Philips Consumer Lifestyle HTL7180 Soundbar Speaker User Manual

Philips Consumer Lifestyle Soundbar Speaker

User manual

www.philips.com/welcomeUser manualAlways there to help youRegister your product and get support atQuestion?Contact Philips
1ENContents1 Important 2Important safety instructions 2Care for your product 3Care of the environment 3Help and support 42 Your SoundBar 5Indicators on the main unit 5Remote control 6Connectors 6Wireless speakers 7Wireless subwoofer 83 Connect and set up 9Charge speakers 9Pair up with speakers/subwoofer 9Place speakers 10Connect to TV 11Connect digital devices through HDMI 11Connect audio from TV and other devices 114 Use your SoundBar 13Adjust the volume 13Choose your sound 13MP3 player 14Play music via Bluetooth 14Auto standby 15Apply factory settings 155 Wall mount your SoundBar 16Wall mount 166 Productspecications 177 Troubleshooting 188 Notice 19Notice of compliance 19
2 3ENEN• If you suspect that a battery has been swallowed or placed inside any part of the body, seek immediate medical attention.• When you change the batteries, always keep all new and used batteries out of reach of children. Ensure that the battery compartment is completely secure after you replace the battery.• If the battery compartment cannot be completely secured, discontinue use of the product. Keep out of reach of children and contact the manufacturer. •Apparatus shall not be exposed to dripping or splashing. •Do not place any sources of danger on the apparatus (forexample.liquidlledobjects, lighted candles). •This apparatus may contain lead and mercury. Dispose according to local, State or Federal laws. For disposal or recycling information, please contact your local authorities. For additional assistance on recycling options, please contact www.mygreenelectronics.com or www.eiae.org or www.recycle.philips.com. •Where the MAINS plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable. •Do not place this apparatus on the furniture that is capable of being tilted by a child and an adult leaning, pulling, standing or climbing on it. A falling apparatus can cause serious injury or even death.• This apparatus should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided. Make sure to leave a space of 7.8 inches (20cm) or more around this apparatus.Class II equipment symbol This symbol indicates that the unit has a double insulation system. This 'bolt of lightning' indicates uninsulated material within your unit may cause an electrical shock. For the safety of everyone in your household, please do not remove product covering. The 'exclamation point' calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems. WARNING:Toreducetheriskofreorelectric shock, this apparatus should not be exposedtorainormoistureandobjectslledwith liquids, such as vases, should not be placed on this apparatus. CAUTION: To prevent electric shock, match wide blade of plug to wide slot, fully insert. Care for your productUseonlymicroberclothtocleantheproduct.Care of the environment Your product is designed and manufactured with high quality materials and components, which can be recycled and reused. Please visit www.recycle.philips.com for additional information on a recycling center in your area. Never dispose of your product with other household waste. Please inform yourself about the local rules on the separate collection of 1 ImportantRead and understand all instructions before you use your product. If damage is caused by failure to follow instructions, the warranty does not apply.Important safety instructions •Read these instructions. •Keep these instructions. •Heed all warnings. •Follow all instructions. •Do not use this apparatus near water. •Clean only with dry cloth. •Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. •Do not install near any heat sources such as radiators, heat registers, stoves, or otherapparatus(includingampliers)thatproduce heat. •Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plugdoesnottintoyouroutlet,consultan electrician for replacement of the obsolete outlet. •Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. •Only use attachments/accessories speciedbythemanufacturer. •Use only with the cart, stand, tripod, bracketortablespeciedbythemanufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. •Unplug this apparatus during lightning storm or when unused for long periods of time. •Refer all servicing toqualiedservicepersonnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. •Battery usage CAUTION - To prevent battery leakage which may result in bodily injury, property damage, or damage to the unit:• Install all batteries correctly, + and - as marked on the unit.• Do not mix batteries (old and new or carbon and alkaline, etc.).• Remove batteries when the unit is not used for a long time.• The batteries shall not be exposed to excessiveheatsuchassunshine,reorthe like.• Perchlorate Material - special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate.• The product/remote control may contain a coin/button type battery, which can be swallowed. Keep the battery out of reach of children at all times! If swallowed, the battery can cause serious injury or death. Severe internal burns can occur within two hours of ingestion.
