Pioneer K047 CD RDS RECEIVER User Manual

Pioneer Corporation CD RDS RECEIVER

UserManual.wiki >

K047 User Manual

User Manual

Operation ManualCD RDS RECEIVERDEH-80PRSEnglish

Thank you for purchasing this PIONEER product.To ensure proper use, please read through this manual before using this product. Itis especially important that you read and observe WARNINGs and CAUTIONsinthis manual. Please keep the manual in a safe and accessible place for future refer-ence.Before you startInformation to User 3The Safety of Your Ears is in Your Hands 3About this unit 4After-sales service for Pioneer products 4In case of trouble 5Visit our website 5Resetting the microprocessor 5Switching the DSP setting mode 5Switching between RCA input modes 6Demo mode 6About this manual 6Operating this unitHead unit 7Remote control 7Set up menu 8Basic operations 8Use and care of the remote control 9Menu operations identical for functionsettings/audio adjustments/initial settings/lists 10Tuner 10CD/CD-R/CD-RW and external storagedevices (USB, SD) 12iPod 15Using Pandoraâ17Audio adjustments 19Using Bluetooth wireless technology 32Initial settings 36Other functions 37Additional informationTroubleshooting 41Error messages 42Handling guidelines 44Compressed audio compatibility (disc, USB,SD) 46iPod compatibility 47Sequence of audio files 47Bluetooth profiles 48Copyright and trademark 48Specifications 50ContentsEn2

FCC ID: AJDK047MODEL NO.: DEH-80PRSIC: 775E-K047This device complies with Part 15 of FCC Rulesand Industry Canada licence-exempt RSS stan-dard(s). Operation is subject to the followingtwo conditions: (1) this device may not causeinterference, and (2) this device must acceptany interference, including interference thatmay cause undesired operation of this device.This transmitter must not be co-located or op-erated in conjunction with any other antennaor transmitter.The antenna for Bluetooth cannot be removed(or replaced) by user.This equipment complies with FCC/IC radiationexposure limits set forth for an uncontrolledenvironment and meets the FCC radio fre-quency (RF) Exposure Guidelines in Supple-ment C to OET65 and RSS-102 of the IC radiofrequency (RF) Exposure rules. This equipmenthas very low levels of RF energy that it deemedto comply without maximum permissive expo-sure evaluation (MPE). But it is desirable thatit should be installed and operated keeping theradiator at least 20 cm or more away from per-son’s body (excluding extremities: hands,wrists, feet and ankles).Information to UserAlteration or modifications carried out withoutappropriate authorization may invalidate theuser’s right to operate the equipment.NoteThis equipment has been tested and found tocomply with the limits for a Class B digital de-vice, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reason-able protection against harmful interference ina residential installation. This equipment gen-erates, uses and can radiate radio frequencyenergy and, if not installed and used in accor-dance with the instructions, may cause harm-ful interference to radio communications.However, there is no guarantee that interfer-ence will not occur in a particular installation.If this equipment does cause harmful interfer-ence to radio or television reception, whichcan be determined by turning the equipmentoff and on, the user is encouraged to try to cor-rect the interference by one or more of the fol-lowing measures:- Reorient or relocate the receiving antenna.- Increase the separation between the equip-ment and receiver.- Connect the equipment into an outlet on acircuit different from that to which the receiveris connected.- Consult the dealer or an experienced radio/TVtechnician for help.The Safety of Your Ears is inYour HandsGet the most out of your equipment by playingit at a safe level—a level that lets the soundcome through clearly without annoying blar-ing or distortion and, most importantly, with-out affecting your sensitive hearing. Soundcan be deceiving. Over time, your hearing“comfort level”adapts to higher volumes ofsound, so what sounds “normal”can actuallybe loud and harmful to your hearing. Guardagainst this by setting your equipment at asafe level BEFORE your hearing adapts.En 3Section01Before you startBefore you start

ESTABLISH A SAFE LEVEL:!Set your volume control at a low setting.!Slowly increase the sound until you canhear it comfortably and clearly, without dis-tortion.!Once you have established a comfortablesound level, set the dial and leave it there.BE SURE TO OBSERVE THE FOLLOWINGGUIDELINES:!Do not turn up the volume so high that youcan’t hear what’s around you.!Use caution or temporarily discontinue usein potentially hazardous situations.!Do not use headphones while operating amotorized vehicle; the use of headphonesmay create a traffic hazard and is illegal inmany areas.About this unitThe tuner frequencies on this unit are allo-cated for use in North America. Use in otherareas may result in poor reception.WARNINGHandling the cord on this product or cords asso-ciated with accessories sold with the productmay expose you to chemicals listed on proposi-tion 65 known to the State of California and othergovernmental entities to cause cancer and birthdefect or other reproductive harm. Wash handsafter handling.CAUTION:USE OF CONTROL OR ADJUSTMENT ORPERFORMANCE OF PROCEDURESOTHER THAN THOSE SPECIFIED HEREINMAY RESULT IN HAZARDOUS RADIATIONEXPOSURE.CAUTION:THE USE OF OPTICAL INSTRUMENTSWITH THIS PRODUCT WILL INCREASEEYE HAZARD.CAUTION!Do not allow this unit to come into contactwith liquids. Electrical shock could result.Also, damage to this unit, smoke, and over-heating could result from contact with liquids.!Always keep the volume low enough to hearoutside sounds.!Avoid exposure to moisture.!If the battery is disconnected or discharged,any preset memory will be erased.Important (Serial number)The serial number is located on the bottom ofthis unit. For your own security and convenience,be sure to record this number on the enclosedwarranty card.NoteFunction setting operations are completed even ifthe menu is cancelled before the operations areconfirmed.After-sales service forPioneer productsPlease contact the dealer or distributor fromwhere you purchased this unit for after-salesservice (including warranty conditions) or anyother information. In case the necessary infor-mation is not available, please contact thecompanies listed below:Please do not ship your unit to the companiesat the addresses listed below for repair withoutadvance contact.En4Section01 Before you start

U.S.A.Pioneer Electronics (USA) Inc.CUSTOMER SUPPORT DIVISIONP.O. Box 1760Long Beach, CA 90801-1760800-421-1404CANADAPioneer Electronics of Canada, Inc.CUSTOMER SATISFACTION DEPARTMENT340 Ferrier StreetUnit 2Markham, Ontario L3R 2Z5, Canada1-877-283-5901905-479-4411For warranty information please see the Lim-ited Warranty sheet included with this unit.In case of troubleShould this unit fail to operate properly, pleasecontact your dealer or nearest authorizedPIONEER Service Station.Visit our websitehttp://www.pioneerelectronics.comin Canadahttp://www.pioneerelectronics.ca!Learn about product updates (such as firm-ware updates) for your product.!Register your product to receive noticesabout product updates and to safeguardpurchase details in our files in the event ofloss or theft.!Access owner’s manuals, spare parts infor-mation, service information, and muchmore.Resetting the microprocessorThe microprocessor must be reset in the fol-lowing situations:!Before using this unit for the first time afterinstallation!If the unit fails to operate properly!When strange or incorrect messages ap-pear on the display1 Remove the front panel.For details, refer to Removing the front panel toprotect your unit from theft on page 9.2 Press RESET with a pen tip or otherpointed instrument.RESET buttonSwitching the DSP settingmodeThis unit features two operation modes: the 3-way network mode (NW) and the standardmode (STD). You can switch between modesas desired. Initially, the DSP setting is set tothe standard mode (STD).!After switching, reset the microprocessor.WARNINGDo not use the unit in standard mode when aspeaker system for 3-way network mode is con-nected to this unit. This may cause damage tothe speakers.En 5Section01Before you startBefore you start

1 Use a thin, flathead screwdriver tochange the DSP switch on the bottom ofthis unit.2 Press RESET with a pen tip or otherpointed instrument.NoteThis unit's audio settings will continue to remainin the memory even if the battery is disconnectedor the microprocessor reset. If you want to resetthe audio settings, refer to AUDIO reset (audioreset) on page 36.Switching between RCAinput modesIf you connect the unit to an audio device withRCA output, or to one with no RCA output,you can set it up so that the audio from theaudio device is output through speakers con-nected to the unit. Change settings as neces-sary based on whether the connected devicehas RCA output or not.!For more details on how to connect theunit, refer to the installation manual.%Use a thin, flathead screwdriver tochange the RCA input mode switch on thebottom of this unit.!L(Low) - If inputting from the RCA output ofa connected device!H(High) - If inputting from the speaker out-put of a connected deviceDemo modeImportant!Failure to connect the red lead (ACC) of thisunit to a terminal coupled with ignition switchon/off operations may lead to battery drain.!Remember that if the feature demo continuesoperating when the car engine is turned off, itmay drain battery power.The demo starts automatically if you do not op-erate this unit within about 30 seconds since itwas last operated or if the ignition switch isset to ACC or ON while it is turned off. To can-cel the demo mode, press and hold ( /DISP).Press and hold ( /DISP) again to start. Youcan also deactivate demo mode in the initialsettings. Select Demonstration (demo displaysetting) and turn off the demo display. For de-tails, refer to Initial settings on page 36.About this manual!In the following instructions, USB mem-ories, USB portable audio players, and SDmemory cards are collectively referred to as“external storage devices (USB, SD)”.Ifonly USB memories and USB portableaudio players are indicated, they are collec-tively referred to as “USB storage devices”.!In this manual, iPod and iPhone will be re-ferred to as “iPod”.En6Section01 Before you start

Head unit1934 568b a27cdefPart Part1(phone/onhook) 9BAND/(iPod)2LEVER aSRC/OFF3/DISP bMULTI-CONTROL(M.C.)4(list) cDisc loading slot5Open button dh(eject)6AUX input jack(3.5 mm stereojack)Auto TA and EQ mi-crophone inputjackUse to connect anauto TA and EQ mi-crophone.eSD memory cardslotRemove the frontpanel to access theSD memory cardslot.7/fRESET8EQ/DISP OFFCAUTIONUse a Pioneer USB cable when connecting theUSB audio player/USB memory device as devicesconnected to the unit directly will protrude out,which is dangerous.Do not use unauthorized products.Remote controlRemote controller buttons marked with thesame numbers as on the unit operate in thesame way as the corresponding unit button re-gardless of button name.gmka9h3jliPart OperationgVOLUME Press to increase or decrease vo-lume.hMUTE Press to mute. Press again to un-mute.ia/b/c/dPress to perform manual seektuning, fast forward, reverse andtrack search controls.Also used for controlling func-tions.jWhile operating the phone, pressto end a call or reject an incomingcall.kePress to pause or resume play-back.lPress to start talking on thephone while operating a phone.mLIST/ENTERPress to display the disc title,track title, folder, or file list de-pending on the source.While in the operating menu,press to control functions.En 7Section02Operating this unitOperating this unit

Set up menuWhen you turn the ignition switch to ON afterinstallation, set up menu appears on the dis-play.You can set up the menu options below.1 After installation of this unit, turn theignition switch to ON.SET UP appears.2 Turn M.C. to switch to YES.#If you do not operate for 30 seconds, the setup menu will not be displayed.#If you prefer not to set up at this time, turnM.C. to switch to NO.If you select NO, you cannot set up in the set upmenu.3 Press M.C. to select.4 Perform the following procedures toset the menu.To proceed to the next menu option, you needto confirm your selection.Language select (multi-language)1Turn M.C. to select the desired language.English—Français—Español2Press M.C. to confirm the selection.Calendar (setting the date)1Turn M.C. to change the year.2Press M.C. to select day.3Turn M.C. to change the day.4Press M.C. to select month.5Turn M.C. to change the month.6Press M.C. to confirm the selection.Clock (setting the clock)1Turn M.C. to adjust hour.2Press M.C. to select minute.3Turn M.C. to adjust minute.4Press M.C. to confirm the selection.Contrast (display contrast setting)1Turn M.C. to adjust the contrast level.0to 15 is displayed as the level is increased or de-creased.2Press M.C. to confirm the selection.Demonstration (demo display setting)1Turn M.C. to set the demo display to off.2Press M.C. to confirm the selection.Quit appears.5 To finish your settings, turn M.C. to se-lect YES.#If you prefer to change your setting again, turnM.C. to switch to NO.6 Press M.C. to select.Notes!Because demonstration mode is the functionfor displaying at stores, do not use this func-tion while driving.!You can set up the menu options in the initialsettings. For details about the settings, refer toInitial settings on page 36.!You can cancel set up menu by pressing SRC/OFF.Basic operationsImportant!Handle gently when removing or attachingthe front panel.!Avoid subjecting the front panel to excessiveshock.!Keep the front panel out of direct sunlight andhigh temperatures.!To avoid damaging the device or vehicle inter-ior, remove any cables and devices attachedto the front panel before detaching it.En8Section02 Operating this unit

