Panasonic Devices Europe 1760 Bluetooth Smart Module User Manual TABLE OF CONTENTS

Panasonic Industrial Devices Europe GmbH Bluetooth Smart Module TABLE OF CONTENTS

15_PAN1760_UserMan

CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 1 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 Power Electronics R&D Center Wireless Connectivity Panasonic Industrial Devices Europe GmbH APPROVED genehmigt CHECKED geprüft DESIGNED erstellt Product Specification Applicant / Manufacturer Hardware Panasonic Industrial Devices Europe GmbH Zeppelinstrasse 19 21337 Lüneburg Germany Applicant / Manufacturer Software Toshiba Software Version Please refer to chapter 21 By purchase of any of products described in this document the customer accepts the document's validity and declares their agreement and understanding of its contents and recommendations. Panasonic reserves the right to make changes as required without notification.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 2 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de TABLE OF CONTENTS 1. Scope of this Document ................................................................................................ 4 2. Key Features ................................................................................................................. 4 3. Bluetooth Low Energy ................................................................................................... 5 4. Applications for the Module ........................................................................................... 5 5. Description for the Module ............................................................................................. 5 6. Detailed Description ...................................................................................................... 6 6.1. PAN1760 Terminal Layout ................................................................................... 6 7. PAN1760 Block Diagram ............................................................................................... 8 8. GPIO Function List ........................................................................................................ 9 9. Test Conditions ........................................................................................................... 10 10. General Device Requirements and Operation ............................................................. 10 10.1. Absolute Maximum Ratings ................................................................................ 10 10.2. Recommended Operating Conditions ................................................................. 10 10.3. Power up sequence ........................................................................................... 11 10.4. PAN1760 Current Consumption ......................................................................... 11 11. Bluetooth RF Performance .......................................................................................... 12 11.1. PAN1760 Bluetooth Characteristics ................................................................... 12 11.2. PAN1760 Spurious Emission ............................................................................. 12 12. Soldering Temperature-Time Profile (for reflow soldering) ........................................... 13 12.1. For lead solder ................................................................................................... 13 12.2. For leadfree solder ............................................................................................. 13 13. PAN1760 Module Dimension ...................................................................................... 14 14. PAN1760 Footprint of the Module ............................................................................... 15 15. Case Marking .............................................................................................................. 16 15.1. Example for Marking .......................................................................................... 16 15.2. Marking Definition .............................................................................................. 16 16. Mechanical Requirements ........................................................................................... 16 17. Development of Applications ....................................................................................... 17 18. Reliability Tests ........................................................................................................... 17 19. Cautions ...................................................................................................................... 17 19.1. Design Notes ..................................................................................................... 17 19.2. Installation Notes ................................................................................................ 18 19.3. Usage Conditions Notes ..................................................................................... 18 19.4. Storage Notes .................................................................................................... 19 19.5. Safety Cautions .................................................................................................. 19 19.6. Other cautions .................................................................................................... 19 20. Packaging ................................................................................................................... 21 20.1. PAN1760 Tape Dimension ................................................................................. 21 20.2. Packing in Tape ................................................................................................. 22
