Pismolabs Technology P1375 Pepwave / Peplink / Pismo Wireless Product User Manual Pepwave MAX

Pismo Labs Technology Limited Pepwave / Peplink / Pismo Wireless Product Pepwave MAX

Contents

User Manual (2 of 2).pdf

http://www.pepwave.com 73 Copyright @ 2014 Pepwave 13 Management of Outbound Traffic to WAN The Pepwave MAX provides the functionality to flexibly manage and load balance outbound traffic among the WAN connections. Important Note Outbound Policy is applied only when more than one WAN connection is active. The settings for managing and load balancing outbound traffic are located in Advanced> Outbound Policy: Network > Outbound Policy> Click on
http://www.pepwave.com 74 Copyright @ 2014 Pepwave 13.1 Outbound Policy There are three main selections for the Outbound Policy for the Pepwave MAX:  High Application Compatibility  Normal Application Compatibility  Custom The selections are explained as follows: Outbound Policy Settings High Application Compatibility With the selection of this policy, outbound traffic from a source LAN device is routed through the same WAN connection regardless of the destination Internet IP address and protocol. This provides the highest application compatibility. Normal Application Compatibility With the selection of this policy, outbound traffic from a source LAN device to the same destination Internet IP address will persistently be routed through the same WAN connection regardless of protocol. This provides high compatibility to most applications, and users still benefit from WAN link load balancing when multiple Internet servers are accessed. Custom With the selection of this policy, outbound traffic behavior can be managed by defining custom rules. Rules can be defined in a custom rule table. A default rule can be defined for connections that cannot be matched with any one of the rules. The default policy is Normal Application Compatibility. Tip Want to know more about how-to create outbound rules? Visit our YouTube Channel for a video tutorial! http://youtu.be/rKH4AS_bQnE
http://www.pepwave.com 75 Copyright @ 2014 Pepwave 13.2 Custom Rules For Outbound Policy Click in the Outbound Policy form. Choose Managed by Custom Rules and press the Save button. The followingscreen will then be displayed. The bottom-most rule is Default. Edit this rule to change the device’s default way to control outbound traffic for all connections that does not match any rules above it. Click on the service nameDefaultto change its settings. You may drag and drop a row to rearrange the priority of outbound rules. By default, Auto is selected for the option Default Rule. You can select Custom in order to change the Algorithm to be used.Please refer to the upcoming sections for the details of the available algorithms. To create a custom rule, click Add Rule at the bottom of the table, and the following window will be displayed:
http://www.pepwave.com 76 Copyright @ 2014 Pepwave New Custom Rule Settings Service Name This setting specifies the name of the custom rule. Enable This setting specifies whether the outbound traffic rule takes effect. With an Enable value of Yes, the rule takes effect: traffic is matched, and actions are taken, by the Pepwave MAX based on the other parameters of the rule. With an Enable value of No, the rule does not take effect and the Pepwave MAX will disregard the other parameters of the rule. Source This setting specifies the source IP Address, IP Network or MAC Address for outbound traffic that matches the rule. Destination This setting specifies the destination IP Address or IP Network or Domain Name for traffic that matches the rule. Domain Name If Domain Name is chosen and a domain name, such as foobar.com, is entered, any outgoing accesses to foobar.com and *.foobar.comwill match this criterion. You may enter a wildcard (.*) at the end of a domain name to match any host with a name having the domain name in the middle. If you enter .*, for example, then www.foobar.com, www.foobar.co.jp, or foobar.co.uk will also match. Placing wildcards in any other position is not supported.
http://www.pepwave.com 77 Copyright @ 2014 Pepwave NOTE: if a server has one Internet IP address and multiple server names, and if one of the names is defined here, then accesses to any one of the server names will also match this rule. Protocol and Port This setting specifies the IP Protocol and Port of outbound traffic that matches this rule. You may select some common protocol from the Protocol Selection Tool drop-down menu. Algorithm This setting specifies the behavior of the Pepwave MAX for the custom rule. One of the following values can be selected:  Weighted Balance  Persistence  Enforced  Priority  Overflow  Least Used  Lowest Latency The upcoming sections present the details of the listed algorithms. Terminate Sessions on Link Recovery This setting specifies whether to terminate existing IP sessions on a less preferred WAN connection in the event that a more preferred WAN connection is recovered. This setting is applicable to the Algorithms: Weighted, Persistence and Priority. By default, this is disabled. In this case, all existing IP sessions will not be terminated or affected when any other WAN connection is recovered. If it is set to enabled, existing IP sessions may be terminated when another WAN connection is recovered such that only the preferred healthy WAN connection(s) are used at any point in time.
http://www.pepwave.com 78 Copyright @ 2014 Pepwave 13.2.1 Algorithm: Weighted Balance This setting specifies the ratio of WAN connection usage to be applied on the specified IP Protocol & Port, and is applicable only when Algorithm is set to Weighted Balance. The amount of matching traffic that is distributed to a WAN connection is proportional to the weight of the WAN connection relative to the total weight. Use the sliders to change the weight for each WAN. Example: With the following weight settings:  Ethernet WAN1: 10  Ethernet WAN2: 10  Wi-Fi WAN: 10  Cellular 1: 10  Cellular 2: 10  USB: 10 Total weight is 60 = (10 +10 + 10 + 10 + 10 + 10) Matching traffic distributed to Ethernet WAN1 is 16.7% = (10 / 60 x 100% Matching traffic distributed to Ethernet WAN2 is 16.7% = (10 / 60) x 100% Matching traffic distributed to Wi-Fi WAN is 16.7% = (10 / 60) x 100% Matching traffic distributed to Cellular 1 is 16.7% = (10 / 60) x 100% Matching traffic distributed to Cellular 2 is 16.7% = (10 / 60) x 100% Matching traffic distributed to USB is 16.7% = (10 / 60) x 100%
http://www.pepwave.com 79 Copyright @ 2014 Pepwave 13.2.2 Algorithm: Persistence The Persistencealgorithm is the solution to the few situations where link load distribution for Internet services is undesirable. For example,many e-banking and other secure websites, for security reasons, terminate the session when the client computer’s Internet IP address changes during the session. In general, different Internet IP addresses represent different computers. The security concern is that an IP address change during a session may be the result of an unauthorized intrusion attempt. Therefore, to prevent damages from the potential intrusion, the session is terminated upon the detection of an IP address change. The Pepwave MAX can be configured to distribute data traffic across multiple WAN connections. Also, the Internet IP depends on the WAN connections over which communication actually takes place. As a result, a LAN client computer behind thePepwave MAX may communicate using multiple Internet IP addresses. For example, a LAN client computer behind a Pepwave MAX with three WAN connections may communicate on the Internet using three different IP addresses. With the algorithm Persistence of the Pepwave MAX, rules can be configured to enable client computers to persistently utilize the same WAN connections for e-banking and other secure websites. As a result, a client computer will communicate with the other end using one IP address and eliminate the issues. There are two modes for Persistence: By Source and By Destination. By Source The same WAN connection will be used for traffic matching the rule and originating from the same machine regardless of its destination. This option will provide the highest level of application compatibility. By Destination The same WAN connection will be used for traffic matching the rule, originating from the same machine, and going to the same destination. This option can better distribute load to WAN connections when there are only a few client machines. The default mode is By Source. When there are multiple client requests, they can be distributed (persistently) to WAN connections with a weight. If you choose Autofor Load Distribution, the weights will be automatically adjusted according to each WAN’s Downstream Bandwidth which is specified in the WAN settings page (see Section 8.2Captive Portal The Captive Portal serves as gateway that clients have to pass if they wish to access the internet using your router. To configure, navigate to Network >Captive Portal to see the following screen:
http://www.pepwave.com 80 Copyright @ 2014 Pepwave Captive Portal Settings Apply On Clicking the edit button trigger a dialogue where you can choose which LAN / VLAN to apply your captive portal. Click all LAN / VLAN that you wish to apply the captive portal to. Access Mode Click Open Access to allow clients to freely access your router. Click User Authentication to force your clients to authenticate before accessing your router. Radius Server This authenticates your clients through a Radius Server. Upon selecting this option, you will see the following fields: Fill in the necessary information to complete your connection to the server and enable authentication. LDAP Server This authenticates your clients through a LDAP Server. Upon selecting this option, you will see the following fields: Fill in the necessary information to complete your connection to the server and enable authentication. Access Quota Set a time and data cap to each user’s Internet usage.
