Planex Communications MZK-KR150N 11n/g/b Wall-mount Wi-Fi router User Manual 0925402

Planex Communications inc. 11n/g/b Wall-mount Wi-Fi router 0925402

Users Manual

http://www.sapido.com.tw 1 USER MANUAL V1.0 PCI022_MZK-KR150NUS User Manual
2Notice Please notice and cooperate while using this product based on the statement below. a. FCC Section 15.105 This equipment has been tested and found to comply with the limits for a lass B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. -- Increase the separation between the equipment and receiver. -- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -- Consult the dealer or an experienced radio/TV technician for help. b. Please keep 20cm distance away from the antenna while using this product. c. Please don’t let this product co-exist or operate with any other transmitter while using it. d. FCC Part 15.19 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation e. FCC Part 15.21 information to user You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.
http://www.sapido.com.tw 2 USER MANUAL V1.0 Table of Contents FCC Caution ..........................................................................................................................................5 Safe Seating Gestures..........................................................................................................................6 Chapter 1 Introduction .................................................................................................................7 1.1 Overview ......................................................................................................................7 1.2 Features .......................................................................................................................8 1.3 Specifications..............................................................................................................9 1.3.1 Product Appearance ........................................................................................11 1.3.2 LED Indicator Status Description ...................................................................11 1.4 System Requirements ..............................................................................................12 1.5 Get Your IP Automatically & Manually ....................................................................12 1.5.1 Network Testing................................................................................................16 1.5.2 Testing with Internet Browser.........................................................................16 1.5.2.1 Testing with DOS (Windows XP Platform)......................................................... 16 Chapter 2 Hardware Installation................................................................................................19 2.1 Diagram of Connecting Hardware to PCI022_MZK-KR150NUS Broadband Router 19 2.1.1 Hardware Connection and Application for Router Mode.............................19 Chapter 3 One Button Setup......................................................................................................20 3.1 One Button Setup configuration for Router Mode ................................................20 Chapter 4 Router Setup..............................................................................................................24 4.1 Administrator Setup Instruction..............................................................................24 4.2 IP Configuration ........................................................................................................25 4.2.1 WAN ...................................................................................................................25 4.2.2 WAN Interface–3.5G (HSDPA/UMTS)..............................................................25 4.2.3 WAN Interface– Ethernet Port .........................................................................26 4.2.4 WAN Interface– WiMAX....................................................................................27 4.2.5 WAN Interface– Wireless .................................................................................28 4.2.6 WAN Access Type – Static IP ..........................................................................29 4.2.7 WAN Access Type –Dynamic IP......................................................................32 4.2.8 WAN Access Type –PPPoE..............................................................................34 4.2.9 WAN Access Type – PPTP...............................................................................36 4.2.10 LAN Interface Setup.........................................................................................39 4.2.11 Dynamic DNS Setting.......................................................................................41 4.3 Wireless Setup ..........................................................................................................42 4.3.1 Wireless Basic Settings...................................................................................43
http://www.sapido.com.tw 3 USER MANUAL V1.04.3.2 Wireless Advanced Settings ...........................................................................48 4.3.3 Wireless Security Setup ..................................................................................49 4.3.4 Wireless Access Control .................................................................................52 4.3.5 WDS Settings....................................................................................................53 4.3.6 WPS ...................................................................................................................58 4.4 NAT .............................................................................................................................63 4.4.1 Visual Server.....................................................................................................63 4.4.2 Visual DMZ ........................................................................................................65 4.5 Firewall.......................................................................................................................66 4.5.1 Port Filtering .....................................................................................................67 4.5.2 IP Filtering.........................................................................................................68 4.5.3 MAC Filtering....................................................................................................70 4.5.4 URL Filtering.....................................................................................................71 4.6 System Management ................................................................................................72 4.6.1 Change Password ............................................................................................73 4.6.2 Upgrade Firmware............................................................................................73 4.6.3 Profiles Save.....................................................................................................75 4.6.4 Time Zone Setting ............................................................................................79 4.6.5 UPnP Setting.....................................................................................................81 4.6.6 Language Setting .............................................................................................81 4.7 Log & Status ..............................................................................................................83 4.7.1 Network Config.................................................................................................83 4.7.2 Event Log ..........................................................................................................84 4.8 Logout........................................................................................................................86 Chapter 5 AP mode.....................................................................................................................87 Chapter 6 WiFi AP mode ............................................................................................................89 Chapter 7 DDNS Service Application........................................................................................90 Chapter 8 Q & A ..........................................................................................................................97 8.1 Installation .................................................................................................................97 8.2 LED.............................................................................................................................97 8.3 IP Address..................................................................................................................98 8.4 OS Setting..................................................................................................................98 8.5 PCI022_MZK-KR150NUS Broadband Router Setup ..............................................99 8.6 Wireless LAN...........................................................................................................101 8.7 Support ....................................................................................................................103 8.8 Others.......................................................................................................................104 8.9 USB Device..............................................................................................................104 Chapter 9 Appendices..............................................................................................................105
http://www.sapido.com.tw 4 USER MANUAL V1.09.1 Operating Systems .................................................................................................105 9.2 Browsers..................................................................................................................105 9.3 Communications Regulation Information ............................................................105
http://www.sapido.com.tw 5 USER MANUAL V1.0FCC Caution 1. The device complies with Part 15 of the FCC rules. Operation is subject to the following conditions: 2. This device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. 3. FCC RF Radiation Exposure Statement: The equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. 4. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 5. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment.
http://www.sapido.com.tw 6 USER MANUAL V1.0Safe Seating Gestures You should follow the manufacturer’s instructions for adjusting the backrest to fit your body properly. An adjustable chair that provides firm, comfortable support is best. Adjust the height of the chair so your thighs are horizontal and your feet flat on the floor. The back of the chair should support your lower back (lumbar region). CE Statement of Conformity Our product has been tested in typical configuration by Ecom Sertech Corp and was found to comply with the essential requirement of “Council Directive on the Approximation of the Laws of the Member States relating to Electromagnetic Compatibility” (89/336/EEC; 92/31/EEC; 93/68/EEC) Notice Changing RF parameter is not allowed.
http://www.sapido.com.tw 7 USER MANUAL V1.0Chapter 1 Introduction 1.1 Overview PCI022_MZK-KR150NUS Broadband Router is a convenient wireless solution for delivering 802.11n wireless connectivity with a maximum wireless signal rate of up to 150Mbps. Use it in home or company. Moreover, with connect to a 3.5G (EVDO/HSPA) or WiMAX USB modem, this PCI022_MZK-KR150NUS Broadband Router allows user to share the wireless network outdoor or be an alternative or backup to fixed broadband.
http://www.sapido.com.tw 8 USER MANUAL V1.01.2 Features y Wall mount : This product is recessed wireless router, not only allow multiple computers or Internet devices connect to the Internet easily , but can mount into wall. y UPnP Supported : insert your 3.5G or WiMAX modem card and enjoy the Internet without extra setting y 3.5G and Wireless PCI022_MZK-KR150NUS Combo : Ideal for mobility or backup for fixed lined connection y WPS button provides not only an easy and secured wireless network but also a WDS repeater in one push y Multiple APs Supported : adds or limits the properties for classed SSID, increasing the flexibility and efficiency of the network.
