SEGI J2W8000R Two-Way FM Remote User Manual 2w8000FMR FCC ID

SEGI LIMITED Two-Way FM Remote 2w8000FMR FCC ID

Manual

By Firstech, LLC.www.compustar.comUSER’S GUIDE2W8000FMR2W8000FMR-2ndBy Firstech, LLC.www.compustar.comTwo-Way FM Remote2W8000FMR /2W8000FMR-2ndFCC ID : VA5J2W8000RThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired operation. CAUTION : Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate this device. IC : 7087A-2W8000RStatement: The term “IC:” before the radio certification number only signifiesthat Industry Canada technical specifications were met.CAUTION: The User that modifications to the unit may void the user’sauthority to operate the unitMade in China
Page 23 egaPnoitamrofnI ytefaS .12. Remote-Pager : 2W8000FMR, 2W8000FMR-2nd W/LCD Page 44 egaPecnaraeppA etomeR fo noitpircseD .35 egaPDCL roloc OLGupmoC .45 egaPsnocI DCL .56 egaP snoitcnuF nottuB regaP-etomeR .67 egaP snoitcnuF nottuB eroM .78 egaPenituoR nraeL regaP-etomeR .89 egaPnoitcnuF tratS-otuA.910. Reservation Mode Page 1011. Canceling Reservation Mode Page 1111 egaPedoM telaV .2111 egaPserutaeF nwoD tuhS ytefaS .3114 [I-] 21 egaPgnimrA otuA21 egaPedoM obruT .5116. 2nd 21 egaPedoM rac31 egaP ytnarraW remusnoC emitefiL detimiL .7141 egaP ytnarraW ruoYTABLE OF CONTENTS...........................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................
Page 3Safety InformationPlease take these safety precautions into consideration under the followingconditions:1. Servicing the vehicleWhen servicing your automobile (i.e. changing the oil, washing your car), the CompuStarsystem should be in Valet Mode. There is a safety shutdown switch underthe hood that deactivates the remote start function if the hood is open. However, if the switch has been damaged or the switch has been installed improperly,the vehicle may start when button II is pressed for 2 seconds, even if the hood is open. 2. Loaning your vehicle to othersWhenever you loan your vehicle to an individual who is not familiar with Compustar, you may want to put the system in Valet mode. This will prevent the borrower fromaccidentally activating the CompuStar auto-security system.3. For manual transmission vehiclesIf the Compustar system is installed in a manual transmission vehicle, extra precautions are required because the Compustar does not monitor the gear shifter :Page 4This equipment has been tested and found to comply with the limits for a digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residental installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used inaccordance with the instructions, may cause harmful interference to radio communica-tions. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, whitch can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:-Reorient or relocate the receiving antenna.-Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to witch the receiver is connected.-consult the dealer or an experienced radio/TV technician for help.Important!Under normal circumstances, Reservation Mode is cancelled when a door or hatchback opens. Please verify that the opening of any door orhatchback cancels Reservation Mode. If any of the doors or hatchback are notmonitored by CompuStar because of improper installation or a faulty dome light switch,do not use the CompuStar and take your vehicle immediately to the dealer for repair.Do not set Reservation Mode if the window(s) are open or if there is anyone inside thevehicle, this includes animals. Remote start installation in a manual transmission vehiclewith a convertible top is not recommended.Remote-Pager : 2W8000FMR/ 2W8000FMR-2nd w/LCDThe model name, 2W8000FMR, 2W8000FMR -2nd is a Two Way 433MhzFrequency Modulated Remote with Liquid Crystal Display.This transmitter allows you to activate multiple functions by pressing differentcombinations of the 4 buttons on the unit.Description of Remote AppearanceFront Side Rear
