Pentair Aquatic Systems MOBILETOUCH2A Mobi2 User Manual MobileTouch Manual Rev A 072408

Pentair Aquatic Systems Mobi2 MobileTouch Manual Rev A 072408

Users Manual

MobileTouch Wireless Controller User’s and Installation GuideUser’s and Installation GuideIntelliTouch® Pool & SpaControl SystemMobileTouch® Wireless Controllerpool/spa control system
MobileTouch Wireless Controller User’s and Installation GuideMobileTouch Wireless Controller kit contentsThe following items are included in the MobileTouch Controller kit. If any itemsare missing please contact Technical Support.• MobileTouch wireless controller• AC/DC power adapter• Cradle• User’s and Installation Guide (this manual)© 2008 Pentair Water Pool and Spa, Inc. All rights reserved.1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-800010951 West Los Angeles Ave., Moorpark, CA 93021 • (800) 553-5000MobileTouch®, IntelliTouch® and Pentair Water Pool and Spa® are trademarks and/or registered trademarks of Pentair WaterPool and Spa, Inc. and/or its affiliated companies in the United States and/or other countries. Unless noted, names and brandsof others that may be used in this document are not used to indicate an affiliation or endorsement between the proprietors ofthese names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or registeredtrademarks of those parties or others.iCAUTION: IMPORTANT BATTERY INFORMATION• Danger of explosion if battery is incorrectly replaced.• Replace battery with the same type recommended by Pentair. Use PentairBattery Replacement Kit (P/N 520815Z).•Rechargeable Lithium-ion battery disposal: Unwanted lithium ionbattery pack may be returned to your local recycling center or themanufacturer for disposal.• Dispose of used batteries according to the manufacturer’s instructions.• Dismantling or opening the device (with the exception of the battery door)or case will void warranty and may possibly cause electric shock. FCC Regulatory Safety Notice - This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energy and, if not installed and used in accordancewith the instructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. If this equipment doescause harmful interference to radio or television reception, whichcan be determined by turning the equipment off and on, the user is encouraged to try to correct theinterference by one or more of the following measures:• Reorient or relocate the receiving antenna.• Increase the separation between the equipment and receiver.• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.• Modifications not expressly approved by the party responsible for FCC compliance could void the user’s authority to operate the equipment.Related manuals - Download the IntelliTouch User’s Guide (P/N 520102) at:http://www.pentairpool.com/owners_manuals/controlsIntelliTouch_Pool_Spa_Cntrls_Instll_Guide.pdfTechnical SupportSanford, North Carolina (8 A.M. to 5 P.M. ET)Moorpark, California (8 A.M. to 5 P.M. PT)Phone: (800) 831-7133 - Fax: (800) 284-4151 IC Regulatory NoticeOperation is subject to the following two conditions: (1) this device may not cause interference, and(2) this device must accept any interference, including interference that may cause undesiredoperation of the device.P/N 520886 - Rev A - 07/24/2008 RF Exposure Requirements: This Device must not be co-located or operated in conjunction with any other antenna or transmitter.
