Panasonic of North America 11AR1201 ACTIVE SUBWOOFER User Manual SB HWA350 Part 2

Panasonic Corporation of North America ACTIVE SUBWOOFER SB HWA350 Part 2

User Manual_SB-HWA350_(Part 2)

Getting startedRQT9670 17Connect the speaker cables. ≥Insert the wire fully, taking care not to insert beyond the wire insulation.≥Place the speaker that is connected with the speaker cable with a red connector on the observers’ right, and connect with the speaker cable with a white connector on the observers’ left.To prevent the speakers from falling, it is recommended, as an additional protection measure, to attach the speakers to the wall or table with a fall prevention cord (hereafter “cord”).≥Consultation with a qualified housing contractor concerning the appropriate procedure when attaching to a concrete wall or a surface that may not have strong enough support is recommended (>11, 13). Improper attachment may result in damage to the wall and speakers, and personal injury.≥Use a cord of less than ‰2.0 mm (5/64q), which is capable of supporting over 10 kg (22.05 lbs).≥Keep the screws out of reach of children to prevent swallowing.≥Make sure that the slack of the cord is minimal.Additional speaker fall prevention measuresWhen attaching the speakers to a wallCord Screw eye Wall TVInsert the wire fully.r: Whites: Blue linePress into the groove.PushBack of the baseWall-mounted speakersHorizontal placementWall-mounted speakersVertical placementSC-HTB350_RQT9670_mst.book Page 17 Tuesday, December 20, 2011 2:05 PM
18 RQT9670When placing the speakers on a tableHorizontal placementVertical placementCordScrew eye≥Depending on the placement of the speakers, the screwing position of the screw eye may differ.WallApprox. 150 mm (5 29/32q)SC-HTB350_RQT9670_mst.book Page 18 Tuesday, December 20, 2011 2:05 PM
Getting startedRQT9670 19Step 3 Connections≥Turn off all equipment before connection and read the appropriate owner’s manual.Do not connect the AC power supply cord until all other connections are complete.You can direct the audio signal from the connected Blu-ray Disc playerTM, DVD player, Set Top Box, etc. to this system.Connection with the TV≥When you use the optical digital audio cable, insert the tip correctly into the terminal.OPTICAL OUTSPEAKERSAUXDIGITALAUDIOINTV(OPT1)AC INDIGITALAUDIOINTV(OPT1)Main unitTVOptical digital audio cableConnection with other devicesHigh quality audioStandard quality audioOPTICAL OUTSPEAKERSAUXDIGITALAUDIOINBD/DVD(OPT2)DIGITALAUDIOINBD/DVD(OPT2)AC INMain unite.g., Blu-ray Disc playerTMTVRefer to the operating instructions of the respective devices for the optimal connectionOptical digital audio cableSPEAKERSAUXDIGITALAUDIOINAC INRLSPEAKERSDIGITALAUDIOINAUXRLLR AUDIO OUTe.g., Set top boxMain unitTVAudio cableRefer to the operating instructions of the respective devices for the optimal connectionSC-HTB350_RQT9670_mst.book Page 19 Tuesday, December 20, 2011 2:05 PM
20 RQT9670Match the connector shape and connect to the terminals of the same color.≥Connect only after all other connections are complete.≥The main unit and active subwoofer consume a small amount of AC power, even when it is turned off (this unit: approx. 0.1 W, active subwoofer: approx. 0.1 W). In the interest of power conservation, if you will not be using this system for a long time, unplug it from the household AC outlet.Speaker cable connectionREDRight speaker channel (R)WHITELeft speaker channel (L)AC power supply cord connectionAC power supply cord To a household AC outletInstall this unit so that the power cord can be unplugged from the socket outlet immediately if any problem occurs.Saving energyThe main unit is designed to conserve its power consumption and save energy.≥The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx. 30 minutes.DIGITALAUDIOINAC INSPEAKERS6R LAUXSPEAKERS 6R LMain unitDIGITALAUDIOINAC INSPEAKERSAUXAC IN AC IN Main unitActive subwooferSC-HTB350_RQT9670_mst.book Page 20 Tuesday, December 20, 2011 2:05 PM
