Philips Consumer Lifestyle TSU7000 ProntoPro NG - Remote Control User Manual User Guide

Philips Consumer Lifestyle ProntoPro NG - Remote Control User Guide

UserManual.wiki >

Philips Consumer Lifestyle >

TSU7000 User Manual

Users Manual

ProntoPro NG TSU7000 Home Theater Control Panel User Guide

FAQ.....................................................................................................41 Troubleshooting .................................................................................43 General Problems ................................................................................. 43 Customizing Problems ......................................................................... 43 Memory Storage Problems .................................................................. 44 ProntoPro NG error messages............................................................. 44 Connection to the PC............................................................................ 44 Maintaining ProntoPro NG .................................................................45 Important Notices................................................................................. 45 Cleaning ProntoPro NG....................................................................... 45 List of Symbols ...................................................................................46 Specifications .....................................................................................48 Glossary..............................................................................................49 Index..................................................................................................52 Copyright............................................................................................54

FCC Compliancy 4 FCC Compliancy This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rule. These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If the equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a different circuit from the receiver.  Consult the dealer or an experienced radio/TV technician for help. FCC Information for User Caution Changes or modifications made by the user not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. @@@CE Compliancy SBC RU980 Made in Belgium / Fabriqué en Belgique CE0682 (!) This device can be used in: AT BE DE DK GR ES FI FR IRE IT LU NL NO PT SE UK

Taking a First Look 5 Taking a First Look ProntoPro NG: The Home Theater Control Panel ProntoPro NG is a Home Theater Control Panel that allows maximum flexibility and customization for even the most sophisticated home entertainment system. It can control almost any device that understands infrared (IR) remote control signals. Its intuitive interface makes it a perfect remote control for every user. ProntoPro NG is easy to configure. It contains a huge universal database where IR codes are stored to control different brands for all kinds of video, audio devices and even home automation equipment. By default ProntoPro NG is set up to control Philips and Marantz devices. For other brands you simply choose the brands of your devices when you use ProntoPro NG for the first time. Furthermore the ProntoPro NG is equiped with a color touch screen. This TFT-display supports 65536 colors so you can upload any color picture. ProntoPro NG offers you some extra powerful features:  You can create and edit macros, allowing you to send a series of commands with one single touch.  You can set timers for certain actions to be carried out at predefined times, e.g switching on your lights or recording your favourite daily TV-show with your VCR.  You can choose to have ProntoPro NG working with radio frequency (RF) signals to operate devices from a distance or from an adjacent room. To do this, you need an optional RF Extender that converts ProntoPro NG RF signals into IR signals. With ProntoProEdit NG software you can create your own screens and define a personal look. ProntoProEdit NG’s Online Help system (accessible via the ‘Help’ icon in ProntoProEdit NG) will guide you through the process. You can find ProntoProEdit NG on the included CD-ROM and on the Philips website www.pronto.philips.com. See “ProntoProEdit NG” on page 40 for more information. The Device ProntoPro NG has several hard buttons. Most are freely programmable, some have a predefined function:  The buttons on the left side of ProntoPro NG of the screen have predefined functions: Page up, Page down and Backlight  The 4 firm keys below the touch screen are freely programmable. You can reprogram the function of these buttons and change the label on the touch screen.  The cursor and the OK and Home buttons on the right side of the cursor are programmed to operate devices (e.g. navigating through the on screen menu of your TV). With the Toggle button you can change the working of the cursor. The buttons on the right side of the screen are used to control the volume and channel: Channel up, Channel down, Mute, Volume up and Volume down. Although these buttons each have a predefined function, you can program them yourself. If you learn one of these buttons or assign a macro to it, its predefined function for that database will be permanently lost. Learning eye

Taking a First Look 6 The Touch Screen Channel upChannel downMuteVolume upLCD touch screen Firm keys Cursor USB port Volume downReset button Battery compartment Connection to docking stationBacklight Page down OKHome Page up Free programmable Toggle button

Taking a First Look 7 @@@ The Docking Station The docking station is used to charge the ProntoPro NG’s battery pack. When your ProntoPro NG is placed in the docking station, you can connect ProntoPro NG to your computer via the USB port of the docking station, instead of the USB port of the ProntoPro NG. Pronto Icon Device Overview buttonPage Overview buttonPrevious Device Next Device Soft buttons Labels for the firm keys USB port Adapter Connector Connector for Pronto

Taking a First Look 8 What’s New for ProntoPro Next Generation? This new ProntoPro NG (TSU7000) offers several new features compared to the previous model of ProntoPro (TSU6000). The most important ones are:  Transparency ProntoPro NG supports transparency in buttons and other objects. This makes it easier to create complex user interfaces. You can now place buttons with a transparent background on top of a background image, let transparent buttons overlap or create transparency effects within buttons.  65536 colors The number of colors has increased from 256 to 65536 (64k). Therefore the buttons look much more natural.  Integrated Macros Macros are now better integrated in the configuration file. Each button can be a macro, this means each button can contain more than one action.  More advanced Timers Your ProntoPro NG is able to set timers for certain actions to be carried out at any time you choose. Timers are not an entirely new feature of ProntoPro, but they are easier to use and better integrated with the configuration file. You can activate and deactivate the timers you created and you can also set them to repeat daily or weekly. For instance, you can have the lights switched on every day at sundown. You can also create a timer to set your VCR to record your favourite TV-show on wednesday and saturday.  Page Overview The Page Overview offers you a list of all the pages for one device. Every device comes with a Page Overview, making it easier and faster to browse through the device pages.  Cursor Navigation By default the cursor is programmed to operate devices. The functions assigned to the cursor button depend on the device active on ProntoPro NG. ProntoPro NG also offer you the possibility to use the cursor for navigating through devices and pages on the screen. The Left and Right cursor buttons allow you to scroll through the devices, with the Up and Down cursor buttons you scroll through the different pages.  Animation Mode ProntoPro NG provides navigation feedback through graphical animations of mode transitions and page transitions. You can enable and disable the animations of your ProntoPro NG in the Settings Pages.  USB ProntoPro NG is provided with a USB port. The USB port makes downloading much easier.  16 MB of Memory ProntoPro NG has 16 MegaByte of memory (extendable to 32 MB). This enables you to download larger configuration files to ProntoPro NG. .