MobileTouch Wireless Controller User’s and Installation GuideContentsCharging the MobileTouch Wireless Controller ....................................... 2Setting up the MobileTouch Wireless Controller ..................................... 4MobileTouch Transceiver Antenna Location ........................................... 7Installing the MobileTouch Transceiver .................................................. 8Optional Serial COM Port Expansion Board ........................................ 13MobileTouch Wireless ControllerThe MobileTouch wireless controller provides the same functionality asthe IntelliTouch Indoor Control Panel. It has an operating range of up to500 ft. from the MobileTouch antenna (Transceiver), which is typicallylocated near the IntelliTouch load center. The optimum wirelesstransmit and receive range may be affected by physical obstructions,(especially those containing metal), and geographical features.The MobileTouch controller LCD (liquid crystal display) can besensitive to sunlight. When exposed for extended periods, the LCDscreen will heat up and turn black. If this happens, place the remote ina shaded area and allow the screen to cool down. Do not attempt toadjust the contrast or the screen will be unreadable when it eventuallycools. When used outside, keep the remote covered or in a shadedarea. Prolonged exposure to sunlight may permanently damage theunit. WARNING! Do not plug in the AC adapter to a power sourcewithin five (5) feet of the pool and spa. Canadian installations require aminimum of (3) meters from pool water. Do not recharge outdoors.Only use Pentair approved AC adapter transformer.The MobileTouch wireless controller is water resistant and can beexposed to temporary splashing or wet hands. However, the controlleris not intended to be submersed. Remove unit immediately if it isdropped in the water or exposed to rain. Store the unit indoors in a dryenvironment. Be sure the gold charging contacts are dry beforecharging.MobileTouch Wireless Controller (Previous Model)The previous model of the MobileTouch wireless controller andTransceiver antenna cannot be used with the latest model of theMobileTouch wireless controller and Transceiver antenna. Both modelscannot coexist in the same IntelliTouch system.1
MobileTouch Wireless Controller User’s and Installation Guide2Charging the MobileTouch Wireless ControllerWhen you are not using the MobileTouch controller, place it in thecradle to recharge the battery. This allows the battery to be fullycharged at all times.To charge the MobileTouch controller battery• Plug the AC adapter into an AC wall outlet.• Insert the AC Adapter plug into the bottom of the cradle.• Place the MobileTouch controller in the cradle.Note: When the MobileTouch controller is placed in the cradle thedisplay and backlight will be on. After five minutes the backlightwill shut off. The MobileTouch unit and display are always onwhen seated in the cradle. To turn the backlight on, press anybutton.To use the MobileTouch wireless controller1. Remove the MobileTouch wireless controller from thecradle. Note: With AC power connected to the cradle, theMobileTouch controller can be used while seated in thecradle.2. Press the Power On/Off button (front lower right-side) toswitch the unit on. The main screen is displayed. The LCDbacklight will turn off in five minutes if not in use. Thebattery icon displays three solid bars, only when it’s fullycharged. Note: If the MobileTouch is not being used forextended periods of time, press the Power On/Off switchto turn the controller Off.2MobileTouch controller seated in cradleCradle Power On/Off button
MobileTouch Wireless Controller User’s and Installation GuideMain Screen Check Battery IconThe check battery icon is located in the lower right corner of the mainscreen. If the battery icon displays one or no bars or the screen isblank, this may indicate that the battery cannot power the device andneeds recharging.A complete battery charge takes about 3 to 4 hours. During batteryrecharge, the battery icon bars scroll from right to left. After acomplete battery recharge, the battery icon is replaced with a powerplug icon, indicating the battery is fully charged and is now operatingon AC power from the cradle. Note: If the battery requiresreplacement, only use Pentair replacement battery (P/N 520815Z).Battery IconSufficient charge left in thebatteries to operate device.Three solid bars indicateample battery charge.During battery recharge,bars scroll right to left.Batteries will deplete soon.The power plug icon displays when the batteryis fully charged and the MobileTouch controlleris operating on AC power supplied from cradlePower Plug Icon3
MobileTouch Wireless Controller User’s and Installation Guide4Setting up the MobileTouch Wireless ControllerThe following describes how to assign the MobileTouch wirelesscontroller a communication address for the first time and to add aMobileTouch controller to a system with a controller already installed.After connecting the Transceiver cable to the IntelliTouch load center(see page 8), the system is ready to setup MobileTouch controller.To manually setup the MobileTouch controller:1. On the IntelliTouch Outdoor Control Panel, press the Resetbutton (see below).2. First Time MobileTouch install: The three red SystemControl LEDs will be lit (solid). Wait a few seconds thenpress the “F” Filter button. For IntellliTouch model i10+3,press the “P” Pool Filter Pump button.Add a MobileTouch with existing MobileTouch installed:The three red System Control LEDs will be lit (solid). Waita few seconds then press the “V” button or “1” button.3. The three red System Control LEDs and the auxiliarybutton LEDs will begin cycling. Wait until the LEDs stopcycling. The three System Control LEDs will start to blinkon and off. The IntelliTouch system is ready to assign anaddress for the MobileTouch wireless controller; continuewith Step 4 on page 5.IntelliTouch Outdoor Control Panel Three SystemControl LEDs Auxiliary LEDsResetbuttonF button(i5+3, i5S+3 i7+3,i9+3S, i9+3D)P button (i10+3D)Note: Press V or 1 button to add aMobileTouch controller with existingMobileTouch controller(s) already installed.