Removing the front panel to protect your unit fromtheftThe front panel can be detached to deter theft.1Press the open button to open the front panel.2Grip the left side of the front panel and pull itgently outward.Take care not to grip it too tightly or to drop thefront panel and protect it from contact with wateror other fluids to prevent permanent damage.3Always keep the detached front panel in a protec-tion device such as a protection case.Re-attaching the front panel1Reattach the front panel by holding it upright tothe unit and clipping it securely into the mount-ing hooks.Turning the unit on1Press SRC/OFF to turn the unit on.Turning the unit off1Press and hold SRC/OFF until the unit turns off.Selecting a source1Press SRC/OFF to cycle between:TUNER (tuner)—CD (CD player)—USB1 (USB1)/iPod1 (iPod1)—Pandora1 (Pandora1)—USB2(USB2)/iPod2 (iPod2)—Pandora2 (Pandora2)—SD (SD memory card)—AUX1 (AUX1)—AUX2(AUX2)—BT Audio (BT audio)Adjusting the volume1Turn M.C. to adjust the volume.CAUTIONFor safety reasons, park your vehicle when remov-ing the front panel.Notes!When this unit’s blue/white lead is connectedto the vehicle’s auto-antenna relay controlterminal, the vehicle’s antenna extends whenthis unit’s source is turned on. To retract theantenna, turn the source off.!When there are two USB storage devices con-nected to this unit and you want to switch be-tween them for playback, disconnectcommunications for the USB storage devicefirst before proceeding.!If connecting both USB1 (USB storage de-vice1)/iPod1 (iPod connected using USBinput1) and USB2 (USB storage device2)/iPod2 (iPod connected using USB input2) atthe same time, use a Pioneer USB cable (CD-U50E) in addition to the regular Pioneer USBcable.!Set the Pandora application to off when youselect iPod source. The source may beswitched to Pandora automatically if the appli-cation is on.Use and care of the remotecontrolUsing the remote control1Point the remote control in the direction of thefront panel to operate.When using for the first time, pull out the filmprotruding from the tray.Replacing the battery1Slide the tray out on the back of the remote con-trol.2Insert the battery with the plus (+) and minus (–)poles aligned properly.WARNING!Keep the battery out of the reach of children.Should the battery be swallowed, consult adoctor immediately.!Batteries (battery pack or batteries installed)must not be exposed to excessive heat suchas sunshine, fire or the like.CAUTION!Use one CR2025 (3 V) lithium battery.En 9Section02Operating this unitOperating this unit

!Remove the battery if the remote control is notused for a month or longer.!There is a danger of explosion if the battery isincorrectly replaced. Replace only with thesame or equivalent type.!Do not handle the battery with metallic tools.!Do not store the battery with metallic objects.!If the battery leaks, wipe the remote controlcompletely clean and install a new battery.!When disposing of used batteries, complywith governmental regulations or environmen-tal public institutions’rules that apply in yourcountry/area.!“Perchlorate Material –special handling mayapply.See www.dtsc.ca.gov/hazardouswaste/perchlorate. (Applicable to California, U.S.A.)”Important!Do not store the remote control in high tem-peratures or direct sunlight.!The remote control may not function properlyin direct sunlight.!Do not let the remote control fall onto thefloor, where it may become jammed under thebrake or accelerator pedal.Menu operations identicalfor function settings/audioadjustments/initialsettings/listsReturning to the previous displayReturning to the previous list/category (the folder/ca-tegory one level higher)1Press /DISP.Turning the demo display on or off1Press and hold /DISP.Returning to the ordinary displayCanceling the initial setting menu1Press BAND/.Returning to the ordinary display from the list/cate-gory1Press BAND/.Selecting a function or list1Turn M.C. or LEVER.!In this manual, “Turn M.C.”is used to describethe operation used to select a function or list.TunerBasic operations9 b83 4 61 2 75RDSab1 4 632 75Non-RDS or AM1TAG indicator2Tags transferring indicator3Band indicator45(stereo) indicator5LOC indicatorAppears when local seek tuning is on.6Preset number indicator7Signal level indicator8TEXT indicatorShows when the radio text is received.9Program service nameaFrequency indicatorbVoltage indicatorShows the battery voltage.En10Section02 Operating this unit

!The level displayed on the voltage indi-cator may differ from the actual voltagelevel.Selecting a band1Press BAND/until the desired band (FM-1,FM-2,FM-3 for FM or AM) is displayed.Manual tuning (step by step)1Turn LEVER.Seeking1Turn and hold down LEVER.!While turning and holding down LEVER,youcan skip stations. Seek tuning starts as soonas you release LEVER.Storing and recalling stationsfor each band1 Press (list).The preset screen is displayed.2 Use M.C. to store the selected fre-quency in the memory.Turn to change the preset number. Press andhold to store.3 Use M.C. to select the desired station.Turn to change the station. Press to select.#All stations stored for FM bands can be re-called from each independent FM band.#You can tune the channel up or down manu-ally by pressing or .#Press BAND/or (list) to return to the or-dinary display.Switching the displayDesired information can be displayed whiletag information has been broadcasting.Selecting the desired text information1Press /DISP.Frequency or program service name—song titleand artist nameUsing iTunes taggingThis function can be operated with the followingiPod models.—iPod touch 4th generation—iPod touch 3rd generation—iPod touch 2nd generation—iPod touch 1st generation—iPod classic 160GB—iPod classic 120GB—iPod classic—iPod nano 6th generation—iPod nano 5th generation—iPod nano 4th generation—iPod nano 3rd generation—iPhone 4—iPhone 3GS—iPhone 3G—iPhoneHowever, tag information can be stored in thisunit even while other iPod models are used.The song information (tag) can be saved fromthe broadcasting station to your iPod. Thesongs will show up in a playlist called “Taggedplaylist”in iTunes the next time you sync youriPod. Then you can directly buy the songs youwant from the iTunes Store.!The tagged songs and the song that youcan buy from the iTunes Store may be dif-ferent. Make sure to confirm the song be-fore you make the purchase.Storing the tag information to this unit1Tune in to the broadcast station.2Press and hold M.C. if TAG is indicated in the dis-play while desired song is broadcasting.!While storing the tag data on this unit, TAGflashes.Storing the tagged information to your iPod1Connect an iPod to the USB cable using an iPodDock Connector.2Select Tags transfer from the function settings totransfer tag information from this unit to the iPod.Refer to Tags transfer (Tags transfer) on page 17.!If you switch sources during tag transfer, thetransfer will stop. To cancel the transfer, selectTags transfer from the function settings andthen try transferring the tag information again.En 11Section02Operating this unitOperating this unit

Using radio textDisplaying radio textYou can display the currently received radio text andthe three most recent radio texts.1Press and hold down (list) to display radio text.!You can turn off radio text display by pressing/DISP,SRC/OFF or BAND/ .!When no radio text is received, NO TEXT ap-pears in the display.2Turn LEVER left or right to recall the three mostrecent radio texts.3Press or to scroll.Storing and recalling radio textYou can store data from up to six radio text transmis-sions to the RT Memo 1 to RT Memo 6 keys.1Display the radio text you want to store in thememory.2Press (list).The preset screen is displayed.3Use LEVER to store the selected radio text.Turn it to change the preset number. Press andhold down M.C. to store.4Use LEVER to select the desired radio text.Turn it to change the radio text. Press M.C. to se-lect.!To return to the ordinary display, press BAND/or (list).!The tuner automatically stores the three lat-est radio text broadcasts received, repla-cing the oldest text with the newest text.Function settings1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select FUNCTION.3 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.!If AM band is selected, only BSM,Localand Tuning Mode are available.BSM (best stations memory)BSM (best stations memory) automatically stores thesix strongest stations in the order of their signalstrength.1Press M.C. to turn BSM on.To cancel, press M.C. again.Local (local seek tuning)Local seek tuning lets you tune in to only those radiostations with sufficiently strong signals for good re-ception.1Press M.C. to turn local on.!To cancel, press M.C. again.2Turn LEVER left or right to select the desired set-ting.FM: Level 1—Level 2—Level 3—Level 4AM: Level 1—Level 2The highest level setting allows reception of onlythe strongest stations, while lower levels allow thereception of weaker stations.Tuning Mode (LEVER tuning setting)You can assign a function to the LEVER on the unit.Select Manual (manual tuning) to tune up or downmanually or select Preset (preset channel) to switchbetween preset channels.1Press M.C. to select Manual or Preset.CD/CD-R/CD-RW and externalstorage devices (USB, SD)Basic operations75 6 843211Bit rate/sampling frequency indicatorShows the bit rate or sampling frequency ofthe current track (file) when the compressedaudio is playing.!When playing back VBR (variable bitrate)-recorded AAC files, the average bitrate value is displayed. However, de-pending on the software used to decodeAAC files, VBR may be displayed.2Folder number indicatorShows the folder number currently playingwhen the compressed audio is playing.3Track number indicatorEn12Section02 Operating this unit

4PLAY/PAUSE indicator5S.Rtrv indicatorAppears when Sound Retriever function is on.6Song time (progress bar)7Play time indicator8Voltage indicatorShows the battery voltage.!The level displayed on the voltage indi-cator may differ from the actual voltagelevel.Opening the front panel1Press the open button.Disc loading slot appears.Playing a CD/CD-R/CD-RW1Insert the disc into the disc loading slot with thelabel side up.Ejecting a CD/CD-R/CD-RW1Press h(eject).Playing songs on a USB storage device1Use a Pioneer USB cable to connect the USB sto-rage device to the unit.!Plug in the USB storage device using the USBcable.Stopping playback of files on a USB storage device!You may disconnect the USB storage device atany time.Playing songs on an SD memory card1Remove the front panel.For details, refer to Removing the front panel toprotect your unit from theft on page 9.2Insert an SD memory card into the SD card slot.Insert it with the contact surface facing down,and press on the card until it clicks and comple-tely locks into place.3Re-attach the front panel.4Press SRC/OFF to select SD as the source.Playback will start.Stopping playback of files on an SD memory card1Remove the front panel.For details, refer to Removing the front panel toprotect your unit from theft on page 9.2Press on the SD memory card until it clicks.The SD memory card is ejected.3Pull out the SD memory card.4Re-attach the front panel.Selecting a folder1Press or .Selecting a track1Turn LEVER.Fast forwarding or reversing1Turn and hold down LEVER to the right or left.Returning to root folder1Press and hold BAND/.Switching between compressed audio and CD-DA1Press BAND/.Switching between playback memory devicesYou can switch between playback memory devices onUSB storage devices with more than one Mass Sto-rage Device-compatible memory device.1Press BAND/.!You can switch between up to 32 different mem-ory devices.Notes!When playing compressed audio, there is nosound during fast forward or reverse.!Disconnect USB storage devices from the unitwhen not in use.!If there are two USB storage devices con-nected to this unit, the device connected tothe input of the selected source is the onethat is operated.!Disconnect communications for the USB sto-rage device before switching to operation ofthe other device.Displaying text informationSelecting the desired text information1Press /DISP.Notes!Depending on the version of iTunes used towrite MP3 files to a disc or media file types, in-compatible text stored within an audio filemay be displayed incorrectly.!Text information items that can be changeddepend on the media.En 13Section02Operating this unitOperating this unit

Selecting and playing files/tracks from the name listIf there are external storage devices (USB, SD)connected to the unit, this function is onlyavailable when Music browse is set to OFF.Refer to Music browse (music browse) onpage 36.1 Press (list) to switch to the file/trackname list mode.2 Use M.C. to select the desired file name(or folder name).Changing the file or folder name1Turn M.C.You can also perform this operation by turningLEVER.Playing1When a file or track is selected, press M.C.Viewing a list of the files (or folders) in the selectedfolder1When a folder is selected, press M.C.Playing a song in the selected folder1When a folder is selected, press and hold M.C.Browsing for a song!This function is only available when a fileon an external storage device (USB, SD) ora song on an iPod is being played.!If there are external storage devices (USB,SD) connected to the unit, this function isonly available when Music browse is set toUSB memory1,USB memory2 or SD card.Refer to Music browse (music browse) onpage 36.1 Press (list) to switch to the top menuof the list search.2 Use M.C. to select a category/song.Changing the name of the song or category1Turn M.C.Artists (artists)—Albums (albums)—Songs(songs)—Genres (genres)You can also perform this operation by turningLEVER.Playing1When a song is selected, press M.C.Viewing a list of songs in the selected category1When a category is selected, press M.C.Playing a song in the selected category1When a category is selected, press and hold M.C.Searching the list by alphabet1When a list for the selected category is displayed,press to switch to alphabet search mode.2Turn M.C. to select a letter.3Press M.C. to display the alphabetical list.Notes!This unit must create an index in order to facil-itate Artists,Albums,Songs, and Genressearches. Typically, it will take approximately70 seconds to create an index for 1 000 songs,and we recommend that up to 3 000 songs beused. Please note that certain types of filemay take longer to index than others.!Depending on the number of files in the USBstorage device, there may be a delay when dis-playing a list.!Keys may not have any effect during the crea-tion of an index or list.!Lists are recreated each time the unit isturned on.Function settings1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select FUNCTION.3 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.En14Section02 Operating this unit

Play mode (repeat play)1Press M.C. to select a repeat play range.CD/CD-R/CD-RW!Disc repeat –Repeat all tracks!Track repeat –Repeat the current track!Folder repeat –Repeat the current folderExternal storage device (USB, SD)!All repeat –Repeat all files!Track repeat –Repeat the current file!Folder repeat –Repeat the current folderRandom mode (random play)1Press M.C. to turn random play on or off.Link play (link play)1Press M.C. to display the setting mode.2Turn M.C. to change the mode; press to select.!Artist –Plays an album of the artist currentlybeing played.!Album –Plays a song from the album currentlybeing played.!Genre –Plays an album from the genre currentlybeing played.The selected song/album will be played after the cur-rently playing song.!This function is only available for external storagedevices (USB, SD).Pause (pause)1Press M.C. to pause or resume.Sound Retriever (sound retriever)Automatically enhances compressed audio and re-stores rich sound.1Press M.C. to select the desired setting.OFF (off)—1—21is effective for low compression rates, and 2iseffective for high compression rates.iPodBasic operations75 6 843211Repeat indicator2Song number indicator3Shuffle indicator4PLAY/PAUSE indicator5S.Rtrv indicatorAppears when Sound Retriever function is on.6Song time (progress bar)7Play time indicator8Voltage indicatorShows the battery voltage.!The level displayed on the voltage indi-cator may differ from the actual voltagelevel.Playing songs on an iPod1Connect an iPod to the USB cable using an iPodDock Connector.Selecting a track (chapter)1Turn LEVER.Fast forwarding or reversing1Turn and hold down LEVER to the right or left.Selecting an album1Press or .Notes!The iPod cannot be turned on or off when thecontrol mode is set to AUDIO.!Disconnect headphones from the iPod beforeconnecting it to this unit.!The iPod will turn off about two minutes afterthe ignition switch is set to OFF.Displaying text informationSelecting the desired text information1Press /DISP.En 15Section02Operating this unitOperating this unit