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 3 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 20.3. Component Direction ......................................................................................... 22 20.4. Reel Dimension .................................................................................................. 23 20.5. Label for Package .............................................................................................. 24 20.6. Total Package .................................................................................................... 24 21. Ordering Information ................................................................................................... 25 22. RoHS and REACH Declaration ................................................................................... 26 23. Data Sheet Status ....................................................................................................... 27 24. History for this Document ............................................................................................ 27 25. Related Documents ..................................................................................................... 27 26. Radiation Pattern of Antenna ...................................................................................... 28 27. General Information ..................................................................................................... 30 28. Regulatory Information ................................................................................................ 30 28.1. FCC Notice ........................................................................................................ 30 28.2. Caution .............................................................................................................. 30 28.3. Labeling Requirements ...................................................................................... 31 28.4. Antenna Warning ............................................................................................... 31 28.5. Approved Antenna List ....................................................................................... 31 28.6. RF Exposure PAN1760 ...................................................................................... 31 29. Industry Canada Certification ...................................................................................... 32 29.1. IC Notice ............................................................................................................ 32 29.2. Labeling Requirements ...................................................................................... 32 30. Bluetooth Certification ................................................................................................. 32 31. European R&TTE Declaration of Conformity ............................................................... 33 32. Life Support Policy ...................................................................................................... 33
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 4 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 1. SCOPE OF THIS DOCUMENT This product specification applies to Panasonic’s, Class 2, Bluetooth®1 low energy single mode module, series number: PAN1760 2. KEY FEATURES  Same form factor and footprint as PAN1026  Bluetooth 4.0 (LE) embedded GATT profile with high level API commands, compatible to Toshiba reference BLE profiles  Surface mount type 15.6 x 8.7 x 1.8 mm³  Tx power 0 dBm, Rx sensitivity -91 dBm  Compliant to BT 4.0 (extension to 4.1 under development)  32kB on-chip RAM for application software and driver  512kBit eeprom to download user program during start up  Operation with external host or as host-less ( stand alone)  Standard SIG BLE and “SPP over BLE” profiles available  Temperature Range from -40°C to +85°C  2 UART, I2C , SPI, GPIO (10 in/out), Wake-Up control pins, ADC(4 CH) 1 Bluetooth is a registered trademark of the Bluetooth Special Interest Group.