Quanzhou Chierda Electronic Telecom CDUV55 UHF-FM Hand Held Land-Mobile Transceiver User Manual Draft Manual

Quanzhou Chierda Electronic Telecom Co., Ltd. UHF-FM Hand Held Land-Mobile Transceiver Draft Manual

Contents

Draft Manual

SAFETYTRAININGINFORMATIONYourQuanzhouChierdaElectronicTeleco mCo.,Ltd.radiogeneratesRFelectromagneticenergyduringtransmitmode.Thisradioisdesignedforandclassifiedas“OccupationalUseOnly”,meaningitmustbeusedonlyduringthecourseofemploymentbyindividualsawareofthehazards,andthewaystominimizesuchhazards.ThisradioisNOTintendedforusebythe“GeneralPopulation”inanuncontrolledenvironment.ThisradiohasbeentestedandcomplieswiththeFCCRFexposurelimitsfor“OccupationalUseOnly”.Inaddition,yourQuanzhouChierdaElectronicTel ecomCo.,Ltd.radiocomplieswiththefollowingStandardsandGuidelineswithregardtoRFenergyandelectromagneticenergylevelsandevaluationofsuchlevelsforexposuretohumans: FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields.  American National Standards Institute (C95.1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz.  American National Standards Institute (C95.3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields– RF and Microwave.  The following accessories are authorized for use with this product. Use of accessories other than those (listed in the instruction) specified may result in RF exposure levels exceed the FCC requirements for wireless RF exposure. ToensurethatyourexposetoRFelectromagneticenergyiswithintheFCCallowablelimitsforoccupationaluse,alwaysadheretothefollowingguidelines:  DO NOT operate the radio without a proper antenna attached, as this may damaged the radio and may also cause you to exceed FCC RF exposure limits. A proper antenna is the antenna supplied with this radio by the manufacturer or antenna specifically authorized by the manufacturer for use with this radio.  DO NOT transmits for more than 50% of total radio use time (“50%duty cycle”). Transmitting more than 50% of the time can cause FCC RF exposure compliance requirements to be exceeded. The radio is transmitting when the “TX indicator” lights red. You can cause the radio to transmit by pressing the “PTT” switch.  ALWAYS keep the antenna at least 2.5 cm (1 inch) away from the body when transmitting and only use the HYT belt-clip which is listed in instructions when attaching the radio to your belt, etc., to ensure FCC RF exposure compliance requirements are not exceeded. To provide the recipients of your transmission the best sound quality, hold the antenna at least 5 cm (2 inches) from your mouth, and slightly off to one side. TheinformationlistedaboveprovidestheuserwiththeinformationneededtomakehimorherawareofRFexposure,andwhattodotoas‐surethatthisradiooperateswiththeFCCRFexposurelimitsofthisradio.ElectromagneticInterference/CompatibilityDuringtransmissions,yourQuanzhouChierdaElectronicTele comCo.,Ltd.radiogeneratesRFenergythatcanpossiblycauseinterferencewithotherdevicesorsystems.Toavoidsuchinterference,turnofftheradioinareaswheresignsarepostedtodoso.DONOToperatethetransmitterinareasthataresensitivetoelectromagneticradiationsuchashospitals,aircraft,andblastingsites.Occupational/ControlledUseTheradiotransmitterisusedinsituationsinwhichpersonsareexposedasconsequenceoftheiremploymentprovidedthosepersonsarefullyawareofthepotentialforexposureandcanexercisecontrolovertheirexposure.
Thanks for buying the CHIERDA transceiver. This transceiver offers latest design; enhanced features, solid performance and easy accessibility. We believe you will be pleased with the high quality and reliable features for all your communication needs. . Please do not use the transceiver when you are in exploring places (such as gas, dust, smoke etc) . Please turn off the transceiver while your car is being refueled or parked a gas station. Operation instructions and training guidelines To ensure optimal performance and compliance with the occupational/controlled environment RF energy exposure limits in the above standards and guidelines, users should transmit no more than 50% of the time and always adhere to the following procedures: Transmit and Receive To transmit (talk), push the PTT button,; to receiver, release the PTT button. Hand-held radio operation Hold the radio in a vertical position with the microphone 5cms away from the lips and let the antenna farther away from you head Notices to the user . Government law prohibits the operation of unlicensed radio transmitters within the territories under government control. . Illegal operation is punishable by fine or imprisonment or both. . Refer service to qualified technicians Only. . It is important that the operator is aware of and understand hazards common to the operation of any transceiver. Explosive environment (such as gases, dust, fumes), turn off your transceiver while talking on fuel, or while parked in gasoline service stations. Measures: . Reorient or relocate the receiving antenna. . Increasing separation between the equipment and receiver. . Connect the equipment into and outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or and experienced radio/TV technician for help. Precautions Only qualified technicians are allowed to maintain this product
Do not use the radio or charge a battery in explosive areas such as coal gas, dust , steam, etc. Switch off the radio while refueling or parking at gas station Do not modify or adjust this radio without permission. No not expose the radio to direct sunlight over a long time, nor place it close to heating source. Do no place the radio in excessively dusty, humid areas, or on unstable surfaces. Safety: It is important that the operator is aware of and understands hazards common to the operation of any radio.
