevice may not cause harmful interference, and (2) this device must accept any interference received, includinginterference that may cause undesired operation.

Navigation menu