http://www.pepwave.com 81 Copyright @ 2014 Pepwave Quota Reset Time This menu determines how your usage quota resets. Setting it to daily will reset it at a specified time every day. Setting a number of minutes after quota reached establish a timer for each user that begins after the quota has been reached. Splash Page Here, you can choose between using the MAX router’s built-in captive portal and redirecting clients to a URL you define. The Portal Customization menu has two options: and . Clicking will result in a pop-up previewing the captive portal that your clients will see. Clicking will result in the appearance of following menu: Portal Customization Logo Image Click the Choose File button to select an logo to use for the built-in portal
http://www.pepwave.com 82 Copyright @ 2014 Pepwave Message If you have any additional messages for your users, place it on this field. Terms & Conditions If you would like to use your own set of terms and conditions, please place it here. If left empty, the built-in portal will display the default terms and conditions. Custom Landing Page Fill in this field to redirect clients to an external URL.
http://www.pepwave.com 83 Copyright @ 2014 Pepwave 14 Configuration of WAN Interface(s) ). If you choose Custom, you can customize the weight of each WAN manually by using the sliders.
http://www.pepwave.com 84 Copyright @ 2014 Pepwave 14.1.1 Algorithm: Enforced This setting specifies the WAN connection usage to be applied on the specified IP Protocol & Port, and is applicable only when theAlgorithm is set to Enforced. Matching traffic will be routed through the specified WAN connection regardless of the connection’s health check status. Starting from firmware 5.2, outbound traffic can be enforced to go through a specified SpeedFusionTM connection. 14.1.2 Algorithm: Priority This setting specifies the priority of the WAN connections to be utilized to route the specified network service. The highest priority WAN connectionavailable will always be used for routing the specified type of traffic. A lower priority WAN connection will be used only when all higher priority connections have become unavailable. Starting from firmware 5.2, outbound traffic can be prioritized to go through SpeedFusionTMconnection(s). By default, VPN connections are not included in the priority list. Tip Configure multiple distribution rules to accommodate different kinds of services.
http://www.pepwave.com 85 Copyright @ 2014 Pepwave 14.1.3 Algorithm: Overflow The traffic matching this rule will be routed through the healthy WAN connection that has the highest priority and is not in full load. When this connection gets saturated, new sessions will be routed to the next healthy WAN connection that is not in full load. Drag and drop to specify the order of WAN connections to be used for routing traffic. Only the highest priority healthy connection that is not in full load will be utilized. 14.1.4 Algorithm: Least Used The traffic matching this rule will be routed through the healthy WAN connection that is selected in the fieldConnectionand has the most available downstreambandwidth. The available downstream bandwidth of a WAN connection is calculated from the total downstream bandwidth specified in the WAN settings page and the current downstream usage. The available bandwidth and WAN selection is determined every time when an IP session is made.
http://www.pepwave.com 86 Copyright @ 2014 Pepwave 14.1.5 Algorithm: Lowest Latency The traffic matching this rule will be routed through the healthy WAN connection that is selected in the field Connection and has the lowest latency. Latency checking packets are issued periodically to a nearby router of each WAN connection to determine its latency value. The latency of a WAN is the packet round trip time of the WAN connection. Additional network usage may be incurred as a result. Tip The round trip time of a “6M down / 640k up” link can be higher than that of a “2M down / 2M up” link. It is because the overall round trip time is lengthened by its lower upstream bandwidth despite of its higher downlink speed. Therefore this algorithm is good for two scenarios: - All WAN connections are symmetric; or - A latency sensitive application requires to be routed through the lowest latency WAN regardless the WAN’s available bandwidth. 14.1.6 Expert Mode Expert Mode is also available for advance users. Click the help test balloon and click the link turn on Expert Mode to switch on the feature. Under Expert Mode, a special rule - "SpeedFusionTMRoutes" is displayed on the Custom Rules table. It represents all SpeedFusionTMroutes learned from remote VPN peers. By default, this bar is on the top of all custom rules. That means traffic for remote VPN subnets will be routed to its corresponding VPN peer. You can create custom Priority or Enforced rules and move them above the bar to override the SpeedFusionTMRoutes. Upon disabling the Expert Mode, all rules above the bar will be deleted.
http://www.pepwave.com 87 Copyright @ 2014 Pepwave 15 Port Forwarding 15.1 Port Forwarding Service The Pepwave MAXcan act as a firewall that blocks, by default, all inbound access from the Internet. By usingPort Forwarding, Internet users can access the servers behind Pepwave MAX. Inbound Port Forwarding rules can bedefined at Advanced>Port Forwarding: To define a new service, click the Add Servicebutton, upon which the following appears: Port Forwarding Settings Enable This setting specifies whether the inbound service rule takes effect. When Yes is selected, the inbound service rule takes effect. If the inbound traffic matches the specified IP Protocol and Port, action will be taken by the Pepwave MAX based on the other parameters of the rule. When No is selected, the inbound service rule does not take effect. The Pepwave MAX will disregard the other parameters of the rule. Service Name This setting identifies the service to the System Administrator. Valid values for this setting consist only of alphanumeric and the underscore “_” characters. IP Protocol The IP Protocol setting, along with the Port setting, specifies the protocol of the service as TCP, UDP, ICMP or IP. Traffic that is received by the Pepwave MAX via the specified protocol at the specified port(s) is forwarded to the LAN hosts specified by the Servers setting. (Please see below for details on the Port and Servers settings.) Alternatively, the Protocol Selection Tool drop-down menu can be used toautomatically
http://www.pepwave.com 88 Copyright @ 2014 Pepwave fill in the Protocol and a single Port number of common Internet services (e.g. HTTP, HTTPS, etc.). After selecting an item from the Protocol Selection Tool drop-down menu, the Protocol and Port number remains manually modifiable. Port The Port setting specifies the port(s) that correspond to the service, and can be configured to behave in one of the following manners: Any Port, Single Port, Port Range and Port Map Any Port: All traffic that is received by the Pepwave MAX via the specified protocol is forwarded to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Any Port, all TCP traffic is forwarded to the configured servers. Single Port: Traffic that is received by the Pepwave MAX via the specified protocol at the specified port is forwarded via the same port to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Single Port and Service Port 80, TCP traffic received on Port 80 is forwarded to the configured servers via Port 80. Port Range: Traffic that is received by the Pepwave MAX via the specified protocol at the specified port range is forwarded via the same respective ports to the LAN hosts specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Single Port and Service Port 80-88, TCP traffic received on ports 80 through 88 is forwarded to the configured servers via the respective ports. Port Mapping: Traffic that is received by the Pepwave MAX via the specified protocol at the specified port is forwarded via a different port to the servers specified by the Servers setting. For example, with IP Protocol set to TCP, and Port set to Port Map, Service Port 80, and Map to Port 88, TCP traffic on Port 80 is forwarded to the configured servers via Port 88. (Please see below for details on the Servers setting.) Range Mapping: traffic that is received by the Pepwave MAX via the specified protocol at the specified port range is forwarded via a different port to the servers specified by the Servers setting. Inbound IP Address(es) This setting specifies the WAN connections and Internet IP address(es) from which the service can be accessed. It is required to select at least one IP address. Server IP Address This setting specifies the LAN IP address of the server that handles the requests for the service.
http://www.pepwave.com 89 Copyright @ 2014 Pepwave 15.1.1 UPnP / NAT-PMP Settings UPnP and NAT-PMP are network protocols which allow a computer on the LAN to automatically configure the router to allow parties on the WAN to connect to itself.In this way, the process of inbound port forwarding is automated. When a computer creates a rule using these protocols, the specified TCP/UDP port of all WAN connections' default IP address will be forwarded. Check the corresponding box(es) to enable UPnP and/or NAT-PMP. Enable these features only if you trust the computers on the LAN. A table listing all the forwarded ports under these two protocols can be found at Status > UPnP / NAT-PMP.
http://www.pepwave.com 90 Copyright @ 2014 Pepwave 16 NAT Mappings The configuration of NAT Mappings allows the IP address mapping of all inbound and outbound NAT’dtraffic to and from an internal client IP address. The settings to configure NAT Mappings are located at Advanced>NAT Mappings: To add a rule for NAT Mappings, click Add NAT Rule, upon which the following screen will be displayed: NAT Mapping Settings LAN Client(s) NAT Mapping rules can be defined for a single LAN IP Address, an IP Range, or an IP Network. Address This refers to the LAN host’s private IP address. The system maps this address to a number of public IP addresses, specified below, in order to facilitate inbound and outbound traffic. This option is only available when IP Address is selected. Range The IP range is a contiguous group of private IP addresses used by the LAN host. The system maps these addresses to a number of public IP addresses, specified below, to facilitate outbound traffic. This option is only available when IP Range is selected.