CONTENTS Unpacking and checking the equipment Supplied accessories Description of function Getting started LCD Display Description of transceiver Shortcut operation sheet How to operate Menu lock function Setting frequency step(STEP)—MENU 1 Setting squelch level(SQL-LE)---MENU 2 Setting power saver mode(SAVE)---MENU 3 Selecting transmitting power(TXP)----MENU 4 Setting transmitting beginning/ending prompt(ROGER)---MENU 5 Timer-out timer(TOT)----MENU + Setting VOX (VOX)----MENU 7 Setting wide or narrow bandwidth(WN)------MENU 8 Setting voice guide(VOICE)-----MENU 9 Setting transmitting overtime alarm(TOA)----MENU 10 Beep prompt function (BEEP)--------MENU 11 Setting power-on- message (PONMSG)-----MENU 12 Busy channel lockout(BCL)----MENU 13 Setting keypad lock(AUTOLK)-----MENU 14 Setting receiving CTCSS(R-CTCSS)-----MENU 15 Setting transmitting CTCSS(T-CTCSS)---MENU 16 Setting receiving DCS (R-DCS)------MENU 17 Setting transmitting DCS(T-DCS)--- MENU 18 Setting voice mode (APRO)-----MENU 19 Setting Calling Grade(SCR-NO)-----MENU 20 Setting scan mode (SC-REV)---- MENU 21 Setting SCAN/LAMP/SOS-CH/FM radio function on side key 1----MENU 22 Working mode (CH-MDF)---------MENU 23 Setting auto backlight (ABR)------MENU 24 Setting colorful background light-------MENU 25 Setting offset frequency (OFF-SET)----MENU 26 Setting frequency shift direction (SFT-D)---MENU 27 Setting Stopwatch timer function(SECOND)--- MENU 28 Channel name editing(CHNAME)--------MENU 29 Setting memory channel (MEM-CH)-----MENU 30 Deleting channel (DEL-CH)----MENU 31 Setting reset (RESET)--------MENU 32
CTCS/DCS scan (SCN CD)----MENU 33 DTMF encoding Editing/transmitting ANI –IN Code, ANI-ID Code transmitting delay and DTMF side tone Setting priority scan function Setting reverse frequency function Low voltage prompt Transmitting overtime prompt Adding scanning channel Wire-clone function Working with repeater How to use the intelligent charger Programming guide for software (via USB Programming cable) Troubleshooting Guide Technical Specification Appendix 1 (CTCSS) Appendix 2 (DCS) Technical specification Unpacking and checking of your equipment Carefully unpack the transceiver. We recommend that you identify the items in the following table before discarding the packing material. If any items are missing or have been damaged during shipment, please notify your Chierda dealer. Supplied accessories Description of functions
1. Dual frequency, dual band, dual display ,dual standby. 2. Frequency Range A. Standard frequency range for the two-way radio 400-470MHz (RX/TX) B. Optional Frequency Range 400-470MHz((RX/TX) 3. Working mode: U-V,V-V or U-U selectable. 4. Channel setting: UHF TX selectable. 5. DTMF encoding 6. Digital FM Radio (76-108MHz) 7. CTCSS/DCS scan 8. Output power: 4W UHF 9. 128 memory channels 10. VOX 11. Stopwatch timer function 12. 105 groups DCS and 50 groups CTCSS 13. Voice guide 14. SOS function 15. Wide/narrow bandwidth selection (25khz/12.5khz) 16. Multi-display modes (Channel order number/channel frequency/channel name selectable) 17. Reverse frequency 18. Multi-function function 19. Priority scan function 20. Frequency steps selectable (5/6.25/10.12.5/25/50/100khz) 21. High/low power changeable when transmitting 22. High capacity li-ion battery pack 23. Intelligent charger 24. Offset frequency setting (0-69.950MHz) 25. Frequency shift direction setting 26. Busy channel lockout 27. Power-on message (battery-V/full screen/other characters) 28. Low voltage prompt 29. Transmitting beginning/ending prompt 30. Transmitting overtime prompt 31. Keypad locks(auto/manual) 32. Adding scanning channel 33. High/low power switch able when transmitting 34. Programmable by computer 35. Wire-clone function 36. Menu/channel reset Getting started LCD display
There are various indicators displaying on the screen when powering on. Please refer the below table to learn what the indicators stand for accordingly. Note: Quickly switch the working mode (MENU+TDR) Quickly resume the transceiver (MENU+ A/B)
Quick search Turn encode knob one time to search the desired function or parameter when setting for each function or parameter, while keeping turning encoder knob to quickly search. Single/dual band switch Press Single band <---------------------------> Dual band Quickly resume the transceiver In standby , press then LCD display . Press to confirm, and then the transceiver re-start. A/B Switch Press to select the master frequency. The frequency with arrowhead mark is the master frequency, while the other frequency without arrowhead mark is the sub frequency. The transceiver can transmit and receive in the master frequency , but only receivers in the sub frequency. When it is receiving in the sub frequency, there shows “S” in the screen. Key Short press the key to set the reverse frequency, while keeping pressing for 2 seconds to active the scan function, also have optional-signal-call function. Side key 2: Monitor function
. Quick search to turn encoder . Programming guide(see page 49-50) . High/low power changeable (see page 16) . SOS-CH(SOS function)(see page 26) . DTMF encoding (see page 40) . Priority scan function(see page 42) . Set reverse frequency (see page 43) .Low voltage prompt (see page 44) . Setting transmitting overtime prompt (see page 44) .Adding scanning channel function (see page 44) .Wire-clone function (see page 45) Working with repeater (see page 46-48)
How to operate Menu lock function Sometimes if the menu is not need to operated frequency, you can lock the menu via the programming software. Please see the detailed steps as follow: 1. set channel mode as the working mode. 2. turn off operating menu function in the channel mode If you want to operate menu function, can activate menu available of channel of mode by programming software, then change the working mode to frequency mode. . in dual standby mode, the screen shows “TDR” , the frequency with arrowhead mark is the master frequency while the other without arrowhead mark is the sub frequency, when the sub frequency is receiving, there shows “S” in the screen. In the dual standby mode, the transceiver only transmits in the master frequency and receives in the sub frequency. . mater frequency setting In dual standby, press A/B to select the master frequency. . this transceiver is the dual band, with dual frequency and dual display functions. In frequency mode, it can display two different receiving/transmitting frequencies at the same time. In channel mode, it can also display the channel frequency and related parameter in both channels at the same time. .in frequency/channel mode, it is switch able between band A and band B by A/B key, when the A/B indicator shows in band A, all the operations are based on band B. .in frequency mode, it is available to separately set the frequency step, transmitting power, squelch level , bandwidth, CTCSS/DCS, offset frequency, frequency shift direction and channel display modes in band A or band B. .in channel mode, it is invalid to set frequency step, transmitting power, CTCSS/DCS, bandwidth, offset frequency, and frequency shift direction and channel display modes in band A or band B.