Browsing for a song1 Press (list) to switch to the top menuof the list search.2 Use M.C. to select a category/song.Changing the name of the song or category1Turn M.C.Playlists (playlists)—Artists (artists)—Albums(albums)—Songs (songs)—Podcasts (podcasts)—Genres (genres)—Composers (composers)—Audiobooks (audiobooks)You can also perform this operation by turningLEVER.Playing1When a song is selected, press M.C.Viewing a list of songs in the selected category1When a category is selected, press M.C.Playing a song in the selected category1When a category is selected, press and hold M.C.Searching the list by alphabet1When a list for the selected category is displayed,press to switch to alphabet search mode.2Turn M.C. to select a letter.3Press M.C. to display the alphabetical list.Notes!You can play playlists created with the PC ap-plication (MusicSphere). The application willbe available on our website.!Playlists that you created with the PC applica-tion (MusicSphere) are displayed in abbre-viated form.Playing songs related to thecurrently playing songYou can play songs from the following lists.•Album list of the currently playing artist•Song list of the currently playing album•Album list of the currently playing genre1 Press and hold M.C. to switch to linkplay mode.2 Turn M.C. to change the mode; press toselect.!Artist –Plays an album of the artist cur-rently being played.!Album –Plays a song from the album cur-rently being played.!Genre –Plays an album from the genrecurrently being played.The selected song/album will be played afterthe currently playing song.Notes!The selected song/album may be canceled ifyou operate functions other than link search(e.g. fast forward and reverse).!Depending on the song selected to play, theend of the currently playing song and the be-ginning of the selected song/album may becut off.Operating this unit’s iPodfunction from your iPodYou can listen to the sound from your iPod ap-plications using your car’s speakers, whenAPP is selected.This function is not compatible with the follow-ing iPod models.—iPod with video—iPod nano 1st generationAPP Mode is compatible with the followingiPod models.!iPod touch 4th generation (software version4.1 or later)!iPod touch 3rd generation (software version3.0 or later)!iPod touch 2nd generation (software ver-sion 3.0 or later)!iPod touch 1st generation (software version3.0 or later)!iPod nano 6th generation (software version1.0 or later)!iPod nano 5th generation (software version1.0.2 or later)!iPhone 4 (software version 4.1 or later)!iPhone 3GS (software version 3.0 or later)!iPhone 3G (software version 3.0 or later)!iPhone (software version 3.0 or later)1Press BAND/ to switch the control mode.!iPod –This unit’s iPod function can beoperated from the connected iPod.En16Section02 Operating this unit

!APP –Play back the sound from youriPod applications.!AUDIO –This unit’s iPod function canbe operated from this unit.Function settings1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select FUNCTION.3 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.Play mode (repeat play)1Press M.C. to select a repeat play range.!Repeat One –Repeat the current song!Repeat All –Repeat all songs in the selectedlistShuffle mode (shuffle)1Press M.C. to select your favorite setting.!Shuffle Songs –Play back songs in the se-lected list in random order.!Shuffle Albums –Play back songs from arandomly selected album in order.!Shuffle OFF –Cancel random play.Shuffle all (shuffle all)1Press M.C. to turn shuffle all on.To turn off, set Shuffle mode in the FUNCTIONmenu to off.Link play (link play)1Press M.C. to display the setting mode.2Turn M.C. to change the mode; press to select.For details about the settings, refer to Playingsongs related to the currently playing song on theprevious page.Pause (pause)1Press M.C. to pause or resume.Tags transfer (Tags transfer)Transfer the tag information contained in the tunersource.1Press M.C. to store the tag information. Refer toUsing iTunes tagging on page 11.Audiobooks (audiobook speed)1Press M.C. to select your favorite setting.!Faster –Playback at a speed faster than nor-mal!Normal –Playback at normal speed!Slower –Playback at a speed slower than nor-malSound Retriever (sound retriever)1Press M.C. to select the desired setting.OFF (off)—1—21is effective for low compression rates, and 2iseffective for high compression rates.Notes!Switching the control mode to iPod pausessong playback. Operate the iPod to resumeplayback.!The following functions are still accessiblefrom the unit even if the control mode is set toiPod/APP.—Pausing—Fast forward/reverse—Track up/down!When the control mode is set to iPod/APP,only Pause,Tags transfer orSound Retriever is available.!The browse function cannot be operated fromthis unit.Using PandoraâIMPORTANT:Requirements to access the Pandora music ser-vice using the Pioneer car audio/video products:!Apple iPhone (first generation), iPhone 3G,iPhone 3GS, iPhone 4G, iPod touch 1G, iPodtouch 2G, iPod touch 3G or iPod touch 4G(firmware version 3.0 or later).Certain firmware versions for the iPod touchand iPhone may not be compatible with thePandora application. If this appears to be thecase, please update the firmware to a versionthat is compatible with Pandora.En 17Section02Operating this unitOperating this unit

!Latest version of the Pandora application forthe iPhone, downloaded to your device.(Search Apple iTunes App Store for“Pandora”).!Current Pandora account (Free account andpaid accounts available from Pandora; createa free account online athttp://www.pandora.com/register or throughthe Pandora application for the iPhone).!iPhone Data Plan.Note: If the Data Plan for your iPhone doesnot provide for unlimited data usage, addi-tional charges from your carrier may apply foraccessing the Pandora service via 3G and/orEDGE networks.!Connection to the Internet via 3G, EDGE or Wi-Fi network.!Optional Pioneer adapter cable connectingyour iPhone to the Pioneer car audio/videoproducts.Limitations:!Access to the Pandora service will depend onthe availability of a cellular and/or Wi-Fi net-work for purposes of allowing your iPhone toconnect to the Internet.!Ability of the Pioneer car audio/video productsto access the Pandora service is subject tochange without notice and could be affectedby any of the following: compatibility issueswith future firmware versions of iPhones;compatibility issues with future firmware ver-sions of the Pandora application for theiPhone; changes to the Pandora music serviceby Pandora; discontinuation of the Pandoramusic service by Pandora.!Certain functionality of the Pandora service isnot available when accessing the servicethrough the Pioneer car audio/video products,including, but not limited to, creating new sta-tions, deleting stations, emailing current sta-tions, buying tracks from iTunes, viewingadditional text information, logging in toPandora, and adjusting Cell Network AudioQuality.Pandora Internet radio is a music service not af-filiated with Pioneer. More information is avail-able at http://www.pandora.com.You can play the Pandora by connecting youriPod which was installed the Pandora applica-tion.Notes!Two iPods can be connected to this unit at thesame time. Settings are the same as those forPandora1 and Pandora2.!If there are two iPods connected to this unit,the iPod connected to the input of the se-lected source is the one that is operated.!Disconnect communications for the selectediPod before switching to operation of the otheriPod.Basic operations64 5 731 21Thumbs Up/Thumbs Down indicator2QuickMix indicator3PLAY/PAUSE indicator4S.Rtrv indicatorAppears when Sound Retriever function is on.5Song time (progress bar)6Play time indicator7Voltage indicatorShows the battery voltage.!The level displayed on the voltage indi-cator may differ from the actual voltagelevel.Playing tracks1Connect an iPod to the USB cable using an iPodDock Connector.2Start up the Pandora application installed on theiPod.Giving a Thumbs Up1Press to give a “Thumbs Up”for the track cur-rently playing.En18Section02 Operating this unit

Giving a Thumbs Down1Press to give a “Thumbs Down”for the trackcurrently playing and to skip to the next track.Skipping tracks1Turn LEVER to the right.Displaying text informationSelecting the desired text information1Press /DISP.Selecting and playing theQuickMix/station list1 Press (list) to switch to the Quick-Mix/station list mode.2 Use M.C. to select the QuickMix or de-sired station.Changing the sort order1Press (list).!ABC –You can sort the items in the list alphabeti-cally!DATE –You can sort the items in the list in orderof the dates on which the items were createdChanging QuickMix or stations1Turn M.C.Playing1When QuickMix or the station is selected, pressM.C.Function settings1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select FUNCTION.3 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.Bookmark (bookmark)1Press M.C. to store track information.Pause (pause)1Press M.C. to pause or resume.Sound Retriever (sound retriever)1Press M.C. to select the desired setting.1—2—OFF (off)1is effective for low compression rates, and 2iseffective for high compression rates.Audio adjustmentsOperation modesThis unit features two operation modes: the 3-way network mode (NW) and the standardmode (STD). You can switch between modesas desired. Initially, the DSP setting is set tothe standard mode (STD). (Refer to Switchingthe DSP setting mode on page 5.)!The 3-way network mode (NW) lets you cre-ate a 3-way multi-amp, multi-speaker sys-tem with separate speakers forreproduction of high, middle and low fre-quencies (bands), each driven by a dedi-cated power amp. The 3-way network modeprovides network and time alignment func-tions, two functions essential for a multi-amp, multi-speaker system, to enable pre-cise control over settings for each fre-quency range.!The standard mode (STD) lets you create a4-speaker system with front and rear speak-ers, or a 6-speaker system with front andrear speakers and subwoofers.ImportantThis unit's audio settings will continue to remainin the memory even if the battery is disconnectedor the microprocessor reset. If you want to resetthe audio settings, refer to AUDIO reset (audioreset) on page 36.Operation mode marksThis manual uses the following marks to makethe description clear.En 19Section02Operating this unitOperating this unit

: This mark indicates a function only in3-way network mode or an operation in 3-waynetwork mode.: This mark indicates a function availableonly in standard mode or an operation in stan-dard mode.!The functions and operations which do notcarry either mark are commonly used inthe 3-way network mode and standardmode.3-way network modeAdjusting the audio easilyBy carrying out the following settings/adjust-ments in the order shown, you can effortlesslycreate a finely-tuned sound field.1Using the position selector (POSI)2Auto TA and EQ (auto-time alignment and auto-equalizing)3Using balance adjustment (BAL)4Recalling equalizer curvesAdjusting the audio finelyBy carrying out the following settings/adjust-ments in the order shown, you can effortlesslycreate a finely-tuned sound field.1Adjusting time alignment (TA1,TA2)2Adjusting network (NW 1,NW 2,NW 3,NW 4)3Adjusting equalizer curves (EQ 1)4Adjusting the 16-band graphic equalizer (EQ 2)Standard modeAdjusting the audio easilyThe following functions let you easily adjustyour audio system to match the car interioracoustic characteristics, which vary depend-ing on the type of car.1Using the position selector (POSI)2Auto TA and EQ (auto-time alignment and auto-equalizing)3Using fader/balance adjustment (F/B)4Recalling equalizer curvesAdjusting the audio finelyBy carrying out the following settings/adjust-ments in the order shown, you can effortlesslycreate a finely-tuned sound field.1Using time alignment (TA1,TA2)2Using subwoofer output (SW 1)3Adjusting subwoofer settings (SW 2)4Adjusting low pass filter attenuation slope(SW 3)5Setting the high pass filter for front speakers(F.HPF 1,F.HPF 2)6Setting the high pass filter for rear speakers(R.HPF 1,R.HPF 2)7Adjusting equalizer curves (EQ 1)8Adjusting the 16-band graphic equalizer (EQ 2)Extra functionsThese functions are helpful in adjusting thesound to suit your system or your personalpreferences.!Adjusting loudness (Loudness)!Adjusting source levels (SLA)!Using automatic sound levelizer (ASL)En20Section02 Operating this unit