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 5 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 3. BLUETOOTH LOW ENERGY Bluetooth Low Energy (BLE), part of Bluetooth Ver. 4.0, specifies two types of implementation: Single mode and dual mode. Single mode devices implement the low energy specification and consume just a fraction of the power of classic Bluetooth, allowing the short-range wireless standard to extend to coin cell battery applications for the first time. Dual mode devices combine Bluetooth Low Energy and classic Bluetooth and are likely to become a de facto feature in almost all new Bluetooth enabled cellular phones and computers. Single mode Bluetooth 4.0 Low Energy is not backwards compatible with previous Bluetooth classic standards. Dual mode Bluetooth 4.0 is backwards compatible to Bluetooth classic and well suited for gateway applications, but is not practical for low power devices. BLE single mode devices are called “Bluetooth Smart”. 4. APPLICATIONS FOR THE MODULE  All Embedded Wireless Applications  Wearable Devices  Health Care, Medical Diagnostic Systems  Mobile phone accessories  Industrial Measurement and Diagnostics  Devices where Power Consumption is critical 5. DESCRIPTION FOR THE MODULE The PAN1760 is a short-range, Class 2, BLE single mode module for implementing Bluetooth functionality into various electronic devices. A block diagram can be found in chapter 7. The PAN1760 is a cost-effective, low-power, true system-on-chip (SoC) for Bluetooth low energy applications. It enables robust BLE central and peripheral nodes to be built with very low total bill-of-material costs. The PAN1760 combines an excellent RF transceiver programmable EEPROM memory, 32-KB RAM, and many other powerful supporting features and peripherals. The PAN1760 is suitable for systems where very low power consumption is required. Very low-power sleep modes are available. Short transition times between operating modes further enable low power consumption. Panasonic PAN1760 offers an embedded and certified Bluetooth low energy protocol stack and BLE GATT profile inside the silicon device from Toshiba. The Bluetooth low energy protocol stack from Toshiba, is a flexible and cost-effective single-mode Bluetooth low energy solution. Standard BLE or proprietary profiles are available for seamless integration into the application code Please contact your local sales office for further details on additional options and services: www.panasonic.com/rfmodules for the US, http://industrial.panasonic.com/eu/i/29606/wireless_modules/wireless_modules.html for EU or write an e-mail to wireless@eu.panasonic.com.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 6 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 6. DETAILED DESCRIPTION 6.1. PAN1760 TERMINAL LAYOUT Top View, Application PCB F2 F3 F4 F5E1 E2 E3 E4 E5 E6 E7 E8 E9D1 D2 D3 D4 D5 D6 D7 D8C1 C2 C3 C4 C5 C6 C7 C8B1 B2 B3 B4 B5 B6 B7 B8 B9A2 A3 A4 A5 A6 A7 A8A11.08.70 mm0.65.00.61.35 1.351.2F91.2F7F1 F8D9C9A915.6 mmF6 F11A11F12A122.4
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 7 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de No Pin Name Pin Type Description A1 GND Ground Pin Connect to Ground A2 NC Not Connected A3 Reset Digital Input Reset, active-low A4 VCC Power 2V – 3.6V analog/digital power supply connection A5 VCC Power 2V – 3.6V analog/digital power supply connection A6 VCC Power 2V – 3.6V analog/digital power supply connection A7 GND Ground Pin Connect to Ground A8 NC Not Connected A9 GND Ground Pin Connect to Ground A11 GND Ground Pin Connect to Ground A12 GND Ground Pin Connect to Ground B1 NC Not Connected B2 GPIO14 Digital I/O B3 GPIO11 Digital I/O B4 NC Not Connected B5 NC Not Connected B6 NC Not Connected B7 NC Not Connected B8 NC Not Connected B9 NC Not Connected C1 NC Not Connected C2 GPIO15 Digital I/O C3 GPIO12 Digital I/O C4 NC Not Connected C5 NC Not Connected C6 GPIO9 Digital I/O C7 GPIO10 Digital I/O C8 GND Ground Pin Connect to Ground C9 GND Ground Pin Connect to Ground D1 NC Not Connected D2 NC Not Connected D3 GPIO1 Digital I/O D4 GPIO0 Digital I/O D5 NC Not Connected D6 GPIO13 Digital I/O D7 GND Ground Pin Connect to Ground D8 GND Ground Pin Connect to Ground D9 NC PAN1760 Not Connected/Placeholder for Antenna E1 SDA Digital I/O Connected to internal EEPROM E2 SCL Digital I/O Connected to internal EEPROM E3 NC Not Connected E4 NC Not Connected E5 SLPXOIN Clock In 32.768 KHz sleep clock input E6 UART_RXD Digital In E7 GPIO2 Digital I/O E8 GND Ground Pin Connect to Ground E9 GND Ground Pin Connect to Ground F1 GND Ground Pin Connect to Ground F2 EEPROM_WP Digital In EEPROM write protect /active low F3 NC Not Connected F4 NC Not Connected F5 UART_CTS Digital In Can be configured to UART2_RXD F6 SLPXOOUT Clock Out 32.768 KHz sleep clock output F7 UART_TXD Digital Out F8 UART_RTS Digital I/O Can be configured to UART2_TXD F9 GND Ground Pin Connect to Ground F11 GND Ground Pin Connect to Ground F12 GND Ground Pin Connect to Ground
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 8 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 7. PAN1760 BLOCK DIAGRAM PAN1760T o s h ib aS in g le M o d e B lu e to o th L S ITC35667E E P R O MC ry s ta l 26 M H zF ilte rV C C /VSSS lo w C lo c k 32.768 k H zU A R TG P IOW a ke U p In p u tW a ke U p O u tp u tI2 C A n te n n a RF Block26MHzX’talFilterClockGen/Clock ManagementRF PLL Power　ManagementController32kHzSiOSCVDD1.8～3.6V1.2VTC35667Baseband BlockUART2chHOST I/FSPI/I2C PWM外部メモリ I/FGPIO ADC4chModem ARM7　TDMI-STMMaskROMRAM(BackUp)Selector1.5V1.2VRef VDD32kHzX’talLevelDetectorLDODCDCExternal memory External
