Ruio Communication Technology FRESHFUNB937 4G CPE User Manual

Ruio Communication Technology Co.,Ltd 4G CPE

User Manual

4G LTE CPEQuick StartLegal InformationCopyright @ 2017. All rights reserved.No part of this manual may be reproduced or transmitted in any form or by any means withoutprior written consent of and its affiliates.reserves the right change or modify any information or specification contained in this manualwithout prior notice and without any liability.Limitation of LiabilityDue to the nature of wireless communications, transmission and reception of data can never beguaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost.shall not be liable for any loss of profits or indirect, special, incidental or consequential damages
resulting from or arising out of or in connection with using of this product, whether or not hadbeen advised, knew or should have known of the possibility of such damages, including, but notlimited to lost profits, interruption of business, cost of capital, cost of substitute facilities orproduct, or any downtime cost.1 Introduction of RouterYour router is for indoor use only and multiple devices like computer, landline phone or externalstorage device can be connected to the router to access the Internet, make telephone calls, filessharing and more.The external antenna and USB ports are optionalApplication Scenarios:Scenario 1: 3G/4G mobile network service using a SIM cardScenario 2: Data service from Ethernet cord Internet connection (Ethernet Port)
Scenario 3: Data service from Ethernet cord and VOLTE voice using a SIM cardAppearance
1Telephone ports8WPS button2LAN port9SYS indicator3WAN port10RF indicator4Power Input11WiFi indicator5Standard SIM card slot12ETH indicator
6Power button13NET indicator7Reset button144G external antenna ports(Option)Important: Router does not support Micro/Nano SIM card or any other non-standard SIMcards.2 Setup your RouterInset a standard SIM card firstly as shown in the following diagram and then connect the poweradapter to the power input of the router.Press the Power button to turn on/off the router, and it will search for available mobilenetworks automatically.Do not inset or remove the SIM card when the router is running, as this may affectperformance or damage the SIM card.To shut down the router, press and hold the power button for approximately 3 seconds.The intuitive indicators display the router’s statusIndicatorStatusSYSPower indicatorOn: Device powered onOff: Device Powered offNETWireless Dialing indicatorSlow Blinking: Registered to a NetworkBlinking: Connected to a NetworkRFMore signal bars indicate stronger signalsWIFIOn: WiFi is enabledOff: WiFi is disabledBlinking: WPS connection set up in progressETHOn: Connected to the Ethernet network viaWAN port or LAN ports are usedBlinking: Data transfer3 ConfiguringYou can configure the router using the WebUI Settings page.1. Launch the Internet browser, and enter http://192.168.1.1 in the address bar.2. Enter the password, and log in to the web management page. The default password isadmin.You also can refer to the label on the backside of the router for the default IP addressand password.It’s strongly suggested to change the default login password of the WebUI to preventunauthorized users from changing the routers’ settings.
4 Connect to WiFi NetworkYou can connect your computer or mobile phone to the router’s WiFi network.Default SSID: FRESHFUN B937Default Password:It’s strongly suggested to change the default SSID and password by accessing to the WebUI WiFimanagement page to prevent unauthorized access to your WiFi network.You need to reconnect to the router’s WiFi network after changing the WiFi password.5 Access the internet through the WAN portYou can connect the router’s WAN port to the wall-mounted Ethernet port by Ethernet cable, andthen choose the working mode to be Broadband mode and configure the PPPoE/Static/DHCPparameters to access to internet.6 VOLTE & CS Domain Voice CallEnd Users can switch the internal and external antenna by install the external antenna on the SMA port directlyThe internal antenna is PCB type and default used, after the external antenna is installed, the internal and external antenna are alternativethe device will automatically switching to external antenna as there is a switch on the PCBA to controlthe switching behave(High or Low electrical level).
The router supports both VOLTE and CS domain voice call services. To change the call mode selectSettings > Phone and chose the desired option from the dropdown menu.For best results, the “Auto” setting of network mode is recommended.Please contact your network service provider for more detailed information.7 FAQS & TroubleshootingIf you are expecting any issues with the router, in most cases please try to restart the router orrestore the router to its factory settings.The illustrations in this guide are for reference purpose only and may not reflect the exactappearance of your product. Please contact your network service provider for more detailedinformation.How to restore factory settings?When the router is power on, click the reset button for approximately 3 seconds using a pointedobject until the indicator starts to blink. Restoring factory settings will clear all customizedsettings.How can I connect to the router by Wi-Fi Protected Setup (WPS) function?1. Ensure that WiFi is enabled on the client.2. Press the WPS button on the router to set up a WPS connectionHow to deal with the contents displayed issue of the WebUIManually clear your browser’s cache (for example, open you browser and choose InternetOptions > General > Browsing history > Delete.) and re-launch the WebUI page.Why the router does not work after I have finished configuring?1. Ensure that you have a working standard Sim card inserted properly.2. Move the router to an open space free from obstructions and make sure there are availablemobile networks.3. If the problem persists, please contact your network service provider.Why the Internet status indicator is persisting on, but the WiFi indicator is off?Your mobile network may have a poor signal. Try to move the router to a place with betterreception. An External outside antenna may be required to increase the network signal strength.Why can’t I access the router’s WebUI?1. Ensure that your computer is connected to the router through WiFi or the Ethernet cable.2. Ensure that your computer is set to obtain an IP address and DNS server addressautomatically.3. Restart your browser or try using another browser.4. If the problem persists, restore the router to factory settings and try to access WebUI again.8 Warning and NoticeSafety PrecautionsThis section contains important information about the operation of your device. It also containsinformation about how to use the device safely. Read this information carefully before using yourdevice.
Some electronic devices may be susceptible to electromagnetic interference. Locate therouter away from any TV set, radio and other electronic equipment to avoid electromagneticinterference.The router may interfere with medical devices, such as hearing aids and pacemakers.Consult a physician or the manufacturer of the medical device before using the router.Please keep yourself at least 20 centimeters away from router.Do not use your router in dangerous environments such as oil terminals or chemicalfactories where there are explosive gases or explosive products being processed.Please use original accessories or accessories that are authorized by . Unauthorizedaccessories may affect the router performance, damage the router or cause danger to you.Do not attempt to dismantle the router. There are no user serviceable parts.Do not allow the router or accessories to come into contact with liquid or moisture at anytime. Do not immerse the router in any liquid.Do not place objects on top of the router. This may lead to overheating of the device.The device must be placed in ventilation environment for use.Do not expose the router to direct sunlight or store it in hot areas. High temperature canshorten the life of electronic devices.Do not allow children to play with the router or charger.Keep the length of the cable between the router and the phone less than 10 meters.The router is for indoor use only. Do not use the router outside. Do not connect telephoneextensions which run outside of the building. These can result in lightning damage to yourunit.Cleaning and MaintainingUse an antistatic cloth to clean the router. Do not use chemical or abrasive cleanser as thesecould damage the plastic case. Turn off your router before you clean it.Use the router within the temperature range of -10 ℃ ～ +65 ℃, and the storagetemperature range is -20℃～+85℃. The humidity range is 5%~95%.Do not remove your SIM card unnecessarily. The SIM card may be easily lost or it can bedamaged by static electricity.
FCC Caution: Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: —Reorient or relocate the receiving antenna. —Increase the separation between the equipment and receiver. —Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. —Consult the dealer or an experienced radio/TV technician for help. 

Navigation menu