R tron SNIDEN30 iDen Mini Wireless Repeater User Manual

R-tron Inc. iDen Mini Wireless Repeater

Contents

Part 2

iDEN MINI User’s Manual -15- 2.2.4. MCU (Main Control Unit) MCU is the control unit of iDEN MINI. It controls and monitors operational parameters. It also generates alarms, an event log and many other functions of the iDEN MINI. Figure 8. Main Control Unit Pin Map Port Connected to J1 MCU Vcc(+12V) J3 USB Port(Manufacturer use only) J4 PSU Alarms J5 Door Alarm J6 Status LEDs J7 iDEN 800 PLL,B/S,OUT DET J8 iDEN 900 PLL,B/S,OUT DET J9 Tx HPA J10 Rx HPA J11 RJ-45 port
iDEN MINI User’s Manual -16- 2.2.5. Power Supply The Power Supply Unit (PSU) supplies a steady DC power to iDEN MINI by drawing power from the general in-wall AC outlets. Figure 9. Power Supply Specifications Item Specifications Environmental Operating Temp -10°C~50°C/14°F~122°F Humidity 20%~90%RH Cooling method Natural air Voltage AC110~125V Current 6A Max / 6V, 12V, 27VDC Frequency 50~60Hz typ Leakage Current 0.5mA max.@110V AC
iDEN MINI User’s Manual -17- 2.2.6. HPAs (High Power Amplifiers) The High Power Amplifiers (HPAs) amplifies the transmitted signal from a base station at the final stage of the repeater and vice versa. Figure 10. HPAs(High Power Amplifiers)
iDEN MINI User’s Manual -18- 3. Hardware Installation The installation procedure is as follows:  Check List of Items  Mounting  Grounding  RF Connection  Power up 3.1 Check List of Items Index Items Q’ty 1 iDEN MINI 1 2 Power Cord 1 3 Screws for Mounting 4 4 Template for marking of the pilot holes 1 Items A-TYPEA-TYPEA-TYPE A-TYPEB-TYPEB-TYPEB-TYPE B-TYPEUse this template to markthe location for pilot holes Figure 11. Items 1 2 3 4
iDEN MINI User’s Manual -19- 3.2 Mounting iDEN MINI is easy to mount using the assembled mounting bracket, which has Ø9 holes for the provided 5/16" fixing screws. Figure 12. Mounting Step 1. Remove the cover of double-coated foam tape squares at each corner on the back side of the template. Step 2. Stick the provided template to the wall using the tape squares while adjusting the horizon. Step 3. Mark with a pen for the holes and drill the marks or drill holes directly on the mark in the template. Step 4. Put the screws or bolts into the holes. Step 5. Mount the iDEN MINI on the right position. CAUTION Firmly affix the equipment on the wall of a building and Check necessary.
iDEN MINI User’s Manual -20- 3.3 Grounding A rod on the left side is intended for a building ground. Connect the ground cable to the rod. Figure 13. Grounding 3.4 RF Cable Connection a. Connect a cable from a donor antenna to the DONOR ANTENNA Port. b. Connect a cable from the SERVICE ANTENNA Port to a repeater’s service antenna. WARNING Dangerously high voltages may occur and damage the equipment if the equipment is not groundedproperly.
iDEN MINI User’s Manual -21- Mobile StationDonor ServiceService antennaDonor antennaPlugged in an AC outletRepeaterBase Station Figure 14. Configuration: RF Cable Connection 3.5 Power Up a. Connect the power cord. b. Plug the power cord into a wall outlet. c. Check if the green LED at the bottom turns on. Figure 15. Power Cord Connection
iDEN MINI User’s Manual -22- 4. Command and Control through the Hyper Terminal 4.1 Setting for Command and Control through the Hyper Terminal Figure 16. Local connection to the iDEN MINI * iDEN MINI operates on a customer provided PC based platform with the following system requirements. Windows® 2000 or Windows® XP 128 MB RAM or more Pentium Ⅲ processor or more keyboard RJ-45 jack Step 1 Open My Network Places.
iDEN MINI User’s Manual -23- Step 2 Click the “View network connections”. Step 3 Push the right button of mouse and select the properties.
iDEN MINI User’s Manual -24- Step 4 Click the properties of TCP/IP. Step 5 Set the values and OK as the following. Close all windows.
iDEN MINI User’s Manual -25- Step 6 Execute the Hyper Terminal. Step 7 Name the session and OK. Step 8 Select the TCP/IP (Winsock).
iDEN MINI User’s Manual -26- Step 9 Set the values as the following and OK. 4.2 Command and Control through the Hyper Terminal Step 1. To see the current status, hit “Enter” key only.

Navigation menu