Page 5 Page 6The remote-pager comes with CompuGLO, which is a unique color LCD displaythat visually tells you the security status of your vehicle as long as you are in range. There are differing icons that will appear on your CompuGLO LCD indicating what your vehicle is currently doing. CompuGLO color LCD2W8000FMR-2nd2W8000FMRLCD IconsIndicates that Timer Mode is on. Indicates that Turbo Mode is on. ( 2W8000FMR )Indicates that Passive Arming Mode is on. Indicates that 2nd Vehicle Mode is on. ( 2W8000FMR-2nd )Indicates that the Shock Sensor has been triggered.Indicates that Shock sensor is turned off.noitanalpxEnocIIndicates that you are in Valet Mode.Indicates that your parking lights are flashing.Indicates that your siren is turned on.(Locking and unlocking only.)Indicates if the Auto Lock/ Unlock mode is on. ( Icon flashes for longer range.) Indicates that someone is paging you from your vehicle.Indicates that your car is locked or unlocked. Indicates that your remote-pager is transmitting signals to thecontroller unit.Indicates that vibration mode is on.Indicates if RPS is on.Displays remaining battery life.1. Time Clock.2. Remainder of the engine running time. Indicates that your vehicle has auto-started properly or that theignition is on.Indicates that your trunk is open.Indicates that your hood is open.Indicates that your door is open.Remote-Pager Button Functions56781/2 secIIIIIIVIII1/2 sec1/2 sec1/2 sec1/2 secLock / ArmUnlock / DisarmAUX 1 AUX 2 Query FunctionAuto-start Function – on/offButton(s)Pressed ForFunction1234III2 sec2 sec2 secAuto Arming turned On.(Auto icon will be turned on).Longer range Auto Arming On.(Auto icon Flashes.)Auto Arming turned Off.
Page 7 Page 8(2) RPS & Vibration mode on or off Note : Step 2 must be completed within 15 seconds. If not, start over at step 1.Tones will sound for confirmationSTEP 1(II+III)2 secButtonPressedForFunctionSTEP 2RPS on or off, tones will sound for confirmation.Vibration mode on or off, tones willsound for confirmation. (III)(IV)1/2 sec1/2 secNote: " " Represents pressing the button for 2 seconds." ( ) " Represents simultaneously pressing the buttons." ( ) " Represents simultaneously pressing the buttons for 2 seconds.Ibutton Proceeds in (1) (2) (3) (1)..... repeatedly. At (2) , the icon will flash.Note : 8910111/2 sec1/2 sec1/2 secIIIIIIV(I + II)2 sec 2 sec 2 secTrunk Release Auto-start Function – on/offPanic, Press Ito turn off the siren.Siren Chirp – on/offValet Mode – on/offPassive Arming – on/offTimer Start Mode – on/offTurbo Mode - on/off (2W8000FMR)2nd Car - on/off (2W8000FMR-2nd)Shock Sensor – on/off 121415161718(I + III)(II + III)(II + IV)(III + IV)(I + III)(I + II) (I + IV)1/2 sec1/2 sec2 sec2 sec2 secProgramming Menu 1Programming Menu 213More Button Functions(1) Time SettingTones will sound for confirmationSTEP 1(II+III)2 secButtonPressedForFunctionTime setting is on. The numbers willflash, and tones will sound.STEP 2(I)(II+III)1/2 secChange hour.Change minutes.Time setting is off. Tones willsound.STEP 3STEP 4(I)(II)1/2 sec1/2 sec2 secRemote-Pager Learn RoutineThe Compustar system will allow up to three remotes to be programmed to onevehicle. Please perform the following procedure to add or reprogram additionalremotes.Step1 :Activate Valet/Programming mode by manually turning the ignition on and off five times(between Acc and On)with the key within a 7 second period.The parking light will flash once with successful completion of this step.Step2:Within a 7 second period after cycling the ignition for the 5th time,press button I. The parking lights will flash once to confirm that the transmitter has been programmed. You can continue programming additional remotes. The parking lights will flash two times when the programming mode has expired.
