Partner Tech OT200 HANDHELD TERMINAL User Manual

Partner Tech Corporation HANDHELD TERMINAL

Users Manual

OT-200User Manual
iCopyrightThis publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of PARTNER Tech Corp.DisclaimerThe information in this document is subject to change without notice. The manufacturer makes no revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes.Trademark recognitionAll product names used in this manual are the properties of their respective owners and are acknowledged.Federal Communications Commission (FCC)This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and the receiver.Connect the equipment onto an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.Shielded interconnect cables and a shielded AC power cable must be employed with this equipment to expressly approved by the system’s manufacturer could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement 1. This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 2. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device was tested for handheld operations with the device contacted directly to the human body. To maintain compliance with FCC RF exposure compliance requirements,avoid direct contact to the transmitting antenna during transmitting.Declaration of conformityThis device complies with part 15 of the FCC rules. Operation is subject to the following conditions:This device may not cause harmful interference, andThis device must accept any interference received, including interference that may cause undesired operation.
iiRevision history Version 1.0, July 2010About this manual This manual is intended for system administrators who are familiar with setting up a new system and installing programs. The manual consists of the following sections: Chapter 1 Getting Started: This section covers unpacking and checking the package contents, identifying components, charging the battery, installing the MicroSD card, and powering on the device. Chapter 2 Using The Device: This section provides information on how to use the device features. Chapter 3 Using The Accessories: This section provides information on how to use the accessories. Appendix: The appendix covers troubleshooting, information on having the OT-200 serviced and technical Safety information Before installing and using the OT-200, take note of the following precautions:SAR compliance for body-worn operations requires at least 2 cm of separation between the device and the user’s bodyRequest service for damaged products: Turn off the product, unplug it from the electrical outlet, and request service from a service partner under the following conditions: The power cord or plug is damaged. Liquid has been spilled into the product. An object has fallen into the product. The product has been exposed to rain or water. The product has been dropped or damaged. The product does not operate normally when you follow the operating instructions.Avoid hot areas: The product should be placed away from heat sources such as radiators, heat registers, Allow the product to cool: Allow the product to cool before removing covers and touching internal components.Avoid wet areas: Never use the product in a wet location.Avoid inserting objects into product: Never insert objects of any kind into slots or other openings in the product.Clean the product properly: Unplug the product from the wall outlet before cleaning it. Do not use liquid cleaners or aerosol cleaners. Use a soft cloth dampened with water for cleaning exterior components, but NEVER apply water directly to the product or to an LCD screen.
iiiUse the product with approved equipment: Use your product only with the computers and accessories Adjust the volume: Turn down the volume before using headphones or other audio devices.When device will not be used for a long period of time, please remove the battery, and store both device and battery in a cool, dark, and dry place. For storage over a long period of time, please place product in a dry box.SAR compliance for body-worn operations requires at least 2 cm of separation between the device and the user’s body.Battery Handling Precaution Do not attempt to disassemble or reconstruct the packs. The battery has integrated protection circuits and safety functions to avoid danger. If battery is damaged, it may rupture, generate heat, or cause smoke  Do not short circuit battery. Neither short connect the positive terminal and negative terminal with metals, nor carry or store the battery with metal objects. If the battery is short circuited, excessive large metals. Please cover the plug with waterproof cap when not using the battery. Do not incinerate or heat the battery. This will cause the insulator to melt, damage the gas release vent, and cause loss of safety function, or electrolyte ignition. Above mentioned matters will cause battery to  Do not use near high temperature areas.  Do not immerse the battery in water, seawater, or get it wet. This may cause internal short circuits to  If the battery protection circuit does not function properly due to high temperature, or it is broken, the battery will be charged at an abnormal current, and abnormal chemical reaction may occur, causing the battery to rupture, generate heat, or cause  If the battery is charged in unusual conditions, it will cause loss of safety functions, or abnormal chemical reactions, causing the  Do not try to damage the battery. Do not drive a nail into the battery, strike it with a hammer, or tread on  Do not attempt to solder anything onto the battery. This will cause the insulator to melt due to heat, or  Do not connect battery to a plug socket or car-cigarette plug. Connecting high voltage to the battery,  Do not use battery for powering other equipment. If the battery is used for powering other equipment, it  Do not touch a leaked battery directly. If battery leaks and hands touch leaked electrolyte, wash your hands with soap immediately. If leaked electrolyte gets into your eyes, do not rub them, and wash eyes
