STEELMATE BRM047 Parking Assist System User Manual

STEELMATE CO., LTD. Parking Assist System Users Manual

Users Manual

PRI0023/ARegistration DetailsThis form must be filled in, kept handy and producedwith any warranty claim, together with the purchaseinvoice and/or receipt.Think about safety Think Steel mateMODEL : PTS400QPARKING ASSISTANT SYSTEMMANUFACTURED BY:Steelmate Co., Ltd.http: //www.globalsources.com/steelmate.coE-mail: steelmate@globalsources.com sales@steel-mate.comManualISO 9001 : 2000Certiticate : 04111 2003 1786ISO / TS 16949 : 2002Certiticate : 04111 2003 1786Name:Address:Authorized Dealer:Purchase Date:Vehicle Type:Registration No:Installers' Name:Product Type:Model No:< 0.4m, Zone 5 (Red LED)0.4~0.6m, Zone 4 (Red LED)0.6~0.8m, Zone 3 (Orange LED)0.8~1.0m, Zone 2 (Orange LED)1.0~1.7m, Zone 1 (Green LED)The Digital Matrix LED Display:example 2example 1 example 3AttentionsMisleading detection may occour due to the following cases:Smooth sloping surface Smooth round object Items absorbing sound,e.g.cotton1.Heavy raln,dirty or damaged sensor could result in mlsleading detection.2.Check if the system is in order before use.3.Please replace the damaged sensor when the system detects it.4.The product is a driver assistant device. No warranty as to operating efficiency and accident is guaranteed. It is not a substitute for the driver's responsibility when driving a vehicle.5.Do not paint over the sensors as this will affect the performance.29Volume switchThe digital numberon display will showevery 0.1M changeof distanceDigital Number Display + Audio WarningAudio warning Distance on display LED matrix display4Mount the display on thedashboard firmly for the drivereasy to see.Clean the dash board for moutingthe display.Take off the 3M sticker of thedisplay.Display Installation7blackwhiteGND2PReversing power(+)Zone 1Zone 2Zone 3Zone 4Zone 5Zone 5
The parking assistant system is an ultrasonic distancemonitoring system. It electronically detects the areabehind your vehicle during reversing, and alerts youwith audible tone and digital display if there is anobject behind your car.Every piece of our products has passed the moststringent test before releasing to the market. It isreliable at a wide temperature range ( -40ûC ~ +80ûC)and becomes very useful when you are reversingat a raining day, snowing day or at night etc. Withthe help of Steelmate parking assistant system, youcan enjoy a convenient and nervous - free reversing.Features:1. Detection distance: 0.30 ~ 1.79 m2. No wire from ECU to display3. Self-test function activated by reverse gear4. 3 Colour matrix LED display shows the object's location5. Anti-false alert technology6. All weather design (-40ûC ~ +80ûC)7. Easy installation8. Volume controlSpecifications:a) Voltage: 12 V*3Vb) ECU working current: 35mA*5mAc) Display working current: < 270mAd) Buzzer: 70 ~ 90dBPossible Causes And SolutionsI. The unit is warranted for a limited period fromthe date of purchase. In the event of any defectarising in the unit when you use it as per theinstructions during the warranty period, the repairwould be carried out free.* It is required to show this Warranty Card when have the unit repaired.* The model and series number on unit must be the same as the information in the Warranty Card.II. This warranty is non-transferable and is automatically void if:* The original purchaser has not completed the warranty card* The unit's serial number is defaced, missing or altered* The unit has been modified or used in a manner contrary to its intended purpose* The unit has been damaged by accident, unreasonable use, neglect, improper service and installation.III. The warranty does not cover damage to the unit caused by installation or removal of the unit.Warranty101About Parking Assistant System (PTS)Important NoticeThis parking assistant system is designed as a reversingaid. It is not a substitute of driver's responsibilities normallyassumed when reversing. Steelmate does not liable for anydamages caused by reversing only rely on this system. Proper driving skills, such as slow down, use of mirror or lookout etc.is always essential.1. This unit is for vehicles with 12v DC only2. It should be installed by a professional3. Avoid high temperature and high voltage while laying out the wire harness4. Wire connection point should be insulated5. Conduct test after finishing the installation1. No beep at power up or no LED light falshing1).Is power wire connected to ECU correctly?2).Verify the ground connection3).Have you connected theÊcorrect reversing light wire?Ê2. False warning tone or false LED falshing1).Is sensor mounted too low or pointing to the ground?Ê3.Sensors do not detect any objects1).Are sensors properly plugged into the correct sockets?ÊIf the problem persists, please follow these steps:A. For consumers: Contact your dealer or nearby steelmate service centerB. For Installer or dealer:1).Replace the ECU and re-check the system2).Test the sensors withÊcertified ECU and using a flat wooden board3).Plug the certified sensors into the ECU and re-check4).Email your questions and we will reply ASAP.ÊMore tech tips are available on our website: www.steel-mate.comThe system will test all the sensors when thereversing gear is engaged.If all the sensors are normal, the system will beeponce and the LED display will flash once.If there is any problem with the sensors, the systemwill beep three times to indicate that one or moresensors have problems.Self-test FunctionThe flashing LED indicates the problem sensorThe total number of the problem sensorsSensor A has problem (E1: 1 problem sensor)Sensor A,D have problem (E2: 2 problem sensors)*Check the problem sensor or replace the damaged sensor.The system will test all the sensors when thereversing gear is engaged, and then the systemdetects objects.a) The object distance is: >1.8m:b) The object distance is: 1.7~0.3m:The display will show the distance by digitalnumber and show the object's location in thematrix LED display.c) The object distance is: <0.3m:"-P" will be shown and "Stop" will flash on thedisplayHow Does The System WorkZone 1 green LED of display will flash3Function Test After Installation1.7mTesting the system features with a wooden plate (20cm wide x 100cm height)after the installation.8Installation Diagram512~20cm 12~20cm50~70cm0.3L 0.4L 0.3LHow To Install The SensorMount ECU in trunkConnect the red wireto reversing light(+)ECU Installationsensor Asensor Bsensor Csensor D reversing lingt(+)GNDredblack6DisplayConnect toreversing light(+)ECUConnect toreversing light(+)ECU1. Check the size of the holesaw to be compatible to thediameter of the sensor.UPUP2. Install the sensor vertically,the "up" sign must be onupside.Caution:Changes or modifications to this unit not expressly approved by the party responsible for compliance will void the user's authority to operate the equipment. Any change to the equipment will void FCC grant.NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:--Reorient or relocate the receiving antenna.--Increase the separation between the equipment and receiver.--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.--Consult the dealer or an experienced radio/TV technician for help.--This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Navigation menu