Page 9 Page 10shows the amount of run-time left in the remote start mode.Press button IIfor 2 seconds to auto-start an automatic transmission engine.Remember, that a key in the ignition is required to drive the car.For manual transmission vehicles, please use reservation mode. Press button IIfor 2 seconds in order to turn off an auto-started car.The engine will run 15 or 25 minutes (25 or 45 min for diesel) depending on presetoptions at the time of installation and then shut off.Auto-Start Function Anti-GrindThe anti-grind circuit (an optional feature provided by your installer) prevents youfrom engaging the starter on a remote-started vehicle.Diagnosing problems with Auto-Start If there is a problem in auto-starting your vehicle,the CompuStar system will do oneof two things; if it fails for any of the reasons listed in the table below, it will flash theparkinglights three times then flash the error number. Otherwise, it will attempt tostart the vehicle three times. If, after three times, the vehicle will not start or stayrunning, the CompuStar system will shut down. In either case, please see yourinstaller to resolve the situation.1234567Error Number(# of timesparking lights flash) Error ReasonEngine OnKey OnDoor OpenTrunk OpenBrake On Hood OpenReservation Off (Manual Transmission Only)Reservation Mode(manual transmission only)In order to auto-start your manual transmission vehicle, you must first set theCompuStar system to Reservation Mode before leaving your vehicle. The purposeof Reservation Mode is to leave the transmission gear in the neutral position whenyou leave your vehicle. Reservation mode is intended for use on MANUALTRANSMISSIONS ONLY and NOT FOR AUTOMATIC TRANSMISSIONS.Reservation Mode must be engaged each and every time you leave your manualtransmission vehicle in order to auto-start it.Note : The system is not recommended for vehicles with removable tops.Important requirements to activate Reservation ModeThe transmission must be in the NEUTRAL position. The vehicle windows must be rolled up. Do not set the reservation mode with people in the vehicle. Do not auto-start the vehicle with people in the it. Activating Reservation Mode(Manual Transmission only)Step1 : After arriving at your destination, and BEFORE TURNING YOUR ENGINE OFF, place the transmission in the Neutral position.Step2 : Activate the parking brake.Step3 : Remove your foot from the foot brake.Step4 : Remove the key from the ignition, and the engine will remain running.Step5 : Exit the vehicle and close the door within two minutes after activating the parking brake. The engine will shut off and reservation mode for the remote-starter is now complete.Your vehicle is now ready for auto-starting. However, the reservation mode will be cancelled if a door is opened or the CompuStar system is put in Valet modeafter the reservation has been set. Once cancelled, you will have to start the vehicle with the key and repeat the above 5 steps if you want to restore reservationmode.
Page 11 Page 12Important!When the vehicle shuts off after reservation mode, theCompustar system will lock/arm the vehicle. Take care to not lock your keysinside.Important!If you try to auto-start the vehicle when reservation modehas not been set, the auto-start feature will not work. When you press the auto-start button, the remote will beep three times. The car parking lights will flash three times, pause, then flash seven times. If you do not want to set reservation mode, shut off the engine before you exit the vehicle. The engine will shut off for the following reasons: You did not activate the parking brake or pressed the foot brake when you turned the key to the off position. You released the parking brake while the engine was running. You entered Valet Mode after the Reservation Mode has been completed. Canceling Reservation Modeaway from the vehicle by more than 50 to 100 ft, and (3) 15 seconds have passedsince the last Auto Disarm. Your system will disarm automatically if your remotecomes within a 50 to 100 ft radius from the vehicle. Setting Auto Arming Function.The range varies significantly depending on the radio signal environment.Each time you press button Ifor 2 seconds :First time : Auto icon is turned on.Second time : Auto icon flashes - for longer range.Third time : Auto icon is turned off.You can turn this function on or off by pressing button [I]for2 seconds. When Auto arming is set, your security system will armautomatically after (1) all the doors are closed, (2) your remote is [I]Auto ArmingWhile the vehicle is in valet mode, only the keyless entry function will be available.Valet Mode is very useful when loaning your vehicle or having it serviced.In order to enter Valet mode, press buttons (I+III)simultaneously for a 1/2 second.In order to manually enter Valet Mode, insert your key into the ignition and turn the ignition on, then off,(between ACC and ON)five times within 10 seconds.Valet ModeYou can exit Valet Mode only by pressing buttons(I+III)simultaneously for a 1/2 second. Safety Shut Down FeaturesThe CompuStar 2W8000FMR, 2W8000FMR-2nd system has several shut down safetyfeatures. The following actions will shut down the engine or prevent the car fromauto-starting : Opening the hood, pressing the brake, or if Valet Mode is turned on.Turbo ModeIf this optional Turbo Mode has been programmed at the time of installation,you can turn this feature on and off by pressing buttons(III + IV)for a 1/2 second.In this mode, if the emergency brake has been set, the engine will continue to run after the key has been taken out of the ignition. It will run until two minutes after theemergency brake has been set.• To utilize this mode, the emergency brake sensing wire has to be connected to theemergency brake wire of the vehicle. Consult the authorized dealer for this mode. • This option is ideal for turbo-charged vehicles because it allows the turbo too slowly cool after operation.(2W8000FMR)2nd Car ModeThis Remote-Pager is able to operate a 2nd vehicle.Press buttons III & IVsimultaneously for 1/2 second. If this mode is turned to 2nd Car,the Remote-Pager will not communicate with the 1st vehicle. To Exit 2nd Car pressbuttonsIII & IVsimultaneously again.(2W8000FMR-2nd)
Firstech, LLC Warrants to the original purchaser that this product shall be free of defects in material and workmanship under normal use and circumstances for the period of time that the original owner of this product owns the vehicle in which it is installed ; except that the remote controller unit for the period of one year from the date of installation to the original owner of this product. When the original purchaser returns the product to the retail store where it was purchased or prepaid postal to Firstech, LLC., 3415 S. 116th St Seattle, WA 98168, USAwithin the warranty period, and if the product is defective, Firstech, LLC, will at its optionrepair or replace such.TO THE MAXIMUM EXTENT ALLOWED BY LAW, ANY AND ALL WARRANTIES ARE EXCLUDED BY THE MANUFACTURER AND EACH ENTITY PARTICIPATING IN THE STREAM OF COMMERCE THEREWITH. THIS EXCLUSION INCLUDES BUT IS NOT LIMITED TO, THE EXCLUSION OF ANY AND ALL WARRANTY OF MERCHANTABILITY AND/OR ANY AND ALL WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND/OR ANY AND ALL WARRANTY OF NON-INFRINGEMENT OR PATENTS, IN THE UNITED STATES OF AMERICAAND/OR ABROAD. NEITHER THE MANUFACTURER OF ANY ENTITIES CONNECTED THEREWITHSHALL BE RESPONSIBLE OR LIABLE FOR ANY DAMAGES WHATSOEVER, INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIAL DAMAGES, INCIDENTALDAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIALLOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE. NOTWITHSTANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITED WARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Some states do not allow limitations on how long an implied warranty will last or the exclusion or limitation on how long an implied warranty will last or the exclusion or limitation of incidental or consequential damages. This warranty gives you specific legal rights, and you may also have other rights, which vary State to State.Limited Lifetime Consumer WarrantyPage 13Firstech, LLC. is not RESPONSIBLE OR LIABLE FOR ANY DAMAGESWHATSOEVER,INCLUDING BUT NOT LIMITED TO, ANY CONSEQUENTIALDAMAGES, INCIDENTAL DAMAGES, DAMAGES FOR LOSS OF TIME, LOSS OF EARNINGS, COMMERCIAL LOSS, LOSS OF ECONOMIC OPPORTUNITY AND THE LIKE that may or may not resulted from the operation ofCompustar. NOT WITH STANDING THE ABOVE, MANUFACTURER DOES OFFER A LIMITEDWARRANTY TO REPLACE OR REPAIR THE CONTROL MODULE AS DESCRIBED ABOVE. Your WarrantyThe product’s warranty is automatically void if its date code or serial number is defaced,missing or altered. This warranty will not be valid unless you have completed the registration card and mailed it to Firstech, LLC., within 10 days after the purchase to theaddress listed on the registration card.Page 14

Navigation menu