http://www.pepwave.com 91 Copyright @ 2014 Pepwave Network The IP network refers to all private IP addresses and ranges managed by the LAN host. The system maps these addresses to a number of public IP addresses, specified below, to facilitate outbound traffic. This option is only available when IP Network is selected. Inbound Mappings This setting specifies the WAN connections and corresponding WAN-specific Internet IP addresses on which the system should bind on. Any access to the specified WAN connection(s) and IP address(es) will be forwarded to the LAN Host. This option is only available when IP Address is selected in LAN Client(s) field. Note 1: Inbound Mapping is not needed for WAN connections in drop-in or IP forwarding mode. Note 2: Each WAN IP address can be associated to one NAT Mapping only. Outbound Mappings This setting specifies the WAN IP addresses should be used when an IP connection is made from a LAN host to the Internet. Each LAN host in an IP range or IP network will be evenly mapped to one of each selected WAN's IP addresses (for better IP address utilization) in a persistent manner (for better application compatibility). Note 1: If you do not want to use a specific WAN for outgoing accesses, you should still choose default here, then customize the outbound access rule in the Outbound Policy section. Note 2: WAN connections in drop-in or IP forwarding mode are not shown here. Important Note Inbound firewall rules override the Inbound Mapping settings.
http://www.pepwave.com 92 Copyright @ 2014 Pepwave 17 QoS 17.1 User Groups LAN and PPTP clients can be categorized into three user groups - Manager, Staff, and Guest. This table allows you to define rules and assign client IP addresses or subnets to a user group. You can apply different bandwidth and traffic prioritization policies on each user group in the Bandwidth Control and Application sections. The table is automatically sorted, and the table order signifies the rules' precedence.The smaller and more specific subnets are put towards the top of the table and have higher precedence; larger and less specific subnets are placed towards the bottom. Click the Add button to define clients and their user group. Click the button to remove the defined rule. Two default rules are pre-defined and put at the bottommost. They are All DHCP reservation clients and Everyone, and they cannot be removed. All DHCP reservation clients represents the LAN clients defined in the DHCP Reservation table in the LAN settings page. Everyone represents all clients that are not defined in any rule above. Click on a rule to change its group. Add / Edit User Group Subnet / IP Address From the drop-down menu, choose whether you are going to define the client(s) by an IP Address or a Subnet. If IP Address is selected, enter a name defined in DHCP Reservation table or a LAN client's IP address. If Subnet is selected, enter a subnet address and specify its subnet mask. Group This field is to define which User Group the specified Subnet / IP Address belongs to. Once users have been assigned to a user group, their Internet traffic will be restricted by rules defined for that particular group. Please refer to the following two sections for details.
http://www.pepwave.com 93 Copyright @ 2014 Pepwave 17.2 Bandwidth Control You can define a maximum download speed (over all WAN connections) and upload speed (for each WAN connection) that each individual Staff and Guest member can consume. No limit can be imposed on individual Manager members. By default, Download and Upload Bandwidth Limits are set to unlimited (set as 0).
http://www.pepwave.com 94 Copyright @ 2014 Pepwave 17.3 Application 17.3.1 Application Prioritization You can choose whether to apply the same Prioritization settings to all user groups or customize the settings for each group. Three priority levels can be set for application prioritization: ↑High,━ Normal, and↓Low. Four types of applications are predefined. Their priority for each user group can be selected from their corresponding drop down menu.Traffic types not defined in the table is assigned with normal priority.
http://www.pepwave.com 95 Copyright @ 2014 Pepwave 17.3.2 Prioritization for Custom Application Clickthe Add button to define a custom application. Click the button in the Action column to delete the custom application in the corresponding row. Application Prioritization PPTP and IPsec VPN When enabled, any PPTP and IPsec traffic will be prioritized. SIP/Vonage When enabled, any SIP and Vonage voice traffic will be prioritized. Skype, Google Talk, RealVideo, and Windows Streaming Media When enabled, voice and video traffic of Skype, Google Talk, Real Video and Windows Streaming Media will be prioritized. Secure Web (HTTPS) When enabled, HTTPS (TCP port 443) traffic will be prioritized. 17.3.3 DSL/Cable Optimization DSL/cable-based WAN connection has its upload bandwidth lower than the download bandwidth.When this option is enabled, the download bandwidth of the WAN can be fully utilized in any situation. When a DSL/cable circuit's uplink is congested, the download bandwidth will be affected. Users will not be able to download data in full speed until the uplink becomes less congested.The DSL/Cable Optimization can relieve such issue. When it is enabled, the download speed will become less affected by the upload traffic. By default, this feature is enabled.
http://www.pepwave.com 96 Copyright @ 2014 Pepwave 18 Firewall A firewall is a mechanism that selectively filters data traffic between the WAN side (the Internet) and the LAN side of the network.It can protect the local network from potential hacker attacks, offensive Web sites, and/or other inappropriate uses. The firewall functionality of the Pepwave MAX supports the selective filtering of data traffic in both directions:  Outbound (LAN to WAN)  Inbound (WAN to LAN)  Intrusion Detection and DoS Prevention With SpeedFusionTM enabled (see Section11), the firewall rules also apply to VPN tunneled traffic. 18.1 Outbound and Inbound Firewall 18.1.1 Access Rules The outbound firewall settings are located at:Advanced> Firewall> Outbound Firewall Rule. Upon clickingAdd Rule, the following screen appears:
http://www.pepwave.com 97 Copyright @ 2014 Pepwave Inbound firewall settings are located at: Advanced> Firewall> Inbound Firewall Rule. Once you click on Add Rule, the following window will appear: Rules are matched from top to the bottom.If a connection matches any one of the upper rules, the matching process will stop. If none of the rules is matching, the Defaultrule will be applied. By default, theDefault rule is set as Allow for both outbound and inbound access.
http://www.pepwave.com 98 Copyright @ 2014 Pepwave Inbound / Outbound Firewall Settings Rule Name This setting specifies a name for the firewall rule. Enable This setting specifies whether the firewall rule should take effect. When Yes is selected, the firewall rule takes effect. If the traffic matches the specified Protocol/IP/Port, actions will be taken by the Pepwave MAX based on the other parameters of the rule. When No is selected, the firewall rule does not take effect. The Pepwave MAX will disregard the other parameters of the rule. WAN Connection This setting is applicable to Inbound Firewall Rules only. This setting specifies which WAN connection(s) the rule applies to:  WAN 1  WAN 2  Wi-Fi WAN  Cellular 1  Cellular 2  USB A value ofWAN 1, WAN 2, Wi-Fi WAN, Cellular 1, Cellular 2, … and USB specifies that the rule applies to all WAN connections, Ethernet WAN, PC Card, … and Wi-Fi WAN, respectively. Protocol This setting specifies the protocol to be matched by the rule. Via a drop-down menu, the following protocols can be specified:  TCP  UDP  ICMP  IP Alternatively, the Protocol Selection Tool drop-down menu can be used to automatically fill in the Protocol and Port number of common Internet services (e.g. HTTP, HTTPS, etc.) After selecting an item from the Protocol Selection Tool drop-down menu, the Protocol and Port number remains manually modifiable. Source IP & Port This specifies the source IP address(es) and port number(s) to be matched for a firewall rule. A single address, or a network, can be specified as the Source IP & Port setting, as indicated with the following screenshots: In addition, a single port, or a range of ports, can be specified for the Source IP & Port setting. Destination IP & Port This specifies the destination IP address(es) and port number(s) to be matched for a firewall rule. A single address, or a network, can be specified as the Source IP & Port setting, as indicated with the following screenshots:
http://www.pepwave.com 99 Copyright @ 2014 Pepwave In addition, a single port, or a range of ports, can be specified for the Source IP & Port setting. Action This setting specifies the action to be taken by the Pepwave MAX upon encountering traffic that matches the both of the following:  Source IP & Port  Destination IP & Port  With the value of Allow for the Action setting, the matching traffic passes through the Pepwave MAX (to be routed to the destination).  If the value of the Action setting is set to Deny, the matching traffic does not pass through the Pepwave MAX (and is discarded). Event Logging This setting specifies whether or not to log matched firewall events. The logged messages are shown on the page Status >Event Log. A sample message is as follows: Aug 13 23:47:44 Denied CONN=Ethernet WAN SRC=20.3.2.1 DST=192.168.1.20 LEN=48 PROTO=TCP SPT=2260 DPT=80  CONN: The connection where the log entry refers to  SRC: Source IP address  DST: Destination IP address  LEN: Packet length  PROTO: Protocol  SPT: Source port  DPT: Destination port Tip If the default inbound rule is set as Allow for NAT enabled WANs, no inbound Allow firewall rules will be required for inbound Port Forwarding and inbound NAT Mapping rules. However, if the default inbound rule is set as Deny, a corresponding Allow firewall rules will be required.