Setting frequency step (STEP)-----MENU 1 In standby ,press , the screen displays Press to enter, it shows “12.50K”, turn encoder to select the desired step, then press to confirm, finally press to return to standby. The frequency steps selectable for this transceiver are as follow: 5.00khz,6.25khz, 10.00khz,12.5khz,25.00khz,50.00khz,100.00khz Setting squelch level (SQL-LE)-----MENU 2 Squelch level is about when the signal is strong enough to turn on the squelch function, and when it is weak enough to turn off the squelch function. When the squelch is on, there is voice from the loudspeaker for all the signaling set by the transceiver. When the squelch level is set too high, the weaker signals may be missed, while the squelch level is set too low, the transceiver maybe disturbed by some novice or other needless signals. . The squelch level for this transceiver has 0~9 levels selectable, and level 0 is to turn off the squelch function. The higher level the squelch is set, the stronger receiving signal is needed. In standby , press ,the screen display Press to enter, it shows “5”, turn encoder to select the desired squelch level, then press to confirm, finally press to return to standby. Setting power saver mode (SAVE)-------MENU 3 When the power saver function is on, the receiver circuit will be cut off for the moment, and then re-activate to detect the signals for a while, in order to reduce the battery capacity consumption. In standby , press ,the screen display Press to enter, it shows “5”, turn encoder to select turn on/off the power saving function, then press to confirm, finally press to return to standby.
Selecting transmitting power (TXP)-----MENU 4 In frequency mode, press the screen displays Press to enter, it shows “high”, turn encoder to select high/low power,, then press to confirm, finally press to return to standby. . this transceiver has high and low transmitting power selectable: UHF: High: 4W, LOW:1W . The quick switch between the high and low transmitting powers is temporary. In transmitting mode, press key to quick switch the high/low transmitting power. Once the transceiver is resumed, the transmitting power reverts to the original output power. Setting transmitting beginning/ending prompt (ROGER)-------MENU 5 This function is to select the prompt modes when beginning/ending transmitting as followings: OFF: press and release PTT key, there is no prompt for either beginning or ending transmitting. BOT: press PTT key, there is prompt for the beginning transmitting. EOT: Release PTT key, there is prompt for the ending transmitting. BOTH: press and release PTT key, there is prompt for both beginning/ending transmitting. In standby , press ,the screen display Press to enter, it shows “OFF”, turn encoder to select OFF/BOT/EOT/BOTH,, then press to confirm, finally press to return to standby. Time-Out Timer (TOT)---------MENU 6 This function is to prevent the transceiver from transmitting for too long time. When the transceiver is exceeding the press time limit , it will stop transmitting with an overtime alarm. This transceiver can be set in 40 levels with 15 seconds each, between 15 and 600 seconds. In standby , press ,the screen display
Press to enter, it shows “60”, turn encoder to select the desired transmitting level, then press to confirm, finally press to return to standby. Setting VOX (VOX)-------MENU 7 This transceiver will switch to the transmitting mode when detecting the voice signal. The transceiver operation will somewhat be delayed, and the voice signal information maybe not transmitted at the first beginning, since there needs some time for the VOX circuit to detect the voice signal. In standby , press the screen display Press to enter, it shows “OFF”, turn encoder to turn off VOX function or select VOX level (1~10), then press to confirm, finally press to return to standby. . The higher level of VOX is set, the higher volume is needed. . In scan and radio modes, the vox function is not available, but just showing VOX mark on the upper right of the display screen. Setting wide or narrow bandwidth (WN)-------MENU 8 In standby , press ,the screen display Press to enter, it shows “wide”, turn encoder to select the desired step, then press to confirm, finally press to return to standby. Setting voice guide(VOICE)---MENU 9 In standby, press , the screen displays Press to enter, turn encoder to select Chinese , English or OFF, and then press key to confirm, finally press to return to standby
. Please turn off MENU 9 and MENU 11 at the same time to turn off all the voice prompt for this transceiver Setting transmitting overtime alarm (TOA)-----MENU 10 This alarm is the pre-alert time when the transmitting time is nearly up to requested transmitting time. When the time is up , the transceiver sounds out the beep prompt and the LCD keeps flashing. This transceiver can be set from 1-10 TOA level with 1 second each. Level 1 means that the prompt 1 second ahead when the transmitting time is up to the TOT preset time. In standby, press , the screen displays Press to enter, it shows “5”, turn encoder knob to select OFF/1-10 Level, then press key to confirm, finally press to return to the standby mode. Beep prompt function (BEEP)----MENU 11 Beep prompt function is for the transceiver operating confirmation, error status prompt or faulty reminders. We faithfully advise you to keep this function ON, so that you can detect or check the errors and faults in time. In standby, press , the screen displays Press to enter, it shows “ON, ”turn encoder to select turn ON/OFF the beep prompting function, then press key to confirm, finally press to return to standby . When MENU 9 VOICE function and MENU 11 beep function are both on at the same time ,the voice function is prioritized. Setting power on message (PONMSG)-----MENU 12 This transceiver has 3 display modes selectable for the power on message as follow: OFF: display the full screen BATT-V: display the current battery voltage MSG: display “welcome”.