http://www.sapido.com.tw 9 USER MANUAL V1.01.3 Specifications Item Specification Key Components Main Processor Realtek RTL8196C (400MHz ) Flash 8Mbytes Serial Flash RAM 32Mbytes SDRAM Wireless Chip Realtek RTL8188RE-VL (MAC+BB+RF) 1T1R Communication Interfaces WAN/LAN Port 1 x 10/100 Mbps RJ45 with auto MDI/MDIX LAN Port 1 x 10/100 Mbps RJ45 with auto MDI/MDIX USB Port USB 2.0 host x1 (supports 3.5G or WiMAX USB dongle) Wireless IEEE 802.11 b/g/n Others Wireless Antenna External 3dBi x1 Transmission Power 802.11n : 22±2 dBm 802.11g : 23±2dBm 802.11b : 14±2dBm Receive Sensitivity 11Mbps : TYP. -83dBm @ 8% PER 54Mbps: TYP. -70dBm @ 10% PER 11n (20MHz): TYP. -64dBm @ 10% PER 11n (40MHz): TYP. -61dBm @ 10% PER Slide Switch Router / AP / WiFi AP Mode switch Button Power on/off button。 Reboot button / Reset button –1second for reboot；10seconds for reset WPS button。 Operation Requirement Operating Temp. 0 to 40℃ Storage Temp. -20 to 70℃ Operating Humidity 10% to 85% Non-Condensing Storage Humidity 5% to 90% Non-Condensing Power Supply AC100~240V / 50~60Hz universal input
http://www.sapido.com.tw 10 USER MANUAL V1.0Dimensions 72.6(L) x 48.1(W) x 49(D) mm (main body only) Device Weight TBD Notice: 1. USB device with power more than 500mA is not supported
http://www.sapido.com.tw 11 USER MANUAL V1.01.3.1 Product Appearance Power Receptor AC100~240V / 50~60Hz universal input WPS Push “WPS” button to looking for other WPS devices. The security will be set up between these 2 Wi-Fi devices after pairing. Reset Button Press “Reset” button over 10 seconds. When status indicator turns from flashing to solid, the process is completed. All settings are back to default. Ethernet Port 1x WAN port（back）, 1x WAN/LAN ports USB2.0 Ports 1 USB Port Mode switch Router/AP/WiFi AP mode WAN 1.3.2 LED Indicator Status Description LED Function Color Status Description On System is ready to work Status x 1 System status Green Blinking 120ms Rest to default in progress On Wireless is active Wireless / WPS x 1 Wireless activity & GreenBlinking Wireless Tx/Rx activity
http://www.sapido.com.tw 12 USER MANUAL V1.030ms WPS status Reddish OrangeBlinking 120ms WPS function in progress On 100Mbps Ethernet is connected Green Blinking 30ms 100Mbps Ethernet Tx/Rx activity On 10Mbps Ethernet is connected WAN/LAN x 1 WAN/LAN port activity Green Blinking 120ms 10Mbps Ethernet Tx/Rx activity On 100Mbps Ethernet is connected Green Blinking 30ms 100Mbps Ethernet Tx/Rx activity On 10Mbps Ethernet is connected LAN x 1 LAN port activity Green Blinking 120ms 10Mbps Ethernet Tx/Rx activity 1.4 System Requirements To begin with PCI022_MZK-KR150NUS Broadband Router, you must have the following minimum system requirements. If your system can’t correspond to the following requirements, you might get some unknown troubles on your system. XDSL/Cable Modem and broadband Internet Account. One Ethernet (10 BASE-T or 10/100 BASE-TX) network interface card. One PC or Notebook with web browser software installed (E.g.: Internet Explorer 5.0, Netscape Navigator 7.x, Apple Safari 2.03 or higher version). At lease one 802.11b/g/n wireless adapter for wireless mobile clients. Recommended OS: Win2000 or WinXP / Linux. 1.5 Get Your IP Automatically & Manually
http://www.sapido.com.tw 13 USER MANUAL V1.0After PCI022_MZK-KR150NUS Broadband Router connected with your computer, please make sure your IP is in the automatic IP position or you adjust it manually in order to activate the Internet network from home to Internet. If you don’t know how to enter the settings, please follow the steps as below. Step 1. Go to Start>Settings> Network Connections and then select Local Area Connection. Step 2. Click on Properties
http://www.sapido.com.tw 14 USER MANUAL V1.0 Step 3. Double click on Internet Protocol (TCP/IP). Step 4-1. For getting IP automatically if you are one of the users under PCI022_MZK-KR150NUS Broadband Router, please skip Use the following IP address and then select Obtain an IP address automatically and Obtain DNS server address automatically and then click on OK button.
http://www.sapido.com.tw 15 USER MANUAL V1.0 Step 4-2. For getting IP manually in order to specify a Virtual Server, such as Print Server, FTP Server and so on, please skip Obtain an IP address automatically and then select Use the following IP address. And the following default setting of PCI022_MZK-KR150NUS Broadband Router should be noted: y IP Address: 192.168.1.10 (as your Print Server for example) y Subnet Mask: 255.255.255.0 y Default Gateway: 192.168.1.1 Note: If you configure your computer’s IP Address manually, it needs to be on the same network segment. For example: z IP Address: 192.168.1.xxx (xxx can be any number between 2 and 253, but it can’t be repeated, we use 100 to be the example.) z Subnet Mask: 255.255.255.0 z Gateway: 192.168.1.1 (this is the IP address of PCI022_MZK-KR150NUS Broadband Router in Router Mode) z DNS: 192.168.1.1 (use PCI022_MZK-KR150NUS Broadband Router’s IP address or on your own choice) Note: IP address and Default gateway cannot be the same.
http://www.sapido.com.tw 16 USER MANUAL V1.0 1.5.1 Network Testing There are two ways to test your Network whether it can work on Internet or not. They are “Testing with Internet Browser” and “Testing with Dos”. 1.5.2 Testing with Internet Browser Open an Internet Browser, such as Internet Explore or Netscape. Input a valid web address you like, for example, http://www.yahoo.com in the web address blank and then press enter. If the website appears, that means your Internet is working under normal situation. 1.5.2.1 Testing with DOS (Windows XP Platform) Step 1. Go to start > Run.
http://www.sapido.com.tw 17 USER MANUAL V1.0 Step 2. Input cmd in the blank, and then click OK button. The Command Prompt window appears. Step 3. Input ipconfig in the flashing area then press enter. You will get an IP Address 192.168.1.100, for example, and Default Gateway as 192.168.1.1. Step 4. Ping a legal WAN Address such as 192.168.1.1. If Internet works, it will show Reply from 192.168.1.1: bytes = 32 time = 3ms TTL =64, for example.
http://www.sapido.com.tw 18 USER MANUAL V1.0 If it can’t work, it will show Request timed out.
http://www.sapido.com.tw 19 USER MANUAL V1.0Chapter 2 Hardware Installation 2.1 Diagram of Connecting Hardware to PCI022_MZK-KR150NUS Broadband Router PCI022_MZK-KR150NUS Broadband Router is a portable and convenient wireless solution for delivering 802.11n wireless connectivity with a maximum wireless signal rate of up to 150Mbps. Use it in conference rooms, hotel rooms, or even at hotspots. 2.1.1 Hardware Connection and Application for Router Mode When PCI022_MZK-KR150NUS Broadband Router switches to Router Mode, there will be each WAN and LAN port existing, the administrator can do the Quick Setup including WAN Setup, LAN Setup, Wireless Setup, Time Server Setup, Password Setup, Firewall Setup.
http://www.sapido.com.tw 20 USER MANUAL V1.0Chapter 3 One Button Setup The advanced One Button Setup provides users a simple way to set up the complicated network. Instead of numbers of IPs to be memorized, you just need to fill in some necessary information and then enjoy the secured internet by clicking the “Finished” button. 3.1 One Button Setup configuration for Router Mode The default UPnP of PCI022_MZK-KR150NUS Broadband Router is ON. When users connect PCI022_MZK-KR150NUS Broadband Router to their PC, and icon will show up in the right-down corner. Step 1. Click the Internet Gateway Device to open the login page.
http://www.sapido.com.tw 21 USER MANUAL V1.0 Step 2. Click One Button Setup on the left of the main menu under router mode.
http://www.sapido.com.tw 22 USER MANUAL V1.0 Time Zone Select: Select your time zone from the Time Zone drop-down list. Change Password: For changing password, please fill the password information into the blank. Device Name: Name your device here. The default is “PCI022_MZK-KR150NUS_Broadband_Router”. WAN Interface Setup: Select the WAN Interface from the drop-down list.
http://www.sapido.com.tw 23 USER MANUAL V1.0 Service: Select 3.5G service type. Connect Speed: Select connection speed. WAN Type Setup: Please choose the access type. Wireless Setup: Define the SSID, and Encryption type. Finished: Click finished button to complete the setting. Note: One Button Setup is not completed unless users finish all settings and click Finished button.
http://www.sapido.com.tw 24 USER MANUAL V1.0Chapter 4 Router Setup Under Router Mode, the 3.5G plus PCI022_MZK-KR150NUS Download Router provides a Router/AP function. User can get IP address assigned by ISP wired or wirelessly. It also supports NAT and DHCP functions that enable multiple computers to share an Internet connection at the same time. 4.1 Administrator Setup Instruction Open a Microsoft Internet Explorer, Mozilla Firefox or Apple Safari browser, and enter http://192.168.1.1 (Default Gateway) into browser’s blank. Notice: If the homepage doesn’t appear, please check if the TCP/IP configuration is obtaining IP address automatically or not. If you don’t know how to do it, please refer to “1.5 Get your IP Automatically & Manually”. Homepage The default values for User Name and Password are admin (all in lowercase letters). Click Login to enter.