4 5ENEN2 Your SoundBarCongratulations on your purchase, and welcometoPhilips!Tofullybenetfromthe support that Philips offers, register your SoundBar at www.philips.com/welcome.Indicators on the main unitThis section describes the information of the LED indicators on the main unit. a Volume indicator• When you change volume, one or multiple indicators (up to eight indicators) light up to indicate the volume level.Wireless pairing indicators• During wireless pairing between the main unit and the surround speakers, eight indicators blink one by one.• When the pairing succeeds, eight indicators light up for three seconds.• If the pairing fails, eight indicators blink three times.b HDMI ARC• Lights up when you select HDMI ARC as the input source. • Blinks when no audio from the selected HDMI ARC source is detected, or when an unsupported audio format is detected.acdefghibjc HDMI 1Lights up when you select HDMI IN 1 as the input source.d HDMI 2Lights up when you select HDMI IN 2 as the input source.e OPTICAL/COAX• Lights up when you switch to optical or coaxial input source. • Blinks when an unsupported audio format is detected.f AUXLights up when you switch to AUX input source.g AUDIO-INLights up when you switch to AUDIO-IN source (3.5mm jack).h Bluetooth• Lights up when you switch to Bluetooth mode and Bluetooth devices are paired. • Blinks when you switch to Bluetooth mode and Bluetooth devices are not paired.i V. SURR indicator• Lights up when surround mode is selected. • Off when stereo mode is selected.• Blinks once when night mode/auto volume is enabled.• Blinks twice when Dolby Digital audio is input.• Blinks twice when night mode/auto volume is disabled.• Blinks three times when DTS audio is input.j (Standby-On/Standby indicator)When the SoundBar is in standby, the standby indicator turns red.electrical and electronic products and batteries. The correct disposal of these products helps prevent potentially negative consequences on the environment and human health.The batteries supplied do not contain the heavy metals mercury and cadmium. Nevertheless, in many areas batteries may not be disposed of with your household waste. Please ensure you dispose of batteries according to local regulations.For perchlorate material, special handling may apply. Visit www.dtsc.ca.gov/hazardouswaste/perchlorate.Help and supportPhilips provides extensive online support. Visit our website at www.philips.com/support to:• download the user manual and the quick start guide• watch video tutorials (available only for selected models)• ndanswerstofrequentlyansweredquestions (FAQs)• email us a question• chat with our support representative.Follow the instructions on the website to select your language, and then enter your product model number. Alternatively, you can contact Philips Consumer Care in your country. Before you contact Philips, note down the model number and serialnumberofyourproduct.Youcanndthisinformation on the back or bottom of your product.