Getting startedRQT9670 21Preparation≥Turn on the main unit.Press [BÍ CI].Check that the wireless link is activated.WIRELESS LINK indicator lights≥Red:The wireless link is not activated.≥Green:The wireless link is activated.The unit will still consume a small amount of power even when it is turned off (B, Í)With the Bluetooth® connection you can output the audio from the connected wireless device.Preparation≥Turn on the Bluetooth® feature of the device and place the device near this unit.Press [, j PAIRING].≥“” indicator will blink quickly.Select “SC-HTB350” from the Bluetooth® device’s Bluetooth® menu.≥Refer to the operating instructions of the Bluetooth® device for further instruction on how to connect a Bluetooth® device.≥Once the Bluetooth® device is connected, the “ ” indicator stops flashing and lights up.≥If prompted for the passkey on the Bluetooth® device, enter “0000”.Press [, j PAIRING].Press and hold the [ , j PAIRING] until the “ ” indicator flashes quickly.Repeat step 2 of “Pairing a device”.≥You can register up to 6 devices with this unit. If a 7th device is paired, the device that has not been used for the longest time will be replaced.≥This unit can only be connected to one device at a time.≥To change the sound quality, refer to “Bluetooth® communication mode” on page 24. Active subwoofer wireless connectionBluetooth® connectionPairing a devicePairing additional devicesSC-HTB350_RQT9670_mst.book Page 21 Tuesday, December 20, 2011 2:05 PM
22 RQT9670Operatio nsUsing this unitPreparation≥Turn on the TV and/or connected device.Press [Í] to turn on the main unit.Select the source.≥This remote control cannot be used to control the operations of the connected devices.∫When “ ” is selected as the sourceOn the Bluetooth® device:Select this unit as the output source of the Bluetooth® device and start the playback.≥Make sure that the Bluetooth® device is already paired with this unit. (>21)≥Playback may pause when a different source is selected.∫When “BD/DVD” is selected as the sourceOn the connected device:Select the TV’s input for this unit and start the playback on the connected device.∫When “AUX” is selected as the sourceOn the connected device:Select the TV’s input for the device connected to “AUX” terminal and start the playback on the connected device.Adjust the volume and sound effect level.∫To adjust the volume of the systemPress [iVOL j].≥Volume range: 1 to 100§∫To adjust the dialog effect levelThis setting will change the level of the Clear-mode dialog effect. (>23)1Press [iDIALOG LEVEL j] to display the current level.2 While the level is displayed:Press [iDIALOG LEVEL j] to adjust the level.§∫To adjust the subwoofer level1Press [iSUBWOOFER j] to display the current level.2 While the level is displayed:Press [iSUBWOOFER j] to adjust the level.§≥The level indication pattern is the same as dialog effect level.∫To mute the soundPress [MUTE]≥While muting, the audio format indicators blink simultaneously.≥To cancel, press the button again or adjust the volume.≥Muting is canceled if the main unit is turned off.§The audio format indicators blink from left to right (i) or from right to left (s) while adjusting.The indicators will not blink when it has reached the maximum or minimum.≥If there is sound coming out of the TV’s speakers, reduce the volume of the TV to its minimum.≥If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically lower the volume to the middle (50) when the main unit is turned on (Volume limitation). To turn this function off, refer to page 25.Press To select[TV] “TV”[] “ ” (Bluetooth®)[INPUT SELECTOR]“TV”# “BD/DVD”#“AUX”^-------------- “”(----------}DIALOG LEVELLINK MODEPAIRING----INPUTSELECTORIndication Effect level4Highest321LowestIf the main unit does not operate as expected or sound is unusual, return the settings to the factory preset and operate the system again. (>26)SC-HTB350_RQT9670_mst.book Page 22 Tuesday, December 20, 2011 2:05 PM
OperationsRQT9670 23This system provides a feeling that the sound and the image are as one. The 3D sound effect will be applied to Multi-channel audio sources as a factory preset.Dolby Virtual Speaker and the 3D surround effects can be turned off and on by changing the audio output mode settings.As a factory preset, Dolby Virtual Speaker and the 3D surround effects will be applied to Multi-channel audio sources, such as those from a Blu-ray Disc playerTM or DVD player, etc.By changing the audio output setting, it is possible to apply the Dolby Virtual Speaker and 3D surround effects to 2ch audio sources, such as the audio from the TV.Press and hold [MUTE] for more than 2 sec.≥The indicator for the current setting blinks for 10 sec.While the indicator is blinking, press [MUTE] again to change the setting.≥The setting changes each time [MUTE] is pressed.§1 Depending on the audio source, Dolby Virtual Speaker and 3D surround effect settings are automatically adjusted.