ivimmediately with fresh water. Consult a doctor immediately. time, let it stop charging. There is a possibility that the battery might be defective, and continued charging  Do not insert battery into a microwave or high pressure container. This may cause battery to deform, condition of the battery. If liquid leaks from the battery, or the battery give outs a bad smell,  Do not use an abnormal battery. If battery has a bad smell, changes color, deforms, or causes something wrong during usage, remove it from equipment or charger, and do not use. If an abnormal battery is used, it WARNINGWarning! Batteries may explode if not handled properly. Do not disassemble or dispose of them in fire. Keep them away from children. Follow local regulations when disposing of used batteries.娤⌈ᷴ㭊䢡✗㛛㏂曢㱇㛪㛰䇭䂟䙫⍘暑˛€⏖㛛㏂䂡⻇┭⻡字䙫䛟⏳曢㱇ㇽ䛟⏳❲⻶曢㱇˛媲ᾄ㓁⻇┭媑㗵㛟㢫何曢㱇˛㮦⿍䔏攀寖❲⏞䔜㱇㛛㍉ἁ㛰䇭䂟⍘晐⊈⾬㋰䅎寛㗵⣫何䔏⭳䙫䔜㱇˛㮦⿍㭊̧̯ẋ㏂̯̜͂̀曢㱇̤䇭䙡̱ͣ⍘晡̤͖̱̚͢˛壤怇㥔俬͆㎏⥏̱ͣ曢㱇⎯͇⏳Εͺέ͆曢㱇̀ẋ㏂̯̭̜̾ᷲ˛ὦ䔏⽳͆曢㱇ͪ㍏̾ͣ㘩͇壤怇㥔俬͆㋮䤡̓⽺̻̭̜̾ᷲ˛
vTABLE OF CONTENTSCHAPTER 1 GETTING STARTED ................................................ 1Unpacking the OT-200 ..................................................................................1Checking the package contents ....................................................................2Identifying components .................................................................................4Charging Cradle .............................................................................................8Setup the OT-200 ...........................................................................................9Using the cradle ...........................................................................................12Charge the device in cradle .........................................................................12Charge the battery in cradle .........................................................................12Changing the battery ....................................................................................13Using MicroSD cards ...................................................................................16Installing a MicroSD card .............................................................................16View the contents of a MicroSD card ...........................................................19CHAPTER 2 USING THE DEVICE ............................................. 21Entering text .................................................................................................21Shortcut menus ............................................................................................21Performing a reset........................................................................................22Opening and closing programs ....................................................................22Status icons..................................................................................................22Adjusting the volume ....................................................................................23Changing the device name ..........................................................................24Entering owner information ..........................................................................25Recalibrating the screen ..............................................................................26Setting the date and time .............................................................................27Turning WiFi, Bluetooth on or off .................................................................28Setting the screen orientation ......................................................................29Connecting to a WiFi network ......................................................................30Automatically connect to a WiFi network .................................................30Manually connect to a WiFi network ........................................................31Find your IP address ................................................................................32Specify the IP address and domain name servers (DNS) .......................32Lock OT-200.................................................................................................34Unlock OT-200 .............................................................................................35Synchronization............................................................................................36Synchronize your data with ActiveSync and Windows XP ...........................36Synchronize your data with ActiveSync and Windows Vista/ 7 ....................37