In standby, press the screen displays Press to enter, it shows “OFF, ”turn encoder to select OFF/BATT-V/MSG., then press key to confirm, finally press to return to standby. Busy channel lockout(BCL)-----MENU 13 This function is to prevent the interference from the other communicating channels. When the selected channel is occupied by others, press PTT and there will be an alarm prompt for BCL, while release PTT, the alarm prompt disappears and the transceiver will be back to the receiving mode. In frequency mode, press , the screen displays Press to enter, it shows “OFF, ”turn encoder knob to select ON/OFF this function, then press key to confirm, finally press to return to standby. Setting keypad lock (AUTOLK)-----MENU 14 This transceiver has automatically lock (AUTOLK) and manual lock selectable ON: When the AUTOLK is on, there are no operations within 15 seconds, the transceiver will be locked automatically. Press key more than 2 seconds to unlock the keypad. OFF: The AUTOLK is off, it is only available to lock the keypad manually. .According to the manual lock, press key for the more than two seconds to lock in standby mode, and press key for more than two seconds again to unlock it. In standby, press the screen displays Press to enter, it shows “OFF, ”turn encoder knob to select ON/OFF this function, then press key to confirm, finally press to return to standby. Setting receiving CTCSS (R-CTCSS)----MENU 15 Using the CTCSS/DCS can be used for you to receive the specified individual or group calls and avoid the needless callings from others with the same frequency. Only
receiving the same CTCSS/DCS signals, the transceiver can release the squelch. In standby, press the screen displays Press to enter, it shows “OFF, ”turn encoder to turn off this function or select 67.0hz to 254.1hz CTCSS code, then press key to confirm, finally press to return to standby. .This transceiver has 50 groups CTCSS, see appendix (1) CTCSS frequency sheet. Setting transmitting CTCSS (T-CTCSS)----MENU 16 In standby, press , the screen displays Press to enter, it shows “OFF, ”turn encoder to turn off this function or select 67.0hz to 254.1hz CTCSS code, then press key to confirm, finally press to return to standby. Setting receiving DCS (R-DCS)----MENU 17 In standby, press , the screen displays Press to enter, it shows “OFF, ”turn encoder to turn off this function or select 67.0hz to 254.1hz CTCSS code, then press key to confirm, finally press to return to standby. . This transceiver has 105 groups DCS, see appendix (2) DCS frequency sheet . In DCS selections, DXXXN(from D023N to D754N) means POSITIVE code, while DXXX (from D0231 to D7541) means NEGATIVE code.
Setting transmitting DCS (T-DCS)----MENU 18 In standby, press , the screen displays Press to enter, it shows “OFF, ”turn encoder to turn off this function or select 67.0hz to 254.1hz CTCSS code, then press key to confirm, finally press to return to standby. . This transceiver has 105 groups DCS, see appendix (2) DCS frequency sheet . In DCS selections, DXXXN(from D023N to D754N) means POSITIVE code, while DXXX (from D0231 to D7541) means NEGATIVE code. Voice mode (APRO)---MENU 19 In standby mode, press , the screen displays Then press to confirm, and then turn encoder knob to select OFF, COMP or SCR. And then press to confirm, finally COMP: companying voice signal, reduce noise, improve clear voice, especially distance between you far away(or one another). SCR: secret calling, it is unique dealing voice mode, other radio which have same frequency can receive scrambled and incorrect signal. OFF: turn off the above-mentioned functions for COMP&SCR. Secret Calling(SCR-NO)----MENU 20 In standby mode, press , the screen displays Then press to confirm, and then turn encoder knob to select from (1.2.3.4.5.6.7.8), 8 modes of secret in all, and then press to confirm, finally
Setting scan mode (SC-REV)---MENU 21 This transceiver has three scan modes: TO: the transceiver continues scanning if there are no any operations 5 seconds after receiving signals. CO: the transceiver pauses scanning when receiving signal, and continues scanning 3 seconds after the signal disappears. SE: the transceiver stops scanning when receiving signals. In standby mode, press , the screen displays Then press to confirm, it shows “TO, turn encoder knob to select TO/CO/SE scan mode, then press to confirm, finally press to return to standby mode. Setting Scan/Lamp/SOS-CH/FM radio/Optional-Signal Call on side key (PF1)---MENU 22 There are 4 functions selectable on the side key 1 of this transceiver 1.SCAN: scan function 2 LAMP: lamp function 3 SOS-CH: SOS function 4.RADIO: FM radio function 5. Call: (Opt-signal Call: MSK/2-Tone/5-Tone) 6. OFF: Disable this side key 1. SCAN Function In standby mode, press side key 1 enter to activate scanning (scan mode can be set through MENU 19-scan mode setting), while press any key to stop scanning in scan mode. In standby mode, press , the screen displays Press to enter, turn encoder knob to select SCAN, then press to confirm, finally press to return to standby mode. 2. LAMP function In standby mode, press side key 1 to turn on the lamp, and press this key again to turn it off. In standby mode, press , the screen displays Press to enter, turn encoder knob to select LAMP, then press to