Introduction of audio adjustments11Audio display1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select AUDIO.3 Turn M.C. to select the audio function.After selecting, perform the following proce-dures to set the audio function.3-way network modeBAL (balance adjustment)—NW 1 (networkadjustment 1)—NW 2 (network adjustment 2)—NW 3 (network adjustment 3)—NW 4 (net-work adjustment 4)—POSI (position selector)—TA1 (time alignment setting)—TA2 (timealignment adjusting)—Loudness (loudness)—EQ 1 (graphic equalizer)—EQ 2 (16-bandgraphic equalizer)—A.EQ (auto-equalizer on/off)—ASL (automatic sound levelizer)—SLA(source level adjustment)Standard modeF/B (balance adjustment)—POSI (position se-lector)—TA1 (time alignment setting)—TA2(time alignment adjusting)—Loudness (loud-ness)—EQ 1 (graphic equalizer)—EQ 2 (16-band graphic equalizer)—SW 1 (subwooferon/off)—SW 2 (subwoofer cut-off frequency)—SW 3 (subwoofer slope)—F.HPF 1 (front highpass filter slope)—F.HPF 2 (front high pass fil-ter cut-off frequency)—R.HPF 1 (rear highpass filter slope)—R.HPF 2 (rear high pass fil-ter cut-off frequency)—A.EQ (auto-equalizeron/off)—ASL (automatic sound levelizer)—SLA (source level adjustment)4 Press M.C. to display the setting mode.#You can also switch between the audio func-tions in reverse order by turning M.C. counter-clockwise.#When selecting FM as the source, you cannotswitch to SLA.#When selecting TA OFF in TA1, you cannotswitch to TA2.#You can select SW 2 and SW 3 only when sub-woofer output is turned on in SW 1.#To return to the display of each source, pressBAND/.Notes!If you do not operate the audio function withinabout 30 seconds, the display is automaticallyreturned to the source display.!EQ 2 (16-band graphic equalizer), TA2 (timealignment adjusting), NW 1 (network adjust-ment 1), NW 2 (network adjustment 2), NW 3(network adjustment 3) and NW 4 (networkadjustment 4) functions are not canceledautomatically.Switching left and right channelYou can adjust following functions for left andright channel independently or commonly.3-way network mode!Adjusting network (NW 1,NW 2,NW 3)!Adjusting the 16-band graphic equalizer(EQ 2)Standard mode!Adjusting subwoofer settings (SW 2)!Adjusting low pass filter attenuation slope(SW 3)!Setting the high pass filter for front speakers(F.HPF 1,F.HPF 2)!Setting the high pass filter for rear speakers(R.HPF 1,R.HPF 2)!Adjusting the 16-band graphic equalizer(EQ 2)1 Use M.C. to select the audio functiondescribed above.En 21Section02Operating this unitOperating this unit

2 Press M.C. and hold to switch betweenleft/right common mode and left/right in-dependent mode.L/R (left/right common mode)—Left (left)—Right (right)3 Adjust these functions as desired.Using the position selectorOne way to assure a more natural sound is toclearly position the stereo image, putting youright in the center of the sound field. The posi-tion selector function lets you automaticallyadjust the speakers’output levels and insertsa delay time to match the number and posi-tion of occupied seats.1 Use M.C. to select POSI in the audiofunction menu.Refer to Introduction of audio adjustments onthe previous page.2 Turn LEVER to select a listening posi-tion.OFF (off)—FL (front seat left)—FR (front seatright)—Front (front seats)—All (all seats)Using balance adjustmentYou can select a balance setting that providesan ideal listening environment in all occupiedseats.!This function is only available in 3-way net-work mode .1 Use M.C. to select BAL.Refer to Introduction of audio adjustments onthe previous page.2 Turn LEVER to adjust the left/rightspeaker balance.Left 25 to Right 25 is displayed as the left/right speaker balance moves from left to right.Using fader/balance adjustmentYou can change the fader/balance setting toprovide an ideal listening environment for allof the occupied seats.!This function is only available in standardmode .1 Use M.C. to select F/B.Refer to Introduction of audio adjustments onthe previous page.2 Turn LEVER to adjust the front/rearspeaker balance.Front 25 to Rear 25 is displayed as the front/rear speaker balance moves from front to rear.#Select F/R 00 when only using two speakers.3 Press M.C. to display the left/rightspeaker balance mode.4 Turn LEVER to adjust the left/rightspeaker balance.Left 25 to Right 25 is displayed as the left/right speaker balance moves from left to right.Using time alignmentThe distance between the listening positionand each speaker can be adjusted with thisfunction.1 Use M.C. to select TA1 in the audiofunction menu.Refer to Introduction of audio adjustments onthe previous page.2 Turn LEVER to select the time align-ment.Initial (initial)—Custom (custom)—Auto TA(auto-time alignment)—TA OFF (off)!Initial is the factory supplied time align-ment.!Custom is an adjusted time alignment thatyou can create for yourself.!Auto TA is the time alignment created byauto TA and EQ. (Refer to Auto TA and EQ(auto-time alignment and auto-equalizing)on page 29.)En22Section02 Operating this unit

#You cannot select Auto TA if auto TA and EQhas not been carried out. In this case,Please set Auto TA appears.Adjusting time alignmentThe distance between the selected positionand each speaker can be adjusted.!An adjusted time alignment is memorizedin Custom.1 Use M.C. to select TA 1.Refer to Introduction of audio adjustments onpage 21.2 Press M.C. to select a unit of distance.(cm) (centimeter)—(inch) (inch)3 Press /DISP to display the upper tier.4 Use M.C. to select TA2.Refer to Introduction of audio adjustments onpage 21.#Can't Adjust TA. Set POS. FL/FR appearswhen neither FL nor FR is selected in the positionselector mode (POSI).#When selecting TA OFF in TA1, you cannotswitch to TA2.5 Turn M.C. to select the speaker to beadjusted.3-way network modeHigh L (high-range left)—High R (high-rangeright)—Mid L (middle-range left)—Mid R(middle-range right)—Low L (low-range left)—Low R (low-range right)Standard modeFront L (front left)—Front R (front right)—Rear R (rear right)—Rear L (rear left)—SubW. L (subwoofer left)—SubW. R (subwoo-fer right)#You cannot select SubW. L and SubW. Rwhen the subwoofer output is off.6 Turn LEVER to adjust the distance be-tween the selected speaker and the listen-ing position.400.0cm to 0.0cm is displayed as the distanceis increased or decreased, if you have selectedcentimeters ((cm)).160inch to 0inch is displayed as the distanceis increased or decreased, if you have selectedinches ((inch)).#You can adjust the distance for the otherspeakers in the same way.7 Press BAND/ to cancel the time align-ment mode.About the network functionThe network function lets you divide the audiosignal into different frequency bands, andthen reproduce each of them through sepa-rate speaker units.You can then make precise adjustments to thereproduced frequency band (with a low-passfilter or high-pass filter), level, phase and otherparameters to match the characteristics ofeach speaker unit.En 23Section02Operating this unitOperating this unit

Adjustable parametersThe network function enables adjustment ofthe following parameters. Make adjustmentsin line with the reproduced frequency bandand characteristics of each connected speakerunit.Reproduced frequency bandPassSlope (dB/oct.)Frequency(Hz)LevelLevel(dB)Cut-off frequency of LPFCut-off frequency of HPFReproduced frequency bandAdjusting the HPF (high-pass filter) or LPF(low-pass filter) cut-off frequency lets you setthe reproduced frequency band for eachspeaker unit.!The HPF cuts frequencies (low) below theset frequency, letting high frequenciesthrough.!The LPF cuts frequencies (high) above theset frequency, letting low frequenciesthrough.LevelThe difference in reproduced levels betweenspeaker units can be corrected.SlopeAdjusting the HPF/LPF slope (filter attenuationslope) lets you adjust the continuity of soundbetween speaker units.!The slope indicates the number of decibels(dB) the signal is attenuated when the fre-quency is one octave higher (lower) (Unit:dB/oct.). The steeper the slope, the morethe signal is attenuated.PhaseYou can switch phase (normal, reverse) foreach speaker unit’s input signal. When thecontinuity of sound between speakers is im-precise, try switching phase. This may improvethe continuity of sound between speakers.Points concerning network adjustmentsCut-off frequency adjustment!With the low-range speaker installed in therear tray, if you set Low LPF cut-off fre-quency high, bass sound is separated sothat it appears to come from the rear. Youare recommended to set Low LPF cut-offfrequency to 100 Hz or lower.!The maximum input power setting for mid-dle-range and high-range speakers isusually lower than low-range speakers.Please be aware that if the Mid HPF orHighHPF cut-off frequency is set lowerthan required, strong bass signal inputmay damage the speaker.Level adjustmentThe basic frequencies of many musical instru-ments are in the middle range. First performmiddle-range level adjustment, followed byhigh-range and then low-range level adjust-ment in that order.Slope adjustment!If you set a small absolute value for theslope (for a gentle slope), interference be-tween adjacent speaker units can easily re-sult in degraded frequency response.!If you set a large absolute value for theslope (for a steep slope), continuity ofsound between speaker units is degraded,and sounds appear to be separated.!If you set the slope to 0 dB/oct. (pass), theaudio signal bypasses the filter, so the filterdoes not have an effect.En24Section02 Operating this unit

Phase adjustmentWhen the cross-over point value for filters onboth sides is set to –12 dB/oct., the phase isreversed 180 degrees at the filter cut-off fre-quency. In this case, reversing the phase as-sures improved sound continuity.Normal phase Reverse phaseCrossover pointMuting the speaker unit (filter)You can mute each speaker unit (filter). Whena speaker unit (filter) is muted, no sound isoutputted from that speaker.!If you mute the selected speaker unit (fil-ter), MUTE blinks and no adjustments arepossible.!Even if any speaker unit (filter) is muted,you can adjust the parameters for otherspeaker units (filters).1 Use M.C. to select NW 1.Refer to Introduction of audio adjustments onpage 21.2 Turn LEVER to select the speaker unit(filter) to be adjusted.Low LPF (low-range speaker LPF)—Mid HPF(middle-range speaker HPF)—Mid LPF (mid-dle-range speaker LPF)—HighHPF (high-rangespeaker HPF)3 Press M.C. to mute the selected speakerunit (filter).MUTE blinks in the display.#To cancel the muting, press M.C. again.Adjusting network1 Use M.C. to select NW 1.Refer to Introduction of audio adjustments onpage 21.2 Turn LEVER to select the speaker unit(filter) to be adjusted.Low LPF (low-range speaker LPF)—Mid HPF(middle-range speaker HPF)—Mid LPF (mid-dle-range speaker LPF)—HighHPF (high-rangespeaker HPF)3 Press /DISP to display the upper tier.4 Use M.C. to select NW 2.Refer to Introduction of audio adjustments onpage 21.5 Turn M.C. to select the cut-off fre-quency (crossover frequency) of the se-lected speaker unit (filter).Low LPF:25—31.5—40—50—63—80—100—125—160—200—250 (Hz)Mid HPF:25—31.5—40—50—63—80—100—125—160—200—250 (Hz)Mid LPF:1.25k—1.6k—2k—2.5k—3.15k—4k—5k—6.3k—8k—10k—12.5k (Hz)HighHPF:1.25k—1.6k—2k—2.5k—3.15k—4k—5k—6.3k—8k—10k—12.5k (Hz)6 Turn LEVER to adjust the level of the se-lected speaker unit (filter).±0dB to –24dB is displayed as the level is in-creased or decreased.+6dB to –24dB is displayed as the level is in-creased or decreased, only if you have se-lected Low LPF.7 Press /DISP to display the upper tier.8 Use M.C. to select NW 3.Refer to Introduction of audio adjustments onpage 21.9 Turn LEVER to select the slope of the se-lected speaker unit (filter).Low LPF:–36—–30—–24—–18—–12 (dB/oct.)Mid HPF:–24—–18—–12—–6—Pass (0)(dB/oct.)Mid LPF:–24—–18—–12—–6—Pass (0)(dB/oct.)HighHPF:–24—–18—–12—–6(dB/oct.)En 25Section02Operating this unitOperating this unit

10 Press M.C. to switch the phase of theselected speaker unit (filter).NOR (normal)—REV (reverse)#You can adjust the parameters for otherspeaker units (filters) in the same way.11 Press /DISP to display the upper tier.12 Use M.C. to select NW 4.Refer to Introduction of audio adjustments onpage 21.13 Press M.C. to select stereo or monaural.Stereo (stereo)—MONO (monaural)#You can operate this procedure only whenLow LPF is selected.14 Press BAND/ to cancel the networkadjustment mode.Using subwoofer outputThis unit is equipped with a subwoofer outputwhich can be turned on or off. When a sub-woofer is connected to this unit, turn the sub-woofer output on.The subwoofer output phase can be switchedbetween normal and reverse.!This function is only available in standardmode .1 Use M.C. to select SW 1.Refer to Introduction of audio adjustments onpage 21.2 Press M.C. to turn subwoofer outputon.ON appears in the display. Subwoofer outputis now on.#To turn subwoofer output off, press M.C.again.3 Turn LEVER to select stereo or monaur-al.Stereo (stereo)—MONO (monaural)Adjusting subwoofer settingsThe cut-off frequency and output level can beadjusted when the subwoofer output is on.1 Use M.C. to select SW 2.Refer to Introduction of audio adjustments onpage 21.#When the subwoofer output is on, you can se-lect SW 2.2 Turn M.C. to select cut-off frequency.50—63—80—100—125 (Hz)Only frequencies lower than those in the se-lected range are outputted from the subwoo-fer.3 Turn LEVER to adjust the output levelof the subwoofer.+6 to -24 is displayed as the level is increasedor decreased.Adjusting low pass filter attenuationslopeWhen the subwoofer output is on, you can ad-just the continuity of sound between speakerunits.1 Use M.C. to select SW 3.Refer to Introduction of audio adjustments onpage 21.#When the subwoofer output is on, you can se-lect SW 3.2 Press M.C. to select the phase of sub-woofer output.NOR (normal)—REV (reverse)3 Turn LEVER to select slope.–18—–12—–6(dB/oct.)NoteWhen slope of subwoofer and high pass filter are-12dB, and same cut-off frequency, the phase isreversed 180 degrees at the cut-off frequency. Inthis case, reversing the phase assures improvedsound continuity.En26Section02 Operating this unit