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 9 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 8. GPIO FUNCTION LIST GPIO pins are assigned to UART or serial memory. About the details refer to firmware specification. Pin Analog input Function 1 Function 2 Function 3 Function 4 Function 5 GPIO0 - GPIO1 Digital I/O WakeUp Input - - - GPIO1 ADC0 Input GPIO Digital I/O - - - - GPIO2 ADC1 Input GPIO Digital I/O PWM0 Output - - - GPIO3_TEST - GPIO Digital I/O UART1-TX Output - SPI-DOUT Output UART2-TX Output GPIO4 - GPIO Digital I/O UART1-RX Input - SPI-DIN Input UART2-RX Input GPIO5_Bmode - GPIO Digital I/O UART1-RTSX Output UART2-TX Output SPI-SCS Output UART1-TX Output GPIO6 - GPIO Digital I/O UART1-CTSX Input UART2-RX Input SPI-SCLK Output UART1-RX Input GPIO7 - GPIO Digital I/O - I2C-SCL Output SPI-DOUT Output - GPIO8 - GPIO Digital I/O - I2C-SDA I/O SPI-DIN Input - GPIO9 - GPIO Digital I/O PWM1 Output I2C-SCL Output - - GPIO10 - GPIO Digital I/O PWM2 Output I2C-SDA I/O - - GPIO11～14 - GPIO Digital I/O - - - - GPIO15 ADC2 Input GPIO Digital I/O - - - - Pin name Basic example Example of UART1 + UART2 + I2C Example of SPI + I2C Example of UART + SPI + I2C GPIO0 Wake Up Wake Up Wake Up Wake Up GPIO1 ADC- AIN0 ADC- AIN0 ADC- AIN0 ADC- AIN0 GPIO2 ADC-AIN1 / PWM0 ADC-AIN1 / PWM0 ADC-AIN1 / PWM0 ADC-AIN1 / PWM0 GPIO3 UART1-TX UART1-TX SPI-DOUT UART1-TX GPIO4 UART1-RX UART1-RX SPI-DIN UART1-RX GPIO5 UART1-RTSX UART2-TX SPI-SCS SPI-SCS GPIO6 UART1-CTSX UART2-RX SPI-SCLK SPI-SCLK GPIO7 I2C-SCL I2C-SCL I2C-SCL SPI-DOUT GPIO8 I2C-SDA I2C-SDA I2C-SDA SPI-DIN GPIO9 PWM1 PWM1 PWM1 I2C-SCL GPIO10 PWM2 PWM2 PWM2 I2C-SDA GPIO11-14 - - - - GPIO15 ADC-AIN2 ADC-AIN2 ADC-AIN2 ADC-AIN2
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 10 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 9. Test Conditions Measurements shall be made under operating free-air temperature range unless otherwise specified. Temperature 25 ± 10°C Humidity 40 to 85%RH Supply Voltage 3.3V 10. GENERAL DEVICE REQUIREMENTS AND OPERATION All specifications are over temperature and process, unless indicated otherwise. 10.1. ABSOLUTE MAXIMUM RATINGS No See 2 Value Unit Ratings Over Operating Free-Air Temperature Range 1 Voltage on any digital pin –0.3 to VDD+0.3 V 2 Operating ambient temperature range –40 to 85 °C 3 Storage temperature range –40 to 125 °C 4 Bluetooth RF inputs 10 dBm 5 ESD: All pads, according to human-body model, JEDEC STD 22, method A114 According to charged-device model, JEDEC STD 22, method C101 1000 500 V 10.2. RECOMMENDED OPERATING CONDITIONS No Rating Min Typ Max Unit 1 Power supply voltage 1.7 1.8 1.9 V 1 Power supply voltage 2.7 3.3 3.6 V 2 Maximum ambient operating temperature -40 85 C 2 Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only and functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 11 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 10.3. POWER UP SEQUENCE When the power is turned on, set reset signal to low (RESET=Low). After OSC is stable, release reset (RESET=High). Crystal oscillator stabilizing time is about 2 msec, so define release time after sufficient evaluation. When the power is turned off, set reset signal to low (RESET=Low). 10.4. PAN1760 CURRENT CONSUMPTION The current consumption is dependent on the user scenario and the setup and timing in the low power modes. The total power consumption can be optimized by adjusting advertising and connectionintervals. It also depends on the system configuration of the central device (typically mobile phone or BLE hub). VDD power supply Reset signal DCDC / LDO output Power off OSC boot timer Operation Power on voltage detection RC delay Reference clock Stable Unstable
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 12 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 11. BLUETOOTH RF PERFORMANCE 11.1. PAN1760 BLUETOOTH CHARACTERISTICS No Characteristics Condition Min Typ Max Unit 1 Operation frequency range 2402 2480 MHz 2 Channel spacing 2 MHz 3 Output Power Maximum setting, measured at single ended 50ohm. 0 dBm 4 Sensitivity, High Gain Mode High-gain mode -93.0 dBm 11.2. PAN1760 SPURIOUS EMISSION No Characteristics Condition Typ Max Unit 1 Spurious emissions Conducted measurement with a 50-Ω single-ended load. Complies with EN 300 328, EN 300 440 class 2, FCC CFR47, Part 15 and ARIB STD-T-66 -41 dBm
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 13 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 12. SOLDERING TEMPERATURE-TIME PROFILE (FOR REFLOW SOLDERING) 12.1. FOR LEAD SOLDER Recommended temp. profile for reflow soldering Temp.[°C] Time [s] 235°C max. 220 5°C 200°C 150 10°C 90 30s 10 1s 30 +20/-10s 12.2. FOR LEADFREE SOLDER Our used temp. profile for reflow soldering Temp.[°C] Time [s] 230°C -250°C max. 220°C 150°C – 190°C 90 30s 30 +20/-10s Reflow permissible cycle: 2 Opposite side reflow is prohibited due to module weight.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 14 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 13. PAN1760 MODULE DIMENSION No. Item Dimension Tolerance Remark 1 Width 8.70  0.30 2 Length 15.60  0.30 3 Height 1.80  0.20 With case