http://www.sapido.com.tw 25 USER MANUAL V1.04.2 IP Configuration This function allows you to add routing rules into PCI022_MZK-KR150NUS Broadband Router. It is useful if you connect several computers behind PCI022_MZK-KR150NUS Broadband Router to share the same connection to Internet. 4.2.1 WAN Select WAN under the IP Config menu. PCI022_MZK-KR150NUS Broadband Router supports 3 interfaces and 4 access types. Follow the instructions below for each to set up accordingly. Choose your WAN Interface and WAN type, and click Next, its associated settings will show up. 4.2.2 WAN Interface–3.5G (HSDPA/UMTS) If you are using HSDPA/UMTS (3.5G connection) as the WAN Type, please select 3.5G USB Dongle. At this moment, Backup of Connection is not available. When 3.5G signal cannot be reached, the system starts to search downward for 3/2.75/2.5G signals until none existed.
http://www.sapido.com.tw 26 USER MANUAL V1.0 4.2.3 WAN Interface– Ethernet Port If you are using an Ethernet cable to connect the Internet, please select Ethernet port.
http://www.sapido.com.tw 27 USER MANUAL V1.04.2.4 WAN Interface– WiMAX
http://www.sapido.com.tw 28 USER MANUAL V1.0If you are using WiMAX as the WAN Type, please select WiMAX and fill in the required information as follows to directly access Internet via connected WiMAX adapter. 4.2.5 WAN Interface– Wireless If you are connecting the internet via wireless, please select Wireless and its associated settings will show up underneath at the same time.
http://www.sapido.com.tw 29 USER MANUAL V1.0 You can see a list of available Wireless networks. Select you preferred one to connect and the Encryption type form the drop-down list. 4.2.6 WAN Access Type – Static IP If you applied for a Static IP connection type from ISP, please follow the steps to set up your WAN connection.
http://www.sapido.com.tw 30 USER MANUAL V1.0 1. IP Address Input your IP Address supplied by ISP. If you don’t know, please check with your ISP. 2. Subnet Mask Input Subnet Mask, normally it is 255.255.255.0. 3. Default Gateway
http://www.sapido.com.tw 31 USER MANUAL V1.0Input ISP Default Gateway Address. If you don’t know, please check with your ISP. 4. MTU Size MTU stands for Maximum Transmission Unit. For Static IP connection, the default MTU should be provided by computer operating systems (OS). Advanced users can set the MTU manually for increasing the internet performance. The largest number allowed by Ethernet at the network layer is 1500 byte 5. DNS If ISP provides you DNS information, please select Attain DNS automatically, otherwise select Set DNS Manually and input the DNS information into the blank. 6. 3.5G Backup The default interval between the two connection detection is 3 minutes, and the range is from 1 to 60 minutes. Once Internet connection is disconnected, the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none existed. 7. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. 8. Enable IGMP Proxy The Internet Group Management Protocol (IGMP) is a communication protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. You can choose to enable IGMP Proxy to provide service. 9. Enable Ping Access on WAN Select Enable Ping Access on WAN, will make WAN IP address response to any ping request from Internet users. It is a common way for hacker to ping public WAN IP address, to see is there any WAN IP address available. 10. Enable Web Server Access on WAN This option is to enable Web Server Access function on WAN. 11. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the
http://www.sapido.com.tw 32 USER MANUAL V1.0input data. 4.2.7 WAN Access Type –Dynamic IP If your WAN access type is Dynamic IP, please complete the settings as following instructions. 1. Host Name The host name is optional; but if your ISP requires you to input a specific host name, please put it in, for example, PCI022_MZK-KR150NUS Broadband Router applied from ISP. Generally, Cable Modem will provide the hostname information.
http://www.sapido.com.tw 33 USER MANUAL V1.02. MTU Size MTU stands for Maximum Transmission Unit. For Static IP connection, the default MTU should be provided by computer operating systems (OS). Advanced users can set the MTU manually for increasing the internet performance. The largest number is 1492 byte 3. DNS If ISP provides you DNS information, please select Attain DNS automatically, otherwise select Set DNS Manually and input the DNS information into the blank. 4. 3.5G Backup The default interval between the two connection detection is 3 minutes, and the range is from 1 to 60 minutes. Once Internet connection is disconnected, the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none existed. 5. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. 6. Enable IGMP Proxy The Internet Group Management Protocol (IGMP) is a communication protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. You can choose to enable IGMP Proxy to provide service. 7. Enable Ping Access on WAN Select Enable Ping Access on WAN, will make WAN IP address response to any ping request from Internet users. It is a common way for hacker to ping public WAN IP address, to see is there any WAN IP address available. 8. Enable Web Server Access on WAN This option is to enable Web Server Access function on WAN. 9. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data.
http://www.sapido.com.tw 34 USER MANUAL V1.04.2.8 WAN Access Type –PPPoE If you applied for a PPPoE connection type from ISP, please follow the steps to set up your WAN connection.
http://www.sapido.com.tw 35 USER MANUAL V1.0 1. User Name Input your user name supplied by ISP. If you don’t know, please check with your ISP. 2. Password Input your Password supplied by ISP. 3. Service Name Input the service name supplied by ISP. 4. Connection Type It has three types: Continuous, Connect on Demand, and Manual. 5. Idle Time It is the time of inactivity before disconnecting your PPPoE session. Enter an Idle Time (in minutes) to define a maximum period of time for which the Internet connect is maintained during inactivity. If the connection is inactive for longer than the defined Idle Time, then the connection will be dropped. Either set this to zero or enable Auto-reconnect to disable this feature. 6. MTU Size MTU stands for Maximum Transmission Unit. For PPPoE connection, the default MTU should be provided by computer operating systems (OS). Advanced users can set the MTU manually for increasing the internet performance. The largest number allowed by Ethernet at the network layer is 1492 byte 7. DNS If ISP provides you DNS information, please select Attain DNS automatically, otherwise
http://www.sapido.com.tw 36 USER MANUAL V1.0select Set DNS Manually and input the DNS information into the blank. 8. 3.5G Backup The default interval between the two connection detection is 3 minutes, and the range is from 1 to 60 minutes. Once Internet connection is disconnected, the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none existed. 9. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. 10. Enable IGMP Proxy The Internet Group Management Protocol (IGMP) is a communications protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. You can choose to enable IGMP Proxy to provide service. 11. Enable Ping Access on WAN Select Enable Ping Access on WAN, will make WAN IP address response to any ping request from Internet users. It is a common way for hacker to ping public WAN IP address, to see is there any WAN IP address available. 12. Enable Web Server Access on WAN This option is to enable Web Server Access function on WAN. 13. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4.2.9 WAN Access Type – PPTP If you have applied for a PPTP connection type from ISP, please follow the steps to set up your WAN connection.\
http://www.sapido.com.tw 37 USER MANUAL V1.0
http://www.sapido.com.tw 38 USER MANUAL V1.01. IP Address Input your IP Address supplied by ISP. If you don’t know, please check with your ISP. 2. Subnet Mask Input Subnet Mask, normally it is 255.255.255.0. 3. Server IP Address Input your Server IP Address supplied by ISP. If you don’t know, please check with your ISP. 4. User Name Input the PPTP Account supplied by ISP, for example. If you don’t know, please check with your ISP. 5. Password Input the Password supplied by ISP. 6. MTU Size MTU stands for Maximum Transmission Unit. For PPPoE connection, the default MTU should be provided by computer operating systems (OS). Advanced users can set the MTU manually for increasing the internet performance. The largest number allowed is 1460 byte 7. Request MPPE Encryption Microsoft Point-to-Point Encryption (MPPE) encrypts data in Point-to-Point Protocol (PPP)-based dial-up connections or Point-to-Point Tunneling Protocol (PPTP) virtual private network (VPN) connections. 128-bit key (strong), 56-bit key, and 40-bit key (standard) MPPE encryption schemes are supported. MPPE provides data security for the PPTP connection that is between the VPN client and the VPN server. 8. DNS If ISP provides you DNS information, please select Attain DNS automatically, otherwise select Set DNS Manually and input the DNS information into the blank. 9. 3.5G Backup The default interval between the two connection detection is 3 minutes, and the range is from 1 to 60 minutes. Once Internet connection is disconnected, the system automatically connects Internet via 3.5G adapter. If 3.5G signal is not available, it starts to search downward for 3/2.75/2.5G signals until none existed.
http://www.sapido.com.tw 39 USER MANUAL V1.010. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. 11. Enable IGMP Proxy The Internet Group Management Protocol (IGMP) is a communications protocol used to manage the membership of Internet Protocol multicast groups. IGMP is used by IP hosts and adjacent multicast routers to establish multicast group memberships. You can choose to enable IGMP Proxy to provide service. 12. Enable Ping Access on WAN Select Enable Ping Access on WAN, will make WAN IP address response to any ping request from Internet users. It is a common way for hacker to ping public WAN IP address, to see is there any WAN IP address available. 13. Enable Web Server Access on WAN This option is to enable Web Server Access function on WAN. 14. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4.2.10 LAN Interface Setup Use this page to set up the local IP address and subnet mask for your router. Please select LAN Interface Setup under the IP Config menu and follow the instructions below to enter the LAN setting page to configure the settings you want.