MobileTouch Wireless Controller User’s and Installation Guide5MENU SETUP ADVANCEDGetting ThereSetting up the MobileTouch Wireless Controller (continued)Go to the Advanced screen.4. From the MobileTouch Advanced screen, press the lowerbuttons 2 and 4 at the same time. The Service Personnelscreen is displayed.5. Press the button next to LOCK ON ADDRESS to accessthe next screen.Press button 2 and 4 at the same time toaccess the Service Personnel screen
MobileTouch Wireless Controller User’s and Installation Guide6. Press the button next to LOCK ON ADDRESS to assign aunique frequency for the MobileTouch controller to avoidinterference from other wireless devices within range of theMobileTouch transceiver.7. After selecting “Lock On Address” the MobileTouchcontroller is now ready to operate the IntelliTouch system.The “Service Personnel” screen will be displayed.8. Press Exit to return to the main screen or proceed withStep 9 if you are adding another MobileTouch controllerwhile the IntelliTouch outdoor control panel LEDs areflashing.9. To add another MobileTouch controller at this time,repeat Steps 4 (page 5) through 8 for each controller, if not,continue with Step 10.10. Return to the Load Center or Power Center. The SystemControl LEDs will be flashing. Press the Reset button.When the “Auto” LED is illuminated the process is completeand the system is ready for operation.6
MobileTouch Wireless Controller User’s and Installation Guide7MobileTouch Transceiver Antenna LocationThe Transceiver optimum wireless transmit and receive range may beaffected by physical obstructions, (especially those containing metal),weather conditions, and geographical features.The MobileTouch controller has an operating range of up to 500 ft.(line-of-sight) from the MobileTouch Transceiver. The Transceiver kitincludes a 10 ft. connection cable. If needed, using extra cable, thecable length can be lengthened to 300 ft. The recommended locationsfor the Transceiver are shown below.Recommended locations for Transceiver AntennaLOADCENTERNote: Only one MobileTouch controller Transceiver can beused per IntelliTouch system.PossibleantennalocationPossibleantennalocationPossibleantennalocation
MobileTouch Wireless Controller User’s and Installation GuideInstalling the MobileTouch TransceiverThe MobileTouch controller has an operating range of up to 500 ft.(line-of-sight) from the MobileTouch Transceiver. The Transceiver kitincludes a 10 ft. connection cable. If needed, using extra cable, thecable length can be lengthened to 300 ft. The recommended locationsfor the Transceiver are shown on page 7.To install the Transceiver:1. Choose an installation location for the Transceiver near theIntelliTouch load center.2. Remove the two lower retaining screws from theTransceiver and slide the Transceiver case up to remove itfrom the back plate.3. Remove the Transceiver circuit board from the back plate bycarefully lifting it up out of the back plate supports. Place thecircuit board on a clean dry surface away from directsunlight.4. Mount the Transceiver back plate (see page 9) onto a flatwooden surface, such as a wooden fence, or post. Whileholding the back plate, install two lower mounting screwsthrough the back plate lower mounting holes. Tighten thescrews to secure the back plate in place. Install two screwsthrough the upper mounting holes.5. Slide the Transceiver circuit board into the back plate into theboard side supports.6. Route the Transceiver cable up through the bottom of theback plate (see page 9) to the screw terminal connector.7. Insert the four wires into the screw terminals of theTransceiver connector. Using a small flat-blade screwdriver,secure the wires with the screws. Make sure to match thecolor coding of the four wires (see page 12 for wiringdiagram).8. Carefully slide the case over the Transceiver antenna andsecure it to the back plate with the two lower retainingscrews.9. Proceed with “Connecting the Transceiver cable to theIntelliTouch Personality board” on page 10.8
MobileTouch Wireless Controller User’s and Installation GuideScrew terminalsTransceiver circuit boardBack plateRetaining screwsCaseLower exit hole (left side)AntennaUpper mounting point(screw)Transceiver Module91DNGKLB2TD-NRG3TD+LEY4V51DERLower mountingpoint (screw)Lower mountingpoint (screw)Upper mounting point(screw)Left-side Transceivercircuit board support
MobileTouch Wireless Controller User’s and Installation GuideWARNING Switch OFF the main system power to the Load Centerbefore making any connections.1. Unlatch the two enclosure door spring latches, and open thedoor.2. Remove the two retaining screws securing the high voltagecover-panel, and remove it from the enclosure.3. Loosen the two access screws securing the control panel.10Panel retainingscrew(Cover-panelnot shown)AccessscrewRetainingscrewAccessscrewControl panelConnecting the Transceiver cable to the Personality boardLoad Center4. Lower down the hinged control panel to access thePersonality board.