http://www.pepwave.com 100 Copyright @ 2014 Pepwave 18.1.1.1 Intrusion Detection and DoS Prevention The Pepwave MAX supports detecting and preventing intrusions and Denial-of-Service (DoS) attacks from the Internet. To turn on this feature, click , check the box Enablefor the Intrusion Detection and DoS Prevention and press the Save button. When this feature is enabled, the Pepwave MAX will detect and protect the network from the following kinds of intrusions and denial-of-service attacks.  Port Scan: o NMAP FIN/URG/PSH o Xmas Tree o Another Xmas Tree o Null Scan o SYN/RST o SYN/FIN  SYN Flood Prevention  Ping Flood Attack Prevention
http://www.pepwave.com 101 Copyright @ 2014 Pepwave 18.1.2 Web Blocking 18.1.2.1 Web Blocking Enter an appropriate website address and the Pepwave MAX will block and disallow LAN/PPTP/SpeedFusionTM peer clients to access these websites. You may enter the wild card ".*" at the end of a domain name to block any web site with a host name having the domain name in the middle. For example, If you enter "foobar.*," then "www.foobar.com," "www.foobar.co.jp," or "foobar.co.uk" will be blocked. Placing the wild card in any other position is not supported. The Pepwave MAX will inspect and look for blocked domain names on all HTTP traffic. Secure web (HTTPS) traffic is not supported. 18.1.2.2 Exempted User Groups Check and select pre-defined user group(s) who can be exempted from the access blocking rules. User groups can be defined at QoS> User Groups section. Please refer to section Error! Reference source not found. for details. 18.1.2.3 Exempted Subnets With the subnet defined in the field, clients on the particular subnet(s) can be exempted from the access blocking rules.
http://www.pepwave.com 102 Copyright @ 2014 Pepwave 19 Miscellaneous Settings Themiscellaneous settings include configuration forPPTP Server,Service Forwarding, and Service Passthrough. 19.1 High Availability (Available onPepwave MAXHD2 and 700) The Pepwave MAX supports High Availability (HA) configurations via an open standard Virtual Router Redundancy Protocol (VRRP, RFC 3768). In an HA configuration, two Pepwave MAX units provide redundancy and failover in a master-slave arrangement. In the event that the Master Unit is down, the Slave Unit becomes active.High Availability will be disabled automatically where there is a Drop-in connection configured on a LAN Bypass port: In the diagram, the WAN ports of each Pepwave MAX unit connect to the router and to the modem. Both Pepwave MAX units connect to the same LAN switch via a LAN port. An elaboration on the technical details of the implementation, by Pepwave MAX, of Virtual Router Redundancy Protocol (VRRP, RFC 3768) is as follows:  In an HA configuration, the two Pepwave MAX units communicate with each other using VRRP over the LAN.  The two Pepwave MAX units broadcast heartbeat signals to the LAN at a frequency of one heartbeat signal per second.  In the event that no heartbeat signal from the Master Pepwave MAX unit is received in 3 seconds (or longer) since the last heartbeat signal, the Slave Pepwave MAXunit becomes active.  The Slave Pepwave MAX unit initiates the WAN connections, and binds to a previously configured LAN IP address.  At a subsequent point when the Master Pepwave MAX unit recovers, it will once again become active. You can configure High Availability at the following location:Network>Misc. Settings > High Availability: Interface for Master Router Interface for Slave Router
http://www.pepwave.com 103 Copyright @ 2014 Pepwave High Availability Enable Checking this box specifies that the Pepwave MAX unit is part of a High Availability configuration. Group Number This number identifies a pair of Pepwave MAX units operating in a High Availability configuration.The two Pepwave MAX units in the pair must have the same Group Number value. Preferred Role This setting specifies whether the Pepwave MAX unit operates in Master or Slave mode. Click the corresponding radio button to set the role of the unit. One of the units in the pair must be configured as the Master and the other unit must be configured as the Slave Resume Master Role Upon Recovery This option is displayed when Master mode is selected in Preferred Role. If this option is enabled, once the device has recovered from an outage, it will take over and resume its Master role from the slave unit. Configuration Sync. This option is displayed when Slave mode is selected in Preferred Role. If this option is enabled and the Master Serial Number entered matches with the actual master unit's, the master unit will automatically transfer the configuration to this unit. Please make sure the LAN IP Address and the Subnet Mask fields are set correctly in the LAN Settings page. You can refer to the Event Log for the configuration synchronization status. Master Serial Number If the box Configuration Sync. is checked, the serial number of the Master unit is required here for the feature to work properly. Virtual IP The HA pair must share the same Virtual IP. This Virtual IP and the LAN Administration IP must be under the same network. LAN Administration IP This setting specifies a LAN IP address to be used for accessing administration functionality. This address should be unique within the LAN. Subnet Mask This setting specifies the subnet mask of the LAN.
http://www.pepwave.com 104 Copyright @ 2014 Pepwave Important Note For MAXrouters in NAT mode, the Virtual IP (VIP) should be set as the default gateway for all hosts sitting on the LAN segment. For example, a firewall sitting behind the MAX router should set its default gateway as the Virtual IP instead of the IP of Master MAX unit. In Drop-in mode, no other configuration needs to be set. Please note that the Drop-in WAN cannot be configured as a LAN Bypass port while it is configured for High Availability.
http://www.pepwave.com 105 Copyright @ 2014 Pepwave 19.2 PPTP Server The Pepwave MAX has a built-in PPTP Server, which enables remote computers to conveniently and securely access the local network. PPTP server setting is located at Advanced >Misc. Settings >PPTP Server. Simply check the box to enable the PPTP server function. All connected PPTP sessions are displayed on the Client List at Status > Client List. Please refer to section 22.3 for details. PPTP Server Setting Listen On This setting is for specifying the WAN connection(s) and IP address(es) where the PPTPserver should listen on. Authentication Select the source of user databases for PPTP authentication. Local User Accounts - User accounts are stored in the device locally. You can add/modify/delete the accounts in the User Accounts table below, click Add to add a new account. LDAP Server - Authenticate with an external LDAP server. Tested with OpenLDAP server where passwords are NTLM hashed. Active Directory is not supported. (You can choose to
http://www.pepwave.com 106 Copyright @ 2014 Pepwave use RADIUS to authenticate with a Windows Server.) RADIUS Server - Authenticate with an external RADIUS server. Tested with Microsoft Windows Internet Authentication Service, and FreeRADIUS servers where passwords are NTLM hashed or in plain text. 2. User Accounts This setting allows you to define the PPTP User Accounts. Click Add to input usernameand password to create an account. After adding the user accounts, you can click on ausername to edit the account password. Click the button to delete the account in itscorresponding row. 19.3 Certificate Manager This section allows you to assign certificates for Local VPN and Web Admin SSL. The local keys will not be transferred to another device by any means.
http://www.pepwave.com 107 Copyright @ 2014 Pepwave 19.4 Service Forwarding Service Forwarding settings are located at Advanced>Misc. Settings >Service Forwarding: Service Forwarding SMTP Forwarding When this option is enabled, all outgoing SMTP connections destined for any host at TCP port 25 will be intercepted. These connections will be redirected to a specified SMTP server and port number. SMTP server settings for each WAN can be specified after selecting Enable. Web Proxy Forwarding When this option is enabled, all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings will be intercepted. These connections will be redirected to a specified web proxy server and port number. Web Proxy Interception Settings and proxy server settings for each WAN can be specified after selecting Enable. DNS Forwarding When this option is enabled, all outgoing DNS lookups will be intercepted and redirected to the built-in DNS name server. If any LAN device is using DNS name servers of a WAN connection, you may want to enable this option to enhance the DNS availability without modifying the DNS server setting of the clients. The built-in DNS name server will distribute DNS lookups to corresponding DNS servers of all available WAN connections. In this case, DNS service will not be interrupted even if any WAN connection is down. 19.4.1 SMTP Forwarding Some ISPs require their users to send e-mails via the ISP’s SMTP server. All outgoing SMTP connections are blocked except those connecting to the ISP’s.The Pepwave MAX supports intercepting and redirecting all outgoing SMTP connections (destined for TCP port 25) via a WAN connection to the WAN’s corresponding SMTP server.
http://www.pepwave.com 108 Copyright @ 2014 Pepwave To enable the feature, select the Enable check box under SMTP Forwarding Setup. Check the box Enable Forwarding?For the WAN connection(s) that needs such forwarding. Enter the ISP’s e-mail server address and TCP port number for each WAN. The Pepwave MAX will intercept SMTP connections, choose a WAN with reference to the Outbound Policy, and then forward the connection to the forwarded SMTP server if the chosen WAN has enabled forwarding. If the forwarding is disabled for a WAN connection, SMTP connections for the WAN will be simply forwarded to the connection’s original destination. Note If you want to route all SMTP connections only to particular WAN connection(s), you should create a rule in Outbound Policy (see section 13.2).