Before You Start 9 Before You Start Placing the Battery Pack When you use ProntoPro NG for the first time, you will have to:  install the battery pack;  place ProntoPro NG in the docking station and charge it. Attention Use the docking station only with the Philips NiMH rechargeable battery pack. Never plug other appliances (like mobile phones, PDA’s, …) into the docking station. This causes damage to the connector and the appliance. Installing the Battery Pack 1 Press the latch on the battery cover and remove the battery cover from the ProntoPro NG. 2 Place the battery pack in the battery compartment. 3 Plug the cable of the battery pack in the connector. @@@ darken ProntoPro and integrate callout with plug 4 Slide the battery cover back on. Make sure the wires of the battery pack do not get stuck while sliding the cover on. After a few seconds, the ProntoPro NG starts up automatically and an Introduction screen appears. The ProntoPro NG beeps twice to indicate that it has finished starting up. Because the battery pack is not fully pre-charged, you need to charge it as described below.

Before You Start 10 Charging the ProntoPro NG For charging the ProntoPro NG, you have to place in the docking station. When the battery pack is running low, the Low Battery icon will appear on the ProntoPro NG. You can charge the ProntoPro NG at any time; the battery pack does not have to be entirely empty before recharging. Note You can continue using the ProntoPro NG while it is being charged. When the battery pack is empty, the ProntoPro NG’s settings are retained. You only need to set the clock. However, you should recharge the ProntoPro NG as soon as possible to ensure perfect performance. 1 Plug the power adapter into a wall outlet and connect it to the docking station. 2 Slide the ProntoPro NG in the docking station until it clicks. Make sure you hold the ProntoPro NG at an angle of 30° to 45° when you place it in the docking station. Charging starts immediately. The blue charging LEDs on the front of the docking station indicate that the battery pack is being charged. When the ProntoPro NG is fully charged, the charging LEDs go off. Normal charging time is 2 to 3 hours, depending on the condition of the battery pack. When the charging LEDs are flashing, an error occurs. Try one of the following:  Make sure the battery pack is properly installed in your ProntoPro NG.  Make sure the ProntoPro NG is placed properly in the docking station.  Check if the connector in the docking station is clean and free of obstructions.  Cool down the battery pack.

Getting Started 11 Getting Started Turning on ProntoPro NG ProntoPro NG can be turned on in four different ways:  Tap the touch screen. Note Only use your finger, a stylus or a blunt soft object like a pencil eraser to operate the touch screen.  Press one of the 4 firm keys below the screen to activate the display. Note When you press a hard button on ProntoPro NG, the according function will be executed immediately, while the 4 firm keys below the touch screen will activate the display.  Press the Backlight button.  Tilt ProntoPro NG more than 50 degrees. Setting Time and Date When you have installed the battery pack and turned on ProntoPro NG, you have to set the current time. Attention Every time you reset your ProntoPro NG you will have to set the time again. Changing the Time Format 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap button in the Tools Menu. The first Settings Page appears. 50°

Getting Started 12 @@@ 3 Tap the Time Format button in the first Settings Page. The Time Format button toggles between the three time formats:  12 hour (AM/PM): This is the default format;  24 hour;  No time. Changing the Time 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The first Settings Page appears. 3 Tap the Time button in the first Settings Page. The Time button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 4 To increase the time, press (and hold) the firm key labeled ‘+’. -or- To decrease the time, press (and hold) the firm key labeled ‘-’. 5 Tap the Time button again. The new time is set. Changing the Date 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The first Settings Page appears. To change the day 1 Tap the Day button in the first Settings Page. The Day button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 2 To increase the days, press (and hold) the firm key labeled ‘+’. -or- To decrease the days, press (and hold) the firm key labeled ‘-’. 3 Tap the Day button again. The new day is set.

Getting Started 13 To change the month 1 Tap the Month button in the first Settings Page. The Month button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 2 To increase the months, press (and hold) the firm key labeled ‘+’. -or- To decrease the months, press (and hold) the firm key labeled ‘-’. 3 Tap the Month button again. The new month is set. To change the year 1 Tap the Year button in the first Settings Page. The Year button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 2 To increase the years, press (and hold) the firm key labeled ‘+’. -or- To decrease the years, press (and hold) the firm key labeled ‘-’. 3 Tap the Year button again. The new year is set. Setting the Language You can change the language used on your ProntoPro NG. 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The first Settings Page appears. 3 Press the Page down hard button. The second Settings Page appears. @@@ new labels, 1 animation button 4 Tap in the second Settings Page. The Language button toggles between five languages:  English;  French;  German;  Spanish;  Dutch.

Getting Started 14 Operating ProntoPro NG ProntoPro NG contains a series of customizable devices, each consisting of several device pages. All active devices on your ProntoPro NG are listed in the Device Overview. All the available device pages are listed per device in the Page Overview. Device Overview The Device Overview offers you a list of all the devices you can control with ProntoPro NG. To view the Device Overview, press the Device Overview button at the top of the touch screen. @@@ You can navigate between the devices in two different ways:  Tap the device you want to operate from the Device Overview.  Tap the Device Left button at the top of the touch screen to navigate to the previous device. Tap the Device Right button at the top of the touch screen to navigate to the next device. By default you navigate through ProntoPro NG, using this touch screen navigation. When cursor navigation is enabled, the Device Left and Device Right button disappear and the Cursor Navigation icon appears. You then navigate through the devices and pages using the cursor. For more information on changing the touch screen navigation to cursor navigation, see “Operating ProntoPro NG with the Cursor” on page 37. Page Overview The Page Overview offers you a list of all the pages for one device. To view the Page Overview, tap the Page Overview button, that displays the page number in the upper area of touch screen. @@@ Device OverviewbuttonPage Overview button Device Right button Device Left button

Getting Started 15 You can navigate between the different pages in two different ways:  Tap the page you want to operate from the Page Overview.  Press the Page Up or Page Down hard button on the left side of ProntoPro NG.