confirm, finally press to return to standby mode. 3. SOS-CH (SOS function) In emergency, the transceiver transmits the SOS signals to the outside surrounding on the specified channel or frequency in band A or band B. Meanwhile, the transceiver will sound “wu…wu” with the green light keeping flashing. It will transmit signals every 5 minutes, lasting for 10 seconds each time. When the carrier signal receives in the SOS transmitting mode, the transceiver will automatically switch into the receiving mode. After the carrier signals disappear, the transceiver switches back to the SOS transmitting mode. Please press any key to exit in the SOS transmitting mode. . In case the SOS-CH frequency you set is not the master frequency , the transceiver will automatically set the SOS-CH frequency to be the master frequency in the SOS-CH mode. Meanwhile , the master frequency will not restore the settings before the SOS transmitting. . Please press key to reset the master frequency. In standby mode, press , the screen displays Then press to enter, turn encoder to choose SOS-CH submenu, the screen displays Press again to confirm, turn encoder to choose Band A or Band B, the press to confirm, the transceiver sounds “wu…wu..” meanwhile the RED/GREEN/FLASHLIGHT keeps flashing, while means SOS-CH function is on. After above settings, switch the transceiver to the standby mode, and press PF1 side key to transmit the
SOS signal. 4. RADIO function .Turning on the FM radio: in standby mode, press side key 1to turn on. The screen displays 145.025 22 then the indicator keeps flashing, which means transceiver is automatically turning the radio stations. Once the transceiver gets tuned, it stops at this radio station and starts the listening. .Turning on the FM radio station: in radio mode, press *SCAN , the radio keeps turning the stations automatically and the green light keeps flashing at the same time until it succeed in searching the available stations. You can turn encoder to manually turn the radio stations. .toring radio station: after detecting a radio station, presses MENU, the screen display SAVE?88.100, and then select one of the number keys from 1to 9 (1-9), the detected radio station will be stored into the clip for your future use. The transceiver has 2 groups of storages selectable for your storing, and the default group is the first storage. Egif you want to store 88.1MHz into the 1st group channel8, in radio mode, hen turning the desired radio station, press MENU +8W&N to store it into the 1st storage directly, if you want to store this frequency into the 2nd group channel 8. In radio mode, when turning the desired radio station, press # key then the screen will display . At this time, press to store this station into the 2nd group channel 8. in radio mode, press 1-9 to select the stored stations accordingly to listen to, while use the key to switch between 1st and 2nd storages. .Exiting from the radio mode: press side key 1 again to exit from the radio mode. 5. Call (Optional Signal Call) 3kinds of Opt-Signal Call (MSK、2-Tone、5-tone) are available, each can set 8 groups code , both MSK and 2-Tone can set 10 groups code, but the code of 5-Tone are not be limited. The codes for Optional-signal-call must be set by programming Software of the 2 way radio. MSK/2-Tone manually set code (but PF1 must be set CALL by Programming Software in advance) Call list and send out if relative calling list is not still edited, it will have beep tone prompt When 2-tone is editing in Programming software, code of A Tone form is transmit for 1second, code of B Tone form is transmit 3seconds, But code of A tone is transmit for 5 seconds when there is Only A tone edited in call List (it is regarded as group-call when it is used actually). Code of 5-tone is manually Edited (but PF1 must be set CALL by programming software via PC in advance). Press PF1 key , LCD display “CALL/----“, then input code of 5-tone you want, and
then press PTT key to call, that’s ok! Working mode (CH-MDF)---MENU23 This transceiver has 2options for the working mode: 1. Frequency mode (FREQ) 2.Channel mode There are 3 channel display selections in channel mode as follow: ① Channel (CH) ② frequency + channel (CH FREQ) ③channel name(NAME) Frequency mode (FREQ) and channel mode switchable (1) Without password input In standby, press then turn encoder to choose working mode and finally press to confirm. (2)With password input Please set the password for the mode switch via programming software. This password is consisting of 6charters from 0-9. The valid password should be made up by 6 digit except: 00000. In standby, press then turn encoder to choose one of FREQ/NAME/CH/CHREQ. Press to confirm, the screen will display the password input . Please input the preset password through the keypad, then the transceiver will switch to the selected mode. Setting auto backlight (ABR) ---MENU24 In standby, press , the screen display Press to enter , it shows “ON”, turn encoder to turn ON/OFF auto backlight function, then press to confirm, press return to standby.