6 7ENENRear connectors a AC MAINS~Connect to the power supply.b TO TV-HDMI OUT (ARC)Connect to the HDMI (ARC) input on the TV. c HDMI IN 2Connect to the HDMI output on a digital device.d HDMI IN 1Connect to the HDMI output on a digital device. e DIGITAL IN-OPTICALConnect to an optical audio output on the TV or a digital device. f DIGITAL IN-COAXIALConnect to a coaxial audio output on the TV or a digital device. g AUDIO IN-AUXConnect to an analog audio output on the TV or an analog device. h AUDIO-INAudio input from, for example, an MP3 player (3.5mm jack).bc efghdaWireless speakersThe SoundBar comes with 2 wireless surround speakers (left and right). * The illustration above is for the right speaker's top view and bottom view.a Speaker indicator• During wireless pairing between the main unit and the speaker, the indicator blinks red quickly.• When the pairing succeeds, the indicator turns into solid white (undocked from the main unit), or the indicator lights up white 30 seconds then fades off (being docked into the main unit).• When the pairing fails or pairing remains undone, the indicator blinks red slowly.• When the speaker is being charged (docked into the main unit), the indicator lights up amber.• When the speaker goes to standby, the indicator blinks amber.b Connection keyPress with a pin to enter the pairing mode for the speaker.c POWER ONPress to turn on the wireless speaker if it automatically goes to standby.POWER ONabcRemote controlThis section includes an overview of the remote control. a (Standby-On) • Switch the SoundBar on or to standby.• When EasyLink is enabled, press and hold for at least three seconds to switch all connected HDMI CEC compliant devices to standby.b HDMI selectionHDMI ARC: Switch your source to HDMI ARC connection.HDMI 1: Switch your source to the HDMI IN 1 connection.BluetoothajihgfdcebHDMI 2: Switch your source to the HDMI IN 2 connection.c Source buttonsOPTICAL: Switch your audio source to the optical connection. COAX: Switch your audio source to the coaxial connection. AUDIO-IN: Switch your audio source to the AUDIO-In connection (3.5mm jack).AUX: Switch your audio source to the AUX connection. Bluetooth: Switch to Bluetooth mode.d NIGHT MODE ON/OFFTurn night mode on or off.e Volume control+/-: Increase or decrease volume. : Mute or restore volume.f V.SURR• Toggle between stereo and virtual surround sound.• In HDMI-in mode (connected via HDMI IN 1 or HDMI IN 1), press and hold to switch audio output through the SoundBar speaker or TV speaker. g BASS +/-Increase or decrease bass.h TREBLE +/-Increase or decrease treble.i AUDIO SYNC +/-Increase or decrease audio delay.j AUTO VOLUME ON/OFFTurn auto volume or or off.ConnectorsThis section includes an overview of the connectors available on your SoundBar.
8 9ENEN3 Connect and set upThis section helps you connect your SoundBar to a TV and other devices, and then set it up. For information about the basic connections of your SoundBar and accessories, see the quick start guide. Note •Foridenticationandsupplyratings,seethetypeplateat the back or bottom of the product. •Before you make or change any connections, make sure that all devices are disconnected from the power outlet.Charge speakersIf the wireless surround speaker is undocked from the main unit, its battery level is indicated by the indicator on the speaker.• Light up white: full battery• Light up red: low battery level (less than 30% remaining)• Flash red: near empty (less than 10% remaining) 1 Dock your speakers onto the main unit to charge the speakers.2 Turn on the main unit. » During charging, the indicator on the speaker lights up amber. » When fully charged, the indicator on the speaker lights up white for 30 seconds.Note •It may take around 2 hours to fully charge the speakers. •If the charging lasts more than 4 hours during standby of the main unit, the speakers automatically switch to standby.Pair up with speakers/subwooferThe wireless speakers and subwoofer automatically pair up with the SoundBar for wireless connection when you turn on the SoundBar, the speakers and the subwoofer. If no audio from the wireless speakers and subwoofer can be heard, manually pair up the speakers and the subwoofer.Pair up with the speakers1 Turn on the SoundBar and the surround speaker. » If the connection to the SoundBar is lost, the indicator on the speaker blinks red slowly.2 Press the Connection key on the speaker with a pin to enter the pairing mode. » The indicator on the speaker blinks red quickly.3 On the remote control, press AUX, and then press TREBLE -, BASS + and + (Volume) within three seconds. » If the pairing succeeds, the indicator on the speaker lights up white (undocked from the main unit), or the indicator on the speaker lights up white for 30 seconds (being docked into the main unit).Wireless subwooferThe SoundBar comes with a wireless subwoofer. a CONNECTPress to to enter the pairing mode for the subwoofer.b Subwoofer indicator• When the power is turned on, the indicator lights up.• During wireless pairing between the subwoofer and the main unit, the indicator blinks white quickly.• When the pairing succeeds, the indicator lights up white.• When the pairing fails, the indicator blinks white slowly.c AC MAINS~Connect to the power supply.