Customizing ProntoPro NG 20 2 Tap in the Tools Menu. The ‘Learn Tool’ screen appears. 3 Tap . The last page you have visited appears. 4 Navigate to the Device and the Page that contains the button you want to learn. 5 Position ProntoPro NG and the remote control as illustrated above. Note Make sure that you aim ProntoPro NG`s learning eye at the remote control’s IR window. The distance between ProntoPro NG and the remote control should be between 4 and 8 inches (10 and 20 cm). 6 Tap the button you want to learn. A Learning indication appears in the top center of the touch screen. 7 Press and hold the key on the other remote control for 1 second. Make sure you press the key within 5 seconds. If learning succeeded, you will get an OK message. If learning failed, you will get a Failure message. See “ProntoPro NG will not learn commands” on page 44 for more information. 8 Select other buttons on ProntoPro NG you want to learn. 9 Press the left firm key labeled below the touch screen to stop learning. Learning a Device Action 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Learn Tool’ screen appears. 3 Tap . The Device Overview appears. 4 Position ProntoPro NG and the remote control as illustrated above. Note Make sure that you aim ProntoPro NG’s learning eye at the remote control’s IR window. The distance between ProntoPro NG and the remote control should be between 4 and 8 inches (10 and 20 cm). 5 Tap the Device for which you want to learn a Device Action. A Learning indication appears in the top center of the touch screen. 6 Press the key on the other remote control. If learning succeeded, you will get an OK message. If learning failed, you will get a Failure message. 7 Select other Devices on the Device Overview you want to learn. 8 Press the left firm key labeled below the touch screen to stop learning. Labeling Elements The Label Tool allows you to label a button, a device or a page. In the Label Tool you can find a virtual keyboard. This keyboard zooms in when you tap a character.

Customizing ProntoPro NG 21 The keyboard contains four different character sets, including a series of symbols you can use for labeling. You use the Shift button to switch between the 5 character sets on the keyboard. For a complete list of the symbols, see “List of Symbols” on page 45. Labeling a Button 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Label Tool’ screen appears. 3 Tap . The page you last visited appears. 4 Navigate to the Device and the Page that contains the button you want to label. 5 Tap the button you want to label. The ‘Labeling’ screen appears. 6 Tap the keyboard. The keyboard zooms in. 7 Tap the character you want to add to the label. The character is added to the label. The keyboard automatically zooms out again. 1 To zoom out without adding a character to the label, tap . The character is not added to the label. The keyboard is zoomed out. 2 To use other characters and symbols, tap . The character set on the keyboard switches. You can choose from four different character sets. 3 To remove characters, press the firm key labeled . The character in front of the cursor is removed. 8 You can add other characters to the label. 9 Tap . The label of the selected button is changed. The last visited page appears again. -or- Tap . The last visited page appears again, without changing the label of the selected button. 10 You can select other buttons on ProntoPro NG to label. 11 Press the left firm key labeled below the touch screen to exit the Label Tool.

Customizing ProntoPro NG 22 Labeling a Device 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Label Tool’ screen appears. 3 Tap . The Device Overview appears. 4 Tap the Device you want to label. The ‘Labeling’ screen appears. 5 Follow the instructions 6 to 8 of “Labeling a Button” on page 21. 6 Tap . The label of the selected Device is changed. The Device Overview appears again. -or- Tap . The Device Overview appears again, without changing the label of the selected device. 7 You can select other Devices in the Device Overview to label. 8 Press the left firm key labeled below the touch screen to exit the Label Tool. Labeling a Page 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Label Tool’ screen appears. 3 Tap in the ‘Label Tool’ screen. The Page Overview appears. 4 Tap the Page you want to label. The ‘Labeling’ screen appears. 5 Follow the instructions 6 to 8 of “Labeling a Button” on page 21. 6 Tap . The label of the selected Page is changed. The Page Overview appears again. -or- Tap . The Page Overview appears again, without changing the label of the selected page. 7 You can select another Page in the Page Overview to label. 8 Press the left firm key labeled below the touch screen to exit the Label Tool.

Customizing ProntoPro NG 24 Note Added devices are automatically positioned at the end of the Device Overview. You can move devices with the Move Tool. See “Moving Devices” on page 24 for more information. Deleting Elements The Delete Tool allows you to delete a button or a device. Deleting a Button 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Delete Tool’ screen appears. 3 Tap . The last visited page on the ProntoPro NG appears. 4 Navigate to the Device and the Page that contains the button you want to delete. 5 Tap the button you want to delete. A message screen appears. 6 Tap . 7 The button is deleted. You can select other buttons on ProntoPro NG to delete. 8 Press the left firm key labeled below the touch screen to exit the Delete Tool. Deleting a Device 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Delete Tool’ screen appears. 3 Tap . The Device Overview appears. 4 Tap the Device you want to delete. A message screen appears. 5 Tap . The Device is deleted. 6 You can select other Devices on ProntoPro NG to delete. 7 Press the left firm key labeled below the touch screen to exit the Delete Tool. Moving Devices The Move Tool allows you to move a device up or down the Device Overview, enabling you to put your most used devices at the top of the list. 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears.

Customizing ProntoPro NG 25 2 Tap in the Tools Menu. The ‘Move Tool’ screen appears. 3 Tap the Device you want to move in the Devices list. 4 Tap the Move Up or Move Down button in the ‘Moving’ screen. The selected Device moves up/down in the Device List. 5 Tap in the ‘Moving’ screen. The Device is moved.