Colorful backlight (COLOR) ---MENE25 In standby mode, press then screen displays Then press to confirm, and then turn encoder to select Arabic number from (1-7), and then press to confirm again, finally Note: every Arabic number means a kind of colorful backlight. E.G：1 means red backlight, 2 means green backlight, 3 means yellow backlight, and 4 means blue backlight and so on. Setting offset frequency (OFF SET) ---MENU 26 Offset frequency means the difference between transmitting frequency and receiving frequency. The range of the offset frequency for this transceiver is from 0-69.950 MHz In standby mode, presses , the screen displays Press to enter, and then turn encoder to select the listed offset frequency, or manually input through in order to transmit and receive in different frequencies, it is necessary to set the offset frequency shift direction in the frequency mode. Please follow the below setting steps: 1. Set the working mode to the frequency mode. 2. Set the frequency shift direction and offset frequency. Eg: in frequency mode, the transceiver needs to work on receiving frequency 450.025 MHz and transmitting frequency 460.025 MHz. In frequency mode, input to select positive direction (+), press +turn encoder knob to choose 10.000+ , so the frequency shift direction and offset frequency are set. The screen displays , press PTT to transmit and the screen displays ，release PTT, the screen displays ，and it means receiving frequency is , while the transmitting frequency is
Setting frequency shift direction (SFT-D) ---MENU 27 There are 3 selections for the frequency shift direction setting:] 1. Plus shift (+), which means the transmitting frequency is higher than the receiving frequency. 2. Minus shift (-), which means the transmitting frequency is lower than the receiving frequency. 3. Turn off this function. In standby mode, press , the screen display press to enter, turn encoder to select +/-/OFF, then pres to confirm, finally return to standby mode. Selecting stopwatch timer (SECOND) ---MENU28 In standby mode, press , the screen display press to enter, it shows “OFF”, then turn encoder knob to turn ON/OFF this stopwatch, press to confirm, finally press to return to standby mode. Using the stopwatch timer: When this function is in, press key to start counting, while press any key to pause. Press key again to re-start counting. Channel Name Editing (CHNAME) ---MENU29 In frequency mode an din standby, you press , the screen display This means that the channel name is not edited up to now. 1. the method of editing do it via programming software or directly operate through the keypad manually. 2. with the following 2 items before editing you store/memory at least 1channel before editing channel name, specific operation detail is read in 30-setting channel memory the transceiver (two way radio) is in the channel mode, must press key to switch into the channel mode if it is in the frequency mode. 3. manual operation steps in the channel mode
The 1step: press key to confirm, the screen display The 2 step: after you press to confirm, at this time, you can edit the name of channel (1) If the channel name which you need is consist of 6 digital numbers （0 123456789）, directly input digital number key from keypad. Turn encoder clockwise to select the digit, turn encoder anti-clockwise for 1time, you will edit second number, and then you will turn clockwise for 1time again, the second digital number will appear. Then operation of editing next number according to the same theory. (2) If the 9-digit numbers of channel name is consisted of 1 English letter (from A-Z) or more (6 letters at most ) you will turn encoder clockwise to select English letter you want, these letters will appear after digital number 9 come out, and then turn encoder anti-clockwise 1time, you will select the second digit, and then turn encoder clockwise for 1time again. You will select digit according to the above mentioned theory as well as the 6th digit. The 3 step: After you finish selecting the 6digits of channel name, and then press , and press . Setting channel memory: setting Co-Channel and Dis-Channel (MEM-CH) ---MENU30 In frequency mode and in standby mode, it is available to store the desired frequencies and relevant parameter into the specified channel. Input the desired frequency, and then press , the screen display press to enter, turn encoder to select channel is co-channel. If you need to store as dis-channel, repeat the above operation on another frequency and transmitting frequency are stored as dis-channel. e.g: store receiving frequency450.025mhz and transmitting frequency460.025mhz into channel 20 as dis-channel.. 1. In frequency mode, input then press or turn encoder to select CH-20, press to confirm, voice prompt for receiving memory, then press . 2. Input ,
voice prompt for transmitting memory, then press 4. the dis-channel is set successfully. Deleting channel (DEL-CH) ---MENU31 In standby mode, press ，the screen display press to enter, and turn encoder to select the desired channel, then press to confirm, after the channel is deleted successfully, press to return to standby. 37
Setting reset---MENU32 This transceiver has 2selections for the reset operation- VFO reset and ALL reset. VFO reset means all the function parameter set in frequency mode resumes to the factory setting. ALL reset means all the function parameter set in both frequency mode and channel mode resumes to the factory setting. 1. VFO Reset In standby mode, press ，the screen display press to enter, and turn encoder to select VFO, then press ，the screen display press again to confirm, and the screen displays After this operation, the transceiver will be resumed automatically 2. All Reset 3. In order to avoid the faulty operations, we suggest that you set the password for the All Reset via programming software. Only input the valid password, the transceiver can be reset to the factory setting completely. Please see the password setting in the programming software, which is consist of six Arabic number selectable from 0-9. When the input password is 000000, it means no password is needed to input for this operation.
