Panasonic of North America 9TGCF-195 Personal Computer CF-19 Family User Manual CF 19CTQZZBM indb

Panasonic Corporation of North America Personal Computer CF-19 Family CF 19CTQZZBM indb

User Manual Summary for FCC Warning Notices

ContentsGetting StartedOPERATING INSTRUCTIONSPersonal ComputerModel No. CF-19 seriesIntroduction ................................................................. 2Read Me First ............................................................. 3Description of Parts ..................................................10First-time Operation ..................................................13Useful InformationOn-screen Manual ....................................................16Handling and Maintenance .......................................17Hard Disk Backup Function (Recover Pro) ..............19Hard Disk Data Erase Utility .....................................21Reinstalling Software ................................................22TroubleshootingError Code/Message ................................................24Troubleshooting (Basic) ............................................25Hardware Diagnostics ..............................................29AppendixLIMITED USE LICENSE AGREEMENT ...................32Specifi cations ...........................................................34LIMITED WARRANTY ..............................................36Please read these instructions carefully before using this product and save this manual for future use.For further information about the com-puter, you can refer to the on-screen manual.To access the on-screen manual Î page 16 “On-screen Manual”Getting StartedUseful InformationTroubleshootingAppendix
3Getting StartedRead Me FirstModels for U.S.A.Federal Communications Commission Radio Fre-quency Interference StatementNote: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential instal-lation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interfer-ence will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dif-ferent from that to which the receiver is connected. Consult the Panasonic Service Center or an experi-enced radio/TV technician for help.WarningTo assure continued compliance, use only shielded inter-face cables when connecting to a computer or peripheral. Also, any changes or modifications not expressly ap-proved by the party responsible for compliance could void the user’s authority to operate this equipment.FCC RF Exposure Warning: This equipment is provided with PC Card slot that could be used with wireless transmitters, which will be specifi-cally recommended when they become available. Other third-party wireless transmitters have not been RF exposure evaluated for use with this computer and may not comply with FCC RF exposure requirements.<Only for model with wireless LAN/Bluetooth> This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment may not be co-located or operated with any other antenna or transmitter. This equipment has been approved for portable operation, and unless otherwise advised in separate supplemental instructions for individual wireless transmitter(s), requires minimum 1.5 cm spacing be provided between antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation. This equipment may use multiple installed transmitters, which may be capable of simultaneous transmission. This equipment is provided with external antenna connector(s) for connection to optional Car Mounter or Port Replicator for mobile external mounted antenna(s). External antenna(s) must be professionally installed and cannot exceed recommended maximum antenna gain as described in individual provided supplement instructions for wireless transmitters. Also, user must maintain mini-mum 20 cm spacing between external antenna(s) and all person’s body (excluding extremities of hands, wrist and feet) during wireless modes of operation.<Only for model with wireless LAN> WLAN external antenna connector is intended for con-nection to Radiall/Larsen WLAN Base Whip antenna, type NM05E2400BKTNC with 5 dBi antenna. <Only for model with wireless WAN> WWAN external antenna connector is intended for professional installation and should not exceed maxi-mum antenna gain of 9.85 dBi for 824.7 - 848.31 MHz operation and 8.34 dBi for 1851.25 - 1908.75 MHz operation.This device complies with Part 15 of the FCC Rules. Op-eration is subject to the following two conditions:(1) This device may not cause harmful interference, and(2) This device must accept any interference received, including interference that may cause undesired op-eration.Responsible Party: Panasonic Corporation of North America One Panasonic Way Secaucus, NJ 07094 Tel No:1-800-LAPTOP5 (1-800-527-8675)6-M-1FCC Regulation Notice for modem This equipment contains a FCC approved modem.1. This equipment complies with CFR47 Part 68 rules. On the computer is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If re-quired, this information must be provided to the tele-phone company.2. An FCC compliant telephone cord and modular plug is provided with this equipment. This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. See Installation Instruc-tions for details.3. The REN is used to determine the quantity of devices which may be connected to the telephone line. Ex-cessive RENs on the telephone line may result in the devices not ringing in response to an incoming call. In most, but not all area, the sum of RENs should not ex-ceed five (5.0). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company.4. If your telephone equipment cause harm to the tele-phone network, the telephone company will notify you in advice that temporary discontinuance of service may be required. But if advice notice isn’t practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is neces-sary.5. The telephone company may take changes in its facili-ties, equipment, operations or procedures that could affect the operation of the equipment. If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service.6. If trouble is experienced with this equipment, for repair or warranty information, please contact Panasonic Corporation of North America at DIAL TOLL FREE 1-800-LAPTOP5 (1-800-527-8675). If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equip-ment until the problem is resolved.7. There are no user serviceable parts contained in this equipment.8. This equipment may not be used on coin service pro-vided by the telephone company. Connection to party lines is subject to state tariffs.