MobileTouch Wireless Controller User’s and Installation Guide5. Route the transceiver cable into the lower plastic grommet,up through the low voltage raceway to the Personality board.6. Insert the four wires into the screw terminals of the COMPORT plug located on the Personality board as shown below.Using a small flat-blade screwdriver, secure the wires withthe screws. Make sure to match the color coding of the fourwires:Pin 4 - Red = +15Pin 3 - Yellow = +DTPin 2 - Green = -DTPin 1 - Black = GND11BLKGRNYELRED IntelliTouch Personalityboard COM PORTS(J7/J8) screw terminalconnector RacewayControl panelPersonalityboardNote: If there no available COM portterminals for the Transceiver cableplug connector to plug in to, theoptional Serial COM Port ExpansionBoard (P/N520818) can be used (seepage 13). Multiple wires may also beinserted into a single screw terminal.
MobileTouch Wireless Controller User’s and Installation Guide7. After the connection has been completed, close the controlpanel into its original position and secure it with the twoaccess screws.8. Close the IntelliTouch front panel and secure it with the tworetaining screws.9. Close the IntelliTouch Load Center front door. Fasten thetwo spring latches.10. Switch the power on to the IntelliTouch Load Center.11. Proceed to “Setting up MobileTouch and IntelliTouch”on page 4.12Personality board COM PORT Pin configurationMobileTouchoutdoor wirelesstransceiver locatedwithin 10 feet fromIntelliTouch LoadCenterCOM PORT screwterminal connector1DNGKLB2TD-NRG3TD+LEY4V51DER
MobileTouch Wireless Controller User’s and Installation Guide13Optional Serial COM Port Expansion Board(for use with IntelliTouch® control systems)If there is not an available COM port for the Transceiver cable plug onthe IntelliTouch Personality board, the optional Serial COM portExpansion Board (P/N 520818) can be used for additional COM portsconnections.Mounting the Expansion Board1. Remove the inside terminal connectors (with wires attached)from the Expansion board and connect it to a COM port onthe Personality board.Note: If this a new Load Center installation, you’ll haveto remove one of the existing (empty) terminal connectorsfrom the Personality board to allow for the Expansionboard terminal connector. You can place the (empty)connector onto the available COM port on theExpansion board.2. Mount the Expansion board on to the back wall in the lowvoltage compartment of the IntelliTouch load center using thefour adhesive backed supports.3. Proceed to “Connecting the Transceiver cable plug to theSerial COM Port Expansion Board,” on page 14.Remove this terminal connectorand connect it to an available COMport on the IntelliTouch Personalityboard.Personality Board
MobileTouch Wireless Controller User’s and Installation Guide14Connecting the Transceiver cable plug to the Serial ComPort Expansion BoardConnect the Transceiver cable plug onto one of the available SerialCOM port expansion board connector terminals.Note: If you have existing accessories (IntelliChlor, IntelliFlo)connected to the IntelliTouch Personality board and need to freeup connectors for additional equipment, remove one of the existingconnectors (with the attached wires to equipment) from thePersonality board and plug it into an available connector on theExpansion board COM port (as shown below).Cables toaccessories(IntelliChlor,Indoor ControlPanel etc.)Low voltagecompartmentExpansionboardadhesivebackedsupports (x4)Connect existingaccessory connectorswires hereConnect to COM port onIntelliTouch PersonalityboardConnector from the Expansion boardConnect IntelliFlowires to two-pinterminal connector
MobileTouch Wireless Controller User’s and Installation Guide15 Notes
MobileTouch Wireless Controller User’s and Installation Guide Notes16
MobileTouch Wireless Controller User’s and Installation Guide Notes17
MobileTouch Wireless Controller User’s and Installation Guide*520886*P/N 520886 - Rev A

Navigation menu