http://www.sapido.com.tw 40 USER MANUAL V1.0 1. Device name The name of device（UPnP name） 2. IP Address The default value of LAN IP address is 192.168.1.1 for this router. 3. Subnet Mask Input Subnet Mask, normally it is 255.255.255.0. 4. Default Gateway Input ISP Default Gateway Address. If you don’t know, please check with your ISP. 5. DHCP Enable or disable DHCP services. The DHCP server will automatically allocate an unused IP address from the IP address pool to the requesting computer if enabled. 6. DHCP Client Range Define the DHCP client range and then the DHCP server will assign an IP to the requesting computer from this range. The Show Client will display every assigned IP address, MAC address, and expired time. The default range is 192.168.1.100 - 192.168.1.200. 7. 802.1d Spanning Tree
http://www.sapido.com.tw 41 USER MANUAL V1.0IEEE 802.1d Spanning Tree Protocol (STP) is a link layer network protocol that ensures a loop-free topology for any bridged LAN. The main purpose of STP is to ensure that you do not create loops when you have redundant paths in your network. Loops are deadly to a network. 8. Clone MAC Address Copy the MAC address from the device you had registered to your ISP if your ISP asks for the specific MAC Address. 9. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4.2.11 Dynamic DNS Setting Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static hostname. Please configure the dynamic DNS below. Please select DDNS under the IP Config menu, and follow the instructions below to enter the DDNS setting page to configure the settings you want. 1. Enable / Disable DDNS Select enable to use DDNS function. Each time your IP address to WAN is changed, and the
http://www.sapido.com.tw 42 USER MANUAL V1.0information will be updated to DDNS service provider automatically. 2. Service Provider Choose correct Service Provider from drop-down list, here including DynDNS, TZO, ChangeIP, Eurodns, OVH, NO-IP, ODS, Regfish embedded in PCI022_MZK-KR150NUS Broadband Router. 3. Domain Name This field represents the host name you register to Dynamic-DNS service and expect to export to the world. 4. User Name /Email User name is used as an identity to login Dynamic-DNS service. 5. Password /Key Password is applied to login Dynamic-DNS service. 6. Apply & Cancel Click on Apply button to continue. Click on Cancel button to clear the setting on this page. 4.3 Wireless Setup PCI022_MZK-KR150NUS Broadband Router enables fastest 150 Mbps IEEE802.11n wireless transmissions and keeps compatibility with existing IEEE 802.11n devices. PCI022_MZK-KR150NUS Broadband Router complies with IEEE 802.11b/g standard. Please select Wireless under the main menu.
http://www.sapido.com.tw 43 USER MANUAL V1.0 4.3.1 Wireless Basic Settings Follow the instructions to configure the Wireless settings.
http://www.sapido.com.tw 44 USER MANUAL V1.0 1. Disable Wireless LAN Interface Select Disable Wireless LAN Interface to turn off the wireless function. 2. Band This field indicates the 802.11x interface mode. For example, “2.4GHz(G)” prevents the 802.11b clients from accessing the router. “2.4GHz(B+G)” allows both 802.11b and 802.11g clients to access the router. There are 6 options, 2.4 GHz (B/G/N/B+G/G+N/B+G+N) from the drop down list. 3. Mode Select AP, WDS, or AP+WDS to allow or disallow the wireless operation. Multiple APs Click Multiple APs to set up 4 different SSIDs to deploy a shared WLAN. Users can add
http://www.sapido.com.tw 45 USER MANUAL V1.0or limit the properties for each SSID, increasing the flexibility and efficiency of the network. (1) Enable: check it for enable or not. (2) Band: select the frequency from the drop down list. (3) SSID: please enter different SSID in each class. (4) Data Rate: please select the data transmission rate. (5) Access: defined the access type. a. LAN+WAN: the client can access to the Internet and connect to PCI022_MZK-KR150NUS Broadband Router’s GUI to setup. b. WAN: the client can only access to the Internet. (6) Active Client List: display the properties of the client which is connecting successfully. (7) Apply Changes: Please click Apply Changes to initiate or click Reset to cancel. 4. Network Type： Please select “Infrastructure” or “Ad hoc.” The default is “Infrastructure.” The selection is disabled when wireless mode is selected to AP. 5. SSID： Please input your wireless network name. Default is “PCI022_MZK-KR150NUS_Broadband_Router”. 6. Channel Width
http://www.sapido.com.tw 46 USER MANUAL V1.0Please select “Auto＂、“20MHZ” or “40MHZ” channel width to change the transmission channels. 7. ControlSideband Setting the Sideband "Upper" or "lower.” 8. Channel Number Please select your wireless network channel. There are Auto, 1~11. 9. Broadcast SSID Enable or disable the SSID broadcast function. Disable this feature can provide more security of your WLAN. 10. Data Rate Rate at which data can be communicated (bps); auto, 1M, 2M, 5.5M, 11M, 6M, 9M, 12M, 18M, 24M, 36M, 48M or 54M to be selected from the drop-down list. 11. Associated Clients Check the WiFi ISP connectors and the connecting status. 12. Enable Mac Clone (Single Ethernet Client) Copy the MAC Address for identity of some ISPs. 13. Enable Universal Repeater Mode (Acting as AP and Client simultaneously) Enable Universal Repeater Mode, PCI022_MZK-KR150NUS Broadband Router will act as a wireless AP and AP client at the same time, and able to link to another AP.. It uses AP client function to connect to a Root AP (any AP) and uses AP function to service all wireless stations within its coverage. All the stations within the coverage of PCI022_MZK-KR150NUS Broadband Router can be bridged to the Root AP. It can help user to extend the coverage of wireless network. How to Enable URM (Universal Repeater Mode) User could enable URM in wireless basic setting page as shown in following figures. Step 1. Get back to menu “Network Config” and write down the SSID, channel and security.
http://www.sapido.com.tw 47 USER MANUAL V1.0 Step 2. Setting the same SSID, channel and security you got form “Network Config” and Click on Apply Changes to save the setting Note: The DHCP server should be disabled under menu “LAN Interface Setup” and then the URM could be enabled. Step 3. Check the AP connectors and the Wireless connecting status. 14. SSID of Extended Interface When mode is set to “AP” and Universal Repeater Mode is enabled, user should input SSID of another AP (the upper level device) in the field of SSID of Extended Interface. 15. Apply Changes & Reset Click on “Apply Changes” to save the setting data. Or you may click on “Reset” to clear all the input data.
http://www.sapido.com.tw 48 USER MANUAL V1.04.3.2 Wireless Advanced Settings Please follow the instructions to configure the Wireless settings. 1. Fragment Threshold To identify the maximum length of packet, the overflow packet length wil be fragmentized. The allowed range is 256-2364, and default length is 2346 bytes. 2. RTS Threshold This value should remain at its default setting of 2347. The range is 0~2347. Should you encounter inconsistent data flow, only minor modifications are recommended. If a network packet is smaller than the present RTS threshold size, the RTS/CTS mechanism will not be enabled. The router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. Fill the range from 0 to 2347 into this blank. 3. Beacon Interval
http://www.sapido.com.tw 49 USER MANUAL V1.0Beacons are packets sent by an access point to synchronize a wireless network. Specify a beacon interval value. The allowed setting range is 20-1024 ms. 4. Preamble Type The preamble (also called “a header”) is a section of data at the head of a packet that contains information that wireless devices need when they send and receive packets. Short preambles improve throughput performance, but some wireless devices require long preambles. Select the suitable preamble as short or long preamble. 5. IAPP Inter Access Point Protocol. Allow seamless roaming between Access Points in your wireless network. Coupled with superior RF performance 6. Protection Select to enable the wireless protection or not. 7. Aggregation Data aggregation can reduce the amount of data routed through the network, and increasing throughput. 8. Short GI Enabling the Short Guard Interval increases the wireless transmission. 9. RF Output Power User can adjust the RF output power to get the best wireless connection. There are 5 power types available: 100%, 70%, 50%, 35%, and 15%. 10. Apply Changes & Reset Click on “Apply Changes” to save the setting data. Or you may click on “Reset” to clear all the input data. 4.3.3 Wireless Security Setup 4 encryption types can be selected here, please follow the instructions below for each.