(1) setting password is 000000 In standby, press ，the screen display press to enter, and turn encoder to select ALL, press , the screen display then press again to confirm, the screen displays When the reset operation is done, the transceiver will be resumed automatically (2) setting password as xxxxxx (e.g 123456) In standby, press ，the screen display press to enter, and turn encoder to select ALL, press , the screen display , at this time input the valid password (e.g:123456), the screen displays then the transceiver will start resetting. After reset is done, the transceiver will be resumed automatically CTCSS/DCS scanning ---MENU33 When the transceiver detects the CTCSS/DCS signals, press ，the screen display press to enter, the arrowhead points to CTCSS, turn encoder select to scan CTCSS/DCS. And
then press to confirm, it starts scanning CTCSS/DCS frequencies. DTMF Encoding These keys and knob are respectively corresponding to A, B, C, D at DTMF encoding setting. Please follow the below steps to activate DTMF manually： 1. Hold on pressing PTT key to transmit. 2. AT the same time, press the keys on the keyboard to sent out the DTMF tone. Editing / Transmitting ANI ID Code, ANI ID Code transmitting delay and DTMF Side tone ·Editing ANI ID code ANI ID Code can be made up by alphanumeric (A-D and 0-9) with 6 digits max ·Transmitting ANI ID Code Turn this function on means when press PTT key, the ANI ID Code will be transmitted automatically, while turning it off means manually transmitting. ·ANI ID Code transmitting delay The delay time for transmitting ANI ID Code means the time which the transceiver is automatically delayed 41
transmitting ANI ID Code this delay can be set 3seconds max, total 30 levels with 100ms each. ·DTMF Side tone DTMF Side tone means to turn on/off the speaker when transmitting ANI ID Code, and get the corresponding DTMF tone. ·There are 4options on setting side tone: (1) Keypad side tone: press keypad to turn on side tone when transmitting (2) ANI ID Code side tone: transmit ANI ID Code to turn on side tone. (3) Key side tone + ANI ID side tone: press number key or transmit ANI ID side can turn on side tone when transmitting (4) OFF: in encoding mode, all side tones are off. Setting priority scan function If you want to monitor the other frequency and check the certain preferred frequency at the same time, You can set priority scan function. E.G: scan six channels: set CH1, CH2,CH3, CH4 and CH5 as the common scanned channels and CH6 as the priority scanned channel, then the scanning order is as followings:
When this transceiver detects signal on the priority channel when scanning, it will call on its frequency. Please program the priority channel via chierda programming software. Setting reverse frequency function When using the reverse frequency function, the transmitting and receiving frequencies of this transceiver will be interchanged, together with as well as all setting for CTCSS/DTMF. ·How to set the reverse frequency: In standby mode, press to activated this function, while press again to switch it off. ·In channel mode, if you want to: 1. turn on the menu setting. 2. reset the transceiver please program above operations via chierda programming software. Low voltage prompt When the battery pack is in low voltage, there will be voice prompt for the lower voltage, at this time, the backlight flashes one time every five seconds and the transceiver sounds out “click” to remind of being charged timely. Transmitting overtime prompt When the transmitting time is exceeding the preset time, there will be an alarm to remind of overtime transmitting, and the transmitting will be paused. If you want to continue transmitting, please press PTT to resume transmitting. (Please see MENU 6 about the time-out timer TOT) Adding scanning channel
Wire-clone function a. Install battery packs on source radio and target radio and connect then via wire-clone b. And then power target radio on c. Power on the source radio an hold on the MONI key at the same time d. Red LED on the source radio Flashes, while the green LED on the target radio flashes, it shows the wire cloning in completely proceeding Red LED flashing means transmitting data when wire cloning. Red LED will be extinguished after completing wire-clone, and the transceiver returns to standby. Red LED lasting flashing means the wire-clone is failed and the transceiver returns to standby mode Wire-clone setting Target radio Green LED flashing means receiving data when wire cloning. Green LED will be extinguished after completing wire-clone, and the transceiver returns to standby.
Working with repeater This series of transceiver is available to work with the repeater both in frequency mode and channel mode, which is programmable through the key board and via the programming software. Please refer to the following steps about manually programming the channels to work the repeater. a. set the transceiver work in the frequency/VFO mode, (if the radio work on channel mode, please press key to switch frequency mode ) b. Input the receive frequency through the keyboard. ( the receive frequency of this transceiver is the transmit frequency of repeater) c. Set the related parameter you need for this frequency, like MENU15-18 CTCDD/DCS, MENU 26 Offset frequency, MENU 27 shift frequency direction and others. d. Memorize this frequency and the parameter into the specified channel by MENU 30. e. After setting the Offset frequency and the shift frequency direction of receiving memory, you do not need to memorize the transmit frequency. After above, the settings to work with repeater are successful. Switch the working mode to channel mode, call out this specified channel you have memorized, the transceiver can join in the repeater.
For example, the receive frequency range of repeater is 442.850MHz, the offset frequency is 5.00MHz, the shift frequency direction is “-“, the T-CTCSS is 103.5hz, the specified channel CH-20. Please see the steps as following: a. Power on the transceiver, and set it to work in frequency mode. b. Press to set the frequency step, turn encode knob to select the desired frequency step, and then press to confirm, finally press to return to standby. c. Input the frequency447.850 through the keypad, and operate as follows: Press to set the transmitting power. Turn encode key to select the desired power, and then press to confirm, finally press to return to standby. (Please refer to MENU 4 on page 16) Press to set the T-CTCSS, turn encode key to select the desired CTCSS code 103.5HZ, and then press to confirm, finally press to return to standby. (Please refer to MENU 16 on page 23) Press to set the offset frequency, turn encode knob to select the desired offset frequency 5.00 MHz, and then press to confirm, finally press to return to standby. (Please refer to MENU 26) Press to set the shift frequency direction. Turn encode key to select the desired direction – and then press to return to standby. (Please refer to MENU 27)
Press to memory channel, turn encoder knob clockwise or anti-clockwise, or directly input through the keypad to select the specified channel CH-20, and then press to confirm,, there is voice prompt “receiving memory” (it prompts when the voice guide is ON). Finally press to return to standby. (Please refer to MENU 30) After above, the settings for memory channel to the repeater is done. If necessary for the channel name editing, please press to switch the working mode to channel mode. Select the specified channel CH-20, and then press to change channel mode. Turn encode key to select name and then press to confirm, finally press to return to standby. How to use the intelligent charger 1. Insert the AC plug into the power grid socket (AC: 110-220V). The indicator on the charger flashes, and then the charger is in the charger is in the charging standby mode. 2. Insert the battery into the charger, the RED LED is on, which means charging is on the progress. When the RED LED turns to GREEN, the charging completes.