Using the high pass filterWhen you do not want low sounds from thesubwoofer output frequency range to playfrom the front or rear speakers, turn on theHPF (high pass filter). Only frequencies higherthan those in the selected range are outputfrom the front or rear speakers.!This function is only available in standardmode .Muting the speaker units (filters)You can mute front and rear speaker units (fil-ters) separately. When speaker units (filters)are muted, no sound is outputted from thosespeakers.!Even if the speaker unit (filter) is muted,you can adjust the muted speaker units (fil-ters). However, mute is automatically can-celed when the level is adjusted.1 Use M.C. to select F.HPF 1 (or R.HPF 1).Refer to Introduction of audio adjustments onpage 21.2 Press M.C. to mute the selected speakerunit (filter).MUTE is displayed.#To cancel the muting, press M.C. again.Setting the high pass filter for frontspeakers1 Use M.C. to select F.HPF 1.Refer to Introduction of audio adjustments onpage 21.2 Turn LEVER to select slope.–12—–6—Pass (dB/oct.)#If you set the slope Pass (0 dB/oct.), the audiosignal bypasses the filter, so the filter does nothave an effect.3 Press /DISP to display the upper tier.4 Use M.C. to select F.HPF 2.Refer to Introduction of audio adjustments onpage 21.5 Turn M.C. to select cut-off frequency.50—63—80—100—125—160—200 (Hz)Only frequencies higher than those in the se-lected range are output from the front speak-ers.6 Turn LEVER to adjust the output levelof the front speakers.0to –24 is displayed as the level is increasedor decreased.Setting the high pass filter for rearspeakers1 Use M.C. to select R.HPF 1.Refer to Introduction of audio adjustments onpage 21.2 Turn LEVER to select slope.–12—–6—Pass (dB/oct.)#If you set the slope Pass (0 dB/oct.), the audiosignal bypasses the filter, so the filter does nothave an effect.3 Press /DISP to display the upper tier.4 Use M.C. to select R.HPF 2.Refer to Introduction of audio adjustments onpage 21.5 Turn M.C. to select cut-off frequency.50—63—80—100—125—160—200 (Hz)Only frequencies higher than those in the se-lected range are output from the rear speak-ers.6 Turn LEVER to adjust the output levelof the rear speakers.+6 to –24 is displayed as the level is increasedor decreased.Using the auto-equalizerThe auto-equalizer is the equalizer curve cre-ated by auto TA and EQ (refer to Auto TA andEQ (auto-time alignment and auto-equalizing)on page 29).You can turn the auto-equalizer on or off.En 27Section02Operating this unitOperating this unit

1 Use M.C. to select A.EQ in the audiofunction menu.Refer to Introduction of audio adjustments onpage 21.#If auto TA and EQ has not been carried out,Please set Auto EQ appears. This indicates thatyou cannot turn this function on.2 Press M.C. to turn the auto-equalizeron.Auto EQ ON appears in the display.#To turn auto-equalizer off, press M.C. again.Recalling equalizer curvesYou can adjust the equalization to match thecar’s interior acoustic characteristics as de-sired.There are seven stored equalizer curves whichyou can easily recall at any time. Here is a listof the equalizer curves.Display Equalizer curveSuper bass Super bassPowerful PowerfulNatural NaturalVocal VocalFlat FlatCustom1 Custom 1Custom2 Custom 2!Custom1 and Custom2 are adjusted equal-izer curves that you create. Adjustmentscan be made with a 16-band graphic equal-izer.!When Flat, no changes are made to thesound. You can check the effects of theequalizer curves by switching alternativelybetween Flat and another equalizer curve.%Press EQ/DISP OFF to select the equali-zer.Press EQ/DISP OFF repeatedly to switch be-tween the following equalizers:Powerful—Natural—Vocal—Flat—Custom1—Custom2—Super bassAdjusting equalizer curvesThe factory supplied equalizer curves, with theexception of Flat, can be adjusted to a fine de-gree (nuance control).1 Use M.C. to select EQ 1.Refer to Introduction of audio adjustments onpage 21.2 Turn M.C. to select an equalizer curve.3 Turn LEVER to adjust the equalizercurve.+6 to –6is displayed as the equalizer curve isincreased or decreased.#The actual range of the adjustments are differ-ent depending on which equalizer curve is se-lected.#The equalizer curve with all frequencies set to0cannot be adjusted.Adjusting the 16-band graphicequalizerYou can adjust the level of each band for theCustom1 and Custom2 equalizer curves.!A separate Custom1 curve can be createdfor each source. If you make adjustmentswhen a curve other than Custom2 is se-lected, the equalizer curve settings will berecorded in Custom1.!ACustom2 curve that is common for allsources can be created. If you make adjust-ments when the Custom2 curve is se-lected, the Custom2 curve will be updated.1 Recall the equalizer curve you want toadjust.Refer to Recalling equalizer curves on thispage.2 Use M.C. to select EQ 2.Refer to Introduction of audio adjustments onpage 21.En28Section02 Operating this unit

3 Turn M.C. to select the equalizer bandto adjust.20—31.5—50—80—125—200—315—500—800—1.25k—2k—3.15k—5k—8k—12.5k—20k (Hz)4 Turn LEVER to adjust the level of theequalizer band.+6 to –6is displayed as the level is increasedor decreased.#You can then select another band and adjustthe level.5 Press BAND/ to cancel the 16-bandgraphic equalizer adjustment.Adjusting loudnessLoudness compensates for deficiencies in thelow-frequency and high-frequency ranges atlow volume.1 Use M.C. to select Loudness in theaudio function menu.Refer to Introduction of audio adjustments onpage 21.2 Press M.C. to turn loudness on.#To turn loudness off, press M.C. again.Adjusting source levelsWith SLA (source level adjustment), the vo-lume levels of each source can be adjusted toprevent significant differences betweensources.!Settings are based on the FM volume level,which remains unchanged.1 Compare the FM volume level with thelevel of the source you wish to adjust.2 Use M.C. to select SLA in the audiofunction menu.Refer to Introduction of audio adjustments onpage 21.3 Turn LEVER to adjust the source vo-lume.+4 to –4is displayed as the source volume isincreased or decreased.Notes!The AM volume level can also be adjustedwith this function.!The USB/SD volume level can also be ad-justed with this function.Using automatic sound levelizerDuring driving, noise in the car changes ac-cording to the driving speed and road condi-tions. The automatic sound levelizer (ASL)monitors such varying noise and automati-cally increases the volume level, if this noisebecomes greater. The sensitivity (variation ofvolume level to noise level) of ASL can be setto one of five levels.1 Use M.C. to select ASL.Refer to Introduction of audio adjustments onpage 21.2 Press M.C. to turn ASL on.#To turn ASL off, press M.C. again.3 Turn LEVER to select the desired ASLlevel.Low (low)—Mid-L (mid-low)—Mid (mid)—Mid-H (mid-high)—High (high)Auto TA and EQ (auto-timealignment and auto-equalizing)Auto-time alignment automatically adjusts thetime alignment according to the distance be-tween the listening position and each speaker.The auto-equalizer automatically measuresthe car’s interior acoustic characteristics, andthen creates an auto-equalizer curve based onthat information.En 29Section02Operating this unitOperating this unit

WARNINGAs a loud tone (noise) may be emitted from thespeakers when measuring the car’s interioracoustic characteristics, never perform auto TAor auto EQ while driving.CAUTION!Thoroughly check the conditions before per-forming auto TA and EQ as the speakers maybe damaged if these functions are performedwhen:—The speakers are incorrectly connected.(For example, when a rear speaker is con-nected as a subwoofer output.)—A speaker is connected to a power amp de-livering output higher than the speaker’smaximum input power capability.!If the microphone is placed in an unsuitableposition the measurement tone may becomeloud and measurement may take a long time,resulting in battery drainage. Be sure to placethe microphone in the specified location.Before operating the auto TA and EQfunction!Perform auto TA and EQ in a quiet place,with both the car engine and air condition-ing switched off. Also turn off any carphones or portable telephones in the car, orremove them from the car. Sounds otherthan the measurement tone (such as sur-rounding sounds, engine sound, tele-phones ringing) may prevent correctmeasurement of the car’s interior acousticcharacteristics.!Be sure to perform auto TA and EQ usingthe supplied microphone. Using anothermicrophone may prevent measurement, orresult in incorrect measurement of thecar’s interior acoustic characteristics.!In order to perform auto TA and EQ, thefront speaker must be connected.!When muting the front speaker units, autoTA and EQ cannot be carried out. (Refer topage 27.)!When this unit is connected to a poweramp with input level control, auto TA andEQ may not be possible if the power amp’sinput level is set below the standard level.!When this unit is connected to a poweramp with an LPF, turn this LPF off beforeperforming auto TA and EQ. Also set thecut-off frequency for the built-in LPF of anactive subwoofer to the highest frequency.!The time alignment value resulting fromauto TA and EQ has been calculated by acomputer and is the optimum delay timethat will give accurate results. Be sure touse the resulting value although it may dif-fer from the actual distance when:—The reflected sound within the car isstrong and delays occur.—The LPF on active subwoofers or exter-nal amps delay the lower sounds.!Auto TA and EQ changes the audio settingsas follows:—The fader/balance settings return to thecenter position. (Refer to Using fader/balance adjustment on page 22.)—The graphic equalizer curve switches toFlat. (Refer to page 28.)—When a subwoofer is connected to thisunit, it will be adjusted automatically toboth subwoofer output and high pass fil-ter setting for rear speaker.!Previous settings for auto TA and EQ will beoverwritten.!When connecting tweeters, please confirmthe tweeter’s usable frequency range.When you set the cut-off frequency, sethigher than the lowest usable frequency ofthe tweeter.!Auto TA uses higher range than 10 kHz formeasurement. Therefore, using the tweeterthat cannot reproduce 10 kHz frequencyrange may damage the tweeter. When autoTA and EQ is operated, be sure to set theappropriate cut-off frequency. Also, use thetweeter that can reproduce 10 kHz at thelowest usable frequency.En30Section02 Operating this unit

Performing auto TA and EQ1 Stop the car in a place that is quiet,close all the doors, windows and sun roof,and then turn the engine off.#If the engine is left running, the noise fromthe engine may cause incorrect auto TA and EQ.2 Fix the supplied microphone in the cen-ter of the headrest of the driver’s seat, fa-cing forward.#The auto TA and EQ may differ depending onwhere you place the microphone. If desired, placethe microphone on the front passenger seat toperform auto TA and EQ.3 Turn the ignition switch to ON or ACC.#If the air conditioner or heater is turned on,turn it off. The noise from the fan may cause in-correct auto TA and EQ.#Press SRC/OFF to turn the source on if thisunit is turned off.4 Select the position for the seat onwhich the microphone is placed.Refer to Using the position selector on page22.#If no position is selected before auto TA andEQ is started, FL is automatically selected.5 Press SRC/OFF and hold until the unitturns off.6 Press and hold EQ/DISP OFF to enterthe auto TA and EQ measurement mode.The front panel opens automatically.7 Plug the microphone into the micro-phone input jack on this unit.8 Press M.C. to start the auto TA and EQ.9 When the 10-second countdown starts,get out of the car and close the door within10 seconds.The measurement tone (noise) is outputtedfrom the speakers, and auto TA and EQ be-gins.#When all speakers are connected, auto TAand EQ is completed in about six minutes.#To stop auto TA and EQ, press M.C. again.#To cancel auto TA and EQ part way through,press BAND/.10 When auto TA and EQ is completed,Complete is displayed.When correct measurement of car interioracoustic characteristics is not possible, anerror message is displayed. (Refer to Auto TAand EQ on page 44.)11 Press BAND/ to cancel the auto TAand EQ mode.12 Store the microphone carefully in theglove compartment or another safe place.If the microphone is subjected to direct sun-light for an extended period, high tempera-tures may cause distortion, color change ormalfunction.En 31Section02Operating this unitOperating this unit

Using Bluetooth wirelesstechnologyUsing Bluetooth telephoneImportant!Since this unit is on standby to connect withyour cellular phone via Bluetooth wirelesstechnology, using it without the engine run-ning can drain the battery power.!Operations may vary depending on the kind ofcellular phone.!Advanced operations that require attentionsuch as dialing numbers on the monitor,using the phone book, etc., are prohibitedwhile driving. Park your vehicle in a safe placewhen using these advanced operations.Setting up for hands-free phoningBefore you can use the hands-free phoningfunction you must set up the unit for use withyour cellular phone.1ConnectionOperate the Bluetooth telephone connectionmenu. Refer to Connection menu operation onthis page.2Function settingsOperate the Bluetooth telephone function menu.Refer to Phone menu operation on page 35.Basic operationsMaking a phone call!Refer to Phone menu operation on page 35.Answering an incoming call1When a call is received, press M.C.Ending a call1Press .Rejecting an incoming call1When a call is received, press .Answering a call waiting1When a call is received, press M.C.Switching between callers on hold1Press M.C.Canceling call waiting1Press .Adjusting the other party’s listening volume1Turn LEVER while talking on the phone.!When private mode is on, this function is notavailable.Turning private mode on or off1Press BAND/while talking on the phone.Switching the information display1Press /DISP while talking on the phone.Notes!If private mode is selected on the cellularphone, hands-free phoning may not be avail-able.!The estimated call time appears in the display(this may differ slightly from the actual calltime).Connection menu operationImportant!Be sure to park your vehicle in a safe placeand apply the parking brake when performingthis operation.!Connected devices may not operate properly ifmore than one Bluetooth device is connectedat a time (e.g. a phone and a separate audioplayer are connected simultaneously).1 Press and hold to display the con-nection menu.#You cannot operate this step during a call.2 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.En32Section02 Operating this unit