5Getting StartedCSA C22 2 NO.213-conforming model. (The model which has description of “CSA C22 2 NO.213” in the bottom of the computer.)z THIS EQUIPMENT IS SUITABLE FOR USE IN CLASS I, DIVISION2, GROUPS A, B, C, AND D OR NON-HAZARDOUS LOCATIONS ONLY.z WARNING-EXPLOSION HAZARD-SUBSTITUTION OF COMPONENTS MAY IMPAIR SUITABILITY FOR CLASS I, DIVISION2.z When connecting and using a device manufactured by a third party, enquire to the manufacturer as to wheth-er the device suits CLASS I, DIVISION2. 33-Ca-1<Only for model with wireless LAN/Bluetooth>Industry CanadaThis product complies with RSS210 Industry Canada.Operation is subject to the following two conditions;(1) this device may not cause interference, and(2) this device must accept any interference, including inter-ference that may cause undesired operation of the device.30-Ca-1-1<Only for model with wireless LAN>This product (local network devices) for the band 5150-5250 MHz is only indoor usage to reduce potential for harmful interference to co-channel Mobile Satellite systems.High power radars are allocated as primary users (meaning they have priority) of 5250-5350 MHz and 5650-5850 MHz and these radars could cause interference and/or damage to LELAN devices.30-Ca-2-1This device has been designed to operate with an anten-na having a maximum gain of 2.15 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry Canada. The Required antenna impedance is 50 ohms.To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that required for successful communication. 25-Ca-1-1<Only for model with Bluetooth>This Class B digital apparatus complies with Canadian ICES-003.Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 7-M-1Models for Europe<Only for model with a “CE” mark on the bottom of the computer>Declaration of Conformity (DoC)“Hereby, we declare that this Personal Computer is in compliance with the essential requirements and other relevant provisions of the Directive 1999/5/EC.”Hint:If you want to get a copy of the original DoC of our products which relates to the R&TTE, please con-tact our web address: http://www.doc.panasonic.deContact:Panasonic Services EuropeA Division of Panasonic Marketing Europe GmbHPanasonic Testing CentreNetwork connection.The terminal equipment is intended for connection to the following public network;In all the countries of European Economical Area;- Public Switched Telephony NetworksTechnical Features.The terminal equipment includes the following features;- DTMF dialing- Maximum bitrate receiving mode: 56 kbit/s- Maximum bitrate sending mode: 33.6 kbit/sThis product is designed to interwork with the Public Switched Telecommunication Networks in UK, Ireland, Nether-lands, Sweden, Denmark, Finland, Switzerland, Luxembourg, Belgium, France, Germany, Spain, Portugal, Iceland, Greece, Italy, Norway and Austria. 18-E-1Compliance Notice - CE MarkThis equipment is in conformance with the requirements of the European Council Directive listed below:73/23/EEC Low Voltage Directive with amendment 93/68/EEC89/336/EEC EMC Directive with amendments 92/31/EEC and 93/68/EEC1999/5/EC R&TTE21-E-1
This manual contains supplementary instructions regarding the use of the computer. It explains the cases where the operation of thecomputer differs from that in the Operating Instructions.Your computer is equipped with Wireless LAN enabling you to communicate using radio frequencies.Supplementary Instructionsfor Wireless LANFCC Radio Frequency Interference RequirementsThis product is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range.FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interferenceto co-channel Mobile Satellite systems.High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations cancause interference with and /or damage this product.SpecificationsData transfer ratesStandards supportedTransmission methodWireless channels usedRF frequency bandIEEE802.11a: 54/48/36/24/18/12/9/6Mbps (automatically switched)IEEE802.11g: 54/48/36/24/18/12/9/6Mbps (automatically switched)IEEE802.11b: 11/5.5/2/1 MbpsIEEE802.11a/IEEE802.11g/IEEE802.11bOFDM system, DSSS systemIEEE802.11a: Channels 36 to 64, 149 to 165IEEE802.11b/IEEE802.11g: Channels 1 to 11IEEE802.11a: 5.18~5.32GHz, 5.745~5.825GHzIEEE802.11g/IEEE802.11b: 2412~2462MHz
1ContentsPrecautions ...............................................................................2Names and Functions of Parts .................................................4Supplementary Instructionsfor HSDPA/UTMS Modem Model No. CF-19 SeriesPersonal Computer
1Car MounterAuto monter䔺䕑῵ഫカーマウンターENGLISH OPERATING INSTRUCTIONS .......................2DEUTSCH BEDIENUNGSANLEITUNG ...........................5FRANÇAIS INSTRUCTIONS D’UTILISATION ..................9ㅔԧЁ᭛ Փ⫼䇈ᯢк ....................................................13ⅺ㋤ʑᄽ ᪡԰ᣛफ ........................................................16䚐ạ㛨 㦤㣅G㫴㾜㉐ ................................................... 19日本語 取扱説明書 ....................................................22Model No. CF-WEB184 SeriesൟোCF-WEB184 ㋏߫ WEB184.indd 1WEB184.indd 1 2006/11/01 9:27:312006/11/01 9:27:31
3Description of PartsA. Security lock LOCKYou can connect a Kensington cable. Refer to the instruction manual of the cable.B. LAN port C. USB port D. Serial port E. External display port F. Headphone jack G. Microphone jack H. DC-IN jack DC IN 16VI. Key insertion slot J. Dock indicator DOCKEDK. LatchL. Lever DOCK UNDOCKThe lever is locked when the key is inserted and turned toward side. When the computer has been installed, be absolutely sure to lock this lever by turning the key toward side.NOTE The lock was turned to side in the default setting. When installing the computer, confi rm that the lever is slid toward the UNDOCK side.Bottom SideA. External wireless WAN antenna port WWAN (optional)B. External wireless LAN/GPS antenna port WLAN/GPS (optional)WEB184.indd 3WEB184.indd 3 2006/11/01 9:27:332006/11/01 9:27:33
4Installation holes are provided in the areas indicated by the arrows in the fi gure above.Precautions for Installing the Car Mounter Do Not Install This Product in Unstable StateIf balance of the computer is lost, it may fall over or drop, resulting in an injury. Do Not Install This Product Wherever There is a Lot of Water, Moisture, Steam, Dust, Oily Vapors, etc. Otherwise, possibly resulting in fi re or electric shock.Dimensional DrawingBottom Side The ends of the screws are protrud-ing. Take care to protect your fi ngers, etc. from their sharp points when in-stalling the Car Mounter.CAUTION Install the Car Mounter horizontally.WEB184.indd 4WEB184.indd 4 2006/11/01 9:27:332006/11/01 9:27:33

Navigation menu