Rayrun Technology RM06 Remote Controller User Manual

Rayrun Technology Co., Ltd Remote Controller

User Manual

2WHITEAllZone 1ZONEMODE+MODE-WHI TE2 3ZONEZONECOLOR+COLOR-ONLYWHI TEOFFSPEEDSPEED-+COLOR Thank you for purchasing our products. RQ211 and RQ212 4- ch RGBW LED controller is designed to drive constant voltage LED products with common anode connection in voltage range of DC6-24V. RQ211 is master unit controlled by a RF remote, RQ212 is slave unit synchronized with RQ211 wirelessly. User can program them to multi-zone group by the remote, and setup white or color lighting or synchronized dynamic modes in different zones.4-CH LED ControllerUser’s ManualRQ211 / RQ212RGBW 4-ch OutputWireless SychronizingFull ProtectionRF Remote ControllerWaterproof OptionUltra Slim DesignEasy Group SettingMulti-Zone ControlIntroductionInstalling12568Functions1. Turn On/ StandbyPress ‘I’ key to turn on unit or press ‘O’ key to turn off. At power on moment, unit will automatically restore to previous status before power cut.8. Remote Controller IndicatorThis blue indicator will blink when remote controller works.The remote controller works at radio frequency, the signal can pass through barrier, so it’s not necessary to aim at the controller when operate the remote.Wireless Synchronizing343. White BrightnessAdjust white LED brightness. Press the right side key to increase white LED brightness and the left side key to decrease.4. Static RGB Color SelectionThese keys control the RGB static color. a) Press color printed keys will set the RGB LEDs to correspond color light as the key. There are 6 shortcut color keys to make direct color selection.b) Press ‘COLOR+’ and ‘COLOR-’ to scroll over all preset static colors, including the 6 shortcut key colors.2. White ModeThese two keys control white LED working mode. Press ‘WHITE ONLY’ key, all RGB color will be shutdown and only white LED lights up. Press ‘WHITE OFF’ key, the white LED will turn off and RGB LED remain it’s previous status.5. Color BrightnessAdjust RGB color brightness. Press the right side key to increase RGB LED brightness and the left side key to decrease.6. RGB Dynamic Modes ControlThese keys control the RGB dynamic modes. a) Press ‘MODE+’ and ‘MODE-’ key to select preset dynamic modes.b) Press ‘SPEED+’ and ‘SPEED-’ to control the dynamic mode running speed.7. Zone ControlSelect the target zone controlled by remote. The RQ211 master unit is always zone 1 and the RQ212 slave unit can be programmed to any zones. The remote will control the corresponding zone(s) after the specific zone key is pressed once. For every power up for RQ211, the zone is restored to ‘All Zone’. RQ211 and RQ212 can be programmed to a group and operate in different zones. RQ211 is a master controller which receives remote control signal and sends out wireless commands to RQ212. RQ212 is slave controller and can only be programed to RQ211 master controller for group working. For proper wireless working, RQ212 should be in a good wireless receiving range from RQ211.7
56Specification910119. Power SupplyThe red power cable should be connected to power positive and black to negative. The controller unit can work from DC 6V to 24V, Please make sure the power supply voltage is same as the LED load and the power is capable for the load wattage.10. LED OutputRQ211/RQ212 supports constant voltage driving LED products with common anode connection. The black cable on the output side is the common node, it connects to the power supply positive inside the controller. The white, green, red and blue cable runs the driving signal of relevant LED color, please connect the color cables to the cathode of relevant color LED loads and the black cable to the common node.11. Status IndicatorThis is a full color status indicator. It displays all working status of the controller. It indicates different events as following:Blue: normal working.Short single white flash: new command executed.Long single white flash: reach mode or color cycle edge. Long single yellow flash: reach speed or brightness limit.Red flash: overload protected.Yellow flash: overheat protected.Operation12. Using RemotePlease pull out the battery insulate tape before using. The RF wireless remote signal can pass through some nonmetal barrier. For proper receiving remote signal, please do not install the controller in closed metal parts. 13. Pairing New RemoteThe remote and RQ211 is 1 to 1 paired as default. Further more, one master unit can be paired to 5 remote controllers and every remote can be paired to any master unit. Please do following steps to pair new remote to RQ211:1). Plug off the power of RQ211 and plug in again after 5 seconds.2). Press remote ‘ON’ and ‘White Bright +’ key together in 5 seconds after RQ211 power on, and then press ‘RED’ key in another 5 seconds.After this operation, the RQ211 indicator will flash white for 3 times to display the command is accepted, the master unit now recognizes the new remote. Only 5 latest paired remote controllers can be recognized by RQ211.14. Program Slave to ZoneThe RQ212 slave controllers can be programmed to zone1, 2 or 3. There’s no quantity limit in each zone group. Do the following steps to program slave controller to master:1). Keep the RQ211 controller power on and the remote already paired to it.2). Plug off the power of RQ212 slave controller and plug in again after 5 seconds.3). Press remote ‘ON’ and ‘White Bright +’ key together in 5 seconds after RQ212 power on, and then press ‘1 ZONE’, ‘2 ZONE' or ‘3 ZONE’ key in another 5 seconds.After this operation, the RQ212 indicator will also flash white for 3 times to display the programming is accepted, the slave is now programmed to the relevant zone.Advanced Features15. WaterproofRQ211/212 is a standard version which can be used in dry environments. RQ211/212-S is fully waterproof with IP68 standard, and can be used under water within depth of 30 meters.Note: The remote receiving and master to slave communication sensitivity will decrease when controller installed in wet environment.16. Protection RQ211/212 series controllers have full protection function for output short circuit, overload, and overheat. The controller will automatically recover from protection when working status is good. Please ensure the LED loads are in rated range, outputs are not shorted and the controller unit is in a good heat dissipation environment to avoid protection.Model RQ211 RQ211-S RQ212 RQ212-SDynamic mode 34 modesStatic Color 30 colorsPWM Grade 256 stepsWhite Brightness Grade 10 levelsColor Brightness Grade 5 levelsSpeed Grade 10 levelsDirect Color Select 6 direct keys NoneOverload protection YesOverheat protection YesWorking Voltage DC 6-24VRemote frequency 433.92MHz NoneSynchronization frequency 2.4GHz ISM bandRemote control distance >15m at open area NoneMaster/Slave sync. >15m at open areaZone Control 3 zones, infinite RQ212 in each zone.Rated Output Current 3x2.5A + 4AIP Grade IP-63 IP-68 IP-63 IP-68This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference;(2) This device must accept any interference received, including interference that may cause undesired operation.Caution:Any Changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operatethe equipment.

Navigation menu