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 15 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 14. PAN1760 FOOTPRINT OF THE MODULE All dimensions are in millimeters. The outer dimensions have a tolerance of  0.3mm. Top view, Application PCB F2 F3 F4 F5E1 E2 E3 E4 E5 E6 E7 E8 E9D1 D2 D3 D4 D5 D6 D7 D8C1 C2 C3 C4 C5 C6 C7 C8B1 B2 B3 B4 B5 B6 B7 B8 B9A2 A3 A4 A5 A6 A7 A8A11.08.70 mm0.65.00.61.35 1.351.2F91.2F7F1 F8D9C9A915.6 mmF6 F11A11F12A122.4
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 16 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 15. CASE MARKING 123 15.1. EXAMPLE FOR MARKING 15.2. MARKING DEFINITION (1) Pin1 marking (2) 2D code (Serial number) (3) Marking:  PAN1760 (Model Name), HW/SW (Hardware/Software version)  ENW89847A1KF (Part Number, refer to chapter 21 Ordering Information)  Lot code (YearYear, WeekWeek, Day, LotLot)  ES (Engineering Sample marking) Note: For available Software Versions, refer to [1] PAN1760ETU Design-Guide. and chapter 21 Ordering Information. 16. MECHANICAL REQUIREMENTS No. Item Limit Condition 1 Solderability More than 75% of the soldering area shall be coated by solder Reflow soldering with recommendable temperature profile 2 Resistance to soldering heat It shall be satisfied electrical requirements and not be mechanical damage See chapter 12.2 No. Remark 1 Marking for Pin 1 (Circle 0,15 mm) 2 2D-Code, for internal usage only and can be change without any notice 3 Marking definition see below P A N 1 7 6 0 H W / S WE N W 8 9 8 4 7 A x K FY Y W W D L LF C C I D : T 7 V 1 7 6 0
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 17 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 17. DEVELOPMENT OF APPLICATIONS For development support please refer to [1] PAN1760ETU Design-Guide. 18. RELIABILITY TESTS The measurement should be done after being exposed to room temperature and humidity for 1 hour. No. Item Limit Condition 1 Vibration test Electrical parameter should be in specification a) Freq.:10~50Hz,Amplitude:1.5mm a) 20min. / cycle,1hrs. each of XYZ axis b) Freq.:30~100Hz, 6G b) 20min. / cycle,1hrs. each of XYZ axis 2 Shock test the same as above Dropped onto hard wood from height of 50cm for 3 times 3 Heat cycle test the same as above -40°C for 30min. and +85°C for 30min.; each temperature 300 cycles 4 Moisture test the same as above +60°C, 90% RH, 300h 5 Low temp. test the same as above -40°C, 300h 6 High temp. test the same as above +85°C, 300h 19. CAUTIONS Failure to follow the guidelines set forth in this document may result in degrading of the product’s functions and damage to the product. 19.1. DESIGN NOTES (1) Follow the conditions written in this specification, especially the control signals of this module. (2) The supply voltage has to be free of AC ripple voltage (for example from a battery or a low noise regulator output). For noisy supply voltages, provide a decoupling circuit (for example a ferrite in series connection and a bypass capacitor to ground of at least 47uF directly at the module). (3) This product should not be mechanically stressed when installed. (4) Keep this product away from heat. Heat is the major cause of decreasing the life of these products. (5) Avoid assembly and use of the target equipment in conditions where the products' temperature may exceed the maximum tolerance. (6) The supply voltage should not be exceedingly high or reversed. It should not carry noise and/or spikes. (7) Keep this product away from other high frequency circuits.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 18 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 19.2. INSTALLATION NOTES (1) Reflow soldering is possible twice based on the conditions in chapter 15. Set up the temperature at the soldering portion of this product according to this reflow profile. (2) Carefully position the products so that their heat will not burn into printed circuit boards or affect the other components that are susceptible to heat. (3) Carefully locate these products so that their temperatures will not increase due to the effects of heat generated by neighboring components. (4) If a vinyl-covered wire comes into contact with the products, then the cover will melt and generate toxic gas, damaging the insulation. Never allow contact between the cover and these products to occur. (5) This product should not be mechanically stressed or vibrated when reflowed. (6) To repair the board by hand soldering, follow the conditions set forth in this chapter. (7) Do not wash this product. (8) Refer to the recommended pattern when designing a board. (9) Pressing on parts of the metal cover or fastening objects to the metal will cause damage to the unit. (10) For more details on LGA (Land Grid Arrey) soldering processes refer to the application note. 19.3. USAGE CONDITIONS NOTES (1) Take measures to protect the unit against static electricity. If pulses or other transient loads (a large load applied in a short time) are applied to the products, check and evaluate their operation befor assembly on the final products. (2) Do not use dropped products. (3) Do not touch, damage or soil the pins. (4) Follow the recommended condition ratings about the power supply applied to this product. (5) Electrode peeling strength: Do not add pressure of more than 4.9N when soldered on PCB. (6) Pressing on parts of the metal cover or fastening objects to the metal cover will cause damage. (7) These products are intended for general purpose and standard use in general electronic equipment, such as home appliances, office equipment, information and communication equipment.