http://www.pepwave.com 109 Copyright @ 2014 Pepwave 19.4.2 Web Proxy Forwarding When this feature is enabled, the Pepwave MAX will intercept all outgoing connections destined for the proxy server specified in Web Proxy Interception Settings, choose a WAN connection with reference to the Outbound Policy, and then forward them to the specified web proxy server and port number. Redirected server settings for each WAN can be set here.If forwarding is disabled for a WAN, web proxy connections for the WAN will be simply forwarded to the connection’s original destination. 19.4.3 DNS Forwarding When DNS Forwarding is enabled, all clients’ outgoing DNS requests will also be intercepted and forwarded to the built-in DNS proxy server.
http://www.pepwave.com 110 Copyright @ 2014 Pepwave 19.5 Service Passthrough Service Passthrough settings can be found inAdvanced>Misc. Settings >Service Passthrough: Some Internet services required to be specially handled in a multi-WAN environment. The Pepwave MAX supports handling such services correctly such that Internet applications do not notice it is behind a multi-WAN router. Settings for Service Passthrough Support are available here. Service Passthrough Support SIP Session Initiation Protocol, aka SIP, is a voice-over-IP protocol. The Pepwave MAX can act as a SIP Application Layer Gateway (ALG) which binds connections for the same SIP session to the same WAN connection and translate IP address in the SIP packets correctly in NAT mode. Such passthrough support is always enabled and there are two modes for selection: Standard Mode and Compatibility Mode. If your SIP server’s signal port number is non-standard, you can check the box Define custom signal ports and input the port numbers to the text boxes. H.323 With this option enabled, protocols that provide audio-visual communication sessions will be defined on any packet network and passthrough the device. FTP FTP sessions consist of two TCP connections; one for control and one for data. In multi-WAN situation, they have to be binded to the same WAN connection. Otherwise, problems will arise in transferring files. By default, the Pepwave MAX monitors TCP control connections on port 21 for any FTP connections and binds TCP connections of the same FTP session to the same WAN. If you have an FTP server listening on a port number other than 21, you can check the box Define custom control ports and enter the port numbers to the text boxes. TFTP The Pepwave MAX monitors outgoing TFTP connections and routes any incoming TFTP data packets back to the client. Select Enable if you want to enable the TFTP Passthrough support. IPsec NAT-T This field is for enabling the support of IPsec NAT-T Passthrough. UDP ports 500, 4500 and 10000 are monitored by default. You may add more custom data ports that your IPsec system uses by checking the box Define custom ports. If the VPN contains IPsec Site-to-Site VPNtraffic, you have to check the box Route IPsec Site-to-Site VPN and choose the WAN connection to route the traffic to. If you have IPsec SpeedFusionTM traffic routed, check the Route IPsec SpeedFusionTM option and select a WAN to force routing such traffic to the specified WAN.
http://www.pepwave.com 111 Copyright @ 2014 Pepwave 20 AP The AP Controller acts as a centralized controller of Pepwave AP devices. With this feature, users will be able to customize and manage multiple AP one a single Peplink Balance Interface. To configure, navigate to the AP tab and the following options will be shown. 20.1 Wireless SSID This menu is the first one that appears upon clicking on the AP tab. This screen could also be reached by clicking on AP > Wireless SSID. AP Controller AP Management The AP Controller for managing Pepwave APs can be enabled by this option. By default, the Pepwave MAX has an integrated AP, which it will always control. By clicking the External AP, the MAX unit will also control access points connected on its LAN. When this option is enabled, the AP Controller will wait for management connections originating from APs over the LAN on TCP and UDP port 11753. It will also wait for captive portal connections on TCP port 443. An extended DHCP option "CAPWAP Access Controller addresses" (field 138) will be added to the DHCP server. A local DNS record "wlancontroller" will added to the local DNS proxy. Permitted AP With this option enabled, protocols that provide audio-visual communication sessions will be defined on any packet network and passthrough the device.
http://www.pepwave.com 112 Copyright @ 2014 Pepwave 20.2 Settings AP Settings SSID These buttons specify which wireless networks will use this AP Profile. You can also select the frequencies at which each network will transmit. Please note that the Peplink Balance does not detect weather the AP is capable of transmitting at both frequencies. Instructions to transmit at unsupported frequencies will be ignored by the AP. Operating Country This drop-down menu specifies the national / regional regulations which the AP should follow.  If a North American region is selected, RF channels 1 to 11 will be available and the maximum transmission power will be 26 dBm (400 mW).  If European region is selected, RF channels 1 to 13 will be available. The maximum transmission power will be 20 dBm (100 mW). NOTE: Users are required to choose an option suitable to local laws and regulations. The country code selection is for non-US model only and is not available to all US model. Per FCC regulation, all WiFi product marketed in US must fixed to US operation channels only. Preferred Frequency These buttons determine the frequency at which access points will attempt to broadcast. This feature will only work for AP that can transmit at both 5.4GHz and 5GHz
http://www.pepwave.com 113 Copyright @ 2014 Pepwave frequencies, Protocol (5GHz, 2.4 GHz) This section displays the wireless protocols which your AP are using. Channel Bonding (5GHz, 2.4 GHz) This drop-down menu is only available for 802.11bgn or 802.11n protocols only. There are three options: 20 MHz, 20/40 MHz and 40 MHz With this feature enabled, it allows the Wi-Fi system to use two channels at once. Using two channels improves the performance of the Wi-Fi connection Channel (5GHz, 2.4 GHz) This drop-down menu selects the 802.11 channel to be utilized. Available options are from 1 to 11 for the country setting of North America and from 1 to 13 for the country setting of Europe regionn, respectively. (Channel 14 is only available when the country is selected as Japan with protocol 802.11b.) If Auto is set, the system would perform channel scanning based on the scheduled time set and choose the most suitable channel automatically. Management VLAN ID This field specifies the VLAN ID to tag to management traffic, such as AP to AP-controller communication traffic. The value is zero by default, meaning that no VLAN tagging will be applied. NOTE: Change this value with caution as alterations may result in loss of connection to the AP controller. Power BoostA With this option enabled, the AP under this profile will transmit using additional power. Please note that using this option with several AP in close proximity will lead to increased interference. Output PowerA This drop-down menu determines the power at which the AP under this profile will broadcast. When fixed settings are selected, the AP will broadcast at the specified power level regardless of context. When Dynamic settings are selected, the AP will adjust its power level based on its surrounding AP in order to maximize performance. The Dynamic: Auto setting will set the AP to do this automatically. Otherwise, the Dynamic: Manual setting will set the AP to dynamically adjust only of instructed to do so. If you have set Dynamic:Manual, you can go to AP > Toolbox > Auto Power Adj. to give your AP further instructions. Beacon RateA This drop-down menu provides the option to send beacon in different transmit bit rate and the bit rates are: 1Mbps, 2Mbps, 5.5Mbps, 6Mbps, 11Mbps. Beacon IntervalA This drop-down menu provides the option to set the time between each beacon send. Available options are: 100ms, 250ms and 500ms. DTIMA This field provides the option to set the frequency for beacon to include Delivery Traffic Indication Message, DTIM. The interval unit is measured in milliseconds. Slot TimeA This field provides the option to modify the unit wait time before it transmits. The default value is 9μs. ACK TimeoutA This field provides the option to set the wait time to receive acknowledgement packet
http://www.pepwave.com 114 Copyright @ 2014 Pepwave before doing retransmission. The default value is 48μs. Frame AggregationA With this feature enabled, throughput will be increased by sending two or more data frames in a single transmission. A - Advanced feature, please click the button on the top right hand corner to activate. Web Administration Settings (on External AP) Enable Check the box to allow Peplink Balance to manage the web admin access information of the AP. Web Access Protocol Thesebuttonsspecify the web access protocol used for accessing the web admin of AP. The two available options are HTTP and HTTPS. Management Port This field specifies the management port used for accessing the device. HTTP to HTTPS Redirection This option will be available if you have chosen HTTPS as the Web Access Protocol. With this enabled, any HTTP access to the web admin will be redirect to HTTPS automatically. Admin User Name This field specifies the administrator username of the web admin. It is set as admin by default. Admin Password This field allows you to specify a new administrator password. You may also click the Generate button and let the system generate a random password automatically. 20.3 Toolbox Additional tools for managing firmware packs can be found under AP >Toolbox. Firmware Packs This is the first menu that will appear. Here, you can manage the firmware of your AP. Clicking on will result in information regarding each firmware pack. To receive new firmware packs, you can either press to download new packs or you can press to manually upload a firmware pack. Press to define which firmware pack is default.