Customizing ProntoPro NG 26 Adjusting the Settings In the Settings Page you can adjust several settings. You can:  Set the time and date as described earlier, on page 11.  Set the timeout of the LCD screen;  Setting the Brightness of the Backlight;  Set the timeout of the LCD backlight;  Set the volume level;  Set the animation mode;  Set the language of the ProntoPro NG,as described earlier, on page 13.  Set ProntoPro NG to operate with the Cursor;  Calibrate the touch screen. @@@ 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Select . The first Settings Page appears. Setting the Timeout of the LCD Screen The timeout of the LCD screen determines how long the LCD touch screen stays active before turning off. Shortening the active time will increase ProntoPro NG’s battery life. Note The LCD screen will only time out when you are not using ProntoPro NG. 1 Tap in the first Settings Page. The LCD Timeout button is selected. The ‘+’ and ‘-’ labels appear on the two middle firm keys below the touch screen. 2 To increase the timeout, press (and hold) the firm key labeled ‘+’. -or- To decrease the timeout, press (and hold) the firm key labeled ‘-’. 3 Tap again. The new LCD screen timeout is set.

Customizing ProntoPro NG 27 Setting the Brightness of the Backlight You can adjust the intensity of the LCD backlight. There are 4 levels of backlight brightness. 1 Tap the button in the first Settings Page. The Brightness button is selected. The ‘+’ and ‘-’ labels appear on the two middle firm keys below the touch screen. 2 To increase the timeout, press (and hold) the firm key labeled ‘+’. -or- To decrease the timeout, press (and hold) the firm key labeled ‘-’. 3 Tap the button again. The new Backlight Brightness is set. Setting the Volume Level You can set the volume level for the hard buttons as well as for the touch screen buttons. The volume of the button refers to the loudness of the beep you hear when you press or tap a button. Setting the Volume Level of the Hard Buttons To adjust the volume of the hard buttons, tap in the first Settings Page. You can either select 1 of the 3 volume levels or choose to mute. Every time you press, the volume level increases with one step up to level 3. Setting the Volume Level of the Touch Screen To adjust the volume level of the touch screen, tap in the first Settings Page. You can either select 1 of the 3 volume levels or choose to mute. Every time you tap, the volume level increases with one step up to level 3. Setting the Navigation for ProntoPro NG The cursor is used by default to operate your devices. You then navigate the ProntoPro NG with the touch screen buttons. However, you can also set the cursor to browse through ProntoPro NG’s devices and pages. For more information on operating the ProntoPro NG with the cursor, see ‘Operating ProntoPro NG with the Cursor’ on page 37. To set the navigation for the ProntoPro NG, tap in the second Settings Page:  You can select Touch Screen Navigation to navigate the ProntoPro NG with the touch screen buttons.  You can select Cursor Navigation to navigate the ProntoPro NG with the cursor. Setting the Animation Mode ProntoPro NG provides navigation feedback through graphical animations. Switching pages is done with a page transition, switching from Use Mode to one of the Tools is accompanied with a mode transition. You can enable and disable the animations of your ProntoPro NG in the second Settings Page:  You can disable the animations by choosing ‘None’ (no animations). By disabling all animations you use the absolute maximum of your ProntoPro NG’s processing speed.  When changing pages with the ‘Page Only’ animation, one page seems to slide out of the screen, while the second page slides in.  The ‘Mode Only’ animation makes a page ‘drop’ out of the top of the touch screen.  With the option ‘Full’ you can enable both animations at the same time.

Customizing ProntoPro NG 28 Calibrating the Touch Screen When you first use your ProntoPro NG, the touch screen is already calibrated. However, if you notice that your ProntoPro NGdoes not send out the commands in accordance with what is indicated on the touch screen, it is advised to recalibrate the touch screen. Attention Never use an actual pen, pencil or other sharp object on the touch screen. Use your finger or a pointy object like a plastic-tipped pen intended for use with touch screens. 1 Tap in the second Settings Page. The ‘Calibration’ screen appears. 2 Tap the upper left corner on the touch screen. 3 Tap the lower right corner on the touch screen. The touch screen is calibrated.

Using the Power Features 30 Note You can assign a macro to most buttons of your ProntoPro NG. Only the hard buttons on the left side of ProntoPro NG (Backlight, Page Up and Page Down) cannot be programmed. To add an action to the action list 1 Tap in the ‘Macro’ screen. The last visited page appears again. 2 Navigate to the Device and the Page that contains the button you want to add to the macro. 3 Tap the button with the action(s) you want to add to the macro. The ‘Macro’ screen appears. The actions of the selected button are added at the bottom of the Action List. 4 You can select other buttons to add to the macro. To add a delay to the action list You can add a delay to the action list e.g. to insert a short pause between turning on a device and sending commands to it, allowing the device to warm up. 1 Tap in the ‘Macro’ screen. The ‘+’ button and ‘-’ button appear on the two middle firm keys below the touch screen. 2 To increase the delay, tap (and hold) the firm key labeled ‘+’. -or- To decrease the delay, tap (and hold) the ‘-’ firm key labeled ‘-’. To add a beep to the action list To determine when the macro execution is finished, it is useful to add a beep as final command in the action list. 1 Select the action in the action list, where you want to add a beep. The action is selected. 2 Tap in the ‘Macro’ screen. A default beep is added to the action list, after the selected action. To test the Macro You do not have to exit the Macro Tool to try out the macro you created or edited. From within the Macro Tool you can test the macro. ProntoPro NG executes all actions as you defined them in the action list.  In the ‘Macro’ screen, press the left firm key labeled . ProntoPro NG executes the actions in the action list. Note Make sure that you keep ProntoPro NG aimed at your Home Theater equipment during the macro execution. To finish the macro  Tap in the ‘Macro’ screen. The macro is created and assigned to the button you selected as a target. -or-  Tap in the ‘Macro’ screen. The Tools Menu appears again without creating the macro.