http://www.sapido.com.tw 50 USER MANUAL V1.0 1. Encryption – WEP Enabling WEP can protect your data from eavesdroppers. If you do not need this feature, select “None” to skip the following setting. PCI022_MZK-KR150NUS Broadband Router supports both 64-bit and 128-bit encryption using the Wired Equivalent Privacy (WEP) algorithm. Select the type of encryption you want to use (64 or 128 bit) and configure one to four WEP Keys. The “1280bit” method is more secure than the “64-bit”. 2. Use 802.1x Authentication Enable 802.1x Authentication so that a wireless node must be authenticated before it
http://www.sapido.com.tw 51 USER MANUAL V1.0can gain access to other LAN resources. Key Length: For 64bits WEP key, either 5 ASCII characters or 10 hexadecimal digitals leading by 0x can be entered. For 128bits WEP key, either 13 ASCII characters or 26 hexadecimal digits leading by 0x can be entered. Note: 128 bits WEP is most secure, but has more encryption/decryption overhead. Note that all wireless devices must support the same WEP encryption bit size and have the same key. Four keys can be entered here, but only one key can be selected at a time. The keys can be entered in ASCII or Hexadecimal. Select the item from drop-down list you wish to use. Encryption Key: At most four keys can be set. A WEP key is either 10 or 26 hexadecimal digits (0~9, a~f, and A~F) based on whether you select 64 bit or 128 bit in the WEP drop-down list. 3. Encryption – WPA (WPA, WPA2 & WPA Mixed) The WPA, WPA2 & WPA Mixed encrypt each frame transmitted from the radio using the pre-shared key (PSK) which entered from this panel or a key got dynamically through 802.1x. WPA Authentication Mode Enterprise (RADIUS): Please input the port, IP address, and password of authentication RADIUS Server. Personal (Pre-Shared Key): Pre-Shared Key type is coding in ASCII, and the length is between 8 to 63 characters. If the coding is in Hex, the key length is 64 characters.
http://www.sapido.com.tw 52 USER MANUAL V1.04. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4.3.4 Wireless Access Control With the MAC address, you may allow or disallow the access to your AP. 1. Wireless Access Control Mode “Allowed Listed” means only the MAC address listed on the allowed list can access to your wireless network. “Deny Listed” means the listed MAC Address are not allowed to linkto your wireless network. “Disable” for function disuse. 2. MAC Address Please input the allowed or denied MAC address, for example, 001122334455. 3. Comment You may input the comments for the set MAC Address. 4. Apply Changes & Reset
http://www.sapido.com.tw 53 USER MANUAL V1.0Click on “Apply Change” to save the setting data. Or you may click on “Reset” to clear all the input data. 5. Current Access Control List In this list, all the MAC info you input will be displayed. 6. Delete Selected and Delete All Click on “Delete Selected” to erase the selected MAC address. Click on “Delete All” to erase all the entered MAC Address. 4.3.5 WDS Settings WDS (Wireless Distribution System) is a Wireless Access Point mode that enables wireless bridging in which only WDS APs communicate with each other (without allowing for wireless clients or stations to access them), and/or wireless repeating in which APs communicate both with each other and with wireless stations (at the expense of half the throughput). InternetAP RouterWDSAP RouterWDSWireless ConnectionWired Connection Please follow the instructions to setup WDS connections.
http://www.sapido.com.tw 54 USER MANUAL V1.0 Step 1. Check the MAC address and Channel number of the device you want to setup WDS with PCI022_MZK-KR150NUS Broadband Router. Step 2. Get back to the menu “Wireless Basic Settings” of PCI022_MZK-KR150NUS Broadband Router. Select AP+WDS mode, and then select the Channel Number. Click Apply Changes to save the setting data.
http://www.sapido.com.tw 55 USER MANUAL V1.0 Step 3. Enter the WDS Settings page, select Enable WDS, and then input the MAC address of the paired device. Click Apply Changes to save the setting data. Step 4. When the time counts down to 0, you will see the MAC address of the paired device displaying on Current WDS AP List.
http://www.sapido.com.tw 56 USER MANUAL V1.0 Step 5. Head back to LAN Interface, disable DHCP option, and then click Apply Changes to save the setting data. Step 6. Doing the same way to setup the MAC address in the paired device. Launch the UT to the menu “WDS settings” of the paired device, and input router’s MAC address. Click Apply Changes to save the setting data.
http://www.sapido.com.tw 57 USER MANUAL V1.0 Step 7. After initiating the paired device, please check Local Area Connections. Click Supports to check out the IP address which is assigned by the paired device. Step 8. You can input http://192.168.9.9 in IE browser to enter the GUI page of the paired device and make sure the connection. Input the MAC address here.
http://www.sapido.com.tw 58 USER MANUAL V1.0 4.3.6 WPS Wi-Fi Protected Setup (WPS) is an easy way to establish a secured wireless network between PCI022_MZK-KR150NUS Broadband Router and wireless card. Users do not need to manually entering a creative, yet predictable security key on both Wi-Fi devices to prevent unwanted access to their wireless network. With WPS, it can automatically configure a wireless network with a network name (SSID) and strong WPA data encryption and authentication. WPS can be enabled by 2 methods: 1. PBC (Push button configuration) Method, in which the user simply has to push a button, either an actual or a virtual one, on both WPS devices to connect.
http://www.sapido.com.tw 59 USER MANUAL V1.02. PIN (Personal Identification Number) Method, in which a PIN has to be taken either from a sticker label or from the web interface of the WPS device. This PIN will then be entered in the AP or client WPS device to connect. Please follow instructions below to enable the WPS function. Start PBC: (1.) Press the WPS button from PCI022_MZK-KR150NUS Broadband Router or click Start PBC from menu “Wi-Fi Protected Setup”, and waiting for the WPS wireless card setting. or
http://www.sapido.com.tw 60 USER MANUAL V1.0 (2.) Open the “Wireless Utility” of your wireless card, and click its “PBC” button, to start auto pairing. (3.) While scanning is successful, the information of the wireless card appears in the windows below.
http://www.sapido.com.tw 61 USER MANUAL V1.0 Start PIN: (1.) Open the “Wireless Utility” of your wireless card. Follow its PIN instruction to get a new PIN number. Write it down.
http://www.sapido.com.tw 62 USER MANUAL V1.0(2.) Open menu “Wi-Fi Protected Setup” of PCI022_MZK-KR150NUS Broadband Router, input the PIN number from the wireless card then click Start PIN. (3.) Back to “Wireless Utility” and press the “Start PIN” button to complete the auto-paring process. Enter the PIN Code you got from the wireless card.
http://www.sapido.com.tw 63 USER MANUAL V1.0 4.4 NAT NAT is a method of mapping one or more IP addresses and/or services ports into different specified services, where NAT stands for Network Address Translation. It allows the internal IP addresses of many computers on a Local Area Network (LAN) to be translated to one public address, saving users’ cost. It also plays a security role by obscuring the true IP addresses of important machines from potential hackers on the Internet. For convenience, we called a router having the NAT facility as a NAT-enabled router. 4.4.1 Visual Server To offer services, like WWW, FTP, provided by a server in your local network accessible for outside users, you should specify a local IP address to the server. Then, add the IP address and network protocol type, port number, and name of the service in the following list. Based on the list, the gateway will forward service request from outside users to the corresponding local server.
http://www.sapido.com.tw 64 USER MANUAL V1.0 1. Enable Port Forwarding Enable Port Forwarding to allow an external user to reach a port within a private LAN. 2. IP Address Specify the private IP address of the internal host offering the service. 3. Protocol Specify the transport layer protocol (TCP or UDP). 4. Public/Private Port Range Enter the Start and End ports in the range you'd like to forward. If you're just forwarding 1 port, set them both equal. For example 80-80 or 20-22。 5. Comment You can add comments for this port forwarding rule. 6. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 7. Current Port Forwarding Table It will display all port forwarding regulation you made. 8. Delete Selected & Delete All
http://www.sapido.com.tw 65 USER MANUAL V1.0Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. 9. Reset You can click Reset to cancel. Port Forwarding The following figure shows the ip forwarding configuration of your web on a local area network. The web server is located on 192.168.1.100, forwarding port is 80, and type is TCP+UDP. 4.4.2 Visual DMZ Virtual DMZ allows you to expose one computer to Internet, so that all inbound packets will be redirected to the computer you set. It is useful while you run some applications that use uncertain incoming ports. Please use it carefully. Configuration: Private IP: 192.168.1.100 Port: 80 - 80 Type: TCP+UDP
http://www.sapido.com.tw 66 USER MANUAL V1.0 1. Enable DMZ Check Enable to apply Virtual DMZ for the Router. 2. DMZ Host IP Address This field stands for the destination IP address that you like to redirect the matched packet to. 3. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4.5 Firewall The Firewall function helps to protect your local network against attacks from outside. It also provides a way of restricting users on the local network from accessing the Internet. Additionally, it can filter out specific packets to trigger the router to place an outgoing connection.
