Precise Biometrics MS010039 MIFARE Contactless Card & Fingerprint Reader User Manual Revised Users Manual

Precise Biometrics AB MIFARE Contactless Card & Fingerprint Reader Revised Users Manual

Contents

Revised Users Manual

Installation of Precise BioAccess¸2.1.Fasten the holder onto the wall.Mount Precise BioAccess¸onto the holder. Torque max 1.0 Nm.Plug the connector.4.3.1Do not connect2DATA (magstripe) / DATA 0 (Wiegand) OUTPUT3CLOCK (magstripe) / DATA 1 (Wiegand) OUTPUT4CARD PRESENT OUTPUT5 Tamper switch loop6 Tamper switch loop7 GROUND (power)8* Upper red LED (5V = on) INPUT9* Upper green LED (5V = on) INPUT10 POWER 12-24 VDC5. Secure Precise BioAccess¸.Use only screw driver Torx T10. *See Operation mode on opposite pageaccess control side of the system. Recomended mounting height 1,4meter/4.6 feet. Connect the wires using a shielded cable. The shielding must be connected to earth at the
Operation mode2.Unscrew the four screws on the back ofPrecise BioAccess¸.1. Loosen the top.2. Press back cover slightly upwards .3. Pull apart.AM010018 R1BMar. -02Installation ofPrecise BioAccess¸Dag Hammarskjöldsväg 2, SE-224 64 Lund, Sweden.Phone +46 46 311 100, Fax +46 46 311 101info@precisebiometrics.comwww.precisebiometrics.com1.3. ,Function ON OFF1. Sound Inactive * Active2. Upper LED control Active * Inactive3. Customized card No. Enabled * Disable4. RFU Forbidden! * Must be OFF*) Factory settingsCE Notice (Europe)This device meets the following technical standards as indicated by the symbolon the device:• EN 55022:1998 Limit B (Radiated emission)• EN 55024:1998 (Immunity of IT-equipment)• EN 61000-6-2:1999 (Immunity for industrial environments)• EN 300 330-2: v.1.1.1 (06-2001) (Radio - spectrum)• EN 301 489-01: v.1.2.1 (07-2000) (Radio - EMC)• EN 301 489-03 (07-2000) (Radio - EMC)FCC Information (U.S.A.)This device has been certified to the FCC rules and regulations (CFR47 Part 15 Subpart C) forthe low power transmitter contained within this device. In addition, this device has also beenverified to comply with Class B digital device requirements as specified in the FCCrules andregulations (CFR47 Part 15 Subpart B).This device complies with Part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) this device may not cause harmful interference, and (2) this device must acceptany interference received, including interference that may cause undesired operation.NOTE: This equipment has been tested and found to comply with the limits for a Class B digi-tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reason-able protection against harmful interference in a residential installation. This equipment gener-ates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However, thereis no guarantee that interference will not occur in a particular installation. If this equipmentdoes cause harmful interference to radio or television reception, which can be determined byturning the equipment off and on, the user is encouraged to try to correct the interference byone or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiveris connected• Connect the equipment into an outlet on a circuit different from that to which the receiver • Consult the dealer or an experienced radio/TV technician for helpCAUTION: Changes or modifications not expressly approved by the party responsible forcompliance could void the user`s authority to operate the equipment.

Navigation menu