Using the Power Features 31 Editing a Macro Moving an action in the action list 1 To display the ‘Macro’ screen with the action list assigned to the button, follow the instructions 1 to 5 as described in “Creating a Macro” on page 29. 2 Tap the action in the action list you want to move in the ‘Macro’ screen. The selected action is highlighted. 3 Tap the Move Up button or the Move Down button in the ‘Macro’ screen. The selected action moves up/down in the action list. 4 You can select other actions to move. Deleting an action from the action list 1 To display the ‘Macro’ screen with the action list assigned to the button, follow the instructions 1 to 5 as described in “Creating a Macro” on page 29. 2 Tap the action in the action list you want to delete in the ‘Macro’ screen. The selected action is highlighted. 3 In the ‘Macro’ screen, press the right firm key labeled . The selected action is deleted from the action list. 4 You can select other actions to delete. Activating Timers With the Timer Tool you can define actions to be carried out at predefined times. For instance, you can switch on the lights or program your VCR to record your favourite daily TV-show. Note When a timer is executed, you will hear a double beep and a Timer message appears on screen. If ProntoPro NG is performing another task (sending out IR codes, testing a macro, ...) when a timer is due to be executed, ProntoPro NG first continues performing the current task. 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Timer Tool’ information screen appears. 3 Tap in the ‘Timer Tool’ information screen. The ‘Timer’ screen appears.

Using the Power Features 32 @@@ Page 0/6 4 Tap the check box in front of the timer that you want to activate. The Timer is activated. 5 In the ‘Timer’ screen, tap . The ‘Timer’ screen closes and the Tools Menu appears again. The Timer icon @@ appears next to the time indication. -or- In the ‘Timer’ screen, tap . The Timer screen closes without activating the Timer. Creating and Editing Timers Adding a Timer 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Timer Tool’ information screen appears. 3 Tap . The ‘Timer’ screen appears. 4 In the ‘Timer’ screen, tap to add a new timer to the list. A new timer is added to the Timers list. By default a new timer is labeled Timer and a number. It has no start and stop actions defined. 5 To label the timer, tap , as described in Labeling a Timer on page 33 6 To define the start and stop actions for the timer, tap , as described in Editing a Timer on page 34. 7 In the ‘Timer’ screen, tap . The ‘Timer’ screen closes and the Tools Menu appears again. The Timer icon @@ appears next to the time indication. -or- In the ‘Timer’ screen, tap . The Timer screen closes without activating the Timer. Deleting a Timer 1 Tap the ProntoPro NG icon in the top center of the touch screen.

Using the Power Features 33 The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Timer Tool’ information screen appears. 3 Tap . The ‘Timer’ screen appears. 4 Tap the label of the timer you want to delete. The timer is highlighted. @@@ 5 In the ‘Timer’ screen, tap . A message screen appears. 6 In the message screen, tap Delete. The timer is deleted from the list. 7 In the ‘Timer’ screen, tap . The ‘Timer’ screen closes and the Tools Menu appears again. The Timer icon @@ appears next to the time indication. -or- In the ‘Timer’ screen, tap . The Timer screen closes without activating the Timer. Labeling a Timer The default name for a timer is ‘Timer’ followed by a number, for example Timer 5. 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Timer Tool’ information screen appears. 3 Tap . The ‘Timer’ screen appears. 4 Tap the label of the timer you want to label. The timer is highlighted. 5 In the ‘Timer’ screen, tap . The ‘Labeling’ screen appears. 6 Label the timer as described in Labeling Elements on page 20. 7 In the ‘Labeling’ screen, tap . The ‘Timer’ screen appears again and the timer is relabeled.

Using the Power Features 34 8 In the ‘Timer’ screen, tap . The Tools Menu appears again. Editing a Timer 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘Timer Tool’ information screen appears. 3 Tap . The ‘Timer’ screen appears. 4 Tap the label of the timer you want to edit. The timer is highlighted. 5 In the ‘Timer’ screen, tap . The ‘Editing Timer’ screen appears. @@@ 6 To edit the timer, execute the following steps: 1 Set the Start Date. See Setting the Start Date on page 34 for more information. 2 Set the Start Time. See Setting the Start Time or Stop Time on page 35 for more information. 3 Define the Start Action. See Defining the Start Action or Stop Action on page 35 for more details. 4 Set the Stop Time. See Setting the Start Time or Stop Time on page 35 for more information. 5 Define the Stop Action. See Defining the Start Action or Stop Action on page 35 for more details. 6 Define the Repeat Settings. See Defining the Repeat Settings on page 36 for more information. 7 In the ‘Editing Timer’ screen, tap . The timer settings are defined. The ‘Timer’ screen appears again. 8 In the ‘Timer’ screen, tap . The Tools Menu appears again. Setting the Start Date When you add a new timer the Start Date is the current date by default. The Stop Date is calculated automatically based on the Start Date, the Start Time and the Stop Time. To change the Start Date:

Using the Power Features 35 1 In the ‘Editing Timer’ screen, tap the Day button. The Day button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 2 To increase the value, press (and hold) the firm key labeled ‘+’. -or- To decrease the value, press (and hold) the firm key labeled ‘-’. 3 Tap Day button again. The Month is set. 4 Repeat step 1 to 3 for Month button. The Start Date is set. Setting the Start Time or Stop Time 1 In the ‘Editing Timer’ screen, tap the Start Time button or Stop Time button. The Start Time button or Stop Time button is selected. The labels ‘+’ and ‘-’ appear for the two middle firm keys. 2 To increase the time, press (and hold) the firm key labeled ‘+’. -or- To decrease the time, press (and hold) the firm key labeled ‘-’. 3 Tap the Time button again. The new Start Time or Stop Time is set. Note If the Stop Time lies before the Start Time, the Stop Date automatically jumps to the next day. Defining the Start Action or Stop Action ProntoPro NG uses a similar procedure to define the Action List for the Start Action or the Stop Action of the selected timer as in the Macro Tool. See Creating and Editing Macros on page 29 for more information. Example Some examples of timer actions are: switching on your lights at a specific time or recording your favourite daily TV-show with your VCR. 1 In the ‘Editing Timer’ screen, tap the or button. The ‘Macro’ screen appears. 2 In the ‘Macro’ screen, tap . The last visited page appears again. 3 Navigate to the Device and the Page that contains the button you want to add to the macro. 4 Tap the button you want to add to the action list of the timer. The ‘Macro’ screen appears. The action of the selected button is added at the bottom of the Action List.