Programming guide for software (via USB Programming cable) 1. Download, unzip and install the USB driver according to different operating system. 2. Restart your computer, and it shows the driver is installed successfully. 3. download and unzip the matching programming software 4. Connect the transceiver and open the software 5. Power on the transceiver and open the software 6. Read from the radio to check the connection 7. Set the parameter and functions accordingly 8. Wire to the radio ·if you get the message “failed connection” when you try to read from the radio, please check the first five steps and the communication ports accordingly. ·Please confirm that the first 3 steps are done well, the com port will be selected automatically when you open the software. However, according to the different computer settings, the com port may be needed to re-set. ·Please determine the port assignment form the device manager of the computer and select the correct commutation port, which is available for the connection. ·If the connection is still not ok, please try another cable or another transceiver on another computer to double check. Please refer to the detailed manual.
Troubleshooting Guide Before the transceiver is regarded as being faulty, please double checks according to the main problems as following chart, it the problems are still happening, please reset it to avoid some mis-function operation, search assistance from the experienced technician or contact your buyer accordingly. problem solution The transceiver can not be powered on ·The battery may be exhausted, please change the new battery or re-charge it ·The battery was not installed correctly, please re-stall The battery life is too short to use ·The battery life is over, please change a new battery ·The battery is not full charge The receiving light keeps flashing, But there is no sound coming out ·make sure the volume is highest ·make sure the CTCSS/DCS settings are the same as the transmitting transceiver It seems the keypad does not work ·make sure if the keypad is locked or not ·make sure if the keys are not stuck In standby, the transceiver will transmit automatically even the PTT key is not pressed ·make sure if VOX function is ON or not, and its level is set too low or not Some functions can not be stored normally ·please confirm if the transceiver is working in channel mode, since some functions are only set in frequency mode via programming software There are other disturbed signals or noise (from other groups) in the channel ·please change the CTCSS/DCS frequencies set in your group. Technical Specification Appendix 1 CTCSS 1 67.0 11 94.8 21 131.8 31 171.3 41 203..5 2 69.3 12 97.4 22 136.5 32 173.8 42 206.5 3 71.9 13 100.0 23 141.3 33 177.3 43 210.7 4 74.4 14 103.5 24 146.2 34 179.9 44 218.1 5 77.0 15 107.2 25 151.4 35 183.5 45 225.7 6 79.7 16 110.9 26 156.4 36 186.2 46 229.1 7 82.5 17 114.8 27 159.8 37 189.9 47 233.6 8 85.4 18 118.8 28 162.2 38 192.8 48 241.8 9 88.5 19 123.0 29 165.5 39 196.6 49 250.3 10 91.5 20 127.3 30 167.9 40 199.5 50 254.1
Appendix 1 DCS 1 D023N 16 D074N 31 D165N 46 D261N 61 D356N 76 D462N 91 D627N 2 D025N 17 D114N 32 D172N 47 D263N 62 D364N 77 D464N 92 D631N 3 D026N 18 D115N 33 D174N 48 D265N 63 D365N 78 D465N 93 D632N 4 D031N 19 D116N 34 D205N 49 D266N 64 D371N 79 D466N 94 D645N 5 D032N 20 D122N 35 D212N 50 D271N 65 D411N 80 D503N 95 D654N 6 D036N 21 D125N 36 D223N 51 D274N 66 D412N 81 D506N 96 D662N 7 D043N 22 D131N 37 D225N 52 D306N 67 D413N 82 D516N 97 D664N 8 D047N 23 D132N 38 D226N 53 D311N 68 D423N 83 D523N 98 D703N 9 D051N 24 D134N 39 D243N 54 D315N 69 D431N 84 D526N 99 D712N 10 D053N 25 D143N 40 D244N 55 D325N 70 D432N 85 D532N 100 D723N 11 D054N 26 D145N 41 D245N 56 D331N 71 D445N 86 D546N 101 D731N 12 D065N 27 D152N 42 D246N 57 D332N 72 D446N 87 D565N 102 D732N 13 D071N 28 D155N 43 D251N 58 D343N 73 D452N 88 D606N 103 D734N 14 D072N 29 D156N 44 D252N 59 D346N 74 D454N 89 D612N 104 D743N 15 D073N 30 D162N 45 D255N 60 D351N 75 D455N 90 D624N 105 D745N
Technical Specification Frequency range (can be suitable for different countries or Areas) 1.Standard frequency for the transceiver 400-470 MHz (Rx/Tx) 2. Optional frequency 400-470 MHz (Rx/Tx) Memory channel 128 channels Operating voltage 7.4v Operating temperature -30 to +60℃ Working mode Co-channel or Dis-channel simplex Output power UHF:4W Modulation F3E(FM) Max frequency deviation ﹤+5khz Spurious radiation ﹤-60db Frequency stability +2.5ppm Receive sensitivity ﹤0.2uv Audio output power ﹥500mw Dimension 120(L)*62(W)*41(T)mm Weight 250g NOTE: Specifications is subject to be updated without prior notice.

Navigation menu