http://www.sapido.com.tw 67 USER MANUAL V1.0 4.5.1 Port Filtering This function allows users to filter and manage specific ports; to limit the use of certain applications to transmit through a specific port. Port filtering helps users to improve the security of your network. 1. Enable Port Filtering Check Enable Port Filtering to start the service. 2. Port Range
http://www.sapido.com.tw 68 USER MANUAL V1.0Enter the Start and End ports in the range you'd like them to be filtered. 3. Protocol Please select the protocol type of the port. 4. Comment You can add comments for this Port Filtering rule. 5. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 6. Current Filter Table It will display all ports that are filtering now. 7. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. 8. Reset You can click Reset to cancel. Port Filtering The following figure shows a user limits some applications to use the 80 port. *All clients inside the local area network can’t open the 80 port through this router. 4.5.2 IP Filtering
http://www.sapido.com.tw 69 USER MANUAL V1.0Use IP Filter to deny LAN IP addresses from accessing the Internet. You can deny specific port numbers or all ports for the specific IP address. 1. Enable IP Filtering Check enable or disable to apply IP Filter function. 2. Local IP Address Please enter the IP address that needs to be filtered. 3. Protocol Please select the protocol type of the IP address. 4. Comment You can add comments for this regulation. 5. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 6. Current Filter Table It will display all IP addresses that are filtering now. 7. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this
http://www.sapido.com.tw 70 USER MANUAL V1.0table. 8. Reset You can click Reset to cancel. 4.5.3 MAC Filtering Use MAC filters to deny LAN computers by their MAC addresses from accessing the Internet. You can manually add a MAC address that is currently connected to PCI022_MZK-KR150NUS Broadband Router. 1. Enable MAC Filtering Check enable or disable to apply MAC Filter function. 2. MAC Address Enter the MAC address manually that you want to filter. 3. Comment You can add comments for this MAC Filtering rule. 4. Apply Changes & Reset Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 5. Current Filter Table
http://www.sapido.com.tw 71 USER MANUAL V1.0It will display all MAC addresses that are filtering now. 6. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. 7. Reset You can click Reset to cancel. 4.5.4 URL Filtering Keyword based URL (Uniform Resource Locator) filtering allows you to define one or more keywords that should not appear in URL’s. Any URL containing one or more of these keywords will be blocked. This is a policy independent feature i.e. it cannot be associated to ACL rules. This feature can be independently enabled / disabled, but works only if firewall is enabled. 1. Enable URL Filtering Check enable or disable to apply URL filter function. 2. URL Address Enter the URL address into this blank to apply filter blocking, example: “www.yahoo.com. 3. Apply Changes & Reset
http://www.sapido.com.tw 72 USER MANUAL V1.0Click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. 4. Current Filter table Shows all filtered URL information. 5. Delete Selected & Delete All Click Delete Selected will delete the selected item. Click Delete All will delete all items in this table. 6. Reset You can click Reset to cancel. Note: URL Filtering cannot work when the Visual Server is enabled. Please disable Visual Server before activate filter. 4.6 System Management PCI022_MZK-KR150NUS Broadband Router provides system management including password changing, upgrade firmware, time setting, user’s account setting and other detail settings. Following is detail explanation for each.
http://www.sapido.com.tw 73 USER MANUAL V1.04.6.1 Change Password Administrator can set or change their password in this section. 1. New Password Enter the new password you want to change. 2. New Password (Confirm) Enter the new password again for confirming. 3. Apply & Cancel Click Apply to continue or Cancel to clear the settings on this page. 4.6.2 Upgrade Firmware There is certain risk while upgrading firmware. Upgrading firmware is not recommended unless the significant faulty is found. You can upgrade the firmware of PCI022_MZK-KR150NUS Broadband Router on this page. Make sure the firmware you want to use is on the local hard drive of the computer. Click Upgrade Firmware to proceed.
http://www.sapido.com.tw 74 USER MANUAL V1.0 1. Update Firmware Click on Browse… button to search your local hard drive and locate the firmware to be used for update. 2. Upload & Reset: Click Upload to upgrade the firmware or Reset to restore to factory default Settings Note: 1. To prevent the firmware upgrading interrupted by other wireless signals and caused failure. We recommend using wired connection to do the upgrading. 2. The upgrade firmware will not remove your previous settings. Reset button: On the back of this router, there is a reset button. If you can not login the administrator page by forgetting your password; or the router has problem you can’t solve. You can push the reset button for 10 seconds with a stick. The router will reboot and all settings will be restored to factory default settings. If the problem still exists, you can visit our web site to see if there is any firmware for download to solve the problem.
http://www.sapido.com.tw 75 USER MANUAL V1.0 4.6.3 Profiles Save To back up the current configuration setting or load the backup data, also you can restore PCI022_MZK-KR150NUS Broadband Router to default setting by this function. 1. Save Settings To File Click on Save button for saving the configuration setting into assigned location. A pop window will show up and ask to save config.dat file. please select the location (Figure
http://www.sapido.com.tw 76 USER MANUAL V1.02), for example: the desktop (Figure 3). Please select the location, for example: the desktop. 2. Load Settings From File
http://www.sapido.com.tw 77 USER MANUAL V1.0Click on “Browse…” button for searching the saving configuration from hard drive, and then click on Upload button to load all the settings into the router. Select the config.dat file. Click Upload to retrieve.
http://www.sapido.com.tw 78 USER MANUAL V1.0 When you see the screen below, the updating is completed. Please click OK to return to the main menu. 3. Reset Setting to Default After you have tried other methods for troubleshooting your network, you may choose to restore PCI022_MZK-KR150NUS Broadband Router to the factory default settings.
http://www.sapido.com.tw 79 USER MANUAL V1.0 When you see the screen below, the resetting is completed. Please click OK and return to the main menu. 4.6.4 Time Zone Setting The System time is the time used by PCI022_MZK-KR150NUS Broadband Router for scheduling services. You can manually set the time or connect to a NTP (Network Time Protocol) server. If a NTP server is set, you will only need to set the time zone. If you manually set the time, you may also set Daylight Saving dates and the system time will automatically adjust on those dates.
http://www.sapido.com.tw 80 USER MANUAL V1.0 1. Current Time Users can input the time manually. 2. Time Zone Select Select your time zone location from the drop-down list. 3. Enable NTP client update Check to enable NTP client update. 4. Automatically Adjust Daylight Saving If you are in daylight saving time area, please enable this item. 5. NTP server Please select the NTP server from the pull-down list, or you can enter the NTP server IP address manually. 6. Apply Changes & Reset & Refresh Please click on Apply Changes to save the setting data. Or you may click on Reset to clear all the input data. Or you may click on Refresh to update the system time on the screen. 7. NTP Server Type & Default NTP Server Choose “General Time Server” and select the NTP Server from the drop-down list or choose “Customized Time Server” and enter the server by manual.
http://www.sapido.com.tw 81 USER MANUAL V1.0 4.6.5 UPnP Setting UPnP (Univsersal Plug and Play) allows users to connect their UPnP-enabled broadband router, printer server and other devices right to the network with zero-configuration, meaning easier setup for installing the device on the network. The automatic discovery feature enables the device to obtain an IP address, present and describe itself to other devices and PCs on the network without having to install drivers, but to configure and use those devices. 1. Enable/Disable UPnP Enabling UPNP, click My Network Places, and user can open the web GUI by just clicking on the Internet Gateway Device icon. 4.6.6 Language Setting PCI022_MZK-KR150NUS Broadband Router provides a user friendly interface in 12 languages. You can create your own language interface by following steps. MZK-KR150NUS
http://www.sapido.com.tw 82 USER MANUAL V1.0Step 1. Select Language: Select your preferred language from the drop down list, for example, Deutsch, and then click Apply Changes. Step 2. When you see the screen with message in your selected language, the Language setup is completed. Note: In order to prevent the incomplete translation, you can press “CTRL+F5” to force reload of the page.
http://www.sapido.com.tw 83 USER MANUAL V1.04.7 Log & Status PCI022_MZK-KR150NUS Broadband Router provides the log list and connection status for user to check. 4.7.1 Network Config Network Configuration shows the firmware version and the connection status of LAN, WAN and Wireless.
http://www.sapido.com.tw 84 USER MANUAL V1.0 4.7.2 Event Log PCI022_MZK-KR150NUS Broadband Router provides system logs for review.