Using the Power Features 36 5 In the ‘Macro’ screen, tap . The Start Action or Stop Action is defined. The ‘Editing Timer’ screen appears again. Defining the Repeat Settings If you want the timer to repeat itself on more than one occasion, you can use the repeat settings. 1 Tap the button. The `Repeat Settings` screen appears. @@@ 2 Tap the toggle button. By default `No` is selected. The Repeat button toggles between the three setting:  No: This is the default setting;  Daily;  Weekly. 1 To change the setting to ‘Daily’, tap the button again. Every day of the week is automatically selected. 2 If you want to set an end date for the repeating timer, select the End Date check box. The End Date is enabled. 3 Define the End Date, as described in Setting the Start Date on page 34. The End Date is defined. -or- 1 To change the setting to ‘Weekly’, tap the button again. The currect day is selected. 2 Select or deselect the different days of the week on which the timer has to be executed. 3 If you want to set an end date for the repeating timer, select the End Date check box. The End Date is enabled. 4 Define the End Date, as described in Setting the Start Date on page 34. The End Date is defined. -or-  To change the setting to ‘No’, tap the button again. The timer will not be repeated. 3 In the ‘Repeat Settings’ screen, tap . The ‘Editing Timer’ screen appears again. Feedback about the repeat settings is provided below the button.

Using the Power Features 37 Operating ProntoPro NG with the Cursor The cursor is set by default to operate the devices, e.g. to navigate through an on-screen TV menu. The cursor contains 4 cursor keys: Right, Left, Up and Down. Each cursor key contains an action list. This list depends on the device that is being operated. The cursor can also be used to navigate through devices and pages on ProntoPro NG’s touch screen. When you enable the cursor navigation in the Settings Pages, the touch screen navigation with the Left Device and Right Device buttons at the top area of the touch screen disappears and the cursor navigation icon appears in the top left corner. You use the cursor for navigating, and not for operating your devices, until you disable the cursor navigation again. To set the cursor navigation: 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Select the . The first Settings Page appears. 3 Press the Page Down hard button at the left side of the ProntoPro NG. The second Settings Page appears. 4 Tap in the second Settings Page. 5 The cursor navigation is enabled. The Toggle hard button is activated. 6 Tap the ProntoPro NG icon in the top center of the touch screen to exit the Settings Tool. To use the cursor for navigating the ProntoPro NG: 7 Press the Left and Right buttons of the cursor. ProntoPro NG navigates through the devices. 8 Press the Up and Down buttons of the cursor. ProntoPro NG navigates through the pages. 9 Press the Toggle button to easily switch from navigating on ProntoPro NG to controlling audio/video equipment. The Device Left and Device Right buttons appear in the top area of the touch screen and the cursor is used for controlling audio/video equipment. 10 Press the Toggle hard button again to switch back to cursor navigation. Operating ProntoPro NG with RF By default, ProntoPro NG uses infrared (IR) signals to operate devices. IR signals have an operating distance of approximately 33 ft (10 m). Toggle button Up Left DownRight OK

Using the Power Features 38 However, you can choose to have ProntoPro NG working with radio frequency (RF) signals to operate devices from a distance or from an adjacent room. An RF Extender (not included) is therefore required. The RFX6000 is an RF Extender that can be used in combination with ProntoPro NG. The RF Extender receives RF signals from ProntoPro NG and converts them into IR signals, sent out to the device. Therefore, the RF Extender has to be placed near the device you are operating with the RF Extender’s sending eye pointed towards the device. Selecting RF to Operate your Devices 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘RF IR Tool’ screen appears. 3 Tap . The Device Overview appears. 4 Tap the Device for which you want to select RF. The ‘Select IR or RF’ screen appears. By default IR is selected in the Sending Signals list. The Define RF button is disabled. 5 Choose RF in the Sending Signals list. The Define RF button is enabled. 6 Tap . The ‘RF Settings’ screen appears. RF Extender ProntoPro NG RF signals IR signalsIR signals

Using the Power Features 39 7 Select the RF Channel in the RF Channel list you use for the RF Extender. The RF Channel on the RFX6000 has to be the same as the RF Channel on ProntoPro NG. 8 Select the Extender ID in the Extender ID list you use for the RF Extender. The Extender ID on the RFX6000 has to be the same as the Extender ID on ProntoPro NG. Note You can use several RF Extenders with your ProntoPro NG. For each RF Extender you use for your devices, you need to set the RF Channel and the Extender ID. The RF Channel is identical for all RF Extenders. The Extender ID on the RFX6000 is unique for each RF Extender. 9 Tap in the ‘RF Settings’ screen. The RF settings are saved. 10 Tap in the ‘Select IR or RF’ screen. ProntoPro NG will send out RF signals for the selected device. Note Try to keep ProntoPro NG and the RF Extender away from metal objects, as this will have a negative impact on the range. Selecting IR to Operate your Devices 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Tap in the Tools Menu. The ‘RF IR Tool’ screen appears. 3 Tap . The Device Overview appears. 4 Tap the Device for which you want to select IR. The ‘Select IR or RF’ screen appears. RF is selected in the Sending Signals list. 5 Choose IR in the Sending Signals list. The ‘Define RF’ button is disabled. 6 Tap in the ‘Select IR or RF’ screen. ProntoPro NG will send out IR signals for the selected device.