§2 This indicator will also light when the audio source is Multi-channel audio.When using the optical digital audio cable, Dolby Virtual Speaker and the 3D surround effect will be temporarily canceled if the audio signal’s sampling frequency is greater than 48 kHz.3D sound3D soundDolby Virtual SpeakerWith this effect you can enjoy a surround sound effect similar to 5.1ch.3D surround effectAdding to the Dolby Virtual Speaker effect, Panasonic has applied its own sound field controlling technology to expand the sound field forwards, backwards, upwards, and downwards, providing a sound with depth and force that better matches 3D images.Clear-mode dialogSports commentary and dialogs from TV dramas are heard as if the sound is coming from the TV, giving the feeling that the sound and the image are one.Also, the dialog will stand out from the other sounds during normal volume playback and when the volume is lowered for night time viewing.e.g., Image of 3D sound fieldAudio output modesTo change the audio output modeAudio output modeDolby Virtual Speaker and 3D surround effectMulti-channel mode The effects are applied to all audio sources.Auto mode (Direct mode)§1(Factory preset)The effects are applied to Multi-channel audio sources.The effects are not applied to 2 channel audio sources.2ch mode The effects are not applied to any audio source.2SC-HTB350_RQT9670_mst.book Page 23 Tuesday, December 20, 2011 2:05 PM
24 RQT9670Advanced operationsChange the dual audio from main to secondary.Confirm the digital audio output setting on the connected TV or player, etc. is set to “Bitstream”.Press and hold [TV] for more than 2 sec.While the indicator of the current setting is blinking, press [TV] to change the setting.≥The indicator for the current setting blinks for 10 sec.≥The setting works only when the dual audio is available in the audio source.≥The setting is maintained until it is changed again.≥The same setting is used for all digital audio sources.With this function, you can prevent sudden loud sounds. The output will be reduced automatically when the input exceeds a certain level. Press and hold [INPUT SELECTOR] on remote controller for more than 2 sec.≥The indicator for the current setting blinks for 10 sec.While the indicator is blinking, press [INPUT SELECTOR] to change the setting.≥The setting changes each time [INPUT SELECTOR] is pressed.≥The setting is maintained until it is changed again.≥Default setting of this function is OFF.You can select different modes to suit the type of connections which emphasis on connectivity or high quality audio.≥Make sure that a Bluetooth® device is already paired with this unit. (>21)Disable the Bluetooth® connection of the device.≥“” indicator will blink slowly.Press [LINK MODE, ] to display the current mode.≥The indicator for the current setting blinks for 10 sec.While the mode is displayed, press [LINK MODE, ] to select the mode.≥The setting changes each time [LINK MODE, ] is pressed.≥The setting is maintained until it is changed again.Depending on your preference, It is possible to use only the Dolby Virtual Speaker effect by turning off the 3D surround effect and the clear-mode dialog effect.Press and hold [TV] on the remote control and [VOL r] on the main unit for more than 2 sec.≥The indicator for the current setting blinks for 10 sec.While the indicator is blinking, press [TV] to change the setting.≥The setting changes each time [TV] is pressed.≥This setting will be reset to on when this system is turned off.≥When off is selected, the dialog effect level cannot be adjusted.Changing the dual audio: Main: Secondary (SAP: Secondary Audio Program), : Main and secondaryAuto gain controlDolby Digital indicator blinks:Auto gain control is on.PCM indicator blinks:Auto gain control is off.Bluetooth® communication modeMODE1: (Factory preset)Emphasis on connectivityMODE2: Emphasis on audio qualityTo turn off the 3D surround effect and clear-mode dialog effectDolby Digital indicator blinks:3D surround effect and clear-mode dialog effect is on.PCM indicator blinks:3D surround effect and clear-mode dialog effect is off.SC-HTB350_RQT9670_mst.book Page 24 Tuesday, December 20, 2011 2:05 PM