vi ...............................38 ..............................38 .............................38Install and remove programs........................................................................39CHAPTER 3 USING THE ACCESSORIES ............................... 41Attaching the stylus cord ..............................................................................41Attaching the hand strap ..............................................................................42Using the leather pouch ...............................................................................43Attaching the leather pouch cord .................................................................44Using the high quality stylus.........................................................................45APPENDIX .................................................................................. 47Troubleshooting ...........................................................................................47Tips for Troubleshooting ...............................................................................47General Problems .......................................................................................47Having the OT-200 Serviced .......................................................................48Guidelines for care and maintenance ..........................................................48Using the device ......................................................................................48Cleaning the device .................................................................................48Transporting and storing the device.........................................................48 ...............................................................................................49
49CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 ProfessionalDisplay 4.3” TFT LCD with Touch Screen, widescreen 800*480Memory 256MB Flash, 256MB SDRAMCommunication WiFi 802.11 b/gBluetooth 2.0 class 2Telecom standards  EDGE AtherosExtension slot Interface Mini-USB 2.0OtherInternal microphoneSpeakerFeaturesWireless roaming5510 LockBattery cover safety protectionRemote DesktopLock screenRuggedness IP541.2 meters drop testedEnvironmental Operating temperature: 0oC to 40oCStorage temperature: -20oC to 60oCBattery Dimensions  82 *133 * 19 mmWeight Approximately 245g with batteryOptional modules Accessories AC adaptor, Cradle, Battery Stylus cord, Hand strap, Leather pouch,Leather pouch cord, Shoulder strap, High quality stylusEMC: FCC / CE / 3C / BSMI / VCCI
2 CHAPTER 1 GETTING STARTEDChecking the package contents After you unpack the device check that the following items are included.OT-200 StylusBatteryHigh quality stylusAC adaptorCradlemini-USB to USB cable
49CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 ProfessionalDisplay 4.3” TFT LCD with Touch Screen, widescreen 800*480Memory 256MB Flash, 256MB SDRAMCommunication WiFi 802.11 b/gBluetooth 2.0 class 2Telecom standards  EDGE AtherosExtension slot Interface Mini-USB 2.0OtherInternal microphoneSpeakerFeaturesWireless roaming5510 LockBattery cover safety protectionRemote DesktopLock screenRuggedness IP541.2 meters drop testedEnvironmental Operating temperature: 0oC to 40oCStorage temperature: -20oC to 60oCBattery Dimensions  82 *133 * 19 mmWeight Approximately 245g with batteryOptional modules Accessories AC adaptor, Cradle, Battery Stylus cord, Hand strap, Leather pouch,Leather pouch cord, Shoulder strap, High quality stylusEMC: FCC / CE / 3C / BSMI / VCCI
4 CHAPTER 1 GETTING STARTEDIdentifying components This section describes the parts and connectors on the OT-200. Front panel components45123Figure 1.2 Front viewComponent Description1 2 3 4 4.3-inch touch screen5 Microphone
5Top and bottom panel components1Figure 1.3 Top and bottom viewComponent Description1 Top hand strap eyelet2 2.5mm microphone jack3 Mini-USB port4 Cradle connector5 DC power jack6 3.5mm headphone jack32465
6 CHAPTER 1 GETTING STARTEDLeft and right side componentsFigure 1.4 Left and right side view4123Connector Description1 Reset button2 Leather pouch strap eyelet3 Power button4 Stylus dock
7Back panel components4123Connector Description1 Top hand strap eyelet2 Speaker3 Battery cover4 Bottom hand strap eyeletFigure 1.5 Back view
8 CHAPTER 1 GETTING STARTEDCharging CradleThis section introduces the charging cradle for the OT-200. The charging cradle is used to charge the OT-200. A second slot is also available for charging a spare battery.Top and front view of the cradle4123Connector Description1 DC power connector2 Battery slot3 OT-200 socket4 Battery slot charging indicatorFigure 1.6 Top view of the cradleFigure 1.7 Front view of the cradle
9Setup the OT-200Refer to the following to setup the OT-200. 1. Remove the battery cover. Slide the cover downwards to open. Lift up to remove the battery cover.
10 CHAPTER 1 GETTING STARTED2. Install the battery.Align the battery connectors on the battery with the pins in the battery compartment and insert the battery.3. Replace the battery cover.Slide the battery cover back until it locks.4. Install the screw if required.
115. Insert the plastic hinge, or attach the hand strap.(Refer to Chapter 3 - Attaching the hand 6. Charge the battery.Open the power jack cover. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to the OT-200. It takes approximately 6 hours to fully charge the battery for the CAUTIONTo avoid damaging OT-200 or the AC adaptor, make sure all connectors are properly connected.7. Press Power Button for OT-200. To turn off OT-200. Press Power Button prompt, tap Power Off.