Device list (connecting or disconnecting a devicefrom the device list)!When no device is selected in the device list, thisfunction is not available.1Press M.C. to display the setting mode.2Turn M.C. to select the name of a device you wantto connect/disconnect.!Press and hold M.C. to switch the Bluetoothdevice address and device name.3Press M.C. to connect/disconnect the selected de-vice.Once the connection is established, Connectedis displayed.Delete device (deleting a device from the device list)!When no device is selected in the device list, thisfunction is not available.1Press M.C. to display the setting mode.2Turn M.C. to select the name of a device you wantto delete.!Press and hold M.C. to switch the Bluetoothdevice address and device name.3Press M.C. to display Delete YES.4Press M.C. to delete a device information fromthe device list.!While this function is in use, do not turn off theengine.Add device (connecting a new device)1Press M.C. to start searching.!To cancel, press M.C. while searching.!If this unit fails to find any available cellularphones, Not found is displayed.2Turn M.C. to select a device from the device list.!Press and hold M.C. to switch the Bluetoothdevice address and device name.3Press M.C. to connect the selected device.!To complete the connection, check the devicename (Pioneer BT Unit). Enter the PIN codeon your device if necessary.!PIN code is set to 0000 as the default. Youcan change this code.!6-digit number appears on the display of thisunit. Once the connection is established, thisnumber disappears.!If you are unable to complete the connectionusing this unit, use the device to connect tothe unit.!If three devices are already paired, Device Fullis displayed and it is not possible to performthis operation. In this case, delete a paired de-vice first.Special device (setting a special device)Bluetooth devices that are difficult to establish a con-nection with are called special devices. If yourBluetooth device is listed as a special device, selectthe appropriate one.1Press M.C. to display the setting mode.!If three devices are already paired, Device Fullis displayed and it is not possible to performthis operation. In this case, delete a paired de-vice first.2Turn M.C. to display a special device. Press to se-lect.3Turn M.C. to display this unit’s device name,Bluetooth device address and PIN code.4Use a device to connect to this unit.!To complete the connection, check the devicename (Pioneer BT Unit) and enter the PINcode on your device.!PIN code is set to 0000 as the default. Youcan change this code.Auto connect (connecting to a Bluetooth deviceautomatically)1Press M.C. to turn automatic connection on oroff.Visibility (setting the visibility of this unit)To check the availability of this unit from other de-vices, Bluetooth visibility of this unit can be turnedon.1Press M.C. to turn the visibility of this unit on oroff.!While setting Special device, Bluetooth visibi-lity of this unit is turned on temporarily.Pin code input (PIN code input)To connect your device to this unit via Bluetooth wire-less technology, you need to enter a PIN code on yourdevice to verify the connection. The default code is0000, but you can change it with this function.1Press M.C. to display the setting mode.2Turn M.C. to select a number.3Press M.C. to move the cursor to the next posi-tion.4After inputting PIN code, press and hold M.C.!After inputting, pressing M.C. returns you tothe PIN code input display, and you canchange the PIN code.En 33Section02Operating this unitOperating this unit

Play (play)1Press M.C. to start playback.Stop (stop)1Press M.C. to stop the playback.Pause (pause)1Press M.C. to turn pause on.Phone menu operationImportantBe sure to park your vehicle in a safe place andapply the parking brake when performing this op-eration.1 Press to display the phone menu.2 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.Missed calls (missed call history)Dialed calls (dialed call history)Received calls (received call history)1Press M.C. to display the phone number list.2Turn M.C. to select a name or phone number.3Press M.C. to make a call.!To display details about the contact you selected,press and hold M.C.PhoneBook (phone book)!The phone book in your cellular phone will betransferred automatically when the phone is con-nected to this unit.!Depending on the cellular phone, the phone bookmay not be transferred automatically. In this case,operate your cellular phone to transfer the phonebook. The visibility of this unit should be on. Referto Visibility (setting the visibility of this unit) onpage 33.1Press M.C. to display SEARCH (alphabetical list).2Turn M.C. to select the first letter of the name youare looking for.!Press and hold M.C. to select the desiredcharacter type.3Press M.C. to display a registered name list.4Turn M.C. to select the name you are looking for.5Press M.C. to display the phone number list.6Turn M.C. to select a phone number you want tocall.7Press M.C. to make a call.Phone Function (phone function)You can set Auto answer,Ring tone and PH.B.Name view from this menu. For details, refer to Func-tion and operation on this page.Function and operation1 Display Phone Function.Refer to Phone Function (phone function) onthis page.2 Press M.C. to display the functionmenu.3 Turn M.C. to select the function.After selecting, perform the following proce-dures to set the function.Auto answer (automatic answering)1Press M.C. to turn automatic answering on or off.Ring tone (ring tone select)1Press M.C. to turn the ring tone on or off.PH.B.Name view (phone book name view)1Press M.C. to switch between the lists of names.En 35Section02Operating this unitOperating this unit

Initial settings11Function display!Shows the function status.1 Press and hold SRC/OFF until the unitturns off.2 Press M.C. and hold until the initial set-ting menu appears in the display.3 Turn M.C. to select the initial setting.After selecting, perform the following proce-dures to set the initial setting.Language select (multi-language)For your convenience, this unit equips multiple lan-guage display. You can select the language best sui-ted to your first language.1Press M.C. to select the language.English—Français—EspañolCalendar (setting the date)1Press M.C. to select the segment of the calendardisplay you wish to set.Year—Day—Month2Turn M.C. to set the date.Clock (setting the clock)1Press M.C. to select the segment of the clock dis-play you wish to set.Hour—Minute2Turn M.C. to adjust the clock.EngineTime alert (elapsed time display setting)This setting allows you to measure the length of timethat elapses from when the machine is turned on anddisplay the amount of elapsed time per set period.Also, you will hear alarm.1Press M.C. to select your favorite setting.OFF—15Minutes—30MinutesMusic browse (music browse)When operating external storage devices (USB, SD),you can select files from the list.1Press M.C. to select the setting.OFF—USB memory1—USB memory2—SD cardWarning tone (warning tone setting)If the front panel is not detached from the head unitwithin four seconds of turning off the ignition, a warn-ing tone sounds. You can turn off the warning tone.1Press M.C. to turn the warning tone on or off.AUX1 (front AUX input setting)/AUX2 (rear RCAinput setting)Activate this setting when using an auxiliary deviceconnected to this unit.1Press M.C. to turn auxiliary setting on or off.Dimmer (dimmer setting)To prevent the display from being too bright at night,the display is automatically dimmed when the car’sheadlights are turned on. You can turn the dimmer onor off.1Press M.C. to turn dimmer on or off.Contrast (display contrast setting)1Press M.C. to select the setting mode.2Turn M.C. to adjust the contrast level.0to 15 is displayed as the level is increased or de-creased.Digital ATT (digital attenuator)When listening to a CD or other source on which therecording level is high, setting the equalizer curvelevel to high may result in distortion. You can switchthe digital attenuator to low to reduce distortion.!Sound quality is better at the high setting so thissetting is usually used.1Press M.C. to select the setting.HIGH (high)—LOW (low)AUDIO reset (audio reset)You can reset all audio functions.1Press M.C.Does it RESET? appears in the display.2Press M.C.3Turn M.C. to select desired setting.Are You Sure? appears in the display.4Press M.C.Complete appears in the display and audio func-tions are reset.!To cancel this function on the way, press BAND/.Internal AMP (power amp setting)En36Section02 Operating this unit

This unit features high power amplifier. However, inparticular system, external amplifiers are used in-stead of internal amplifier. If you use external ampli-fiers in order to establish a multi-amp system, anddon't use internal amplifier, it is recommended to turnoff the internal amplifier. Turning off internal amplifierreduces the noise that comes from the behavior of in-ternal amplifier.1Press M.C. to turn the internal power amplifier onor off.Demonstration (demo display setting)1Press M.C. to turn the demo display on or off.Ever-scroll (scroll mode setting)When ever scroll is set to ON, recorded text informa-tion scrolls continuously in the display. Set to OFF ifyou prefer the information to scroll just once.1Press M.C. to turn the ever scroll on or off.BT AUDIO (Bluetooth audio activation)You need to activate the BT Audio source in order touse a Bluetooth audio player.1Press M.C. to turn the BT Audio source on or off.Clear memory (resetting the Bluetooth wireless tech-nology module)Bluetooth device data can be deleted. To protect per-sonal information, we recommend deleting this databefore transferring the unit to other persons. The fol-lowing settings will be deleted.!phone book entries on the Bluetooth telephone!preset numbers on the Bluetooth telephone!registration assignment of the Bluetooth tele-phone!call history of the Bluetooth telephone!information of the connected Bluetooth telephone!PIN code of the Bluetooth device1Press M.C. to show the confirmation display.YES is displayed. Clearing memory is now onstandby.If you do not want to reset phone memory, turnM.C. to display CANCEL and press to select.2Press M.C. to clear the memory.Cleared is displayed and the settings are deleted.!While this function is in use, do not turn offthe engine.BT Version info. (Bluetooth version display)You can display the system versions of this unit andof Bluetooth module.S/W UPDATE (updating the bluetooth software)This function is used to update this unit with the lat-est bluetooth software. For about bluetooth softwareand updating, refer to our website.!Never turn the unit off while the bluetooth soft-ware is being updated.1Press M.C. to display the data transfer mode.Follow the on-screen instructions to finish updat-ing the bluetooth software.Other functionsUsing AUX1 and AUX2 sourceAbout AUX1 and AUX2There are two methods to connect auxiliary de-vices to this unit.AUX1 sourceWhen connecting auxiliary device using thefront AUX input.!You need to activate the AUX setting in theinitial setting menu. Refer to AUX1 (frontAUX input setting)/AUX2 (rear RCA inputsetting) on the previous page.1 Insert the mini plug into the AUX inputjack on this unit.For more details, refer to Head unit on page 7.This auxiliary device is automatically set toAUX1.2 Press SRC/OFF to select AUX1 as thesource.AUX2 sourceWhen connecting auxiliary device using therear RCA input.!You need to activate the AUX setting in theinitial setting menu. Refer to AUX1 (frontAUX input setting)/AUX2 (rear RCA inputsetting) on the previous page.En 37Section02Operating this unitOperating this unit

1 Use the rear RCA input to connect anauxiliary device.For more details, refer to the installation man-ual.This auxiliary device is automatically set toAUX2.2 Press SRC/OFF to select AUX2 as thesource.Using different entertainmentdisplaysYou can enjoy entertainment displays while lis-tening to each sound source.Switching the display indication1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ENTERTAINMENT.3 Turn M.C. to select the function.4 Press M.C. to display the Background.5 Turn M.C. to change the display.Background visual—genre—background pic-ture 1—background picture 2—backgroundpicture 3—background picture 4—spectrumanalyzer1—spectrum analyzer2—level indica-tor—level meter—simple display—moviescreen —calendar#Genre display changes depending on thegenre of music.#Genre display may not operate correctly de-pending on the application used to encode audiofiles.Turning the clock display on or off1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ENTERTAINMENT.3 Turn M.C. to select the function.Select the clock setting.4 Press M.C. to select the desired setting.Clock display—elapsed time display—clockoffSelecting the illumination colorThis unit is equipped with multiple-color illu-mination. You can select desired colors for thekeys and display of this unit. You also can cus-tomize the colors you want to use.Selecting the key color from theillumination color listYou can select desired colors for the keys ofthis unit.1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ILLUMI.3 Turn M.C. to display Key and press toselect.4 Turn M.C. to select the illuminationcolor.You can select one option from the followinglist.!27 preset colors (WHITE to ROSE)!SCAN (cycle through all colors)!Three sets of colors (WARM,AMBIENT,CALM)!CUSTOM (customized illumination color)Notes!When SCAN is selected, the system automati-cally cycles through the 27 preset colors.!When WARM is selected, the system automa-tically cycles through the warm colors.!When AMBIENT is selected, the system auto-matically cycles through the ambient colors.!When CALM is selected, the system automati-cally cycles through the calm colors.!When CUSTOM is selected, the customizedcolor saved is selected.En38Section02 Operating this unit

Selecting the display color from theillumination color listYou can select the desired colors for the dis-play of this unit.1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ILLUMI.3 Turn M.C. to switch to Display andpress to select.4 Turn M.C. to select the illuminationcolor.You can select one option from the followinglist.!27 preset colors (WHITE to ROSE)!SCAN (cycle through all colors)!Three sets of colors (WARM,AMBIENT,CALM)!CUSTOM (customized illumination color)NoteFor details about colors on the list, refer to Select-ing the key color from the illumination color list onthe previous page.Selecting key and display color fromthe illumination color listYou can select the desired colors for the keysand display of this unit.1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ILLUMI.3 Turn M.C. to display Key & Display andpress to select.4 Turn M.C. to select the illuminationcolor.You can select one option from the followinglist.!27 preset colors (WHITE to ROSE)!SCAN (cycle through all colors)!Three sets of colors (WARM,AMBIENT,CALM)Notes!You cannot select CUSTOM in this function.!Once you select a color in this function, colorson the keys and display of this unit automati-cally switch to the color you selected.!For details about colors on the list, refer to Se-lecting the key color from the illumination colorlist on the previous page.Customizing the illumination color1 Press M.C. to display the main menu.2 Turn M.C. to change the menu optionand press to select ILLUMI.3 Turn M.C. to display Key or Display.Press to select.4 Press M.C. and hold until the customiz-ing illumination color setting appears inthe display.5 Press M.C. to select the primary color.R(red)—G(green)—B(blue)6 Turn M.C. to adjust the brightness level.Adjustment range: 0to 60#You cannot select a level below 20 for all threeof R(red), G(green), and B(blue) at the sametime.#You can also perform the same operation onother colors.Notes!You cannot create a custom illumination colorwhen SCAN or a set of colors (WARM,AMBIENT,orCALM) is selected.!You can create custom illumination colors forboth Key and Display.En 39Section02Operating this unitOperating this unit