10 11ENEN Connect to TVConnect your SoundBar to a TV. You can listen to audio from TV programs through your SoundBar. Use the best quality connection available on your SoundBar and TV.Connect to TV through HDMI (ARC)Your SoundBar supports HDMI with Audio Return Channel (ARC). If your TV is HDMI ARC compliant, you can hear the TV audio through your SoundBar by using a single HDMI cable. 1 Using a High Speed HDMI cable, connect the HDMI OUT (ARC) connector on your SoundBar to the HDMI ARC connector on the TV. • The HDMI ARC connector on the TV might be labeled differently. For details, see the TV user manual.2 On your TV, turn on HDMI-CEC operations. For details, see the TV user manual. TVNote •If your TV is not HDMI ARC compliant, connect an audio cable to hear the TV audio through your SoundBar. (see 'Connect audio from TV and other devices' on page 11) •If your TV has a DVI connector, you can use an HDMI/DVI adapter to connect to TV. However, some of the features may not be available.Connect digital devices through HDMIConnect a digital device such as a set-top box, DVD/Blu-ray player, or games console to your SoundBar through a single HDMI connection. When you connect the devices in this way and playaleorgame,the• video is automatically displayed on your TV, and • audio is automatically played on your SoundBar. 1 Using a High Speed HDMI cable, connect the HDMI OUT connector on your digital device to the HDMI IN 1/2 on your SoundBar.2 Connect your SoundBar to TV through HDMI OUT (ARC). • If the TV is not HDMI CEC compliant, select the correct video input on your TV.3 On the connected device, turn on HDMI-CEC operations. For details, see the user manual of the device.Connect audio from TV and other devicesPlay audio from TV or other devices through your Soundbar speakers.Use the best quality connection available on your TV, Soundbar, and other devices. » If the pairing fails, the indicator on the speaker blinks red slowly.4 If the pairing fails, repeat the steps above.5 Repeat the steps above to pair up the other surround speaker with the main unit.Pair up with the subwoofer1 Turn on the SoundBar and the subwoofer. » If the connection to the SoundBar is lost, the indicator on the subwoofer blinks white slowly.2 Press the CONNECT button on the subwoofer to enter the pairing mode. » The indicator on the subwoofer blinks white quickly.3 On the remote control, press AUX, and then press TREBLE -, BASS + and + (Volume) within three seconds. » If the pairing succeeds, the indicator on the subwoofer lights up white. » If the pairing fails, the indicator on the subwoofer blinks white slowly.4 If the pairing fails, repeat the steps above.Place speakersFor best sound effect, position all the speakers towards the seating position and place them close to your ear level (seated). Note •Surround sound depends on factors such as room shape and size, type of wall and ceiling, windows and reectivesurfaces,andspeakeracoustics.Experimentwiththespeakerpositionstondtheoptimumsettingfor you.Follow these general guidelines for speakers placement.1 Seating position:This is the center of your listening area.2 Place the SoundBar in front of the seating position.3 REAR L (rear left) and REAR R (rear right) surround speakers: Place the rear surround speakers to the left and right side of your seating position, either in line with it or slightly behind it. 4 SUBWOOFER (subwoofer):Place the subwoofer at least one meter to the left or right of the TV. Leave about 10-centimeter clearance from the wall.Dock the surround speakersYou can also dock your surround speakers onto the main unit to listen to audio, for example, watching TV shows and news.SUBWOOFERREAR RREAR L