http://www.pepwave.com 115 Copyright @ 2014 Pepwave 21 System Settings 21.1 Admin Security There are two user accounts available for accessing the Web Admin.Usernames are admin and user.They represent two user levels - admin has full administration access, while user is a read-only account.The read-only account can only access the device's status information and cannot make any change on the device. A web login session will be logged out automatically when it has been idle longer than the Web Session Timeout. Before the session expires, you may click the Logout button in the Web Admin to exit the session 0 hours 0 minutes signifies an unlimited session time. This setting should be used only in special situations, as it will lower the system security level if users do not logout before closing the browser. Default: 4 hours 0 minutes. For security reason, after logging in to the Web Admin Interface for the first time, it is recommended to change the administrator password. Configuring the administration interface to be accessible only from the LAN can further improve system security. Admin Account UI User Account UI
http://www.pepwave.com 116 Copyright @ 2014 Pepwave Administrative Settings configuration is located at System>Admin Security: Admin Settings Router Name This field allows you to define a name for this Pepwave MAX unit. By default, Router Name is set as MAX_XXXX, where XXXX refers to the last 4 digits of the serial number of the device. Admin User Name It is set as admin by default and is not customizable. Admin Password This field allows you to specify a new administrator password. Confirm Admin Password This field allows you to verify and confirm the new administrator password. Read-only User Name It is set as user by default and is not customizable. User Password This field allows you to specify a new user password. Once the user password is set, the feature of read-only user will be enabled. Confirm User Password This field allows you to verify and confirm the new user password. Web Session Timeout This field specifies the number of hours and minutes that a web session can remain idle before the device terminates its access to Web Admin Interface. By default, it is set as 4 hours. Authentication by RADIUS With this box is checked, Web Admin will authenticate using an external RADIUS server. Authenticated users are treated as "admin" with full read-write permission or “user” with read-only access.Local "admin" and "user" accounts will be disabled. When the
http://www.pepwave.com 117 Copyright @ 2014 Pepwave device is not able to communicate with the external RADIUS server, local accounts will be enabled again for emergency access. Authentication options will be available once this box is checked. Auth Protocol This specifies the authentication protocol used. Available options are MS-CHAP v2 and PAP. Auth Server This specifies the access address of the external RADIUS server. Auth Server Secret This is the secret for accessing the RADIUS server. Auth Timeout This option specifies the time value for authentication timeout. Accounting Server This specifies the access address of the external Accounting server. Accounting Server Secret This is the secret for accessing the Accounting server. Network Connection This option is for specifying the network connection which will be used for authentication connection. Users can choose from LAN, WAN and VPN connections. CLI SSH CLI (Command Line Interface) can be accessed via SSH. This field enables the CLI support. CLI SSH Port, CLI SSH Access These settings specify which TCP port and which interface(s) to accept remote SSH CLI access. The user name and password used for remote SSH CLI access are the same as those for web admin access. Security This option is for specifying the protocol(s) through which the Web Admin Interface can be accessible:  HTTP  HTTPS  HTTP/HTTPS Web Admin Port These fields are for specifying the port number at which the Web Admin Interface can be accessible. Web Admin Access This option is for specifying the network interfaces through which the Web Admin Interface can be accessible:  LAN only  LAN/WAN  If LAN/WAN is chosen, a WAN Connection Access Settings form will be displayed.
http://www.pepwave.com 118 Copyright @ 2014 Pepwave WAN Connection Access Settings Allowed Source IP Subnets This field allows you to restrict web admin access only from defined IP subnets.  Any - Allow web admin accesses to be from anywhere, without IP address restriction.  Allow access from the following IP subnets only - Restrict web admin access only from the defined IP subnets. When this is chosen, a text input area will be displayed beneath: The allowed IP subnet addresses should be entered into this text area. Each IP subnet must be in form of w.x.y.z/m Where w.x.y.z is an IP address (e.g. 192.168.0.0), andm is the subnet mask in CIDR format, which is between 0 and 32 inclusively. For example: 192.168.0.0/24 To define multiple subnets, separate each IP subnet one in a line. For example:  192.168.0.0/24  10.8.0.0/16 Allowed WAN IP Address(es) This is to choose which WAN IP address(es) the web server should listen on.
http://www.pepwave.com 119 Copyright @ 2014 Pepwave 21.2 Firmware Upgrade The firmware of thePepwave MAX is upgradeable through Web Admin Interface. Firmware upgrade functionality is located at System> Firmware: There are two ways to upgrade the unit. The first method is online firmware upgrade.The system can Check,Download and Upgrade over the Internet.The second method is to upload a firmware file manually. Click on the Check again button to use online upgrade. With online upgrade, Pepwave MAX checks online for new firmware.If a new firmware is available, the Pepwave MAX will automatically download the firmware. The upgrade process will subsequently be automatically initiated. You may also download a firmware image from the Pepwave web site and update the unit manually.Click Browseto select the firmware file from the local computer, and then click ManualUpgradeto send the firmware to the Pepwave MAX.The Pepwave MAX will then automatically initiate the firmware upgrade process. Please note that all Pepwave devices are equipped to be able to store two different firmware versions in two different partitions. A firmware upgrade preformed will always replace the inactive partition. If you want to keep the inactive firmware, you can simply reboot your device with the inactive firmware and then perform the firmware upgrade. Important Note The firmware upgrade process may not necessarily preserve the previous configuration, and the behavior varies on a case-by-case basis. Consult the Release Notes for the particular firmware version. Do not disconnect the power during firmware upgrade process. Do not attempt to upload a non-firmware file, or a firmware file that is not qualified, or not supported, by Pepwave. Upgrading a Pepwave MAX with an invalid firmware file will damage the unit, and may void the warranty. Important Note If the firmware is rolled back from 5.x to 4.x, the configurations will be lost.
http://www.pepwave.com 120 Copyright @ 2014 Pepwave 21.3 Time The Time Server functionality enables the system clock of thePepwave MAX to be synchronized with a specified Time Server. The settings for Time Server configuration are located at System > Time: Time Server Settings Time Zone This specifies the time zone (along with the corresponding Daylight Savings Time scheme) in which the Pepwave MAX operates. The Time Zone value affects the time stamps in the Event Log of the Pepwave MAX and E-mail notifications. Checked the box Show all to show all available time zone options. Time Server This setting specifies the NTP network time server to be utilized by the Pepwave MAX. 21.4 Email Notification The Email Notification functionality of the Pepwave MAX provides a System Administrator with up-to-date information on network status. The settings for configuring Email Notification arefound at System> Email Notification:
http://www.pepwave.com 121 Copyright @ 2014 Pepwave Email Notification Settings Email Notification This option is for enabling Email Notification. If the box Enable is checked, the Pepwave MAX sends email messages to a System Administrator when the WAN status changes, or when new firmware is available. If the box Enable is not checked, Email Notification is disabled and the Pepwave MAX will not send email messages. SMTP Server This field is for specifying the SMTP server to be used for sending email. If the server requires authentication, check the box Require authentication. SSL Encryption Check the box to enable SMTPS. When the box is checked, the next field SMTP Port will be changed to 465 automatically. SMTP Port This field is for specifying the SMTP Port number. By default, this is set to 25; when the SSL Encryption box is checked, the default port number will be set to 465. You may customize the port number by editing this field. Click the button Default to restore to default. SMTP User Name / Password This setting specifies the SMTP username and password while sending email. These options are shown only if Require authentication check box is checked in SMTP Server setting. Confirm SMTP Password This field allows you to verify and confirm the new administrator password. Sender’s Email Address This setting specifies the sender email address reported by the email messages sent by the Pepwave MAX. Recipient’s Email Address This setting specifies the email addresses to which the Pepwave MAX should send the email messages to. You may enter multiple recipients’ email addresses in this field.
http://www.pepwave.com 122 Copyright @ 2014 Pepwave After you have completed the settings, you can click the Test Email Notification button to test the settings before saving it. After it is clicked, you will see this screen to confirm the settings: Click Yes to confirm. Wait a few seconds, and you will see a return message and the detailed test result.
http://www.pepwave.com 123 Copyright @ 2014 Pepwave 21.5 EventLog The Remote Syslog functionality of thePepwave MAX enables event logging at a specified remote Syslog server. The settings for configuring Remote System Log are found atSystem>Event Log: Remote Syslog Settings Remote Syslog Remote Syslog allows syslog message to be sent to a specified remote syslog server. You can configure a remote syslog host either in the form of an IP address or a server domain name. Remote Syslog Host This setting specifies the IP address or host name of the remote Syslog server. Port This setting specifies the port number of the remote Syslog service. By default, the Port setting has value is 514.