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 19 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 19.4. STORAGE NOTES (1) The module should not be stressed mechanically during storage. (2) Do not store these products in the following conditions or the performance characteristics of the product, such as RF performance will be adversely affected:  Storage in salty air or in an environment with a high concentration of corrosive gas, such as Cl2, H2S, NH3, SO2, or NOX  Storage in direct sunlight  Storage in an environment where the temperature may be outside the range of 5°C to 35°C range, or where the humidity may be outside the 45 to 85% range.  Storage of the products for more than one year after the date of delivery Storage period: Please check the adhesive strength of the embossed tape and soldering after 6 months of storage. (3) Keep this product away from water, poisonous gas and corrosive gas. (4) This product should not be stressed or shocked when transported. (5) Follow the specification when stacking packed crates (max. 10). 19.5. SAFETY CAUTIONS These specifications are intended to preserve the quality assurance of products and individual components. Before use, check and evaluate the operation when mounted on your products. Abide by these specifications, without deviation when using the products. These products may short-circuit. If electrical shocks, smoke, fire, and/or accidents involving human life are anticipated when a short circuit occurs, then provide the following failsafe functions, as a minimum. (1) Ensure the safety of the whole system by installing a protection circuit and a protection device. (2) Ensure the safety of the whole system by installing a redundant circuit or another system to prevent a single fault causing an unsafe status. 19.6. OTHER CAUTIONS (1) This specification sheet is copyrighted. Please do not disclose it to a third party. (2) Please do not use the products for other purposes than those listed. (3) Be sure to provide an appropriate fail-safe function on your product to prevent an additional damage that may be caused by the abnormal function or the failure of the product. (4) This product has been manufactured without any ozone chemical controlled under the Montreal Protocol. (5) These products are not intended for other uses, other than under the special conditions shown below. Before using these products under such special conditions, check their performance and reliability under the said special conditions carefully to determine whether or not they can be used in such a manner.  In liquid, such as water, salt water, oil, alkali, or organic solvent, or in places where liquid may splash.  In direct sunlight, outdoors, or in a dusty environment  In an environment where condensation occurs.  In an environment with a high concentration of harmful gas (e.g. salty air, HCl,
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 20 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de Cl2, SO2, H2S, NH3, and NOX) (6) If an abnormal voltage is applied due to a problem occurring in other components or circuits, replace these products with new products because they may not be able to provide normal performance even if their electronic characteristics and appearances appear satisfactory. (7) When you have any question or uncertainty, contact Panasonic.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 21 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 20. PACKAGING If the product has mass production status, indicated in chapter 23, we will deliver the module in the package which are described below. 20.1. PAN1760 TAPE DIMENSION
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 22 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 20.2. PACKING IN TAPE 100730-PAN1720.vsdtrailer (empty)1 x circumference /hub(min 160mm)component packed areastandard 1500pcsleader (empty)minimum 10 pitchTop cover tape more than 1 x circumference plus 100mm to avoid fixing of tape end on sealed modules.Direction of unreeling (for customer) Empty spaces in component packed area shall be less than two per reel and those spaces shall not be consecutive. Top cover tape shall not be found on reel holes and shall not stick out from reel. 20.3. COMPONENT DIRECTION 100730-PAN1720.vsdDirection of unreeling(for customer)Pin 1 Marking(Top Side)Pin 1 Marking(Bottom Side)Square Pin, all the others are round.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 23 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 20.4. REEL DIMENSION