12 13ENEN4 Use your SoundBarThis section helps you use the SoundBar to play audio from connected devices.Before you start• Make the necessary connections described in the quick start guide and the user manual.• Switch the SoundBar to the correct source for other devices.Adjust the volume1 Press +/- (Volume) to increase or decrease a volume level.• To mute sound, press (Mute).• To restore the sound, press (Mute) again or press +/- (Volume).Volume indicator• When you change volume, one or multiple Volume indicator (up to 8 indicators) on the main unit light up to indicate a volume level. The more indicators light up, the higher the volume level is. • Ifyoudonotpressthevolumekeyforveseconds, the volume indicators light off, and the current source indicator and the sound mode indicator light up.Choose your soundThis section helps you choose the ideal sound for your video or music.045Surround sound modeExperience an immersive audio experience with surround sound modes.1 Press V.SURR to select a surround mode.• Surround: Creates a surround listening experience. The V.SURR indicator on the main unit lights up.• Stereo: Two-channel stereo sound. Ideal for listening to music.EqualizerChange the high frequency (treble) and low frequency (bass) settings of the SoundBar.1 Press TREBLE +/- or BASS +/- to change the frequency.Treble/bass indicator• When you change frequency levels, one or multiple indicator (up to 8 indicators) on the main unit light up to indicate a frequency level. The more indicators light up, the more the treble or bass is. Auto volumeTurn the auto volume on to keep the volume constant when you switch to a different source. It also compresses the sound dynamics, increasing the volume for quiet scenes and decreasing the volume for loud scenes. 1 Press AUTO VOLUME ON/OFF to turn auto volume on or off. » When auto volume is turned on, the V.SURR indicator blinks once. » When auto volume is turned off, the V.SURR indicator blinks twice.-4 4Note •When your Soundbar and TV are connected through HDMI ARC, an audio connection is not required.Option 1: Connect audio through a digital optical cableBest quality audio 1 Using an optical cable, connect the OPTICAL connector on your SoundBar to the OPTICAL OUT connector on the TV or other device. • The digital optical connector might be labeled SPDIF or SPDIF OUT. Option 2: Connect audio through a digital coaxial cableGood quality audio 1 Using a coaxial cable, connect the COAXIAL connector on your SoundBar to the COAXIAL/DIGITAL OUT connector on the TV or other device. • The digital coaxial connector might be labeled DIGITAL AUDIO OUT. TVOption 3: Connect audio through analog audio cablesBasic quality audio1 Using an analog cable, connect the AUX connectors on your SoundBar to the AUDIO OUT connectors on the TV or other device. DVD
14 15ENEN• When your switch back to Bluetooth mode, Bluetooth connection remains active.Note •The music streaming may be interrupted by obstacles between the device and SoundBar, such as wall, metallic casing that covers the device, or other devices nearby that operate in the same frequency. •If you want to connect your SoundBar with another Bluetooth device, disable the currently connected Bluetooth device. •Philips does not guarantee 100% compatibility with all Bluetooth devices.Auto standbyWhen playing media from a connected device, the SoundBar automatically switches to standby if:• no source button is pressed for 30 minutes, and• no audio/video playback is detected from a connected device.Apply factory settingsYou can reset your SoundBar to the default settings programmed at the factory.1 In AUX mode, press and hold NIGHT MODE OFF for 5 seconds. » When the factory settings restore is complete, the SoundBar automatically switches off and restarts.Synchronize picture and soundIf the audio and video are not synchronized, delay the audio to match the video.1 Press AUDIO SYNC +/- to synchronize the audio with the video.• AUDIO SYNC + increases the sound delay, and AUDIO SYNC - decreases the sound delay. » When you change the value of sound delay, the more value/delay you set, the more indicators on the main unit light up.Night modeFor quiet listening, decrease the volume of loud sounds when audio is played. Night mode is only available for Dolby Digital soundtracks. 1 Press NIGHT MODE ON/OFF to turn night mode on or off. » When night mode is turned on, the V.SURR indicator blinks once. » When night mode is turned off, the V.SURR indicator blinks twice.Note •If auto volume is set to turned on, you cannot enable the night mode.MP3 playerConnect your MP3 player to play your audio lesormusic.What you need• An MP3 player.