http://www.pepwave.com 124 Copyright @ 2014 Pepwave 21.6 SNMP SNMPor Simple Network Management Protocol is an open standard that can be used to collect information from the Pepwave MAX Mobile Router. SNMP configuration is located atSystem> SNMP: SNMP Settings SNMP Device Name This field shows the router name defined in System > Admin Security. SNMP Port This option specifies the port which SNMP used. The default port is set as 161. SNMPv1 This option allows you to enable SNMP version 1. SNMPv2 This option allows you to enable SNMP version 2. SNMPv3 This option allows you to enable SNMP version 3. To add a community for either SNMPv1 or SNMPv2, click the Add SNMP Communitybutton in the Community Name table, upon which the following screen will be displayed:
http://www.pepwave.com 125 Copyright @ 2014 Pepwave SNMP Community Settings Community Name This setting specifies the SNMP Community Name. Allowed Source Subnet Address This setting specifies a subnet from which access to the SNMP server is allowed. Enter subnet address here (e.g. 192.168.1.0), and specify your subnet mask using the pull-down menu. To define a user name for SNMPv3, click Add SNMP User in the SNMPv3 User Name table, upon which the following screen is displayed: SNMPv3 User Settings User Name This setting specifies a user name to be used in SNMPv3. Authentication Protocol This setting specifies via a drop-down menu the one of the following valid authentication protocols:  NONE  MD5  SHA Specify your password on the field to the right. Privacy Protocol This setting specifies via a drop-down menu the one of the following valid privacy protocols:  NONE  DES Specify your password on the field to the right.
http://www.pepwave.com 126 Copyright @ 2014 Pepwave 21.7 InControl When this check box is checked, the device’s status information, usage data, and configuration will be sent to Pepwave’s InControl system. You can sign up for an InControl account athttps://incontrol.pepwave.com/ . You can register devices under the account, monitor device status and usage reports, and download backed up configuration files. Default: Disabled
http://www.pepwave.com 127 Copyright @ 2014 Pepwave 21.8 Configuration Backing up the Pepwave MAX settings immediately after successful completion of the initial setup is strongly recommended. The functionality to download and upload Pepwave MAX settings is found atSystem> Configuration Configuration Restore Configuration to Factory Settings The Restore Factory Settings button is to reset the configuration to the factory default settings. After clicking the button, you will need to click the Apply Changes button on the top right corner to make the settings effective. Downloading Active Configurations The purpose of the Download button is to backup the current active settings. Click Download and save the configuration file. Uploading Configurations To restore or change settings based on a configuration file, click Choose File to locate the configuration file on the local computer, and then click Upload. The new settings can then be applied by clicking the Apply Changes button on the page header, or you can cancel the procedure by pressing discard on the Main page of Web Admin Interface. Uploading Configuration from High Availability Pair (Available on Pepwave MAX HD2 and MAX 700) In a High Availability (HA) configuration, the MAX router can quickly load the configuration of its HA counterpart. To do so, click the Upload button. After loading the settings, configure the LAN IP address of the MAX router to be different from the HA counterpart.
http://www.pepwave.com 128 Copyright @ 2014 Pepwave 21.9 Feature Add-ons Some MAX routers have features that could be activated upon purchase. Once the purchase is complete, you will receive an Activation Key. Enter the key on the Activation Key field, click Activate, and then click Apply Changes. 21.10 Reboot This page provides a Reboot button for restarting the system. For highest reliability, the Pepwave MAX is equipped with two copies of firmware of different version. You can select the firmware version you would like the device to reboot with. The firmware marked with (Running) is the current system boot up firmware. Please note that a firmware upgrade will always replace the inactive firmware partition.
http://www.pepwave.com 129 Copyright @ 2014 Pepwave 21.11 Ping Test The Ping Test tool in the Pepwave MAX performs Pings through a specified Ethernet interface or a SpeedFusionTMconnection. You can specify the number of pings in the fieldNumber of timesto a maximum of 10 times, and Packet Size can be specified in the field Packet Size to a maximum of 1472 bytes. The Ping utility is located at System > Tools > Ping, illustrated as follows: Tip A system administrator can use the Ping utility to manually check the connectivity of a particular LAN/WAN connection.
http://www.pepwave.com 130 Copyright @ 2014 Pepwave 21.12 Traceroute Test The Traceroute Test tool in the Pepwave MAX traces the routing path to the destination through a particular Ethernet interface or SpeedFusionTM connection. The Traceroute Test utility is located at System > Tools > Traceroute, illustrated as follows: Tip A system administrator can use the Traceroute utility to analyze the connection path of a LAN/WAN connection. 21.13 PepVPN Test The PepVPN Test tool can help to test the throughput between different VPN peers. You can define the Test Type,Direction, and Duration of the test, and press Go!to perform the throughput test. The VPN Test utility is located at System > Tools >PepVPN Test illustrated as follows:
http://www.pepwave.com 131 Copyright @ 2014 Pepwave 21.14 PepVPN Analyzer The bandwidth bonding feature of PepVPN occurs when multiple WAN lines from one end merge with multiple WAN lines from the other end. For this to happen, each WAN line needs to form a connection with all the WAN lines on the opposite end. The function of the PepVPN Analyzer is to report the throughput, packet loss, and latency of all possible combinations of connections. This feature is located in System > PepVPN Analyzer.To utilize this feature, simply choose your profile from the drop-down menu and click Go! 21.15 CLI (Command Line Interface Support) The CLI (Command Line Interface) can be accessed via SSH. This field enables CLI support. The below settings specify which TCP port and which interface(s) should accept remote SSH CLI access. The user name and password used for remote SSH CLI access are the same as those used for web admin access.
http://www.pepwave.com 132 Copyright @ 2014 Pepwave 22 Status This section displays the information of the Pepwave MAX on the Device, ActiveSessions, Client List, WINS Client List,SpeedFusionTM,UPnP / NAT-PMP,Event Log, and Bandwidth. 22.1 Device System information is located at Status>Device: System Information Router Name This is the name specified in the field Router Name located in System > Admin Security. Model This shows the model name and number of this device. Hardware Revision This shows the hardware version of this device. Serial Number This shows the serial number of this device. Firmware This shows the firmware version that this device is currently running. Modem Support Version This shows the modem support version of this device. A Modem Support List link redirects users to a list of cellular modems supported by this device. Uptime This shows the length of time since the device is rebooted. System Time This shows the current system time. GPX File (HD2 and HD2 IP67 Only) This contains the GPS data of the latest 7 days. A Download button is for exporting the data in GPX format of the selected date. For more information about how GPS works inHD2 and HD2 IP67, please refer to section 19.1.1. Diagnostic Report A Download button is for exporting a diagnostic report file required for system investigation. The second table shows the MAC address of each LAN/WAN interface connected.
http://www.pepwave.com 133 Copyright @ 2014 Pepwave To view this you device’s End User License Agreement (EULA), please click on the icon. Important Note If you encounter issues and would like to contact PepwaveSupport Team (http://www.pepwave.com/contact/), please download the diagnostic report file and attach it along with a description of your encountered issue. In firmware 5.1 or before, Diagnostic Report file can be obtained at System > Reboot 22.1.1 GPS Data The MAX HD2and HD2 IP67automatically stores up to seven days of GPS location data in GPS eXchange format (GPX). To review this data using third-party applications, click Status>Deviceand then download your GPX file. The Pepwave MAX BR1, HD2 and HD2 IP67 export real-time location data in NMEA format through its LAN IP address at TCP port 60660. It is accessible from LAN or over a SpeedFusion connection. To access the data via a virtual serial port, you have to install a virtual serial port driver.Visit http://www.peplink.com/index.php?view=faq&id=294 to download the driver.
http://www.pepwave.com 134 Copyright @ 2014 Pepwave 22.2 Active Sessions Information on Active Sessions is at Status> Active Sessions> Overview This screen displays the number of sessions initiated by each application. Click on each Service to obtain additional information. This screen also indicates the number of sessions initiated by each WAN port. Finally, you can see which clients are initiating the most sessions.
http://www.pepwave.com 135 Copyright @ 2014 Pepwave In addition, you can also perform a filtered search for specific sessions. You can filter by subnet, port, protocol, and interface. To perform a search, navigate to: Status > Active Sessions> Search This Active Sessions section displays the active inbound / outbound and UDP / TCP sessions of each WAN connection on the Pepwave MAX. A filter is available to help sort out the active session information. Enter a keyword in the field or check one of the WAN connection boxes for filtering.
http://www.pepwave.com 136 Copyright @ 2014 Pepwave 22.3 Client List The client list table is located at Status > Client List. It lists DHCP client IP addresses, their Names (retrieved from DHCP reservation table or defined by users), current Download and Upload rate and MAC addresses that the Pepwave MAX has offered IP addresses to since it is powered up.Network Name (SSID) and Signal refers to the information about Wi-Fi AP, which is the name of the Network and its signal strength. Clients can be imported into DHCP Reservation table by clicking the button on the right-most column. Further update the record after the import by going to Network > LAN. If PPTP Server in section 19.2 is enabled, you may see the corresponding connection name would be listed in the field of Name.