Switching the displayindication and buttonilluminationDisplay indication and button illumination canbe switched on or off.%Press and hold EQ/DISP OFF.Pressing and holding EQ/DISP OFF switchesthe display indication and button illuminationon or off.#Even if the display indication is turned off, op-eration can be conducted. If operation is con-ducted while the display indication is off, displaywill light up for a few seconds and then turn offagain.En40Section02 Operating this unit

TroubleshootingSymptom Cause ActionThe displayautomaticallyreturns to theordinary dis-play.You did not per-form any opera-tion within about30 seconds.Perform operationagain.The repeat playrange changesunexpectedly.Depending onthe repeat playrange, the se-lected range maychange when an-other folder ortrack is being se-lected or duringfast forwarding/reversing.Select the repeatplay range again.A subfolder isnot playedback.Subfolders can-not be playedwhen Folder re-peat (folder re-peat) is selected.Select another re-peat play range.NO XXXX ap-pears when adisplay is chan-ged (NO TITLE,for example).There is no em-bedded text infor-mation.Switch the displayor play anothertrack/file.The displayscreenchanges at ran-dom.Demo mode ison.!Press and hold/DISP to canceldemo mode.!Turn off thedemo display set-ting.The displayscreenchanges at ran-dom instead ofdisplaying theclock continu-ously even withthe clock dis-play turned on.Demo mode ison.!Press and hold/DISP to canceldemo mode.!Turn off thedemo display set-ting.The displayscreenchanges at ran-dom even withthe display offturned on.Demo mode ison.!Press and hold/DISP to canceldemo mode.!Turn off thedemo display set-ting.Symptom Cause ActionThe display in-dication doesnot turn offwhen EQ/DISPOFF is pressedand held down.Demo mode ison.!Press and hold/DISP to canceldemo mode.!Turn off thedemo display set-ting.The unit is mal-functioning.There is inter-ference.You are using adevice, such as acellular phone,that transmitselectric wavesnear the unit.Move electrical de-vices that may becausing the inter-ference away fromthe unit.The soundfrom theBluetoothaudio source isnot playedback.There is a call inprogress on aBluetooth con-nected cellularphone.The sound will beplayed back whenthe call is termi-nated.A Bluetooth con-nected cellularphone is cur-rently being oper-ated.Do not operate thecellular phone atthis time.A call was madewith a Bluetoothconnected cellu-lar phone andthen immediatelyterminated. As aresult, communi-cation betweenthis unit and thecellular phonewas not termi-nated properly.Reconnect theBluetooth connec-tion between thisunit and the cellu-lar phone.Text informa-tion cannot bescrolled.Display scrollingis stopped auto-matically whenthe temperaturearound this unitis 50°F or less.Wait until it warmsback up.Movie playbackis stopped andthe simple dis-play appears.Movie playbackis stopped auto-matically whenthe temperaturearound this unitis 50°F or less.Wait until it warmsback up.En 41AppendixAdditional informationAdditional information

Symptom Cause ActionSound from theiPod cannot beheard.The audio outputdirection mayswitch automati-cally when theBluetooth andUSB connectionsare used at thesame time.Use the iPod tochange the audiooutput direction.Error messagesWhen you contact your dealer or your nearestPioneer Service Center, be sure to note theerror message.CD playerMessage Cause ActionERROR-07, 11,12, 17, 30The disc is dirty. Clean the disc.The disc isscratched.Replace the disc.ERROR-10, 11,12, 15, 17, 30,A0There is an elec-trical or mechan-ical error.Turn the ignitionswitch OFF andback ON, or switchto a differentsource, then backto the CD player.ERROR-15 The inserted discis blank.Replace the disc.ERROR-23 Unsupported CDformat.Replace the disc.FORMATREADSometimes thereis a delay be-tween the start ofplayback andwhen you start tohear any sound.Wait until the mes-sage disappearsand you hearsound.NO AUDIO The inserted discdoes not containany playablefiles.Replace the disc.SKIPPED The inserted disccontains DRMprotected files.Replace the disc.PROTECT All the files onthe inserted discare embeddedwith DRM.Replace the disc.External storage device (USB, SD)/iPodMessage Cause ActionNO DEVICE No USB storagedevice or iPod isconnected.Connect a compa-tible USB storagedevice/iPod.FORMATREADSometimes thereis a delay be-tween the start ofplayback andwhen you start tohear any sound.Wait until the mes-sage disappearsand you hearsound.NO AUDIO There are nosongs.Transfer the audiofiles to the USBstorage device andconnect.The connectedUSB storage de-vice has securityenabled.Follow the USBstorage device in-structions to dis-able the security.SKIPPED The connectedUSB storage de-vice containsfiles embeddedwith WindowsMediaäDRM 9/10.Play an audio filenot embedded withWindows MediaDRM 9/10.PROTECT All the files in theUSB storage de-vice are em-bedded withWindows MediaDRM 9/10.Transfer audio filesnot embedded withWindows MediaDRM 9/10 to theUSB storage de-vice and connect.NOT COMPA-TIBLEThe USB deviceconnected to isnot supported bythis unit.!Connect a USBMass StorageClass compliantdevice.!Disconnect yourdevice and replaceit with a compati-ble USB storagedevice.Non-compatibleiPodDisconnect yourdevice and replaceit with a compati-ble iPod.Non-compatibleSD storage de-viceRemove your de-vice and replace itwith a compatibleSD storage device.En42AppendixAdditional information

Message Cause ActionCHECK USB The USB connec-tor or USB cablehas short-circuited.Check that theUSB connector orUSB cable is notcaught in some-thing or damaged.The connectedUSB storage de-vice consumesmore than maxi-mum allowablecurrent.Disconnect theUSB storage de-vice and do notuse it. Turn theignition switch toOFF, then to ACCor ON and thenconnect only com-pliant USB storagedevices.The iPod oper-ates correctly butdoes not charge.Make sure the con-nection cable forthe iPod has notshorted out (e.g.,not caught inmetal objects).After checking,turn the ignitionswitch OFF andback ON, or dis-connect the iPodand reconnect.ERROR-19 Communicationfailed.!Perform one ofthe following op-erations.–Turn the ignitionswitch OFF andback ON.–Disconnect oreject the externalstorage device.–Change to a dif-ferent source.Then, return to theUSB or SD source.!Disconnect thecable from theiPod. Once theiPod’s main menuis displayed, recon-nect the iPod andreset it.iPod failure. Disconnect thecable from theiPod. Once theiPod’s main menuis displayed, recon-nect the iPod andreset it.Message Cause ActionERROR-23 USB storage de-vice was not for-matted withFAT12, FAT16 orFAT32.USB storage de-vice should be for-matted with FAT12,FAT16 or FAT32.ERROR-16 The iPod firm-ware version isold.Update the iPodversion.iPod failure. Disconnect thecable from theiPod. Once theiPod’s main menuis displayed, recon-nect the iPod andreset it.STOP There are nosongs in the cur-rent list.Select a list thatcontains songs.Not found No relatedsongs.Transfer songs tothe iPod.Bluetooth deviceMessage Cause ActionERROR-10 The power failedfor the Bluetoothmodule of thisunit.Turn the ignitionswitch OFF andthen to ACC or ON.If the error mes-sage is still dis-played afterperforming theabove action,please contactyour dealer or anauthorized PioneerService Station.PandoraMessage Cause ActionERROR-19 Communicationfailed.Disconnect thecable from theiPod. Once theiPod’s main menuis displayed, recon-nect the iPod andreset it.Start up thePandora Ap-plicationThe Pandora ap-plication has notstarted runningyet.Start up thePandora applica-tion from youriPod/iPhone.En 43AppendixAdditional informationAdditional information

Message Cause ActionTry again later Unable to savethumb rating.Unable to saveBookMark.Pandora systemis undergoingmaintenance.Try again later.Skip limitreachedSkip limitreached.Do not exceed theskip limit.Check Appli-cationThis version ofthe Pandora ap-plication is notsupported.Connect an iPod/iPhone that has acompatible versionof the Pandora ap-plication installed.Check Device Device error mes-sage displayed inPandora Applica-tion.Unable to playmusic fromPandora.Please check youriPod/iPhone.No AvailableStationNo station found. Create a station inthe Pandora appli-cation on youriPod/iPhone.No Active Sta-tionsNo station se-lected.Select a station.Auto TA and EQMessage Cause ActionERR:MIC check The microphoneis not connected.Plug the suppliedmicrophone se-curely into thejack.ERR:FrontSpeaker,ERR:Front-Lch,ERR:Front-Rch,ERR:Rear-Lch,ERR:Rear-Rch,ERR:SubW-Lch,ERR:SubW-Rch,ERR:SubWoo-ferThe microphonecannot pick upthe measuringtone of a speaker.!Confirm that thespeakers are con-nected correctly.!Cancel mutingthe front speakerunits.!Correct the inputlevel setting of thepower amp con-nected to thespeakers.!Set the micro-phone correctly.Message Cause ActionERR:OutsideNoiseThe surroundingnoise level is toohigh.!Stop your car ina place that isquiet, and switchoff the engine, airconditioner andheater.!Set the micro-phone correctly.Handling guidelinesDiscs and playerUse only discs that feature either of the following twologos.Use 12-cm discs. Do not use 8-cm discs or an adapterfor 8-cm discs.Use only conventional, fully circular discs. Do not useshaped discs.Do not insert anything other than a CD into the CDloading slot.Do not use cracked, chipped, warped, or otherwisedamaged discs as they may damage the player.Unfinalized CD-R/RW discs cannot be played back.Do not touch the recorded surface of the discs.Store discs in their cases when not in use.Do not attach labels, write on or apply chemicals tothe surface of the discs.To clean a CD, wipe the disc with a soft cloth outwardfrom the center.En44AppendixAdditional information

Condensation may temporarily impair the player’sperformance. Let it rest for about one hour to adjustto a warmer temperature. Also, wipe any damp discsoff with a soft cloth.Playback of discs may not be possible because ofdisc characteristics, disc format, recorded applica-tion, playback environment, storage conditions, andso on.Road shocks may interrupt disc playback.When using discs that can be printed on label sur-faces, check the instructions and the warnings of thediscs. Depending on the discs, inserting and ejectingmay not be possible. Using such discs may result indamage to this equipment.Do not attach commercially available labels or othermaterials to the discs.!The discs may warp making the disc unplayable.!The labels may come off during playback and pre-vent ejection of the discs, which may result in da-mage to the equipment.External storage device (USB, SD)Address any questions you have about your externalstorage device (USB, SD) to the manufacturer of thedevice.Do not leave the external storage device (USB, SD) inplaces with high temperatures.Depending on the external storage device (USB, SD),the following problems may occur.!Operations may vary.!The storage device may not be recognized.!Files may not be played back properly.USB storage deviceConnections via USB hub are not supported.Do not connect anything other than a USB storagedevice.Firmly secure the USB storage device when driving.Do not let the USB storage device fall onto the floor,where it may become jammed under the brake or ac-celerator pedal.Depending on the USB storage device, the followingproblems may occur.!The device may generate noise in the radio.SD memory cardThis unit supports only the following types of SDmemory cards.!SD!miniSD!microSD!SDHCKeep the SD memory card out of the reach of chil-dren. Should the SD memory card be swallowed, con-sult a doctor immediately.Do not touch the connectors of the SD memory carddirectly with your fingers or with any metal device.Do not insert anything other than an SD memory cardinto the SD card slot. If a metal object (such as acoin) is inserted into the slot, the internal circuits maybreak and cause malfunctions.When inserting a miniSD or microSD, use an adapter.Do not use an adapter which has metal parts otherthan the connectors exposed.Do not insert a damaged SD memory card (e.g.warped, label peeled off) as it may not be ejectedfrom the slot.Do not try to force an SD memory card into the SDcard slot as the card or this unit may be damaged.When ejecting an SD memory card, press it and holdit until it clicks. It is dangerous for you to release yourfinger immediately after you press on the card as thecard may shoot out of the slot and hit you in the face,etc. If the card shoots out of the slot, it may becomelost.iPodTo ensure proper operation, connect the dock connec-tor cable from the iPod directly to this unit.Firmly secure the iPod when driving. Do not let theiPod fall onto the floor, where it may become jammedunder the brake or accelerator pedal.About iPod settings!When an iPod is connected, this unit changes theEQ (equalizer) setting of the iPod to off in order tooptimize the acoustics. When you disconnect theiPod, the EQ returns to the original setting.!You cannot set Repeat to off on the iPod whenusing this unit. Repeat is automatically changedto All when the iPod is connected to this unit.Incompatible text saved on the iPod will not be dis-played by the unit.En 45AppendixAdditional informationAdditional information