• A 3.5mm stereo audio cable.1 Using the 3.5mm stereo audio cable, connect the MP3 player to the AUDIO-IN connector on your SoundBar.2 Press AUDIO-IN.3 Press the buttons on the MP3 player to selectandplayaudiolesormusic.• On the MP3 player, it is recommended to set the volume in the range of 80% maximum volume.Play music via BluetoothThrough Bluetooth, connect the SoundBar with your Bluetooth device (such as an iPad, iPhone, iPod touch, Android phone, or laptop), and then youcanlistentotheaudiolesstoredonthedevice through your SoundBar speakers.What you need• A Bluetooth device which supports BluetoothproleA2DP,andwithBluetoothversion as 2.1 + EDR.• The operational range between the SoundBar and a Bluetooth device is approximately 10 meters (30 feet).1 Press Bluetooth on the remote control to switch the SoundBar to Bluetooth mode. » The Bluetooth indicator blinks.2 On the Bluetooth device, switch on Bluetooth, search for and select Philips HTL9100 to start connection (see the user manual of the Bluetooth device on how to enable Bluetooth). » During connection, the indicator blinks.3 Wait until you hear a beep sound from the SoundBar. » The Bluetooth indicator lights up. » If the connection fails, the Bluetooth indicator blinks continually.4 Selectandplayaudiolesormusiconyour Bluetooth device.• During play, if a call is coming, music play is paused. Play resumes when the call ends.• If music streaming is interrupted, place the Bluetooth device closer to the Soundbar.5 To exit Bluetooth, select other source.
16 17ENEN6 Product specificationsNote •Specicationsanddesignaresubjecttochangewithoutnotice.Amplier• FTC total output power: 42W• Woofer L + Woofer R: 32W ( 1% THD, 3ohm, 180Hz-6KHz )• Tweeter L + Tweeter R: 10W ( 1% THD, 12ohm, 7KHz-20KHz)• Subwoofer: • Total output power: • 210W RMS (+/- 0.5 dB, 30% THD) • 168W RMS (+/- 0.5 dB, 10% THD)• Frequency response: 20 Hz-20 kHz / ±3 dB• Signal-to-noise ratio: > 65 dB (CCIR) / (A-weighted)• Input sensitivity:• AUX: 400 mV• AUDIO-IN: 200 mVAudio• S/PDIF Digital audio input:• Coaxial: IEC 60958-3• Optical: TOSLINKBluetooth •Bluetoothproles:A2DP •Bluetooth version: 2.1 + EDRMain unit •Power supply: 120 V~, 60 Hz •Power consumption: 50 W •Standbypowerconsumption:≤0.5W• Speaker impedance: • Woofer: 8 ohm• tweeter: 8 ohm• Speaker drivers: 2 x 63.5 mm (2.5") woofer + 2 x 25.4 mm (1") tweeter •Dimensions (WxHxD): 1035 x 73 x 156 mm (with 2 surround speakers attached) •Weight: 3.9 kgSurround speakers• Speaker impedance: 8 ohm• Speaker drivers: 2 x 63.5 mm (2.5") full range• Dimensions (WxHxD): 191 x 73 x 156 mm• Weight: 0.7 kg/eachSubwoofer• Power supply: 120 V~, 60 Hz• Power consumption: 30 W• Standbypowerconsumption:≤0.5W• Impedance: 4 ohm• Speaker drivers: 1 x 165 mm (6.5") woofer• Dimensions (WxHxD): 200 x 510 x 201 mm• Weight: 4.9 kgWall mount •Dimensions (WxHxD): 40 x 100 x 26.5 mm •Weight: 0.1 kg/eachRemote control batteries• 2 x AAA-R03-1.5 V 5 Wall mount your SoundBarBefore you mount your SoundBar on the wall, read all safety precautions.Wall mountNote •You must detach the surround speakers from the main unit before wall mounting or un-mounting. •Koninklijke Philips Electronics N.V. bears no responsibility for improper wall mounting that results in accident, injury or damage. If you have any query, contact Philips Consumer Care in your country. •Secure the wall mount to a wall that can support the combined weight of the product and the wall mount. •Before wall mount, you need not remove the four rubber feet at the bottom of the soundbar, otherwise therubberfeetcannotbexedback.Screw length/diameterDepend on the type of wall mounting this wall mount bracket, make sure that you use screws of a suitable length and diameter. For information about how to wall your SoundBar, see the wall mount guide.> 25mm3 - 3.5mm