http://www.pepwave.com 137 Copyright @ 2014 Pepwave 22.4 WINS Client The WINS client list table is located at Status >WINS Client. It lists WINS client IP addresses and their Names. This option will only be available when you have enabled the WINS Server in section 8.1. Name of clients retrieved will be automatically matched into Client List in the previous section. Click the button Flush All to flush all WINS client records. 22.5 SpeedFusionTM This is a page showing the current status of SpeedFusionTM, located at: Status >SpeedFusionTM Details about peer’s WAN connections are listed as below.
http://www.pepwave.com 138 Copyright @ 2014 Pepwave 22.6 UPnP / NAT-PMP The table that shows the forwarded ports under UPnP and NAT-PMP protocols is located at Status > UPnP / NAT-PMP: This section appears only if you have enabled the function of UPnP / NAT-PMP as mentioned in Section15.1.1 Click the button to delete a single UPnP / NAT-PMPrecord in its corresponding row. To delete all records, click Delete All on the right-hand side below the table. Important Note UPnP / NAT-PMP records would be deleted immediately after clicking the button or Delete Allwithout the need to click Save or Confirm.
http://www.pepwave.com 139 Copyright @ 2014 Pepwave 22.7 Event Log Event Log information is located at Status>Event Log: The log section displays a list of events that has taken place on the Pepwave MAX unit.Click the Auto Refresh to retrieve log entries again. Click the Clear Log button to clear the log.
http://www.pepwave.com 140 Copyright @ 2014 Pepwave 22.8 Bandwidth This section shows the bandwidth usage statistics, located at:Status > Bandwidth Bandwidth usage at the LAN and when the device is switched off, bandwidth usage is not recorded and not shown. 22.8.1 Real-Time The Data transferred since installation shows you how many network traffic has been processed by your device since first boot. Click Show Details in the top right hand corner of each table and the details of data transferred will be shown. The check box Stacked below the data transferred graph can be checked to show the aggregated transferred rate of both traffic directions.
http://www.pepwave.com 141 Copyright @ 2014 Pepwave 22.8.2 Hourly This page shows the daily bandwidth usage for all and each WAN connection. Select the connection in which you want to check its usage from the drop down menu 22.8.3 Daily This page shows the daily bandwidth usage for all and each WAN connection. Select the connection in which you want to check its usage from the drop down menu. If you have enabled Bandwidth Monitoring feature as shown in section9.5, the Current Billing Cycle table for that WAN connection will be displayed. Click on a date to view the client bandwidth usage of that specific date. This feature is not available if you have selected to view the bandwidth usage of only a particular WAN connection. The Scale of the graph can be set to show in Megabyte (MB) or Gigabyte (GB).
http://www.pepwave.com 142 Copyright @ 2014 Pepwave All WAN Daily Bandwidth Usage 22.8.4 Monthly This page shows the monthly bandwidth usage for each WAN connection. If you have enabled Bandwidth Monitoring feature as shown in section9.5, you can choose a particular connection to check its usage and select to show the monthly usage period in Billing Cycle or Calendar Month. Click the first or second row to view the client bandwidth usage of the current month.This feature is not available if you have chosen to view the bandwidth usage of only a particular WAN connection. The Scale of the graph can be set to show in Megabyte (MB) or Gigabyte (GB).
http://www.pepwave.com 143 Copyright @ 2014 Pepwave All WAN Monthly Bandwidth Usage
http://www.pepwave.com 144 Copyright @ 2014 Pepwave Ethernet WAN Monthly Bandwidth Usage Tip By default, the scale of data size is in MB. 1GB equals to 1024MB.
http://www.pepwave.com 145 Copyright @ 2014 Pepwave Appendix A. Restoration of Factory Defaults To restore the factory default settings on a Pepwave MAX unit, follow the steps below: 1. Locate the reset button on the front panel ofPepwave MAX unit. 2. With a paper clip, press the reset button and hold it for at least 10 seconds until the unit reboots itself. Afterthe Pepwave MAX finishes rebooting, the factory default settings will be restored. Important Note All previous configurations and bandwidth usage data will be lost after restoring the factory default settings. Regular backup of configuration settings is strongly recommended.
http://www.pepwave.com 146 Copyright @ 2014 Pepwave Appendix B. Declaration 1. The device supports time division technology 2. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Operations in the 5.15-5.25GHz band are restricted to indoor usage only. IMPORTANT NOTE FCC Radiation Exposure Statement (for MAX700/ HD2/ HD2 IP67/ BR1) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. FCC Radiation Exposure Statement (for MAX On-The-Go) This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. 1. 20cm minimum when the product is operated alone without co-transmitting with a plug-in 3G USB dongle device. 2. 65cm minimum when the product is operated with a plug-in 3G USB device which has maximum of 7W ERP output power. 3. For co-transmission scenario which is not covered above, please consult the RF technician or device supplier. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
http://www.pepwave.com 147 Copyright @ 2014 Pepwave The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. 3. CE Statement for MAX BR1 Europe – EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC: - EN 60950-1: 2006 + A11 : 2009+A1 : 2010+ A12: 2011 Safety of Information Technology Equipment - EN50385 : 2002 / Article 3(1)(a) Product standard to demonstrate the compliance of radio base stations and fixed terminal stations for wireless telecommunication systems with the basic restrictions or the reference levels related to human exposure to radio frequency electromagnetic fields (110MHz - 40 GHz) - General public EN 300 328 V1.7.1: 2006 Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating in the 2,4 GHz ISM band and using spread spectrum modulation techniques; Harmonized EN covering essential requirements under article 3.2 of the R&TTE Directive - EN 301 908-1 V5.2.1: 2011 Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements, covering essential requirements of article 3.2 of the R&TTE Directive - EN 301 511 V9.0.2: 2003 Global System for Mobile communications (GSM); Harmonized standard for mobile stations in the GSM 900 and DCS 1800 bands covering essential requirements under article 3.2 of the R&TTE directive (1999/5/EC) - EN 301 489-1 V1.9.2: 2008 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements - EN 301 489-7 V1.3.1: 2005 ElectroMagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment ad services; Part 7: Specific conditions for mobile and portable radio and ancillary equipment of digital cellular radio telecommunications systems (GSM and DCS) - EN 301 489-17 V2.2.1: 2012 Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment - EN 301 489-24 V1.5.1: 2010 Electromagnetic compatibility and Radio Spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 24: Specific conditions for IMT-2000 CDMA Direct Spread (UTRA) for Mobile and portable (UE) radio and ancillary equipment
http://www.pepwave.com 148 Copyright @ 2014 Pepwave 0081 Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish] Undertegnede [fabrikantens navn] erklæ rer herved, at følgende udstyr [udstyrets typebetegnelse] overholder de væ sentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German] Hiermit erklärt [Name des Herstellers], dass sich das Gerät [Gerätetyp] in Ü bereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti [Estonian] Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust direktiivi 1999/5/EÜ põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish] Por medio de la presente [nombre del fabricante] declara que el [clase de equipo] cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΣΗΝ ΠΑΡΟΤ΢Α [name of manufacturer] ΔΗΛΩΝΕΙ ΟΣΙ [type of equipment] ΢ΤΜΜΟΡΦΩΝΕΣΑΙ ΠΡΟ΢ ΣΙ΢ ΟΤ΢ΙΩΔΕΙ΢ ΑΠΑΙΣΗ΢ΕΙ΢ ΚΑΙ ΣΙ΢ ΛΟΙΠΕ΢ ΢ΥΕΣΙΚΕ΢ ΔΙΑΣΑΞΕΙ΢ ΣΗ΢ ΟΔΗΓΙΑ΢ 1999/5/ΕΚ. Français [French] Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian] Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian] Ar šo [name of manufacturer / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian] Šiuo [manufacturer name] deklaruoja, kad šis [equipment type] atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch] Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese] Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar [Hungarian] Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus]megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish] Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian] [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak] [Meno výrobcu] týmto vyhlasuje, že [typ zariadenia]spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish] [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen. Svenska [Swedish] Härmed intygar [företag] att denna [utrustningstyp] står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Contact Us: Sales http://www.pepwave.com/contact/sales/ Support http://www.pepwave.com/contact/ Business Development and Partnerships http://www.pepwave.com/partners/channel-partner-program/ Address: United States Office 800 West El Camino Real, Mountain View CA 94040 United States Tel: +1 (650) 450 9669 Fax: +1 (866) 625 4664 Hong Kong Office A5, 5/F, HK Spinners Industrial Building, Phase 6, 481 Castle Peak Road, Cheung Sha Wan, Hong Kong Tel: +852 2990 7600 Fax: +852 3007 0588 What are we doing at the moment? Follow us on Twitter! http://twitter.com/Peplink Want to know more about us? Add us on Facebook! http://www.facebook.com/peplink Difficulties when configuring the device? Visit Our YouTube Channel! http://www.youtube.com/PeplinkChannel

Navigation menu