OperationsRQT9670 25∫Remote control codeWhen other Panasonic devices respond to this system’s remote control, change the remote control code on the main unit and the remote control.Preparation≥Turn off all other Panasonic products.≥Turn on the main unit.Change the remote control code to code 2:1 Aim the remote control at this system’s remote control sensor.2 Press and hold [MUTE] and [ ] on the remote control for more than 4 sec.≥All the indicators will blink for 10 sec when the code of this system is changed.≥The setting is maintained until it is changed again.≥If this system does not operate after changing the code, repeat steps 1 and 2.≥To change the remote control code to code 1, repeat the steps above, but replace [] with [TV]. ∫To reduce the clear-mode dialog effectWhen the dialog does not sound natural while the volume is set low, for example, It is possible to reduce the dialog enhancing effect as follows:Press and hold [TV] on the remote control and [sVOL] on the main unit for more than 2 sec.≥All the indicators will blink once when the clear-mode dialog effect is reduced.≥Even if clear-mode dialog effect is reduced, dialog effect level is still adjustable.∫To turn off the volume limitationIf a state of the lowered volume disturbs you every time this system turns on, for example, it is possible to turn off this function as follows:Press and hold [MUTE] on the remote control and [VOL r] on the main unit for more than 2 sec.≥All the indicators will blink once when the volume limitation is turned off.The settings of the clear-mode dialog effect and the volume limitation remain intact even if you switch this system to standby mode. To turn these 2 functions back on, this system must be set back to the factory preset. (>26)OthersThe following settings are unnecessary under general usage conditions of the system.SC-HTB350_RQT9670_mst.book Page 25 Tuesday, December 20, 2011 2:05 PM
26 RQT9670Referenc eTroubleshootingBefore requesting service, make the following checks. If you are in doubt about some of the check points, or if the solutions indicated in the following guide do not solve the problem, refer to “Customer Services Directory (United States and Puerto Rico)” on page 31.No power.≥Insert the AC power supply cord securely. (>20)≥After turning the main unit on, if the indicators blink and the main unit immediately turns off, unplug the AC power supply cord and consult your dealer.The remote control does not work properly.≥The battery is depleted. Replace it with a new one. (>7)≥It is possible that the insulation sheet has not been removed. Remove the insulation sheet. (>7)≥It may be necessary to set the code of the remote control again after changing the battery of the remote control. (>25)≥Use the remote control within the correct operation range. (>7)The “TV” indicator blinks.Remove the AC power supply cord and consult your dealer. If there are any other indicators blinking, be sure to inform your dealer about the blinking indicators.The main unit is automatically switched to standby mode.The main unit will automatically switch to standby mode when no signal is input and no operation is performed for approx. 30 minutes. (>20)Pairing cannot be done.Check the Bluetooth® device condition.The device cannot be connected.≥The pairing of the device was unsuccessful. Try pairing the device again.≥The pairing of the device has been replaced. Pair the device again. (>21)≥The system might be connected to a different device. Disconnect the other device and try pairing the device again.The device is connected but audio cannot be heard through the system.For some built-in Bluetooth® devices, you have to set the audio output to “SC-HTB350” manually. Read the operating instructions for the device for details.Sound from the device is uneven.≥The device is out of the 10 m (33 ft) communication range. Bring the device closer to the main unit.≥Remove any obstacle between the main unit and the device.≥Switch off any wireless LAN device.≥Select “MODE 1” for stable communication. (>24)No sound (or image).≥Turn muting off. (>22)≥Check the connections to the other devices. (>19) ≥Make sure that the received audio signal is compatible with this system. (>29)≥Turn this system off and then on again.≥If the connections are correct, there might be a problem with the cables. Redo the connections with different cables.