18 19ENEN8 NoticeThis section contains the legal and trademark notices.Notice of complianceThis set complies with the FCC rules, Part 15 and with 21 CFR 1040.10. Operation is subject to the following two conditions:a This device may not cause harmful interference, andb This device must accept any interference received, including interference that may cause undesired operation.FCC rulesThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:• Relocate the receiving antenna.• Increase the separation between equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Radiation Exposure Statement:This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.Warning:Changesormodicationsmadetothis equipment not expressly approved by Philips may void the FCC authorization to operate this equipment.Model number: PHILIPS HTL7180/F7Trade Name: PhilipsResponsible Party:P&F USA, Inc. PO Box 2248 Alpharetta, GA 30023-2248; 1-866-310-0744Canada: This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following Two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This Class B digital apparatus complies with Canadian ICES-003. 7 TroubleshootingWarning •Risk of electric shock. Never remove the casing of the product.To keep the warranty valid, never try to repair the product yourself. If you have problems using this product, check the following points before you request service. If you still have a problem, get support at www.philips.com/support. Main unitThe buttons on the SoundBar do not work.• Disconnect the SoundBar from the power supply for a few minutes, then reconnect.SoundNo sound from SoundBar speakers.• Connect the audio cable from your SoundBar to your TV or other devices. However, you do not need a separate audio connection when:• the SoundBar and TV are connected through HDMI ARC connection, or• a device is connected to the HDMI IN connector on your SoundBar.• Reset your SoundBar to its factory settings.• On the remote control, select the correct audio input.• Make sure that the SoundBar is not muted. No sound from the wireless surround speakers.• Wirelessly connect the speakers to the main unit (see 'Pair up with the speakers' on page 9).• Dock the wireless surround speakers into the main unit to charge the battery.No sound from the wireless subwoofer.• Wirelessly connect the subwoofer to the main unit (see 'Pair up with the subwoofer' on page 10).Distorted sound or echo.• If you play audio from the TV through the SoundBar, make sure that the TV is muted.Audio and video are not synchronized.• Press AUDIO SYNC +/- to synchronize the audio with the video.BluetoothA device cannot connect with the SoundBar.• The device does not support the compatibleprolesrequiredfortheSoundBar.• You have not enabled the Bluetooth function of the device. See the user manual of the device on how to enable the function.• The device is not correctly connected. Connect the device correctly.• The SoundBar is already connected with another Bluetooth device. Disconnect the connected device, then try again.Quality of audio play from a connected Bluetooth device is poor.• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.The connected Bluetooth device connects and disconnects constantly.• The Bluetooth reception is poor. Move the device closer to the SoundBar, or remove any obstacle between the device and the SoundBar.• Turn off Wi-Fi function on the Bluetooth device to avoid interference.• For some Bluetooth, the Bluetooth connection can be deactivated automatically to save power. This does not indicate any malfunction of the SoundBar.
This device complies with Industry Canada RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio RSS-210. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. The device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS-102 RF exposure, users can obtain Canadian information on RF exposure and compliance. Le dispositif rencontre l'exemption des limites courantes d'évaluation dans la section 2.5 de RSS 102 et la conformité à l'exposition de RSS-102 rf, utilisateurs peut obtenir l'information canadienne sur l'exposition et la conformité de rf. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. Cet émetteur ne doit pas être Co-placé ou ne fonctionnant en même temps qu'aucune autre antenne ou émetteur. Cet équipement devrait être installé et actionné avec une distance minimum de 20 centimètres entre le radiateur et votre corps.
Specifications are subject to change without notice© 2013 Koninklijke Philips Electronics N.V.All rights reserved.Document order number: 000000000000

Navigation menu