12 CHAPTER 1 GETTING STARTEDUsing the cradleThe charging cradle allows a more convenient way to charge OT-200. You can charge a spare battery Charge the device in cradle1. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to the power jack at the back of cradle.2. Insert OT-200 into the cradle with front of device on same side as front of cradle.3. When device is inserted into cradle correctly, the Power LED on top left of device should turn red. Device charging is complete when the device Power LED turns green.Charge the battery in cradle1. Plug the AC adaptor power cord into an electrical outlet, then connect the DC plug of the adaptor cable to the power jack at the back of cradle.2. Align the battery connectors on the battery with the pins in the second battery slot of the cradle, then install the battery in the direction of the arrow.3. When battery is inserted into cradle correctly, the battery LED on the cradle should light up red. Battery charging is complete when the battery LED on the cradle turns green.IMPORTANTTo protect and prolong the life of the battery, do not charge it for 24 hours or longer at a time.If battery is not used, please store in dry area, ideally with storage IMPORTANT
13Changing the batteryRefer to the following to change the battery.1. Press the Standby button to turn off the OT-200.2. Remove the plastic hinge or the bottom of the hand strap.Slide the plastic hinge or hand strap down and away from the battery cover.3. Remove the screw if the battery cover is locked. Please make sure to perform 3 complete full charge and discharge cycles to get optimal battery capacity. Failure to comply will result in shorter battery lifespan.IMPORTANT
14 CHAPTER 1 GETTING STARTED4. Remove the battery cover. Slide the cover down, then lift up to remove.5. Remove the battery by pulling on the plastic 6. Install the new battery.Align the battery connectors on the battery with the pins in the battery compartment and insert the battery.
157. Replace the battery cover.Slide the battery cover back until it locks.8. Reinstall the screw.9. Replace the plastic hinge or the bottom of the hand strap.
16 CHAPTER 1 GETTING STARTEDUsing MicroSD cardsUse MicroSD cards for: Expanding the memory of the OT-200 Adding functionalityThe OT-200 supports SDHC MicroSD cards.NOTESD cards must be purchased separately and are not included with the OT-200.Installing a MicroSD cardRefer to the following to install a MicroSD card.1. Press the Standby button to turn off the OT-200.2. Remove the plastic hinge or the bottom of the hand strap.Slide the plastic hinge or hand strap down and away from the battery cover.3. Remove the screw if the battery cover is locked.
174. Remove the battery cover. Slide the cover down, then lift up to remove.5. Remove the battery by pulling on the plastic 6. Slide the MicroSD slot clip horizontally to the open position.
18 CHAPTER 1 GETTING STARTED7. Flip the clip.8. Insert the MicroSD card into the slot with the label facing out.9. Flip the clip back down.10. Slide the clip to lock it.
19View the contents of a MicroSD cardRefer to the following to view the contents of a SD card.1. Tap 2. Tap File Explorer.3. Tap Storage Card to see a list of  If the OT-200 does not recognize your MicroSD card, make sure you card into the slot.
20 CHAPTER 1 GETTING STARTED
21CHAPTER 2USING THE DEVICE This chapter describes how to use OT-200 features. The following topics are described. Entering textYou can use the Input Panel to enter text. To use the Input Panel, tap the on the taskbar.Tap keys on the Input Panel to enter text.Shortcut menusA shortcut menu is displayed when you tap and hold an item. This menu displays the action you want to perform. To close a shortcut menu without performing an action, tap anywhere outside the menu.
22 CHAPTER 2 LEARNING THE BASICSPerforming a resetA reset stops all running applications, but does not erase any programs, saved data, or registry information.NOTEBe sure to close all running applications before performing a reset.To perform a reset:1. Locate the recessed Reset button on the device.2. Use the stylus to lightly press the Reset button.Opening and closing programsYou do not need to exit a program to open another or to conserve memory. The system manages memory automatically.To open a program, tap , and then select the required program from the desktop.In most cases, tap will close an application.Status iconsThere are status icons in taskbar. The following table lists the icons and their meanings.Icon StatusBattery chargingBattery level lowBattery level criticalWiFi connectedWiFi not connectedUSB connected
23Adjusting the volume1. Tap the status bar.2. Tap the Speaker icon.3. Move the system/ phone volume slider on the screen to the required volume level. Also you can switch to On/ Vibrate or Off.4. Tap the OK button.