≥Check the audio output settings on the connected device.The dual audio cannot be changed from main to secondary.If the audio received from the connected device is not “Dolby Dual Mono” or the output setting is not “Bitstream”, the setting cannot be changed from this system. Change the setting on the connected device.The volume is lowered when this system is turned on.If the main unit is turned off with the volume setting in the greater half (above 50), the main unit will automatically lower the volume to the middle (50) when the main unit is turned on. (>25)To return to the factory preset.While the main unit is on, press [Í/I] on the main unit for more than 4 sec.(All the indicators will blink twice when the main unit is reset.)If the system does not operate as expected, returning the settings to the factory preset may solve the problem.≥The remote control code will return to “1” when the main unit is returned to the factory preset. To change the remote control code, refer to page 25.General operationBluetooth®SoundSC-HTB350_RQT9670_mst.book Page 26 Tuesday, December 20, 2011 2:05 PM
ReferenceRQT9670 27The dialog is too persistent or the dialog does not sound natural.This system has a function to make the dialog stand out when the volume is low. (>25)There is no audio.The power of the main unit turns off automatically.(When the main unit detects a problem, a safety measure is activated and the main unit automatically switches to standby mode.)≥There is a problem with the amplifier.≥Is the volume extremely high?If so, lower the volume.≥Is this system placed in an extremely hot place?If so, move this system to a cooler place and wait a few moments and then try to turn it on again.If the problem persists, confirm the TV indicator and AUX indicator blink, turn the system off, remove the AC power supply cord and consult your dealer. Please be sure to remember the indicators that were blinking and inform the dealer.No power.Ensure the AC power supply cord of the active subwoofer is connected properly.After turning the subwoofer on, it immediately turns off.Unplug the AC power supply cord and consult your dealer.No sound from the subwoofer.≥Check that the active subwoofer is turned on.≥Check that the wireless link indicator lights green. (>21)The wireless link indicator lights red.≥There is no link between this unit and the active subwoofer.jCheck that this unit is turned on.jTurn the active subwoofer off and then back on. Alternatively, turn the active subwoofer off, disconnect the AC power supply cord and then reconnect it.≥The active subwoofer and the main unit may not be paired correctly. Try the following operation. (Wireless pairing)1Turn on the main unit and active subwoofer.2Press [ID SET] on the rear of the active subwoofer. (The WIRELESS LINK indicator will light red and green alternately.)3Press and hold [INPUT SELECTOR] on remote control and [VOL r] on the main unit for more than 2 sec. (The BD/DVD indicator will blink and audio format indicators light up in sequence.)≥When the wireless pairing is successful, BD/DVD indicator will stop flashing and WIRELESS LINK indicator lights green. 4Turn the main unit off and on.≥Consult your dealer if the problem persists.About Bluetooth®∫Frequency band usedThis unit uses the 2.4 GHz frequency band.∫Certification of this device≥This system conforms to frequency restrictions and has received certification based on frequency laws. Thus, a wireless permit is not necessary.≥The action below are punishable by law in some countries:jTaking apart or modifying the unit.jRemoving specification indications.∫Restrictions of use≥Wireless transmission and/or usage with all Bluetooth® equipped devices is not guaranteed.≥All devices must conform to standards set by Bluetooth SIG, Inc.≥Depending on the specifications and settings of a device, it can fail to connect or some operations can be different.≥This system supports Bluetooth® security features. But depending on the operating environment and/or settings, this security is possibly not sufficient. Transmit data wirelessly to this system with caution.≥This system cannot transmit data to a Bluetooth® device.∫Range of useUse this device at a maximum range of 10 m (33 ft).The range can decrease depending on the environment, obstacles or interference.∫Interference from other devices≥When other devices use the same frequency as this system, this system may operate incorrectly or the sound may be distorted.≥To prevent interference from other devices:jKeep the system away from other devices that emit radio frequency interference.jDo not use this system and a wireless LAN device at the same time. Switch off any wireless LAN device.∫Intended usage≥This unit is for normal, general use only.≥Do not use this system near an equipment or in an environment that is sensitive to radio frequency interference (example: airports, hospitals, laboratories, etc).Active SubwooferPanasonic bears no responsibility for data and/or information that is compromised during a wireless transmission.SC-HTB350_RQT9670_mst.book Page 27 Tuesday, December 20, 2011 2:05 PM