http://www.sapido.com.tw 85 USER MANUAL V1.0 1. Enable Log Select Enable Log to record the system log 2. system all, wireless & DoS Select Wireless, DoS or system all to record 3. Enable Remote Log You may choose to enable the remote event log or not. 4. Log Server IP Address Please input the log server IP Address. 5. Apply Changes & Refresh & Clear Click on Apply Changes to save the setting data. Click on Refresh to renew the system time, or on Clear to clear all the record. After clicking Apply Changes to record the event log, it will be shown as the example
http://www.sapido.com.tw 86 USER MANUAL V1.0below. 4.8 Logout Click Logout on the bottom menu to exit and go back to GUI login home page.
http://www.sapido.com.tw 87 USER MANUAL V1.0Chapter 5 AP mode Make sure to shift the mode into AP Mode. When this product is used as an access point, the IP address has to be changed. The default IP under AP mode is 192.168.1.254. 1. Open a Web browser, and enter http://192.168.1.254 (Default Gateway) into the blank. 2. Enter the User name and Password in to the blank and then Click Login. The default values for User Name and Password are admin (all in lowercase letters). Select LAN under the IP Config menu
http://www.sapido.com.tw 88 USER MANUAL V1.0 Item Description Device Name Input a name for this router. IP Address The default IP address is 192.168.1.254 Subnet Mask Enter the Subnet Mask address Default Gateway Enter the Default Gateway address for LAN interfaces DHCP Select DHCP type: Client, Disable, or Server under different environment. DHCP Client Range When enable DHCP server, you can fill in the start and end IP address; client will be assigned an IP address from the range. 802.1d Spanning Tree Disable or Enable the 802.1d Spanning Tree Protocol (STP) Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data.
http://www.sapido.com.tw 89 USER MANUAL V1.0 Chapter 6 WiFi AP mode Make sure to shift the mode into WiFi AP Mode. The default gateway is http://192.168.1.254 and for User Name and Password are admin (all in lowercase letters). Click Login to enter.
http://www.sapido.com.tw 90 USER MANUAL V1.0 Item Description Device Name Input a name for this router. IP Address The default IP address is 192.168.1.254 Subnet Mask Enter the Subnet Mask address Default Gateway Enter the Default Gateway address for LAN interfaces DHCP Select DHCP type: Client, Disable, or Server under different environment. DHCP Client Range When enable DHCP server, you can fill in the start and end IP address; client will be assigned an IP address from the range. 802.1d Spanning Tree Disable or Enable the 802.1d Spanning Tree Protocol (STP) Clone Mac Address Some ISPs require MAC address registration. In this case, enter the MAC address registered to the provider to "Clone MAC Address" Apply Change & Reset Click on Apply Change to save the setting date, or you may click on Reset to clear all the input data. Chapter 7 DDNS Service Application
http://www.sapido.com.tw 91 USER MANUAL V1.0DDNS is a service changes the dynamic IP to the static IP. The settings of DDNS can solve the problem of being given the different IP by router every time. After setting the Router, your host name would correspond to your dynamic IP. Moreover, via the host name application, it could be easier for you to use FTP, Webcam and Printer remotely. Dynamic DNS allows you to make an assumed name as a dynamic IP address to a static host name. Please configure the dynamic DNS below. Please select Dynamic DNS under the IP Config folder, and follow the instructions below to enter the Dynamic DNS page to configure the settings you want. If you don’t have a DDNS account, please follow the steps to complete your DDNS with Dynamic IP settings. Step 1. First access the Internet and fill http://www.dyndns.com/ into the address field of your web browser, then click Create Account.
http://www.sapido.com.tw 92 USER MANUAL V1.0Step 2. Fill in the form as required, and then click on Create Account button.
http://www.sapido.com.tw 93 USER MANUAL V1.0Step 3. When you got this account created message, close it, and check your mailbox. You would get a mail from DynDNS website. Step 4. Click on the indicated address within your mail to confirm. Step 5. Click on login.
http://www.sapido.com.tw 94 USER MANUAL V1.0Step 6. Click Add New Hostname. Step 7. Put in your favorite hostname and service type, and then click Create Host after finished.
http://www.sapido.com.tw 95 USER MANUAL V1.0 Step 8. Your hostname has been created when you see the following page.
http://www.sapido.com.tw 96 USER MANUAL V1.0Step 9. Click “Activate Service”
http://www.sapido.com.tw 97 USER MANUAL V1.0Chapter 8 Q & A 8.1 Installation 1. Q: Where is the XDSL Router installed on the network? A: In a typical environment, the Router is installed between the XDSL line and the LAN. Plug the XDSL Router into the XDSL line on the wall and Ethernet port on the Hub (switch or computer). 2. Q: Why does the throughput seem slow? A: To achieve maximum throughput, verify that your cable doesn’t exceed 100 meter. If you have to do so, we advise you to purchase a bridge to place it in the middle of the route in order to keep the quality of transmitting signal. Out of this condition you would better test something else. z Verify network traffic does not exceed 37% of bandwidth. z Check to see that the network does not exceed 10 broadcast messages per second. z Verify network topology and configuration. 8.2 LED 1. Why doesn’t PCI022_MZK-KR150NUS Broadband Router power up? A: Check if the output voltage is suitable, or check if the power supply is out of order. 2. The Internet browser still cannot find or connect to PCI022_MZK-KR150NUS Broadband Router after verifying the IP address and LAN cable, the changes cannot be made, or password is lost. A: In case PCI022_MZK-KR150NUS Broadband Router is inaccessible, you can try to restore its factory default settings. Please press the “Reset” button and keep it pressed for over 10 seconds and the light of STATUS will vanish. The LEDs will flash again when reset is successful. 3. Why does PCI022_MZK-KR150NUS Broadband Router shut down unexpectedly? A: Re-plug your power adapter. Then, check the STATUS indicator; if it is off, the internal flash memory is damaged. For more help, please contact with your provider.
http://www.sapido.com.tw 98 USER MANUAL V1.08.3 IP Address 1. Q: What is the default IP address of the router for LAN port? A: The default IP address is 192.168.1.1 with subnet mask 255.255.255.0 2. Q: I don't know my WAN IP. A: There are two ways to know. Way 1: Check with your Internet Service Provider. Way 2: Check the setting screen of PCI022_MZK-KR150NUS Broadband Router. Click on Status & Log item to select Network Configuration on the Main Menu. WAN IP is shown on the WAN interface. 3. How can I check whether I have static WAN IP Address? A: Consult your ISP to confirm the information, or check Network Configuration in PCI022_MZK-KR150NUS Broadband Router’s Main Menu. 4. Will the Router allow me to use my own public IPs and Domain, or do I have to use the IPs provided by the Router? A: Yes, the Router mode allows for customization of your public IPs and Domain. 8.4 OS Setting 1. Why can’t my computer work online after connecting to PCI022_MZK-KR150NUS Broadband Router? A: It’s possible that your Internet protocol (TCP/IP) was set to use the following IP address. Please do as the following steps. (Windows 2000 & XP) Start＞Settings＞Network and Dial-up Connections＞double click on Internet Protocol(TCP/IP)＞select obtain IP address automatically＞ Click on OK button. Then, open Internet browser for testing. If you still can’t go online, please test something else below. z Verify network configuration by ensuring that there are no duplicate IP addresses. z Power down the device in question and ping the assigned IP address of the device. Ensure no other device responds to that address. 1. Check that the cables and connectors or use another LAN cable.