24 CHAPTER 2 LEARNING THE BASICSChanging the device nameThe device name is used to identify the OT-200 in the following situations: Connecting with a computer Connecting to a networkRefer to the following to change the device name.1. About.2. Select the Device ID tab.3. Enter a name. The device name must begin with a letter, consist of letters from A to Z and numbers from 0 to 9, and should not contain spaces.4. Tap the OK button.
25Entering owner informationEnter your personal information, such as your name and address, so that the OT-200 can be returned to you if it is lost. Refer to the following to enter the information.1. Owner Information.2. personal information.
26 CHAPTER 2 LEARNING THE BASICSRecalibrating the screenIf your stylus seems to be out of sync with the screen, then recalibrate the screen using your stylus.1. Screen.2. On the General tab, tap the Align Screen button.3. Follow the displayed instructions to recalibrate. Please use the stylus to calibrate the screen for better accuracy.
27Setting the date and timeRefer to the following to set date and time.1. Tap the status bar.2. Tap the Clock icon.3. Change the date or time and select the correct time zone.4. Tap the OK button.
29Setting the screen orientationRefer to the following to set the screen orientation.1. 2. On the General tab select Portrait or Landscape. PortraitLandscape
30 CHAPTER 2 LEARNING THE BASICSConnecting to a WiFi networkWith wireless access, you can connect the device to the Internet. The OT-200 can connect to an IEEE 802.11b/g device or connect directly to other WiFi-enabled devices.Automatically connect to a WiFi networkWhen you turn on the WiFi radio, OT-200 automatically detects WiFi networks that are broadcasting their it manually. Before trying to connect to a WiFi network, determine if authentication information is needed by contacting your network administrator.To automatically connect to a WiFi network:1. Turn on the WiFi.2. Double tap or on the taskbar.3. Select the Wireless Information tab.4. Select an available network.5. Tap the Connect button.
316. Set the properties. Normally, all settings will be detected automatically. If necessary, you can change settings as follow. To use data encryption, select an encryption method from the Encryption list. To use authentication, select the authentication method from the Authentication list.7. Tap the OK button. Manually connect to a WiFi networkA wireless network can be added manually by entering the settings information to add the network. Contact your network administrator to determine if authentication information is needed before trying to connect to a WiFi network.To manually connect to a WiFi network:1. 2. Double tap or on the taskbar.3. Select the Wireless Information tab.4. Tap Add New...
32 CHAPTER 2 LEARNING THE BASICS5. Set the properties.6. Enter the SSID. To use data encryption, select an encryption method from the Encryption list. To use authentication, select the authentication method from the Authentication list.7. Tap the OK button. Find your IP address1. Double tap or on the taskbar.2. The WiFi IP address is displayed at the IP Information tab.Specify the IP address and domain name servers (DNS)The IP address and name server addresses are automatically assigned if DHCP in enabled on the wireless access point or network server. If your network does not automatically assign the addresses, ask your network administrator for the information and follow the instructions below.1. 
332. Double tap the Network and Dial-up Connections icon.3. Double tap the WiFi connection icon.4. Tap Specify an IP address.5. Enter IP address, Subnet Mask, Default Gateway.6. Tap the Name Servers tab on top7. Enter the DNS or WINS addresses.8. Tap the OK button.
34 CHAPTER 2 LEARNING THE BASICSLock OT-200private.NOTETo create or change the password1. 2. Select the Prompt if phone unused for check box.3. Tap the list next to the Prompt if phone unused for check box, and then tap the amount of time that you want.4. Tap the Password type list box, and then tap the type of password you want. Simple PIN is a 4-digit password that uses only the numbers 0-9. Strong alphanumeric is a pass-word that can have uppercase and lowercase letters, numbers, and symbols, such as punctua-tion marks.5. Tap the Password box, and then enter the password you want to use.6. password box, and then enter the password you want to use again.7. Tap OK Done.8. At the prompt, tap Yes.