ProntoProEdit NG 40 ProntoProEdit NG If you want to personalize your ProntoPro NG even more beyond its standard programming features, ProntoProEdit NG is the tool for you to use. ProntoProEdit NG is ProntoPro NG’s companion software that you find on the included CD-ROM. Please check the website to make sure that you have the latest version. You can find more information on http://www.pronto.philips.com. With ProntoProEdit NG you can:  Upload and download new configurations to and from your ProntoPro NG. You do this with the PC cable included with your ProntoPro NG: 1 Plug one end of the cable in the USB port on your computer. 2 Plug the other end of the cable in the USB port on ProntoPro NG.  Add, delete, modify and move control panels, devices and commands anywhere on the touch screen;  Save, duplicate and share configuration files, codes or devices with other ProntoPro NG;  Import new graphics to create new buttons and designs;  Use .PNG graphic files that support transparency. You can now place buttons with a transparent background on top of a background image, let transparent buttons overlap or create transparency effects within buttons. You can use the color in the upper left corner as transparency color or you can select a transparency color from a drop-down list.  Personalize configuration files to optimize the use of your ProntoPro NG;  Copy, Paste and Edit plain IR codes that you can exchange with other ProntoPro NG users;  Preview new configuration files on ProntoProEdit NG Simulator, to check what ProntoPro NG’s interface will look like. @@@

FAQ 41 FAQ Why don’t my buttons work properly? When you find that your ProntoPro NG does not send out the commands in accordance with what is indicated on the touch screen, it is advised to recalibrate the touch screen. Calibration enables ProntoPro NG to place the icons on the touch screen in line with their predefined functions. Attention Never use an actual pen, pencil or other sharp object on the touch screen. Use your finger or a pointy object like a plastic-tipped pen intended for use with touch screens. How do I calibrate the touch screen? 1 Tap the ProntoPro NG icon in the top center of the touch screen. The Tools Menu appears. 2 Select . The first Settings Page appears. 3 Press the Page Down hard button at the left side of the ProntoPro NG. The second Settings Page appears. 4 Tap in the second Settings Page. The ‘Calibration’ screen appears. 5 Tap the upper left corner on the touch screen. 6 Tap the lower right corner on the touch screen. The touch screen is calibrated. 7 Tap the ProntoPro NG icon again to exit the Settings Tool. How do I reset ProntoPro NG? Normally, resetting ProntoPro NG is not necessary. However, if ProntoPro NG’s touch screen freezes or if you notice unusual behaviour, you need to perform a reset to get ProntoPro NG running again. 1 Slide the battery cover off the back of ProntoPro NG. You can find the Reset button in the battery compartment. 2 Use an unfolded paperclip or a sharp pencil to carefully press the Reset button. ProntoPro NG restarts. ProntoPro NG beeps twice to indicate it is ready for use. Reset button

FAQ 42 Note If you reset ProntoPro NG, all personal changes like saved and programmed commands, IR codes, timers and macros are retained. Only the time will be reset to 12.00 am. Why does a device respond to some RF signals and not to others? Not all commands for all devices work properly with RF signals. If a device does not respond properly to RF signals sent out by ProntoPro NG, you have to reconfigure ProntoPro NG to operate the device with IR signals. .

Troubleshooting 44 The sending eye is located at the top of ProntoPro NG.  Insert delays to allow devices to start up properly.  Check for inactive buttons in your macro.  Check if you did not reprogram the buttons. Macros do not store commands, they store buttons. If you reprogram a button, the macro executes the new command assigned to the button. ProntoPro NG will not learn commands  Make sure your ProntoPro NG and the remote control are positioned correctly.  When the sending eye of your existing remote control is not pointed towards the learning eye of the ProntoPro NG, ProntoPro NG might not receive the signals properly. Align the remote controls as correctly as possible.  When the distance between your existing remote control and the ProntoPro NG is too short or too long, ProntoPro NG might not receive the signals properly. Try out several distances between 10 and 20 centimeters (4 and 8 inches) to learn the commands.  Avoid programming ProntoPro NG under bright fluorescent light: it might affect the infrared signals.  Make sure the battery pack in the ProntoPro NG is not empty. The configuration file is corrupted When the configuration file is corrupted, you can use ProntoProEdit NG to download a new configuration file. Taken into account that all your customized commands, devices and macros will be lost and you will have to reprogram your ProntoPro NG. Therefore it is recommended to save the configuration by uploading it to the PC with ProntoProEdit NG. Timers do not work  Check if the timer has been activated (p. 31).  Make sure a Start Action for the timer has been defined properly (p. 35).  Check whether the date and time of your ProntoPro NG are set properly (p. 11). Memory Storage Problems Memory storage problems can be the cause of ProntoPro NG not saving a macro. Storage problems can be caused by a full memory or by a low battery pack. ProntoPro NG error messages If one of the following error messages occurs, please contact your dealer or the Philips customer service:  Invalid CF version or corrupt flash;  Incorrect software version. When your ProntoPro NG does not respond and the screen stays blank: 1 Download the configuration file again. 2 When downloading the configuration file again does not work, download the firmware from http://www.pronto.philips.com. Connection to the PC  Make sure the ProntoPro NG battery pack is sufficiently charged while using ProntoProEdit NG to download or upload.  Do not pull out the USB cable while uploading or downloading a configuration file.

Maintaining ProntoPro NG 45 Maintaining ProntoPro NG Important Notices Take care not to scratch the touch screen Use your finger to tap the touch screen or use plastic-tipped pens intended for use with touch screen. Never use an actual pen, pencil or other sharp object on the touch screen. Protect ProntoPro NG from temperature extremes Keep ProntoPro NG away from heaters and other heat sources. ProntoPro NG is not waterproof ProntoPro NG should not be exposed to rain or moisture. Do not store or use ProntoPro NG in any location that is extremely damp or wet. When you have spilled water on ProntoPro NG, you have to take out the battery pack and let ProntoPro NG dry for 48 hours before you replace the battery pack. The touch screen of ProntoPro NG contains a glass element Do not drop ProntoPro NG or subject it to any strong impact. Cleaning ProntoPro NG  Use a soft, damp cloth to clean ProntoPro NG.  If the touch screen of ProntoPro NG is spoiled, clean it with a soft cloth moistened with a diluted window-cleaning solution.  Do not use a corrosive detergent or an abrasive sponge.  Avoid the use of abundant water.