28 RQT9670Indicator illuminationThe indicators display the condition of this system by flashing. The indicator patterns illustrated below are displayed during normal operational conditions. They do not refer to the indications of a problem. Refer to “Troubleshooting” (>26) if the indicators do not light up as illustrated below.§The selected source indicator will also light.Indicator DescriptionThe indicators blink from left to right (i) or from right to left (s).≥When the speaker volume, the dialog effect level, or the subwoofer level is adjusted (>22)The indicators blink simultaneously.≥When “MUTE” is on (>22)The indicator blinks for 10 sec.≥When the audio output mode is Multi-channel mode (>23)≥When 3D surround effect and clear-mode dialog effect are on (>24)≥When the dual audio setting is Main (>24)≥When the auto gain control is on (>24)≥When the Bluetooth® communication is mode 1 (>24)≥When the dialog effect level or the subwoofer level is 1(>22)The indicators blink for 10 sec.≥When the audio output mode is Auto mode (>23)≥When the dialog effect level or the subwoofer level is 2 (>22)The indicator blinks for 10 sec.≥When the audio output mode is Auto mode (>23)The indicators blink for 10 sec.≥When the dialog effect level or the subwoofer level is 3 (>22)The indicator blinks for 10 sec.≥When the audio output mode is 2ch mode (>23)≥When 3D surround effect and clear-mode dialog effect are off (>24)≥When the dual audio setting is Secondary (SAP: Secondary Audio Program) (>24)≥When the auto gain control is off (>24)≥When the Bluetooth® communication is mode 2 (>24)≥When the dialog effect level or the subwoofer level is 4 (>22)The indicators blink for 10 sec.≥When the dual audio setting is Main and Secondary (>24)The indicators blink for 10 sec.≥When the remote control code is changed (>25)The indicators blink once.≥When changing the setting (“To reduce the clear-mode dialog effect” and “To turn off the volume limitation”) (>25)Bluetooth® indicator blinks quickly.≥When the main unit is ready for pairingBluetooth® indicator blinks slowly.≥When the main unit is waiting to connectBluetooth® indicator turns on.≥When the main unit is connected with a Bluetooth® deviceSC-HTB350_RQT9670_mst.book Page 28 Tuesday, December 20, 2011 2:05 PM
ReferenceRQT9670 29SpecificationsAMPLIFIER SECTIONRMS output power10 % total harmonic distortionSubwoofer ch120 W per channel (100 Hz, 8 ≠)Front ch (L, R ch)60 W per channel (1 kHz, 6 ≠)Total RMS Dolby Digital mode power 240 WFTC output power1.0 % total harmonic distortionSubwoofer ch60 Hz to 120 Hz 40 W (8 ≠)Front ch (L, R ch)120 Hz to 20 kHz 25 W (6 ≠)Total FTC Dolby Digital mode power90 WWIRELESS SECTIONWireless moduleFrequency Range 5.150 GHz to 5.250 GHz5.725 GHz to 5.850 GHzNumber of channels 9TERMINAL SECTIONDigital audio inputOptical digital input (TV, BD/DVD) 2Sampling frequency32 kHz, 44.1 kHz, 48 kHz88.2 kHz, 96 kHz (only LPCM)Audio formatLPCM, Dolby Digital, DTSSPEAKER SECTIONFront speakers2 way, 2 speaker system (Bass reflex type)Speaker unit(s) Impedance 6≠Woofer6.5 cm (2 1/2q)conetypek1Tweeter2.5 cm (1q) semi-dome typek1Frequency range100 Hz to 30 kHz (j16 dB)150 Hz to 25 kHz (j10 dB)Active subwoofer1 way, 1 speaker system (Bass reflex type)Woofer 16 cm (6 1/2q)conetypek1Frequency range 30 Hz to 180 Hz (j16 dB)35 Hz to 160 Hz (j10 dB)GENERALPower consumption Main unit: 25 WActive subwoofer: 21 WIn standby conditionMain unit: Approx. 0.1 WActive subwoofer: Approx. 0.1 WPower supply AC 120 V, 60 HzDimensions (WkHkD)Main unitCabinet dimension310 mmk44 mmk195 mm(12 7/32qk123/32qk711/16q)Maximum outer dimension310 mmk45 mmk202 mm(12 7/32qk125/32qk715/16q)Active subwoofer180 mmk408 mmk306 mm(7 3/32qk16 1/16qk12 1/16q)Mass (Weight)Main unit 1.1 kg(2.4 lbs)Active subwoofer 5.2 kg(11.47 lbs)Operating temperature range0oC to _40 oC (_32 oF to _104 oF)Operating humidity range20 % to 80 % RH (no condensation)SC-HTB350_RQT9670_mst.book Page 29 Tuesday, December 20, 2011 2:05 PM