35Unlock OT-200To unlock your phone1. Drag the lock slider to either edge of the screen.2. If you use a password, enter the password, and then click the icon for where you want to go: To go to the Desktop screen, tap Unlock. To go to your contacts,tap Con-tacts. To go to your e-mail, tap E-mail.
36 CHAPTER 2 LEARNING THE BASICSSynchronizationBy synchronizing OT-200 with your computer, you have access to the same information—your Microsoft or your computer. It’s a good idea to synchronize regularly.Before you begin, get the Mini-USB to USB cable, you’ll use it to download and install a program that syncs content between OT-200 and your computer.If your computer is running Windows Vista or 7, synchronization settings are managed through Windows WMDC.Synchronize your data with ActiveSync and Windows XP1. Install Microsoft ActiveSync. If your computer is running Windows XP or an earlier version, synchronization settings are managed through Microsoft ActiveSync. You can visit http://www.microsoft.com/windowsmobile for more information or to download Microsoft ActiveSync.2. Download and install ActiveSync on your computer.3. Plug OT-200 into the computer by using a Mini-USB to USB cable.4. 5. 
37Synchronize your data with ActiveSync and Windows Vista/ 71. Download and install WMDC on your computer. If your computer is running Windows Vista or 7, visit http://www.microsoft.com/windowsmobile to download WMDC.2. Plug OT-200 into the computer by using a Mini-USB to USB cable.3. 4. 
38 CHAPTER 2 LEARNING THE BASICS1. Connect OT-200 to the computer using a Mini-USB to USB cable.2. On the computer, select Start > Programs > ActiveSync.3. In the ActiveSync window, select Explore.4. Double-click My Windows Mobile-Based Device.5. 6. 7. Right-click in the folder that you want to move it to, and then click Copy, Cut, or Paste.8. If the File Conversion dialog box appears, click OK.1. Connect OT-200 to the computer using a Mini-USB to USB cable and wait for WMDC to launch automatically.2. Click File Management to open the Mobile Device folder for OT-200.3. 4. 5. Right-click in the folder that you want to move it to, and then click Copy, Cut, or Paste.6. If the File Conversion dialog box appears, click OK.
39Install and remove programsTo install programs on the OT-200:1. Use a Mini-USB to USB cable to connect the OT-200 to the computer.2. Follow the instructions in the Installation Wizard provided with the program you want to install.3. Check the screen on the OT-200 to see if any further steps are necessary to complete the program installation.To remove programs from the OT-200:1. Remove Program.2. Select the check boxes for programs you want to remove, and then tap Remove.
40 CHAPTER 2 LEARNING THE BASICS
41CHAPTER 3USING THE ACCESSORIES This chapter describes how to use the device accessories. Attaching the stylus cordRefer to the following to attach the stylus cord.1. Thread the small loop of the stylus cord through the strap eyelet on the stylus and pull the other end of the cord through the small loop until the cord is 2. Thread the other small loop of the stylus cord through the top hand strap eyelet on the device and use stylus pull the cord through the small loop until the 
42 CHAPTER 3 USING THE ACCESSORIESAttaching the hand strapRefer to the following to attach the hand strap.1. Insert the bottom of the hand strap into the slot at the bottom of the battery cover, until it clicks into place.2. Thread the end of the hand strap through the top hand strap eyelet on the device then fold and stick together. The hand strap length can be adjusted by sticking the Velcro to a higher or lower position on the strap.
43Using the leather pouchUsing the leather pouch to carry the OT-200 is a good way to keep it protected. Simply insert the device into the leather pouch as shown below.A belt clip located on the back of the leather pouch allows you to wear the OT-200 on your side. In addition, a shoulder strap can be attached to the two integrated rings on the back side.Shoulder strap is adjustableClip to your belt
44 CHAPTER 3 USING THE ACCESSORIESAttaching the leather pouch cordA leather pouch cord is provided to attach device to the leather pouch.1. Open the battery cover.2. Thread the small loop of the cord through the bottom corner strap eyelet on the device. Pull the other end of the cord through the small loop until the 3. Replace the battery cover.4. Lock the other end of the cord to one of the rings on the back of the leather pouch.5. To insert device into cradle for charging, simply detach as shown.