DualDiscsDualDiscs are two-sided discs that have a recordableCD for audio on one side and a recordable DVD forvideo on the other.Since the CD side of DualDiscs is not physically com-patible with the general CD standard, it may not bepossible to play the CD side with this unit.Frequent loading and ejecting of a DualDisc may re-sult in scratches on the disc. Serious scratches canlead to playback problems on this unit. In somecases, a DualDisc may become stuck in the disc load-ing slot and will not eject. To prevent this, we recom-mend you refrain from using DualDisc with this unit.Please refer to the information from the disc manu-facturer for more detailed information aboutDualDiscs.CAUTIONDo not leave the discs/external storage device(USB, SD) or iPod in places with hightemperatures.Compressed audiocompatibility (disc, USB, SD)WMAFile extension: .wmaBit rate: 48 kbps to 320 kbps (CBR), 48 kbps to384 kbps (VBR)Sampling frequency: 32 kHz, 44.1 kHz, 48 kHzWindows Media Audio Professional, Lossless, Voice/DRM Stream/Stream with video: Not compatibleMP3File extension: .mp3Bit rate: 8 kbps to 320 kbps (CBR), VBRSampling frequency: 8 kHz to 48 kHz (32 kHz, 44.1 kHz,48 kHz for emphasis)Compatible ID3 tag version: 1.0, 1.1, 2.2, 2.3, 2.4 (ID3tag Version 2.x is given priority over Version 1.x.)M3u playlist: Not compatibleMP3i (MP3 interactive), mp3 PRO: Not compatibleWAVFile extension: .wavQuantization bits: 8 and 16 (LPCM), 4 (MS ADPCM)Sampling frequency: 16 kHz to 48 kHz (LPCM),22.05 kHz and 44.1 kHz (MS ADPCM)AACCompatible format: AAC encoded by iTunesFile extension: .m4aSampling frequency: 11.025 kHz to 48 kHzTransmission rate: 16 kbps to 320 kbps, VBRApple Lossless: Not compatibleAAC file bought from the iTunes Store (.m4p file ex-tension): Not compatibleSupplemental informationOnly the first 32 characters can be displayed as a filename (including the file extension) or a folder name.This unit may not operate correctly depending on theapplication used to encode WMA files.There may be a slight delay at the start of playback ofaudio files embedded with image data or audio filesstored on a USB storage device that has numerousfolder hierarchies.Russian text to be displayed on this unit should be en-coded in one of the following character sets:!Unicode (UTF-8, UTF-16)!A character set other than Unicode that is used ina Windows environment and is set to Russian inthe multi-language settingDiscPlayable folder hierarchy: up to eight tiers (A practicalhierarchy is less than two tiers).Playable folders: up to 99Playable files: up to 999File system: ISO 9660 Level 1 and 2, Romeo, JolietMulti-session playback: CompatibleEn46AppendixAdditional information

Packet write data transfer: Not compatibleRegardless of the length of blank sections betweenthe songs from the original recording, compressedaudio discs play with a short pause between songs.External storage device (USB, SD)Playable folder hierarchy: up to eight tiers (A practicalhierarchy is less than two tiers).Playable folders: up to 1 500Playable files: up to 15 000Playback of copyright-protected files: Not compatiblePartitioned external storage device (USB, SD): Onlythe first playable partition can be played.There may be a slight delay when starting playback ofaudio files on a USB storage device with numerousfolder hierarchies.SD memory cardThere is no compatibility for Multi Media Cards(MMC).Compatibility with all SD memory cards is not guaran-teed.This unit is not compatible with SD-Audio.CAUTION!Pioneer accepts no responsibility for data loston USB memory/USB portable audio players/SD memory cards/SDHC memory cards, evenif that data is lost while this unit is used.!Pioneer cannot guarantee compatibility withall USB mass storage devices and assumesno responsibility for any loss of data on mediaplayers, smart phones, or other devices whileusing this product.iPod compatibilityThis unit supports only the following iPod models.Supported iPod software versions are shown below.Older versions may not be supported.Made for!iPod touch 4th generation (software version 4.1)!iPod touch 3rd generation (software version 3.1.1)!iPod touch 2nd generation (software version 2.1.1)!iPod touch 1st generation (software version 1.1)!iPod classic 160GB (software version 2.0.2)!iPod classic 120GB (software version 2.0)!iPod classic (software version 1.0)!iPod with video (software version 1.2.3)!iPod nano 6th generation (software version 1.0)!iPod nano 5th generation (software version 1.0.1)!iPod nano 4th generation (software version 1.0)!iPod nano 3rd generation (software version 1.0)!iPod nano 2nd generation (software version 1.1.3)!iPod nano 1st generation (software version 1.3.1)!iPhone 4 (software version 4.1)!iPhone 3GS (software version 3.0)!iPhone 3G (software version 2.0)!iPhone (software version 1.1.1)Depending on the generation or version of the iPod,some functions may not be available.Operations may vary depending on the software ver-sion of iPod.When using an iPod, an iPod Dock Connector to USBCable is required.A Pioneer CD-IU51 interface cable is also available.For details, consult your dealer.About the file/format compatibility, refer to the iPodmanuals.Audiobook, Podcast: CompatibleCAUTIONPioneer accepts no responsibility for data lost onthe iPod, even if that data is lost while this unit isused.Sequence of audio filesThe user cannot assign folder numbers andspecify playback sequences with this unit.En 47AppendixAdditional informationAdditional information

SpecificationsGeneralPower source ............................. 14.4 V DC (10.8 V to 15.1 Vallowable)Grounding system ................... Negative typeMaximum current consumption..................................................... 10.0 ADimensions (W × H × D):DINChassis ..................... 178 mm × 50 mm ×165 mm(7 in. × 2 in. × 6-1/2 in.)Nose ........................... 188 mm × 58 mm × 17 mm(7-3/8 in.× 2-1/4 in.× 5/8 in.)DChassis ..................... 178 mm × 50 mm ×165 mm(7 in.× 2 in.× 6-1/2 in.)Nose ........................... 170 mm × 46 mm × 17 mm(6-3/4 in.× 1-3/4 in.× 5/8 in.)Weight .......................................... 1.2 kg (2.6 lbs)AudioMaximum power output ....... 50 W × 4Continuous power output ... 22 W × 4 (50 Hz to15 000 Hz, 5 % THD,4Wload, both channels dri-ven)Load impedance ...................... 4Wto 8 W×4Preout maximum output level..................................................... 5.0 VLoudness contour ................... +10 dB (100 Hz), +6.5 dB(10 kHz) (volume: –30 dB)Equalizer (Left/Right independent 16-Band GraphicEqualizer):Frequency .......................... 20 Hz/31.5 Hz/50 Hz/80 Hz/125 Hz/200 Hz/315 Hz/500 Hz/800 Hz/1.25 kHz/2 kHz/3.15 kHz/5 kHz/8 kHz/12.5 kHz/20 kHzEqualization range ........ ±12 dB (2 dB step)Auto equalizer:(Front & rear & subwoofer/High & mid & low)Frequency .......................... 20 Hz/31.5 Hz/50 Hz/80 Hz/125 Hz/200 Hz/315 Hz/500 Hz/800 Hz/1.25 kHz/2 kHz/3.15 kHz/5 kHz/8 kHz/12.5 kHz/20 kHzEqualization range ........ +6 dB to –12 dB (2 dB step)Network (standard mode):HPF (front)Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 HzSlope .......................... 0 (Pass)/–6 dB/oct./–12 dB/oct.Gain ............................ 0dBto–24 dB/Mute (1 dBstep)HPF (rear)Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 HzSlope .......................... 0 (Pass)/–6 dB/oct./–12 dB/oct.Gain ............................ +6 dB to –24 dB/Mute (1dB step)Subwoofer (stereo/mono):Frequency ................ 50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 HzSlope .......................... –6 dB/oct./–12 dB/oct./–18 dB/oct.Gain ............................ +6 dB to –24 dB/Mute (1dB step)Phase ........................ Normal/ReverseNetwork (3-way network mode):High HPF:Frequency ................ 1.25 kHz/1.6 kHz/2 kHz/2.5 kHz/3.15 kHz/4 kHz/5 kHz/6.3 kHz/8 kHz/10 kHz/12.5 kHzSlope .......................... –6 dB/oct./–12 dB/oct./–18 dB/oct./–24 dB/oct.Gain ............................ 0dBto–24 dB/Mute (1 dBstep)Phase ........................ Normal/ReverseMid HPF/LPF:Frequency (LPF) ... 1.25 kHz/1.6 kHz/2 kHz/2.5 kHz/3.15 kHz/4 kHz/5 kHz/6.3 kHz/8 kHz/10 kHz/12.5 kHzFrequency (HPF)................................. 25 Hz/31.5 Hz/40 Hz/50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 Hz/250 HzSlope (LPF) ............. 0 (Pass)/–6 dB/oct./–12 dB/oct./–18 dB/oct./–24 dB/oct.Slope (HPF) ............ 0 (Pass)/–6 dB/oct./–12 dB/oct./–18 dB/oct./–24 dB/oct.Gain ............................ 0dBto–24 dB/Mute (1 dBstep)Phase ........................ Normal/ReverseLow LPF (stereo/mono):Frequency ................ 25 Hz/31.5 Hz/40 Hz/50 Hz/63 Hz/80 Hz/100 Hz/125 Hz/160 Hz/200 Hz/250 HzSlope .......................... –12 dB/oct./–18 dB/oct./–24 dB/oct./–30 dB/oct./–36 dB/oct.En50AppendixAdditional information

Gain ............................ +6 dB to –24 dB/Mute (1dB step)Phase ........................ Normal/ReverseCD playerSystem .......................................... Compact disc audio systemUsable discs .............................. Compact discSignal-to-noise ratio ............... 105 dB (1 kHz) (IHF-A net-work)Number of channels .............. 2 (stereo)MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12(2 ch audio)(Windows Media Player)AAC decoding format ............ MPEG-4 AAC (iTunes en-coded only) (.m4a)(Ver. 9.2 and earlier)WAV signal format .................. Linear PCM & MS ADPCM(Non-compressed)USBUSB standard specification..................................................... USB 2.0 full speedMaximum current supply .... 1AUSB Class ................................... MSC (Mass Storage Class)File system .................................. FAT12, FAT16, FAT32MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12(2 ch audio)(Windows Media Player)AAC decoding format ............ MPEG-4 AAC (iTunes en-coded only) (.m4a)(Ver. 9.2 and earlier)WAV signal format .................. Linear PCM & MS ADPCM(Non-compressed)SDCompatible physical format..................................................... Version 2.00Maximum memory capacity..................................................... 32 GB (for SD and SDHC)File system .................................. FAT12, FAT16, FAT32MP3 decoding format ........... MPEG-1 & 2 Audio Layer 3WMA decoding format ......... Ver. 7, 7.1, 8, 9, 10, 11, 12(2 ch audio)(Windows Media Player)AAC decoding format ............ MPEG-4 AAC (iTunes en-coded only) (.m4a)(Ver. 9.2 and earlier)WAV signal format .................. Linear PCM & MS ADPCM(Non-compressed)FM tunerFrequency range ...................... 87.9 MHz to 107.9 MHzUsable sensitivity ..................... 9 dBf (0.8 µV/75 W, mono,S/N: 30 dB)Signal-to-noise ratio ............... 72 dB (IHF-A network)AM tunerFrequency range ...................... 530 kHz to 1 710 kHzUsable sensitivity ..................... 25 µV (S/N: 20 dB)Signal-to-noise ratio ............... 62 dB (IHF-A network)BluetoothVersion .......................................... Bluetooth 3.0 certifiedOutput power ............................ +4 dBm Maximum(Power class 2)CEA2006 SpecificationsPower output ............................. 14 W RMS × 4 Channels(4 Wand ≦1 % THD+N)S/N ratio ....................................... 91 dBA (reference: 1 W into4W)NoteSpecifications and the design are subject to mod-ifications without notice.En 51AppendixAdditional informationAdditional information

PIONEER CORPORATION1-1, Shin-ogura, Saiwai-ku, Kawasaki-shi,Kanagawa 212-0031, JAPANPIONEER ELECTRONICS (USA) INC.P.O. Box 1540, Long Beach, California 90801-1540, U.S.A.TEL: (800) 421-1404PIONEER EUROPE NVHaven 1087, Keetberglaan 1, B-9120 Melsele, Belgium/BelgiqueTEL: (0) 3/570.05.11PIONEER ELECTRONICS ASIACENTRE PTE. LTD.253 Alexandra Road, #04-01, Singapore 159936TEL: 65-6472-7555PIONEER ELECTRONICS AUSTRALIA PTY. LTD.5 Arco Lane, Heatherton, Victoria, 3202 AustraliaTEL: (03) 9586-6300PIONEER ELECTRONICS OF CANADA, INC.340 Ferrier Street, Unit 2, Markham, Ontario L3R 2Z5, CanadaTEL: 1-877-283-5901TEL: 905-479-4411PIONEER ELECTRONICS DE MEXICO, S.A. de C.V.Blvd.Manuel Avila Camacho 138 10 pisoCol.Lomas de Chapultepec, Mexico, D.F. 11000TEL: 55-9178-4270先鋒股份有限公司台北市內湖區瑞光路407號8樓電話: 886-(0)2-2657-3588先鋒電子（香港）有限公司香港九龍長沙灣道909號5樓電話: 852-2848-6488ã2011 PIONEER CORPORATION.All rights reserved.<CRB3831-A> UC<KOKZX> <11L00000>

Navigation menu

Upload a User Manual

Namespaces

Wiki Guide
HTML
PDF
Info

Views

User Manual
Discussion / Help

Navigation

© 2024 UserManual.wiki | Privacy Policy

Contact Us
DMCA