30 RQT96701 Specifications are subject to change without notice.2 Weight and dimensions are approximate.3 Total harmonic distortion is measured by a digital spectrum analyzer.SPEAKER GENERALHorizontal placement using the standsDimensions (WkHkD)956 mmk102 mmk74 mm(37 5/8qk41/32qk229/32q)Mass (Weight) 1.61 kg(3.7 lbs)Horizontal placement using the speaker feet and the support legsDimensions (WkHkD)956 mmk78 mmk55 mm(37 5/8qk31/16qk25/32q)Mass (Weight) 1.57 kg(3.5 lbs)Horizontal placement (for wall mount)Dimensions (WkHkD)956 mmk75 mmk35 mm(37 5/8qk215/16qk13/8q)Mass (Weight) 1.54 kg(3.5 lbs)Vertical placement using the speaker basesDimensions (WkHkD)148 mmk528 mmk145 mm(5 13/16qk20 25/32qk523/32q)Mass (Weight) 0.88 kg(1.98 lbs)Vertical placement (for wall mount)Dimensions (WkHkD)75 mmk478 mmk35 mm(2 15/16qk18 13/16qk13/8q)Mass (Weight) 0.77 kg(1.76 lbs)Bluetooth® SECTIONBluetooth® system specificationV2.1 + EDRWireless equipment classificationClass 2 (2.5 mW)Supported profiles A2DP, AVRCPFrequency band2402 MHz to 2480 MHz(Adaptive Frequency Hopping)Operating distance10 m (33 ft) Line of SightSC-HTB350_RQT9670_mst.book Page 30 Tuesday, December 20, 2011 2:05 PM
ReferenceRQT9670 31Limited Warranty (ONLY FOR U.S.A. AND PUERTO RICO)Panasonic Consumer Marketing Company of North America, Division of Panasonic Corporation of North AmericaOne Panasonic Way, Secaucus, New Jersey 07094Panasonic Home Audio Products Limited WarrantyLimited Warranty Coverage(For USA and Puerto Rico Only)If your product does not work properly because of a defect in materials or workmanship, Panasonic Consumer Marketing Company of North America (referred to as “the warrantor”) will, for the length of the period indicated on the chart below, which starts with the date of original purchase (“warranty period”), at its option either (a) repair your product with new or refurbished parts, (b) replace it with a new or a refurbished equivalent value product, or (c) refund your purchase price. The decision to repair, replace or refund will be made by the warrantor.During the “Labor” warranty period there will be no charge for labor. During the “Parts” warranty period, there will be no charge for parts. This Limited Warranty excludes both parts and labor for non-rechargeable batteries, antennas, and cosmetic parts (cabinet). This warranty only applies to products purchased and serviced in the United States or Puerto Rico. This warranty is extended only to the original purchaser of a new product which was not sold “as is”.Carry-In or Mail-In ServiceTo find a service center please visit http://www.panasonic.com/help or call 1-800-211-PANA (7262).When shipping the unit, carefully pack, include all supplied accessories listed in the Owner’s Manual, and send it prepaid, adequately insured and packed well in a carton box. When shipping Lithium Ion batteries please visit our Web Site at www.panasonic.com/BatteryHandling as Panasonic is committed to providing the most up to date information. Include a letter detailing the complaint, a return address and provide a daytime phone number where you can be reached. A valid registered receipt is required under the Limited Warranty.IF REPAIR IS NEEDED DURING THE WARRANTY PERIOD, THE PURCHASER WILL BE REQUIRED TO FURNISH A SALES RECEIPT/PROOF OF PURCHASE INDICATING DATE OF PURCHASE, AMOUNT PAID AND PLACE OF PURCHASE. CUSTOMER WILL BE CHARGED FOR THE REPAIR OF ANY UNIT RECEIVED WITHOUT SUCH PROOF OF PURCHASE.Limited Warranty Limits And ExclusionsThis warranty ONLY COVERS failures due to defects in materials or workmanship, and DOES NOT COVER normal wear and tear or cosmetic damage. The warranty ALSO DOES NOT COVER damages which occurred in shipment, or failures which are caused by products not supplied by the warrantor, or failures which result from accidents, misuse, abuse, neglect, mishandling, misapplication, alteration, faulty installation, set-up adjustments, misadjustment of consumer controls, improper maintenance, power line surge, lightning damage, modification, introduction of sand, humidity or liquids, commercial use such as hotel, office, restaurant, or other business or rental use of the product, or service by anyone other than a Factory Service Center or other Authorized Servicer, or damage that is attributable to acts of God.THERE ARE NO EXPRESS WARRANTIES EXCEPT AS LISTED UNDER “LIMITED WARRANTY COVERAGE”.THE WARRANTOR IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE USE OF THIS PRODUCT, OR ARISING OUT OF ANY BREACH OF THIS WARRANTY. (As examples, this excludes damages for lost time, travel to and from the servicer, loss of or damage to media or images, data or other memory or recorded content. The items listed are not exclusive, but for illustration only.)ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTY OF MERCHANTABILITY, ARE LIMITED TO THE PERIOD OF THE LIMITED WARRANTY.Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the exclusions may not apply to you.This warranty gives you specific legal rights and you may also have other rights which vary from state to state. If a problem with this product develops during or after the warranty period, you may contact your dealer or Service Center. If the problem is not handled to your satisfaction, then write to the warrantor’s Consumer Affairs Department at the addresses listed for the warrantor.PARTS AND SERVICE, WHICH ARE NOT COVERED BY THIS LIMITED WARRANTY, ARE YOUR RESPONSIBILITY.As of January 2012Product or Part Name Parts LaborAudio Products(except items below)1 year 1 yearDVD Home Theater System 1 year 1 yearHome Theater Audio System 1 year 1 yearSD Memory Cards, Rechargeable Battery Packs (defective exchange)90 days NotApplicableCustomer Services Directory (United States and Puerto Rico)Obtain Product Information and Operating Assistance; locate your nearest Dealer or Service Center; purchase Parts and Accessories; or make Customer Service and Literature requests by visiting our Web Site at:http://www.panasonic.com/helpor, contact us via the web at:http://www.panasonic.com/contactinfoYou may also contact us directly at:1-800-211-PANA (7262)Monday-Friday 9am-9pm, Saturday-Sunday 10am-7pm ESTFor hearing or speech impaired TTY users, TTY: 1-877-833-8855 Accessory Purchases (United States and Puerto Rico)Purchase Parts, Accessories and Instruction Books online for all Panasonic Products by visiting our Web Site at:http://www.pstc.panasonic.comOr, send your request by E-mail to:npcparts@us.panasonic.comYou may also contact us directly at:1-800-332-5368 (Phone) 1-800-237-9080 (Fax Only)(Monday-Friday 9am-9pm EST)Panasonic National Parts Center20421 84th Ave S., Kent, WA 98032(We accept Visa, MasterCard, Discover Card, American Express)For hearing or speech impaired TTY users, TTY: 1-866-605-1277 The model number and serial number of this product can be found on either the back or the bottom of the unit.Please note them in the space provided below and keep for future reference.MODEL NUMBER SC-HTB350SERIAL NUMBERUser memo:DATE OF PURCHASE ______________________________DEALER NAME ___________________________________DEALER ADDRESS_________________________________________________________________________________TELEPHONE NUMBER _____________________________SC-HTB350_RQT9670_mst.book Page 31 Tuesday, December 20, 2011 2:05 PM
Panasonic Corporation 2011Printed in MalaysiaOne Panasonic Way, Secaucus, New Jersey 07094http://www.panasonic.comPanasonic Consumer Marketing Company of North America, Division of Panasonic Corporation of North AmericaRQT9670-PF1211RK0-If you see this symbol- Unit care∫Clean the system with a soft, dry cloth≥When dirt is heavy, wring a cloth moistened in water tightly to wipe the dirt, and then wipe it with a dry cloth.≥When cleaning the system, use a fine cloth. Do not use tissues or other materials (towels, etc.) that can fall apart. Small grains may get stuck inside the speaker cover.≥Never use alcohol, paint thinner or benzine to clean the system.≥Before using chemically-treated cloth, carefully read the instructions that came with the cloth.Information on Disposal in other Countries outside the European UnionThis symbol is only valid in the European Union.If you wish to discard this product, please contact your local authorities or dealer and ask for the correct method of disposal.As an ENERGY STAR Partner, Panasonic has determined thatthis product meets the ENERGY STAR guidelines for energy efficiency.®®Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending.DTS, the Symbol, & DTS and the Symbol together are registered trademarks & DTS Digital Surround and the DTS logos are trademarks of DTS, Inc. Product includes software.© DTS, Inc. All Rights Reserved.The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Panasonic Corporation is under license. Other trademarks and trade names are those of their respective owners.SC-HTB350_RQT9670_mst.book Page 32 Tuesday, December 20, 2011 2:05 PM

Navigation menu