List of Symbols 46 List of Symbols Pause Stop Normal run; normal speed Normal run; normal speed Fast run; fast speed Fast run; fast speed Slow run; slow speed Slow run; slow speed Eject Recording, general Key Navigate Still mode Tape running direction Next track Previous track Fast forward to index Rewind to index Frame by frame, general Frame by frame, general Subtitle Cancel picture Picture-in-picture mode Menu Picture-in-picture shift Picture-in-picture swap Multi-picture display Picture-in-picture select Teletext mode Page number up Page number down Page enlargement TV and text mixed 1st or 2nd language Last view; previous program Stand-by Zone focus: long distance Zone focus: very short distance Single or multi-digit selection Brightness; brilliance

List of Symbols 47 Contrast Brightness/contrast Color saturation Lamp; lighting; illumination Split screen freeze / double screen freeze Split screen swap / double screen swap Split screen / double screen Movie expand Personal preference Picture-in-picture freeze Main index page Picture freeze Programmable timer; general Enter Application assistance Actual time on screen EPG / Electronic Program Guide Video output Read data from store Write data into store Page hold Sound muting Additional information on screen Spatial sound effect Television; video Sound; audio Surround sound Dolby Digital Digital Theater Systems Active control

Specifications 48 Specifications The specifications and design of this product are subject to change without notice. Display 64k color TFT 3.8” touch screen LCD 320x240 pixels (QVGA) resolution White LED-backlight for LCD and buttons Interface USB 1.1-port connector Software Database with IR codes to operate more than 800 brands Built-in Philips IR codes Total number of devices only limited by memory Infrared (IR) 4 high performance IR-sending LEDs, 1 receiver LED Operating distance of approximately 33 ft (10m) Learning frequency up to 78 KHz and 455 KHz Radio frequency (RF) Band: 418 MHz 16 Extender ID’s and 4 Channels Memory 16 Mbyte (extendable to 32 Mbyte) Power management Power on by tapping the touch screen, by tilting the ProntoPro NG or by pressing a button Power off automatically Dimensions (HxWxD) 6.07 inch x 3.64 inch x 1.10 inch (154,2mm x 92,4mm x 27,8mm) Operating temperature 41°-113° F (5° – 45° C) Accessories Included: USB cable for PC connection CD-ROM with ProntoProEdit NG software AAA rechargeable battery pack (4x1.2 V) Docking station Not included: RF Extender (RFX6000) ProntoProEdit NG PC requirements: Windows 98SE, ME, 2000, XP 64 MB of RAM 75 MB of free hard disk space Free USB Port CD-ROM player IR-database information: Redesigned by UEI Technology Licensed under U.S. Patent 5,689,353 Portions  UEI 1999

Glossary 50 IR code ProntoPro NG sends out infrared (IR) signals to operate devices. IR codes for all kinds of video and audio device brands are stored in ProntoPro NG’s universal database. By selecting IR codes and assigning them to buttons and hard buttons, you can program your ProntoPro NG to operate your equipment. When IR codes are not present in the database, you can always learn them from the conventional remote control of your equipment. Label A label is the text you want to put on a soft button or a firm key. LCD Short for liquid crystal display. LCD backlight LCD backlight is a special light source that is placed behind the LCD screen, enhancing the visibility of this screen. Light sensor The light sensor on your ProntoPro NG causes the backlight to switch on automatically according to the ambient light of your home theater environment. Link A link, also called a button alias, is a shortcut from the action list of one button to the action list of another button. Instead of adding the same actions to several buttons or hard buttons, you can create a link and reuse the action list. When your ProntoPro NG is executing an action list and comes across a link, the action list referred to by that link is executed. Macro A macro is a sequence of actions executed when pressing a single button on ProntoPro NG. Every button or hard button can act as a macro and perform a list of commands. It is the same as an action list. Mode animation When you switch from using the ProntoPro NG to the Tools Menu, the ProntoPro NG icon slides to the top middle of the screen. This is called a ‘mode animation’. Page A page of a device is the area of 320 by 240 pixels on ProntoPro NG's touch screen containing buttons or other objects. Page animation When you switch from one page to another, the first page slides out of the screen and the second page slides in the screen. This is called a ‘page animation’. ProntoPro NG ProntoPro NG is a universal remote control with a touch screen. You can customize and fully configure ProntoPro NG to your personal needs: the devices you want to operate, the functions you want to perform and the layout on ProntoPro NG. ProntoProEdit NG ProntoProEdit is the visual editor for creating and configuring ProntoPro Configuration Files. RF Short for Radio Frequency. RF code You can choose to operate your devices with RF signals instead of IR signals. To use RF signals, you need an RF Extender. The advantage of RF is that it spreads in all directions and that it pervades walls. In other words, you can operate your devices from an adjacent room. RF Extender An RF Extender is a converter box that receives RF signals and turns them into IR signals to operate devices. When your ProntoPro NG sends out RF codes, the RF Extender receives them and sends out IR codes to your devices. RFX6000 The RFX6000 is an RF Extender that can be used in combination with ProntoPro NG. Settings Tool The Settings Tool allow you to consult and adjust several settings, for instance consulting the battery level, setting the date and time, calibrating the touch screen, ... Simulator ProntoPro NG simulator is a separate application in ProntoProEdit NG package, which simulates every aspect of your ProntoPro NG. You use ProntoPro NG simulator to test your PCF without the need to download it to your ProntoPro NG. When you make changes in ProntoPro NG simulator, they will not be saved in the configuration file. Soft button A soft button is a button that can be found on the touch screen. The layout and the visual aspects of a soft button can be changed. You can also configure the functions of the soft buttons. Timer A timer allows you to define actions to be carried out at predefined times. For instance, you can set an alarm or program your VCR to record your favorite daily TV-show. Touch screen The touch screen of your ProntoPro NG is the centered area that contains soft buttons you can use to operate the remote control. USB USB (Universal Serial Bus) is a "plug and play" interface between a computer and add-

51 on devices (such as audio players, joysticks, keyboards, telephones, scanners, and printers).

Copyright 54 Copyright © 2003 Royal Philips Electronics NV All rights are reserved. Reproduction in whole or in part is prohibited without prior consent of the copyright owner.

Navigation menu