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 24 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 20.5. LABEL FOR PACKAGE The picture shows an example from similar product. PAN1315Customer Code ENW89818C2JF105 mm51 mm (1T) Lot code [YYWWDLL] Example from above: YY year printed 08 WW normal calendar week printed 01 D day printed 5 (Friday) L line identifier, if more as one printed 1 L lot identifier per day printed 1 (1P) Customer Order Code, if any, otherwise company name will be printed (2P) Panasonic Order Code: ENW89847A1KF (9D) Date code as [YYWW] (Q) Quantity [XXXX], variable max. 1500 (HW/SW) Hardware /Software Release Hardware 01 Indicates the HW revision. Software 01 Indicates the SW revision. 20.6. TOTAL PACKAGE barcodelabelmoisture-sensitive print(already exist on barrier bag) barcodelabeldesiccant 1) 2)moisture indicatorbarrier bagsealedinner carton boxsize 340 x 340 x 41 mm³1) quantity of desiccant according to calculation2) optional: desiccant placed into the corner of the barrier bag
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 25 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 21. ORDERING INFORMATION Ordering part number Description MOQ (1) ENW89847A1KF (2) PAN1760 CLASS 2 Bluetooth single mode Module according BT-4.0. Bluetooth® smart device 1500 Notes: (1) Abbreviation for Minimum Order Quantity (MOQ). The standard MOQ for mass production is 1500 pieces, fewer only on customer demand. Samples for evaluation can be delivered at any quantity via the distribution channels. (2) Samples are available on customer demand
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 26 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 22. ROHS AND REACH DECLARATION Hereby we declare to our best present knowledge based on declaration of our suppliers that this product follows th elatest official RoHS and REACH Directive. For the most updated one, please refer to [3].
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 27 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 23. DATA SHEET STATUS This data sheet contains the preliminary specification. Panasonic reserves the right to make changes at any time without notice in order to improve design and supply the best possible product. Please consult the most recently issued data sheet before initiating or completing a design. 24. HISTORY FOR THIS DOCUMENT Revision Date Modification / Remarks 0.1 January 2015 1st preliminary version. 25. RELATED DOCUMENTS For an update, please search in the suitable homepage. [1] PAN1760ETU Design-Guide http://www.pideu.panasonic.de [2] Application Note Land Grid Array http://www.pideu.panasonic.de/pdf/184ext.pdf [3] REACH and RoHS Certificate http://www.pideu.panasonic.de/pdf/182ext2.jpg SOLLTE MAN HIER NOCH EINEN HINWEIS AUF TC35667FTG Dokumente einfügen ? (URL link)
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 28 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 26. RADIATION PATTERN OF ANTENNA
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 29 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 30 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 27. GENERAL INFORMATION © Panasonic Industrial Devices Europe GmbH 2012. All rights reserved. This product description does not lodge the claim to be complete and free of mistakes. Please contact the related product manager in every case. If we deliver ES samples to the customer, these samples have the status Engineering Samples. This means, the design of this product is not yet concluded. Engineering Samples may be partially or fully functional, and there may be differences to be published Data Sheet. Engineering Samples are not qualified and are not to be used for reliability testing or series production. Disclaimer: Customer acknowledges that samples may deviate from the Data Sheet and may bear defects due to their status of development and the lack of qualification mentioned above. Panasonic rejects any liability or product warranty for Engineering Samples. In particular, Panasonic disclaims liability for damages caused by  the use of the Engineering Sample other than for Evaluation Purposes, particularly the installation or integration in an other product to be sold by Customer,  deviation or lapse in function of Engineering Sample,  improper use of Engineering Samples. Panasonic disclaimes any liability for consequential and incidental damages. In case of any questions, please contact your local sales partner or the related product manager. 28. REGULATORY INFORMATION 28.1. FCC NOTICE The devices PAN1760, for details refer to Chapter 21, including the antennas, which are listed in 28.5, complies with Part 15 of the FCC Rules. The device meets the requirements for modular transmitter approval as detailed in FCC public Notice DA00-1407.transmitter Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 28.2. CAUTION The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Panasonic Industrial Devices Europe GmbH may void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 31 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help 28.3. LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic FCC identifier for this product as well as the FCC Notice above. The FCC identifier is FCC ID: T7V1760. This FCC identifier is valid for all PAN1760 modules, for details, see the Chapter 21. Ordering Information. In any case the end product must be labelled exterior with "Contains FCC ID: T7V1670" 28.4. ANTENNA WARNING For the related part number of PAN1760 refer to Chapter 21. Ordering Information. This devices are tested with a standard SMA connector and with the antennas listed below. When integrated in the OEMs product, these fixed antennas require installation preventing end-users from replacing them with non-approved antennas. Any antenna not in the following table must be tested to comply with FCC Section 15.203 for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for this device with the antenna listed in item 1 are the same (FCC ID: T7V1760). 