45Using the high quality stylusA high quality stylus is included for your convenience.
46 CHAPTER 3 USING THE ACCESSORIES
47APPENDIXThis appendix describes locating and solving problems that you may encounter while using the OT-200.TroubleshootingOften after time spent troubleshooting, the problem is traced to something as simple as a loose connection. Tips for Troubleshootingmore quickly. Try to pinpoint the problem and thus avoid replacing non-defective parts. For example, if you replace batteries and the problem remains, put the original batteries back and go to the next step.Keep a record of the steps you take when troubleshooting: The information may be useful when calling for technical support or for passing on to service personnel.General Problems Refer to the following for general problems you may encounter. PROBLEM SOLUTIONYou cannot turn on the device  Plug AC adaptor directly into device to check device is functioning. If device functions properly, then issue may be with the battery. Check that the battery is fully charged and properly installed into device.You have trouble charging the battery  Check that the AC adaptor is plugged in correctly to the DC jack on the device, and the other end into the wall outlet. If using the cradle for charging, check that the AC adaptor is plugged in correctly to the cradle and the wall outlet. Check for damage to the power cables. If battery has been used extensively and is old, replace with new battery and try again.You have trouble connecting to the Internet Check that device is connected to a WiFi network with the  Check if the WiFi network provides an IP address automatically via DHCP. If not, contact your network administrator for the relevant IP address, subnet, gateway, and DNS servers, which you need to enter manually.
48 APPENDIXWhy does the device operate slowly at times? Reset device. Does problem remain? If this solves problem, check if user installed applications are causing system to slow down. Check that enough free storage memory remains on device,  If device shows low storage memory, delete unnecessary Having the OT-200 Serviced If you are unable to solve the problem, you should have the device serviced. Pack the device in the original the device to the place you purchased it.Guidelines for care and maintenanceIt is recommended that you follow certain guidelines to prevent possible damage to the device and to keep it in a good condition.Using the device Avoid using the device in dusty and extremely high or low temperature environments. Do not spill water on the device or expose it to the rain. Avoid removing the battery without turning off the device. Do not apply strong force or shocks to the device. Keep the device and its accessories away from children. Do not insert metal objects into the charging/communications port of the device. This can short-circuit the battery and result in danger.Cleaning the device Use a soft, clean, and slightly moistened cloth to clean the device. Do not let water come into contact with the microphone, speaker, or with any of the connectors. Do not wipe the device with any corrosive liquid or coarse objects. This can damage the outer surface of the device.Transporting and storing the device Do not leave the device in extremely high or low temperature environments. If device is to be transported or stored for a long period of time, please remove the battery, and store both device and battery in a cool, dark, and dry place. Ideally, batteries should be stored at around need to be charged every 3 months to prevent battery degradation Batteries in storage need to be charged every 3 months to prevent battery degradation.
49CPU Samsung S3C6410 667 MHz processor Operating System Microsoft® Windows™ Mobile 6.5 ProfessionalDisplay 4.3” TFT LCD with Touch Screen, widescreen 800*480Memory 256MB Flash, 256MB SDRAMCommunication WiFi 802.11 b/gBluetooth 2.0 class 2Telecom standards  EDGE AtherosExtension slot Interface Mini-USB 2.0OtherInternal microphoneSpeakerFeaturesWireless roaming5510 LockBattery cover safety protectionRemote DesktopLock screenRuggedness IP541.2 meters drop testedEnvironmental Operating temperature: 0oC to 40oCStorage temperature: -20oC to 60oCBattery Dimensions  82 *133 * 19 mmWeight Approximately 245g with batteryOptional modules Accessories AC adaptor, Cradle, Battery Stylus cord, Hand strap, Leather pouch,Leather pouch cord, Shoulder strap, High quality stylusEMC: FCC / CE / 3C / BSMI / VCCI
50 APPENDIX

Navigation menu