http://www.sapido.com.tw 99 USER MANUAL V1.02. Q: Web page hangs, corrupt downloads, or nothing but junk characters is being displayed on the screen. What do I need to do? A: Force your NIC to 10Mbps or half duplex mode, and turn off the "Auto-negotiate" feature of your NIC as a temporary measure. (Please look at the Network Control Panel, in your Ethernet Adapter's Advanced Properties tab.) 3. Q: Why can't I connect to the Web Configuration? A: you can remove the proxy server settings in your web browser. 8.5 PCI022_MZK-KR150NUS Broadband Router Setup 1. Q: Why does PCI022_MZK-KR150NUS Broadband Router’s setup page shut down unexpectedly? A: If one of the pages appears incompletely in PCI022_MZK-KR150NUS Broadband Router’s setup pages, please click on Logout item on the Main Menu before shutting it down. Don’t keep it working. Then, close Internet browser and open it again for going back to the previous page. 2. Q: Why can’t my USB devices and LAN ports work properly after setting the DHCP? A: There are two rules over here. Rule1: After connecting USB devices, please reboot your Router. Rule2: Before finishing the DHCP setup, please don’t connect any computer to LAN ports, because the conflict of having the same IP may occur and cause some computers a lot of trouble. ※Notice: Make sure that you always click on the Apply button after configuring each setting. And in order to let other LAN ports work properly, please reboot your PC. 3. Q: I don’t know how to configure DHCP. A: DHCP is commonly used in the large local network. It allows you to manage and distribute IP addresses from 2 to 254 throughout your local network via PCI022_MZK-KR150NUS Broadband Router. Without DHCP, you would have to configure each computer separately. It’s very troublesome. Please Open Internet browser > Input 192.168.1.1 in the website blank field > Select DHCP Server
http://www.sapido.com.tw 100 USER MANUAL V1.0under the IP Config Menu. For more information, please refer to Router Mode or AP Mode. 4. Q: How do I upgrade the firmware of PCI022_MZK-KR150NUS Broadband Router? A: Periodically, a new Flash Code is available for PCI022_MZK-KR150NUS Broadband Router on your product supplier’s website. Ideally, you should update PCI022_MZK-KR150NUS Broadband Router’s Flash Code using Upgrade Firmware on the System Management menu of PCI022_MZK-KR150NUS Broadband Router Settings. 5. Q: My PCI022_MZK-KR150NUS Broadband Router cannot connect to the ISP? A: There are three possible solutions. 1. Check the Cable/XDSL modem is power on. 2. Check the Cable/XDSL link light is on to verify a good physical connection. 3. Check the WAN port LED to verify if the Cable/XDSL modem is connected to the router: If your ISP Login method is following, please make sure the username and password are correct or not. If your ISP is using dynamic IP addressing (DHCP) then the DHCP protocol does not have the authentication feature. Some Cable service providers often use the following to determine user’s identification. 6. Q: Why is that I can ping to outside hosts, but cannot access Internet websites? A: Check the DNS server settings on your PC. You should get the DNS servers settings from your ISP. If your PC is running a DHCP client, remove any DNS IP address setting. As the router assign the DNS settings to the DHCP-client-enabled PC. 7. Q: PCI022_MZK-KR150NUS Broadband Router couldn’t save the setting after click on Apply button? A: PCI022_MZK-KR150NUS Broadband Router will start to run after the setting finished applying, but the setting isn’t written into memory. Here we suggest if you want to make sure the setting would be written into memory, please reboot the device via Reboot under System Management directory.
http://www.sapido.com.tw 101 USER MANUAL V1.08.6 Wireless LAN 1. Q: Why couldn’t my wireless notebook work on-line after checking? A: Generally, Wireless networks can sometimes be very complicated to set up, particularly if you're dealing with encryption and products from different vendors. Any number of variables can keep your workstations from talking to each other. Let's go over some of more common ones. For starters, verify that your router and your workstation are using the same SSID descriptions. SSID acts as a password when a mobile device tries to connect to the wireless network. The SSID also differentiates one WLAN from another, so all access points and all devices attempting to connect to a specific WLAN must use the same SSID. A workstation will not be permitted to connect to the network unless it can provide this unique identifier. This is similar to the function of your network's Workgroup or Domain name. When you're experiencing conductivity problems, it is always best to keep things simple. So next you are going to do is that, please disable any WEP encryption you might have configured. Successful implementation of encryption also includes the use of a shared key. A HEX key is the most common, but other formats are also used. This key identifies the workstation to the router as a trusted member of this network. Different manufacturers can implement this key technology in ways that might prevent them from working correctly with another vendor's products. So pay attention to detail is going to be the key to a successful installation. Next make sure the router and the NIC are configured to use the same communications channel. There are normally 11 of them, and the default channel can also vary from vendor to vendor. You might also want to confirm that the router has DHCP services enabled and an address pool configured. If not, the NIC won't be able to pick up an IP address. I have run across a few access points that offer DHCP services but do not assign all of the needed IP information to the NIC. As a result, I was able to connect to the network, but could not browse the web. The point is, don't assume anything. Verify for yourself that all of the required settings are being received by the workstation. Finally, you might want to keep the system you're trying to configure in the same room as the router, at least during the initial configuration, in order to minimize potential interference from concrete walls or steel beams.
http://www.sapido.com.tw 102 USER MANUAL V1.02. Q: My PC can’t locate the Wireless Access Point. A: Check the following: z Your PC is set to Infrastructure Mode. (Access Points are always in Infrastructure Mode.) z The SSID on your PC and the Wireless Access Point are the same. Remember that the SSID is case-sensitive. So, for example “Workgroup” does NOT match “workgroup”. z Both your PC and the Wireless Access Point must have the same setting for WEP. The default setting for the Wireless Router is disabled, so your wireless station should also have WEP disabled. z If WEP is enabled on the Wireless Router, your PC must have WEP enabled, and the key must match. z If the Wireless Router’s Wireless screen is set to Allow LAN access to selected Wireless Stations only, then each of your Wireless stations must have been selected, or access will be blocked. z To see if radio interference is causing a problem, see if connection is possible when close to the Wireless Access Point. Remember that the connection range can be as little as 100 feet in poor environments. 3. Q: Wireless connection speed is very slow. A: The wireless system will connect at highest possible speed, depending on the distance and the environment. To obtain the highest possible connection speed, you can experiment with following: z Access Point location: Try adjusting the location and orientation of the Access Point. z Wireless Channel: If interference is the problem, changing to another channel may show a marked improvement. z Radio Interference: Other devices may be causing interference. You can experiment by switching other devices off, and see if this helps. Any “noisy” devices should be shielded or relocated. z RF Shielding: Your environment may tend to block transmission between the wireless stations. This will mean high access speed is only possible when close to the Access Point. 4. Q: Some applications do not run properly when using the Wireless Router.
http://www.sapido.com.tw 103 USER MANUAL V1.0A: The Wireless Router processes the data passing through it, so it is not transparent. Use the Special Application feature to allow the use of Internet applications which do not function correctly. If this does solve the problem, you can use the DMZ function. This should work with almost every application, but: z It is a security risk, since the firewall is disabled. z Only one (1) PC can use this feature. 5. Q: I can’t connect to the Wireless Router to configure it. A: Check the following: z The Wireless Router is properly installed, LAN connections are OK, and it is powered ON. z Make sure that your PC and the Wireless Router are on the same network segment. z If your PC is set to “Obtain an IP Address automatically” (DHCP client), restart it. z If your PC uses a Fixed (Static) IP address, make sure that it is using an IP Address within the range 192.168.1.129 to 192.168.1.253 and thus compatible with the Wireless Router’s default IP Address of 192.168.1.254. Also, the Network Mask should be set to 255.255.255.0 to match the Wireless Router. In Windows, you can check these settings by using Control Panel ~ Network to check the Properties for the TCP/IP protocol. 6. Q: The WinXP wireless interface couldn’t communicate the WEP with PCI022_MZK-KR150NUS Broadband Router’s wireless interface. A: The default WEP of WinXP is Authentication Open System - WEP, but the WEP of PCI022_MZK-KR150NUS Broadband Router is only for Shared Key - WEP, it caused both sides couldn’t communicate. Please select the WEP of WinXP from Authentication Open System to Pre-shared Key - WEP, and then the WEP wireless interface between WinXP and PCI022_MZK-KR150NUS Broadband Router would be communicated. 8.7 Support 1. Q: What is the maximum number of IP addresses that the XDSL Router will support? A: The Router will support to 253 IP addresses with NAT mode. 5. Q: Is the Router cross-platform compatible?
http://www.sapido.com.tw 104 USER MANUAL V1.0A: Any platform that supports Ethernet and TCP/IP is compatible with the Router. 8.8 Others 1. Q: Why can’t I receive corrupted FTP downloads? A: If you are experiencing corrupted files when you download a file with your FTP client, try using another FTP program. 2. Q: Why does the router dial out for PPPoE mode very often? A: Normally some of game, music or anti-virus program will send out packets that trigger the router to dial out, you can close these programs. Or you can set the idle time to 0, then control to dial out manually. 3. Q: What can I do if there is already a DHCP server in LAN? A: If there are two DHCP servers existing on the same network, it may cause conflict and generate trouble. In this situation, we suggest to disable DHCP server in router and configure your PC manually. 8.9 USB Device 1. Q: How many USB devices can be connected to the Product? A: PCI022_MZK-KR150NUS Broadband Router supports maximum of 1 USB ports.
http://www.sapido.com.tw 105 USER MANUAL V1.0Chapter 9 Appendices 9.1 Operating Systems 1. Microsoft：Windows 2000, XP, Vista 32bit and the following related versions. 2. Apple：Mac OS X 10.4.7, Leopard and the following related versions. 3. Linux：Redhat 9, Fedora 6 & 7, Ubuntu 7.04 and the following related versions. 9.2 Browsers 1. Internet Explorer ver. 6 and 7 and the following related versions. 2. FireFox ver. 2.0.0.11 and the following related versions.3. 3. Safari ver. 3.04 and the following related versions. 9.3 Communications Regulation Information Should any consumers need to learn more information, services and supports, please contact the supplier of your product directly.

Navigation menu