Passtime USA DDD1RX Dock device User Manual

Passtime USA Dock device

User manual

INSTALLATION DIAGRAMPage 1© 2017 Distracted Driving Device, LLC.No party may republish, copy, redistribute, sell or offer for sale to any third party this material or any part of it without express written permission of the authors.If you are making the connecons directly at the baery, you MUST use a 3A size inline fuse (as shown). This is a safety precauon in the case of a nicked or pinched wire contacng metal.POTENTIAL INSTALLATION LOCATIONSThe Comm Device (PTE-5) should be installed as high in the dash as possible to ensure the best performance and to help prevent tampering.• Above or behind instrument cluster• Above any accessible air vents• Above or behind the radioNote: When mounng the device, the LED’s must be facing up and the device should not be obstructed by metal.WIRING DIAGRAMThe Distracted Driving Device (DDD) system is comprised of two separate devices, the DDD Communication Device (PTE-5) and the DDD Handset Dock (DDD-1). Both devices will need to be installed in the vehicle as shown in this document.StarterOBDIIPurple (Starter Out)Starter Control CircuitRed (12v Constant)(Cut)Black (Ground)Blue (Starter In)Pink (Ignition)hot while engine crankingKeyFusePin16Pin 4Comm Device (PTE-5) Dock (DDD-1)STEP 1: INSTALL COMM DEVICE
GROUND - Aach to a secured bare metal chassis ground locaon such as to a new or exisng threaded fastener, or to a grounded circuit such as Pin 4 of the OBDII connector (as shown).12v CONSTANT - Any 12v constant source, that is not being monitored by the computer for voltage draw, can be used, like Pin 16 of the OBDII connector (as shown). Use inline fuse if going direct to the baery.DEVICE HARNESS ELECTRICAL CONNECTIONSPage 2© 2017 Distracted Driving Device, LLC.No party may republish, copy, redistribute, sell or offer for sale to any third party this material or any part of it without express written permission of the authors.IGNITION WIRE- a wire with 12V in “key on” and “crank” posions.STARTER WIRE - the wire with 12V in “crank” posion only. Once the starter wire is cut, connect Harness blue wire to key side of starter. Connect Harness purple wire to solenoid side.STARTER WIREIGNITION WIRENOTE: For all connections, soldering is recommended. Posi-tap and butt connectors are also acceptable (as shown). NOTE: In late model vehicles, starter and ignition connections should be made under hood, near main fuse relay. If harness wires are not long enough, use 3-in-1 wire or equivalent to extend harness (as shown). NOTE: When making these connecons, use grommets if wires must penetrate the firewall and use adequate looming if placing wires in the engine compartment to protect from hot metal surfaces and corrosive liquids.
Page 3© 2017 Distracted Driving Device, LLC.No party may republish, copy, redistribute, sell or offer for sale to any third party this material or any part of it without express written permission of the authors.Install Dock in glove compartment (as shown). Make small hole near Dock locaon for Ground & 12V Constant wires to pass through. Zip-e wires underneath glove compartment to secure Dock and prevent removal from mounted locaon.STEP 2: INSTALL DOCKDock Ground Wire- Bare metal or a common ground connecon is recommended on the passenger side of vehicle (as shown).Dock 12V Constant Wire- Connect Dock 12V Constant to inline fuse (size 3A). Then connect inline fuse to Harness 12V Constant connecon as made previously at OBDII connector.Note: Please ensure Dock locaon and placement will allow unrestricted access by the user to insert their handset into the Dock and easily secure it using the rubber strap.
Page 4© 2017 Distracted Driving Device, LLC.No party may republish, copy, redistribute, sell or offer for sale to any third party this material or any part of it without express written permission of the authors.STEP 3: ACCOUNT SETUPNeed Help? Visit: DistractedDrivingDevice.com or Call 1-800-579-9077Use of the Distracted Driving Device requires the installaon of the Distracted Driving Device Applicaon on the user’s handsets (smart phones). The Applicaon can be quickly located by scanning the following QR Code.A) Download the AppDuring the setup of the Application, the user will need to enter the serial numbers of the Comm Device (PTE-5) and the Dock (DDD-1). These serial numbers can be located on the bottom of the devices as well as on the outside of the box as shown below. B) Find the labelsDDD-1DockSN 00000000PTE-5EliteSN 00000000Following the in-App instructions, scan the barcode (or manually enter serial number) for each device. C) Scan the barcodesFollow the instructions in the App to complete the device pairing and account setup.D) Complete Account SetupThe Emergency Override is failsafe to be used in the event the required phone has been lost, has a dead baery or is otherwise malfunconing. When the Emergency Override is used to start the vehicle, a message will be sent to the vehicle owner advising of its use. The DDD system may be bypassed by turning the key to the ignion posion and then off 5 mes in succession. The vehicle will then be permied to start without a docked handset. EMERGENCY OVERRIDE:

Navigation menu