28.5. APPROVED ANTENNA LIST Note: We are able to qualify your antenna and will add to this list as that process is completed. Item Part Number Manufacturer Frequency Band Type Gain (dBi) 2 ANT2012 Yageo 2.4GHz Chip-Antenna +2.72 28.6. RF EXPOSURE PAN1760 To comply with FCC RF Exposure requirements, the Original Equipment Manufacturer (OEM) must ensure that the approved antenna in the previous table must be installed. The preceding statement must be included as a CAUTION statement in manuals for products operating with the approved antennas in the previous table to alert users on FCC RF Exposure compliance. Any notification to the end user of installation or removal instructions about the integrated radio module is not allowed. The radiated output power of PAN1760 with mounted ceramic antenna (FCC ID: T7V1760) is far below the FCC radio frequency exposure limits. Nevertheless, the PAN1760 shall be used in such a manner that the potential for human contact during normal operation is minimized. End users may not be provided with the module installation instructions. OEM integrators and end users must be provided with transmitter operating conditions for satisfying RF exposure compliance.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 32 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 29. INDUSTRY CANADA CERTIFICATION PAN1760 is licensed to meet the regulatory requirements of Industry Canada (IC), license: IC: 216Q-1760 Manufacturers of mobile, fixed or portable devices incorporating this module are advised to clarify any regulatory questions and ensure compliance for SAR and/or RF exposure limits. Users can obtain Canadian information on RF exposure and compliance from www.ic.gc.ca. This device has been designed to operate with the antennas listed in Table 20 above, having a maximum gain of 0.9 dBi. Antennas not included in this list or having a gain greater than 0.9 dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. The antenna used for this transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Due to the model size the IC identifier is displayed in the installation instruction only and can not be displayed on the modules label due to the limited size (8.7x15.6mm). 29.1. IC NOTICE The devices PAN1760, for details refer to Chapter 21, including the antennas, which are listed in 28.5, complies with Canada RSS-GEN Rules. The device meets the requirements for modular transmitter approval as detailed in RSS-GEN. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. 29.2. LABELING REQUIREMENTS The Original Equipment Manufacturer (OEM) must ensure that IC labelling requirements are met. This includes a clearly visible label on the outside of the OEM enclosure specifying the appropriate Panasonic IC identifier for this product as well as the IC Notice above. The IC identifier is 216Q-1760. This IC identifier is valid for all PAN1760 modules, for details, see the Chapter 21. Ordering Information. In any case the end product must be labelled exterior with "Contains IC: 216Q-1760" 30. BLUETOOTH CERTIFICATION The Design is listed as Controller Subsystem with QDID: The module is listed as EPL based on Toshibas QDID. To create an EPL, two Subsystems e.g. QDID: and QDID: (software stack) need to be combined.
CLASSIFICATION PRODUCT SPECIFICATION No. DS-1760-2400-102 REV. 0.1 SUBJECT CLASS 2 BLUETOOTH LOW ENERGY SINGLE MODE MODULE PAGE 33 of 33 CUSTOMER’S CODE PAN1760 PANASONIC’S CODE ENW89847A1KF DATE 12.01.2015 PANASONIC INDUSTRIAL DEVICES EUROPE GMBH www.pideu.panasonic.de 31. EUROPEAN R&TTE DECLARATION OF CONFORMITY As a result of the conformity assessment procedure described in Annex III of the Directive 1999/5/EC, the end-customer equipment should be labelled as follows: PAN1760 and their versions in the specified reference design can be used in the following countries: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, The Netherlands, the United Kingdom, Switzerland, and Norway. 32. LIFE SUPPORT POLICY This Panasonic product is not designed for use in life support appliances, devices, or systems where malfunction can reasonably be expected to result in a significant personal injury to the user, or as a critical component in any life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Panasonic customers using or selling these products for use in such applications do so at their own risk and agree to fully indemnify Panasonic for any damages resulting.

Navigation menu